Vladimir Oltean [Sun, 22 May 2022 09:50:38 +0000 (12:50 +0300)]
selftests: ocelot: tc_flower_chains: streamline test output
Bring this driver-specific selftest output in line with the other
selftests.
Before:
Testing VLAN pop.. OK
Testing VLAN push.. OK
Testing ingress VLAN modification.. OK
Testing egress VLAN modification.. OK
Testing frame prioritization.. OK
After:
TEST: VLAN pop [ OK ]
TEST: VLAN push [ OK ]
TEST: Ingress VLAN modification [ OK ]
TEST: Egress VLAN modification [ OK ]
TEST: Frame prioritization [ OK ]
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 19 May 2022 20:20:54 +0000 (13:20 -0700)]
net: wrap the wireless pointers in struct net_device in an ifdef
Most protocol-specific pointers in struct net_device are under
a respective ifdef. Wireless is the notable exception. Since
there's a sizable number of custom-built kernels for datacenter
workloads which don't build wireless it seems reasonable to
ifdefy those pointers as well.
While at it move IPv4 and IPv6 pointers up, those are special
for obvious reasons.
Acked-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> # ieee802154 Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Fri, 20 May 2022 06:26:50 +0000 (08:26 +0200)]
net: fec: Do proper error checking for enet_out clk
An error code returned by devm_clk_get() might have other meanings than
"This clock doesn't exist". So use devm_clk_get_optional() and handle
all remaining errors as fatal.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Tommaso Merciai [Fri, 20 May 2022 23:58:46 +0000 (01:58 +0200)]
net: phy: DP83822: enable rgmii mode if phy_interface_is_rgmii
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
Signed-off-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com> Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Suggested-by: Alberto Bianchi <alberto.bianchi@amarulasolutions.com> Tested-by: Tommaso Merciai <tommaso.merciai@amarulasolutions.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: selftests: Add stress_reuseport_listen to .gitignore
Add newly added stress_reuseport_listen object to .gitignore file.
Fixes: 52921b9c461c ("net: selftests: Stress reuseport listen") Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 22 May 2022 20:03:02 +0000 (21:03 +0100)]
Merge branch 'rxrpc-misc'
David Howells says:
====================
rxrpc: Miscellaneous changes
Here are some miscellaneous changes for AF_RXRPC:
(1) Allow the list of local endpoints to be viewed through /proc.
(2) Switch to using refcount_t for refcounting.
(3) Fix a locking issue found by lockdep.
(4) Autogenerate tracing symbol enums from symbol->string maps to make it
easier to keep them in sync.
(5) Return an error to sendmsg() if a call it tried to set up failed.
Because it failed at this point, no notification will be generated for
recvmsg to pick up - but userspace still needs to know about the
failure.
(6) Fix the selection of abort codes generated by internal events. In
particular, rxrpc and kafs shouldn't be generating RX_USER_ABORT
unless it's because userspace did something to cancel a call.
(7) Adjust the interpretation and handling of certain ACK types to try and
detect NAT changes causing a call to seem to start mid-flow from a
different peer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 21 May 2022 07:45:55 +0000 (08:45 +0100)]
afs: Adjust ACK interpretation to try and cope with NAT
If a client's address changes, say if it is NAT'd, this can disrupt an in
progress operation. For most operations, this is not much of a problem,
but StoreData can be different as some servers modify the target file as
the data comes in, so if a store request is disrupted, the file can get
corrupted on the server.
The problem is that the server doesn't recognise packets that come after
the change of address as belonging to the original client and will bounce
them, either by sending an OUT_OF_SEQUENCE ACK to the apparent new call if
the packet number falls within the initial sequence number window of a call
or by sending an EXCEEDS_WINDOW ACK if it falls outside and then aborting
it. In both cases, firstPacket will be 1 and previousPacket will be 0 in
the ACK information.
Fix this by the following means:
(1) If a client call receives an EXCEEDS_WINDOW ACK with firstPacket as 1
and previousPacket as 0, assume this indicates that the server saw the
incoming packets from a different peer and thus as a different call.
Fail the call with error -ENETRESET.
(2) Also fail the call if a similar OUT_OF_SEQUENCE ACK occurs if the
first packet has been hard-ACK'd. If it hasn't been hard-ACK'd, the
ACK packet will cause it to get retransmitted, so the call will just
be repeated.
(3) Make afs_select_fileserver() treat -ENETRESET as a straight fail of
the operation.
(4) Prioritise the error code over things like -ECONNRESET as the server
did actually respond.
(5) Make writeback treat -ENETRESET as a retryable error and make it
redirty all the pages involved in a write so that the VM will retry.
Note that there is still a circumstance that I can't easily deal with: if
the operation is fully received and processed by the server, but the reply
is lost due to address change. There's no way to know if the op happened.
We can examine the server, but a conflicting change could have been made by
a third party - and we can't tell the difference. In such a case, a
message like:
will be logged to dmesg on the next op to touch the file and the client
will reset the inode state, including invalidating clean parts of the
pagecache.
David Howells [Sat, 21 May 2022 07:45:48 +0000 (08:45 +0100)]
rxrpc, afs: Fix selection of abort codes
The RX_USER_ABORT code should really only be used to indicate that the user
of the rxrpc service (ie. userspace) implicitly caused a call to be aborted
- for instance if the AF_RXRPC socket is closed whilst the call was in
progress. (The user may also explicitly abort a call and specify the abort
code to use).
Change some of the points of generation to use other abort codes instead:
(1) Abort the call with RXGEN_SS_UNMARSHAL or RXGEN_CC_UNMARSHAL if we see
ENOMEM and EFAULT during received data delivery and abort with
RX_CALL_DEAD in the default case.
(2) Abort with RXGEN_SS_MARSHAL if we get ENOMEM whilst trying to send a
reply.
(3) Abort with RX_CALL_DEAD if we stop hearing from the peer if we had
heard from the peer and abort with RX_CALL_TIMEOUT if we hadn't.
(4) Abort with RX_CALL_DEAD if we try to disconnect a call that's not
completed successfully or been aborted.
Reported-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 21 May 2022 07:45:41 +0000 (08:45 +0100)]
rxrpc: Return an error to sendmsg if call failed
If at the end of rxrpc sendmsg() or rxrpc_kernel_send_data() the call that
was being given data was aborted remotely or otherwise failed, return an
error rather than returning the amount of data buffered for transmission.
The call (presumably) did not complete, so there's not much point
continuing with it. AF_RXRPC considers it "complete" and so will be
unwilling to do anything else with it - and won't send a notification for
it, deeming the return from sendmsg sufficient.
Not returning an error causes afs to incorrectly handle a StoreData
operation that gets interrupted by a change of address due to NAT
reconfiguration.
This doesn't normally affect most operations since their request parameters
tend to fit into a single UDP packet and afs_make_call() returns before the
server responds; StoreData is different as it involves transmission of a
lot of data.
This can be triggered on a client by doing something like:
The Auristor fileserver logs code -453 (RXGEN_SS_UNMARSHAL), but the abort
code received by kafs is -5 (RX_PROTOCOL_ERROR) as the rx layer sees the
condition and generates an abort first and the unmarshal error is a
consequence of that at the application layer.
David Howells [Sat, 21 May 2022 07:45:35 +0000 (08:45 +0100)]
rxrpc: Automatically generate trace tag enums
Automatically generate trace tag enums from the symbol -> string mapping
tables rather than having the enums as well, thereby reducing duplicated
data.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 21 May 2022 07:45:28 +0000 (08:45 +0100)]
rxrpc: Fix locking issue
There's a locking issue with the per-netns list of calls in rxrpc. The
pieces of code that add and remove a call from the list use write_lock()
and the calls procfile uses read_lock() to access it. However, the timer
callback function may trigger a removal by trying to queue a call for
processing and finding that it's already queued - at which point it has a
spare refcount that it has to do something with. Unfortunately, if it puts
the call and this reduces the refcount to 0, the call will be removed from
the list. Unfortunately, since the _bh variants of the locking functions
aren't used, this can deadlock.
================================
WARNING: inconsistent lock state
5.18.0-rc3-build4+ #10 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/2/25 [HC0[0]:SC1[1]:HE1:SE0] takes: ffff888107ac4038 (&rxnet->call_lock){+.?.}-{2:2}, at: rxrpc_put_call+0x103/0x14b
{SOFTIRQ-ON-W} state was registered at:
...
Possible unsafe locking scenario:
1 lock held by ksoftirqd/2/25:
#0: ffff8881008ffdb0 ((&call->timer)){+.-.}-{0:0}, at: call_timer_fn+0x5/0x23d
Changes
=======
ver #2)
- Changed to using list_next_rcu() rather than rcu_dereference() directly.
Fixes: 81566af9fe72 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 21 May 2022 07:45:22 +0000 (08:45 +0100)]
rxrpc: Use refcount_t rather than atomic_t
Move to using refcount_t rather than atomic_t for refcounts in rxrpc.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Sat, 21 May 2022 07:45:15 +0000 (08:45 +0100)]
rxrpc: Allow list of in-use local UDP endpoints to be viewed in /proc
Allow the list of in-use local UDP endpoints in the current network
namespace to be viewed in /proc.
To aid with this, the endpoint list is converted to an hlist and RCU-safe
manipulation is used so that the list can be read with only the RCU
read lock held.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 22 May 2022 19:46:13 +0000 (20:46 +0100)]
Merge branch 'ipa-next'
Alex Elder says:
====================
net: ipa: a few more small items
This series consists of three small sets of changes. Version 2 adds
a patch that avoids a warning that occurs when handling a modem
crash (I unfortunately didn't notice it earlier). All other patches
are the same--just rebased.
The first three patches allow a few endpoint features to be
specified. At this time, currently-defined endpoints retain the
same configuration, but when the monitor functionality is added in
the next cycle these options will be required.
The fourth patch simply removes an unused function, explaining also
why it would likely never be used.
The fifth patch is new. It counts the number of modem TX endpoints
and uses it to determine how many TREs a transaction needs when
when handling a modem crash. It is needed to avoid exceeding the
limited number of commands imposed by the last four patches.
And the last four patches refactor code related to IPA immediate
commands, eliminating an unused field and then simplifying and
removing some unneeded code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:23 +0000 (19:32 -0500)]
net: ipa: use data space for command opcodes
The 64-bit data field in a transaction is not used for commands.
And the opcode array is *only* used for commands. They're
(currently) the same size; save a little space in the transaction
structure by enclosing the two fields in a union.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:22 +0000 (19:32 -0500)]
net: ipa: remove command info pool
The ipa_cmd_info structure now contains only one field, and it's an
enumerated type whose values all fit in 8 bits. Currently we'll
never use more than 8 TREs in a command transaction, and we can
represent that number of command opcodes in the same space as a 64
bit pointer to an ipa_cmd_info structure.
Define IPA_COMMAND_TRANS_TRE_MAX as the maximum number of TREs that
can be in a command transaction. Replace the info pointer in a
transaction with a fixed-size array named cmd_opcode[] of that many
bytes. Store the opcode in this array when adding a command TRE to
a transaction, as was done previously for the info array. This
makes the ipa_cmd_info unused, so get rid of it.
When committing an immediate command transaction, use the channel's
Boolean command flag to determine whether to fill in the opcode,
which will be taken (as before) from the array in the transaction.
This makes the command info pool unnecessary, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:20 +0000 (19:32 -0500)]
net: ipa: get rid of ipa_cmd_info->direction
The direction field of the ipa_cmd_info structure is set, but never
used. It seems it might have been used for the DMA_SHARED_MEM
immediate command, but the DIRECTION flag is set based on the value
of the passed-in direction flag there.
Anyway, remove this unused field from the ipa_cmd_info structure.
This is done as a separate patch to make it very obvious that it's
not required.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:19 +0000 (19:32 -0500)]
net: ipa: count the number of modem TX endpoints
In ipa_endpoint_modem_exception_reset_all(), a high estimate was
made of the number of endpoints that need their status register
updated. We only used what was needed, so the high estimate didn't
matter much.
However the next few patches are going to limit the number of
commands in a single transaction, and the overestimate would exceed
that. So count the number of modem TX endpoints at initialization
time, and use it in ipa_endpoint_modem_exception_reset_all().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:18 +0000 (19:32 -0500)]
net: ipa: kill gsi_trans_commit_wait_timeout()
Since the beginning gsi_trans_commit_wait_timeout() has existed to
provide a way to allow waiting a limited time for a transaction
to complete. But that function has never been used.
In fact, there is no use for this function, because a transaction
committed to hardware should *always* complete. The only reason it
might not complete is if there were a hardware failure, or perhaps a
system configuration error.
Furthermore, if a timeout ever did occur, the IPA hardware would be
in an indeterminate state, from which there is no recovery. It
would require some sort of complete IPA reset, and would require the
participation of the modem, and at this time there is no such
sequence defined.
So get rid of the definition of gsi_trans_commit_wait_timeout(), and
update a few comments accordingly.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:17 +0000 (19:32 -0500)]
net: ipa: specify RX aggregation time limit in config data
Don't assume that a 500 microsecond time limit should be used for
all receive endpoints that support aggregation. Instead, specify
the time limit to use in the configuration data.
Set a 500 microsecond limit for all existing RX endpoints, as before.
Checking for overflow for the time limit field is a bit complicated.
Rather than duplicate a lot of code in ipa_endpoint_data_valid_one(),
call WARN() if any value is found to be too large when encoding it.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:16 +0000 (19:32 -0500)]
net: ipa: support hard aggregation limits
Add a new flag for AP receive endpoints that indicates whether
a "hard limit" is used as a criterion for closing aggregation.
Add comments explaining the difference between "hard" and "soft"
aggregation limits.
Pass a flag to ipa_aggr_size_kb() so it computes the proper
aggregation size value whether using hard or soft limits. Move
that function earlier in "ipa_endpoint.c" so it can be used
without a forward-reference.
Update ipa_endpoint_data_valid_one() so it validates endpoints whose
data indicate a hard aggregation limit is used, and so it reports
set aggregation flags for endpoints without aggregation enabled.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Sun, 22 May 2022 00:32:15 +0000 (19:32 -0500)]
net: ipa: make endpoint HOLB drop configurable
Add a new Boolean flag for RX endpoints defining whether HOLB drop
is initially enabled or disabled for the endpoint. All existing AP
endpoints should have HOLB drop disabled.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sat, 21 May 2022 11:11:23 +0000 (13:11 +0200)]
nfp: flower: fix typo in comment
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Add a bhash2 table hashed by port + address
This patchset proposes adding a bhash2 table that hashes by port and address.
The motivation behind bhash2 is to expedite bind requests in situations where
the port has many sockets in its bhash table entry, which makes checking bind
conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.
We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine
The patches are as follows:
1/2 - Adds a second bhash table (bhash2) hashed by port and address
2/2 - Adds a test for timing how long an additional bind request takes when
the bhash entry is populated
When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000018 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
====================
Joanne Koong [Fri, 20 May 2022 00:18:34 +0000 (17:18 -0700)]
selftests: Add test for timing a bind request to a port with a populated bhash entry
This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.
When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).
To run the test locally, I did:
* ulimit -n 65535000
* ip addr add 2001:0db8:0:f101::1 dev eth0
* ./bind_bhash_test 443
Signed-off-by: Joanne Koong <joannelkoong@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Joanne Koong [Fri, 20 May 2022 00:18:33 +0000 (17:18 -0700)]
net: Add a second bind table hashed by port and address
We currently have one tcp bind table (bhash) which hashes by port
number only. In the socket bind path, we check for bind conflicts by
traversing the specified port's inet_bind2_bucket while holding the
bucket's spinlock (see inet_csk_get_port() and inet_csk_bind_conflict()).
In instances where there are tons of sockets hashed to the same port
at different addresses, checking for a bind conflict is time-intensive
and can cause softirq cpu lockups, as well as stops new tcp connections
since __inet_inherit_port() also contests for the spinlock.
This patch proposes adding a second bind table, bhash2, that hashes by
port and ip address. Searching the bhash2 table leads to significantly
faster conflict resolution and less time holding the spinlock.
Signed-off-by: Joanne Koong <joannelkoong@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 May 2022 07:09:21 +0000 (10:09 +0300)]
selftests: fib_nexthops: Make ping timeout configurable
Commit cdf7619fd019 ("selftests: fib_nexthops: Make the test more robust")
increased the timeout of ping commands to 5 seconds, to make the test
more robust. Make the timeout configurable using '-w' argument to allow
user to change it depending on the system that runs the test. Some systems
suffer from slow forwarding performance, so they may need to change the
timeout.
Jakub Kicinski [Wed, 18 May 2022 18:55:22 +0000 (11:55 -0700)]
net: avoid strange behavior with skb_defer_max == 1
When user sets skb_defer_max to 1 the kick threshold is 0
(half of 1). If we increment queue length before the check
the kick will never happen, and the skb may get stranded.
This is likely harmless but can be avoided by moving the
increment after the check. This way skb_defer_max == 1
will always kick. Still a silly config to have, but
somehow that feels more correct.
While at it drop a comment which seems to be outdated
or confusing, and wrap the defer_count write with
a WRITE_ONCE() since it's read on the fast path
that avoids taking the lock.
Martin Habets [Thu, 19 May 2022 07:17:15 +0000 (08:17 +0100)]
sfc/siena: Remove duplicate check on segments
Siena only supports software TSO. This means more code can be deleted,
as pointed out by the Smatch static checker warning:
drivers/net/ethernet/sfc/siena/tx.c:184 __efx_siena_enqueue_skb()
warn: duplicate check 'segments' (previous on line 158)
Jakub Kicinski [Fri, 20 May 2022 02:13:47 +0000 (19:13 -0700)]
tcp_ipv6: set the drop_reason in the right place
Looks like the IPv6 version of the patch under Fixes was
a copy/paste of the IPv4 but hit the wrong spot.
It is tcp_v6_rcv() which uses drop_reason as a boolean, and
needs to be protected against reason == 0 before calling free.
tcp_v6_do_rcv() has a pretty straightforward flow.
The resulting warning looks like this:
WARNING: CPU: 1 PID: 0 at net/core/skbuff.c:775
Call Trace:
tcp_v6_rcv (net/ipv6/tcp_ipv6.c:1767)
ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:438)
ip6_input_finish (include/linux/rcupdate.h:726)
ip6_input (include/linux/netfilter.h:307)
Fixes: e4cbe5f80dc3 ("net: tcp: reset 'drop_reason' to NOT_SPCIFIED in tcp_v{4,6}_rcv()") Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20220520021347.2270207-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Fri, 20 May 2022 10:12:24 +0000 (11:12 +0100)]
Merge branch 'net-ipa-next'
Alex Elder says:
====================
net: ipa: a mix of patches
This series includes a mix of things things that are generally
minor. The first four are sort of unrelated fixes, and summarizing
them here wouldn't be that helpful.
The last three together make it so only the "configuration data" we
need after initialization is saved for later use. Most such data is
used only during driver initialization. But endpoint configuration
is needed later, so the last patch saves a copy of that. Eventually
we'll want to support reconfiguring endpoints at runtime as well,
and this will facilitate that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:17 +0000 (10:12 -0500)]
net: ipa: save a copy of endpoint default config
All elements of the default endpoint configuration are used in the
code when programming an endpoint for use. But none of the other
configuration data is ever needed once things are initialized.
So rather than saving a pointer to *all* of the configuration data,
save a copy of only the endpoint configuration portion.
This will eventually allow endpoint configuration to be modifiable
at runtime. But even before that it means we won't keep a pointer
to configuration data after when no longer needed.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:16 +0000 (10:12 -0500)]
net: ipa: rename a few endpoint config data types
Rename the just-moved data structure types to drop the "_data"
suffix, to make it more obvious they are no longer meant to be used
just as read-only initialization data. Rename the fields and
variables of these types to use "config" instead of "data" in the
name. This is another small step meant to facilitate review.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:15 +0000 (10:12 -0500)]
net: ipa: move endpoint configuration data definitions
Move the definitions of the structures defining endpoint-specific
configuration data out of "ipa_data.h" and into "ipa_endpoint.h".
This is a trivial movement of code without any other change, to
prepare for the next few patches.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:14 +0000 (10:12 -0500)]
net: ipa: open-code ether_setup()
About half of the fields set by the call in ipa_modem_netdev_setup()
are overwritten after the call. Instead, just skip the call, and
open-code the (other) assignments it makes to the net_device
structure fields.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:13 +0000 (10:12 -0500)]
net: ipa: ignore endianness if there is no header
If we program an RX endpoint to have no header (header length is 0),
header-related endpoint configuration values are meaningless and are
ignored.
The only case we support that defines a header is QMAP endpoints.
In ipa_endpoint_init_hdr_ext() we set the endianness mask value
unconditionally, but it should not be done if there is no header
(meaning it is not configured for QMAP).
Set the endianness conditionally, and rearrange the logic in that
function slightly to avoid testing the qmap flag twice.
Delete an incorrect comment in ipa_endpoint_init_aggr().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Thu, 19 May 2022 15:12:11 +0000 (10:12 -0500)]
net: ipa: drop an unneeded transaction reference
In gsi_channel_update(), a reference count is taken on the last
completed transaction "to keep it from completing" before we give
the event back to the hardware. Completion processing for that
transaction (and any other "new" ones) will not occur until after
this function returns, so there's no risk it completing early. So
there's no need to take and drop the additional transaction
reference.
Use local variables in the call to gsi_evt_ring_doorbell().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, misc
updates and fallout fixes from recent Florian's code rewritting (from
last pull request):
1) Use new flowi4_l3mdev field in ip_route_me_harder(), from Martin Willi.
2) Avoid unnecessary GC with a timestamp in conncount, from William Tu
and Yifeng Sun.
3) Remove TCP conntrack debugging, from Florian Westphal.
4) Fix compilation warning in ctnetlink, from Florian.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: ctnetlink: fix up for "netfilter: conntrack: remove unconfirmed list"
netfilter: conntrack: remove pr_debug callsites from tcp tracker
netfilter: nf_conncount: reduce unnecessary GC
netfilter: Use l3mdev flow key when re-routing mangled packets
====================
Jakub Kicinski [Fri, 20 May 2022 01:25:55 +0000 (18:25 -0700)]
eth: mtk_ppe: fix up after merge
I missed this in the barrage of GCC 12 warnings. Commit c00dcd670adc
("net: fix dev_fill_forward_path with pppoe + bridge") changed
the pointer into an array.
Geliang Tang [Wed, 18 May 2022 22:04:46 +0000 (15:04 -0700)]
selftests: mptcp: add MP_FAIL reset testcase
Add the multiple subflows test case for MP_FAIL, to test the MP_FAIL
reset case. Use the test_linkfail value to make 1024KB test files.
Invoke reset_with_fail() to use 'iptables' and 'tc action pedit' rules
to produce the bit flips to trigger the checksum failures on ns2eth2.
Add delays on ns2eth1 to make sure more data can translate on ns2eth2.
The check_invert flag is enabled in reset_with_fail(), so this test
prints out the inverted bytes, instead of the file mismatch errors.
Invoke pedit_action_pkts() to get the numbers of the packets edited
by the tc pedit actions, and print this numbers to the output.
Co-developed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau [Wed, 18 May 2022 22:04:45 +0000 (15:04 -0700)]
mptcp: Do not traverse the subflow connection list without lock
The MPTCP socket's conn_list (list of subflows) requires the socket lock
to access. The MP_FAIL timeout code added such an access, where it would
check the list of subflows both in timer context and (later) in workqueue
context where the socket lock is held.
Rather than check the list twice, remove the check in the timeout
handler and only depend on the check in the workqueue. Also remove the
MPTCP_FAIL_NO_RESPONSE flag, since mptcp_mp_fail_no_response() has
insignificant overhead and can be checked on each worker run.
Fixes: f1398993853c ("mptcp: reset subflow when MP_FAIL doesn't respond") Reported-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau [Wed, 18 May 2022 22:04:44 +0000 (15:04 -0700)]
mptcp: Check for orphaned subflow before handling MP_FAIL timer
MP_FAIL timeout (waiting for a peer to respond to an MP_FAIL with
another MP_FAIL) is implemented using the MPTCP socket's sk_timer. That
timer is also used at MPTCP socket close, so it's important to not have
the two timer users interfere with each other.
At MPTCP socket close, all subflows are orphaned before sk_timer is
manipulated. By checking the SOCK_DEAD flag on the subflows, each
subflow can determine if the timer is safe to alter without acquiring
any MPTCP-level lock. This replaces code that was using the
mptcp_data_lock and MPTCP-level socket state checks that did not
correctly protect the timer.
Fixes: f1398993853c ("mptcp: reset subflow when MP_FAIL doesn't respond") Reviewed-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Wed, 18 May 2022 22:04:43 +0000 (15:04 -0700)]
mptcp: stop using the mptcp_has_another_subflow() helper
The mentioned helper requires the msk socket lock, and the
current callers don't own it nor can't acquire it, so the
access is racy.
All the current callers are really checking for infinite mapping
fallback, and the latter condition is explicitly tracked by
the relevant msk variable: we can safely remove the caller usage
- and the caller itself.
The issue is present since MP_FAIL implementation, but the
fix only applies since the infinite fallback support, ence the
somewhat unexpected fixes tag.
Fixes: 441d20d77c62 ("mptcp: track and update contiguous data status") Acked-and-tested-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuchung Cheng [Thu, 19 May 2022 00:34:10 +0000 (17:34 -0700)]
tcp: improve PRR loss recovery
This patch improves TCP PRR loss recovery behavior for a corner
case. Previously during PRR conservation-bound mode, it strictly
sends the amount equals to the amount newly acked or s/acked.
The patch changes s.t. PRR may send additional amount that was banked
previously (e.g. application-limited) in the conservation-bound
mode, similar to the slow-start mode. This unifies and simplifies the
algorithm further and may improve the recovery latency. This change
still follow the general packet conservation design principle and
always keep inflight/cwnd below the slow start threshold set
by the congestion control module.
PRR is described in RFC 6937. We'll include this change in the
latest revision rfc6937-bis as well.
Jakub Kicinski [Wed, 18 May 2022 23:43:46 +0000 (16:43 -0700)]
docs: change the title of networking docs
The current title of our section of the documentation is
Linux Networking Documentation. Since we're describing
a section of Linux Documentation repeating those two
words seems redundant.
Jakub Kicinski [Thu, 19 May 2022 00:43:42 +0000 (17:43 -0700)]
net: wwan: iosm: remove pointless null check
GCC 12 warns:
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c: In function ‘ipc_protocol_dl_td_process’:
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c:406:13: warning: the comparison will always evaluate as ‘true’ for the address of ‘cb’ will never be NULL [-Waddress]
406 | if (!IPC_CB(skb)) {
| ^
Indeed the check seems entirely pointless. Hopefully the other
validation checks will catch if the cb is bad, but it can't be
NULL.
Jakub Kicinski [Fri, 20 May 2022 01:40:56 +0000 (18:40 -0700)]
Merge branch 'lantiq_gswip-two-small-fixes'
Martin Blumenstingl says:
====================
lantiq_gswip: Two small fixes
While updating the Lantiq target in OpenWrt to Linux 5.15 I came across
an FDB related error message. While that still needs to be solved I
found two other small issues on the way.
This series fixes the two minor issues found while revisiting the FDB
code in the lantiq_gswip driver:
- The first patch fixes the start index used in gswip_port_fdb() to
find the entry with the matching bridge. The updated logic is now
consistent with the rest of the driver.
- The second patch fixes a typo in a dev_err() message.
net: dsa: lantiq_gswip: Fix typo in gswip_port_fdb_dump() error print
gswip_port_fdb_dump() reads the MAC bridge entries. The error message
should say "failed to read mac bridge entry". While here, also add the
index to the error print so humans can get to the cause of the problem
easier.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: dsa: lantiq_gswip: Fix start index in gswip_port_fdb()
The first N entries in priv->vlans are reserved for managing ports which
are not part of a bridge. Use priv->hw_info->max_ports to consistently
access per-bridge entries at index 7. Starting at
priv->hw_info->cpu_port (6) is harmless in this case because
priv->vlan[6].bridge is always NULL so the comparison result is always
false (which results in this entry being skipped).
Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ricardo Martinez [Wed, 18 May 2022 19:55:29 +0000 (12:55 -0700)]
net: wwan: t7xx: Fix smatch errors
t7xx_request_irq() error: uninitialized symbol 'ret'.
t7xx_core_hk_handler() error: potentially dereferencing uninitialized 'event'.
If the condition to enter the loop that waits for the handshake event
is false on the first iteration then the uninitialized 'event' will be
dereferenced, fix this by initializing 'event' to NULL.
t7xx_port_proxy_recv_skb() warn: variable dereferenced before check 'skb'.
No need to check skb at t7xx_port_proxy_recv_skb() since we know it
is always called with a valid skb by t7xx_cldma_gpd_rx_from_q().
Jakub Kicinski [Fri, 20 May 2022 01:14:34 +0000 (18:14 -0700)]
Merge branch 'mtk_eth_soc-phylink-updates'
Russell King says:
====================
mtk_eth_soc phylink updates
This series ultimately updates mtk_eth_soc to use phylink_pcs, with some
fixes along the way.
Previous attempts to update this driver (which is now marked as legacy)
have failed due to lack of testing. I am hoping that this time will be
different; Marek can test RGMII modes, but not SGMII. So all that we
know is that this patch series probably doesn't break RGMII.
1) remove unused mac_mode and sgmii flags members from structures.
2) remove unnecessary interpretation of speed when configuring 1000
and 2500 Base-X
3) move configuration of SGMII duplex setting from mac_config() to
link_up()
4) only pass in interface mode to mtk_sgmii_setup_mode_force()
5) move decision about which mtk_sgmii_setup_mode_*() function to call
into mtk_sgmii.c
6) add a fixme comment for RGMII explaning why the call to
mtk_gmac0_rgmii_adjust() is completely wrong - this needs to be
addressed by someone who has the hardware and can test an appropriate
fix. This fixme means that the driver still can't become non-legacy.
7) move gmac setup from mac_config() to mac_finish() - this preserves
the order that we write to the hardware when we eventually convert to
phylink_pcs()
8) move configuration of syscfg0 in SGMII/802.3z mode to mac_finish()
for the same reasons as (7).
9) convert mtk_sgmii.c code structure and the mtk_sgmii structure to
suit conversion to phylink_pcs
10) finally convert to phylink_pcs
As there has been no feedback from mtk_eth_soc maintainers to my RFC
on April 6th, not my reminder on April 11th, so it's now time to merge
this anyway. Mediatek code seems to be submitted to the kernel and
then the maintainers scarper...
====================
net: mtk_eth_soc: partially convert to phylink_pcs
Partially convert mtk_eth_soc to phylink_pcs, moving the configuration,
link up and AN restart over. However, it seems mac_pcs_get_state()
doesn't actually get the state from the PCS, so we can't convert that
over without a better understanding of the hardware.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mtk_eth_soc: convert code structure to suit split PCS support
Provide a mtk_pcs structure which encapsulates everything that the PCS
functions need (the regmap and ana_rgc3 offset), and use this in the
PCS functions. Provide shim functions to convert from the existing
"mtk_sgmii_*" interface to the converted PCS functions.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mtk_eth_soc: move restoration of SYSCFG0 to mac_finish()
The SGMIISYS configuration is performed while ETHSYS_SYSCFG0 is in a
disabled state. In order to preserve this when we switch to phylink_pcs
we need to move the restoration of this register to the mac_finish()
callback.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mtk_eth_soc: move MAC_MCR setting to mac_finish()
Move the setting of the MTK_MAC_MCR register from the end of mac_config
into the phylink mac_finish() method, to keep it as the very last write
that is done during configuration.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mtk_eth_soc: add fixme comment for state->speed use
Add a fixme comment for the last remaining incorrect usage of
state->speed in the mac_config() method, which is strangely in a code
path which is only run when the PHY interface mode changes.
This means if we are in RGMII mode, changes in state->speed will not
cause the INTF_MODE, TRGMII_RCK_CTRL and TRGMII_TCK_CTRL registers to
be set according to the speed, nor will the TRGPLL clock be set to the
correct value.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Phylink does not guarantee that state->speed will be set correctly in
the mac_config() call, so it's a bug that the driver makes use of it.
Moreover, it is making use of it in a function that is only ever called
for 1000BASE-X and 2500BASE-X which operate at a fixed speed which
happens to be the same setting irrespective of the interface mode. We
can simply remove the switch statement and just set the SGMII interface
speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: mtk_eth_soc: add mask and update PCS speed definitions
The PCS speed setting is a two bit field, but it is defined as two
separate bits. Add a bitfield mask for the speed definitions, an
use the FIELD_PREP() macro to define each PCS speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Ober [Tue, 17 May 2022 18:05:39 +0000 (14:05 -0400)]
net: usb: r8152: Add in new Devices that are supported for Mac-Passthru
Lenovo Thunderbolt 4 Dock, and other Lenovo USB Docks are using the
original Realtek USB ethernet Vendor and Product IDs
If the Network device is Realtek verify that it is on a Lenovo USB hub
before enabling the passthru feature
This also adds in the device IDs for the Lenovo USB Dongle and one other
USB-C dock
V2 fix formating of code
V3 remove Generic define for Device ID 0x8153 and change it to use value
V4 rearrange defines and case statement to put them in better order
v5 create helper function to do the testing work as suggested
Oliver Hartkopp contributes a patch for the ISO-TP CAN protocol to
update the validation of address information during bind.
The next patch is by Jakub Kicinski and converts the CAN network
drivers from netif_napi_add() to the netif_napi_add_weight() function.
Another patch by Oliver Hartkopp removes obsolete CAN specific LED
support.
Vincent Mailhol's patch for the mcp251xfd driver fixes a
-Wunaligned-access warning by clang-14.
* tag 'linux-can-next-for-5.19-20220519' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: mcp251xfd: silence clang's -Wunaligned-access warning
can: can-dev: remove obsolete CAN LED support
can: can-dev: move to netif_napi_add_weight()
can: isotp: isotp_bind(): do not validate unused address information
====================
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
This is a false positive because the field is always being accessed
with the relevant put_unaligned_*() function. Adding __packed to the
structure declaration silences the warning.
Oliver Hartkopp [Wed, 18 May 2022 15:45:27 +0000 (17:45 +0200)]
can: can-dev: remove obsolete CAN LED support
Since commit b65273a824407d ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work
now the code can be removed as preparation for a CAN netdevice Kconfig
rework.
Jakub Kicinski [Tue, 17 May 2022 00:23:45 +0000 (17:23 -0700)]
can: can-dev: move to netif_napi_add_weight()
We want to remove the weight argument from the basic version of the
netif_napi_add() call. Move all the callers in drivers/net/can that
pass a custom weight (i.e. not NAPI_POLL_WEIGHT or 64) to the
netif_napi_add_weight() API.
Oliver Hartkopp [Tue, 17 May 2022 14:56:53 +0000 (16:56 +0200)]
can: isotp: isotp_bind(): do not validate unused address information
With commit 528b3b61a553 ("can: isotp: isotp_bind(): return -EINVAL on
incorrect CAN ID formatting") the bind() syscall returns -EINVAL when
the given CAN ID needed to be sanitized. But in the case of an unconfirmed
broadcast mode the rx CAN ID is not needed and may be uninitialized from
the caller - which is ok.
This patch makes sure the result of an inproper CAN ID format is only
provided when the address information is needed.
Jakub Kicinski [Thu, 19 May 2022 20:01:07 +0000 (13:01 -0700)]
Merge tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
Second set of patches for v5.19 and most likely the last one. rtw89
got support for 8852ce devices and mt76 now supports Wireless Ethernet
Dispatch.
Major changes:
cfg80211/mac80211
- support disabling EHT mode
rtw89
- add support for Realtek 8852ce devices
mt76
- Wireless Ethernet Dispatch support for flow offload
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 ipv6 NS offload support
ath11k
- enable keepalive during WoWLAN suspend
- implement remain-on-channel support
* tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (135 commits)
iwlwifi: mei: fix potential NULL-ptr deref
iwlwifi: mei: clear the sap data header before sending
iwlwifi: mvm: remove vif_count
iwlwifi: mvm: always tell the firmware to accept MCAST frames in BSS
iwlwifi: mvm: add OTP info in case of init failure
iwlwifi: mvm: fix assert 1F04 upon reconfig
iwlwifi: fw: init SAR GEO table only if data is present
iwlwifi: mvm: clean up authorized condition
iwlwifi: mvm: use NULL instead of ERR_PTR when parsing wowlan status
iwlwifi: pcie: simplify MSI-X cause mapping
rtw89: pci: only mask out INT indicator register for disable interrupt v1
rtw89: convert rtw89_band to nl80211_band precisely
rtw89: 8852c: update txpwr tables to HALRF_027_00_052
rtw89: cfo: check mac_id to avoid out-of-bounds
rtw89: 8852c: set TX antenna path
rtw89: add ieee80211::sta_rc_update ops
wireless: Fix Makefile to be in alphabetical order
mac80211: refactor freeing the next_beacon
cfg80211: fix kernel-doc for cfg80211_beacon_data
mac80211: minstrel_ht: support ieee80211_rate_status
...
====================
Boris Pismenny [Wed, 18 May 2022 09:27:31 +0000 (12:27 +0300)]
tls: Add opt-in zerocopy mode of sendfile()
TLS device offload copies sendfile data to a bounce buffer before
transmitting. It allows to maintain the valid MAC on TLS records when
the file contents change and a part of TLS record has to be
retransmitted on TCP level.
In many common use cases (like serving static files over HTTPS) the file
contents are not changed on the fly. In many use cases breaking the
connection is totally acceptable if the file is changed during
transmission, because it would be received corrupted in any case.
This commit allows to optimize performance for such use cases to
providing a new optional mode of TLS sendfile(), in which the extra copy
is skipped. Removing this copy improves performance significantly, as
TLS and TCP sendfile perform the same operations, and the only overhead
is TLS header/trailer insertion.
The new mode can only be enabled with the new socket option named
TLS_TX_ZEROCOPY_SENDFILE on per-socket basis. It preserves backwards
compatibility with existing applications that rely on the copying
behavior.
The new mode is safe, meaning that unsolicited modifications of the file
being sent can't break integrity of the kernel. The worst thing that can
happen is sending a corrupted TLS record, which is in any case not
forbidden when using regular TCP sockets.
Sockets other than TLS device offload are not affected by the new socket
option. The actual status of zerocopy sendfile can be queried with
sock_diag.
Performance numbers in a single-core test with 24 HTTPS streams on
nginx, under 100% CPU load:
Andrew Lunn [Wed, 18 May 2022 00:58:40 +0000 (02:58 +0200)]
net: bridge: Clear offload_fwd_mark when passing frame up bridge interface.
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: a962e7cfa4d9 ("bridge: switchdev: Use an helper to clear forward mark") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jonathan Lemon [Tue, 17 May 2022 21:46:00 +0000 (14:46 -0700)]
ptp: ocp: change sysfs attr group handling
In the detach path, the driver calls sysfs_remove_group() for the
groups it believes has been registered. However, if the group was
never previously registered, then this causes a splat.
Instead, compute the groups that should be registered in advance,
and then call sysfs_create_groups(), which registers them all at once.
Update the error handling appropriately.
Fixes: d0527066f191 ("ptp: ocp: Add firmware capability bits for feature gating") Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/r/20220517214600.10606-1-jonathan.lemon@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / kernel.git / log