PCI passthrough to VMs does not work with AMD FCH AHCI adapters: the guest
OS fails to correctly probe devices attached to the controller due to FIS
communication failures:
On surprise removal, pciehp_unconfigure_device() and acpiphp's
trim_stale_devices() call pci_dev_set_disconnected() to mark removed
devices as permanently offline. Thereby, the PCI core and drivers know
to skip device accesses.
However pci_dev_set_disconnected() takes the device_lock and thus waits for
a concurrent driver bind or unbind to complete. As a result, the driver's
->probe and ->remove hooks have no chance to learn that the device is gone.
That doesn't make any sense, so drop the device_lock and instead use atomic
xchg() and cmpxchg() operations to update the device state.
As a byproduct, an AB-BA deadlock reported by Anatoli is fixed which occurs
on surprise removal with AER concurrently performing a bus reset.
AER bus reset:
INFO: task irq/26-aerdrv:95 blocked for more than 120 seconds.
Tainted: G W 6.2.0-rc3-custom-norework-jan11+
schedule
rwsem_down_write_slowpath
down_write_nested
pciehp_reset_slot # acquires reset_lock
pci_reset_hotplug_slot
pci_slot_reset # acquires device_lock
pci_bus_error_reset
aer_root_reset
pcie_do_recovery
aer_process_err_devices
aer_isr
pciehp surprise removal:
INFO: task irq/26-pciehp:96 blocked for more than 120 seconds.
Tainted: G W 6.2.0-rc3-custom-norework-jan11+
schedule_preempt_disabled
__mutex_lock
mutex_lock_nested
pci_dev_set_disconnected # acquires device_lock
pci_walk_bus
pciehp_unconfigure_device
pciehp_disable_slot
pciehp_handle_presence_or_link_change
pciehp_ist # acquires reset_lock
However, pci_bridge_wait_for_secondary_bus() bails out if the bridge_d3
flag is not set. That flag indicates whether a bridge is allowed to
suspend to D3cold at *runtime*.
Hence *no* delay is observed on resume from system sleep if runtime
D3cold is forbidden. That doesn't make any sense, so drop the bridge_d3
check from pci_bridge_wait_for_secondary_bus().
The purpose of the bridge_d3 check was probably to avoid delays if a
bridge remained in D0 during suspend. However the sole caller of
pci_bridge_wait_for_secondary_bus(), pci_pm_bridge_power_up_actions(),
is only invoked if the previous power state was D3cold. Hence the
additional bridge_d3 check seems superfluous.
Fixes: 34cd7c4bc4b5 ("PCI/PM: Add missing link delays required by the PCIe spec") Link: https://lore.kernel.org/r/eb37fa345285ec8bacabbf06b020b803f77bdd3d.1673769517.git.lukas@wunner.de Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Cc: stable@vger.kernel.org # v5.5+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: slab-out-of-bounds in ses_enclosure_data_process+0x949/0xe30 [ses]
Read of size 1 at addr ffff88a1b043a451 by task systemd-udevd/3271
Checking after (and before in next loop) addl_desc_ptr[1] is sufficient, we
expect the size to be sanitized before first access to addl_desc_ptr[1].
Make sure we don't walk beyond end of page.
Link: https://lore.kernel.org/r/20230202162451.15346-2-thenzl@redhat.com Cc: stable@vger.kernel.org Signed-off-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An enclosure with no components can't usefully be operated by the driver
(since effectively it has nothing to manage), so report the problem and
don't attach. Not attaching also fixes an oops which could occur if the
driver tries to manage a zero component enclosure.
[mkp: Switched to KERN_WARNING since this scenario is common]
Link: https://lore.kernel.org/r/c5deac044ac409e32d9ad9968ce0dcbc996bfc7a.camel@linux.ibm.com Cc: stable@vger.kernel.org Reported-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If after an adapter reset the appearance of link is not recovered, the
devices are not rediscovered. This is result of a race condition between
adapter reset (abort_isp) and the topology scan. During adapter reset, the
ABORT_ISP_ACTIVE flag is set. Topology scan usually occurred after adapter
reset. In this case, the topology scan came earlier than usual where it
ran into problem due to ABORT_ISP_ACTIVE flag was still set.
kernel: qla2xxx [0000:13:00.0]-1005:1: Cmd 0x6a aborted with timeout since ISP Abort is pending
kernel: qla2xxx [0000:13:00.0]-28a0:1: MBX_GET_PORT_NAME failed, No FL Port.
kernel: qla2xxx [0000:13:00.0]-286b:1: qla2x00_configure_loop: exiting normally. local port wwpn 51402ec0123d9a80 id 012300)
kernel: qla2xxx [0000:13:00.0]-8017:1: ADAPTER RESET SUCCEEDED nexus=1:0:15.
Allow adapter reset to complete before any scan can start.
User experienced symptoms of adapter failure in NPIV environment. NPIV
hosts were allowed to trigger chip reset back to back due to NPIV link
state being slow to come online.
Fix link failure in NPIV environment by removing NPIV host from directly
being able to perform chip reset.
kernel: qla2xxx [0000:04:00.1]-6009:261: Loop down - aborting ISP.
kernel: qla2xxx [0000:04:00.1]-6009:262: Loop down - aborting ISP.
kernel: qla2xxx [0000:04:00.1]-6009:281: Loop down - aborting ISP.
kernel: qla2xxx [0000:04:00.1]-6009:285: Loop down - aborting ISP
There is a disconnect between the run_command function and the
wait_for_input. The wait_for_input has a default timeout of 2 minutes. But
if that happens, the run_command loop will exit out to the waitpid() of
the executing command. This fails in that it no longer monitors the
command, and also, the ssh to the test box can hang when its finished, as
it's waiting for the pipe it's writing to to flush, but the loop that
reads that pipe has already exited, leaving the command stuck, and the
test hangs.
Instead, make the default "wait_for_input" of the run_command infinite,
and allow the user to override it if they want with a default timeout
option "RUN_TIMEOUT".
But this fixes the hang that happens when the pipe is full and the ssh
session never exits.
Cc: stable@vger.kernel.org Fixes: 943e4212751c5 ("ktest: Add timeout to ssh command") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the "reboot" command, it does a check of the machine to see if it is
still alive with a simple "ssh echo" command. If it fails, it will assume
that a normal "ssh reboot" is not possible and force a power cycle.
In this case, the "start_monitor" is executed, but the "end_monitor" is
not, and this causes the screen will not be given back to the console. That
is, after the test, a "reset" command needs to be performed, as "echo" is
turned off.
Cc: stable@vger.kernel.org Fixes: aa8896990f75d ("ktest.pl: Powercycle the box on reboot if no connection can be made") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When monitoring the console output, the stdout is being redirected to do
so. If Ctrl^C is hit during this mode, the stdout is not back to the
console, the user does not see anything they type (no echo).
Add "end_monitor" to the SIGINT interrupt handler to give back the console
on Ctrl^C.
Cc: stable@vger.kernel.org Fixes: a61f9ef369d75 ("ktest: Give console process a dedicated tty") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel build regression with LLVM was reported here:
https://lore.kernel.org/all/Y1GCYXGtEVZbcv%2F5@dev-arch.thelio-3990X/ with
commit fbd8afaa6a1e ("mm: align larger anonymous mappings on THP
boundaries"). And the commit fbd8afaa6a1e was reverted.
It turned out the regression is related with madvise(MADV_DONTNEED)
was used by ld.lld. But with none PMD_SIZE aligned parameter len.
trace-bpfcc captured:
531607 531732 ld.lld do_madvise.part.0 start: 0x7feca9000000, len: 0x7fb000, behavior: 0x4
531607 531793 ld.lld do_madvise.part.0 start: 0x7fec86a00000, len: 0x7fb000, behavior: 0x4
If the underneath physical page is THP, the madvise(MADV_DONTNEED) can
trigger split_queue_lock contention raised significantly. perf showed
following data:
14.85% 0.00% ld.lld [kernel.kallsyms] [k]
entry_SYSCALL_64_after_hwframe
11.52%
entry_SYSCALL_64_after_hwframe
do_syscall_64
__x64_sys_madvise
do_madvise.part.0
zap_page_range
unmap_single_vma
unmap_page_range
page_remove_rmap
deferred_split_huge_page
__lock_text_start
native_queued_spin_lock_slowpath
If THP can't be removed from rmap as whole THP, partial THP will be
removed from rmap by removing sub-pages from rmap. Even the THP head page
is added to deferred queue already, the split_queue_lock will be acquired
and check whether the THP head page is in the queue already. Thus, the
contention of split_queue_lock is raised.
Before acquire split_queue_lock, check and bail out early if the THP
head page is in the queue already. The checking without holding
split_queue_lock could race with deferred_split_scan, but it doesn't
impact the correctness here.
Test result of building kernel with ld.lld:
commit 0ab794c5f4ca (parent commit of fbd8afaa6a1e):
time -f "\t%E real,\t%U user,\t%S sys" make LD=ld.lld -skj96 allmodconfig all
6:07.99 real, 26367.77 user, 5063.35 sys
commit fbd8afaa6a1e:
time -f "\t%E real,\t%U user,\t%S sys" make LD=ld.lld -skj96 allmodconfig all
7:22.15 real, 26235.03 user, 12504.55 sys
commit fbd8afaa6a1e with the fixing patch:
time -f "\t%E real,\t%U user,\t%S sys" make LD=ld.lld -skj96 allmodconfig all
6:08.49 real, 26520.15 user, 5047.91 sys
Link: https://lkml.kernel.org/r/20221223135207.2275317-1-fengwei.yin@intel.com Signed-off-by: Yin Fengwei <fengwei.yin@intel.com> Tested-by: Nathan Chancellor <nathan@kernel.org> Acked-by: David Rientjes <rientjes@google.com> Reviewed-by: "Huang, Ying" <ying.huang@intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Rik van Riel <riel@surriel.com> Cc: Xing Zhengjun <zhengjun.xing@linux.intel.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Charge moving mode in cgroup1 allows memory to follow tasks as they
migrate between cgroups. This is, and always has been, a questionable
thing to do - for several reasons.
First, it's expensive. Pages need to be identified, locked and isolated
from various MM operations, and reassigned, one by one.
Second, it's unreliable. Once pages are charged to a cgroup, there isn't
always a clear owner task anymore. Cache isn't moved at all, for example.
Mapped memory is moved - but if trylocking or isolating a page fails,
it's arbitrarily left behind. Frequent moving between domains may leave a
task's memory scattered all over the place.
Third, it isn't really needed. Launcher tasks can kick off workload tasks
directly in their target cgroup. Using dedicated per-workload groups
allows fine-grained policy adjustments - no need to move tasks and their
physical pages between control domains. The feature was never
forward-ported to cgroup2, and it hasn't been missed.
Despite it being a niche usecase, the maintenance overhead of supporting
it is enormous. Because pages are moved while they are live and subject
to various MM operations, the synchronization rules are complicated.
There are lock_page_memcg() in MM and FS code, which non-cgroup people
don't understand. In some cases we've been able to shift code and cgroup
API calls around such that we can rely on native locking as much as
possible. But that's fragile, and sometimes we need to hold MM locks for
longer than we otherwise would (pte lock e.g.).
Mark the feature deprecated. Hopefully we can remove it soon.
And backport into -stable kernels so that people who develop against
earlier kernels are warned about this deprecation as early as possible.
[akpm@linux-foundation.org: fix memory.rst underlining] Link: https://lkml.kernel.org/r/Y5COd+qXwk/S+n8N@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Shakeel Butt <shakeelb@google.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of syscall_get_nr on mips used to ignore the task
argument and return the syscall number of the calling thread instead of
the target thread.
The bug was exposed to user space by commit 581c64a5d518f ("ptrace: add
PTRACE_GET_SYSCALL_INFO request") and detected by strace test suite.
Link: https://github.com/strace/strace/issues/235 Fixes: ec8f76e2e5f1 ("MIPS: Fix syscall_get_nr for the syscall exit tracing.") Cc: <stable@vger.kernel.org> # v3.19+ Co-developed-by: Dmitry V. Levin <ldv@strace.io> Signed-off-by: Dmitry V. Levin <ldv@strace.io> Signed-off-by: Elvira Khabirova <lineprinter0@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Type 3 instruction fault (FPU insn with FPU disabled) is handled
by quietly enabling FPU and returning. Which is fine, except that
we need to do that both for fault in userland and in the kernel;
the latter *can* legitimately happen - all it takes is this:
- call_pal CLRFEN to clear "FPU enabled" flag and arrange for
a signal delivery (SIGSEGV in this case).
Fixed by moving the handling of type 3 into the common part of
do_entIF(), before we check for kernel vs. user mode.
Incidentally, the check for kernel mode is unidiomatic; the normal
way to do that is !user_mode(regs). The difference is that
the open-coded variant treats any of bits 63..3 of regs->ps being
set as "it's user mode" while the normal approach is to check just
the bit 3. PS is a 4-bit register and regs->ps always will have
bits 63..4 clear, so the open-coded variant here is actually equivalent
to !user_mode(regs). Harder to follow, though...
Cc: stable@vger.kernel.org Reviewed-by: Richard Henderson <rth@twiddle.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If getting an ID or setting up a work queue in rbd_dev_create() fails,
use-after-free on rbd_dev->rbd_client, rbd_dev->spec and rbd_dev->opts
is triggered in do_rbd_add(). The root cause is that the ownership of
these structures is transfered to rbd_dev prematurely and they all end
up getting freed when rbd_dev_create() calls rbd_dev_free() prior to
returning to do_rbd_add().
Found by Linux Verification Center (linuxtesting.org) with SVACE, an
incomplete patch submitted by Natalia Petrova <n.petrova@fintech.ru>.
TMU node uses 0 as thermal-sensor-cells, thus thermal zone referencing
it must not have an argument to phandle. Since thermal-sensors property
is already defined in included exynosi5410.dtsi, drop it from
exynos5410-odroidxu.dts to fix the error and remoev redundancy.
Fixes: 10906c0b2f89 ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board") Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20230209105841.779596-4-krzysztof.kozlowski@linaro.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we need to zero some range on a block device, the function
__blkdev_issue_zero_pages submits a write bio with the bio vector pointing
to the zero page. If we use dm-flakey with corrupt bio writes option, it
will corrupt the content of the zero page which results in crashes of
various userspace programs. Glibc assumes that memory returned by mmap is
zeroed and it uses it for calloc implementation; if the newly mapped
memory is not zeroed, calloc will return non-zeroed memory.
Fix this bug by testing if the page is equal to ZERO_PAGE(0) and
avoiding the corruption in this case.
If "corrupt_bio_byte" is set to corrupt reads and corrupt_bio_flags is
used, dm-flakey would erroneously return all writes as errors. Likewise,
if "corrupt_bio_byte" is set to corrupt writes, dm-flakey would return
errors for all reads.
Fix the logic so that if fc->corrupt_bio_byte is non-zero, dm-flakey
will not abort reads on writes with an error.
The powerclamp cooling device cur_state shows actual idle observed by
package C-state idle counters. But the implementation is not sufficient
for multi package or multi die system. The cur_state value is incorrect.
On these systems, these counters must be read from each package/die and
somehow aggregate them. But there is no good method for aggregation.
It was not a problem when explicit CPU model addition was required to
enable intel powerclamp. In this way certain CPU models could have
been avoided. But with the removal of CPU model check with the
availability of Package C-state counters, the driver is loaded on most
of the recent systems.
For multi package/die systems, just show the actual target idle state,
the system is trying to achieve. In powerclamp this is the user set
state minus one.
Also there is no use of starting a worker thread for polling package
C-state counters and applying any compensation for multiple package
or multiple die systems.
Fixes: 01a89397f43a ("thermal/powerclamp: remove cpu whitelist") Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Realtek rate control algorithm goes back and forth a lot between
the highest and the lowest rate it's allowed to use. This is due to
a lot of frames being dropped because the retry limits set by
IEEE80211_CONF_CHANGE_RETRY_LIMITS are too low. (Experimentally, they
are 4 for long frames and 7 for short frames.)
The vendor drivers hardcode the value 48 for both retry limits (for
station mode), which makes dropped frames very rare and thus the rate
control is more stable.
Because most Realtek chips handle the rate control in the firmware,
which can't be modified, ignore the limits set by
IEEE80211_CONF_CHANGE_RETRY_LIMITS and use the value 48 (set during
chip initialisation), same as the vendor drivers.
Cc: stable@vger.kernel.org Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/477d745b-6bac-111d-403c-487fc19aa30d@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy ea data from inode entry when expanding ea block if possible.
Then remove the ea entry if expansion success. Thus memcpy to a
temporary buffer may be avoided.
If the expansion fails, we do not need to recovery the removed ea
entry neither in this way.
If snd_ctl_add() fails in aureon_add_controls(), it immediately returns
and leaves ice->gpio_mutex locked. ice->gpio_mutex locks in
snd_ice1712_save_gpio_status and unlocks in
snd_ice1712_restore_gpio_status(ice).
It seems that the mutex is required only for aureon_cs8415_get(),
so snd_ice1712_restore_gpio_status(ice) can be placed
just after that. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The sanity check for an already mapped virq is done outside of the
irq_domain_mutex-protected section which means that an (unlikely) racing
association may not be detected.
Fix this by factoring out the association implementation, which will
also be used in a follow-on change to fix a shared-interrupt mapping
race.
Commit 341c2feee9ad9 ("take calculation of final prot in
security_mmap_file() into a helper") moved the code to update prot, to be
the actual protections applied to the kernel, to a new helper called
mmap_prot().
However, while without the helper ima_file_mmap() was getting the updated
prot, with the helper ima_file_mmap() gets the original prot, which
contains the protections requested by the application.
A possible consequence of this change is that, if an application calls
mmap() with only PROT_READ, and the kernel applies PROT_EXEC in addition,
that application would have access to executable memory without having this
event recorded in the IMA measurement list. This situation would occur for
example if the application, before mmap(), calls the personality() system
call with READ_IMPLIES_EXEC as the first argument.
Align ima_file_mmap() parameters with those of the mmap_file LSM hook, so
that IMA can receive both the requested prot and the final prot. Since the
requested protections are stored in a new variable, and the final
protections are stored in the existing variable, this effectively restores
the original behavior of the MMAP_CHECK hook.
Cc: stable@vger.kernel.org Fixes: 341c2feee9ad ("take calculation of final prot in security_mmap_file() into a helper") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When plain IBRS is enabled (not enhanced IBRS), the logic in
spectre_v2_user_select_mitigation() determines that STIBP is not needed.
The IBRS bit implicitly protects against cross-thread branch target
injection. However, with legacy IBRS, the IBRS bit is cleared on
returning to userspace for performance reasons which leaves userspace
threads vulnerable to cross-thread branch target injection against which
STIBP protects.
Exclude IBRS from the spectre_v2_in_ibrs_mode() check to allow for
enabling STIBP (through seccomp/prctl() by default or always-on, if
selected by spectre_v2_user kernel cmdline parameter).
The AMD side of the loader has always claimed to support mixed
steppings. But somewhere along the way, it broke that by assuming that
the cached patch blob is a single one instead of it being one per
*node*.
So turn it into a per-node one so that each node can stash the blob
relevant for it.
[ NB: Fixes tag is not really the exactly correct one but it is good
enough. ]
Fixes: 10142e5e821f ("x86/microcode: Merge the early microcode loader") Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Cc: <stable@kernel.org> # 2355370cd941 ("x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter") Cc: <stable@kernel.org> # a5ad92134bd1 ("x86/microcode/AMD: Add a @cpu parameter to the reloading functions") Link: https://lore.kernel.org/r/20230130161709.11615-4-bp@alien8.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When arch_prepare_optimized_kprobe calculating jump destination address,
it copies original instructions from jmp-optimized kprobe (see
__recover_optprobed_insn), and calculated based on length of original
instruction.
arch_check_optimized_kprobe does not check KPROBE_FLAG_OPTIMATED when
checking whether jmp-optimized kprobe exists.
As a result, setup_detour_execution may jump to a range that has been
overwritten by jump destination address, resulting in an inval opcode error.
For example, assume that register two kprobes whose addresses are
<func+9> and <func+11> in "func" function.
The original code of "func" function is as follows:
2. Register the kprobe for <func+9>, assume that is kp2, corresponding optimized_kprobe is op2.
register_kprobe(kp2)
register_aggr_kprobe
alloc_aggr_kprobe
__prepare_optimized_kprobe
arch_prepare_optimized_kprobe
__recover_optprobed_insn // copy original bytes from kp1->optinsn.copied_insn,
// jump address = <func+14>
3. disable kp1:
disable_kprobe(kp1)
__disable_kprobe
...
if (p == orig_p || aggr_kprobe_disabled(orig_p)) {
ret = disarm_kprobe(orig_p, true) // add op1 in unoptimizing_list, not unoptimized
orig_p->flags |= KPROBE_FLAG_DISABLED; // op1->flags == KPROBE_FLAG_OPTIMATED | KPROBE_FLAG_DISABLED
...
4. unregister kp2
__unregister_kprobe_top
...
if (!kprobe_disabled(ap) && !kprobes_all_disarmed) {
optimize_kprobe(op)
...
if (arch_check_optimized_kprobe(op) < 0) // because op1 has KPROBE_FLAG_DISABLED, here not return
return;
p->kp.flags |= KPROBE_FLAG_OPTIMIZED; // now op2 has KPROBE_FLAG_OPTIMIZED
}
commit 2d3ebe27fef7 ("kprobes: Set unoptimized flag after unoptimizing code")
modified the update timing of the KPROBE_FLAG_OPTIMIZED, a optimized_kprobe
may be in the optimizing or unoptimizing state when op.kp->flags
has KPROBE_FLAG_OPTIMIZED and op->list is not empty.
The __recover_optprobed_insn check logic is incorrect, a kprobe in the
unoptimizing state may be incorrectly determined as unoptimizing.
As a result, incorrect instructions are copied.
The optprobe_queued_unopt function needs to be exported for invoking in
arch directory.
Link: https://lore.kernel.org/all/20230216034247.32348-2-yangjihong1@huawei.com/ Fixes: 2d3ebe27fef7 ("kprobes: Set unoptimized flag after unoptimizing code") Cc: stable@vger.kernel.org Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable SVM and more importantly force GIF=1 when halting a CPU or
rebooting the machine. Similar to VMX, SVM allows software to block
INITs via CLGI, and thus can be problematic for a crash/reboot. The
window for failure is smaller with SVM as INIT is only blocked while
GIF=0, i.e. between CLGI and STGI, but the window does exist.
Fixes: 2b5df4a9b263 ("x86/reboot: Turn off KVM when halting a CPU") Cc: stable@vger.kernel.org Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20221130233650.1404148-5-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable SVM on all CPUs via NMI shootdown during an emergency reboot.
Like VMX, SVM can block INIT, e.g. if the emergency reboot is triggered
between CLGI and STGI, and thus can prevent bringing up other CPUs via
INIT-SIPI-SIPI.
Disable virtualization in crash_nmi_callback() and rework the
emergency_vmx_disable_all() path to do an NMI shootdown if and only if a
shootdown has not already occurred. NMI crash shootdown fundamentally
can't support multiple invocations as responding CPUs are deliberately
put into halt state without unblocking NMIs. But, the emergency reboot
path doesn't have any work of its own, it simply cares about disabling
virtualization, i.e. so long as a shootdown occurred, emergency reboot
doesn't care who initiated the shootdown, or when.
If "crash_kexec_post_notifiers" is specified on the kernel command line,
panic() will invoke crash_smp_send_stop() and result in a second call to
nmi_shootdown_cpus() during native_machine_emergency_restart().
Invoke the callback _before_ disabling virtualization, as the current
VMCS needs to be cleared before doing VMXOFF. Note, this results in a
subtle change in ordering between disabling virtualization and stopping
Intel PT on the responding CPUs. While VMX and Intel PT do interact,
VMXOFF and writes to MSR_IA32_RTIT_CTL do not induce faults between one
another, which is all that matters when panicking.
Harden nmi_shootdown_cpus() against multiple invocations to try and
capture any such kernel bugs via a WARN instead of hanging the system
during a crash/dump, e.g. prior to the recent hardening of
register_nmi_handler(), re-registering the NMI handler would trigger a
double list_add() and hang the system if CONFIG_BUG_ON_DATA_CORRUPTION=y.
Extract the disabling logic to a common helper to deduplicate code, and
to prepare for doing the shootdown in the emergency reboot path if SVM
is supported.
Note, prior to commit 36c1906aacc7 ("x86/reboot: Force all cpus to exit
VMX root if VMX is supported"), nmi_shootdown_cpus() was subtly protected
against a second invocation by a cpu_vmx_enabled() check as the kdump
handler would disable VMX if it ran first.
Fixes: 36c1906aacc7 ("x86/reboot: Force all cpus to exit VMX root if VMX is supported") Cc: stable@vger.kernel.org Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: https://lore.kernel.org/all/20220427224924.592546-2-gpiccoli@igalia.com Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20221130233650.1404148-2-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set GIF=1 prior to disabling SVM to ensure that INIT is recognized if the
kernel is disabling SVM in an emergency, e.g. if the kernel is about to
jump into a crash kernel or may reboot without doing a full CPU RESET.
If GIF is left cleared, the new kernel (or firmware) will be unabled to
awaken APs. Eat faults on STGI (due to EFER.SVME=0) as it's possible
that SVM could be disabled via NMI shootdown between reading EFER.SVME
and executing STGI.
Migration mode is a VM attribute which enables tracking of changes in
storage attributes (PGSTE). It assumes dirty tracking is enabled on all
memslots to keep a dirty bitmap of pages with changed storage attributes.
When enabling migration mode, we currently check that dirty tracking is
enabled for all memslots. However, userspace can disable dirty tracking
without disabling migration mode.
Since migration mode is pointless with dirty tracking disabled, disable
migration mode whenever userspace disables dirty tracking on any slot.
Also update the documentation to clarify that dirty tracking must be
enabled when enabling migration mode, which is already enforced by the
code in kvm_s390_vm_start_migration().
Also highlight in the documentation for KVM_S390_GET_CMMA_BITS that it
can now fail with -EINVAL when dirty tracking is disabled while
migration mode is on. Move all the error codes to a table so this stays
readable.
To disable migration mode, slots_lock should be held, which is taken
in kvm_set_memory_region() and thus held in
kvm_arch_prepare_memory_region().
Restructure the prepare code a bit so all the sanity checking is done
before disabling migration mode. This ensures migration mode isn't
disabled when some sanity check fails.
Destroy and free the target coalesced MMIO device if unregistering said
device fails. As clearly noted in the code, kvm_io_bus_unregister_dev()
does not destroy the target device.
When we append new block just after the end of preallocated extent, the
code in inode_getblk() wrongly determined we're going to use the
preallocated extent which resulted in adding block into a wrong logical
offset in the file. Sequence like this manifests it:
The code that determined the use of preallocated extent is actually
stale because udf_do_extend_file() does not create preallocation anymore
so after calling that function we are sure there's no usable
preallocation. Just remove the faulty condition.
CC: stable@vger.kernel.org Fixes: 189b02ac597c ("udf: Discard preallocation before extending file with a hole") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When UDF filesystem is corrupted, hidden system inodes can be linked
into directory hierarchy which is an avenue for further serious
corruption of the filesystem and kernel confusion as noticed by syzbot
fuzzed images. Refuse to access system inodes linked into directory
hierarchy and vice versa.
CC: stable@vger.kernel.org Reported-by: syzbot+38695a20b8addcbc1084@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System files in UDF filesystem have link count 0. To not confuse VFS we
fudge the link count to be 1 when reading such inodes however we forget
to restore the link count of 0 when writing such inodes. Fix that.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write to inline file fails (or happens only partly), we still
updated length of inline data as if the whole write succeeded. Fix the
update of length of inline data to happen only if the write succeeds.
Reported-by: syzbot+0937935b993956ba28ab@syzkaller.appspotmail.com CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When merging very long extents we try to push as much length as possible
to the first extent. However this is unnecessarily complicated and not
really worth the trouble. Furthermore there was a bug in the logic
resulting in corrupting extents in the file as syzbot reproducer shows.
So just don't bother with the merging of extents that are too long
together.
CC: stable@vger.kernel.org Reported-by: syzbot+60f291a24acecb3c2bd5@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a file expansion failed because we didn't have enough space for
indirect extents make sure we truncate extents created so far so that we
don't leave extents beyond EOF.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes three issues on move extents ioctl without auto defrag:
a) In ocfs2_find_victim_alloc_group(), we have to convert bits to block
first in case of global bitmap.
b) In ocfs2_probe_alloc_group(), when finding enough bits in block
group bitmap, we have to back off move_len to start pos as well,
otherwise it may corrupt filesystem.
c) In ocfs2_ioctl_move_extents(), set me_threshold both for non-auto
and auto defrag paths. Otherwise it will set move_max_hop to 0 and
finally cause unexpectedly ENOSPC error.
Currently there are no tools triggering the above issues since
defragfs.ocfs2 enables auto defrag by default. Tested with manually
changing defragfs.ocfs2 to run non auto defrag path.
Link: https://lkml.kernel.org/r/20230220050526.22020-1-heming.zhao@suse.com Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug has the same root cause of 'commit 05a5c6839af8 ("ocfs2: call
ocfs2_journal_access_di() before ocfs2_journal_dirty() in
ocfs2_write_end_nolock()")'. For this bug, jbd2_journal_restart() is
called by ocfs2_split_extent() during defragmenting.
How to fix
For ocfs2_split_extent() can handle journal operations totally by itself.
Caller doesn't need to call journal access/dirty pair, and caller only
needs to call journal start/stop pair. The fix method is to remove
journal access/dirty from __ocfs2_move_extent().
The discussion for this patch:
https://oss.oracle.com/pipermail/ocfs2-devel/2023-February/000647.html
Link: https://lkml.kernel.org/r/20230217003717.32469-1-heming.zhao@suse.com Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing a page from an encrypted file that is using
filesystem-layer encryption (not inline encryption), f2fs encrypts the
pagecache page into a bounce page, then writes the bounce page.
It also passes the bounce page to wbc_account_cgroup_owner(). That's
incorrect, because the bounce page is a newly allocated temporary page
that doesn't have the memory cgroup of the original pagecache page.
This makes wbc_account_cgroup_owner() not account the I/O to the owner
of the pagecache page as it should.
Fix this by always passing the pagecache page to
wbc_account_cgroup_owner().
When converting an inline directory to a regular one, f2fs is leaking
uninitialized memory to disk because it doesn't initialize the entire
directory block. Fix this by zero-initializing the block.
This bug was introduced by commit 8c0c37f03ded ("f2fs: avoid unneeded
initializing when converting inline dentry"), which didn't consider the
security implications of leaking uninitialized memory to disk.
This was found by running xfstest generic/435 on a KMSAN-enabled kernel.
Fixes: 8c0c37f03ded ("f2fs: avoid unneeded initializing when converting inline dentry") Cc: <stable@vger.kernel.org> # v4.3+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current hfsplus_put_super first calls hfs_btree_close on
sbi->ext_tree, then invokes iput on sbi->hidden_dir, resulting in an
use-after-free issue in hfsplus_release_folio.
As shown in hfsplus_fill_super, the error handling code also calls iput
before hfs_btree_close.
To fix this error, we move all iput calls before hfsplus_btree_close.
Note that this patch is tested on Syzbot.
Link: https://lkml.kernel.org/r/20230226124948.3175736-1-mudongliangabcd@gmail.com Reported-by: syzbot+57e3e98f7e3b80f64d56@syzkaller.appspotmail.com Tested-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/* Dispose of resources used by a node */
void hfs_bnode_put(struct hfs_bnode *node)
{
if (node) {
<skipped>
BUG_ON(!atomic_read(&node->refcnt)); <- we have issue here!!!!
<skipped>
}
}
By tracing the refcnt, I found the node is created by hfs_bmap_alloc()
with refcnt 1. Then the node is used by hfs_btree_write(). There is a
missing of hfs_bnode_get() after find the node. The issue happened in
following path:
<alloc>
hfs_bmap_alloc
hfs_bnode_find
__hfs_bnode_create <- allocate a new node with refcnt 1.
hfs_bnode_put <- decrease the refcnt
<write>
hfs_btree_write
hfs_bnode_find
__hfs_bnode_create
hfs_bnode_findhash <- find the node without refcnt increased.
hfs_bnode_put <- trigger the BUG_ON() since refcnt is 0.
Link: https://lkml.kernel.org/r/20221212021627.3766829-1-liushixin2@huawei.com Reported-by: syzbot+5b04b49a7ec7226c7426@syzkaller.appspotmail.com Signed-off-by: Liu Shixin <liushixin2@huawei.com> Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent test_kprobe_missed kprobes kunit test uncovers the following
problem. Once kprobe is triggered from another kprobe (kprobe reenter),
all future kprobes on this cpu are considered as kprobe reenter, thus
pre_handler and post_handler are not being called and kprobes are counted
as "missed".
Commit ef41fee3efe0 ("[S390] kprobes: activation and deactivation")
introduced a simpler scheme for kprobes (de)activation and status
tracking by using push_kprobe/pop_kprobe, which supposed to work for
both initial kprobe entry as well as kprobe reentry and helps to avoid
handling those two cases differently. The problem is that a sequence of
calls in case of kprobes reenter:
push_kprobe() <- NULL (current_kprobe)
push_kprobe() <- kprobe1 (current_kprobe)
pop_kprobe() -> kprobe1 (current_kprobe)
pop_kprobe() -> kprobe1 (current_kprobe)
leaves "kprobe1" as "current_kprobe" on this cpu, instead of setting it
to NULL. In fact push_kprobe/pop_kprobe can only store a single state
(there is just one prev_kprobe in kprobe_ctlblk). Which is a hack but
sufficient, there is no need to have another prev_kprobe just to store
NULL. To make a simple and backportable fix simply reset "prev_kprobe"
when kprobe is poped from this "stack". No need to worry about
"kprobe_status" in this case, because its value is only checked when
current_kprobe != NULL.
Recent test_kprobe_missed kprobes kunit test uncovers the following error
(reported when CONFIG_DEBUG_ATOMIC_SLEEP is enabled):
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 662, name: kunit_try_catch
preempt_count: 0, expected: 0
RCU nest depth: 0, expected: 0
no locks held by kunit_try_catch/662.
irq event stamp: 280
hardirqs last enabled at (279): [<00000003e60a3d42>] __do_pgm_check+0x17a/0x1c0
hardirqs last disabled at (280): [<00000003e3bd774a>] kprobe_exceptions_notify+0x27a/0x318
softirqs last enabled at (0): [<00000003e3c5c890>] copy_process+0x14a8/0x4c80
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 46 PID: 662 Comm: kunit_try_catch Tainted: G N 6.2.0-173644-g44c18d77f0c0 #2
Hardware name: IBM 3931 A01 704 (LPAR)
Call Trace:
[<00000003e60a3a00>] dump_stack_lvl+0x120/0x198
[<00000003e3d02e82>] __might_resched+0x60a/0x668
[<00000003e60b9908>] __mutex_lock+0xc0/0x14e0
[<00000003e60bad5a>] mutex_lock_nested+0x32/0x40
[<00000003e3f7b460>] unregister_kprobe+0x30/0xd8
[<00000003e51b2602>] test_kprobe_missed+0xf2/0x268
[<00000003e51b5406>] kunit_try_run_case+0x10e/0x290
[<00000003e51b7dfa>] kunit_generic_run_threadfn_adapter+0x62/0xb8
[<00000003e3ce30f8>] kthread+0x2d0/0x398
[<00000003e3b96afa>] __ret_from_fork+0x8a/0xe8
[<00000003e60ccada>] ret_from_fork+0xa/0x40
The reason for this error report is that kprobes handling code failed
to restore irqs.
The problem is that when kprobe is triggered from another kprobe
post_handler current sequence of enable_singlestep / disable_singlestep
is the following:
enable_singlestep <- original kprobe (saves kprobe_saved_imask)
enable_singlestep <- kprobe triggered from post_handler (clobbers kprobe_saved_imask)
disable_singlestep <- kprobe triggered from post_handler (restores kprobe_saved_imask)
disable_singlestep <- original kprobe (restores wrong clobbered kprobe_saved_imask)
There is just one kprobe_ctlblk per cpu and both calls saves and
loads irq mask to kprobe_saved_imask. To fix the problem simply move
resume_execution (which calls disable_singlestep) before calling
post_handler. This also fixes the problem that post_handler is called
with pt_regs which were not yet adjusted after single-stepping.
When debugging vmlinux with QEMU + GDB, the following GDB error may
occur:
(gdb) c
Continuing.
Warning:
Cannot insert breakpoint -1.
Cannot access memory at address 0xffffffffffff95c0
Command aborted.
(gdb)
The reason is that, when .interp section is present, GDB tries to
locate the file specified in it in memory and put a number of
breakpoints there (see enable_break() function in gdb/solib-svr4.c).
Sometimes GDB finds a bogus location that matches its heuristics,
fails to set a breakpoint and stops. This makes further debugging
impossible.
The .interp section contains misleading information anyway (vmlinux
does not need ld.so), so fix by discarding it.
Make sure to disable the alarm before updating the four alarm time
registers to avoid spurious alarms during the update.
Note that the disable needs to be done outside of the ctrl_reg_lock
section to prevent a racing alarm interrupt from disabling the newly set
alarm when the lock is released.
Fixes: 8b34661e0495 ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC") Cc: stable@vger.kernel.org # 3.1 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: David Collins <quic_collinsd@quicinc.com> Link: https://lore.kernel.org/r/20230202155448.6715-2-johan+linaro@kernel.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coreboot framebuffer doesn't support transparency, its 'reserved'
bit field is merely padding for byte/word alignment of pixel colors [1].
When trying to match the framebuffer to a simplefb format, the kernel
driver unnecessarily requires the format's transparency bit field to
exactly match this padding, even if the former is zero-width.
Due to a coreboot bug [2] (fixed upstream), some boards misreport the
reserved field's size as equal to its position (0x18 for both on a
'Lick' Chromebook), and the driver fails to probe where it would have
otherwise worked fine with e.g. the a8r8g8b8 or x8r8g8b8 formats.
Remove the transparency comparison with reserved bits. When the
bits-per-pixel and other color components match, transparency will
already be in a subset of the reserved field. Not forcing it to match
reserved bits allows the driver to work on the boards which misreport
the reserved field. It also enables using simplefb formats that don't
have transparency bits, although this doesn't currently happen due to
format support and ordering in linux/platform_data/simplefb.h.
At first, I thought this might be a source of nfsd_file overputs, but
the current callers seem to avoid an extra put when nfsd4_verify_copy
returns an error.
Still, it's "bad form" to leave the pointers filled out when we don't
have a reference to them anymore, and that might lead to bugs later.
Zero them out as a defensive coding measure.
Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use devm_kasprintf() instead of kasprintf() to avoid any potential
leaks. At the moment drivers have no remove functionality thus
there is no need for fixes tag.
Coretemp's platform driver is unconventional. All the real work is done
globally by the initcall and CPU hotplug notifiers, while the "driver"
effectively just wraps an allocation and the registration of the hwmon
interface in a long-winded round-trip through the driver core. The whole
logic of dynamically creating and destroying platform devices to bring
the interfaces up and down is error prone, since it assumes
platform_device_add() will synchronously bind the driver and set drvdata
before it returns, thus results in a NULL dereference if drivers_autoprobe
is turned off for the platform bus. Furthermore, the unusual approach of
doing that from within a CPU hotplug notifier, already commented in the
code that it deadlocks suspend, also causes lockdep issues for other
drivers or subsystems which may want to legitimately register a CPU
hotplug notifier from a platform bus notifier.
All of these issues can be solved by ripping this unusual behaviour out
completely, simply tying the platform devices to the lifetime of the
module itself, and directly managing the hwmon interfaces from the
hotplug notifiers. There is a slight user-visible change in that
/sys/bus/platform/drivers/coretemp will no longer appear, and
/sys/devices/platform/coretemp.n will remain present if package n is
hotplugged off, but hwmon users should really only be looking for the
presence of the hwmon interfaces, whose behaviour remains unchanged.
The compiler has no way to know if "id" is within the array bounds of
the regulators array. Add a check for this and a build-time check that
the regulators and reg_voltage_map arrays are sized the same. Seen with
GCC 13:
../drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
../drivers/regulator/s5m8767.c:936:35: warning: array subscript [0, 36] is outside array bounds of 'struct regulator_desc[37]' [-Warray-bounds=]
936 | regulators[id].vsel_reg =
| ~~~~~~~~~~^~~~
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: linux-samsung-soc@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230128005358.never.313-kees@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
../sound/soc/kirkwood/kirkwood-dma.c: In function
'kirkwood_dma_conf_mbus_windows.constprop':
../sound/soc/kirkwood/kirkwood-dma.c:90:24: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
90 | if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
| ~~^~~~~~
Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230127224128.never.410-kees@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
iio was allocated in atom_index_iio() called by atom_parse(),
but it doesn't got released when the dirver is shutdown.
Fix this kmemleak by free it in radeon_atombios_fini().
Signed-off-by: Liwei Song <liwei.song@windriver.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Fixing smatch error:
dm_resume() error: we previously assumed 'aconnector->dc_link' could be null
[How]
Check if dc_link null at the beginning of the loop,
so further checks can be dropped.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While there is logic about the difference between ksize and usize,
copy_struct_from_user() didn't check the size of the destination buffer
(when it was known) against ksize. Add this check so there is an upper
bounds check on the possible memset() call, otherwise lower bounds
checks made by callers will trigger bounds warnings under -Warray-bounds.
Seen under GCC 13:
In function 'copy_struct_from_user',
inlined from 'iommufd_fops_ioctl' at
../drivers/iommu/iommufd/main.c:333:8:
../include/linux/fortify-string.h:59:33: warning: '__builtin_memset' offset [57, 4294967294] is out of the bounds [0, 56] of object 'buf' with type 'union ucmd_buffer' [-Warray-bounds=]
59 | #define __underlying_memset __builtin_memset
| ^
../include/linux/fortify-string.h:453:9: note: in expansion of macro '__underlying_memset'
453 | __underlying_memset(p, c, __fortify_size); \
| ^~~~~~~~~~~~~~~~~~~
../include/linux/fortify-string.h:461:25: note: in expansion of macro '__fortify_memset_chk'
461 | #define memset(p, c, s) __fortify_memset_chk(p, c, s, \
| ^~~~~~~~~~~~~~~~~~~~
../include/linux/uaccess.h:334:17: note: in expansion of macro 'memset'
334 | memset(dst + size, 0, rest);
| ^~~~~~
../drivers/iommu/iommufd/main.c: In function 'iommufd_fops_ioctl':
../drivers/iommu/iommufd/main.c:311:27: note: 'buf' declared here
311 | union ucmd_buffer buf;
| ^~~
GCC does not like having a partially allocated object, since it cannot
reason about it for bounds checking when it is passed to other code.
Instead, fully allocate sig_inputArgs. (Alternatively, sig_inputArgs
should be defined as a struct coda_in_hdr, if it is actually not using
any other part of the union.) Seen under GCC 13:
../fs/coda/upcall.c: In function 'coda_upcall':
../fs/coda/upcall.c:801:22: warning: array subscript 'union inputArgs[0]' is partly outside array bounds of 'unsigned char[20]' [-Warray-bounds=]
801 | sig_inputArgs->ih.opcode = CODA_SIGNAL;
| ^~
Multiple Ideapad Z570 variants need acpi_backlight=native to force native
use on these pre Windows 8 machines since acpi_video backlight control
does not work here.
The original DMI quirk matches on a product_name of "102434U" but other
variants may have different product_name-s such as e.g. "1024D9U".
Move to checking product_version instead as is more or less standard for
Lenovo DMI quirks for similar reasons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionnaly we may get oversized packets from the hardware which
exceed the nomimal 2KiB buffer size we allocate SKBs with. Add an early
check which drops the packet to avoid invoking skb_over_panic() and move
on to processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This prevents CONFIG_FUNCTION_ALIGNMENT and
CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B from having their expected effect
on the ACPICA code. This is doubly unfortunate as in subsequent patches
arm64 will depend upon CONFIG_FUNCTION_ALIGNMENT for its ftrace
implementation.
Drop the '-Os' flag when building the ACPICA code. With this removed,
the code builds cleanly and works correctly in testing so far.
I've tested this by selecting CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B=y,
building and booting a kernel using ACPI, and looking for misaligned
text symbols:
With the patch applied, the remaining unaligned text labels are a
combination of static call trampolines and labels in assembly, which can
be dealt with in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Florent Revest <revest@chromium.org> Cc: Len Brown <lenb@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Moore <robert.moore@intel.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Will Deacon <will@kernel.org> Cc: linux-acpi@vger.kernel.org Link: https://lore.kernel.org/r/20230123134603.1064407-4-mark.rutland@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There were a few places we had missed checking the VSI type to make sure
it was definitely a PF VSI, before calling setup functions intended only
for the PF VSI.
This doesn't fix any explicit bugs but cleans up the code in a few
places and removes one explicit != vsi->type check that can be
superseded by this code (it's a super set)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
__inet_hash_connect() has a fast path taken if sk_head(&tb->owners) is
equal to the sk parameter.
sk_head() returns the hlist_entry() with respect to the sk_node field.
However entries in the tb->owners list are inserted with respect to the
sk_bind_node field with sk_add_bind_node().
Thus the check would never pass and the fast path never execute.
This fast path has never been executed or tested as this bug seems
to be present since commit 1da177e4c3f4 ("Linux-2.6.12-rc2"), thus
remove it to reduce code complexity.
Fix an integer underflow that leads to a null pointer dereference in
'mt7601u_rx_skb_from_seg()'. The variable 'dma_len' in the URB packet
could be manipulated, which could trigger an integer underflow of
'seg_len' in 'mt7601u_rx_process_seg()'. This underflow subsequently
causes the 'bad_frame' checks in 'mt7601u_rx_skb_from_seg()' to be
bypassed, eventually leading to a dereference of the pointer 'p', which
is a null pointer.
Ensure that 'dma_len' is greater than 'min_seg_len'.
Fix a stack-out-of-bounds read in brcmfmac that occurs
when 'buf' that is not null-terminated is passed as an argument of
strreplace() in brcmf_c_preinit_dcmds(). This buffer is filled with
a CLM version string by memcpy() in brcmf_fil_iovar_data_get().
Ensure buf is null-terminated.
Currently, x86_spec_ctrl_base is read at boot time and speculative bits
are set if Kconfig items are enabled. For example, IBRS is enabled if
CONFIG_CPU_IBRS_ENTRY is configured, etc. These MSR bits are not cleared
if the mitigations are disabled.
This is a problem when kexec-ing a kernel that has the mitigation
disabled from a kernel that has the mitigation enabled. In this case,
the MSR bits are not cleared during the new kernel boot. As a result,
this might have some performance degradation that is hard to pinpoint.
This problem does not happen if the machine is (hard) rebooted because
the bit will be cleared by default.
The nanosleep syscalls use the restart_block mechanism, with a quirk:
The `type` and `rmtp`/`compat_rmtp` fields are set up unconditionally on
syscall entry, while the rest of the restart_block is only set up in the
unlikely case that the syscall is actually interrupted by a signal (or
pseudo-signal) that doesn't have a signal handler.
If the restart_block was set up by a previous syscall (futex(...,
FUTEX_WAIT, ...) or poll()) and hasn't been invalidated somehow since then,
this will clobber some of the union fields used by futex_wait_restart() and
do_restart_poll().
If userspace afterwards wrongly calls the restart_syscall syscall,
futex_wait_restart()/do_restart_poll() will read struct fields that have
been clobbered.
This doesn't actually lead to anything particularly interesting because
none of the union fields contain trusted kernel data, and
futex(..., FUTEX_WAIT, ...) and poll() aren't syscalls where it makes much
sense to apply seccomp filters to their arguments.
So the current consequences are just of the "if userspace does bad stuff,
it can damage itself, and that's not a problem" flavor.
But still, it seems like a hazard for future developers, so invalidate the
restart_block when partly setting it up in the nanosleep syscalls.
The return value from the call to intel_tcc_get_tjmax() is int, which can
be a negative error code. However, the return value is being assigned to
an u32 variable 'tj_max', so making 'tj_max' an int.
Eliminate the following warning:
./drivers/thermal/intel/intel_soc_dts_iosf.c:394:5-11: WARNING: Unsigned expression compared with zero: tj_max < 0
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3637 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The normal grace period's RCU CPU stall warnings are invoked from the
scheduling-clock interrupt handler, and can thus invoke smp_processor_id()
with impunity, which allows them to directly invoke dump_cpu_task().
In contrast, the expedited grace period's RCU CPU stall warnings are
invoked from process context, which causes the dump_cpu_task() function's
calls to smp_processor_id() to complain bitterly in debug kernels.
This commit therefore causes synchronize_rcu_expedited_wait() to disable
preemption around its call to dump_cpu_task().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log