Sergei Shtylyov [Sun, 13 Mar 2011 20:06:59 +0000 (20:06 +0000)]
davinci: DM644x EVM: register MUSB device earlier
The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 1e963755c02ceaadab7b2aff9a1fe75d647dc290 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code. Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Felipe Balbi <balbi@ti.com> Tested-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port
device. It has a built-in programmable execution engine that can be programmed
to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch adds a driver for this controller device. The driver does not
expose a user-land interface. Protocol drivers built on top of this layer are
expected to remain in-kernel.
Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Rabin Vincent [Thu, 10 Feb 2011 06:15:58 +0000 (11:45 +0530)]
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 15 Feb 2011 14:01:35 +0000 (15:01 +0100)]
mach-ux500: basic HREFv60 support v2
The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.
Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.
Bibek Basu [Tue, 15 Feb 2011 09:46:59 +0000 (10:46 +0100)]
mach-ux500: add hrefv60 GPIO pins
This will centralize all GPIO pin muxing for the different boards
in the MOP500 family to a single file. It also kills off the
deprecated support for the ED (Early Drop) ASIC, this should
never be spotted in the open and ST-Ericsson have internally
deprecated this hardware.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Rebasing and kill old ASIC support] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 16 Feb 2011 09:37:52 +0000 (10:37 +0100)]
plat-nomadik: fix compilation warning
The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.
Cc: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rabin Vincent [Thu, 10 Feb 2011 03:59:53 +0000 (09:29 +0530)]
plat-nomadik: get rid of unused GPIO PM code
The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rikard Olsson [Mon, 3 Jan 2011 13:30:41 +0000 (14:30 +0100)]
plat-nomadik: change sleep/wakeup setting in GPIO SLPM register
This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Rabin Vincent [Mon, 13 Dec 2010 06:32:40 +0000 (12:02 +0530)]
plat-nomadik: implement safe switch sequence for Alt-C
Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.
This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jonas Aaberg [Wed, 13 Oct 2010 11:14:17 +0000 (13:14 +0200)]
plat-nomadik: pull-up/down settings for GPIO resume
Suspend/resume didn't take care of pull-up and pull-down
settings and writing back the DAT register at resume can
change pull up/down settings, depending on pin input value.
Output values are now also restored.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rabin Vincent [Thu, 14 Oct 2010 05:08:03 +0000 (10:38 +0530)]
plat-nomadik: support secondary GPIO interrupts
When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 14 Oct 2010 11:57:59 +0000 (13:57 +0200)]
mach-ux500: config Ux500 PL011 PL022 PL180 for DMA
This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.
Signed-off-by: Per Forlin <per.forlin@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 13 Aug 2010 09:31:59 +0000 (11:31 +0200)]
mach-u300: config U300 PL180 PL011 PL022 for DMA
This will configure the platform data for the PL180, PL011 and
PL022 PrimeCells found in the U300 to use DMA with the generic
PrimeCell DMA engine for COH 901 318.
Linus Walleij [Wed, 2 Feb 2011 13:41:19 +0000 (14:41 +0100)]
mach-u300: use mmci driver for GPIO card detect
The mmci driver can handle a GPIO pin for card detect, using
IRQs and all just fine, so switch to using that. Delete the
old bogus input device hack, if userspace need to detect
MMC cards it should use udev like everyone else.
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
configurations
MUSB driver has been updated to separate out BSP layer
from its generic parts, as separate driver. This patch
configures the clock with the new platform driver name.
USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Linus Walleij [Thu, 2 Dec 2010 16:10:14 +0000 (17:10 +0100)]
mach-ux500: add a few AB8500 regulator consumers v3
Try to make the regulators a little bit more useful by adding some
of the most basic consumers we're going to have in the end.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Rabin Vincent <rabin@rab.in> Cc: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com> Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Subhasish Ghosh [Mon, 7 Mar 2011 14:06:57 +0000 (14:06 +0000)]
davinci: macro rename DA8XX_LPSC0_DMAX to DA8XX_LPSC0_PRUSS.
DMAX is an internal name for the module which is
known as PRUSS in TI public documentation. This patch just
gets the code in sync with TI documentation.
Signed-off-by: Subhasish Ghosh <subhasish@mistralsolutions.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Sergei Shtylyov [Fri, 25 Feb 2011 06:56:36 +0000 (12:26 +0530)]
davinci: DA850 EVM: kill useless variable
Commit e89cb6809a06e15b62afbe49e1afaacd195aa577 (davinci: DA850/OMAP-L138 EVM
expander setup and UI card detection) introduced a useless variable: it's
always set to 1 before it's checked in da850_evm_setup_nor_nand()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Sekhar Nori [Thu, 24 Feb 2011 05:23:27 +0000 (10:53 +0530)]
davinci: add spi devices support for da830/omap-l137/am17x evm
This patch adds the on-board SPI flash device to the
DA830/OMAP-L137/AM17x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da830evm_spi0_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da830evm_init_spi0 to devices-da8xx.c] Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Sekhar Nori [Thu, 24 Feb 2011 05:09:27 +0000 (10:39 +0530)]
davinci: add spi devices support for da850/omap-l138/am18x evm
This patch adds the on-board SPI flash device to the
DA850/OMAP-L138/AM18x EVM. It also registers the SPI flash
device to the MTD subsystem.
Based on SPI flash device support for MityDSP-L138F platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[michael.williamson@criticallink.com: moved da850_evm_spi1_pdata to devices-da8xx.c]
[michael.williamson@criticallink.com: moved da850evm_init_spi1 to devices-da8xx.c] Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
davinci: add spi devices support for MityDSP-L138/MityARM-1808 platform
This patch adds support for accessing the on board SPI NOR FLASH
device for MityDSP-L138 and MityARM-1808 SoMs.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
davinci: da8xx: add spi resources and registration routine
Add IO resource structures, platform data, and a registration
routine in order to support spi device on DA850/OMAP-L138/AM18x
and DA830/OMAP-L137/AM17x platforms.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
The spi driver name called out for the da830 spi clock list is not correct,
fix it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
davinci: da8xx: clean up magic numbers in devices-da8xx.c
Extract magic numbers from DMA resource initializers to #defines.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
The DA830_edma_ch enum set is not used. Remove it.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
Oskar Schirmer [Thu, 17 Feb 2011 15:43:02 +0000 (16:43 +0100)]
arm: tcc8k: Fix bus clock calculation
There are two dividers used to derive bus clock from system clock:
system clock is divided by SCKDIV+1, then by BCKDIV+1. SCKDIV divider
has been ignored up to now, which is no problem as long as it is 0.
Take SCKDIV into account for bus clock calculation.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de> Cc: bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Oskar Schirmer [Thu, 17 Feb 2011 15:43:01 +0000 (16:43 +0100)]
arm: tcc8k: Fix indent, coding syle
Remove double definition of ACLKUSBH, change parameter name in
root_clk_disable, as there is no reason to have a different name than
in root_clk_enable.
No functional change.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de> Cc: bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Oskar Schirmer [Thu, 17 Feb 2011 15:43:00 +0000 (16:43 +0100)]
arm: tcc8k: Avoid reading clock register twice
There is no reason why in case of PLL2 the configuration register
should be read twice, while for PLL0/1 using the value previously read
is used. Do the same for PLL2.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de> Cc: bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hans J. Koch [Thu, 17 Feb 2011 15:42:59 +0000 (16:42 +0100)]
arm: tcc8k: Fix clock rate calculation
The calculation of the best divider value for a requested clock rate
always returned a value that was slightly too large. It was also not
protected against possible divisions by zero.
Request for very low, but non zero rates would cause the ACLK divisor
field to overflow. Catch this situation by using the maximum value.
The internal function aclk_set_rate() calculates the correct divider
value, but doesn't write it back to the register. Add the write back.
Signed-off-by: Hans J. Koch <hjk@linutronix.de> Signed-off-by: Oskar Schirmer <oskar@linutronix.de> Cc: bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Oskar Schirmer [Thu, 17 Feb 2011 15:42:58 +0000 (16:42 +0100)]
arm: tcc8k: Choose PLL settings conforming to board layout
The evaluation board is driven with 1.2V core voltage, so system clock
must not exceed 192 MHz, bus clock must not exceed 110 MHz. Choose
appropriate values and set DTCMWAIT accordingly. Adapt UART setting to
avoid console log interruption and wait for the specified locking time
of 300us to pass.
Signed-off-by: Oskar Schirmer <oskar@linutronix.de> Cc: bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Shawn Guo [Tue, 8 Mar 2011 10:51:09 +0000 (18:51 +0800)]
ARM: mx28: set proper parent for lcdif clock
Most likely, the LCD panel on mx28 platform will require a pixel
clock higher than ref_xtal_clk (24 MHz), so the patch initializes
the parent of lcdif clock as ref_pix_clk.
This typo was fixed in b4a2c28 (mx25: fix spi device registration typo), but a
the merge at 18990af6 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Linus Torvalds [Tue, 8 Mar 2011 04:46:39 +0000 (20:46 -0800)]
Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
Linus Torvalds [Tue, 8 Mar 2011 04:43:55 +0000 (20:43 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: index i shadowed in 2nd loop
drm/nv50-nvc0: prevent multiple vm/bar flushes occuring simultanenously
drm/nouveau: fix regression causing ttm to not be able to evict vram
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
Dmitry Shmidt [Thu, 3 Mar 2011 22:40:10 +0000 (17:40 -0500)]
mmc: sdio: Allow sdio operations in other threads during sdio_add_func()
This fixes a bug introduced by 554277e1730c ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com> Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
Dave Airlie [Mon, 7 Mar 2011 21:18:35 +0000 (07:18 +1000)]
Merge remote branch 'ickle/drm-intel-fixes' into drm-fixes
* ickle/drm-intel-fixes:
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
Linus Torvalds [Mon, 7 Mar 2011 21:14:19 +0000 (13:14 -0800)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] tape: deadlock on system work queue
[S390] keyboard: integer underflow bug
[S390] xpram: remove __initdata attribute from module parameters
The per-vm mutex doesn't prevent this completely, a flush coming from the
BAR VM could potentially happen at the same time as one for the channel
VM. Not to mention that if/when we get per-client/channel VM, this will
happen far more frequently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Shawn Guo [Sat, 5 Mar 2011 16:40:19 +0000 (00:40 +0800)]
ARM: mxs: add helper macro for pad control
This patch is to add pad control helper macro to make the code easy
to read. The need is being seen when adding pad definitions for
LCDIF which gets ~30 pads to define.
arch/arm/kernel/built-in.o: In function `__irq_svc':
io.c:(.text+0x2e0): undefined reference to `avic_base'
arch/arm/kernel/built-in.o: In function `__irq_usr':
io.c:(.text+0x4c8): undefined reference to `avic_base'
arch/arm/mach-mxc91231/built-in.o: In function `mxc91231_init_irq':
magx-zn5.c:(.init.text+0x18): undefined reference to `mxc_init_irq'
and was broken by
b0a0679 (ARM i.MX irq: Compile avic irq code only on SoCs that need it)
Sascha Hauer [Wed, 2 Mar 2011 08:27:42 +0000 (09:27 +0100)]
ARM i.MX: introduce imx_otg_ulpi_create to create ULPI transceivers
The boards are currently using otg_ulpi_create and mxc_ulpi_access_ops,
both are only present if CONFIG_USB_ULPI is set. To remove the need of
ifdefs in the board code introduce a imx_otg_ulpi_create functions
which expands to a static inline function if compiled without ulpi.
projects / kernel.git / log