Leo Li [Mon, 4 Nov 2019 14:22:23 +0000 (09:22 -0500)]
drm/amd/display: Send vblank and user events at vsartup for DCN
[Why]
For DCN hardware, the crtc_high_irq handler is assigned to the vstartup
interrupt. This is different from DCE, which has it assigned to vblank
start.
We'd like to send vblank and user events at vstartup because:
* It happens close enough to vupdate - the point of no return for HW.
* It is programmed as lines relative to vblank end - i.e. it is not in
the variable portion when VRR is enabled. We should signal user
events here.
* The pflip interrupt responsible for sending user events today only
fires if the DCH HUBP component is not clock gated. In situations
where planes are disabled - but the CRTC is enabled - user events won't
be sent out, leading to flip done timeouts.
Consequently, this makes vupdate on DCN hardware redundant. It will be
removed in the next change.
[How]
Add a DCN-specific crtc_high_irq handler, and hook it to the VStartup
signal. Inside the DCN handler, we send off user events if the pflip
handler hasn't already done so.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: use previous aux timeout val if no repeater.
[Why]
The aux timeout value is not default before reading link cap.
Setting it to default when lttpr is not enabled causes some monitor
not to light up.
[How]
Read the aux engine timeout value before setting it to extended.
Set the aux engine timeout to its previous value if no lttpr.
1-If at least one repeater is present in the link and we are in non
transparent mode, perform clock recovery then channel equalization
with all repeaters one by one before training DPRX.
2-Mark the end of LT with a repeater by setting training pattern 0
at the end of channel equalization with each repeater.
[Description]
1-Grant extended timeout request. Done once after detection
2-Configure lttpr mode based on lttpr support before LT
3-Account for lttpr cap when determining max link settings
[Description]
When reading link, update the procedure as follows:
1-Set aux timeout to extended: 3.2ms
2-Start with reading lttpr caps
3-Determine if lttpr support should be enabled. Reset aux timeout to
400us if no repeater is found.
drm/amd/display: Add some hardware status in DTN log debugfs
[Why]
For debug purpose, we need to check the following hardware status
in DTN log debugfs:
1.dpp & hubp clock enable;
2.crtc blank enable;
3.link phy status;
[How]
Add the upper information in the amdgpu_dm_dtn_log debugfs.
For CRTC blanked status, since DCN2 and greater reports it on the OPP
instead of OTG, we patch it in after calling optc1_read_otg_states.
Ideally, this should be done in the DCN version specific function hooks.
It has been left as a TODO item.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com> Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Acked-by: Harry Wentland <Harry.Wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Fri, 18 Oct 2019 22:24:59 +0000 (18:24 -0400)]
drm/amd/display: optimize bandwidth after commit streams.
[Why]
System is unable to enter S0i3 due to DISPLAY_OFF_MASK not asserted
in SMU.
[How]
Optimized bandwidth should be called paired and to resolve unplug
display underflow issue, optimize bandwidth after commit streams is
moved to next page flip, in case of S0i3, there is a change for no
flip coming causing display count is 1 in SMU side.
Add optimize bandwidth after commit stream.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Galiffi [Tue, 1 Oct 2019 22:29:56 +0000 (18:29 -0400)]
drm/amd/display: Create debug option to disable v.active clock change policy.
[WHY]
It has been a useful option in debugging GFXOFF and P.State Change issues.
May be required as for platform specific workaround.
[HOW]
Create option in enum dc_debug_options, "disable_vactive_clock_change".
When it is set, dm_dram_clock_change_vactive, will translate into
p_state_change_support: false.
Signed-off-by: David Galiffi <David.Galiffi@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Anthony Koo [Thu, 17 Oct 2019 03:44:55 +0000 (23:44 -0400)]
drm/amd/display: set MSA MISC1 bit 6 while sending colorimetry in VSC SDP
[Why]
It is confusing to sinks if we send VSC SDP only on some format. Today we
signal colorimetry format using MSA while in formats like sRGB.
But when we switch to BT2020 we set the bit to ignore MSA colorimetry and
instead use the colorimetry information in the VSC SDP.
But if sink supports signaling of colorimetry via VSC SDP we should always
set the MSA MISC1 bit 6, instead of doing so selectively.
[How]
If sink supports signaling of colorimetry via VSC SDP, and we are sending
the colorimetry info via VSC SDP with packet revision 05h, then always
set MSA MISC1 bit 6.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nikola Cornij [Wed, 16 Oct 2019 18:34:15 +0000 (14:34 -0400)]
drm/amd/display: Add a sanity check for DSC already enabled/disabled
[why]
If acquire/release DSC resource sequence is affected by a regression,
it can happen that the already-in-use DSC HW block is being wrongly
re-used for a different pipe. The reverse is also possible, i.e.
already-disabled DSC HW block could be disabled from other context.
[how]
Read back the enable state of DSC HW and report an error if duplicate
enable or disable was attempted.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sung Lee [Wed, 16 Oct 2019 14:24:01 +0000 (10:24 -0400)]
drm/amd/display: Use SIGNAL_TYPE_NONE in disable_output unless eDP
[WHY]
Currently made a change where disable_output is called using signal_type.
Using actual signal_type when calilng disable_output in power_down_encoders
would make DP to HDMI dongle not light up on boot. As it would have signal_type
SIGNAL_TYPE_DISPLAY_PORT.
[HOW]
Set signal_type to SIGNAL_TYPE_NONE unless it is eDP.
Signed-off-by: Sung Lee <sung.lee@amd.com> Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Fri, 11 Oct 2019 19:34:20 +0000 (15:34 -0400)]
drm/amd/display: Renoir chroma viewport WA
[Why]
For unknown reason, immediate flip with host VM translation on NV12
surface will underflow on last row of PTE.
[How]
Hack chroma viewport height to make fetch one more row of PTE.
Note that this will cause hubp underflow on all video underlay
cases, but the underflow is not user visible since it is in
blank region.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David Galiffi [Sat, 12 Oct 2019 20:18:32 +0000 (16:18 -0400)]
drm/amd/display: Fix assert observed when performing dummy p-state check
[WHY]
V.Active dram clock change workaround need a small modification for DMLv2
to ensure that the dummy p-state check doesn't fail.
Signed-off-by: David Galiffi <David.Galiffi@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need DMCUB on Renoir to support DMCU and PHY initialization.
The DMUB service provides a mechanism to load the DMCUB.
[How]
Include the DMUB service in amdgpu_dm.
Frontdoor loading of the DMCUB firmware needs to happen via PSP. To
pass the firmware to PSP we need to hand it off to the firmware list
in the base driver during software initialization.
Most of the DMUB service can technically be initialized at this point
in time, but we don't want to be allocating framebuffer memory for
hardware that doesn't support the DMCUB and in order to check that we
need to be able to read registers - something DM helpers aren't setup
to do in software initialization.
So everything but the service creation itself will get deferred to
hardware initialization.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Fri, 18 Oct 2019 01:44:50 +0000 (21:44 -0400)]
drm/amd/display: Add PSP FW version mask.
[Why]
PSP version format is AB.CD.EF.GH, where CD and GH is the main version.
current psp version check for dmcub loading dmcu check 0x00110029, in
case of some psp version eg: 0x00110227 which main version should be
0x00110027, will result in unexpeceted dmcub loading dmcu FW.
[How]
Add psp version mask 0x00FF00FF for checking version.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Sat, 12 Oct 2019 20:06:19 +0000 (16:06 -0400)]
drm/amd/display: Change dmcu init sequence for dmcub loading dmcu FW.
[Why]
DMCU isn't intiliazed properly by dmcub loading due to dmcub initialize
sequence.
[How]
Change dmcu init sequece to meet dmcub initilize.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's required to support Renoir features so it will be enabled and
compiled automatically when the Renoir display engine is enabled via
CONFIG_DRM_AMD_DC_DCN2_1.
DMUB code will initially be guarded by CONFIG_DRM_AMD_DC_DMUB and later
switched to CONFIG_DRM_AMD_DC_DCN2_1 with the config option dropped.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Add PSP loading support for DMCUB ucode
DMCUB ucode requires secure loading through PSP. This is already
supported in PSP as GFX_FW_TYPE_DMUB, it just needs to be mapped from
AMDGPU_UCODE_ID_DMCUB to GFX_FW_TYPE_DMUB.
DMUB is a shorthand name for DMCUB and can be used interchangeably.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Colin Ian King [Fri, 8 Nov 2019 14:38:14 +0000 (14:38 +0000)]
drm/amd/display: fix dereference of pointer aconnector when it is null
Currently pointer aconnector is being dereferenced by the call to
to_dm_connector_state before it is being null checked, this could
lead to a null pointer dereference. Fix this by checking that
aconnector is null before dereferencing it.
Addresses-Coverity: ("Dereference before null check") Reviewed-by: Mikita Lipski <mikita.lipski@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mikita Lipski [Wed, 6 Nov 2019 19:23:55 +0000 (14:23 -0500)]
drm/amd/display: Add MST atomic routines
- Adding encoder atomic check to find vcpi slots for a connector
- Using DRM helper functions to calculate PBN
- Adding connector atomic check to release vcpi slots if connector
loses CRTC
- Calculate PBN and VCPI slots only once during atomic
check and store them on crtc_state to eliminate
redundant calculation
- Call drm_dp_mst_atomic_check to verify validity of MST topology
during state atomic check
v2: squashed previous 3 separate patches, removed DSC PBN calculation,
and added PBN and VCPI slots properties to amdgpu connector
v3:
- moved vcpi_slots and pbn properties to dm_crtc_state and dc_stream_state
- updates stream's vcpi_slots and pbn on commit
- separated patch from the DSC MST series
v4:
- set vcpi_slots and pbn properties to dm_connector_state
- copy porperties from connector state on to crtc state
v5:
- keep the pbn and vcpi values only on connnector state
- added a void pointer to the stream state instead on two ints,
because dc_stream_state is OS agnostic. Pointer points to the
current dm_connector_state.
v6:
- Remove new param from stream
v7:
- Fix error with using max capable bpc
v8:
- squash in fix from Gustavo A. R. Silva
Reviewed-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Matt Coffin [Mon, 11 Nov 2019 18:36:31 +0000 (11:36 -0700)]
drm/amdgpu/smu_v11: Unify and fix power limits
[Why]
On Navi10, and presumably arcterus, updating pp_table via sysfs would
not re-scale the maximum possible power limit one can set. On navi10,
the SMU code ignored the power percentage overdrive setting entirely,
and would not allow you to exceed the default power limit at all.
[How]
Adding a function to the SMU interface to get the pptable version of the
default power limit allows ASIC-specific code to provide the correct
maximum-settable power limit for the current pptable.
v3: fix spelling (Alex)
Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Matt Coffin <mcoffin13@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Matt Coffin [Fri, 8 Nov 2019 21:28:06 +0000 (14:28 -0700)]
drm/amdgpu/navi10: implement sclk/mclk OD via pp_od_clk_voltage
[Why]
Before this patch, there was no way to use pp_od_clk_voltage on navi
[How]
Similar to the vega20 implementation, but using the common smc_v11_0
headers, implemented the pp_od_clk_voltage API for navi10's pptable
implementation
Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Matt Coffin <mcoffin13@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jesse Zhang [Fri, 8 Nov 2019 10:06:07 +0000 (18:06 +0800)]
drm/amd/amdgpu: finish delay works before release resources
flush/cancel delayed works before doing finalization
to avoid concurrently requests.
Signed-off-by: Jesse Zhang <zhexi.zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 8 Nov 2019 16:15:17 +0000 (11:15 -0500)]
drm/amdgpu/powerplay/smu7: fix AVFS handling with custom powerplay table
When a custom powerplay table is provided, we need to update
the OD VDDC flag to avoid AVFS being enabled when it shouldn't be.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205393 Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 11 Nov 2019 04:26:36 +0000 (12:26 +0800)]
drm/amdgpu: avoid upload corrupted ta ucode to psp
xgmi, ras, hdcp and dtm ta are actually separated ucode and
need to handled case by case to upload to psp.
We support the case that ta binary have one or multiple of
them built-in. As a result, the driver should check each ta
binariy's availablity before decide to upload them to psp.
In the terminate (unload) case, the driver will check the
context readiness before perform unload activity. It's fine
to keep it as is.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Le Ma <Le.Ma@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 7 Nov 2019 14:50:18 +0000 (09:50 -0500)]
drm/amdgpu/powerplay: fix AVFS handling with custom powerplay table
When a custom powerplay table is provided, we need to update
the OD VDDC flag to avoid AVFS being enabled when it shouldn't be.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205393 Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Feng [Fri, 8 Nov 2019 05:20:30 +0000 (13:20 +0800)]
drm/amd/powerplay: dynamically disable ds and ulv for compute
This is to improve the performance in the compute mode
for vega10. For example, the original performance for a rocm
bandwidth test: 2G internal GPU copy, is about 99GB/s.
With the idle power features disabled dynamically, the porformance
is promoted to about 215GB/s.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
changzhu [Thu, 7 Nov 2019 06:09:27 +0000 (14:09 +0800)]
drm/amdgpu: allow direct upload save restore list for raven2
It will cause modprobe atombios stuck problem in raven2 if it doesn't
allow direct upload save restore list from gfx driver.
So it needs to allow direct upload save restore list for raven2
temporarily.
Fixes: 9fbde645a31c ("drm/sched: Use completion to wait for sched->thread idle v2.") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
During GPU reset we call the GPU scheduler to suspend it's
thread, those two functions in amdgpu also suspend and resume
the sceduler for their needs but this can collide with GPU
reset in progress and accidently restart a suspended thread
before time.
Fix:
Serialize with GPU reset.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/sched: Avoid job cleanup if sched thread is parked.
When the sched thread is parked we assume ring_mirror_list is
not accessed from here.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/sched: Use completion to wait for sched->thread idle v2.
Removes thread park/unpark hack from drm_sched_entity_fini and
by this fixes reactivation of scheduler thread while the thread
is supposed to be stopped.
v2: Per sched entity completion.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Suggested-by: Christian König <christian.koenig@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 5 Nov 2019 10:53:30 +0000 (18:53 +0800)]
drm/amdgpu: fix sysfs interface pcie_replay_count error on navi asic
the asic callback function of get_pcie_replay_count is not implement on navi asic,
it will cause null pinter error when read this interface.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Kent Russell <kent.russell@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Emily Deng [Thu, 7 Nov 2019 02:26:43 +0000 (10:26 +0800)]
drm/amdgpu: Need to disable msix when unloading driver
For driver reload test, it will report "can't enable
MSI (MSI-X already enabled)".
Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Oak Zeng [Wed, 6 Nov 2019 17:18:54 +0000 (11:18 -0600)]
drm/amdgpu: Add comments to gmc structure
Explain fields like aper_base, agp_start etc. The definition
of those fields are confusing as they are from different view
(CPU or GPU). Add comments for easier understand.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com> Reviewed-by: Alex Deucher <Alex.Deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pan Bian [Wed, 6 Nov 2019 11:35:43 +0000 (19:35 +0800)]
drm/amdgpu: fix double reference dropping
The reference to object fence is dropped at the end of the loop.
However, it is dropped again outside the loop. The reference can be
dropped immediately after calling dma_fence_wait() in the loop and
thus the dropping operation outside the loop can be removed.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pan Bian [Wed, 6 Nov 2019 09:14:45 +0000 (17:14 +0800)]
drm/amdgpu: fix potential double drop fence reference
The object fence is not set to NULL after its reference is dropped. As a
result, its reference may be dropped again if error occurs after that,
which may lead to a use after free bug. To avoid the issue, fence is
explicitly set to NULL after dropping its reference.
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Huang [Tue, 5 Nov 2019 21:29:57 +0000 (16:29 -0500)]
drm/amdgpu: change read of GPU clock counter on Vega10 VF
Using unified VBIOS has performance drop in sriov environment.
The fix is switching to another register instead.
Signed-off-by: Eric Huang <JinhuiEric.Huang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
changzhu [Tue, 5 Nov 2019 10:29:12 +0000 (18:29 +0800)]
drm/amdgpu: add warning for GRBM 1-cycle delay issue in gfx9
It needs to add warning to update firmware in gfx9
in case that firmware is too old to have function to
realize dummy read in cp firmware.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
changzhu [Thu, 10 Oct 2019 03:02:33 +0000 (11:02 +0800)]
drm/amdgpu: add dummy read by engines for some GCVM status registers in gfx10
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where
status registers requiring HW to update have a 1 cycle delay, due
to the register update having to go through GRBM.
For cp ucode, it has realized dummy read in cp firmware.It covers
the use of WAIT_REG_MEM operation 1 case only.So it needs to call
gfx_v10_0_wait_reg_mem in gfx10. Besides it also needs to add warning to
update firmware in case firmware is too old to have function to realize
dummy read in cp firmware.
For sdma ucode, it hasn't realized dummy read in sdma firmware. sdma is
moved to gfxhub in gfx10. So it needs to add dummy read in driver
between amdgpu_ring_emit_wreg and amdgpu_ring_emit_reg_wait for sdma_v5_0.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Wed, 6 Nov 2019 04:40:12 +0000 (12:40 +0800)]
drm/amd/powerplay: fix deadlock on setting power_dpm_force_performance_level
smu_enable_umd_pstate() will try to get the smu->mutex which was already
hold by its parent API smu_force_performance_level() on the call path.
Thus deadlock happens.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Tue, 5 Nov 2019 07:15:33 +0000 (15:15 +0800)]
drm/amdgpu: perform p-state switch after the whole hive initialized
P-state switch should be performed after all devices from the hive
get initialized.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Reviewed-by: Jonathan Kim <Jonathan.Kim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Thu, 31 Oct 2019 06:15:29 +0000 (14:15 +0800)]
drm/amdgpu: fix possible pstate switch race condition
Added lock protection so that the p-state switch will
be guarded to be sequential. Also update the hive
pstate only all device from the hive are in the same
state.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Tue, 5 Nov 2019 10:13:49 +0000 (18:13 +0800)]
drm/amdgpu: register gpu instance before fan boost feature enablment
Otherwise, the feature enablement will be skipped due to wrong count.
Fixes: ab248e9b88a81df ("drm/amdgpu: fix a race in GPU reset with IB test (v2)") Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 5 Nov 2019 10:16:38 +0000 (18:16 +0800)]
drm/amd/swSMU: fix smu workload bit map error
fix workload bit (WORKLOAD_PPLIB_COMPUTE_BIT) map error
on vega20 and navi asic.
fix commit:
drm/amd/powerplay: add function get_workload_type_map for swsmu
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Le Ma <Le.Ma@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 4 Nov 2019 08:20:06 +0000 (16:20 +0800)]
drm/amdgpu: disallow direct upload save restore list from gfx driver
Direct uploading save/restore list via mmio register writes breaks the security
policy. Instead, the driver should pass s&r list to psp.
For all the ASICs that use rlc v2_1 headers, the driver actually upload s&r list
twice, in non-psp ucode front door loading phase and gfx pg initialization phase.
The latter is not allowed.
VG12 is the only exception where the driver still keeps legacy approach for S&R
list uploading. In theory, this can be elimnated if we have valid srcntl ucode
for VG12.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Candice Li <Candice.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/sched: Fix passing zero to 'PTR_ERR' warning v2
Fix a static code checker warning.
v2: Drop PTR_ERR_OR_ZERO.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojie Yuan [Wed, 30 Oct 2019 03:38:53 +0000 (11:38 +0800)]
drm/amd/powerplay: print the pptable provider
So we know where the tables came from.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com> Reviewed-by: Kevin Wang <kevin1.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Zhan Liu [Sat, 2 Nov 2019 01:10:17 +0000 (21:10 -0400)]
drm/amd/display: Add ENGINE_ID_DIGD condition check for Navi14
[Why]
Navi10 has 6 PHY, but Navi14 only has 5 PHY, that is
because there is no ENGINE_ID_DIGD in Navi14. Without
this patch, many HDMI related issues (e.g. HDMI S3
resume failure, HDMI pink screen on boot) will be
observed.
[How]
If "eng_id" is larger than ENGINE_ID_DIGD, then
add "eng_id" by 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Neil Mayhew [Wed, 30 Oct 2019 18:58:37 +0000 (12:58 -0600)]
drm/amdgpu: Show resolution correctly in mode validation debug output
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Neil Mayhew <neil@neil.mayhew.name> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Thu, 31 Oct 2019 01:41:19 +0000 (09:41 +0800)]
drm/amd/powerplay: support xgmi pstate setting on powerplay routine V2
Add xgmi pstate setting on powerplay routine.
V2: split the change of is_support_sw_smu_xgmi into a separate patch
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Thu, 31 Oct 2019 06:29:48 +0000 (14:29 +0800)]
drm/amd/powerplay: update is_sw_smu_xgmi check
Add check for is_sw_smu routine and drop check
for amdgpu_dpm which seems non-sense.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Thu, 31 Oct 2019 06:10:27 +0000 (14:10 +0800)]
drm/amdgpu: change pstate only after all XGMI device initialized
Pstate settings should be performed after all device of the
XGMI setup get initialized.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Shirish S [Wed, 30 Oct 2019 08:50:46 +0000 (14:20 +0530)]
drm/amdgpu: dont schedule jobs while in reset
[Why]
doing kthread_park()/unpark() from drm_sched_entity_fini
while GPU reset is in progress defeats all the purpose of
drm_sched_stop->kthread_park.
If drm_sched_entity_fini->kthread_unpark() happens AFTER
drm_sched_stop->kthread_park nothing prevents from another
(third) thread to keep submitting job to HW which will be
picked up by the unparked scheduler thread and try to submit
to HW but fail because the HW ring is deactivated.
[How]
grab the reset lock before calling drm_sched_entity_fini()
Signed-off-by: Shirish S <shirish.s@amd.com> Suggested-by: Christian König <christian.koenig@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chenwandun [Thu, 31 Oct 2019 09:43:49 +0000 (17:43 +0800)]
drm/dp_mst: fix gcc compile error
drivers/gpu/drm/drm_dp_mst_topology.c: In function __topology_ref_save:
drivers/gpu/drm/drm_dp_mst_topology.c:1424:6: error: implicit declaration of function stack_trace_save; did you mean stack_depot_save? [-Werror=implicit-function-declaration]
n = stack_trace_save(stack_entries, ARRAY_SIZE(stack_entries), 1);
^~~~~~~~~~~~~~~~
stack_depot_save
drivers/gpu/drm/drm_dp_mst_topology.c: In function __dump_topology_ref_history:
drivers/gpu/drm/drm_dp_mst_topology.c:1513:3: error: implicit declaration of function stack_trace_snprint; did you mean acpi_trace_point? [-Werror=implicit-function-declaration]
stack_trace_snprint(buf, PAGE_SIZE, entries, nr_entries, 4);
^~~~~~~~~~~~~~~~~~~
acpi_trace_point
stack_trace_save and stack_trace_snprint are declared in <linux/stacktrace.h>,
so there is need to include it, and <linux/stackdepot.h> is already included
by practices, so just replace <linux/stackdepot.h> by <linux/stacktrace.h>.
Dave Airlie [Sun, 3 Nov 2019 23:56:25 +0000 (09:56 +1000)]
Merge tag 'drm-intel-next-2019-11-01-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
- Make context persistence optional
Allow userspace to tie the context lifetime to FD lifetime,
effectively allowing Ctrl-C killing of a process to also clean
up the hardware immediately.
Compute changes: https://github.com/intel/compute-runtime/pull/228
The compute driver is shipping in Ubuntu. uAPI acked by Mesa folks.
- Put future HW and their uAPIs under STAGING & BROKEN
Introduces DRM_I915_UNSTABLE Kconfig menu for working on the new
uAPI for future HW in upstream. We already disable driver loading
by default the platform is deemed ready. This is a second level
of protection based on compile time switch (STAGING & BROKEN).
- Under DRM_I915_UNSTABLE: Add the fake lmem region on iGFX
Fake local memory region on integrated GPU through cmdline:
memmap=2G$16G i915.fake_lmem_start=0x400000000
Currently allows testing non-mappable GGTT behavior and running
kernel selftest for local memory.
Driver Changes:
- Fix Bugzilla #112084: VGA external monitor not working (Ville)
- Add support for half float framebuffers (Ville)
- Add perf support on TGL (Lionel)
- Replace hangcheck by heartbeats (Chris)
- Allow SPT PCH on all AML devices (James)
- Add new CNL PCH for CML platform (Imre)
- Allow 100 ms (Kconfig) for workloads to exit before reset (Chris, Jon, Joonas)
- Forcibly pre-empt a context after 100 ms (Kconfig) of delay (Chris)
- Make timeslice duration Kconfig configurable (Chris)
- Whitelist PS_(DEPTH|INVOCATION)_COUNT for Tigerlake (Tapani)
- Support creating LMEM objects in kernel (Matt A)
- Adjust the location of RING_MI_MODE in the context image for TGL (Chris)
- Handle AUX interrupts for TC ports (Matt R)
- Add support for devices without mappable GGTT aperture (Daniele)
- Rename "inject_load_failure" module parameter to "inject_probe_failure" (Janusz)
- Handle fused off HDCP, FBC, DMC and DSC (Jose)
- Add support to one DP-MST stream on Tigerlake (Lucas)
- Add HuC firmware (and GuC) for TGL (Daniele)
- Allow ICL+ DSI on any pipe (Ville)
- Check some transcoder timing minimum limits (Ville)
- Don't set queue_priority_hint if we don't kick the submission (Chris)
- Introduce barrier pulses along engines to flush idle/in-flight requests (Chris)
- Drop assertion that ce->pin_mutex guards state updates (Chris)
- Cancel banned contexts on schedule-out (Chris)
- Cancel contexts when hangchecking is disabled (Chris)
- Catch GTT fault errors for gen11+ planes (Matt R)
- Print in debugfs if PSR is not enabled because of sink (Jose)
- Do not set MOCS control values on dgfx (Lucas)
- Setup io-mapping for LMEM (Abdiel)
- Support kernel mapping of LMEM objects (Abdiel)
- Add LMEM selftests (Matt A)
- Initialise PMU spinlock before registering (Chris)
- Clear DKL_TX_PMD_LANE_SUS before program TC voltage swing (Jose)
- Flip interpretation of ips fmin/fmax to max rps (Chris)
- Add VBT compression parameter block definition (Jani)
- Limit the blitter sizes to ensure low preemption latency (Chris)
- Fixup block_size rounding on BLT (Matt A)
- Don't try to place HWS in non-existing mappable region (Michal Wa)
- Don't allocate the ring in stolen if we lack aperture (Matt A)
- Add AUX B & C to DC_OFF_POWER_DOMAINS for Tigerlake (Matt R)
- Avoid HPD poll detect triggering a new detect cycle (Imre)
- Document the userspace fail with possible_crtcs (Ville)
- Drop lrc header page now unused by GuC (Daniele)
- Do not switch aux to TBT mode for non-TC ports (Jose)
- Restructure code to avoid depending on i915 but smaller structs (Chris, Tvrtko, Andi)
- Remove pm park/unpark notifications (Chris)
- Avoid lockdep cross-contamination between object types (Chris)
- Restructure DSC code (Jani)
- Fix dead locking in early workload shadow (Zhenyu)
- Split the legacy submission backend from the common CS ring buffer (Chris)
- Move intel_engine_context_in/out into intel_lrc.c (Tvrtko)
- Describe perf/wakeref structure members in documentation (Anna)
- Update renamed header files names in documentation (Anna)
- Add debugs to distingiush a cd2x update from a full cdclk pll update (Ville)
- Rework atomic global state locking (Ville)
- Allow planes to declare their minimum acceptable cdclk (Ville)
- Eliminate skl_check_pipe_max_pixel_rate() and simplify skl_max_scale() (Ville)
- Making loglevel of PSR2/SU logs same (Ap)
- Capture aux page table error register (Lionel)
- Add is_dgfx to device info (Jose)
- Split gen11_irq_handler to make it shareable (Lucas)
- Encapsulate kconfig constant values inside boolean predicates (Chris)
- Split memory_region initialisation into its own file (Chris)
- Use _PICK() for CHICKEN_TRANS() and add CHICKEN_TRANS_D (Ville)
- Add perf helper macros for comparing with whitelisted registers (Umesh)
- Fix i915_inject_load_error() name to read *_probe_* (Janusz)
- Drop unused AUX register offsets (Matt R)
- Provide more information on DP AUX failures (Matt R)
- Add GAM/SFC instdone to error state (Mika)
- Always track callers to intel_rps_mark_interactive() (Chris)
- Nuke 'mode' argument to intel_get_load_detect_pipe() (Ville)
- Simplify LVDS crtc_mask and pipe_mask setup (Ville)
- Stop frobbing crtc->base.mode (Ville)
- Do s/crtc_mask/pipe_mask/ (Ville)
- Split detaching and removing the vma (Chris)
- Selftest improvements (Chris, Tvrtko, Mika, Matt A, Lionel)
- GuC code improvements (Rob, Andi, Daniele)
- Check against i915_selftest only under CONFIG_SELFTEST (Chris)
- Refine occupancy test in kill_context() (Chris)
- Start kthreads before stopping (Chris)
Dave Airlie [Sun, 3 Nov 2019 23:47:45 +0000 (09:47 +1000)]
Merge tag 'drm/tegra/for-5.5-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v5.5-rc1
The bulk of these changes is the addition of DisplayPort support for
Tegra210, Tegra186 and Tegra194. I've been running versions of this for
about three years now, so I'd consider these changes to be pretty
mature. These changes also unify the existing eDP support with the DP
support since the programming is very similar, except for a few steps
that can be easily parameterized.
The rest are a couple of fixes all over the place for minor issues, as
well as some work to support the IOMMU-backed DMA API, which in the end
turned out to also clean up a number of cases where the DMA API was not
being used correctly.
Dave Airlie [Sun, 3 Nov 2019 23:27:41 +0000 (09:27 +1000)]
Merge tag 'drm-misc-next-2019-10-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.5:
UAPI Changes:
-dma-buf: Introduce and revert dma-buf heap (Andrew/John/Sean)
Cross-subsystem Changes:
- None
Core Changes:
-dma-buf: add dynamic mapping to allow exporters to choose dma_resv lock
state on mmap/munmap (Christian)
-vram: add prepare/cleanup fb helpers to vram helpers (Thomas)
-ttm: always keep bo's on the lru + ttm cleanups (Christian)
-sched: allow a free_job routine to sleep (Steven)
-fb_helper: remove unused drm_fb_helper_defio_init() (Thomas)
Driver Changes:
-bochs/hibmc/vboxvideo: Use new vram helpers for prepare/cleanup fb (Thomas)
-amdgpu: Implement dma-buf import/export without drm helpers (Christian)
-panfrost: Simplify devfreq integration in driver (Steven)
Cc: Christian König <christian.koenig@amd.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Steven Price <steven.price@arm.com> Cc: Andrew F. Davis <afd@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Sean Paul <seanpaul@chromium.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20191031193015.GA243509@art_vandelay
Chris Wilson [Fri, 1 Nov 2019 08:49:40 +0000 (08:49 +0000)]
drm/i915/selftests: Start kthreads before stopping
An interesting observation made with our parallel selftests was that on
our small/single cpu systems we would call kthread_stop() before the
kthreads were spawned. If this happens, the kthread is never run at all;
completely bypassing the test.
A simple yield() from the parent will ensure that all children have the
opportunity to start before we reap them.
Thierry Reding [Thu, 29 Aug 2019 15:52:42 +0000 (17:52 +0200)]
drm/tegra: Unconditionally select IOMMU_IOVA
Currently configurations can be generated where IOMMU_SUPPORT is
disabled but IOMMU_IOVA is built as a module and DRM_TEGRA as built-in.
In such a case, the symbols guarded by IOMMU_IOVA will not be available
when linking the Tegra DRM driver and cause a linking failure.
Simplify this by unconditionally selecting IOMMU_IOVA, which makes sure
that it will be forced to =y if DRM_TEGRA=y. Technically we can now get
IOMMU_IOVA code built-in even if we don't use it (Tegra DRM only uses it
when IOMMU_SUPPORT is also enabled), but such configuration are of a
mostly academic nature. In all practical configurations we want IOMMU
support anyway.
Thierry Reding [Thu, 29 Aug 2019 15:56:53 +0000 (17:56 +0200)]
gpu: host1x: Unconditionally select IOMMU_IOVA
Currently configurations can be generated where IOMMU_SUPPORT is
disabled but IOMMU_IOVA is built as a module and HOST1X as built-in. In
such a case, the symbols guarded by IOMMU_IOVA will not be available
when linking the host1x driver and cause a linking failure.
Simplify this by unconditionally selecting IOMMU_IOVA, which makes sure
that it will be forced to =y if HOST1X=y. Technically we can now get
IOMMU_IOVA code built-in even if we don't use it (host1x only uses it
when IOMMU_SUPPORT is also enabled), but such configuration are of a
mostly academic nature. In all practical configurations we want IOMMU
support anyway.
Chris Wilson [Thu, 31 Oct 2019 09:01:04 +0000 (09:01 +0000)]
drm/i915/gem: Refine occupancy test in kill_context()
Don't just look at the very last request in a queue when deciding if we
need to evict the context from the GPU, as that request may still be in
the submission queue while the rest of the context is running!
Instead, walk back along the queued requests looking for the active
request and checking that.
Fixes: a16f09a47227 ("drm/i915/gem: Cancel contexts when hangchecking is disabled")
Testcase: igt/gem_ctx_persistence/queued Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Matthew Auld <matthew.auld@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191031090104.22245-1-chris@chris-wilson.co.uk
Matthew Auld [Wed, 30 Oct 2019 17:33:20 +0000 (17:33 +0000)]
drm/i915/lmem: add the fake lmem region
Intended for upstream testing so that we can still exercise the LMEM
plumbing and !i915_ggtt_has_aperture paths. Smoke tested on Skull Canyon
device. This works by allocating an intel_memory_region for a reserved
portion of system memory, which we treat like LMEM. For the LMEMBAR we
steal the aperture and 1:1 it map to the stolen region.
To enable simply set the i915 modparam fake_lmem_start= on the kernel
cmdline with the start of reserved region(see memmap=). The size of the
region we can use is determined by the size of the mappable aperture, so
the size of reserved region should be >= mappable_end. For now we only
enable for the selftests. Depends on CONFIG_DRM_I915_UNSTABLE being
enabled.
Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191030173320.8850-1-matthew.auld@intel.com
drm/i915/dp: Do not switch aux to TBT mode for non-TC ports
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
projects / kernel.git / log