Hoang Le [Thu, 11 Oct 2018 01:43:08 +0000 (08:43 +0700)]
tipc: support binding to specific ip address when activating UDP bearer
INADDR_ANY is hard-coded when activating UDP bearer. So, we could not
bind to a specific IP address even with replicast mode using - given
remote ip address instead of using multicast ip address.
In this commit, we fixed it by checking and switch to use appropriate
local ip address.
before:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **0.0.0.0:6118** 0.0.0.0:*
after:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **10.0.0.2:6118** 0.0.0.0:*
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 16 Oct 2018 04:49:56 +0000 (21:49 -0700)]
Merge tag 'mlx5e-updates-2018-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-10
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit 52a57478c4d6
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
however I think the value of staying within 80 columns is higher than the
value of having the string on a single line. This is because with all the
formatting specifiers there it is not directly greppable based on the
final output produced to the kernel log on one hand, e.g.:
tc2: ROM rev. 1.0, firmware rev. 1.2, RMC rev. A, SMT ver. 1
while it can be easily tracked down by grepping for an obvious substring
such as "RMC rev" on the other.
The issue with MMIO barriers I discussed in the course of the original
review turned out mostly irrelevant to this driver, because as I have
learnt in a recent Alpha/Linux discussion starting here:
<https://marc.info/?i=alpine.LRH.2.02.1808161556450.13597%20()%20file01%20!%20intranet%20!%20prod%20!%20int%20!%20rdu2%20!%20redhat%20!%20com>
our MMIO API mandates the `readX' and `writeX' accessors to be strongly
ordered with respect to each other, even if that is not implicitly
enforced by hardware.
Consequently I have removed all the explicit ordering barriers and
instead submitted a fix for MIPS MMIO implementation, which currently does
not guarantee strong ordering (the MIPS architecture does not define bus
ordering rules except in terms of SYNC barriers), as recorded here:
<https://patchwork.linux-mips.org/project/linux-mips/list/?series=1538>.
Enforcing strong MMIO ordering can be costly however and is often
unnecessary, e.g. when using PIO to access network frame data in onboard
packet memory. I have therefore retained the information that would be
lost by the removal of barriers, by defining accessor wrappers suffixed by
`_o' and `_u', for accesses that have to be ordered and can be unordered
respectively.
If we ever have an API defined for weakly-ordered MMIO accesses, then
these wrappers can be redefined accordingly. Right now they all expand to
the respective `_relaxed' accessors, because, again, enforcing the
ordering WRT DMA transfers can be costly and we don't need it here except
in one place, where I chose to use explicit `dma_rmb' instead.
Similarly I have replaced the completion barriers with a read back from
the respective MMIO location (all adapter MMIO registers can be read with
no side effects incurred), which will serve its purpose on the basis of
MMIO being strongly ordered (although a read from TURBOchannel is going to
be slower than `iob', making the delay incurred unnecessarily longer).
And last but not least, I have split off the SMT Tx network tap support
to a separate change, 2/2 in this series, so that it does not block the
driver proper and can be discussed separately.
I think it has value in that it makes the view of the outgoing network
traffic complete, as if one actually physically tapped into the outgoing
line of the ring, between the station being examined and its downstream
neighbour. Without this part only traffic passed from applications
through the whole protocol stack can be captured and this is only a part
of the view.
With the `dev_queue_xmit_nit' interface now exported it's only
`ptype_all' that remains private, and to define a properly abstracted API
I propose to provide am exported `dev_nit_active' predicate that tells
whether any taps are active. This predicate is then used accordingly.
NB if there is a long-term maintenance concern about the `dev_nit_active'
predicate, then well, corresponding inline code currently present in
`xmit_one' has to be maintained anyway, and if the resulting changes
require `defza' to be updated accordingly, then I am going to handle it;
after some 20 years with Linux it's not that I am going to disappear
anywhere anytime. And once I am dead, which is inevitably going to happen
sooner or later, then the driver can simply be ripped from the kernel.
Though I suspect that at that point no DECstation Linux users may survive
anymore, even though hardware, being as sturdy as it is, likely will.
I have a patch for `tcpdump' to actually decode SMT frames, which I plan
to upstream sometime. Here's a sample of SMT traffic captured through the
`defza' driver in a small network of 4 stations and no concentrators,
printed in the most verbose mode:
FDDI: defza: Support capturing outgoing SMT traffic
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
FDDI: defza: Add support for DEC FDDIcontroller 700 TURBOchannel adapter
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Serhey Popovych [Tue, 9 Oct 2018 18:21:01 +0000 (21:21 +0300)]
tun: Consistently configure generic netdev params via rtnetlink
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: 513e5af037bb ("tun: Implement ip link del tunXXX") Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo [Sun, 14 Oct 2018 08:40:41 +0000 (11:40 +0300)]
Merge tag 'mt76-for-kvalo-2018-10-13' of https://github.com/nbd168/wireless
mt76 patches for 4.20
* mt76x0 fixes
* mt76x0e improvements (should be usable now)
* usb support improvements
* more mt76x0/mt76x2 unification work
* minor fix for aggregation + powersave clients
Govind Singh [Thu, 11 Oct 2018 10:16:26 +0000 (13:16 +0300)]
ath10k: add QMI message handshake for wcn3990 client
Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.
Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by: Niklas Cassel <niklas.cassel@linaro.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Thu, 11 Oct 2018 10:11:45 +0000 (13:11 +0300)]
ath10k: add support to create boardname for non-bmi target
Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Govind Singh <govinds@codeaurora.org> Acked-by: Niklas Cassel <niklas.cassel@linaro.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arnd Bergmann [Tue, 9 Oct 2018 16:03:06 +0000 (18:03 +0200)]
ath9k: fix RX_STAT_INC() etc macros
A couple of macros that deal with statistics in ath9k rely on the
declaration of the 'sc' variable, which they dereference.
However, when the statistics are disabled, the new instance in
ath_cmn_process_fft() causes a warning for an unused variable:
drivers/net/wireless/ath/ath9k/common-spectral.c: In function 'ath_cmn_process_fft':
drivers/net/wireless/ath/ath9k/common-spectral.c:474:20: error: unused variable 'sc' [-Werror=unused-variable]
It's better if those macros only operate on their arguments instead of
known variable names, and adding a cast to (void) kills off that warning.
Fixes: 7246bfd1a695 ("ath9k: add counters for good and errorneous FFT/spectral frames") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 11 Oct 2018 08:09:20 +0000 (11:09 +0300)]
ath10k: htt: remove some dead code
We added an unnecessary condition here in commit a11f093150bc ("ath10k:
add extended per sta tx statistics support"). "legacy_rate_idx" is a u8
so it can't be negative. The caller doesn't pass negatives either. I
have deleted this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Carl Huang [Thu, 11 Oct 2018 07:55:26 +0000 (15:55 +0800)]
ath10k: allocate small size dma memory in ath10k_pci_diag_write_mem
ath10k_pci_diag_write_mem may allocate big size of the dma memory
based on the parameter nbytes. Take firmware diag download as
example, the biggest size is about 500K. In some systems, the
allocation is likely to fail because it can't acquire such a large
contiguous dma memory.
The fix is to allocate a small size dma memory. In the loop,
driver copies the data to the allocated dma memory and writes to
the destination until all the data is written.
Tested with QCA6174 PCI with
firmware-6.bin_WLAN.RM.4.4.1-00119-QCARMSWP-1, this also affects
QCA9377 PCI.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Reviewed-by: Brian Norris <briannorris@chomium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Mon, 8 Oct 2018 09:02:43 +0000 (17:02 +0800)]
ath10k: add peer flush in ath10k_flush for STATION
In the noisy environment, if there are packets in the queue and can't
send out, the suspend timing will be more than 5 seconds due to the wait,
flush the queue to optimize the suspend timing, and let the upper layer to
retry the packets after resume.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k: remove unnecessary comparison of unsigned integer with < 0
There is no need to compare *ps_state_enable* with < 0 because
such variable is of type u8 (8 bits, unsigned), making it
impossible to hold a negative value.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1473921 ("Unsigned compared against 0") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k: htt_rx: fix signedness bug in ath10k_update_per_peer_tx_stats
Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.
Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).
Addresses-Coverity-ID: 1473914 ("Unsigned compared against 0") Fixes: c62f42cef59c ("ath10k: get the legacy rate index to update the txrate table") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding WMI service check for management tx ack rssi support; this is
done to maintain common avg ack signal in user level for both data
and management tx ack packet.
Tested on QCA4019(fw version-10.4-3.2.1-00063).
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Thu, 4 Oct 2018 05:45:31 +0000 (08:45 +0300)]
ath10k: support NET_DETECT WoWLAN feature
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rakesh Pillai [Tue, 2 Oct 2018 18:03:13 +0000 (23:33 +0530)]
ath10k: set probe request oui during driver start
Currently the wmi command for setting probe request
oui, needed for mac randomization, is sent during
the mac register. At this time, during the driver
init the wmi has already been detached. This can
cause unexpected behavior since the firmware is
already down and the wmi has been detached.
Send the wmi command for setting probe request
oui during the driver start. This will make sure
that the firmware is started and wmi is initialized
before we send this command.
Sriram R [Wed, 3 Oct 2018 03:13:50 +0000 (08:43 +0530)]
ath10k: fix possible out of bound access of ath10k_rates array
While using 'ath10k_mac_get_rate_hw_value()' to obtain the hw value
from the passed bitrate, there is a chance of out of bound array access
when wrong bitrate is passed. This is fixed by comparing the bitrates
within the correct size of the ath10k_rates array.
Fixes commit 48f303092c5a ("ath10k: add support for configuring management
packet rate"). Also correction made to some indents used in the above commit.
Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Mon, 8 Oct 2018 14:16:59 +0000 (14:16 +0000)]
rtl8xxxu: Remove set but not used variables 'usedesc40' and 'seq_number'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c: In function 'rtl8xxxu_tx':
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4925:7: warning:
variable 'usedesc40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4921:6: warning:
variable 'seq_number' set but not used [-Wunused-but-set-variable]
'usedesc40' and 'seq_number' are not used any more after
commit 7281f6b4def2 ("rtl8xxxu: Split filling of TX descriptors into separate functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jia-Ju Bai [Fri, 5 Oct 2018 13:55:46 +0000 (21:55 +0800)]
iwlegacy: Add a lock assertion in il4965_send_rxon_assoc()
The variables il->staging.filter_flags, rxon1->filter_flags and
rxon2->filter_flags need to be protected by the mutex lock il->mutex.
This patch adds a lock assertion of il->mutex to check whether
this lock is held.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Beacons are not updated to reflect TIM changes. This is not compliant with
power-saving client stations as the beacons do not have valid TIM and can
cause the network to stall at random occasions and to have highly variable
latencies.
Fix it by updating beacon templates on mac80211 set_tim callback.
Addresses an issue described in:
https://marc.info/?i=20180911163534.21312d08%20()%20manjaro
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi [Fri, 12 Oct 2018 10:16:28 +0000 (12:16 +0200)]
mt76x0: phy: do not run calibration during channel switch
Do not perform phy/vga calibration during channel switch.
Moreover remove mt76x0_agc_save and mt76x0_agc_restore routines
since they are no longer necessary. Furthermore run mt76_set_channel
in order to check if there are pending frames during channel switch
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Fri, 12 Oct 2018 10:16:24 +0000 (12:16 +0200)]
mt76: move rssi_gain_thresh routines in mt76x02-lib module
Move mt76x2_get_rssi_gain_thresh and mt76x2_get_low_rssi_gain_thresh
routines in mt76x02-lib module in order to be reused by mt76x0 driver
for dynamic vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Fri, 12 Oct 2018 10:16:23 +0000 (12:16 +0200)]
mt76x0: phy: add phy/vco temperature compensation
Introduce phy/vco temperature calibration.
Moreover fix configuration of register 67 on bank0
during temperature reading and use mt76_poll utility routine
to poll core34 register.
Furthermore temperature compensation needs to be disabled
if the device supports tssi compensation.
This issue has never been hit since temperature reading is not
actually used by usb code.
Fixes: 4aecf4c3c36a ("mt76x0: phy files") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_tssi_enabled in order to check if tssi compensation
is enabled since mt76x0 condition differs from mt76x2 one.
Moreover move back mt76x02_temp_tx_alc_enabled and mt76x02_tssi_enabled
routines in mt76x2/eeprom.h since they are mt76x2 specific
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
YueHaibing [Mon, 8 Oct 2018 13:21:49 +0000 (13:21 +0000)]
mt76x0: pci: fix set external PA I/O current
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c: In function 'mt76x0e_register_device':
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c:107:8: warning:
variable 'data' set but not used [-Wunused-but-set-variable]
It seems correct value to write is 'data'
Fixes: 867e9a76b83b ("mt76x0: pci: add hw initialization at bootstrap") Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x0: pci: add mt76x0_register_device in mt76x0e_register_device
Run mt76x0_register_device routine in mt76x0e_register_device
in order to register the device to the mac80211 layer.
Moreover init mt76_driver_ops data structure and register
interrupt line
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x0: use bus helper to identify rf access method
Use mt76_is_usb() to identify RF access method instead of
MT76_STATE_MCU_RUNNING flag and add warning since MCU has
to be initialized before we can access RF registers via MCU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Colin Ian King [Mon, 8 Oct 2018 08:50:28 +0000 (09:50 +0100)]
rtlwifi: rtl8821ae: replace _rtl8821ae_mrate_idx_to_arfr_id with generic version
Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.
This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")
Thanks to Joe Perches for spotting this when I submitted an earlier patch.
Fixes: b4cfaaa31290 ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> ACKed-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Luca Coelho [Sat, 13 Oct 2018 06:46:08 +0000 (09:46 +0300)]
iwlwifi: mvm: check return value of rs_rate_from_ucode_rate()
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Julian Wiedmann [Fri, 12 Oct 2018 15:27:14 +0000 (17:27 +0200)]
s390/qeth: add support for IPv6 TSO
This adds TSO6 support for L3 qeth devices.
Just like for standard IPv6 traffic, TSO6 doesn't use IP offload and
thus runs over the normal qeth_xmit() path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 12 Oct 2018 15:27:13 +0000 (17:27 +0200)]
s390/qeth: enhance TSO control sequence
TSO6 requires the full programming sequence, and not just a simple
START command. This implements the additional ENABLE command, and adds
some sanity checks that were missing for the START command.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Oct 2018 18:23:45 +0000 (11:23 -0700)]
Merge branch 'hns3-promisc-next'
Salil Mehta says:
====================
Fixes & small enhancements related to the promisc mode in HNS3
This patch-set presents some fixes and enhancements related to promiscuous
mode and MAC VLAN Table full condition in HNS3 Ethernet Driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 12 Oct 2018 14:34:06 +0000 (15:34 +0100)]
net: hns3: Resume promisc mode and vlan filter status after loopback test
This patch resumes promisc mode and vlan filter status after
loopback test.
Fixes: f2ce16265a24 ("net: hns3: net: hns3: Add support for IFF_ALLMULTI flag") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 12 Oct 2018 14:34:05 +0000 (15:34 +0100)]
net: hns3: Resume promisc mode and vlan filter status after reset
This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 12 Oct 2018 14:34:04 +0000 (15:34 +0100)]
net: hns3: Enable promisc mode when mac vlan table is full
Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.
Fixes: 22c0e2ce21dd ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Oct 2018 17:56:56 +0000 (10:56 -0700)]
Merge tag 'mac80211-next-for-davem-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Highlights:
* merge net-next, so I can finish the hwsim workqueue removal
* fix TXQ NULL pointer issue that was reported multiple times
* minstrel cleanups from Felix
* simplify lib80211 code by not using skcipher, note that this
will conflict with the crypto tree (and this new code here
should be used)
* use new netlink policy validation in nl80211
* fix up SAE (part of WPA3) in client-mode
* FTM responder support in the stack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org CC: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: db649e62 ("fore200e: simplify fore200e_bus usage") Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 12 Oct 2018 03:33:49 +0000 (20:33 -0700)]
net: Evict neighbor entries on carrier down
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 12 Oct 2018 03:17:21 +0000 (20:17 -0700)]
net/ipv6: Add knob to skip DELROUTE message on device down
Another difference between IPv4 and IPv6 is the generation of RTM_DELROUTE
notifications when a device is taken down (admin down) or deleted. IPv4
does not generate a message for routes evicted by the down or delete;
IPv6 does. A NOS at scale really needs to avoid these messages and have
IPv4 and IPv6 behave similarly, relying on userspace to handle link
notifications and evict the routes.
At this point existing user behavior needs to be preserved. Since
notifications are a global action (not per app) the only way to preserve
existing behavior and allow the messages to be skipped is to add a new
sysctl (net/ipv6/route/skip_notify_on_dev_down) which can be set to
disable the notificatioons.
IPv6 route code already supports the option to skip the message (it is
used for multipath routes for example). Besides the new sysctl we need
to pass the skip_notify setting through the generic fib6_clean and
fib6_walk functions to fib6_clean_node and to set skip_notify on calls
to __ip_del_rt for the addrconf_ifdown path.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 12 Oct 2018 01:49:13 +0000 (01:49 +0000)]
net: cdc_ncm: remove set but not used variable 'ctx'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
variable 'ctx' set but not used [-Wunused-but-set-variable]
struct cdc_ncm_ctx *ctx;
It not used any more after
commit ac253a5e8fce ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
David Howells [Fri, 12 Oct 2018 13:00:57 +0000 (14:00 +0100)]
afs: Fix afs_server struct leak
Fix a leak of afs_server structs. The routine that installs them in the
various lookup lists and trees gets a ref on leaving the function, whether
it added the server or a server already exists. It shouldn't increment
the refcount if it added the server.
The effect of this that "rmmod kafs" will hang waiting for the leaked
server to become unused.
Fixes: b7b4753fe8b8 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anilkumar Kolli [Thu, 11 Oct 2018 12:45:03 +0000 (18:15 +0530)]
mac80211: implement ieee80211_tx_rate_update to update rate
Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Ulf writes:
"MMC core:
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card"
* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
libertas: call into generic suspend code before turning off power
mmc: block: avoid multiblock reads for the last sector in SPI mode
nl80211: Add per peer statistics to compute FCS error rate
Add support for drivers to report the total number of MPDUs received
and the number of MPDUs received with an FCS error from a specific
peer. These counters will be incremented only when the TA of the
frame matches the MAC address of the peer irrespective of FCS
error.
It should be noted that the TA field in the frame might be corrupted
when there is an FCS error and TA matching logic would fail in such
cases. Hence, FCS error counter might not be fully accurate, but it can
provide help in detecting bad RX links in significant number of cases.
This FCS error counter without full accuracy can be used, e.g., to
trigger a kick-out of a connected client with a bad link in AP mode to
force such a client to roam to another AP.
projects / kernel.git / log