Imre Deak [Thu, 16 Jun 2016 13:37:20 +0000 (16:37 +0300)]
drm/i915/bxt: Fix PPS lost state after suspend breaking eDP link training
The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.
This also paves the way towards using the actual port->PPS instance
mapping based on VBT.
This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.
Imre Deak [Tue, 21 Jun 2016 08:51:49 +0000 (11:51 +0300)]
drm/i915: Group all the PPS init steps to one place
Move the early PPS initialization calls next to the rest of PPS
initialization steps. This allows us to forgo a duplicated call to
intel_dp_init_panel_power_sequencer_registers() on VLV/CHV.
This will swap the order of DP AUX registration wrt. PPS initialization.
There is an existing race here in case of a user space access via the
DPAUX device node after DP AUX registration and before calling
intel_dp_init_panel_power_sequencer_registers(), but this change won't
make this worse. The fix for this is to separate DP AUX initialization
and registration, that's a separate work already underway.
The order of MST wrt. PPS init as well as the order of
intel_dp_init_panel_power_sequencer_registers() wrt.
intel_edp_panel_vdd_sanitize() also swap, which is ok, there are no
dependencies between these steps.
Imre Deak [Tue, 21 Jun 2016 08:51:48 +0000 (11:51 +0300)]
drm/i915: Initialize the PPS HW before its first use
The initial DPCD read for eDP detection involves using the PPS, but so
far we only initialized the PPS registers after the DPCD read. The
reason this was done so far is to preserve a possible LVDS PPS HW setup
if LVDS is detected but eDP is not. This is not an issue any more after
the previous patch, so we can move the init earlier now.
This was caught by CI with the PPS sanity checks in place and the
initial eDP DPCD readout waiting for the panel power cycle timeout
without the PPS registers being initialized.
Imre Deak [Tue, 21 Jun 2016 08:51:47 +0000 (11:51 +0300)]
drm/i915/ibx, cpt: Don't attempt to register eDP if LVDS was detected
Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.
We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.
v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
(Ville)
Tvrtko Ursulin [Tue, 21 Jun 2016 14:07:14 +0000 (15:07 +0100)]
drm/i915/guc: Remove one unnecessary variable
No need for local struct drm_device * since dev_priv is the
correct thing to pass in to NEEDS_WaRsDisableCoarsePowerGating
anyway. Changed the macro definition for the latter to reflect
that as well.
drm/i915: Use connector_type for printing in intel_connector_info, v2.
Instead of looking at encoder->type, which may be set to UNKNOWN,
use connector->connector_type. Info cannot be printed for MST
connectors which may have a NULL encoder, return early in that case.
Changes since v1:
- Whitelist encoder types for HDMI and LVDS.
- Fix oops on MST.
- Do not list encoder types for eDP/DP, they're always valid.
Michał Winiarski [Mon, 20 Jun 2016 09:58:27 +0000 (11:58 +0200)]
drm/i915: Set softmin frequency on idle->busy transition
If the GPU load is low enough, it's possible that we'll be stuck at idle
frequency rather than transition into softmin frequency requested by
userspace.
v2: Use intel_set_rps, drop vlv_set_idle
v3: Back to vlv_set_idle, clamp to valid range
v4: Place intel_set_rps at the end
References: https://bugs.freedesktop.org/show_bug.cgi?id=89728 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Imre Deak <imre.deak@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1466416707-12075-1-git-send-email-michal.winiarski@intel.com
Dave Gordon [Mon, 20 Jun 2016 14:18:07 +0000 (15:18 +0100)]
drm/i915/guc: index host arrays by i915 engine ID, not guc_id
The ONLY places that guc_id (aka hw_id) should be used are those where
the value or address is determined by and shared with the GuC firmware;
specifically, when filling in the GuC-context-descriptor or the GuC
addon data, or putting an entry in the GuC's work queue.
It need not (and therefore should not) be used to index GuC statistics
or similar host-managed tracking data. In particular, i915_guc_submit()
produces (and debugfs decodes) GuC submission statistics which should be
indexed by driver-engine-id rather then guc-engine-id.
Chris Wilson [Tue, 21 Jun 2016 08:16:55 +0000 (09:16 +0100)]
drm/i915/fbdev: Flush mode configuration before lastclose
During lastclose, we call intel_fbdev_restore_mode() to switch back to
the fbcon configuration on return to VT. However, if we have not yet
finished the asynchronous fbdev initialisation, the current mode will be
invalid and trigger WARNs upon application.
Serialise with the outstanding initialisation if the first application
exits quickly. Note that to hit this in practice requires using an
unregistered async_domain as otherwise modprobe will force a full
synchronisation prior to init() completing.
v2: Reuse comment explaining the +1 by refactoring the wait on fbdev
sync in the previous patch.
Reported-by: Gustav Fägerlind <gustav.fagerlind@gmail.com> Reported-by: "Li, Weinan Z" <weinan.z.li@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93580 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-3-git-send-email-chris@chris-wilson.co.uk
Chris Wilson [Tue, 21 Jun 2016 08:16:54 +0000 (09:16 +0100)]
drm/i915/fbdev: Limit the global async-domain synchronization
During cleanup we have to synchronise with the async task we are using
to initialise and register our fbdev. Currently, we are using a full
synchronisation on the global domain, but we can restrict this to just
synchronising up to our task if we remember our cookie.
Whilst there, streamline the function parameters.
v2: async_synchronize_cookie() takes an exclusive upper bound, to
synchronize with our task we have to pass in the next cookie.
v3: Drop premature disregarding of the active cookie (we need to wait
until the task is complete before continuing in the teardown).
v4: Refactor waiting on async to incorporate a comment explaining why we
need the +1.
Chris Wilson [Tue, 21 Jun 2016 08:16:53 +0000 (09:16 +0100)]
drm/i915/fbdev: Perform async fbdev initialisation much later
Setting up fbdev requires everything ready and registered (in particular
the connectors). In the forthcoming patches, we defer registration of the KMS
objects and unless we defer setting off fbdev, it may run before they are
registered and oops.
Chris Wilson [Fri, 17 Jun 2016 17:46:39 +0000 (14:46 -0300)]
drm/i915: use ORIGIN_CPU for frontbuffer invalidation on WC mmaps
... instead of the previous ORIGIN_GTT. This should actually
invalidate FBC once something is written on the frontbuffer using WC
mmaps. The problem with ORIGIN_GTT is that the automatic hardware
tracking is not able to detect the WC writes as it can detect the GTT
writes.
This should help fix the SKL bug where nothing happens when you type
your username/password on lightdm.
This patch was originally pasted on an email by Chris and converted to
an actual git patch by Paulo.
v2 (from Paulo):
- Make it a full variable instead of a bit-field (Daniel)
- Use WRITE_ONCE (Chris)
v3 (from Paulo):
- Remove huge comment since now we have WRITE_ONCE (Chris)
- Remove uneeded new line (Chris)
- Add Chris' Signed-off-by, authorized via IRC
Paulo Zanoni [Wed, 13 Apr 2016 19:01:09 +0000 (16:01 -0300)]
drm/i915/fbc: sanitize i915.enable_fbc during FBC init
The DDX driver changes its behavior depending on the value it reads
from i915.enable_fbc, so sanitize the value in order to allow it to
know what's going on. It uses this in order to choose the defaults for
the TearFree option. Before this patch, it would read -1 and always
assume that FBC was disabled, so it wouldn't force TearFree.
Paulo Zanoni [Mon, 4 Apr 2016 21:17:15 +0000 (18:17 -0300)]
drm/i915/fbc: update busy_bits even for GTT and flip flushes
We ignore ORIGIN_GTT because the hardware tracking can recognize GTT
writes and take care of them. We also ignore ORIGIN_FLIP because we
deal with flips without relying on the frontbuffer tracking
infrastructure. On the other hand, a flush is a flush and means we're
good to go, so we need to update busy_bits in order to reflect that,
even if we're not going to do anything else about it.
How to reproduce the bug fixed by this patch:
- boot SKL up to the desktop environment
- stop the display manager
- run any of the igt/kms_frontbuffer_tracking/*fbc*onoff* subtests
- the tests will fail
The steps above will create the right conditions for us to lose track
of busy_bits. If you, for example, run the full set of FBC tests, the
onoff subtests will succeed.
Also notice that the "bug" is that we'll just keep FBC disabled on
cases where it could be enabled, so it's not something the users can
perceive, it just affects power consumption numbers on properly
configured machines.
This was kind of a difficult bug to track down. If you're using a
Haswell system running GNOME and you have fbc completely enabled and
working, playing videos can result in video artifacts. Steps to
reproduce:
- Run GNOME
- Ensure FBC is enabled and active
- Download a movie, I used the ogg version of Big Buck Bunny for this
- Run `gst-launch-1.0 filesrc location='some_movie.ogg' ! decodebin !
glimagesink` in a terminal
- Watch for about over a minute, you'll see small horizontal lines go
down the screen.
For the time being, disable FBC for Haswell by default.
Stefan Richter reported kernel freezes (no video artifacts) when fbc
is on. (E3-1245 v3 with HD P4600; openbox and some KDE and LXDE
applications, thread begins at https://lkml.org/lkml/2016/4/26/813).
We also got reports from Steven Honeyman on openbox+roxterm.
v2 (From Paulo):
- Add extra information to the commit message
- Add Fixes tag
- Rebase
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96461
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96464 Fixes: a98ee79317b4 ("drm/i915/fbc: enable FBC by default on HSW and BDW") Cc: stable@vger.kernel.org Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1465487895-7401-1-git-send-email-cpaul@redhat.com
Chris Wilson [Mon, 20 Jun 2016 14:05:52 +0000 (15:05 +0100)]
drm/i915: pwrite/pread do not require obj->base.filp, just pages
The idea behind relaxing the restriction for pread/pwrite was to handle
!obj->base.flip, i.e. non-shmemfs backed objects, which only requires
that the object provide struct pages.
v2: Remove excess (). Note enough editing after copy'n'paste.
v3: Use new i915_gem_object_has_struct_page()
Chris Wilson [Mon, 20 Jun 2016 14:05:51 +0000 (15:05 +0100)]
drm/i915: Extract checking for backing struct pages to a helper
Currently to see if an object is backed by struct pages (as opposed to
being a simple pointer to stolen memory, for example) we do a manual
check on the obj->ops->flags. This is quite shouty and before adding
more checks in future, we should make it a bit calmer.
Mika Kahola [Mon, 20 Jun 2016 08:10:26 +0000 (11:10 +0300)]
drm/i915: Revert DisplayPort fast link training feature
It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.
This is a manual revert of commits 5fa836a9d859 ("drm/i915: DP link
training optimization") and 4e96c97742f4 ("drm/i915: eDP link training
optimization").
Fixes: 5fa836a9d859 ("drm/i915: DP link training optimization") Fixes: 4e96c97742f4 ("drm/i915: eDP link training optimization") Cc: <stable@vger.kernel.org> # v4.2+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393 Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
Zhi Wang [Thu, 16 Jun 2016 12:07:05 +0000 (08:07 -0400)]
drm/i915: Introduce GVT context creation API
GVT workload scheduler needs special host LRC contexts, the so called
"shadow LRC context" to submit guest workload to host i915. During the
guest workload submission, workload scheduler fills the shadow LRC
context with the content of guest LRC context: engine context is copied
without changes, ring context is mostly owned by host i915.
v8:
- Remove the graph temporarily. (Chris)
- Use interruptible mutex_lock. (Chris)
- Rename the function name of creating a GVT context. (Chris)
- Add the missing declaration in i915_drv.h (Chris)
v7:
- Move chart to a better place. (Joonas)
v6:
- Make GVT code as dead code when !CONFIG_DRM_I915_GVT. (Chris)
v5:
- Only compile this feature when CONFIG_DRM_I915_GVT is enabled. (Tvrtko)
- Rebase the code into new repo.
- Add a comment about the ring buffer size. (Joonas)
v2:
Mostly based on Daniel's idea. Call the refactored core logic of GEM
context creation service and LRC context creation service to create the GVT
context.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-10-git-send-email-zhi.a.wang@intel.com
Zhi Wang [Thu, 16 Jun 2016 12:07:04 +0000 (08:07 -0400)]
drm/i915: Support LRC context single submission
This patch introduces the support of LRC context single submission.
As GVT context may come from different guests, which require different
configuration of render registers. It can't be combined into a dual ELSP
submission combo.
Only GVT-g will create this kinds of GEM context currently.
v8:
- Rename the data member in struct i915_gem_context. (Chris)
v7:
- Fix typos in commit message. (Joonas)
v6:
- Make GVT code as dead code when !CONFIG_DRM_I915_GVT. (Chris)
v5:
- Only compile this feature when CONFIG_DRM_I915_GVT=y. (Tvrtko)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-9-git-send-email-zhi.a.wang@intel.com
Zhi Wang [Thu, 16 Jun 2016 12:07:03 +0000 (08:07 -0400)]
drm/i915: Introduce execlist context status change notification
This patch introduces an approach to track the execlist context status
change.
GVT-g uses GVT context as the "shadow context". The content inside GVT
context will be copied back to guest after the context is idle. And GVT-g
has to know the status of the execlist context.
This function is configurable when creating a new GEM context. Currently,
Only GVT-g will create the "status-change-notification" enabled GEM
context.
v10:
- Fix the identation. (Joonas)
v8:
- Remove the boolean flag in struct i915_gem_context. (Joonas)
v7:
- Remove per-engine ctx status notifiers. Use one status notifier for all
engines. (Joonas)
- Add prefix "INTEL_" for related definitions. (Joonas)
- Refine the comments in execlists_context_status_change(). (Joonas)
v6:
- When !CONFIG_DRM_I915_GVT, make GVT code as dead code then compiler
could automatically eliminate them for us. (Chris)
- Always initialize the notifier header, so it could be switched on/off
at runtime. (Chris)
v5:
- Only compile this feature when CONFIG_DRM_I915_GVT is enabled.(Tvrtko)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v8) Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-8-git-send-email-zhi.a.wang@intel.com Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Zhi Wang [Thu, 16 Jun 2016 12:07:02 +0000 (08:07 -0400)]
drm/i915: Make addressing mode bits in context descriptor configurable
Currently the addressing mode bit in context descriptor is statically
generated from the configuration of system-wide PPGTT usage model.
GVT-g will load the PPGTT shadow page table by itself and probably one
guest is using a different addressing mode with i915 host. The addressing
mode bits of a LRC context should be configurable under this case.
v10:
- Fix the identation. (Joonas)
v9:
- Rename the data member in struct i915_gem_context. (Chris)
v8:
- Rename the data member in struct i915_gem_context. (Chris)
v7:
- Move context addressing mode bit into i915_reg.h. (Joonas/Chris)
- Add prefix "INTEL_" for related definitions. (Joonas)
v6:
- Directly save the addressing mode bits inside i915_gem_context. (Chris)
- Move the LRC context addressing mode bits into intel_lrc.h. (Chris)
v5:
- Change USES_FULL_48BIT(dev) to USES_FULL_48BIT(dev_priv) (Tvrtko)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v9) Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-7-git-send-email-zhi.a.wang@intel.com
Zhi Wang [Thu, 16 Jun 2016 12:07:00 +0000 (08:07 -0400)]
drm/i915: gvt: Introduce the basic architecture of GVT-g
This patch introduces the very basic framework of GVT-g device model,
includes basic prototypes, definitions, initialization.
v12:
- Call intel_gvt_init() in driver early initialization stage. (Chris)
v8:
- Remove the GVT idr and mutex in intel_gvt_host. (Joonas)
v7:
- Refine the URL link in Kconfig. (Joonas)
- Refine the introduction of GVT-g host support in Kconfig. (Joonas)
- Remove the macro GVT_ALIGN(), use round_down() instead. (Joonas)
- Make "struct intel_gvt" a data member in struct drm_i915_private.(Joonas)
- Remove {alloc, free}_gvt_device()
- Rename intel_gvt_{create, destroy}_gvt_device()
- Expost intel_gvt_init_host()
- Remove the dummy "struct intel_gvt" declaration in intel_gvt.h (Joonas)
v6:
- Refine introduction in Kconfig. (Chris)
- The exposed API functions will take struct intel_gvt * instead of
void *. (Chris/Tvrtko)
- Remove most memebers of strct intel_gvt_device_info. Will add them
in the device model patches.(Chris)
- Remove gvt_info() and gvt_err() in debug.h. (Chris)
- Move GVT kernel parameter into i915_params. (Chris)
- Remove include/drm/i915_gvt.h, as GVT-g will be built within i915.
- Remove the redundant struct i915_gvt *, as the functions in i915
will directly take struct intel_gvt *.
- Add more comments for reviewer.
v5:
Take Tvrtko's comments:
- Fix the misspelled words in Kconfig
- Let functions take drm_i915_private * instead of struct drm_device *
- Remove redundant prints/local varible initialization
v3:
Take Joonas' comments:
- Change file name i915_gvt.* to intel_gvt.*
- Move GVT kernel parameter into intel_gvt.c
- Remove redundant debug macros
- Change error handling style
- Add introductions for some stub functions
- Introduce drm/i915_gvt.h.
Take Kevin's comments:
- Move GVT-g host/guest check into intel_vgt_balloon in i915_gem_gtt.c
v2:
- Introduce i915_gvt.c.
It's necessary to introduce the stubs between i915 driver and GVT-g host,
as GVT-g components is configurable in kernel config. When disabled, the
stubs here do nothing.
Take Joonas' comments:
- Replace boolean return value with int.
- Replace customized info/warn/debug macros with DRM macros.
- Document all non-static functions like i915.
- Remove empty and unused functions.
- Replace magic number with marcos.
- Set GVT-g in kernel config to "n" by default.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1466078825-6662-5-git-send-email-zhi.a.wang@intel.com Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson [Fri, 17 Jun 2016 07:28:47 +0000 (08:28 +0100)]
drm/i915: Serialise presentation with imported dmabufs
obj->base.dma_buf represents a dma-buf exported from this object (for
use by others). On the contrary, obj->base.import_attach represents the
source dma-buf that was used to create this object (if any). When
serialising with third parties, we need to wait on their rendering via
the import attachment as well as their rendering on our exported
dma-buf.
Daniel Vetter [Mon, 13 Jun 2016 14:13:49 +0000 (16:13 +0200)]
drm/i915: Use atomic commits for legacy page_flips
Note that I didn't start garbage collecting all the legacy flip code
yet, to make it easier to revert this. But there will be _lots_ of
code that can be removed once this is tested on all platforms.
Daniel Vetter [Mon, 13 Jun 2016 14:13:48 +0000 (16:13 +0200)]
drm/i915: Move fb_bits updating later in atomic_commit
Currently it's part of prepare_fb, still in the first phase of
atomic_commit which might fail. Which means that we need to have some
heuristics in cleanup_fb to figure out whether things failed, or
whether we just clean up the old fbs.
That's fragile, and worse, once we start pipelining commits gets
confused: While the last commit is still getting cleanup up we already
hammer in the new one, and fb_bits aren't refcounted, resulting in
lost bits and WARN_ON galore. We could instead try to make cleanup_fb
more clever, but a simpler fix is to postpone the fb_bits tracking
past the point of no return, where we commit all the software state.
That also makes conceptually more sense, since fb_bits must be updated
synchronously from the ioctl (they track usage from userspace pov, not
from the hw pov), right before we're fully committed to the updated.
This fixes WARNING splats from track_fb with page_flip implemented
through atomic_commit.
Reapply "drm/i915: Pass atomic states to fbc update, functions."
The patch was reverted as part of the original nonblocking commit
support, but is required for any kind of nonblocking commit.
This is required to let fbc updates run async. It has a lot of
checks whether certain locks are taken, which can be removed when
the relevant states are passed in as pointers.
Dave Airlie [Wed, 15 Jun 2016 19:49:32 +0000 (05:49 +1000)]
Merge tag 'topic/drm-misc-2016-06-15' of git://anongit.freedesktop.org/drm-intel into drm-next
- best_encoder cleanup from Boris.
- drm_simple_display_pipe helpers from Noralf. Looks really neat imo, and
there's 2-3 in-flight drivers which look like they could/should use it.
Anyway, with this we have now helpers and everything in place to write
drivers for simple hw with fewer complexity in the driver than what
fbdev would need. That was the last complaint I've heard from embedded
folks after we made atomic happen. Mission accomplished!
- nonblocking commit helpers for atomic, plus a bunch of driver patches
for that.
- Prep patch from Laurent for cleaned up pixel format functions.
- More of Gustavo's cleanup for drm vblank functions.
- and a few oddball things in between
Plus the merge of docs-next to prep the docbook->sphinx conversion as
discussed. Jon cc'ed as fyi.
* tag 'topic/drm-misc-2016-06-15' of git://anongit.freedesktop.org/drm-intel: (108 commits)
drm/atomic-helpers: Clear up cleanup_done a bit
drm/atomic-helpers: Stall on the right commit
drm/vmwgfx: use *_32_bits() macros
drm/virtio: Don't reinvent a flipping wheel
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/gma500: use drm_crtc_vblank_{on,off}()
drm/radeon: use crtc directly in drm_crtc_vblank_put()
drm/amdgpu: use crtc directly in drm_crtc_vblank_put()
drm/radeon: use drm_crtc_vblank_{on,off}()
drm/amdgpu: use drm_crtc_vblank_{on,off}()
drm: make drm_vblank_{get,put}() static
drm: remove legacy drm_arm_vblank_event()
drm: remove legacy drm_send_vblank_event()
drm/nouveau: replace legacy vblank helpers
drm/prime: fix error path deadlock fail
drm/dsi: Add uevent callback
drm: fb: cma: fix memory leak
drm: i915: Rely on the default ->best_encoder() behavior where appropriate
drm: Add helper for simple display pipeline
drm/bridge: dw-hdmi: Use drm_atomic_helper_best_encoder()
...
Daniel Vetter [Tue, 14 Jun 2016 17:50:58 +0000 (19:50 +0200)]
drm/atomic-helpers: Stall on the right commit
stall_checks carefully picked out the right commit to stall on, then
promptly used the wrong variable. Due to the break in the next loop
iteration this could be the 3rd commit, or if the list only has 2
entries commit would now point into the struct drm_crtc itself, at
some offset. Hilarity eventually ensues.
For added safety, also break right away instead of iterating once
more, but the real fix is waiting on stall_commit instead of commit.
Paul Bolle [Thu, 3 Mar 2016 10:26:10 +0000 (11:26 +0100)]
drm/vmwgfx: use *_32_bits() macros
Use the upper_32_bits() macro instead of the four line equivalent that
triggers a GCC warning on 32 bits x86:
drivers/gpu/drm/vmwgfx/vmwgfx_cmdbuf.c: In function 'vmw_cmdbuf_header_submit':
drivers/gpu/drm/vmwgfx/vmwgfx_cmdbuf.c:297:25: warning: right shift count >= width of type [-Wshift-count-overflow]
val = (header->handle >> 32);
^
And use the lower_32_bits() macro instead of and-ing with a 32 bits
mask.
Lyude [Tue, 14 Jun 2016 15:04:09 +0000 (11:04 -0400)]
drm/i915/ilk: Don't disable SSC source if it's in use
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v4:
- Fix calculation of final for systems with LVDS panels (fixes BUG() on
CI test suite)
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Daniel Vetter [Thu, 9 Jun 2016 22:07:53 +0000 (00:07 +0200)]
drm/virtio: Don't reinvent a flipping wheel
Now that the core helpers support nonblocking atomic commits there's
no need to invent that wheel separately (instead of fixing the bug in
the atomic implementation of virtio, as it should have been done!).
Dave Gordon [Mon, 13 Jun 2016 16:57:34 +0000 (17:57 +0100)]
drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission
During a hibernate/resume cycle, the whole system is reset, including
the GuC and the doorbell hardware. Then the system is booted up, drivers
are loaded, etc -- the GuC firmware may be loaded and set running at
this point. But then, the booted kernel is replaced by the hibernated
image, and this resumed kernel will also try to reload the GuC firmware
(which will fail). To recover, we reset the GuC and try again (which
should work). But this GuC reset doesn't also reset the doorbell
hardware, so it can be left in a state inconsistent with that assumed
by the driver and/or the newly-loaded GuC firmware.
It would be better if the GuC reset also cleared all doorbell state,
but that's not how the hardware currently works; also, the driver cannot
directly reprogram the doorbell hardware (only the GuC can do that).
So this patch cycles through all doorbells, assigning and releasing each
in turn, so that all the doorbell hardware is left in a consistent
state, no matter how it was programmed by the previously-running kernel
and/or GuC firmware.
v2: don't use kmap_atomic() now that client page 0 is kept mapped.
Dave Gordon [Mon, 13 Jun 2016 16:57:33 +0000 (17:57 +0100)]
drm/i915/guc: replace assign_doorbell() with select_doorbell_register()
This version doesn't update the doorbell bitmap, as that will
be done when the selected doorbell is associated with a client.
The call is now slightly earlier, just on the general principle
that potentially-failing operations should be done as early as
possible, to eliminate late failures and simplify recovery.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Mon, 13 Jun 2016 16:57:32 +0000 (17:57 +0100)]
drm/i915/guc: refactor doorbell management code
This patch refactors the driver's handling and tracking of doorbells, in
preparation for a later one which will resolve a suspend-resume issue.
There are three resources to be managed:
1. Cachelines: a single line within the client-object's page 0
is snooped by doorbell hardware for writes from the host.
2. Doorbell registers: each defines one cacheline to be snooped.
3. Bitmap: tracks which doorbell registers are in use.
The doorbell setup/teardown protocol starts with:
1. Pick a cacheline: select_doorbell_cacheline()
2. Find an available doorbell register: assign_doorbell()
(These values are passed to the GuC via the shared context
descriptor; this part of the sequence remains unchanged).
3. Update the bitmap to reflect registers-in-use
4. Prepare the cacheline for use by setting its status to ENABLED
5. Ask the GuC to program the doorbell to snoop the cacheline
and of course teardown is very similar:
6. Set the cacheline to DISABLED
7. Ask the GuC to reprogram the doorbell to stop snooping
8. Record that the doorbell is not in use.
Operations 6-8 (guc_disable_doorbell(), host2guc_release_doorbell(), and
release_doorbell()) were called in sequence from guc_client_free(), but
are now moved into the teardown phase of the common function.
Steps 4-5 (guc_init_doorbell() and host2guc_allocate_doorbell()) were
similarly done as sequential steps in guc_client_alloc(), but since it
turns out that we don't need to be able to do them separately they're
now collected into the setup phase of the common function.
The only new code (and new capability) is the block tagged
/* Update the GuC's idea of the doorbell ID */
i.e. we can now *change* the doorbell register used by an existing
client, whereas previously it was set once for the entire lifetime
of the client. We will use this new feature in the next patch.
v2: Trivial independent fixes pushed ahead as separate patches.
MUCH longer commit message :) [Tvrtko Ursulin]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Mon, 13 Jun 2016 16:57:31 +0000 (17:57 +0100)]
drm/i915/guc: move guc_ring_doorbell() nearer to callsite
Just code movement, no actual change to the function. This is in
preparation for the next patch, which will reorganise all the other
doorbell code, but doesn't change this function. So let's shuffle it
down near its caller rather than leaving it mixed in with the setup
code. Unlike the doorbell management code, this function is somewhat
time-critical, so putting it near its caller may even yield a tiny
performance improvement.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Mon, 13 Jun 2016 16:57:28 +0000 (17:57 +0100)]
drm/i915/guc: add doorbell map to debugfs/i915_guc_info
To properly verify the driver->doorbell->GuC functionality, validation
needs to know how the driver has assigned the doorbell cache lines and
registers, so make them visible through debugfs.
v2: use kernel bitmap-printing format (%pb) rather than %x.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Pooled EU is enabled by default for BXT but for fused down 2x6 parts it is
advised to turn it off. But there is another HW issue in these parts (fused
down 2x6 parts) before C0 that requires Pooled EU to be enabled as a
workaround. In this case the pool configuration changes depending upon
which subslice is disabled. This doesn't affect if the device has all 3
subslices enabled.
Userspace need to know min no. of eus in a pool as it varies based on which
subslice is disabled, this is not yet exported because userspace support is
not available yet. Once the support is available this needs to be exported
using getparam ioctls.
v2: s/subslice_total/subslice_per_slice as it is a more logical field (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Winiarski, Michal <michal.winiarski@intel.com> Cc: Zou, Nanhai <nanhai.zou@intel.com> Cc: Yang, Rong R <rong.r.yang@intel.com> Cc: Tim Gore <tim.gore@intel.com> Cc: Jeff McGee <jeff.mcgee@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This mode allows to assign EUs to pools which can process work collectively.
The command to enable this mode should be issued as part of context initialization.
The pooled mode is global, once enabled it has to stay the same across all
contexts until HW reset hence this is sent in auxiliary golden context batch.
Thanks to Mika for the preliminary review and comments.
v2: explain why this is enabled in golden context, use feature flag while
enabling the support (Chris)
v3: Include only kernel support as userspace support is not available yet.
User space clients need to know when the pooled EU feature is present
and enabled on the hardware so that they can adapt work submissions.
Create a new device info flag for this purpose.
Set has_pooled_eu to true in the Broxton static device info - Broxton
supports the feature in hardware and the driver will enable it by
default.
We need to add getparam ioctls to enable userspace to query availability of
this feature and to retrieve min. no of eus in a pool but we will expose
them once userspace support is available. Opensource users for this feature
are mesa, libva and beignet.
Beignet team is currently working on adding userspace support.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2) Cc: Winiarski, Michal <michal.winiarski@intel.com> Cc: Zou, Nanhai <nanhai.zou@intel.com> Cc: Yang, Rong R <rong.r.yang@intel.com> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Armin Reese <armin.c.reese@intel.com> Cc: Tim Gore <tim.gore@intel.com> Signed-off-by: Jeff McGee <jeff.mcgee@intel.com> Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com> Reviewed-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Fri, 10 Jun 2016 17:29:26 +0000 (18:29 +0100)]
drm/i915/guc: prefer 'dev_priv' to 'dev' for intra-module functions
There are four non-static functions in i915_guc_submission.c that take a
'dev' parameter. All are called only from GuC loader code, and can be
easily converted to accept 'dev_priv' instead.
Dave Gordon [Fri, 10 Jun 2016 17:29:25 +0000 (18:29 +0100)]
drm/i915/guc: prefer 'dev_priv' to 'dev' for static functions
Convert all static functions in i915_guc_submission.c that currently
take a 'dev' pointer to take 'dev_priv' instead (there are three,
guc_client_alloc(), guc_client_free(), and gem_allocate_guc_obj().
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Imre Deak [Mon, 13 Jun 2016 13:44:37 +0000 (16:44 +0300)]
drm/i915/bxt: Sanitiy check the PHY lane power down status
We can check the power state of the PHY data and common lanes as
reported by the PHY. Do this in case we need to debug problems where the
PHY gets stuck in an unexpected state.
Note that I only check these when the lanes are expected to be powered
on purpose, since it's not clear at what point the PHY power/clock gates
things.
v2:
- Don't report the encoder as disabled when the sanity check fails.
(Ville)
Imre Deak [Mon, 13 Jun 2016 13:44:35 +0000 (16:44 +0300)]
drm/i915/bxt: Set DDI PHY lane latency optimization during modeset
So far we configured a static lane latency optimization during driver
loading/resuming. The specification changed at one point and now this
configuration depends on the lane count, so move the configuration
to modeset time accordingly.
It's not clear when this lane configuration takes effect. The
specification only requires that the programming is done before enabling
the port. On CHV OTOH the lanes start to power up already right after
enabling the PLL. To be safe preserve the current order and set things
up already before enabling the PLL.
v2: (Ander)
- Simplify the optimization mask calculation.
- Use the correct pipe_config always during the calculation instead
of the bogus intel_crtc->config.
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95476 Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Imre Deak [Mon, 13 Jun 2016 13:44:34 +0000 (16:44 +0300)]
drm/i915/bxt: Move DDI PHY enabling/disabling to the power well code
So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Imre Deak [Mon, 13 Jun 2016 13:44:33 +0000 (16:44 +0300)]
drm/i915: Factor out intel_power_well_get/put
These helpers will be needed by the next patch, so factor them out.
No functional change.
v2:
- Move the refcount==0 WARN to the new put helper. (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Imre Deak [Mon, 13 Jun 2016 13:44:32 +0000 (16:44 +0300)]
drm/i915/bxt: Wait for PHY1 GRC calibration synchronously
A follow-up patch moves the PHY enabling to the power well code where
enabling/disabling the PHYs will happen independently. Because of this
waiting for the GRC calibration in PHY1 asynchronously would need some
additional logic. Instead of adding that let's keep things simple for now
and wait synchronously. My measurements showed that the calibration
takes ~4ms.
Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Alexey Brodkin [Mon, 6 Jun 2016 07:56:53 +0000 (10:56 +0300)]
ARC: [nsimosci] Enable ARC PGU on nSIM OSCI virtual platforms
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Ruud Derwig [Mon, 6 Jun 2016 07:47:46 +0000 (10:47 +0300)]
drm/arcpgu: Make ARC PGU usable on simulation platforms
In case of simulation there's no real encoder/transmitter device
because in the model's virtual LCD we're rendering whatever
appears in frame-buffer memory.
Rob Clark [Thu, 9 Jun 2016 19:29:19 +0000 (15:29 -0400)]
drm/prime: fix error path deadlock fail
There were a couple messed up things about this fail path.
(1) it would drop object_name_lock twice
(2) drm_gem_handle_delete() (in drm_gem_remove_prime_handles())
needs to grab prime_lock
Lukas Wunner [Wed, 8 Jun 2016 11:15:22 +0000 (13:15 +0200)]
drm/i915: Don't unregister fbdev's fb twice
Calling drm_framebuffer_unregister_private() in intel_fbdev_destroy() is
superfluous because the framebuffer will subsequently be unregistered by
drm_framebuffer_free() when unreferenced in drm_framebuffer_remove().
The call is a leftover, when it was introduced by commit 362063619cf6
("drm: revamp framebuffer cleanup interfaces"), struct intel_framebuffer
was still embedded in struct intel_fbdev rather than being a pointer as
it is today, and drm_framebuffer_remove() wasn't used yet.
As a bonus, the ID of the framebuffer is no longer 0 in the debug log:
This patch enables a workaround for a mid thread preemption
issue where a hardware timing problem can prevent the
context restore from happening, leading to a hang.
v2: move to gen9_init_workarounds (Arun)
v3: move to start of gen9_init_workarounds (Arun)
drm/i915: Support for pread/pwrite from/to non shmem backed objects
This patch adds support for extending the pread/pwrite functionality
for objects not backed by shmem. The access will be made through
gtt interface. This will cover objects backed by stolen memory as well
as other non-shmem backed objects.
v2: Drop locks around slow_user_access, prefault the pages before
access (Chris)
v3: Rebased to the latest drm-intel-nightly (Ankit)
v4: Moved page base & offset calculations outside the copy loop,
corrected data types for size and offset variables, corrected if-else
braces format (Tvrtko/kerneldocs)
v5: Enabled pread/pwrite for all non-shmem backed objects including
without tiling restrictions (Ankit)
v6: Using pwrite_fast for non-shmem backed objects as well (Chris)
v7: Updated commit message, Renamed i915_gem_gtt_read to i915_gem_gtt_copy,
added pwrite slow path for non-shmem backed objects (Chris/Tvrtko)
v8: Updated v7 commit message, mutex unlock around pwrite slow path for
non-shmem backed objects (Tvrtko)
v9: Corrected check during pread_ioctl, to avoid shmem_pread being
called for non-shmem backed objects (Tvrtko)
v10: Moved the write_domain check to needs_clflush and tiling mode check
to pwrite_fast (Chris)
v11: Use pwrite_fast fallback for all objects (shmem and non-shmem backed),
call fast_user_write regardless of pagefault in previous iteration
v12: Use page-by-page copy for slow user access too (Chris)
v13: Handled EFAULT, Avoid use of WARN_ON, put_fence only if whole obj
pinned (Chris)
In pwrite_fast, map an object page by page if obj_ggtt_pin fails. First,
we try a nonblocking pin for the whole object (since that is fastest if
reused), then failing that we try to grab one page in the mappable
aperture. It also allows us to handle objects larger than the mappable
aperture (e.g. if we need to pwrite with vGPU restricting the aperture
to a measely 8MiB or something like that).
v2: Pin pages before starting pwrite, Combined duplicate loops (Chris)
v3: Combined loops based on local patch by Chris (Chris)
v4: Added i915 wrapper function for drm_mm_insert_node_in_range (Chris)
v5: Renamed wrapper function for drm_mm_insert_node_in_range (Chris)
v5: Added wrapper for drm_mm_remove_node() (Chris)
v6: Added get_pages call before pinning the pages (Tvrtko)
Added remove_mappable_node() wrapper for drm_mm_remove_node() (Chris)
v7: Added size argument for insert_mappable_node (Tvrtko)
v8: Do not put_pages after pwrite, do memset of node in the wrapper
function (insert_mappable_node) (Chris)
v9: Rebase (Ankit)
Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
This utility function is a companion to i915_gem_object_get_page() that
uses the same cached iterator for the scatterlist to perform fast
sequential lookup of the dma address associated with any page within the
object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Chris Wilson [Fri, 10 Jun 2016 08:52:59 +0000 (14:22 +0530)]
drm/i915: Add support for mapping an object page by page
Introduced a new vm specfic callback insert_page() to program a single pte in
ggtt or ppgtt. This allows us to map a single page in to the mappable aperture
space. This can be iterated over to access the whole object by using space as
meagre as page size.
v2: Added low level rpm assertions to insert_page routines (Chris)
v3: Added POSTING_READ post register write (Tvrtko)
v4: Rebase (Ankit)
v5: Removed wmb() and FLUSH_CTL from insert_page, caller to take care
of it (Chris)
v6: insert_page not working correctly without FLSH_CNTL write, added the
write again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Ankitprasad Sharma <ankitprasad.r.sharma@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Fri, 10 Jun 2016 16:21:25 +0000 (17:21 +0100)]
drm/i915/guc: suppress GuC-related message on non-GuC platforms
If the user doesn't override the default values of the GuC-related
kernel parameters, then on a non-GuC-based platform we shouldn't
mention that we haven't loaded the GuC firmware.
The various messages have been reordered into a least->most severe
cascade (none/INFO/INFO/ERROR) for ease of comprehension.
Thierry Reding [Fri, 3 Jun 2016 12:23:00 +0000 (14:23 +0200)]
drm/dsi: Add uevent callback
Implement a uevent callback for devices on the MIPI DSI bus. This
callback will append MODALIAS information to the uevent and allow
modules to be loaded when devices are added to the bus.
Sudip Mukherjee [Sun, 12 Jun 2016 15:03:56 +0000 (16:03 +0100)]
drm: fb: cma: fix memory leak
We may have a situation that the memory allocation for fbdefio fails
and then the allocation for fbops may succeed as some memory has been
freed somewhere. Lets free fbops also to face these rare situtation.
Since kfree can handle arguments as NULL, there should not be any
problem in calling both the kfree().
Boris Brezillon [Tue, 7 Jun 2016 11:48:01 +0000 (13:48 +0200)]
drm: i915: Rely on the default ->best_encoder() behavior where appropriate
For all outputs except dp_mst, we have a 1:1 relationship between
connectors and encoders and the driver is relying on the atomic helpers:
we can drop the custom ->best_encoder() implementation and let the core
call drm_atomic_helper_best_encoder() for us.
Noralf Trønnes [Fri, 10 Jun 2016 14:55:59 +0000 (16:55 +0200)]
drm: Add helper for simple display pipeline
Provides helper functions for drivers that have a simple display
pipeline. Plane, crtc and encoder are collapsed into one entity.
Changes since v4:
- Remove drm_connector_register() call
- Forgot to assign pipe->connector
Changes since v3:
- (struct drm_simple_display_pipe *)->funcs should be const
Changes since v2:
- Drop Kconfig knob DRM_KMS_HELPER
- Expand documentation
Changes since v1:
- Add DOC header and add to gpu.tmpl
- Fix docs: @funcs is optional, "negative error code",
"This hook is optional."
- Add checks to drm_simple_kms_plane_atomic_check()
Boris Brezillon [Tue, 7 Jun 2016 11:48:15 +0000 (13:48 +0200)]
drm/bridge: dw-hdmi: Use drm_atomic_helper_best_encoder()
We have a 1:1 relationship between connectors and encoders, which means
we can rely on the drm_atomic_helper_best_encoder() behavior.
We still have to explicitly assign ->best_encoder() to
drm_atomic_helper_best_encoder(), because the automated fallback to
drm_atomic_helper_best_encoder() when ->best_encoder() is NULL is only
available when the DRM device is using the atomic helpers, and this bridge
is compatible with non-atomic and atomic devices.
Boris Brezillon [Tue, 7 Jun 2016 11:48:14 +0000 (13:48 +0200)]
drm/bridge: ps8622: Rely on the default ->best_encoder() behavior
We have a 1:1 relationship between connectors and encoders, and the driver
is relying on the atomic helpers: we can drop the custom ->best_encoder(),
and let the core call drm_atomic_helper_best_encoder() for us.
Boris Brezillon [Tue, 7 Jun 2016 11:48:13 +0000 (13:48 +0200)]
drm/bridge: ptn3460: Rely on the default ->best_encoder() behavior
We have a 1:1 relationship between connectors and encoders, and the driver
is relying on the atomic helpers: we can drop the custom ->best_encoder(),
and let the core call drm_atomic_helper_best_encoder() for us.
Boris Brezillon [Tue, 7 Jun 2016 11:48:12 +0000 (13:48 +0200)]
drm/bridge: anx78xx: Rely on the default ->best_encoder() behavior
We have a 1:1 relationship between connectors and encoders, and the driver
is relying on the atomic helpers: we can drop the custom ->best_encoder(),
and let the core call drm_atomic_helper_best_encoder() for us.
Boris Brezillon [Tue, 7 Jun 2016 11:48:11 +0000 (13:48 +0200)]
drm: omap: Rely on the default ->best_encoder() behavior
We have a 1:1 relationship between connectors and encoders and the
driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementation and let the core call
drm_atomic_helper_best_encoder() for us.
Boris Brezillon [Tue, 7 Jun 2016 11:48:10 +0000 (13:48 +0200)]
drm: virtgpu: Rely on the default ->best_encoder() behavior
The virtgpu output exposes a 1:1 relationship between connectors and
encoders and the driver is relying on the atomic helpers: we can drop
the custom ->best_encoder() implementation and let the core call
drm_atomic_helper_best_encoder() for us.
projects / kernel.git / log