The upper 32-bit PHC register is not latched when reading the lower
32-bit PHC register. Current code leaves a small window where we may
not read correct higher order bits if the lower order bits are just about
to wrap around.
This patch fixes this by reading higher order bits twice and makes
sure that final value is correctly paired with its lower 32 bits.
Fixes: bd0bd5797b78 ("bnxt_en: Do not read the PTP PHC during chip reset") Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Tue, 12 Jul 2022 02:26:17 +0000 (22:26 -0400)]
bnxt_en: Fix and simplify XDP transmit path
Fix the missing length hint in the TX BD for the XDP transmit path. The
length hint is required on legacy chips.
Also, simplify the code by eliminating the first_buf local variable.
tx_buf contains the same value. The opaque value only needs to be set
on the first BD. Fix this also for correctness.
Fixes: 4841425dc515 ("bnxt: support transmit and free of aggregation buffers") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Tue, 12 Jul 2022 02:26:15 +0000 (22:26 -0400)]
bnxt_en: Fix bnxt_reinit_after_abort() code path
bnxt_reinit_after_abort() is called during ifup when a previous
FW reset sequence has aborted or a previous ifup has failed after
detecting FW reset. In all cases, it is safe to assume that a
previous FW reset has completed and the driver may not have fully
reinitialized.
Prior to this patch, it is assumed that the
FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE flag will always be
set by the firmware in bnxt_hwrm_if_change(). This may not be true if
the driver has already attempted to register with the firmware. The
firmware may not set the RESET_DONE flag again after the driver has
registered, assuming that the driver has seen the flag already.
Fix it to always go through the FW reset initialization path if
the BNXT_STATE_FW_RESET_DET flag is set. This flag is always set
by the driver after successfully going through bnxt_reinit_after_abort().
Fixes: e648c2683d53 ("bnxt_en: attempt to reinitialize after aborted reset") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_en: reclaim max resources if sriov enable fails
If bnxt_sriov_enable() fails after some resources have been reserved
for the VFs, the current code is not unwinding properly and the
reserved resources become unavailable afterwards. Fix it by
properly unwinding with a call to bnxt_hwrm_func_qcaps() to
reset all maximum resources.
Also, add the missing bnxt_ulp_sriov_cfg() call to let the RDMA
driver know to abort.
Fixes: dfe047769e71 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The following patchset contains Netfilter fixes for net:
1) refcount_inc_not_zero() is not semantically equivalent to
atomic_int_not_zero(), from Florian Westphal. My understanding was
that refcount_*() API provides a wrapper to easier debugging of
reference count leaks, however, there are semantic differences
between these two APIs, where refcount_inc_not_zero() needs a barrier.
Reason for this subtle difference to me is unknown.
2) packet logging is not correct for ARP and IP packets, from the
ARP family and netdev/egress respectively. Use skb_network_offset()
to reach the headers accordingly.
3) set element extension length have been growing over time, replace
a BUG_ON by EINVAL which might be triggerable from userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: mptcp: validate userspace PM tests by default
The new script was not listed in the programs to test.
By consequence, some CIs running MPTCP selftests were not validating
these new tests. Note that MPTCP CI was validating it as it executes all
.sh scripts from 'tools/testing/selftests/net/mptcp' directory.
Fixes: 348320406328 ("selftests: mptcp: functional tests for the userspace PM type") Reported-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 8 Jul 2022 23:36:09 +0000 (16:36 -0700)]
mptcp: fix subflow traversal at disconnect time
At disconnect time the MPTCP protocol traverse the subflows
list closing each of them. In some circumstances - MPJ subflow,
passive MPTCP socket, the latter operation can remove the
subflow from the list, invalidating the current iterator.
Address the issue using the safe list traversing helper
variant.
Reported-by: van fantasy <g1042620637@gmail.com> Fixes: 7cc40ad9c3de ("mptcp: full disconnect implementation") Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: replace BUG_ON by element length check
BUG_ON can be triggered from userspace with an element with a large
userdata area. Replace it by length check and return EINVAL instead.
Over time extensions have been growing in size.
Pick a sufficiently old Fixes: tag to propagate this fix.
Fixes: ef5485c9b3ef ("netfilter: nf_tables: variable sized set element keys / data") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Eric Dumazet [Fri, 8 Jul 2022 15:11:53 +0000 (15:11 +0000)]
vlan: fix memory leak in vlan_newlink()
Blamed commit added back a bug I fixed in commit cb1c7e11fb7a
("vlan: fix memory leak in vlan_dev_set_egress_priority")
If a memory allocation fails in vlan_changelink() after other allocations
succeeded, we need to call vlan_dev_free_egress_priority()
to free all allocated memory because after a failed ->newlink()
we do not call any methods like ndo_uninit() or dev->priv_destructor().
In following example, if the allocation for last element 2000:2001 fails,
we need to free eight prior allocations:
ip link add link dummy0 dummy0.100 type vlan id 100 \
egress-qos-map 1:2 2:3 3:4 4:5 5:6 6:7 7:8 8:9 2000:2001
Fixes: 25002154c919 ("vlan: introduce vlan_dev_free_egress_priority") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Xin Long <lucien.xin@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: fix issue of skb segments exceeds descriptor limitation
TCP packets will be dropped if the segments number in the tx skb
exceeds limitation when sending iperf3 traffic with --zerocopy option.
we make the following changes:
Get nr_frags in nfp_nfdk_tx_maybe_close_block instead of passing from
outside because it will be changed after skb_linearize operation.
Fill maximum dma_len in first tx descriptor to make sure the whole
head is included in the first descriptor.
Fixes: 2c359c6702e5 ("nfp: add support for NFDK data path") Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
selftests: forwarding: Install two missing tests
For some distributions (e.g. OpenWrt) we don't want to rely on rsync
to copy the tests to the target as some extra dependencies need to be
installed. The Makefile in tools/testing/selftests/net/forwarding
already installs most of the tests.
This series adds the two missing tests to the list of installed tests.
That way a downstream distribution can build a package using this
Makefile (and add dependencies there as needed).
====================
When using the Makefile from tools/testing/selftests/net/forwarding/
all tests should be installed. Add no_forwarding.sh to the list of
"to be installed tests" where it has been missing so far.
Fixes: c4b992e95d33ab ("selftests: forwarding: add a no_forwarding.sh test") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When using the Makefile from tools/testing/selftests/net/forwarding/
all tests should be installed. Add local_termination.sh to the list of
"to be installed tests" where it has been missing so far.
Fixes: f99ec492911048 ("selftests: forwarding: add a test for local_termination.sh") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We've added 3 non-merge commits during the last 2 day(s) which contain
a total of 7 files changed, 40 insertions(+), 24 deletions(-).
The main changes are:
1) Fix cBPF splat triggered by skb not having a mac header, from Eric Dumazet.
2) Fix spurious packet loss in generic XDP when pushing packets out (note
that native XDP is not affected by the issue), from Johan Almbladh.
3) Fix bpf_dynptr_{read,write}() helper signatures with flag argument before
its set in stone as UAPI, from Joanne Koong.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs
bpf: Make sure mac_header was set before using it
xdp: Fix spurious packet loss in generic XDP TX path
====================
David S. Miller [Fri, 8 Jul 2022 11:10:34 +0000 (12:10 +0100)]
Merge branch 'sysctl-data-races'
Kuniyuki Iwashima says:
====================
sysctl: Fix data-races around ipv4_table.
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
The first half of this series changes some proc handlers used in ipv4_table
to use READ_ONCE() and WRITE_ONCE() internally to fix data-races on the
sysctl side. Then, the second half adds READ_ONCE() to the other readers
of ipv4_table.
Changes:
v2:
* Drop some changes that makes backporting difficult
* First cleanup patch
* Lockless helpers and .proc_handler changes
* Drop the tracing part for .sysctl_mem
* Steve already posted a fix
* Drop int-to-bool change for cipso
* Should be posted to net-next later
* Drop proc_dobool() change
* Can be included in another series
While reading sysctl_fib_sync_mem, it can be changed concurrently.
So, we need to add READ_ONCE() to avoid a data-race.
Fixes: a4600cdec625 ("ipv4: Allow amount of dirty memory from fib resizing to be controllable") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading icmp sysctl variables, they can be changed concurrently.
So, we need to add READ_ONCE() to avoid data-races.
Fixes: 0fcdcc7c3da1 ("icmp: add a global rate limitation") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading cipso sysctl variables, they can be changed concurrently.
So, we need to add READ_ONCE() to avoid data-races.
Fixes: 3bb76b642333 ("[NetLabel]: CIPSOv4 engine") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl: Fix data races in proc_dointvec_jiffies().
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_dointvec_jiffies() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_dointvec_jiffies() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl: Fix data races in proc_doulongvec_minmax().
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_doulongvec_minmax() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_doulongvec_minmax() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl: Fix data races in proc_douintvec_minmax().
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_douintvec_minmax() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_douintvec_minmax() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: 3af54eccec50 ("sysctl: add unsigned int range support") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_dointvec_minmax() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_dointvec_minmax() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_douintvec() to use READ_ONCE() and WRITE_ONCE()
internally to fix data-races on the sysctl side. For now, proc_douintvec()
itself is tolerant to a data-race, but we still need to add annotations on
the other subsystem's side.
Fixes: c28cef52864f ("sysctl: handle error writing UINT_MAX to u32 fields") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_dointvec() to use READ_ONCE() and WRITE_ONCE()
internally to fix data-races on the sysctl side. For now, proc_dointvec()
itself is tolerant to a data-race, but we still need to add annotations on
the other subsystem's side.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sock: tracing: Fix sock_exceed_buf_limit not to dereference stale pointer
The trace event sock_exceed_buf_limit saves the prot->sysctl_mem pointer
and then dereferences it in the TP_printk() portion. This is unsafe as the
TP_printk() portion is executed at the time the buffer is read. That is,
it can be seconds, minutes, days, months, even years later. If the proto
is freed, then this dereference will can also lead to a kernel crash.
Instead, save the sysctl_mem array into the ring buffer and have the
TP_printk() reference that instead. This is the proper and safe way to
read pointers in trace events.
Link: https://lore.kernel.org/all/20220706052130.16368-12-kuniyu@amazon.com/ Cc: stable@vger.kernel.org Fixes: 64c86253719f3 ("core: add tracepoints for queueing skb to rcvbuf") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bpf: Add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs
Commit 26ef2f0c8696 ("bpf: Add bpf_dynptr_read and bpf_dynptr_write")
added the bpf_dynptr_write() and bpf_dynptr_read() APIs.
However, it will be needed for some dynptr types to pass in flags as
well (e.g. when writing to a skb, the user may like to invalidate the
hash or recompute the checksum).
This patch adds a "u64 flags" arg to the bpf_dynptr_read() and
bpf_dynptr_write() APIs before their UAPI signature freezes where
we then cannot change them anymore with a 5.19.x released kernel.
Pavel Skripkin [Wed, 6 Jul 2022 13:28:45 +0000 (16:28 +0300)]
net: ocelot: fix wrong time_after usage
Accidentally noticed, that this driver is the only user of
while (time_after(jiffies...)).
It looks like typo, because likely this while loop will finish after 1st
iteration, because time_after() returns true when 1st argument _is after_
2nd one.
There is one possible problem with this poll loop: the scheduler could put
the thread to sleep, and it does not get woken up for
OCELOT_FDMA_CH_SAFE_TIMEOUT_US. During that time, the hardware has done
its thing, but you exit the while loop and return -ETIMEDOUT.
Fix it by using sane poll API that avoids all problems described above
Fixes: 63f3021bd722 ("net: ocelot: add FDMA support") Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220706132845.27968-1-paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 8 Jul 2022 00:44:45 +0000 (17:44 -0700)]
Merge tag 'mlx5-fixes-2022-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-07-06
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Ring the TX doorbell on DMA errors
net/mlx5e: Fix capability check for updating vnic env counters
net/mlx5e: CT: Use own workqueue instead of mlx5e priv
net/mlx5: Lag, correct get the port select mode str
net/mlx5e: Fix enabling sriov while tc nic rules are offloaded
net/mlx5e: kTLS, Fix build time constant test in RX
net/mlx5e: kTLS, Fix build time constant test in TX
net/mlx5: Lag, decouple FDB selection and shared FDB
net/mlx5: TC, allow offload from uplink to other PF's VF
====================
net: ethernet: ti: am65-cpsw: Fix devlink port register sequence
Renaming interfaces using udevd depends on the interface being registered
before its netdev is registered. Otherwise, udevd reads an empty
phys_port_name value, resulting in the interface not being renamed.
Fix this by registering the interface before registering its netdev
by invoking am65_cpsw_nuss_register_devlink() before invoking
register_netdev() for the interface.
Move the function call to devlink_port_type_eth_set(), invoking it after
register_netdev() is invoked, to ensure that netlink notification for the
port state change is generated after the netdev is completely initialized.
Jon Hunter [Wed, 6 Jul 2022 08:39:13 +0000 (09:39 +0100)]
net: stmmac: dwc-qos: Disable split header for Tegra194
There is a long-standing issue with the Synopsys DWC Ethernet driver
for Tegra194 where random system crashes have been observed [0]. The
problem occurs when the split header feature is enabled in the stmmac
driver. In the bad case, a larger than expected buffer length is
received and causes the calculation of the total buffer length to
overflow. This results in a very large buffer length that causes the
kernel to crash. Why this larger buffer length is received is not clear,
however, the feedback from the NVIDIA design team is that the split
header feature is not supported for Tegra194. Therefore, disable split
header support for Tegra194 to prevent these random crashes from
occurring.
Unlike atomic_inc_not_zero, refcount_inc_not_zero is not a full barrier.
conntrack uses SLAB_TYPESAFE_BY_RCU, i.e. it is possible that a 'newly'
allocated object is still in use on another CPU:
CPU1 CPU2
encounter 'ct' during hlist walk
delete_from_lists
refcount drops to 0
kmem_cache_free(ct);
__nf_conntrack_alloc() // returns same object
refcount_inc_not_zero(ct); /* might fail */
/* If set, ct is public/in the hash table */
test_bit(IPS_CONFIRMED_BIT, &ct->status);
In case CPU1 already set refcount back to 1, refcount_inc_not_zero()
will succeed.
The expected possibilities for a CPU that obtained the object 'ct'
(but no reference so far) are:
1. refcount_inc_not_zero() fails. CPU2 ignores the object and moves to
the next entry in the list. This happens for objects that are about
to be free'd, that have been free'd, or that have been reallocated
by __nf_conntrack_alloc(), but where the refcount has not been
increased back to 1 yet.
2. refcount_inc_not_zero() succeeds. CPU2 checks the CONFIRMED bit
in ct->status. If set, the object is public/in the table.
If not, the object must be skipped; CPU2 calls nf_ct_put() to
un-do the refcount increment and moves to the next object.
Parallel deletion from the hlists is prevented by a
'test_and_set_bit(IPS_DYING_BIT, &ct->status);' check, i.e. only one
cpu will do the unlink, the other one will only drop its reference count.
Because refcount_inc_not_zero is not a full barrier, CPU2 may try to
delete an object that is not on any list:
1. refcount_inc_not_zero() successful (refcount inited to 1 on other CPU)
2. CONFIRMED test also successful (load was reordered or zeroing
of ct->status not yet visible)
3. delete_from_lists unlinks entry not on the hlist, because
IPS_DYING_BIT is 0 (already cleared).
2) is already wrong: CPU2 will handle a partially initited object
that is supposed to be private to CPU1.
Add needed barriers when refcount_inc_not_zero() is successful.
It also inserts a smp_wmb() before the refcount is set to 1 during
allocation.
Because other CPU might still see the object, refcount_set(1)
"resurrects" it, so we need to make sure that other CPUs will also observe
the right content. In particular, the CONFIRMED bit test must only pass
once the object is fully initialised and either in the hash or about to be
inserted (with locks held to delay possible unlink from early_drop or
gc worker).
I did not change flow_offload_alloc(), as far as I can see it should call
refcount_inc(), not refcount_inc_not_zero(): the ct object is attached to
the skb so its refcount should be >= 1 in all cases.
v2: prefer smp_acquire__after_ctrl_dep to smp_rmb (Will Deacon).
v3: keep smp_acquire__after_ctrl_dep close to refcount_inc_not_zero call
add comment in nf_conntrack_netlink, no control dependency there
due to locks.
Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/all/Yr7WTfd6AVTQkLjI@e126311.manchester.arm.com/ Reported-by: Kajetan Puchalski <kajetan.puchalski@arm.com> Diagnosed-by: Will Deacon <will@kernel.org> Fixes: 5d04d48f904f ("netfilter: conntrack: convert to refcount_t api") Signed-off-by: Florian Westphal <fw@strlen.de> Acked-by: Will Deacon <will@kernel.org>
Fixes: f9aefd6b2aa3 ("net: warn if mac header was not set") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220707123900.945305-1-edumazet@google.com
- eth: ibmvnic: properly dispose of all skbs during a failover
Previous releases - always broken:
- bpf:
- fix insufficient bounds propagation from
adjust_scalar_min_max_vals
- clear page contiguity bit when unmapping pool
- netfilter: nft_set_pipapo: release elements in clone from
abort path
- mptcp: netlink: issue MP_PRIO signals from userspace PMs
- can:
- rcar_canfd: fix data transmission failed on R-Car V3U
- gs_usb: gs_usb_open/close(): fix memory leak
Misc:
- add Wenjia as SMC maintainer"
* tag 'net-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
wireguard: Kconfig: select CRYPTO_CHACHA_S390
crypto: s390 - do not depend on CRYPTO_HW for SIMD implementations
wireguard: selftests: use microvm on x86
wireguard: selftests: always call kernel makefile
wireguard: selftests: use virt machine on m68k
wireguard: selftests: set fake real time in init
r8169: fix accessing unset transport header
net: rose: fix UAF bug caused by rose_t0timer_expiry
usbnet: fix memory leak in error case
Revert "tls: rx: move counting TlsDecryptErrors for sync"
mptcp: update MIB_RMSUBFLOW in cmd_sf_destroy
mptcp: fix local endpoint accounting
selftests: mptcp: userspace PM support for MP_PRIO signals
mptcp: netlink: issue MP_PRIO signals from userspace PMs
mptcp: Acquire the subflow socket lock before modifying MP_PRIO flags
mptcp: Avoid acquiring PM lock for subflow priority changes
mptcp: fix locking in mptcp_nl_cmd_sf_destroy()
net/mlx5e: Fix matchall police parameters validation
net/sched: act_police: allow 'continue' action offload
net: lan966x: hardcode the number of external ports
...
Merge tag 'pinctrl-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Tag Intel pin control as supported in MAINTAINERS
- Fix a NULL pointer exception in the Aspeed driver
- Correct some NAND functions in the Sunxi A83T driver
- Use the right offset for some Sunxi pins
- Fix a zero base offset in the Freescale (NXP) i.MX93
- Fix the IRQ support in the STM32 driver
* tag 'pinctrl-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: fix optional IRQ support to gpios
pinctrl: imx: Add the zero base flag for imx93
pinctrl: sunxi: sunxi_pconf_set: use correct offset
pinctrl: sunxi: a83t: Fix NAND function name for some pins
pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
MAINTAINERS: Update Intel pin control to Supported
These are indeed "should not happen" situations, but it turns out recent
changes made the 'task_is_stopped_or_trace()' case trigger (fix for that
exists, is pending more testing), and the BUG_ON() makes it
unnecessarily hard to actually debug for no good reason.
It's been that way for a long time, but let's make it clear: BUG_ON() is
not good for debugging, and should never be used in situations where you
could just say "this shouldn't happen, but we can continue".
Use WARN_ON_ONCE() instead to make sure it gets logged, and then just
continue running. Instead of making the system basically unusuable
because you crashed the machine while potentially holding some very core
locks (eg this function is commonly called while holding 'tasklist_lock'
for writing).
Jakub Kicinski [Thu, 7 Jul 2022 03:04:09 +0000 (20:04 -0700)]
Merge branch 'wireguard-patches-for-5-19-rc6'
Jason A. Donenfeld says:
====================
wireguard patches for 5.19-rc6
1) A few small fixups to the selftests, per usual. Of particular note is
a fix for a test flake that occurred on especially fast systems that
boot in less than a second.
2) An addition during this cycle of some s390 crypto interacted with the
way wireguard selects dependencies, resulting in linker errors
reported by the kernel test robot. So Vladis sent in a patch for
that, which also required a small preparatory fix moving some Kconfig
symbols around.
====================
Select the new implementation of CHACHA20 for S390 when available.
It is faster than the generic software implementation, but also prevents
some linker errors in certain situations.
crypto: s390 - do not depend on CRYPTO_HW for SIMD implementations
Various accelerated software implementation Kconfig values for S390 were
mistakenly placed into drivers/crypto/Kconfig, even though they're
mainly just SIMD code and live in arch/s390/crypto/ like usual. This
gives them the very unusual dependency on CRYPTO_HW, which leads to
problems elsewhere.
This patch fixes the issue by moving the Kconfig values for non-hardware
drivers into the usual place in crypto/Kconfig.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These selftests are used for much more extensive changes than just the
wireguard source files. So always call the kernel's build file, which
will do something or nothing after checking the whole tree, per usual.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all platforms have an RTC, and rather than trying to force one into
each, it's much easier to just set a fixed time. This is necessary
because WireGuard's latest handshakes parameter is returned in wallclock
time, and if the system time isn't set, and the system is really fast,
then this returns 0, which trips the test.
Turning this on requires setting CONFIG_COMPAT_32BIT_TIME=y, as musl
doesn't support settimeofday without it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
f588aa3f3718 ("net: warn if transport header was not set") added
a check that triggers a warning in r8169, see [0].
The commit referenced in the Fixes tag refers to the change from
which the patch applies cleanly, there's nothing wrong with this
commit. It seems the actual issue (not bug, because the warning
is harmless here) was introduced with e50413acc35f
("r8169: use Giant Send").
net: rose: fix UAF bug caused by rose_t0timer_expiry
There are UAF bugs caused by rose_t0timer_expiry(). The
root cause is that del_timer() could not stop the timer
handler that is running and there is no synchronization.
One of the race conditions is shown below:
The rose_neigh is deallocated in position [1] and use in
position [2].
The crash trace triggered by POC is like below:
BUG: KASAN: use-after-free in expire_timers+0x144/0x320
Write of size 8 at addr ffff888009b19658 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? expire_timers+0x144/0x320
kasan_report+0xed/0x120
? expire_timers+0x144/0x320
expire_timers+0x144/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
...
This patch changes rose_stop_ftimer() and rose_stop_t0timer()
in rose_remove_neigh() to del_timer_sync() in order that the
timer handler could be finished before the resources such as
rose_neigh and so on are deallocated. As a result, the UAF
bugs could be mitigated.
TX doorbells may be postponed, because sometimes the driver knows that
another packet follows (for example, when xmit_more is true, or when a
MPWQE session is closed before transmitting a packet).
However, the DMA mapping may fail for the next packet, in which case a
new WQE is not posted, the doorbell isn't updated either, and the
transmission of the previous packet will be delayed indefinitely.
This commit fixes the described rare error flow by posting a NOP and
ringing the doorbell on errors to flush all the previous packets. The
MPWQE session is closed before that. DMA mapping in the MPWQE flow is
moved to the beginning of mlx5e_sq_xmit_mpwqe, because empty sessions
are not allowed. Stop room always has enough space for a NOP, because
the actual TX WQE is not posted.
Gal Pressman [Mon, 27 Jun 2022 12:05:53 +0000 (15:05 +0300)]
net/mlx5e: Fix capability check for updating vnic env counters
The existing capability check for vnic env counters only checks for
receive steering discards, although we need the counters update for the
exposed internal queue oob counter as well. This could result in the
latter counter not being updated correctly when the receive steering
discards counter is not supported.
Fix that by checking whether any counter is supported instead of only
the steering counter capability.
Fixes: 67c2872e1db0 ("net/mlx5e: Add device out of buffer counter") Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Roi Dayan [Tue, 21 Jun 2022 07:43:55 +0000 (10:43 +0300)]
net/mlx5e: CT: Use own workqueue instead of mlx5e priv
Allocate a ct priv workqueue instead of using mlx5e priv one
so flushing will only be of related CT entries.
Also move flushing of the workqueue before rhashtable destroy
otherwise entries won't be valid.
Fixes: 7214869491ee ("net/mlx5e: CT: Fix queued up restore put() executing after relevant ft release") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Liu, Changcheng [Fri, 27 May 2022 08:49:14 +0000 (16:49 +0800)]
net/mlx5: Lag, correct get the port select mode str
mode & mode_flags is updated at the end of mlx5_activate_lag which
may not reflect the actual mode as shown in below logic:
mlx5_activate_lag(struct mlx5_lag *ldev,
|-- unsigned long flags = 0;
|-- err = mlx5_lag_set_flags(ldev, mode, tracker, shared_fdb, &flags);
|-- err = mlx5_create_lag(ldev, tracker, mode, flags);
|-- mlx5_get_str_port_sel_mode(ldev);
|-- ldev->mode = mode;
|-- ldev->mode_flags = flags;
Use mode & flag as parameters to get port select mode info.
Fixes: 94d7020b1395 ("net/mlx5: Support multiport eswitch mode") Signed-off-by: Liu, Changcheng <jerrliu@nvidia.com> Reviewed-by: Eli Cohen <elic@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Paul Blakey [Wed, 22 Jun 2022 10:11:18 +0000 (13:11 +0300)]
net/mlx5e: Fix enabling sriov while tc nic rules are offloaded
There is a total of four 4M entries flow tables. In sriov disabled
mode, ct, ct_nat and post_act take three of them. When adding the
first tc nic rule in this mode, it will take another 4M table
for the tc <chain,prio> table. If user then enables sriov, the legacy
flow table tries to take another 4M and fails, and so enablement fails.
To fix that, have legacy fdb take the next available maximum
size from the fs ft pool.
Fixes: d11f514c8884 ("net/mlx5: Move chains ft pool to be used by all firmware steering") Signed-off-by: Paul Blakey <paulb@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Mark Bloch [Tue, 24 May 2022 09:08:10 +0000 (12:08 +0300)]
net/mlx5: Lag, decouple FDB selection and shared FDB
Multiport eswitch is required to use native FDB selection instead of
affinity, This was achieved by passing the shared_fdb flag down
the HW lag creation path. While it did accomplish the goal of setting
FDB selection mode to native, it had the side effect of also
creating a shared FDB configuration.
This created a few issues:
- TC rules are inserted into a non active FDB, which means traffic isn't
offloaded as all traffic will reach only a single FDB.
- All wire traffic is treated as if a single physical port received it; while
this is true for a bond configuration, this shouldn't be the case for
multiport eswitch.
Create a new flag MLX5_LAG_MODE_FLAG_FDB_SEL_MODE_NATIVE
to indicate what FDB selection mode should be used.
Fixes: 94d7020b1395 ("net/mlx5: Support multiport eswitch mode") Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Eli Cohen <elic@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Merge tag 'for-linus' of https://github.com/openrisc/linux
Pull OpenRISC fixes from Stafford Horne:
"Fixups for OpenRISC found during recent testing:
- An OpenRISC irqchip fix to stop acking level interrupts which was
causing issues on SMP platforms
- A comment typo fix in our unwinder code"
* tag 'for-linus' of https://github.com/openrisc/linux:
openrisc: unwinder: Fix grammar issue in comment
irqchip: or1k-pic: Undefine mask_ack for level triggered hardware
Merge tag 'sound-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became largish as it includes the pending ASoC fixes.
Almost all changes are device-specific small fixes, while many of them
are coverage for mixer issues that were detected by selftest. In
addition, usual suspects for HD/USB-audio are there"
* tag 'sound-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (43 commits)
ALSA: cs46xx: Fix missing snd_card_free() call at probe error
ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)
ALSA: usb-audio: Add quirk for Fiero SC-01
ALSA: hda/realtek: Add quirk for Clevo L140PU
ALSA: usb-audio: Add quirks for MacroSilicon MS2100/MS2106 devices
ASoC: madera: Fix event generation for rate controls
ASoC: madera: Fix event generation for OUT1 demux
ASoC: cs47l15: Fix event generation for low power mux control
ASoC: cs35l41: Add ASP TX3/4 source to register patch
ASoC: dapm: Initialise kcontrol data for mux/demux controls
ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
ASoC: cs35l41: Correct some control names
ASoC: wm5110: Fix DRE control
ASoC: wm_adsp: Fix event for preloader
MAINTAINERS: update ASoC Qualcomm maintainer email-id
ASoC: rockchip: i2s: switch BCLK to GPIO
ASoC: SOF: Intel: disable IMR boot when resuming from ACPI S4 and S5 states
ASoC: SOF: pm: add definitions for S4 and S5 states
ASoC: SOF: pm: add explicit behavior for ACPI S1 and S2
ASoC: SOF: Intel: hda: Fix compressed stream position tracking
...
Johan Almbladh [Tue, 5 Jul 2022 08:23:45 +0000 (10:23 +0200)]
xdp: Fix spurious packet loss in generic XDP TX path
The byte queue limits (BQL) mechanism is intended to move queuing from
the driver to the network stack in order to reduce latency caused by
excessive queuing in hardware. However, when transmitting or redirecting
a packet using generic XDP, the qdisc layer is bypassed and there are no
additional queues. Since netif_xmit_stopped() also takes BQL limits into
account, but without having any alternative queuing, packets are
silently dropped.
This patch modifies the drop condition to only consider cases when the
driver itself cannot accept any more packets. This is analogous to the
condition in __dev_direct_xmit(). Dropped packets are also counted on
the device.
Bypassing the qdisc layer in the generic XDP TX path means that XDP
packets are able to starve other packets going through a qdisc, and
DDOS attacks will be more effective. In-driver-XDP use dedicated TX
queues, so they do not have this starvation issue.
Gal Pressman [Tue, 5 Jul 2022 11:08:37 +0000 (14:08 +0300)]
Revert "tls: rx: move counting TlsDecryptErrors for sync"
This reverts commit 30ead968b9220bf175b3568d52c501b10f95d10f.
When using TLS device offload and coming from tls_device_reencrypt()
flow, -EBADMSG error in tls_do_decryption() should not be counted
towards the TLSTlsDecryptError counter.
Move the counter increase back to the decrypt_internal() call site in
decrypt_skb_update().
This also fixes an issue where:
if (n_sgin < 1)
return -EBADMSG;
Errors in decrypt_internal() were not counted after the cited patch.
Fixes: 30ead968b922 ("tls: rx: move counting TlsDecryptErrors for sync") Cc: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Jul 2022 11:50:27 +0000 (12:50 +0100)]
Merge branch 'mptcp-path-manager-fixes'
Mat Martineau says:
====================
mptcp: Path manager fixes for 5.19
The MPTCP userspace path manager is new in 5.19, and these patches fix
some issues in that new code.
Patches 1-3 fix path manager locking issues.
Patches 4 and 5 allow userspace path managers to change priority of
established subflows using the existing MPTCP_PM_CMD_SET_FLAGS generic
netlink command. Includes corresponding self test update.
Patches 6 and 7 fix accounting of available endpoint IDs and the
MPTCP_MIB_RMSUBFLOW counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 5 Jul 2022 21:32:16 +0000 (14:32 -0700)]
mptcp: fix local endpoint accounting
In mptcp_pm_nl_rm_addr_or_subflow() we always mark as available
the id corresponding to the just removed address.
The used bitmap actually tracks only the local IDs: we must
restrict the operation when a (local) subflow is removed.
Fixes: 02fcb7437966 ("mptcp: do not block subflows creation on errors") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: mptcp: userspace PM support for MP_PRIO signals
This change updates the testing sample (pm_nl_ctl) to exercise
the updated MPTCP_PM_CMD_SET_FLAGS command for userspace PMs to
issue MP_PRIO signals over the selected subflow.
E.g. ./pm_nl_ctl set 10.0.1.2 port 47234 flags backup token 823274047 rip 10.0.1.1 rport 50003
userspace_pm.sh has a new selftest that invokes this command.
Fixes: 348320406328 ("selftests: mptcp: functional tests for the userspace PM type") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Kishen Maloor <kishen.maloor@intel.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp: netlink: issue MP_PRIO signals from userspace PMs
This change updates MPTCP_PM_CMD_SET_FLAGS to allow userspace PMs
to issue MP_PRIO signals over a specific subflow selected by
the connection token, local and remote address+port.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/286 Fixes: 33ecd4cecca3 ("mptcp: netlink: allow userspace-driven subflow establishment") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Kishen Maloor <kishen.maloor@intel.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau [Tue, 5 Jul 2022 21:32:13 +0000 (14:32 -0700)]
mptcp: Acquire the subflow socket lock before modifying MP_PRIO flags
When setting up a subflow's flags for sending MP_PRIO MPTCP options, the
subflow socket lock was not held while reading and modifying several
struct members that are also read and modified in mptcp_write_options().
Acquire the subflow socket lock earlier and send the MP_PRIO ACK with
that lock already acquired. Add a new variant of the
mptcp_subflow_send_ack() helper to use with the subflow lock held.
Fixes: 641df33b6ffc ("mptcp: add the outgoing MP_PRIO support") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau [Tue, 5 Jul 2022 21:32:12 +0000 (14:32 -0700)]
mptcp: Avoid acquiring PM lock for subflow priority changes
The in-kernel path manager code for changing subflow flags acquired both
the msk socket lock and the PM lock when possibly changing the "backup"
and "fullmesh" flags. mptcp_pm_nl_mp_prio_send_ack() does not access
anything protected by the PM lock, and it must release and reacquire
the PM lock.
By pushing the PM lock to where it is needed in mptcp_pm_nl_fullmesh(),
the lock is only acquired when the fullmesh flag is changed and the
backup flag code no longer has to release and reacquire the PM lock. The
change in locking context requires the MIB update to be modified - move
that to a better location instead.
This change also makes it possible to call
mptcp_pm_nl_mp_prio_send_ack() for the userspace PM commands without
manipulating the in-kernel PM lock.
Fixes: 6a6ac942f8f8 ("mptcp: add set_flags command in PM netlink") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 5 Jul 2022 21:32:11 +0000 (14:32 -0700)]
mptcp: fix locking in mptcp_nl_cmd_sf_destroy()
The user-space PM subflow removal path uses a couple of helpers
that must be called under the msk socket lock and the current
code lacks such requirement.
Change the existing lock scope so that the relevant code is under
its protection.
Fixes: 33ecd4cecca3 ("mptcp: netlink: allow userspace-driven subflow establishment") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/287 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
TC act_police with 'continue' action had been supported by mlx5 matchall
classifier offload implementation for some time. However, 'continue' was
assumed implicitly and recently got broken in multiple places. Fix it in
both TC hardware offload validation code and mlx5 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Referenced commit prepared the code for upcoming extension that allows mlx5
to offload police action attached to flower classifier. However, with
regard to existing matchall classifier offload validation should be
reversed as FLOW_ACTION_CONTINUE is the only supported notexceed police
action type. Fix the problem by allowing FLOW_ACTION_CONTINUE for police
action and extend scan_tc_matchall_fdb_actions() to only allow such actions
with matchall classifier.
Fixes: d7826daaf80f ("flow_offload: reject offload for all drivers with invalid police parameters") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Acked-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading police with action TC_ACT_UNSPEC was erroneously disabled even
though it was supported by mlx5 matchall offload implementation, which
didn't verify the action type but instead assumed that any single police
action attached to matchall classifier is a 'continue' action. Lack of
action type check made it non-obvious what mlx5 matchall implementation
actually supports and caused implementers and reviewers of referenced
commits to disallow it as a part of improved validation code.
Fixes: e261130e9075 ("net: flow_offload: add tc police action parameters") Fixes: 7d8f08e22631 ("net/sched: act_police: Add extack messages for offload failure") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle [Mon, 4 Jul 2022 15:36:54 +0000 (17:36 +0200)]
net: lan966x: hardcode the number of external ports
Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself. The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.
It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.
Fixes: 74253577d2c1 ("net: lan966x: add the basic lan966x driver") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220704153654.1762116-1-michael@walle.cc Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 5 Jul 2022 21:42:09 +0000 (14:42 -0700)]
Merge tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix deadlock when powering on.
* tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: core: Fix deadlock on hci_power_on_sync.
====================
Bluetooth: core: Fix deadlock on hci_power_on_sync.
`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.
But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.
NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.
As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.
[1]: commit 32f0ee060017 ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
Fixes: 32f0ee060017 ("Bluetooth: core: Fix missing power_on work cancel on HCI close") Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com> Reported-by: Max Krummenacher <max.krummenacher@toradex.com> Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Merge tag 'xsa-5.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen security fixes from Juergen Gross:
- XSA-403 (4 patches for blkfront and netfront drivers):
Linux Block and Network PV device frontends don't zero memory regions
before sharing them with the backend (CVE-2022-26365,
CVE-2022-33740). Additionally the granularity of the grant table
doesn't allow sharing less than a 4K page, leading to unrelated data
residing in the same 4K page as data shared with a backend being
accessible by such backend (CVE-2022-33741, CVE-2022-33742).
- XSA-405 (1 patch for netfront driver, only 5.10 and newer):
While adding logic to support XDP (eXpress Data Path), a code label
was moved in a way allowing for SKBs having references (pointers)
retained for further processing to nevertheless be freed.
- XSA-406 (1 patch for Arm specific dom0 code):
When mapping pages of guests on Arm, dom0 is using an rbtree to keep
track of the foreign mappings.
Updating of that rbtree is not always done completely with the
related lock held, resulting in a small race window, which can be
used by unprivileged guests via PV devices to cause inconsistencies
of the rbtree. These inconsistencies can lead to Denial of Service
(DoS) of dom0, e.g. by causing crashes or the inability to perform
further mappings of other guests' memory pages.
* tag 'xsa-5.19-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/arm: Fix race in RB-tree based P2M accounting
xen-netfront: restore __skb_queue_tail() positioning in xennet_get_responses()
xen/blkfront: force data bouncing when backend is untrusted
xen/netfront: force data bouncing when backend is untrusted
xen/netfront: fix leaking data in shared pages
xen/blkfront: fix leaking data in shared pages
ALSA: cs46xx: Fix missing snd_card_free() call at probe error
The previous cleanup with devres may lead to the incorrect release
orders at the probe error handling due to the devres's nature. Until
we register the card, snd_card_free() has to be called at first for
releasing the stuff properly when the driver tries to manage and
release the stuff via card->private_free().
This patch fixes it by calling snd_card_free() manually on the error
from the probe callback.
====================
Fix bridge_vlan_aware.sh and bridge_vlan_unaware.sh with IFF_UNICAST_FLT
Make sure that h1 and h2 don't drop packets with a random MAC DA, which
otherwise confuses these selftests. Also, fix an incorrect error message
found during those failures.
====================
Vladimir Oltean [Sun, 3 Jul 2022 07:36:26 +0000 (10:36 +0300)]
selftests: forwarding: fix error message in learning_test
When packets are not received, they aren't received on $host1_if, so the
message talking about the second host not receiving them is incorrect.
Fix it.
Fixes: fa242965a64a ("selftests: forwarding: Add a test for FDB learning") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean [Sun, 3 Jul 2022 07:36:25 +0000 (10:36 +0300)]
selftests: forwarding: fix learning_test when h1 supports IFF_UNICAST_FLT
The first host interface has by default no interest in receiving packets
MAC DA de:ad:be:ef:13:37, so it might drop them before they hit the tc
filter and this might confuse the selftest.
Enable promiscuous mode such that the filter properly counts received
packets.
Fixes: fa242965a64a ("selftests: forwarding: Add a test for FDB learning") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Vladimir Oltean [Sun, 3 Jul 2022 07:36:24 +0000 (10:36 +0300)]
selftests: forwarding: fix flood_unicast_test when h2 supports IFF_UNICAST_FLT
As mentioned in the blamed commit, flood_unicast_test() works by
checking the match count on a tc filter placed on the receiving
interface.
But the second host interface (host2_if) has no interest in receiving a
packet with MAC DA de:ad:be:ef:13:37, so its RX filter drops it even
before the ingress tc filter gets to be executed. So we will incorrectly
get the message "Packet was not flooded when should", when in fact, the
packet was flooded as expected but dropped due to an unrelated reason,
at some other layer on the receiving side.
Force h2 to accept this packet by temporarily placing it in promiscuous
mode. Alternatively we could either deliver to its MAC address or use
tcpdump_start, but this has the fewest complications.
This fixes the "flooding" test from bridge_vlan_aware.sh and
bridge_vlan_unaware.sh, which calls flood_test from the lib.
Fixes: fa2f5cb33e8e ("selftests: forwarding: Add a test for flooded traffic") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Tue, 5 Jul 2022 03:21:01 +0000 (20:21 -0700)]
Merge tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2022-07-04
The 1st patch is by Oliver Hartkopp, targets the BCM CAN protocol and
converts a costly synchronize_rcu() to call_rcu() to fix a performance
regression.
Srinivas Neeli's patch for the xilinx_can driver drops the brp limit
down to 1, as only the pre-production silicon have an issue with a brp
of 1.
The next patch is by Duy Nguyen and fixes the data transmission on
R-Car V3U SoCs in the rcar_canfd driver.
Rhett Aultman's patch fixes a DMA memory leak in the gs_usb driver.
Liang He's patch removes an extra of_node_get() in the grcan driver.
The next 2 patches are by me, target the m_can driver and fix the
timestamp handling used for peripheral devices like the tcan4x5x.
Jimmy Assarsson contributes 3 patches for the kvaser_usb driver and
fixes CAN clock and bit timing related issues.
The remaining 5 patches target the mcp251xfd driver. Thomas Kopp
contributes 2 patches to improve the workaround for broken CRC when
reading the TBC register. 3 patches by me add a missing
hrtimer_cancel() during the ndo_stop() callback, and fix the reading
of the Device ID register.
* tag 'linux-can-fixes-for-5.19-20220704' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix endianness conversion
can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
can: mcp251xfd: mcp251xfd_stop(): add missing hrtimer_cancel()
can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
can: kvaser_usb: kvaser_usb_leaf: fix bittiming limits
can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression
can: kvaser_usb: replace run-time checks with struct kvaser_usb_driver_info
can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
can: m_can: m_can_chip_config(): actually enable internal timestamping
can: grcan: grcan_probe(): remove extra of_node_get()
can: gs_usb: gs_usb_open/close(): fix memory leak
can: rcar_canfd: Fix data transmission failed on R-Car V3U
Revert "can: xilinx_can: Limit CANFD brp to 2"
can: bcm: use call_rcu() instead of costly synchronize_rcu()
====================
Merge tag 'stm32-dt-for-v5.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.19, round 2
Highlights:
-----------
-Fixes STM32MP15:
- Add missing usbh clock and fix clk order for usbh to avoid PLL
issue.
- Fix SCMI version: use scmi regulator and update missing SCMI
clocks to be able to correcly boot.
* tag 'stm32-dt-for-v5.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
ARM: dts: stm32: delete fixed clock node on STM32MP15-SCMI
ARM: dts: stm32: DSI should use LSE SCMI clock on DK1/ED1 STM32 board
ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
ARM: dts: stm32: fix pwr regulators references to use scmi
Bill Wendling [Mon, 21 Mar 2022 17:49:12 +0000 (10:49 -0700)]
soc: qcom: smem: use correct format characters
When compiling with -Wformat, clang emits the following warnings:
drivers/soc/qcom/smem.c:847:41: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "bad host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
drivers/soc/qcom/smem.c:852:47: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "duplicate host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct one and change type of
remote_host to "u16" to match with other types.
Merge tag 'asoc-fix-v5.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.19
A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.
Egor Vorontsov [Mon, 27 Jun 2022 10:00:34 +0000 (13:00 +0300)]
ALSA: usb-audio: Add quirk for Fiero SC-01
Fiero SC-01 is a USB sound card with two mono inputs and a single
stereo output. The inputs are composed into a single stereo stream.
The device uses a vendor-provided driver on Windows and does not work
at all without it. The driver mostly provides ASIO functionality, but
also alters the way the sound card is queried for sample rates and
clocks.
ALSA queries those failing with an EPIPE (same as Windows 10 does).
Presumably, the vendor-provided driver does not query it at all, simply
matching by VID:PID. Thus, I consider this a buggy firmware and adhere
to a set of fixed endpoint quirks instead.
The soundcard has an internal clock. Implicit feedback mode is required
for the playback.
I have updated my device to v1.1.0 from a Windows 10 VM using a vendor-
provided binary prior to the development, hoping for it to just begin
working. The device provides no obvious way to downgrade the firmware,
and regardless, there's no binary available for v1.0.0 anyway.
Thus, I will be getting another unit to extend the patch with support
for that. Expected to be a simple copy-paste of the existing one,
though.
There were no previous reports of that device in context of Linux
anywhere. Other issues have been reported though, but that's out of the
scope.
John Veness [Fri, 24 Jun 2022 14:07:57 +0000 (15:07 +0100)]
ALSA: usb-audio: Add quirks for MacroSilicon MS2100/MS2106 devices
Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
In mcp251xfd_register_get_dev_id() the device ID register is read with
handcrafted SPI transfers. As all registers, this register is in
little endian. Further it is not naturally aligned in struct
mcp251xfd_map_buf_nocrc::data. However after the transfer the register
content is converted from big endian to CPU endianness not taking care
of being unaligned.
Fix the conversion by converting from little endian to CPU endianness
taking the unaligned source into account.
Side note: So far the register content is 0x0 on all mcp251xfd
compatible chips, and is only used for an informative printk.
can: mcp251xfd: mcp251xfd_register_get_dev_id(): use correct length to read dev_id
The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.
Fix the length of the SPI transfer to read the device ID register
only.
In commit 2cebcedc45bf ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.
Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().
Thomas Kopp [Tue, 21 Dec 2021 22:24:52 +0000 (22:24 +0000)]
can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit c9c84f308944 ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.
Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com Fixes: c9c84f308944 ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") Cc: stable@vger.kernel.org Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Thomas Kopp [Tue, 21 Dec 2021 22:24:52 +0000 (22:24 +0000)]
can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit c9c84f308944 ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.
Update check on 1st data byte and workaround description accordingly.
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com Fixes: c9c84f308944 ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") Cc: stable@vger.kernel.org Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com> Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
projects / kernel.git / log