Fabio Estevam [Tue, 26 Dec 2017 18:04:20 +0000 (16:04 -0200)]
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Commit 915fbe59cbf2fe6 ("ARM: dts: imx: Add missing #phy-cells to
usb-nop-xceiv") missed to update imx51-zii-rdu1.dts probably due to a
merge timing issue, so add #phy-cells here too.
Fabio Estevam [Tue, 26 Dec 2017 17:55:58 +0000 (15:55 -0200)]
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
Remove the leading zero from unit address to fix the following build
warning with W=1:
arch/arm/boot/dts/imx6dl-hummingboard2.dtb: Warning (unit_address_format): Node /soc/aips-bus@2100000/i2c@21a0000/codec@0a unit name should not have leading 0s
SZ Lin [Tue, 26 Dec 2017 04:54:31 +0000 (12:54 +0800)]
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
Add support for Moxa UC-8410A open platform
The UC-8410A computing platform is designed
for embedded communication-centric industrial applications
The features of UC-8410A are:
* QSPI flash
* SD slot
* 3x LAN
* 8x RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with PCIe/USB signal
* 2x USB host
* TPM
* Watchdog
* RTC
* User LEDs
* Beeper
* Push button
Signed-off-by: Jimmy Chen <jimmy.chen@moxa.com> Signed-off-by: Harry YJ Jhou <harryyj.jhou@moxa.com> Signed-off-by: SZ Lin <sz.lin@moxa.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Wed, 20 Dec 2017 23:11:55 +0000 (23:11 +0000)]
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
Switch 2 has an 88e1545 PHY behind it, which is a quad PHY. Only the
first three PHYs are used, the remaining PHY is unused. When we wire
up the SFF sockets in a later commit, the omission of this causes the
fourth PHY to be used for port 3. Specifying the PHYs in DT avoids
the auto-probing of the bus, and discovery of this PHY.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Wed, 20 Dec 2017 23:11:45 +0000 (23:11 +0000)]
ARM: dts: vf610-zii-dev: enable edma1
EDMA1 is required for the SPI controller used on the ZII boards to be
functional. Enable EDMA1.
Fixes: 14c416336820 ("ARM: dts: vfxxx: Enable DMA for DSPI on Vybrid") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 19 Dec 2017 15:36:37 +0000 (13:36 -0200)]
ARM: dts: ls1021a-twr: Remove extra clock cell
There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
Fabio Estevam [Tue, 19 Dec 2017 15:36:36 +0000 (13:36 -0200)]
ARM: dts: ls1021a-qds: Remove extra clock cell
There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
Michael Tretter [Fri, 15 Dec 2017 09:26:24 +0000 (10:26 +0100)]
ARM: dts: imx6q-h100: use usdhc2 VSELECT
The uSDHC controller directly provides a VSELECT signal that can be
muxed to the external voltage select. Mux the VSELECT directly to avoid
using a GPIO.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Mon, 11 Dec 2017 16:58:54 +0000 (16:58 +0000)]
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
Add support for the v1.5 SOM with TI Wi-Fi and eMMC. As the pinmux
settings are different for the microsom, we need to use a separate
board-level dts for this as there is no support for overlays.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Mon, 11 Dec 2017 16:58:49 +0000 (16:58 +0000)]
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
Add support for the v1.5 SOM with TI Wi-Fi but without eMMC. As the
pinmux settings are different for the microsom, we need to use a
separate board-level dts for this as there is no support for overlays.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Mon, 11 Dec 2017 16:58:34 +0000 (16:58 +0000)]
ARM: dts: imx6*-hummingboard2: rework regulators
Name the regulators according to the voltage rails they are feeding in
the schematic. The USB 2-4 regulators are fixed regulators and are always
on, as they are not a VBUS supply for a single USB host port on the i.MX6,
but supply VBUS to ports behind a USB hub and there is currently no way
to model this in mainline.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 19 Dec 2017 18:10:38 +0000 (19:10 +0100)]
ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support
Add support for the Computer on Module Colibri iMX7D 1GB along
with the Colibri Evaluation Board device trees. Follow the usual
hierarchic include model, maintaining shared configuration in
imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Stefan Agner [Tue, 19 Dec 2017 18:10:37 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: add MCP2515 CAN controller
The Colibri Evaluation Carrier Board provides a MCP2515 CAN
controller connected via SPI. Note that the i.MX 7 provides
an internal CAN controller which is much better suited for CAN
operations. Using the MCP2515 with a Colibri iMX7 module is
mainly useful to test the SPI interface.
Stefan Agner [Tue, 19 Dec 2017 18:10:35 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: specify usdhc1 supplies
The usdhc1 controller instance is used to provide the default
SD/MMC capabilities of the Colibri standard. The IO pins are
supplied to the SoC on the module whereas the SD-card is powered
by the Carrier Board supply.
Stefan Agner [Tue, 19 Dec 2017 18:10:30 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: move and rename USB Host power regulator
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Stefan Agner [Wed, 6 Dec 2017 10:29:29 +0000 (11:29 +0100)]
ARM: dts: colibri/apalis: use correct compatible for RTC
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.
Fabio Estevam [Mon, 4 Dec 2017 12:20:15 +0000 (10:20 -0200)]
ARM: dts: imx6qdl-nitrogen6_max: Remove unneeded unit address
Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@3 has a unit name, but no reg property
While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.
Fabio Estevam [Mon, 4 Dec 2017 12:20:14 +0000 (10:20 -0200)]
ARM: dts: imx6q-h100: Remove unneeded unit address
Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a0000/tc358743@f/port@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@0 has a unit name, but no reg property
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:10 +0000 (10:20 -0200)]
ARM: dts: imx6qdl-aristainetos: Move regulators out of simple-bus
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit name, but no reg property
Fabio Estevam [Mon, 4 Dec 2017 12:20:07 +0000 (10:20 -0200)]
ARM: dts: imx53-m53: Remove unneeded reg property
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx53-m53evk.dtb: Warning (unit_address_vs_reg): Node /soc/aips@60000000/i2c@63fc4000/stmpe610@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:06 +0000 (10:20 -0200)]
ARM: dts: imx51-zii-rdu1: Add the unit addresses in sysled
As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
reg property is mandatory, so add the corresponding unit address in
order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled1 has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:05 +0000 (10:20 -0200)]
ARM: dts: imx51-ts4800: Fix syscon and touschscreen nodes
The syscon node has an incorrect notation for its unit address and the
wdt node has an unneeded unit address.
Fix them so that the following build warnings with W=1 are gone:
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000/wdt@e has a unit name, but no reg property
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000 simple-bus unit address format error, expected "10000"
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen simple-bus unit address format error, expected "12000"
Neil Armstrong [Mon, 4 Dec 2017 09:21:09 +0000 (10:21 +0100)]
ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Vanessa Maegima [Thu, 30 Nov 2017 17:55:17 +0000 (15:55 -0200)]
ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts
Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Fabio Estevam [Wed, 29 Nov 2017 18:54:38 +0000 (16:54 -0200)]
ARM: dts: imx6dl: Remove unneeded label and unit address
Remove unneeded label and unit address in order to fix the following
build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux@34 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux@34 has a unit name, but no
Fabio Estevam [Wed, 29 Nov 2017 18:54:37 +0000 (16:54 -0200)]
ARM: dts: imx6dl: Pass the reg properties for mipi nodes
Pass the reg properties for mipi nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@1 has a unit name, but no reg property
Fabio Estevam [Wed, 29 Nov 2017 18:54:34 +0000 (16:54 -0200)]
ARM: dts: imx53: Move nodes which have no reg property out of bus
Move pmu, usbphy0 and usbphy1 nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-ard.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-0 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-1 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Yangbo Lu [Wed, 29 Nov 2017 06:54:58 +0000 (14:54 +0800)]
ARM: dts: ls1021a: fix the value of TMR_FIPER1
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
projects / kernel.git / log