Thierry Reding [Mon, 28 Oct 2019 12:37:08 +0000 (13:37 +0100)]
drm/tegra: Simplify IOMMU group selection
All the devices that make up the DRM device are now part of the same
IOMMU group. This simplifies the handling of the IOMMU attachment and
also avoids exhausting the number of IOMMUs available on early Tegra
SoC generations.
Thierry Reding [Mon, 28 Oct 2019 12:16:10 +0000 (13:16 +0100)]
drm/tegra: Do not use ->load() and ->unload() callbacks
The ->load() and ->unload() drivers are midlayers and should be avoided
in modern drivers. Fix this by moving the code into the driver ->probe()
and ->remove() implementations, respectively.
v2: kick out conflicting framebuffers before initializing fbdev
v3: rebase onto drm/tegra/for-next
Thierry Reding [Mon, 24 Jun 2019 13:13:16 +0000 (15:13 +0200)]
drm/tegra: sor: Extract common audio enabling code
The code to enable audio support is split into two parts, one being
generic for the SOR and another part that is specific whether the SOR is
in HDMI mode or in DP mode. Split out the common part in preparation for
reusing the code in DP mode.
When the SOR is disabled in DP mode as part of an unplug event, do not
attempt to power the DP link down. Powering down the link requires the
DPAUX to transmit AUX messages which only works if there's a connected
sink.
Thierry Reding [Thu, 27 Jun 2019 10:34:57 +0000 (12:34 +0200)]
drm/tegra: sor: Unify eDP and DP support
The SOR0 on Tegra210 does, contrary to what was previously assumed, in
fact support DisplayPort. The difference between SOR0 and SOR1 is that
the latter supports audio and HDCP over DP, whereas the former doesn't.
The code for eDP and DP is now almost identical and the differences can
easily be parameterized based on the presence of a panel. There is no
need any longer to duplicate the code.
The correct I/O pad needs to be powered up before DP can be used. Make
sure the correct default is set for Tegra generations where the I/O pad
cannot be derived from the SOR instance.
Thierry Reding [Thu, 27 Jun 2019 10:29:56 +0000 (12:29 +0200)]
drm/tegra: sor: Deduplicate connector type detection code
The connector type detection code is duplicated in two places. Keeping
both places in sync is an extra maintenance burden that can be avoided
by comparing the connector type operations that are set upon the first
detection.
Thierry Reding [Mon, 24 Jun 2019 15:06:34 +0000 (17:06 +0200)]
drm/tegra: sor: Implement pad clock for all SOR instances
So far the pad clock was only needed on the second SOR instance. The
clock does exist for all SOR instances, though, so make sure it is
always implemented. This prepares for further unification of the code
in subsequent patches.
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Thierry Reding [Thu, 1 Feb 2018 16:47:07 +0000 (17:47 +0100)]
drm/tegra: sor: Filter eDP rates
The SOR found on Tegra SoCs does not support all the rates potentially
advertised by eDP 1.4. Make sure that the rates that are not supported
are filtered out.
This is necessary for the output abstraction to retrieve a list of valid
modes from the EDID of a connected panel/monitor. This will be useful in
conjunction with DisplayPort support that will be added in a subsequent
patch, so that the driver can read EDID via the AUX channel.
Thierry Reding [Tue, 15 Oct 2019 12:57:42 +0000 (14:57 +0200)]
drm/tegra: sor: Use DP link training helpers
Make use of the DP link training helpers to implement full and fast link
training. While at it, refactor some of the code and remove various code
sequences that are not necessary.
This helper chooses an appropriate configuration, according to the
bitrate requirements of the video mode and the capabilities of the
DisplayPort sink.
Thierry Reding [Thu, 3 Dec 2015 12:07:43 +0000 (13:07 +0100)]
drm/tegra: dp: Read fast training capability from link
While probing the DisplayPort link, query the fast training capability.
If supported, drivers can use the fast link training sequence instead of
the more involved full link training sequence.
Thierry Reding [Thu, 3 Dec 2015 11:45:45 +0000 (12:45 +0100)]
drm/tegra: dp: Turn link capabilities into booleans
Rather than storing capabilities as flags in an integer, use a separate
boolean per capability. This simplifies the code that checks for these
capabilities.
Thierry Reding [Thu, 27 Jun 2019 10:24:41 +0000 (12:24 +0200)]
drm/tegra: dpaux: Parameterize CMH, DRVZ and DRVI
The CMH, DRVZ and DRVI values vary depending on the SoC generation. Move
them into SoC specific structures so that DT compatible string matching
can be used to select the right parameters and write them to hardware at
the right time.
Thierry Reding [Mon, 24 Jun 2019 11:30:24 +0000 (13:30 +0200)]
drm/tegra: dpaux: Fix crash if VDD supply is absent
In order to properly make the VDD supply optional, all accesses to the
regulator need to be ignored, because the regulator core doesn't treat
NULL special.
Thierry Reding [Mon, 3 Aug 2015 12:08:34 +0000 (14:08 +0200)]
drm/tegra: dpaux: Support monitor hotplugging
The dpaux driver has a quirk built-in that will delay initialization of
the display driver for a short while, trying to detect an eDP panel. The
reason for this quirk is that the panel may not report as connected
until after the display driver has initialized, at which point the fbdev
emulation will have fallen back to 1024x768 as default resolution, which
will likely not be the eDP panel's native resolution.
With upcoming DisplayPort support, the code needs to be able to cope
with hotpluggable monitors as well. Waiting for a panel to show up is no
longer going to work because the monitor may not be attached on boot. If
the output runs in DisplayPort mode, skip waiting for the panel to show
up.
Thierry Reding [Fri, 8 Jun 2018 13:00:05 +0000 (15:00 +0200)]
drm/tegra: gem: Use sg_alloc_table_from_pages()
Instead of manually creating the SG table for a discontiguous buffer,
use the existing sg_alloc_table_from_pages(). Note that this is not safe
to be used with the ARM DMA/IOMMU integration code because that will not
ensure that the whole buffer is mapped contiguously. Depending on the
size of the individual entries the mapping may end up containing holes
to ensure alignment.
However, we only ever use these buffers with explicit IOMMU API usage
and know how to avoid these holes.
Thierry Reding [Mon, 4 Jun 2018 15:36:50 +0000 (17:36 +0200)]
drm/tegra: gem: Rename paddr -> iova
The address can refer to either physical memory or IO virtual memory.
If referring to IO virtual memory, there will always be an associated
physical memory address. Rename this variable to "iova" to clarify in
all cases that this is the IO virtual memory, which in the absence of
an IOMMU is identical to the physical address.
drm/tegra: Inherit device DMA parameters from host1x
The display controllers and VIC don't have any limitations on the
DMA segment size. Inherit the DMA parameters from the parent device,
which also doesn't have any such limitations.
Thierry Reding [Mon, 18 Jun 2018 12:01:51 +0000 (14:01 +0200)]
gpu: host1x: Request channels for clients, not devices
A struct device doesn't carry much information that a channel might be
interested in, but the client very much does. Request channels for the
clients rather than their parent devices and store a pointer to them
in order to have that information available when needed.
It's technically not required to explicitly initialize the fields that
will be zero by default, but it's easier to read these structures if
they are all initialized uniformly.
Commit Fixes: b9f8b09ce256 ("drm/tegra: Setup shared IOMMU domain after
initialization") changed the initialization order of the IOMMU related
bits but didn't update the cleanup path accordingly. This asymmetry can
cause failures during error recovery.
Thierry Reding [Wed, 20 Feb 2019 09:03:46 +0000 (10:03 +0100)]
drm/tegra: sor: Move register programming out of ->init()
The hardware is not guaranteed to be enabled during execution of the
tegra_sor_init() function, which can lead to a crash on some Tegra SoCs.
Fix this by moving all register programming into code that is guaranteed
to only be executed when the hardware is enabled.
Thierry Reding [Mon, 21 Oct 2019 14:34:37 +0000 (16:34 +0200)]
drm/tegra: Move drm_dp_link helpers to Tegra DRM
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. After
all other drivers have been converted not to use these helpers anymore,
move these helpers into the last remaining user: Tegra DRM.
If at some point these helpers are deemed more widely useful, they can
be moved out into the DRM DP helpers again.
Thierry Reding [Mon, 21 Oct 2019 14:34:36 +0000 (16:34 +0200)]
drm/rockchip: Avoid drm_dp_link helpers
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. Start
pushing the equivalent code into individual drivers to ultimately remove
them.
Thierry Reding [Mon, 21 Oct 2019 14:34:35 +0000 (16:34 +0200)]
drm/msm: edp: Avoid drm_dp_link helpers
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. Start
pushing the equivalent code into individual drivers to ultimately remove
them.
Thierry Reding [Mon, 21 Oct 2019 14:34:33 +0000 (16:34 +0200)]
drm/bridge: tc358767: Avoid drm_dp_link helpers
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. Start
pushing the equivalent code into individual drivers to ultimately remove
them.
During the discussion of patches that enhance the drm_dp_link helpers it
was concluded that these helpers aren't very useful to begin with. Start
pushing the equivalent code into individual drivers to ultimately remove
them.
v4: use bulk DPCD writes if possible (Daniel Vetter)
Thierry Reding [Mon, 21 Oct 2019 14:34:31 +0000 (16:34 +0200)]
drm/dp: Add helper to get post-cursor adjustments
If the transmitter supports pre-emphasis post cursor2 the sink will
request adjustments in a similar way to how it requests adjustments to
the voltage swing and pre-emphasis settings.
Add a helper to extract these adjustments on a per-lane basis from the
DPCD link status.
Thierry Reding [Mon, 21 Oct 2019 14:34:30 +0000 (16:34 +0200)]
drm/dp: Do not busy-loop during link training
Use microsecond sleeps for the clock recovery and channel equalization
delays during link training. The duration of these delays can be from
100 us up to 16 ms. It is rude to busy-loop for that amount of time.
While at it, also convert to standard coding style by putting the
opening braces in a function definition on a new line. Also switch to
using an unsigned int for the AUX read interval to match the data type
of the parameters to usleep_range().
v2: use correct multiplier for training delays (Philipp Zabel)
v3: clarify data type change in commit message
Thierry Reding [Mon, 21 Oct 2019 14:34:26 +0000 (16:34 +0200)]
drm/dp: Remove a gratuituous blank line
It's idiomatic to check the return value of a function call immediately
after the function call, without any blank lines in between, to make it
more obvious that the two lines belong together.
Daniel Vetter [Tue, 22 Oct 2019 15:25:30 +0000 (17:25 +0200)]
drm/todo: Add levels
Should help new people pick suitable tasks.
Cc: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Sean Paul <sean@poorly.run> Reviewed-by: Sean Paul <sean@poorly.run> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191022152530.22038-2-daniel.vetter@ffwll.ch
Daniel Vetter [Tue, 22 Oct 2019 16:37:17 +0000 (18:37 +0200)]
drm/doc: Drop misleading comment on drm_mode_config_cleanup
This is not something we'll fix, because failing to clean up stuff (or
doing it in the wrong order) is a driver bug. The offending FIXME goes
all the way back to the original modeset merge.
including a comment blaming drivers on this. Right thing to do is most
likely drm_atomic_helper_shutdown plus making sure that
drm_mode_config_cleanup is not called too early (i.e. not in driver
unload, but only in the final drm_device release callback).
Mihail Atanassov [Mon, 21 Oct 2019 15:01:56 +0000 (15:01 +0000)]
MAINTAINERS: Add Mihail to Komeda DRM driver
I'll be the main point of contact.
Cc: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Acked-by: Sean Paul <sean@poorly.run> Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com> Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191021150123.19570-1-mihail.atanassov@arm.com
Wambui Karuga [Sat, 19 Oct 2019 07:18:40 +0000 (10:18 +0300)]
drm: remove unnecessary return variable
Remove unnecessary variable `ret` in drm_dp_atomic_find_vcpi_slots()
only used to hold the function return value and have the function
return the value directly.
Issue found by coccinelle:
@@
local idexpression ret;
expression e;
@@
Kangjie Lu [Fri, 18 Oct 2019 04:41:50 +0000 (23:41 -0500)]
drm/gma500: fix memory disclosures due to uninitialized bytes
"clock" may be copied to "best_clock". Initializing best_clock
is not sufficient. The fix initializes clock as well to avoid
memory disclosures and informaiton leaks.
Kangjie Lu [Fri, 18 Oct 2019 04:29:53 +0000 (23:29 -0500)]
gma/gma500: fix a memory disclosure bug due to uninitialized bytes
`best_clock` is an object that may be sent out. Object `clock`
contains uninitialized bytes that are copied to `best_clock`,
which leads to memory disclosure and information leak.
- drm-next backmerge for HDR DP changes
https://lists.freedesktop.org/archives/dri-devel/2019-September/236453.html
Driver Changes:
- Add DC3CO sleep state for Tigerlake (Anshuman)
- Tigerlake BCS engine support engine relative MMIO (Daniele)
- Simplify the Tigerlake LRC register list for !RCS (Daniele)
- Read SAGV block time from PCODE on Tigerlake (James)
- Add 12 missing Tigerlake workarounds (Mika)
- Enable DDI/Port G for Tigerlake (Khaled)
- Avoid hang in tsg,vfe units by keeping l3 clocks ICL+(Mika)
- Fix Bugzilla #111966: Favor last VBT child device (Ville)
- Fix blue/black screen on boot due to broken gamma (Swati)
- Add support of BT.2020 Colorimetry to DP MSA (Gwan-gyeong)
- Attach colorspace property to DP connector (Gwan-gyeong)
- Attach HDR metadata property to DP connector (Gwan-gyeong)
- Base intel_memory_region support prep for local memory (Matt A)
- Introduce Jasper Lake PCH (Matt R)
- Support multiple GPUs in PMU (Tvrtko)
- Fix MST oops due to MSA changes (Ville)
- Refuse modes with hdisplay==4096 on pre-HSW DP (Ville)
- Correct the PCH type in irq postinstall for JSP (Vivek)
- Save Master transcoder in slave's crtc_state for Transcoder Port Sync (Manasi)
- Enable TRANSCODER PORT SYNC for tiled displays across separate ports (Manasi)
- HW state readout for transcoder port sync config (Manasi)
- Enable master-slaves in trans port sync (Manasi)
- In port sync mode disable slaves first then master (Manasi)
- Fix port checks for MST support on gen >= 11 (Lucas)
- Flush submission tasklet before waiting/retiring (Chris)
- Flush tasklet submission before sleeping on i915_request_wait (Chris)
- Object pin reference counting fixes (Chris, Matt A)
- Clear semaphore immediately upon ELSP promotion (Chris)
- Child device size remains unchanged through VBT 229 (Matt R)
- Restore dropped 'interruptible' flag on retiring requests (Chris)
- Treat a busy timeline as 'active' while waiting (Chris)
- Clean up struct_mutex from perf (Chris)
- Update locking around execlists->active (Chris)
- Mark up expected execlist state during reset (Chris)
- Remove cursor use of properties for coordinates (Maarten)
- Only mark incomplete requests as -EIO on cancelling (Chris)
- Add an rcu_barrier option to i915_drop_caches (Chris)
- Replace perf global wakeref tracking with engine-pm (Chris)
- Prevent merging requests with conflicting flags (Chris)
- Allow for CS OA configs to be created lazily (Lionel)
- Implement active wait for noa configurations (Lionel)
- Execute OA configuration from command stream (Lionel)
- Prefer using the pinned_ctx for emitting delays on config (Chris)
- Port C's hotplug interrupt is associated with TC1 bits (Vivek, Matt R)
- Extend program of VSC Header and DB for Colorimetry Format (Gwan-gyeong)
- Fine-tune timeslicing of contexts (Chris)
- Do initial mocs configuration directly (Chris)
- Fix uninitialized variable on PMU error path (Tvrtko)
- Don't disable interrupts independently of the locking (Sebastian)
- Eliminate struct_mutext from GVT (Chris)
- Move perf types to their own header (Lionel)
- Drop list of perf streams (always size 1) (Lionel)
- Store the perf associated engine of a stream (Lionel)
- Make array hw_engine_mask static (Colin)
- Prefer shortest path to RPM/perf/GT instead of dev_priv (Chris, Tvrtko)
- Virtual request submission fixes (Chris)
- Selftest/CI improvements (Chris)
- Fix Kconfig indentation (Krzysztof)
- Give engine->kernel_context distinct timeline lock classes (Chris)
- Fix null pointer deref on selftest error path (Colin)
- Select DPLL's via mask (Matt R)
- Introduce and use intel_atomic_crtc_state_for_each_plane_state (Maarten)
- Use intel_plane_state in prepare and cleanup plane_fb (Maarten)
- Remove begin/finish_crtc_commit (Maarten)
- Move SAGV block time to dev_priv (James)
- Avoid polluting the i915_oa_config with error pointers (Chris)
- Squelch display kerneldoc warnings (Chris)
- Assert tasklet is locked for process_csb() (Chris)
- Switch to using DP_MSA_MISC_* defines (Ville)
- Stop using drm_atomic_helper_check_planes() (Ville)
- Make .modeset_calc_cdclk() mandatory (Ville)
- Use drm_rect_translate_to()/drm_rect_init() (Ville)
- Refactor timestamping constants update (Ville)
- Switch intel_legacy_cursor_update() to intel_ types (Ville)
- Prepare the connector/encoder mask readout for hw vs. uapi state split (Ville)
- Prepare the mode readout for hw vs. uapi state split (Ville)
- Move swizzle_bit under i915_ggtt (Chris)
- Improve microcontrollers documentation (Daniele)
- Move the cursor rotation handling into intel_cursor_check_surface() (Ville)
- Cleanups to pipe code (Ville)
- Shrink eDRAM ways/sets arrays for code size (Ville)
- Cleanups to HDCP2 timeout code (Ville)
- Restore full symmetry in i915_driver_modeset_probe/remove (Janusz)
- Simplify setting of ddi_io_power_domain (Lucas)
- Add pipe id/name to pipe mismatch logs (Lucas)
- Prettify MST debug message (Lucas)
- Extract GT ring management to separate files (Andi)
Andi Shyti [Sun, 20 Oct 2019 18:41:39 +0000 (19:41 +0100)]
drm/i915: Extract GT ring management
Although the ring management is much smaller compared to the other GT
power management functions, continue the theme of extracting it out of
the huge intel_pm.c for maintenance.
Linus Torvalds [Sun, 20 Oct 2019 16:36:57 +0000 (12:36 -0400)]
Merge tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix a bashism of setlocalversion
- do not use the too new --sort option of tar
* tag 'kbuild-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: substituting --sort in archive creation
scripts: setlocalversion: fix a bashism
kbuild: update comment about KBUILD_ALLDIRS
Linus Torvalds [Sun, 20 Oct 2019 10:31:14 +0000 (06:31 -0400)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Prevent a NULL pointer dereference in the X2APIC code in case of a
CPU hotplug failure.
- Prevent boot failures on HP superdome machines by invalidating the
level2 kernel pagetable entries outside of the kernel area as
invalid so BIOS reserved space won't be touched unintentionally.
Also ensure that memory holes are rounded up to the next PMD
boundary correctly.
- Enable X2APIC support on Hyper-V to prevent boot failures.
- Set the paravirt name when running on Hyper-V for consistency
- Move a function under the appropriate ifdef guard to prevent build
warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/acpi: Move get_cmdline_acpi_rsdp() under #ifdef guard
x86/hyperv: Set pv_info.name to "Hyper-V"
x86/apic/x2apic: Fix a NULL pointer deref when handling a dying cpu
x86/hyperv: Make vapic support x2apic mode
x86/boot/64: Round memory hole size up to next PMD page
x86/boot/64: Make level2_kernel_pgt pages invalid outside kernel area
projects / kernel.git / log