Christophe Leroy [Fri, 10 May 2019 09:24:48 +0000 (09:24 +0000)]
powerpc: slightly improve cache helpers
Cache instructions (dcbz, dcbi, dcbf and dcbst) take two registers
that are summed to obtain the target address. Using 'Z' constraint
and '%y0' argument gives GCC the opportunity to use both registers
instead of only one with the second being forced to 0.
powerpc/mm/hugetlb: Don't enable HugeTLB if we don't have a page table cache
This makes sure we don't enable HugeTLB if the cache is not configured.
I am still not sure about this. IMHO hugetlb support should be a hardware
support derivative and any cache allocation failure should be handled as I did
in the earlier patch. But then if we were not able to create hugetlb page table
cache, we can as well declare hugetlb support disabled thereby avoiding calling
into allocation routines.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/hugetlb: Fix kernel crash if we fail to allocate page table caches
We only check for hugetlb allocations, because with hugetlb we do conditional
registration. For PGD/PUD/PMD levels we register them always in
pgtable_cache_init.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes kernel crash that arises due to not handling page table allocation
failures while allocating hugetlb page table.
Fixes: d067be3cb6d4 ("powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Remove radix dependency on HugeTLB page
Now that we have switched the page table walk to use pmd_is_leaf we can now
revert commit 31b2caf1e921 ("powerpc/mm/radix: Make Radix require HUGETLB_PAGE")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/book3s: Use config independent helpers for page table walk
Even when we have HugeTLB and THP disabled, kernel linear map can still be
mapped with hugepages. This is only an issue with radix translation because hash
MMU doesn't map kernel linear range in linux page table and other kernel
map areas are not mapped using hugepage.
Add config independent helpers and put WARN_ON() when we don't expect things
to be mapped via hugepages.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries/scm: Use a specific endian format for storing uuid from the device tree
We used uuid_parse to convert uuid string from device tree to two u64
components. We want to make sure we look at the uuid read from device
tree in an endian-neutral fashion. For now, I am picking little-endian
to be format so that we don't end up doing an additional conversion.
The reason to store in a specific endian format is to enable reading
the namespace created with a little-endian kernel config on a
big-endian kernel. We do store the device tree uuid string as a 64-bit
little-endian cookie in the label area. When booting the kernel we
also compare this cookie against what is read from the device tree.
For this, to work we have to store and compare these values in a CPU
endian config independent fashion.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/nvdimm: Add support for multibyte read/write for metadata
SCM_READ/WRITE_MEATADATA hcall supports multibyte read/write. This patch
updates the metadata read/write to use 1, 2, 4 or 8 byte read/write as
mentioned in PAPR document.
READ/WRITE_METADATA hcall supports the 1, 2, 4, or 8 bytes read/write.
For other values hcall results H_P3.
Hypervisor stores the metadata contents in big-endian format and in-order
to enable read/write in different granularity, we need to switch the contents
to big-endian before calling HCALL.
Based on an patch from Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries/scm: Mark the region volatile if cache flush not required
The device tree node is documented as below:
“ibm,cache-flush-required”:
property name indicates Cache Flush Required for this Persistent Memory Segment to persist memory
prop-encoded-array: None, this is a name only property.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/nvdimm: Add an informative message if we fail to allocate altmap block
Allocation from altmap area can fail based on vmemmap page size used.
Add kernel info message to indicate the failure. That allows the user
to identify whether they are really using persistent memory reserved
space for per-page metadata.
The message looks like:
[ 136.587212] altmap block allocation failed, falling back to system memory
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Reviewed-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm: Consolidate numa_enable check and min_common_depth check
If we fail to parse min_common_depth from device tree we boot with
numa disabled. Reflect the same by updating numa_enabled variable
to false. Also, switch all min_common_depth failure check to
if (!numa_enabled) check.
This helps us to avoid checking for both in different code paths.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we boot with numa=off, we need to make sure we return NUMA_NO_NODE when
looking up associativity details of resources. Without this, we hit crash
like below
powerpc/mm/drconf: Use NUMA_NO_NODE on failures instead of node 0
If we fail to parse the associativity array we should default to
NUMA_NO_NODE instead of NODE 0. Rest of the code fallback to the
right default if we find the numa node value NUMA_NO_NODE.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Use the right page size for vmemmap mapping
We use mmu_vmemmap_psize to find the page size for mapping the vmmemap area.
With radix translation, we are suboptimally setting this value to PAGE_SIZE.
We do check for 2M page size support and update mmu_vmemap_psize to use
hugepage size but we suboptimally reset the value to PAGE_SIZE in
radix__early_init_mmu(). This resulted in always mapping vmemmap area with
64K page size.
Fixes: c0e7ac9271a6 ("powerpc/mm/radix: Add radix callbacks for early init routines") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Protect against hogging the cpu while setting up the stats
When enabling or disabling the vcpu dispatch statistics, we do a lot of
work including allocating/deallocating memory across all possible cpus
for the DTL buffer. In order to guard against hogging the cpu for too
long, track the time we're taking and yield the processor if necessary.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For Shared Processor LPARs, the POWER Hypervisor maintains a
relatively static mapping of the LPAR processors (vcpus) to physical
processor chips (representing the "home" node) and tries to always
dispatch vcpus on their associated physical processor chip. However,
under certain scenarios, vcpus may be dispatched on a different
processor chip (away from its home node). The actual physical
processor number on which a certain vcpu is dispatched is available to
the guest in the 'processor_id' field of each DTL entry.
The guest can discover the home node of each vcpu through the
H_HOME_NODE_ASSOCIATIVITY(flags=1) hcall. The guest can also discover
the associativity of physical processors, as represented in the DTL
entry, through the H_HOME_NODE_ASSOCIATIVITY(flags=2) hcall.
These can then be compared to determine if the vcpu was dispatched on
its home node or not. If the vcpu was not dispatched on the home node,
it is possible to determine if the vcpu was dispatched in a different
chip, socket or drawer.
Introduce a procfs file /proc/powerpc/vcpudispatch_stats that can be
used to obtain these statistics. Writing '1' to this file enables
collecting the statistics, while writing '0' disables the statistics.
The statistics themselves are available by reading the procfs file. By
default, the DTLB log for each vcpu is processed 50 times a second so
as not to miss any entries. This processing frequency can be changed
through /proc/powerpc/vcpudispatch_stats_freq.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Move mm/book3s64/vphn.c under platforms/pseries/
hcall_vphn() is specific to pseries and will be used in a subsequent
patch. So, move it to a more appropriate place under
arch/powerpc/platforms/pseries. Also merge vphn.h into lppaca.h
and update vphn selftest to use the new files.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
H_HOME_NODE_ASSOCIATIVITY hcall can take two different flags and return
different associativity information in each case. Generalize the
existing hcall_vphn() function to take flags as an argument and to
return the result. Update the only existing user to pass the proper
arguments.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Introduce rwlock to gatekeep DTLB usage
Since we would be introducing a new user of the DTL buffer in a
subsequent patch, we need a way to gatekeep use of the DTL buffer.
The current debugfs interface for DTL allows registering and opening
cpu-specific DTL buffers. Cpu specific files are exposed under
debugfs 'powerpc/dtl/' node, and changing 'dtl_event_mask' in the same
directory enables controlling the event mask used when registering DTL
buffer for a particular cpu.
Subsequently, we will be introducing a user of the DTL buffers that
registers access to the DTL buffers across all cpus with the same event
mask. To ensure these two users do not step on each other, we introduce
a rwlock to gatekeep DTL buffer access. This fits the requirement of the
current debugfs interface wanting to allow multiple independent
cpu-specific users (read lock), and the subsequent user wanting
exclusive access (write lock).
Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Factor out DTL buffer allocation and registration routines
Introduce new helpers for DTL buffer allocation and registration and
have the existing code use those.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Don't split error messages across lines, for grepability] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/pseries: Do not save the previous DTL mask value
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is enabled, we always initialize
DTL enable mask to DTL_LOG_PREEMPT (0x2). There are no other places
where the mask is changed. As such, when reading the DTL log buffer
through debugfs, there is no need to save and restore the previous mask
value.
We don't need to save and restore the earlier mask value if
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not enabled. So, remove the field
from the structure as well.
Acked-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 764ef35f5d3a ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/4xx/uic: clear pending interrupt after irq type/pol change
When testing out gpio-keys with a button, a spurious
interrupt (and therefore a key press or release event)
gets triggered as soon as the driver enables the irq
line for the first time.
This patch clears any potential bogus generated interrupt
that was caused by the switching of the associated irq's
type and polarity.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
selftests/powerpc: Add missing newline at end of file
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[mpe: Rebase since addition of another test] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit a1dfdfb07b32 ("powerpc: Use barrier_nospec in copy_from_user()")
Added barrier_nospec before loading from user-controlled pointers. The
intention was to order the load from the potentially user-controlled
pointer vs a previous branch based on an access_ok() check or similar.
In order to achieve the same result, add a barrier_nospec to the
raw_copy_in_user() function before loading from such a user-controlled
pointer.
Fixes: a1dfdfb07b32 ("powerpc: Use barrier_nospec in copy_from_user()") Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 20 Jun 2019 06:00:40 +0000 (16:00 +1000)]
KVM: PPC: Book3S HV: Fix CR0 setting in TM emulation
When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
CR0 <- 0 || MSR[TS] || 0
This fixes the bit shift to put the bits in the correct location.
This is a data integrity issue as CR0 is corrupted.
Fixes: b5108510d7e3 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9") Cc: stable@vger.kernel.org # v4.17+ Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: Fix stale iommu table base after VFIO
The powernv platform uses @dma_iommu_ops for non-bypass DMA. These ops
need an iommu_table pointer which is stored in
dev->archdata.iommu_table_base. It is initialized during
pcibios_setup_device() which handles boot time devices. However when a
device is taken from the system in order to pass it through, the
default IOMMU table is destroyed but the pointer in a device is not
updated; also when a device is returned back to the system, a new
table pointer is not stored in dev->archdata.iommu_table_base either.
So when a just returned device tries using IOMMU, it crashes on
accessing stale iommu_table or its members.
This calls set_iommu_table_base() when the default window is created.
Note it used to be there before but was wrongly removed (see "fixes").
It did not appear before as these days most devices simply use bypass.
This adds set_iommu_table_base(NULL) when a device is taken from the
system to make it clear that IOMMU DMA cannot be used past that point.
The pseries platform uses the PCI_PROBE_DEVTREE method of PCI probing
which reads "assigned-addresses" of every PCI device and initializes
the device resources. However if the property is missing or zero sized,
then there is no fallback of any kind and the PCI resources remain
undiscovered, i.e. pdev->resource[] array remains empty.
This adds a fallback which parses the "reg" property in pretty much same
way except it marks resources as "unset" which later make Linux assign
those resources proper addresses.
This has an effect when:
1. a hypervisor failed to assign any resource for a device;
2. /chosen/linux,pci-probe-only=0 is in the DT so the system may try
assigning a resource.
Neither is likely to happen under PowerVM.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far the pseries platforms has always been using IOMMU making
SWIOTLB unnecessary. Now we want secure guests which means devices can
only access certain areas of guest physical memory; we are going to
use SWIOTLB for this purpose.
This allows SWIOTLB for pseries. By default there is no change in
behavior.
This enables SWIOTLB when the "swiotlb" kernel parameter is set to
"force".
With the SWIOTLB enabled, the kernel creates a directly mapped DMA
window (using the usual DDW mechanism) and implements SWIOTLB on top
of that.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The commit 069a5b89854a ("powerpc/dma: handle iommu bypass in
dma_iommu_ops") merged direct DMA ops into the IOMMU DMA ops allowing
SWIOTLB as well but only for mapping; the unmapping and bouncing parts
were left unmodified.
This adds missing direct unmapping calls to .unmap_page() and
.unmap_sg().
This adds missing sync callbacks and directs them to the direct DMA
hooks.
Michael Neuling [Tue, 4 Jun 2019 03:00:37 +0000 (13:00 +1000)]
powerpc: Fix compile issue with force DAWR
If you compile with KVM but without CONFIG_HAVE_HW_BREAKPOINT you fail
at linking with:
arch/powerpc/kvm/book3s_hv_rmhandlers.o:(.text+0x708): undefined reference to `dawr_force_enable'
This was caused by commit 57dc8a09c9b4 ("powerpc: Add force enable of
DAWR on P9 option").
This moves a bunch of code around to fix this. It moves a lot of the
DAWR code in a new file and creates a new CONFIG_PPC_DAWR to enable
compiling it.
Fixes: 57dc8a09c9b4 ("powerpc: Add force enable of DAWR on P9 option") Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Minor formatting in set_dawr()] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since GCC 8 this triggers the following warning about incompatible
function types:
arch/powerpc/kernel/hw_breakpoint.c:408:21: error: cast between incompatible function types from 'int (*)(struct arch_hw_breakpoint *)' to 'void (*)(void *)' [-Werror=cast-function-type]
Since the warning is there for a reason, and should not be hidden behind
a cast, provide an intermediate callback function to avoid the warning.
Fixes: 57dc8a09c9b4 ("powerpc: Add force enable of DAWR on P9 option") Suggested-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sun, 23 Jun 2019 10:41:52 +0000 (20:41 +1000)]
powerpc/64s/radix: keep kernel ERAT over local process/guest invalidates
ISA v3.0 radix modes provide SLBIA variants which can invalidate ERAT
for effPID!=0 or for effLPID!=0, which allows user and guest
invalidations to retain kernel/host ERAT entries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 06:33:22 +0000 (16:33 +1000)]
powerpc/64s/exception: simplify hmi control flow
Branch to the relocated 0xc000 address early (still in real mode), to
simplify subsequent branches. Have the virt mode handler avoid just
'windup' and redo the exception from scratch, rather than branching
back to the trampoline.
Rearrange the stack setup instruction location to match the system
reset handler (e.g., right before EXCEPTION_PROLOG_COMMON).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 06:33:19 +0000 (16:33 +1000)]
powerpc/64s/exception: optimise system_reset for idle, clean up non-idle case
The idle wake up code in the system reset interrupt is not very
optimal. There are two requirements: perform idle wake up quickly;
and save everything including CFAR for non-idle interrupts, with
no performance requirement.
The problem with placing the idle test in the middle of the handler
and using the normal handler code to save CFAR, is that it's quite
costly (e.g., mfcfar is serialising, speculative workarounds get
applied, SRR1 has to be reloaded, etc). It also prevents the standard
interrupt handler boilerplate being used.
This pain can be avoided by using a dedicated idle interrupt handler
at the start of the interrupt handler, which restores all registers
back to the way they were in case it was not an idle wake up. CFAR
is preserved without saving it before the non-idle case by making that
the fall-through, and idle is a taken branch.
Performance seems to be in the noise, but possibly around 0.5% faster,
the executed instructions certainly look better. The bigger benefit is
being able to drop in standard interrupt handlers after the idle code,
which helps with subsequent cleanup and consolidation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fixup BE by using DOTSYM for idle_return_gpr_loss call] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 06:33:18 +0000 (16:33 +1000)]
powerpc/64s/exception: remove bad stack branch
The bad stack test in interrupt handlers has a few problems. For
performance it is taken in the common case, which is a fetch bubble
and a waste of i-cache.
For code development and maintainence, it requires yet another stack
frame setup routine, and that constrains all exception handlers to
follow the same register save pattern which inhibits future
optimisation.
Remove the test/branch and replace it with a trap. Teach the program
check handler to use the emergency stack for this case.
This does not result in quite so nice a message, however the SRR0 and
SRR1 of the crashed interrupt can be seen in r11 and r12, as is the
original r1 (adjusted by INT_FRAME_SIZE). These are the most important
parts to debugging the issue.
The original r9-12 and cr0 is lost, which is the main downside.
Nicholas Piggin [Fri, 28 Jun 2019 05:33:32 +0000 (15:33 +1000)]
powerpc/tm: update comment about interrupt re-entrancy
Since the system reset interrupt began to use its own stack, and
machine check interrupts have done so for some time, r1 can be
changed without clearing MSR[RI], provided no other interrupts
(including SLB misses) are taken.
MSR[RI] does have to be cleared when using SCRATCH0, however.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 05:33:26 +0000 (15:33 +1000)]
powerpc/64s/exception: shuffle windup code around
Restore all SPRs and CR up-front, these are longer latency
instructions. Move register restore around to maximise pairs of
adjacent loads (e.g., restore r0 next to r1).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 05:33:25 +0000 (15:33 +1000)]
powerpc/64s/exception: simplify hmi windup code
Duplicate the hmi windup code for both cases, rather than to put a
special case branch in the middle of it. Remove unused label. This
helps with later code consolidation.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 28 Jun 2019 05:33:20 +0000 (15:33 +1000)]
powerpc/64s/exception: clean up system call entry
syscall / hcall entry unnecessarily differs between KVM and non-KVM
builds. Move the SMT priority instruction to the same location
(after INTERRUPT_TO_KERNEL).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Generally, macros that result in instructions being expanded are
indented by a tab, and those that don't have no indent. Fix the
obvious cases that go contrary to style.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 22 Jun 2019 13:15:21 +0000 (23:15 +1000)]
powerpc/64s/exception: Move EXCEPTION_COMMON additions into callers
More cases of code insertion via macros that does not add a great
deal. All the additions have to be specified in the macro arguments,
so they can just as well go after the macro.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 22 Jun 2019 13:15:20 +0000 (23:15 +1000)]
powerpc/64s/exception: Move EXCEPTION_COMMON handler and return branches into callers
The aim is to reduce the amount of indirection it takes to get through
the exception handler macros, particularly where it provides little
code sharing.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 22 Jun 2019 13:15:15 +0000 (23:15 +1000)]
powerpc/64s/exception: remove the "extra" macro parameter
Rather than pass in the soft-masking and KVM tests via macro that is
passed to another macro to expand it, switch to usig gas macros and
conditionally expand the soft-masking and KVM tests.
The system reset with its idle test is open coded as it is a one-off.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 22 Jun 2019 13:15:14 +0000 (23:15 +1000)]
powerpc/64s/exception: fix sreset KVM test code
The sreset handler KVM test theoretically should not depend on P7.
In practice KVM now only supports P7 and up so no real bug fix, but
this change is made now so the quirk is not propagated through
cleanup patches.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Sat, 22 Jun 2019 13:15:11 +0000 (23:15 +1000)]
powerpc/64s/exception: remove H concatenation for EXC_HV variants
Replace all instances of this with gas macros that test the hsrr
parameter and use the appropriate register names / labels.
No generated code change.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Remove extraneous 2nd check for 0xea0 in SOFTEN_TEST] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove SOFTEN_VALUE_0x980, it's been unused since commit 89cfa78ca2e8 ("powerpc: Give hypervisor decrementer interrupts their
own handler") (Sep 2012).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv: remove the unused pnv_pci_set_p2p function
This function has never been used anywhere in the kernel tree since it
was added to the tree. We also now have proper PCIe P2P APIs in the core
kernel, and any new P2P support should be using those.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Naveen N. Rao [Thu, 27 Jun 2019 09:59:40 +0000 (15:29 +0530)]
powerpc/xmon: Fix disabling tracing while in xmon
Commit f60c0c5893783 ("powerpc/xmon: Disable tracing when entering
xmon") added code to disable recording trace entries while in xmon. The
commit introduced a variable 'tracing_enabled' to record if tracing was
enabled on xmon entry, and used this to conditionally enable tracing
during exit from xmon.
However, we are not checking the value of 'fromipi' variable in
xmon_core() when setting 'tracing_enabled'. Due to this, when secondary
cpus enter xmon, they will see tracing as being disabled already and
tracing won't be re-enabled on exit. Fix the same.
Fixes: f60c0c5893783 ("powerpc/xmon: Disable tracing when entering xmon") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>