Michal Hocko [Wed, 11 Jan 2017 00:57:39 +0000 (16:57 -0800)]
mm: fix remote numa hits statistics
Jia He has noticed that commit a4a093c0468a ("mm, page_alloc: reduce
branches in zone_statistics") has an unintentional side effect that
remote node allocation requests are accounted as NUMA_MISS rathat than
NUMA_HIT and NUMA_OTHER if such a request doesn't use __GFP_OTHER_NODE.
There are many of these potentially because the flag is used very rarely
while we have many users of __alloc_pages_node.
Fix this by simply ignoring __GFP_OTHER_NODE (it can be removed in a
follow up patch) and treat all allocations that were satisfied from the
preferred zone's node as NUMA_HITS because this is the same node we
requested the allocation from in most cases. If this is not the local
node then we just account it as NUMA_OTHER rather than NUMA_LOCAL.
One downsize would be that an allocation request for a node which is
outside of the mempolicy nodemask would be reported as a hit which is a
bit weird but that was the case before a4a093c0468a already.
Fixes: a4a093c0468a ("mm, page_alloc: reduce branches in zone_statistics") Link: http://lkml.kernel.org/r/20170102153057.9451-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Jia He <hejianet@gmail.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> # with cbmc[1] superpowers Acked-by: Mel Gorman <mgorman@suse.de> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The result is that two threads calling devm_memremap_pages()
simultaneously can end up colliding on pgd initialization. This leads
to crash signatures like the following where the loser of the race
initializes the wrong pgd entry:
It's because ocfs2_inode_lock() get us stale LVB in which the i_size is
not equal to the disk i_size. We mistakenly trust the LVB because the
underlaying fsdlm dlm_lock() doesn't set lkb_sbflags with
DLM_SBF_VALNOTVALID properly for us. But, why?
The current code tries to downconvert lock without DLM_LKF_VALBLK flag
to tell o2cb don't update RSB's LVB if it's a PR->NULL conversion, even
if the lock resource type needs LVB. This is not the right way for
fsdlm.
The fsdlm plugin behaves different on DLM_LKF_VALBLK, it depends on
DLM_LKF_VALBLK to decide if we care about the LVB in the LKB. If
DLM_LKF_VALBLK is not set, fsdlm will skip recovering RSB's LVB from
this lkb and set the right DLM_SBF_VALNOTVALID appropriately when node
failure happens.
The following diagram briefly illustrates how this crash happens:
RSB1 is inode metadata lock resource with LOCK_TYPE_USES_LVB;
dlm_lock(no DLM_LKF_VALBLK)
convert_lock(overwrite lkb->lkb_exflags
with no DLM_LKF_VALBLK)
RSB1: NULL RSB1: EX
reset Node2
dlm_recover_rsbs()
recover_lvb()
/* The LVB is not trustable if the node with EX fails and
* no lock >= PR is left. We should set RSB_VALNOTVALID for RSB1.
*/
if(!(kb_exflags & DLM_LKF_VALBLK)) /* This means we miss the chance to
return; * to invalid the LVB here.
*/
The 2nd round:
Node 1 Node2
RSB1(become master from recovery)
ocfs2_setattr()
ocfs2_inode_lock(NULL->EX)
/* dlm_lock() return the stale lvb without setting DLM_SBF_VALNOTVALID */
ocfs2_meta_lvb_is_trustable() return 1 /* so we don't refresh inode from disk */
ocfs2_truncate_file()
mlog_bug_on_msg(disk isize != i_size_read(inode)) /* crash! */
The fix is quite straightforward. We keep to set DLM_LKF_VALBLK flag
for dlm_lock() if the lock resource type needs LVB and the fsdlm plugin
is uesed.
Link: http://lkml.kernel.org/r/1481275846-6604-1-git-send-email-zren@suse.com Signed-off-by: Eric Ren <zren@suse.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Wed, 11 Jan 2017 00:57:30 +0000 (16:57 -0800)]
bpf: do not use KMALLOC_SHIFT_MAX
Commit c529ae4c7802 ("bpf: fix allocation warnings in bpf maps and
integer overflow") has added checks for the maximum allocateable size.
It (ab)used KMALLOC_SHIFT_MAX for that purpose.
While this is not incorrect it is not very clean because we already have
KMALLOC_MAX_SIZE for this very reason so let's change both checks to use
KMALLOC_MAX_SIZE instead.
The original motivation for using KMALLOC_SHIFT_MAX was to work around
an incorrect KMALLOC_MAX_SIZE which could lead to allocation warnings
but it is no longer needed since "slab: make sure that KMALLOC_MAX_SIZE
will fit into MAX_ORDER".
Link: http://lkml.kernel.org/r/20161220130659.16461-3-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The issue is caused by a lack of size check for the request size in
ep_write_iter which should be fixed. It, however, points to another
problem, that SLUB defines KMALLOC_MAX_SIZE too large because the its
KMALLOC_SHIFT_MAX is (MAX_ORDER + PAGE_SHIFT) which means that the
resulting page allocator request might be MAX_ORDER which is too large
(see __alloc_pages_slowpath).
The same applies to the SLOB allocator which allows even larger sizes.
Make sure that they are capped properly and never request more than
MAX_ORDER order.
Link: http://lkml.kernel.org/r/20161220130659.16461-2-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Christoph Lameter <cl@linux.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Wed, 11 Jan 2017 00:57:24 +0000 (16:57 -0800)]
dax: wrprotect pmd_t in dax_mapping_entry_mkclean
Currently dax_mapping_entry_mkclean() fails to clean and write protect
the pmd_t of a DAX PMD entry during an *sync operation. This can result
in data loss in the following sequence:
1) mmap write to DAX PMD, dirtying PMD radix tree entry and making the
pmd_t dirty and writeable
2) fsync, flushing out PMD data and cleaning the radix tree entry. We
currently fail to mark the pmd_t as clean and write protected.
3) more mmap writes to the PMD. These don't cause any page faults since
the pmd_t is dirty and writeable. The radix tree entry remains clean.
4) fsync, which fails to flush the dirty PMD data because the radix tree
entry was clean.
5) crash - dirty data that should have been fsync'd as part of 4) could
still have been in the processor cache, and is lost.
Fix this by marking the pmd_t clean and write protected in
dax_mapping_entry_mkclean(), which is called as part of the fsync
operation 2). This will cause the writes in step 3) above to generate
page faults where we'll re-dirty the PMD radix tree entry, resulting in
flushes in the fsync that happens in step 4).
Fixes: 689e5ffcb023 ("dax: clear dirty entry tags on cache flush") Link: http://lkml.kernel.org/r/1482272586-21177-3-git-send-email-ross.zwisler@linux.intel.com Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Wed, 11 Jan 2017 00:57:21 +0000 (16:57 -0800)]
mm: add follow_pte_pmd()
Patch series "Write protect DAX PMDs in *sync path".
Currently dax_mapping_entry_mkclean() fails to clean and write protect
the pmd_t of a DAX PMD entry during an *sync operation. This can result
in data loss, as detailed in patch 2.
This series is based on Dan's "libnvdimm-pending" branch, which is the
current home for Jan's "dax: Page invalidation fixes" series. You can
find a working tree here:
Similar to follow_pte(), follow_pte_pmd() allows either a PTE leaf or a
huge page PMD leaf to be found and returned.
Link: http://lkml.kernel.org/r/1482272586-21177-2-git-send-email-ross.zwisler@linux.intel.com Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Suggested-by: Dave Hansen <dave.hansen@intel.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Chinner <david@fromorbit.com> Cc: Jan Kara <jack@suse.cz> Cc: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/thp/pagecache/collapse: free the pte page table on collapse for thp page cache.
With THP page cache, when trying to build a huge page from regular pte
pages, we just clear the pmd entry. We will take another fault and at
that point we will find the huge page in the radix tree, thereby using
the huge page to complete the page fault
The second fault path will allocate the needed pgtable_t page for archs
like ppc64. So no need to deposit the same in collapse path.
Depositing them in the collapse path resulting in a pgtable_t memory
leak also giving errors like
BUG: non-zero nr_ptes on freeing mm: 3
Fixes: 90f49948417c ("mm: THP page cache support for ppc64") Link: http://lkml.kernel.org/r/20161212163428.6780-2-aneesh.kumar@linux.vnet.ibm.com Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The crux of the problem is that once we insert a 4k zero page, all
locking from then on is done in terms of that 4k zero page and any
additional threads sleeping on the empty DAX entry will never be woken.
Fix this by waking all sleepers when we replace the DAX radix tree entry
with a 4k zero page. This will allow all sleeping threads to
successfully transition from locking based on the DAX empty entry to
locking on the 4k zero page.
With the test case reported by Xiong this happens very regularly in my
test setup, with some runs resulting in 9+ threads in this deadlocked
state. With this fix I've been able to run that same test dozens of
times in a loop without issue.
Fixes: b0c9423ba5e1 ("dax: New fault locking") Link: http://lkml.kernel.org/r/1483479365-13607-1-git-send-email-ross.zwisler@linux.intel.com Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reported-by: Xiong Zhou <xzhou@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: <stable@vger.kernel.org> [4.7+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have noticed that two different descriptions for B: entries in
MAINTAINERS were merged: commit bfed6c4dcd56 ("MAINTAINERS: Add bug
tracking system location entry type") and f82e94362857 ("MAINTAINERS:
add "B:" for URI where to file bugs").
This patch keeps the description from f82e94362857. There has been a
discussion [1] about whether this more detailed description is useful
and what it exactly implies. I find it more useful and general, and the
author of bfed6c4dcd56 agreed in the end that either is fine.
Linus Torvalds [Mon, 9 Jan 2017 20:54:20 +0000 (12:54 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc4' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"amdgpu, radeon, msm, meson, tilcdc, drm fixes.
Just back online for a couple of days, gathered up the remaining fixes
pull requests.
This contains fixes for a few ARM platforms (msm, tilcdc, meson), and
one core atomic fix. The AMD pull has some new hardware support
(Polaris12) in it, but this is pretty limited to just hw enablement
and shouldn't cause any problems"
* tag 'drm-fixes-for-v4.10-rc4' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: drop verde dpm quirks
drm/radeon: drop verde dpm quirks
drm/radeon: update smc firmware selection for SI
drm/amdgpu: update si kicker smc firmware
drm/amd/powerplay: extend smu's response timeout time.
drm/amdgpu: remove static integer for uvd pp state
drm/amd/amdgpu: add Polaris12 PCI ID
drm/amdgpu/powerplay: add Polaris12 support
drm/amd/amdgpu: add Polaris12 support (v3)
MAINTAINERS: Update mailing list for radeon and amdgpu
drm/meson: Fix CVBS VDAC disable
drm/meson: Fix CVBS initialization when HDMI is configured by bootloader
drm: Clean up planes in atomic commit helper failure path
drm: tilcdc: simplify the recovery from sync lost error on rev1
drm/meson: Fix plane atomic check when no crtc for the plane
drm/msm: Verify that MSM_SUBMIT_BO_FLAGS are set
drm/msm: Put back the vaddr in submit_reloc()
drm/msm: Ensure that the hardware write pointer is valid
Linus Torvalds [Mon, 9 Jan 2017 20:50:33 +0000 (12:50 -0800)]
Merge tag 'gpio-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- move freeing of GPIO hogs to after freeing the device to get rid of a
warning state.
- a small compile warning fix
* tag 'gpio-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Move freeing of GPIO hogs before numbing of the device
gpio: mxs: remove __init annotation
1) Fix dumping of nft_quota entries, from Pablo Neira Ayuso.
2) Fix out of bounds access in nf_tables discovered by KASAN, from
Florian Westphal.
3) Fix IRQ enabling in dp83867 driver, from Grygorii Strashko.
4) Fix unicast filtering in be2net driver, from Ivan Vecera.
5) tg3_get_stats64() can race with driver close and ethtool
reconfigurations, fix from Michael Chan.
6) Fix error handling when pass limit is reached in bpf code gen on
x86. From Daniel Borkmann.
7) Don't clobber switch ops and use proper MDIO nested reads and writes
in bcm_sf2 driver, from Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
net: dsa: bcm_sf2: Utilize nested MDIO read/write
net: dsa: bcm_sf2: Do not clobber b53_switch_ops
net: stmmac: fix maxmtu assignment to be within valid range
bpf: change back to orig prog on too many passes
tg3: Fix race condition in tg3_get_stats64().
be2net: fix unicast list filling
be2net: fix accesses to unicast list
netlabel: add CALIPSO to the list of built-in protocols
vti6: fix device register to report IFLA_INFO_KIND
net: phy: dp83867: fix irq generation
amd-xgbe: Fix IRQ processing when running in single IRQ mode
sh_eth: R8A7740 supports packet shecksumming
sh_eth: fix EESIPR values for SH77{34|63}
r8169: fix the typo in the comment
nl80211: fix sched scan netlink socket owner destruction
bridge: netfilter: Fix dropping packets that moving through bridge interface
netfilter: ipt_CLUSTERIP: check duplicate config when initializing
netfilter: nft_payload: mangle ckecksum if NFT_PAYLOAD_L4CSUM_PSEUDOHDR is set
netfilter: nf_tables: fix oob access
netfilter: nft_queue: use raw_smp_processor_id()
...
We make the bcm_sf2 driver override ds->ops which points to
b53_switch_ops since b53_switch_alloc() did the assignent. This is all
well and good until a second b53 switch comes in, and ends up using the
bcm_sf2 operations. Make a proper local copy, substitute the ds->ops
pointer and then override the operations.
Fixes: 2e6c31aad854 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Sun, 8 Jan 2017 23:47:19 +0000 (09:47 +1000)]
Merge branch 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.10:
- Polaris 12 support
- Add new amd-gfx mailing list to MAINTAINERS file
- UVD clockgating fix
- SI dpm fixes
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: drop verde dpm quirks
drm/radeon: drop verde dpm quirks
drm/radeon: update smc firmware selection for SI
drm/amdgpu: update si kicker smc firmware
drm/amd/powerplay: extend smu's response timeout time.
drm/amdgpu: remove static integer for uvd pp state
drm/amd/amdgpu: add Polaris12 PCI ID
drm/amdgpu/powerplay: add Polaris12 support
drm/amd/amdgpu: add Polaris12 support (v3)
MAINTAINERS: Update mailing list for radeon and amdgpu
net: stmmac: fix maxmtu assignment to be within valid range
There is no checking valid value of maxmtu when getting it from
device tree. This resolution added the checking condition to
ensure the assignment is made within a valid range.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Sun, 8 Jan 2017 23:13:20 +0000 (09:13 +1000)]
Merge branch 'msm-fixes-4.10' of git://people.freedesktop.org/~robclark/linux into drm-fixes
A few fixes for 4.10.. the first fixes a long-standing logic bug, that
by luck (ie. size of packets written into RB for a submit) wasn't hit
on a3xx/a4xx but was causing intermittent GPU lockups on a5xx. And a
couple other robustness issues that Jordan noticed.
* 'msm-fixes-4.10' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Verify that MSM_SUBMIT_BO_FLAGS are set
drm/msm: Put back the vaddr in submit_reloc()
drm/msm: Ensure that the hardware write pointer is valid
Dave Airlie [Sun, 8 Jan 2017 23:13:13 +0000 (09:13 +1000)]
Merge tag 'meson-drm-fixes-for-4.10' of git://people.freedesktop.org/~narmstrong/linux into drm-fixes
- plan atomic check oops fix
- fix CVBS init when HDMI is configured by bootloader
- fix CVBS VDAC disable
* tag 'meson-drm-fixes-for-4.10' of git://people.freedesktop.org/~narmstrong/linux:
drm/meson: Fix CVBS VDAC disable
drm/meson: Fix CVBS initialization when HDMI is configured by bootloader
drm/meson: Fix plane atomic check when no crtc for the plane
Daniel Borkmann [Fri, 6 Jan 2017 23:26:33 +0000 (00:26 +0100)]
bpf: change back to orig prog on too many passes
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 6b1e9f887775 ("bpf, x86: add support for constant blinding") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 8 Jan 2017 19:42:04 +0000 (11:42 -0800)]
Merge tag 'usb-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 4.10-rc3. Yeah, it's a lot, an
artifact of the holiday break I think.
Lots of gadget and the usual XHCI fixups for reported issues (one day
that driver will calm down...) Also included are a bunch of usb-serial
driver fixes, and for good measure, a number of much-reported MUSB
driver issues have finally been resolved.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (72 commits)
USB: fix problems with duplicate endpoint addresses
usb: ohci-at91: use descriptor-based gpio APIs correctly
usb: storage: unusual_uas: Add JMicron JMS56x to unusual device
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
usb: musb: fix compilation warning on unused function
usb: musb: Fix trying to free already-free IRQ 4
usb: musb: dsps: implement clear_ep_rxintr() callback
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
USB: serial: ti_usb_3410_5052: fix NULL-deref at open
USB: serial: spcp8x5: fix NULL-deref at open
USB: serial: quatech2: fix sleep-while-atomic in close
USB: serial: pl2303: fix NULL-deref at open
USB: serial: oti6858: fix NULL-deref at open
USB: serial: omninet: fix NULL-derefs at open and disconnect
USB: serial: mos7840: fix misleading interrupt-URB comment
USB: serial: mos7840: remove unused write URB
USB: serial: mos7840: fix NULL-deref at open
USB: serial: mos7720: remove obsolete port initialisation
USB: serial: mos7720: fix parallel probe
...
Linus Torvalds [Sun, 8 Jan 2017 19:37:44 +0000 (11:37 -0800)]
Merge tag 'char-misc-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few small char/misc driver fixes for 4.10-rc3.
Two MEI driver fixes, and three NVMEM patches for reported issues, and
a new Hyper-V driver MAINTAINER update. Nothing major at all, all have
been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
hyper-v: Add myself as additional MAINTAINER
nvmem: fix nvmem_cell_read() return type doc
nvmem: imx-ocotp: Fix wrong register size
nvmem: qfprom: Allow single byte accesses for read/write
mei: move write cb to completion on credentials failures
mei: bus: fix mei_cldev_enable KDoc
Linus Torvalds [Sun, 8 Jan 2017 19:22:00 +0000 (11:22 -0800)]
Merge tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and IIO driver fixes for 4.10-rc3.
Most of these are minor IIO fixes of reported issues, along with one
network driver fix to resolve an issue. And a MAINTAINERS update with
a new mailing list. All of these, except the MAINTAINERS file update,
have been in linux-next with no reported issues (the MAINTAINERS patch
happened on Friday...)"
* tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: add greybus subsystem mailing list
staging: octeon: Call SET_NETDEV_DEV()
iio: accel: st_accel: fix LIS3LV02 reading and scaling
iio: common: st_sensors: fix channel data parsing
iio: max44000: correct value in illuminance_integration_time_available
iio: adc: TI_AM335X_ADC should depend on HAS_DMA
iio: bmi160: Fix time needed to sleep after command execution
iio: 104-quad-8: Fix active level mismatch for the preset enable option
iio: 104-quad-8: Fix off-by-one errors when addressing IOR
iio: 104-quad-8: Fix index control configuration
Michael Chan [Fri, 6 Jan 2017 21:18:53 +0000 (16:18 -0500)]
tg3: Fix race condition in tg3_get_stats64().
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Reported-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 6 Jan 2017 20:59:30 +0000 (21:59 +0100)]
be2net: fix unicast list filling
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Fixes: a5d22d8 be2net: replace polling with sleeping in the FW completion path Signed-off-by: Ivan Vecera <cera@cera.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Weiner [Sat, 7 Jan 2017 00:21:43 +0000 (19:21 -0500)]
mm: workingset: fix use-after-free in shadow node shrinker
Several people report seeing warnings about inconsistent radix tree
nodes followed by crashes in the workingset code, which all looked like
use-after-free access from the shadow node shrinker.
Dave Jones managed to reproduce the issue with a debug patch applied,
which confirmed that the radix tree shrinking indeed frees shadow nodes
while they are still linked to the shadow LRU:
This is the WARN_ON_ONCE(!list_empty(&node->private_list)) placed in the
inlined radix_tree_shrink().
The problem is with a08afe440d7c ("mm: workingset: move shadow entry
tracking to radix tree exceptional tracking"), which passes an update
callback into the radix tree to link and unlink shadow leaf nodes when
tree entries change, but forgot to pass the callback when reclaiming a
shadow node.
While the reclaimed shadow node itself is unlinked by the shrinker, its
deletion from the tree can cause the left-most leaf node in the tree to
be shrunk. If that happens to be a shadow node as well, we don't unlink
it from the LRU as we should.
Consider this tree, where the s are shadow entries:
root->rnode
|
[0 n]
| |
[s ] [sssss]
Now the shadow node shrinker reclaims the rightmost leaf node through
the shadow node LRU:
root->rnode
|
[0 ]
|
[s ]
Because the parent of the deleted node is the first level below the
root and has only one child in the left-most slot, the intermediate
level is shrunk and the node containing the single shadow is put in
its place:
root->rnode
|
[s ]
The shrinker again sees a single left-most slot in a first level node
and thus decides to store the shadow in root->rnode directly and free
the node - which is a leaf node on the shadow node LRU.
root->rnode
|
s
Without the update callback, the freed node remains on the shadow LRU,
where it causes later shrinker runs to crash.
Pass the node updater callback into __radix_tree_delete_node() in case
the deletion causes the left-most branch in the tree to collapse too.
Also add warnings when linked nodes are freed right away, rather than
wait for the use-after-free when the list is scanned much later.
Fixes: a08afe440d7c ("mm: workingset: move shadow entry tracking to radix tree exceptional tracking") Reported-by: Dave Chinner <david@fromorbit.com> Reported-by: Hugh Dickins <hughd@google.com> Reported-by: Andrea Arcangeli <aarcange@redhat.com> Reported-and-tested-by: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Chris Leech <cleech@redhat.com> Cc: Lee Duncan <lduncan@suse.com> Cc: Jan Kara <jack@suse.cz> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <mawilcox@linuxonhyperv.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Sat, 7 Jan 2017 23:37:31 +0000 (15:37 -0800)]
mm: stop leaking PageTables
4.10-rc loadtest (even on x86, and even without THPCache) fails with
"fork: Cannot allocate memory" or some such; and /proc/meminfo shows
PageTables growing.
Commit 90f49948417c ("mm: THP page cache support for ppc64") that got
merged in rc1 removed the freeing of an unused preallocated pagetable
after do_fault_around() has called map_pages().
This is usually a good optimization, so that the followup doesn't have
to reallocate one; but it's not sufficient to shift the freeing into
alloc_set_pte(), since there are failure cases (most commonly
VM_FAULT_RETRY) which never reach finish_fault().
Check and free it at the outer level in do_fault(), then we don't need
to worry in alloc_set_pte(), and can restore that to how it was (I
cannot find any reason to pte_free() under lock as it was doing).
And fix a separate pagetable leak, or crash, introduced by the same
change, that could only show up on some ppc64: why does do_set_pmd()'s
failure case attempt to withdraw a pagetable when it never deposited
one, at the same time overwriting (so leaking) the vmf->prealloc_pte?
Residue of an earlier implementation, perhaps? Delete it.
Fixes: 90f49948417c ("mm: THP page cache support for ppc64") Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Michael Neuling <mikey@neuling.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Balbir Singh <bsingharora@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Jan 2017 17:47:43 +0000 (09:47 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"The asm-prototypes.h file added in the last merge window results in
invalid code with CONFIG_KMEMCHECK=y. The net result is that genksyms
segfaults.
This pull request fixes the header, the genksyms fix is in my kbuild
branch for 4.11"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
asm-prototypes: Clear any CPP defines before declaring the functions
Ivan Vecera [Fri, 6 Jan 2017 19:30:02 +0000 (20:30 +0100)]
be2net: fix accesses to unicast list
Commit 957d03e "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com> Cc: Ajit Khaparde <ajit.khaparde@broadcom.com> Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Cc: Somnath Kotur <somnath.kotur@broadcom.com> Fixes: 957d03e be2net: Avoid redundant addition of mac address in HW Signed-off-by: Ivan Vecera <cera@cera.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Jan 2017 23:38:39 +0000 (15:38 -0800)]
Merge tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing particular stands out, only a few small fixes for USB-audio,
HD-audio and Firewire. The USB-audio fix is the respin of the previous
race fix after a revert due to the regression"
* tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: firewire-lib: change structure member with proper type"
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
ALSA: usb-audio: Fix irq/process data synchronization
ALSA: hda - Apply asus-mode8 fixup to ASUS X71SL
ALSA: hda - Fix up GPIO for ASUS ROG Ranger
ALSA: firewire-lib: change structure member with proper type
ALSA: firewire-tascam: Fix to handle error from initialization of stream data
ALSA: fireworks: fix asymmetric API call at unit removal
Linus Torvalds [Fri, 6 Jan 2017 23:35:27 +0000 (15:35 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Cc: Adrian Fiergolski <A.Fiergolski@gmail.com>
Junwei Zhang [Thu, 4 Aug 2016 04:54:22 +0000 (12:54 +0800)]
drm/amd/amdgpu: add Polaris12 PCI ID
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Junwei Zhang [Wed, 14 Dec 2016 20:40:48 +0000 (15:40 -0500)]
drm/amdgpu/powerplay: add Polaris12 support
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Junwei Zhang [Wed, 14 Dec 2016 20:32:28 +0000 (15:32 -0500)]
drm/amd/amdgpu: add Polaris12 support (v3)
v2: agd: squash in various fixes
v3: agd: squash in:
drm/amdgpu: remove unnecessary smc sk firmware for polaris12
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Ken Wang <Qingqing.Wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David S. Miller [Fri, 6 Jan 2017 21:26:19 +0000 (16:26 -0500)]
Merge tag 'mac80211-for-davem-2017-01-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another single fix, to correctly handle destruction of a
single netlink socket having ownership of multiple objects
(scheduled scan requests and interfaces.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Forster [Fri, 6 Jan 2017 10:27:59 +0000 (10:27 +0000)]
vti6: fix device register to report IFLA_INFO_KIND
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Fix IRQ processing when running in single IRQ mode
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 21:29:32 +0000 (00:29 +0300)]
sh_eth: R8A7740 supports packet shecksumming
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 6851aab92529 ("net: sh_eth: add support R8A7740") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 19:18:24 +0000 (22:18 +0300)]
sh_eth: fix EESIPR values for SH77{34|63}
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 8de59af2458a ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"") Fixes: 45ea9f179195 ("sh_eth: get SH77{34|63} support out of #ifdef") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Jan 2017 19:19:03 +0000 (11:19 -0800)]
Merge tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Add mtty sample driver properly into build system (Alex Williamson)
- Restore type1 mapping performance after mdev (Alex Williamson)
- Fix mdev device race (Alex Williamson)
- Cleanups to the mdev ABI used by vendor drivers (Alex Williamson)
- Build fix for old compilers (Arnd Bergmann)
- Fix sample driver error path (Dan Carpenter)
- Handle pci_iomap() error (Arvind Yadav)
- Fix mdev ioctl return type (Paul Gortmaker)
* tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio:
vfio-mdev: fix non-standard ioctl return val causing i386 build fail
vfio-pci: Handle error from pci_iomap
vfio-mdev: fix some error codes in the sample code
vfio-pci: use 32-bit comparisons for register address for gcc-4.5
vfio-mdev: Make mdev_device private and abstract interfaces
vfio-mdev: Make mdev_parent private
vfio-mdev: de-polute the namespace, rename parent_device & parent_ops
vfio-mdev: Fix remove race
vfio/type1: Restore mapping performance with mdev support
vfio-mdev: Fix mtty sample driver building
Linus Torvalds [Fri, 6 Jan 2017 18:53:21 +0000 (10:53 -0800)]
Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
Linus Torvalds [Fri, 6 Jan 2017 18:49:36 +0000 (10:49 -0800)]
Merge tag 'iommu-fixes-v4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Three fixes queued up:
- fix an issue with command buffer overflow handling in the AMD IOMMU
driver
- add an additional context entry flush to the Intel VT-d driver to
make sure any old context entry from kdump copying is flushed out
of the cache
- correct the encoding of the PASID table size in the Intel VT-d
driver"
* tag 'iommu-fixes-v4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix the left value check of cmd buffer
iommu/vt-d: Fix pasid table size encoding
iommu/vt-d: Flush old iommu caches for kdump when the device gets context mapped
Linus Torvalds [Fri, 6 Jan 2017 18:40:17 +0000 (10:40 -0800)]
Merge tag 'acpi-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a device enumeration problem related to _ADR matching and an
IOMMU initialization issue related to the DMAR table missing, remove
an excessive function call from the core ACPI code, update an error
message in the ACPI WDAT watchdog driver and add a way to work around
problems with unhandled GPE notifications.
Specifics:
- Fix a device enumeration issue leading to incorrect associations
between ACPI device objects and platform device objects
representing physical devices if the given device object has both
_ADR and _HID (Rafael Wysocki).
- Avoid passing NULL to acpi_put_table() during IOMMU initialization
which triggers a (rightful) warning from ACPICA (Rafael Wysocki).
- Drop an excessive call to acpi_dma_deconfigure() from the core code
that binds ACPI device objects to device objects representing
physical devices (Lorenzo Pieralisi).
- Update an error message in the ACPI WDAT watchdog driver to make it
provide more useful information (Mika Westerberg).
- Add a mechanism to work around issues with unhandled GPE
notifications that occur during system initialization and cannot be
prevented by means of sysfs (Lv Zheng)"
* tag 'acpi-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
ACPI / watchdog: Print out error number when device creation fails
ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding
ACPI: Drop misplaced acpi_dma_deconfigure() call from acpi_bind_one()
Linus Torvalds [Fri, 6 Jan 2017 18:37:50 +0000 (10:37 -0800)]
Merge tag 'pm-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a few issues in the intel_pstate driver, a documetation
issue, a false-positive compiler warning in the generic power domains
framework and two problems in the devfreq subsystem. They also update
the MAINTAINERS entry for devfreq and add a new "compatible" string to
the generic cpufreq-dt driver.
Specifics:
- Fix a few intel_pstate driver issues: add missing locking it two
places, avoid exposing a useless debugfs interface and keep the
attribute values in sysfs in sync (Rafael Wysocki).
- Drop confusing kernel-doc references related to power management
and ACPI from the driver API manual (Rafael Wysocki).
- Make a false-positive compiler warning in the generic power domains
framework go away (Augusto Mecking Caringi).
- Fix two initialization issues in the devfreq subsystem and update
the MAINTAINERS entry for it (Chanwoo Choi).
- Add a new "compatible" string for APM X-Gene 2 to the generic DT
cpufreq driver (Hoan Tran)"
* tag 'pm-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dt: Add support for APM X-Gene 2
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
PM / domains: Fix 'may be used uninitialized' build warning
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
So they can figure out what is the optimal number of pages
that can be contingously stitched together without fear of
bounce buffer.
We also expose an mechanism for sub-users of SWIOTLB API, such
as Xen-SWIOTLB to set the max segment value. And lastly
if swiotlb=force is set (which mandates we bounce buffer everything)
we set max_segment so at least we can bounce buffer one 4K page
instead of a giant 512KB one for which we may not have space.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reported-and-Tested-by: Juergen Gross <jgross@suse.com>
Merge branches 'pm-domains', 'pm-docs' and 'pm-devfreq'
* pm-domains:
PM / domains: Fix 'may be used uninitialized' build warning
* pm-docs:
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
* pm-devfreq:
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
* pm-cpufreq:
cpufreq: dt: Add support for APM X-Gene 2
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Linus Torvalds [Fri, 6 Jan 2017 07:17:41 +0000 (23:17 -0800)]
Merge tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for platform drivers x86:
- use brightness_set_blocking for LED-setting callbacks on Fujitsu
laptops
- fix surface3_button build errors"
* tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: use brightness_set_blocking for LED-setting callbacks
platform/x86: fix surface3_button build errors
Linus Torvalds [Fri, 6 Jan 2017 07:06:06 +0000 (23:06 -0800)]
Merge branch 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two small fixes relating to audit's use of fsnotify.
The first patch plugs a leak and the second fixes some lock
shenanigans. The patches are small and I banged on this for an
afternoon with our testsuite and didn't see anything odd"
* 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit:
audit: Fix sleep in atomic
fsnotify: Remove fsnotify_duplicate_mark()
Linus Torvalds [Thu, 5 Jan 2017 23:06:02 +0000 (15:06 -0800)]
Merge tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
fixes.
My new year's resolution is to start using signed tags for pulls. If
that feels like a déjà vu, it's ((new year's) resolution), not (new
(year's resolution))"
[ Taking this directly from Jani because Dave Airlie is only partially
connected right now. - Linus ]
* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Prevent timeline updates whilst performing reset
drm/i915: Silence allocation failure during sg_trim()
drm/i915: Don't clflush before release phys object
drm/i915: Fix oops in overlay due to frontbuffer tracking
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
drm/i915: Initialize overlay->last_flip properly
drm/i915: Move the min_pixclk[] handling to the end of readout
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
drm/i915/gvt: fix typo in cfg_space range check
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
drm/i915/gvt/kvmgt: trival: code cleanup
drm/i915/gvt/kvmgt: prevent double-release of vgpu
drm/i915/gvt/kvmgt: check returned slot for gfn
drm/i915/gvt/kvmgt: dereference the pointer within lock
drm/i915/gvt: reset the GGTT entry when vGPU created
drm/i915/gvt: fix an error in opregion handling
Alan Stern [Mon, 19 Dec 2016 17:03:41 +0000 (12:03 -0500)]
USB: fix problems with duplicate endpoint addresses
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
Linus Torvalds [Thu, 5 Jan 2017 18:36:56 +0000 (10:36 -0800)]
Merge tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Three small pin control fixes for the v4.10 series. Very little to say
about them, just driver fixes.
- one fix to the AMD pinctrl ACPI glue
- fix requests on the Meson driver
- fix bitfield widths on Samsungs Exynos 5433"
* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
pinctrl: meson: fix gpio request disabling other modes
pinctrl/amd: Set the level based on ACPI tables
Peter Rosin [Thu, 22 Dec 2016 07:43:55 +0000 (08:43 +0100)]
usb: ohci-at91: use descriptor-based gpio APIs correctly
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 9a347d0470f4 ("usb: ohci-at91: Use descriptor-based gpio APIs") Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 5 Jan 2017 18:32:16 +0000 (10:32 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
Linus Torvalds [Thu, 5 Jan 2017 18:29:40 +0000 (10:29 -0800)]
Merge tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Acked-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Jérémy Lefaure [Wed, 4 Jan 2017 00:13:52 +0000 (18:13 -0600)]
usb: musb: blackfin: add bfin_fifo_offset in bfin_ops
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: f11611f6023c ("usb: musb: Populate new IO functions for blackfin") Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jérémy Lefaure [Wed, 4 Jan 2017 00:13:49 +0000 (18:13 -0600)]
usb: musb: fix compilation warning on unused function
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+ Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu [Wed, 4 Jan 2017 00:13:46 +0000 (18:13 -0600)]
usb: musb: core: add clear_ep_rxintr() to musb_platform_ops
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
Nicholas Piggin [Thu, 5 Jan 2017 10:29:35 +0000 (20:29 +1000)]
kbuild: initramfs fix dependency checking for compressed target
When using initramfs compression, the data file compression suffix
gets quotes pulled in from Kconfig, e.g., initramfs_data.cpio".gz"
which make does not match a target and causes rebuild.
Fix this by filtering out quotes from the Kconfig string.
Fixes: d8641e4a581e ("initramfs: select builtin initram compression algorithm on KConfig instead of Makefile") Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'usb-serial-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.10-rc3
These fixes address a number of long-standing issues in various
USB-serial drivers which would lead to crashes should a malicious device
lack the expected endpoints.
Included are also a few related fixes, and a couple of unrelated ones
that were found during my survey (e.g. a memleak and a
sleep-while-atomic).
A compiler warning revealed an error-handling issue in the new f81534
driver which is also fixed.
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
Linus reported that commit 1a0483547d7b "ACPICA: Tables: Back port
acpi_get_table_with_size() and early_acpi_os_unmap_memory() from
Linux kernel" added a new warning on his desktop system:
ACPI Warning: Table ffffffff9fe6c0a0, Validation count is zero before decrement
which turns out to come from the acpi_put_table() in
detect_intel_iommu().
This happens if the DMAR table is not present in which case NULL is
passed to acpi_put_table() which doesn't check against that and
attempts to handle it regardless.
For this reason, check the pointer passed to acpi_put_table()
before invoking it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Fixes: 64c9e8124941 ("ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
James Hogan [Tue, 3 Jan 2017 17:43:00 +0000 (17:43 +0000)]
KVM: MIPS: Don't clobber CP0_Status.UX
On 64-bit kernels, MIPS KVM will clear CP0_Status.UX to prevent the
guest (running in user mode) from accessing the 64-bit memory segments.
However the previous value of CP0_Status.UX is never restored when
exiting from the guest.
If the user process uses 64-bit addressing (the n64 ABI) this can result
in address error exceptions from the kernel if it needs to deliver a
signal before returning to user mode, as the kernel will need to write a
sigframe to high user addresses on the user stack which are disallowed
by CP0_Status.UX=0.
This is fixed by explicitly setting SX and UX again when exiting from
the guest, and explicitly clearing those bits when returning to the
guest. Having the SX and UX bits set when handling guest exits (rather
than only when exiting to userland) will be helpful when we support VZ,
since we shouldn't need to directly read or write guest memory, so it
will be valid for cache management IPIs to access host user addresses.
Michal Marek [Tue, 3 Jan 2017 12:49:42 +0000 (13:49 +0100)]
asm-prototypes: Clear any CPP defines before declaring the functions
The asm-prototypes.h file is used to provide dummy function declarations
for genksyms, when processing asm files with EXPORT_SYMBOL. Make sure
that any architecture defines get out of our way. x86 currently has an
issue with memcpy on 64bit with CONFIG_KMEMCHECK=y and with
memset/__memset on 32bit:
$ cat init/test.c
#include <asm/asm-prototypes.h>
$ make -s init/test.o
In file included from ./arch/x86/include/asm/string.h:4:0,
from ./include/linux/string.h:18,
from ./include/linux/bitmap.h:8,
from ./include/linux/cpumask.h:11,
from ./arch/x86/include/asm/cpumask.h:4,
from ./arch/x86/include/asm/msr.h:10,
from ./arch/x86/include/asm/processor.h:20,
from ./arch/x86/include/asm/cpufeature.h:4,
from ./arch/x86/include/asm/thread_info.h:52,
from ./include/linux/thread_info.h:25,
from ./arch/x86/include/asm/preempt.h:6,
from ./include/linux/preempt.h:59,
from ./include/linux/spinlock.h:50,
from ./include/linux/seqlock.h:35,
from ./include/linux/time.h:5,
from ./include/uapi/linux/timex.h:56,
from ./include/linux/timex.h:56,
from ./include/linux/sched.h:19,
from ./include/linux/uaccess.h:4,
from ./arch/x86/include/asm/asm-prototypes.h:2,
from init/test.c:1:
./arch/x86/include/asm/string_64.h:52:47: error: expected declaration specifiers or ‘...’ before ‘(’ token
#define memcpy(dst, src, len) __inline_memcpy((dst), (src), (len))
./include/asm-generic/asm-prototypes.h:6:14: note: in expansion of macro ‘memcpy’
extern void *memcpy(void *, const void *, __kernel_size_t);
^
...
During real build, this manifests itself by genksyms segfaulting.
Fixes: 8825d4383ae4 ("x86/kbuild: enable modversions for symbols exported from asm") Reported-and-tested-by: Borislav Petkov <bp@alien8.de> Cc: Adam Borowski <kilobyte@angband.pl> Signed-off-by: Michal Marek <mmarek@suse.com>
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Cc: stable@vger.kernel.org Fixes: 1d2e563743c35 ("nl80211: Stop scheduled scan if netlink client disappears") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert "ALSA: firewire-lib: change structure member with proper type"
This reverts commit e6ab4345c25d084feca2fa8ee6288912a486415b. This commit
is based on a concern about value of the given parameter. It's expected
to be ORed value with some enumeration-constants, thus often it can not be
one of the enumeration-constants. I understood that this is out of
specification and causes implementation-dependent issues.
In C language specification, enumerated type can be interpreted as an
integer type, in which all of enumeration-constants in corresponding
enumerator-list can be stored. Implementations can select one of char,
signed int and unsigned int as its type, and this selection is
implementation-dependent.
In GCC, a signed integer is selected when at least one of
enumeration-constants has negative value, else an unsigned integer is
selected. This behaviour can be switched by -fshort-enums to short type.
Anyway, the type can be decided after scanning all of
enumeration-constants.
Totally, there's no rules to constrain the value of enumerated type to
be one of enumeration-constants. In short, in enumerated type, decision
of actual type for the type is the most important and
enumeration-constants are just used for the decision, thus it's permitted
to have an integer value in a range of enumeration-constants. In our case,
actual type for the type is currently deterministic to be either char or
unsigned int. Under GCC, it's unsigned int.
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
Testing EP_FLAG_RUNNING in snd_complete_urb() before running the completion
logic allows us to save a few cpu cycles by returning early, skipping the
pending urb in case the stream was stopped; the stop logic handles the urb
and sets the completion callbacks to NULL.
ALSA: usb-audio: Fix irq/process data synchronization
Commit b861f86d433 ("ALSA: usb-audio: Fix race at stopping the stream") was
incomplete causing another more severe kernel panic, so it got reverted.
This fixes both the original problem and its fallout kernel race/crash.
The original fix is to move the endpoint member NULL clearing logic inside
wait_clear_urbs() so the irq triggering the urb completion doesn't call
retire_capture/playback_urb() after the NULL clearing and generate a panic.
However this creates a new race between snd_usb_endpoint_start()'s call
to wait_clear_urbs() and the irq urb completion handler which again calls
retire_capture/playback_urb() leading to a new NULL dereference.
We keep the EP deactivation code in snd_usb_endpoint_start() because
removing it will break the EP reference counting (see [1] [2] for info),
however we don't need the "can_sleep" mechanism anymore because a new
function was introduced (snd_usb_endpoint_sync_pending_stop()) which
synchronizes pending stops and gets called inside the pcm prepare callback.
It also makes sense to remove can_sleep because it was also removed from
deactivate_urbs() signature in [3] so we benefit from more simplification.
Linus Torvalds [Thu, 5 Jan 2017 02:33:35 +0000 (18:33 -0800)]
Merge tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fixes for crashes and double-cleanup errors
- XFS maintainership handover
- fix to prevent absurdly large block reservations
- fix broken sysfs getter/setters
* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix max_retries _show and _store functions
xfs: update MAINTAINERS
xfs: fix crash and data corruption due to removal of busy COW extents
xfs: use the actual AG length when reserving blocks
xfs: fix double-cleanup when CUI recovery fails
1) stmmac_drv_probe() can race with stmmac_open() because we register
the netdevice too early. Fix from Florian Fainelli.
2) UFO handling in __ip6_append_data() and ip6_finish_output() use
different tests for deciding whether a frame will be fragmented or
not, put them in sync. Fix from Zheng Li.
3) The rtnetlink getstats handlers need to validate that the netlink
request is large enough, fix from Mathias Krause.
4) Use after free in mlx4 driver, from Jack Morgenstein.
5) Fix setting of garbage UID value in sockets during setattr() calls,
from Eric Biggers.
6) Packet drop_monitor doesn't format the netlink messages properly
such that nlmsg_next fails to work, fix from Reiter Wolfgang.
7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
Nault.
8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.
9) IGMP code doesn't reset group query timers properly, from Michal
Tesar.
10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
Alexander Duyck.
11) vxlan offload check needs to be more strict in be2net driver, from
Sabrina Dubroca.
12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
fix from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sh_eth: enable RX descriptor word 0 shift on SH7734
sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
dpaa_eth: Initialize CGR structure before init
dpaa_eth: cleanup after init_phy() failure
net: systemport: Pad packet before inserting TSB
net: systemport: Utilize skb_put_padto()
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
libcxgb: fix error check for ip6_route_output()
net: usb: asix_devices: add .reset_resume for USB PM
net: vrf: Add missing Rx counters
drop_monitor: consider inserted data in genlmsg_end
benet: stricter vxlan offloading check in be_features_check
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
net: macb: Updated resource allocation function calls to new version of API.
net: stmmac: dwmac-oxnas: use generic pm implementation
net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
net: stmmac: dwmac-oxnas: fix of-node leak
Documentation/networking: fix typo in mpls-sysctl
igmp: Make igmp group member RFC 3376 compliant
flow_dissector: Update pptp handling to avoid null pointer deref.
...
Sergei Shtylyov [Wed, 4 Jan 2017 20:10:23 +0000 (23:10 +0300)]
sh_eth: enable RX descriptor word 0 shift on SH7734
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: ac382cffde13 ("net: sh_eth: Add support SH7734") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Wed, 4 Jan 2017 20:38:16 +0000 (21:38 +0100)]
ALSA: hda - Apply asus-mode8 fixup to ASUS X71SL
Although the old quirk table showed ASUS X71SL with ALC663 codec being
compatible with asus-mode3 fixup, the bugzilla reporter explained that
asus-model8 fits better for the dual headphone controls. So be it.