The Hardware Filter Block code will be used by ethtool functions
when defining flow types so this commit moves the functions in the
file to prevent the need for prototype declarations.
This is broken out to facilitate review.
Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: move clk_wol management to bcmgenet_wol
The GENET_POWER_WOL_MAGIC power up and power down code configures
the device for WoL when suspending and disables the WoL logic when
resuming. It makes sense that this code should also manage the WoL
clocking.
This commit consolidates the logic and moves it earlier in the
resume sequence.
Since the clock is now only enabled if WoL is successfully entered
the wol_active flag is introduced to track that state to keep the
clock enables and disables balanced in case a suspend is aborted.
The MPD_EN hardware bit can't be used because it can be cleared
when the MAC is reset by a deep sleep.
Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: Fix WoL with password after deep sleep
Broadcom STB chips support a deep sleep mode where all register contents
are lost. Because we were stashing the MagicPacket password into some of
these registers a suspend into that deep sleep then a resumption would
not lead to being able to wake-up from MagicPacket with password again.
Fix this by keeping a software copy of the password and program it
during suspend.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code") Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This commit explicitly calls the bcmgenet_set_rx_mode() function when
the network interface is started. This function is normally called by
ndo_set_rx_mode when the flags are changed, but apparently not when
the driver is suspended and resumed.
This change ensures that address filtering or promiscuous mode are
properly restored by the driver after the MAC may have been reset.
Fixes: b6e978e50444 ("net: bcmgenet: add suspend/resume callbacks") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net/smc: preparations for SMC-R link failover
This patch series prepares the SMC code for the implementation of SMC-R link
failover capabilities which are still missing to reach full compliance with
RFC 7609.
The code changes are separated into 65 patches which together form the new
functionality. I tried to create meaningful patches which allow to follow the
implementation.
Question: how to handle the remaining 52 patches? All of them are needed for
link failover to work and should make it into the same merge window.
Can I send them all together?
The SMC-R implementation will transparently make use of the link failover
feature when matching RoCE devices are available, no special setup is required.
All RoCE devices with the same PNET ID as the TCP device (hardware-defined or
user-defined via the smc_pnet tool) are candidates to get used to form a link
in a link group. When at least 2 RoCE devices are available on both
communication endpoints then a symmetric link group is formed, meaning the link
group has 2 independent links. If one RoCE device goes down then all connections
on this link are moved to the surviving link. Upon recovery of the failing
device or availability of a new one, the symmetric link group will be restored.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: move llc layer related init and clear into smc_llc.c
Introduce smc_llc_lgr_init() and smc_llc_lgr_clear() to implement all
llc layer specific initialization and cleanup in module smc_llc.c.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: use mutex instead of rwlock_t to protect buffers
The locks for sndbufs and rmbs are never used from atomic context. Using
a mutex for these locks will allow to nest locks with other mutexes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When llc responses are received then possible waiters for this response
are to be notified. This can be done in tasklet context, without to
use a work in the llc work queue. Move all code that handles llc
responses into smc_llc_rx_response().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: use worker to process incoming llc messages
Incoming llc messages are processed in irq tasklet context, and
a worker is used to send outgoing messages. The worker is needed
because getting a send buffer could result in a wait for a free buffer.
To make sure all incoming llc messages are processed in a serialized way
introduce an event queue and create a new queue entry for each message
which is queued to this event queue. A new worker processes the event
queue entries in order.
And remove the use of a separate worker to send outgoing llc messages
because the messages are processed in worker context already.
With this event queue the serialized llc_wq work queue is obsolete,
remove it.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel the testlink worker during link clear processing and remove the
extra function smc_llc_link_inactive().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The testlink work waits for a response to the testlink request and
blocks the single threaded llc_wq. This type of work does not have to be
serialized and can be moved to the system work queue.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before a link can be reused it must have been cleared. Lowest current
link state is INACTIVE, which does not mean that the link is already
cleared.
Add a new state UNUSED that is set when the link is cleared and can be
reused.
Add helper smc_llc_usable_link() to find an active link in a link group,
and smc_link_usable() to determine if a link is usable.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: multi-link support for smc_rmb_rtoken_handling()
Extend smc_rmb_rtoken_handling() and smc_rtoken_delete() to support
multiple links.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: convert static link ID instances to support multiple links
As a preparation for the support of multiple links remove the usage of
a static link id (SMC_SINGLE_LINK) and allow dynamic link ids.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: convert static link ID to dynamic references
As a preparation for the support of multiple links remove the usage of
a static link id (SMC_SINGLE_LINK) and allow dynamic link ids.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The link_id is the index of the link in the array of the link group.
When a link in the array is reused for a new link, a different unique
link_id should be used, otherwise the index in the array could collide
with the previous link at this array position.
Use a new variable link_idx as array index, and make link_id an
increasing unique id value.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: separate function for link initialization
Move the initialization of a new link into its own function, separate
from smc_lgr_create, to allow more than one link per link group.
Do an extra check if the IB device initialization was successful, and
reset the link state if any error occurs during smcr_link_init().
And rename two existing functions to use the prefix smcr_ to indicate
that they belong to the SMC-R code path.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: rework pnet table to support SMC-R failover
The pnet table stored pnet ids in the smc device structures. When a
device is going down its smc device structure is freed, and when the
device is brought online again it no longer has a pnet id set.
Rework the pnet table implementation to store the device name with their
assigned pnet id and apply the pnet id to devices when they are
registered.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Wed, 29 Apr 2020 03:46:24 +0000 (11:46 +0800)]
net: hns3: adds support for reading module eeprom info
This patch adds support for reading the optical module eeprom
info via "ethtool -m".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Apr 2020 21:40:29 +0000 (14:40 -0700)]
Merge branch 'net-ReST-convert'
Mauro Carvalho Chehab says:
====================
net: manually convert files to ReST format - part 1
There are very few documents upstream that aren't converted upstream.
This series convert part of the networking text files into ReST.
It is part of a bigger set of patches, which were split on parts,
in order to make reviewing task easier.
- add SPDX header;
- add a document title;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark lists as such;
- mark tables as such;
- use footnote markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title using the proper markup;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- mark code blocks and literals as such;
- mark tables as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert generic-hdlc.txt to ReST
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- use footnote markup;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark lists as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- add a document title;
- mark code blocks and literals as such;
- mark lists as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- mark code blocks and literals as such;
- use :field: markup;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- comment out text-only TOC from html/pdf output;
- mark code blocks and literals as such;
- mark tables as such;
- add notes markups;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- use document title markup;
- add notes markups;
- mark code blocks and literals as such;
- mark tables as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
docs: networking: convert arcnet-hardware.txt to ReST
- add SPDX header;
- add document title markup;
- add notes markups;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- use title markups;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 28 Apr 2020 17:58:33 +0000 (19:58 +0200)]
net: ethernet: fec: Prevent MII event after MII_SPEED write
The change to polled IO for MDIO completion assumes that MII events
are only generated for MDIO transactions. However on some SoCs writing
to the MII_SPEED register can also trigger an MII event. As a result,
the next MDIO read has a pending MII event, and immediately reads the
data registers before it contains useful data. When the read does
complete, another MII event is posted, which results in the next read
also going wrong, and the cycle continues.
By writing 0 to the MII_DATA register before writing to the speed
register, this MII event for the MII_SPEED is suppressed, and polled
IO works as expected.
Fixes: 29ae6bd1b0d8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO") Reported-by: Andy Duan <fugang.duan@nxp.com> Suggested-by: Andy Duan <fugang.duan@nxp.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
frames and cdan are both of type __u64 (unsigned long long) so we need
to use div64_u64 to avoid this issues.
Fixes: 460fd830dd9d ("dpaa2-eth: add channel stat to debugfs") Link: https://github.com/ClangBuiltLinux/linux/issues/1012 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: kernelci.org bot <bot@kernelci.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: bcm54140: Make a bunch of functions static
Fix the following warning:
drivers/net/phy/bcm54140.c:663:5: warning:
symbol 'bcm54140_did_interrupt' was not declared. Should it be static?
drivers/net/phy/bcm54140.c:672:5: warning:
symbol 'bcm54140_ack_intr' was not declared. Should it be static?
drivers/net/phy/bcm54140.c:684:5: warning:
symbol 'bcm54140_config_intr' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: ChenTao <chentao107@huawei.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This set is an attempt to make running tests for different
sets of data easier. The direct motivation is the tls
test which we'd like to run for TLS 1.2 and TLS 1.3,
but currently there is no easy way to invoke the same
tests with different parameters.
Tested all users of kselftest_harness.h.
Dave, would it be possible to take these via net-next?
It seems we're failing to get Shuah's attention.
v2:
- don't run tests by fixture
- don't pass params as an explicit argument
v3:
- go back to the orginal implementation with an extra
parameter, and running by fixture (Kees);
- add LIST_APPEND helper (Kees);
- add a dot between fixture and param name (Kees);
- rename the params to variants (Tim);
v4:
- whitespace fixes.
v5 (Kees):
- move a comment;
- remove a temporary variable;
- reword the commit message on patch 4.
Jakub Kicinski [Tue, 28 Apr 2020 01:03:50 +0000 (18:03 -0700)]
kselftest: add fixture variants
Allow users to build parameterized variants of fixtures.
If fixtures want variants, they call FIXTURE_VARIANT() to declare
the structure to fill for each variant. Each fixture will be re-run
for each of the variants defined by calling FIXTURE_VARIANT_ADD()
with the differing parameters initializing the structure.
Since tests are being re-run, additional initialization (steps,
no_print) is also added.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 28 Apr 2020 01:03:47 +0000 (18:03 -0700)]
kselftest: factor out list manipulation to a helper
Kees suggest to factor out the list append code to a macro,
since following commits need it, which leads to code duplication.
Suggested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Apr 2020 19:50:37 +0000 (12:50 -0700)]
Merge branch 'nexthop-API-sysctl'
Roopa Prabhu says:
====================
New sysctl to turn off nexthop API compat mode
Currently route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API if they wish to. Old route API behaviour and support is
not modified by this sysctl
v4:
- Use davids note for Documenting the sysctl
- test with latest iproute2 and adjust 'pref'
v3:
- Document new sysctl
- move sysctl to use proc_dointvec_minmax with 0 and 1 values
- selftest: remove pref medium in ipv6 test
v2:
- Incorporate David Aherns pointers on covering dumps and
nexthop deletes. Also use one ipv4 sysctl to cover
both ipv4 and ipv6 (I see it is done that way for many
others)
- Added a selftest to cover dump and notfications for nexthop
api compat mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: net: add new testcases for nexthop API compat mode sysctl
New tests to check route dump and notifications with
net.ipv4.nexthop_compat_mode on and off.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: add sysctl for nexthop api compatibility mode
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows you to NAT the network address prefix onto another
network address prefix, a.k.a. netmapping.
Userspace must specify the NF_NAT_RANGE_NETMAP flag and the prefix
address through the NFTA_NAT_REG_ADDR_MIN and NFTA_NAT_REG_ADDR_MAX
netlink attributes.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net: ethernet: ti: fix return value check in k3_cppi_desc_pool_create_name()
In case of error, the function gen_pool_create() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8169: improve error message if no dedicated PHY driver is found
There's a number of consumer mainboards where the BIOS leaves the PHY
in a state that it's reporting an invalid PHY ID. To detect such cases
add the PHY ID to the error message if no dedicated PHY driver is found.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the matchall and flower are handled by registering separate
callbacks in mlxsw. That leads to faulty indication "in_hw_count 2" in
filter show command for every inserted flower filter. That happens
because matchall callback just blindly returns 0 for it and it is
wrongly accounted for as "the offloader".
I inspected different ways to fix this problem. The only clean solution
is to rework handling of matchall in mlxsw a bit. The driver newely
registers one callback for bound block which is called for both matchall
and flower filter insertions.
On the way, iron out the matchall code a bit, push it into a separate
file etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_matchall: Process matchall events from the same cb as flower
Currently there are two callbacks registered: one for matchall,
one for flower. This causes the user to see "in_hw_count 2" in TC filter
dump. Because of this and also as a preparation for future matchall
offload for rules equivalent to flower-all-match, move the processing of
shared block into matchall.c. Leave only one cb for mlxsw driver
per-block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Avoid copying sample values and use RCU pointer direcly instead
Currently, only the psample_group is accessed using RCU on RX path.
However, it is possible (unlikely) that other sample values get change
during RX processing. Fix this by having the port->sample struct
accessed as RCU pointer, containing all sample values including
psample_group pointer. That avoids extra alloc per-port, copying the
values and the race condition described above.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_matchall: Pass mall_entry as arg to mlxsw_sp_mall_port_sample_add()
In the preparation for future changes, have the
mlxsw_sp_mall_port_sample_add() function to accept mall_entry including
all needed info originally obtained from cls and act pointers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_matchall: Pass mall_entry as arg to mlxsw_sp_mall_port_mirror_add()
In the preparation for future changes, have the
mlxsw_sp_mall_port_mirror_add() function to accept mall_entry including
the "to_dev" originally obtained from act pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Push matchall bits into a separate file
Similar to flower, have matchall related code in a separate file.
Do some small renaming on the way (consistent "mall" prefixes,
dropped "_tc_", dropped "_port_" where suitable).
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum: Push flow_block related functions into a separate file
The code around flow_block is currently mixed in spectrum_acl.c.
However, as it really does not directly relate to ACL part only,
push the bits into a separate file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>