Emanuele Ghidoli [Thu, 16 Feb 2023 11:31:15 +0000 (12:31 +0100)]
configs: verdin-imx8mp: Fix wrong early malloc() heap size
Set, previously unset, CONFIG_SPL_SYS_MALLOC_F_LEN to 0x4000 whose
default value is 0x10000.
Early malloc() uses CRAM_S at 0x184000 (CFG_MALLOC_F_ADDR), this ram
area end at 0x188000.
Rasmus Villemoes [Wed, 22 Mar 2023 14:42:05 +0000 (15:42 +0100)]
ARM: imx: imx8mp: fix enable_i2c_clk
In order for i2c_num==4 and 5 to stay invalid for non-imx8mp SOCs, the
i2c_ccgr[] array must be sized by the number of initializers present,
not with a hard-coded 6 which would implicitly initialize the last two
elements with zeroes.
Also, the bounds check is off-by-one.
Fixes: c027e1f191a5 "ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP" Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Marek Vasut [Mon, 6 Mar 2023 14:53:51 +0000 (15:53 +0100)]
net: fec_mxc: Add board_interface_eth_init() for i.MX8M Mini/Nano/Plus
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Marek Vasut [Mon, 6 Mar 2023 14:53:50 +0000 (15:53 +0100)]
net: fec_mxc: Add ref clock setup support for i.MX8M Mini/Nano/Plus
The FEC ref clock frequency on i.MX8M Mini/Nano/Plus was so far configured
via ad-hoc board code. Replace that with DM clock clk_set_rate() instead.
This way, the driver claims all its required clock and sets the ref clock
rate, without any need of architecture specific register fiddling.
Marek Vasut [Mon, 6 Mar 2023 14:53:49 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add board_interface_eth_init() for i.MX8M Plus
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:48 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add i.MX8M Plus RMII support
With DM clock support in place, it is easy to add RMII support into the
MAC driver. The RMII cannot operate at 1000 Mbps and at 100 and 10 Mbps
the clock frequency is 50 MHz and 5 MHz instead of 25 MHz and 2.5 MHz.
The board DT requires the following adjustments to EQoS node:
phy-mode = "rmii";
assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>,
<&clk IMX8MP_SYS_PLL2_100M>,
<&clk IMX8MP_SYS_PLL2_50M>;
assigned-clock-rates = <0>, <100000000>, <50000000>;
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:47 +0000 (15:53 +0100)]
net: dwc_eth_qos: Add DM CLK support for i.MX8M Plus
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Marek Vasut [Mon, 6 Mar 2023 14:53:46 +0000 (15:53 +0100)]
net: dwc_eth_qos: Set DMA_MODE SWR bit to reset the MAC
The driver currently only waits for DMA_MODE SWR bit to clear itself.
This is insufficient e.g. on i.MX8M Plus, where the MAC must be reset
before IOMUX GPR[1] content is latched into the MAC and used. Without
the proper reset, the i.MX8M Plus MAC variant does not take the value
in IOMUX GPR[1] into account, which makes it impossible e.g. to switch
interface mode from RGMII to any other.
Since proper reset is desired in general to put the block into defined
state, always assert the DMA_MODE SWR bit before waiting for the bit
to clear itself.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marek Vasut [Mon, 6 Mar 2023 14:53:44 +0000 (15:53 +0100)]
net: dwc_eth_qos: Drop unused dm_gpio_free() on STM32
The dm_gpio_free() is never called, because for stm32, the phy_reset_gpio
pointer is never valid. This is because only tegra186 ever claims the
phy_reset_gpio, all other platforms use the PHY framework to reset the
PHY instead. Drop the dm_gpio_free() and dm_gpio_is_valid().
Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Marek Vasut <marex@denx.de>
Marcel Ziswiler [Fri, 3 Mar 2023 13:26:37 +0000 (14:26 +0100)]
colibri-imx8x: update env memory layout
Update the distro config env memory layout for the Colibri iMX8X:
- kernel_comp_addr_r=0xb0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Idea of memory layout taken from commit bf1c94c46d71
("apalis-imx8: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Marek Vasut [Thu, 2 Mar 2023 22:40:44 +0000 (23:40 +0100)]
ARM: dts: imx: Add support for DH electronics i.MX8M Plus DHCOM on PDK3
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
misc: imx: remove DM dependency for ocotp driver in SPL
The ocotp driver is available for regular and SPL builds using the
(SPL_)MXC_OCOTP configuration. Also, the ocotp driver does not support
the driver model (DM) configuration.
But, for SPL builds, the SPL_MXC_OCOTP configuration depends on
SPL_MISC which implies on SPL_DM.
This commit replaces the dependency on SPL_MISC with SPL_DRIVERS_MISC.
So the only requirement is to have enabled miscellaneous drivers for
the SPL.
Signed-off-by: Jean-Marie Lemetayer <j.lemetayer@kerlink.fr>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Marek Vasut [Sat, 11 Feb 2023 22:10:50 +0000 (23:10 +0100)]
arm64: imx8mp: Auto-detect PHY on i.MX8MP DHCOM
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Marek Vasut [Sat, 11 Feb 2023 21:49:01 +0000 (22:49 +0100)]
ARM: imx: Add 2 GiB DRAM support for DH electronics i.MX8M Plus DHCOM
The DH electronics i.MX8M Plus DHCOM SoM currently supports only 4 GiB
of DRAM population option. Add another population option with 2 GiB of
DRAM. The chips used on the 2 GiB option are 2x K4F6E3S4HM-MGCJ .
configs: colibri-imx7: Fix bad block table in flash configuration
Make sure that the bad block table in flash is used on Colibri iMX7.
Without this configuration enabled U-Boot corrupts the bad block table
and Linux will update the table on each reboot. The corruption occurs
because if CONFIG_SYS_NAND_USE_FLASH_BBT is not set, U-boot will store
bad blocks out of band, while the Linux driver for the iMX7 will store
them in band in a bad block table.
Fixes: e0af4a568aa ("arm: dts: imx7: colibri: add raw NAND support") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Ye Li [Fri, 3 Feb 2023 10:24:36 +0000 (18:24 +0800)]
power: pmic: Add NXP PCA9451A PMIC support
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de>
Fabio Estevam [Wed, 15 Feb 2023 18:24:44 +0000 (15:24 -0300)]
pico-imx6: Pass the mmc alias to fix boot regression
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit c2092e38fd66 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: c2092e38fd66 ("imx6dl/imx6qdl: synchronise device trees with linux") Signed-off-by: Fabio Estevam <festevam@denx.de>
Ye Li [Tue, 31 Jan 2023 08:42:34 +0000 (16:42 +0800)]
imx8ulp_evk: Clear data at fdt_addr_r before booting kernel
When using dual boot mode, the DDR won't be reset when APD power off
or reboot. It has possibility that obsolete fdt data existing on
fdt_addr_r address. Then even nothing in EFI partitions, the distro boot
still continue to parse fdt and get uboot crashed.
Clear the data at fdt_addr_r, so the fdt header check in above case
will not pass.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 31 Jan 2023 08:42:33 +0000 (16:42 +0800)]
imx8ulp_evk: disable overflow of port0 for LPAV
Bit0: Port 0 behavior when bandwidth maximized. Set to 1 to allow overflow
With overflow set, we see some issue that A35 may not able to get enough
bandwidth and A35 will report hrtimer takes too much time, workqueue
lockup. With overflow cleared, the issues are gone.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:32 +0000 (16:42 +0800)]
imx8ulp_evk: Update DDR ports arbitration for DCNANO underrun
To resolve DCNANO underrun issue, change the DDR Port 0 arbitration
from round robin fashion to fixed priority level 1, while other ports
are not assigned any priority, so they will be serviced in round robin
fashion if there is no active request from Port 0.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:28 +0000 (16:42 +0800)]
misc: fuse: Lock 8ULP ECC-protected fuse when programming
The ECC fuse on 8ULP can't be written twice. If any user did it, the
ECC value would be wrong then cause accessing problem to the fuse.
The patch will lock the ECC fuse word to avoid this problem.
For iMX9, the OTP controller automatically prevents an ECC fuse word to
be written twice. So it does not need the setting.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:27 +0000 (16:42 +0800)]
misc: fuse: Update fuse mapping for 8ULP S400 API
Since new 8ULP A1 S400 FW (v0.0.8-e329b760) can support to read
more fuses: like PMU trim, Test flow/USB, GP1-5, GP8-10. Update
the u-boot driver for the new mapping.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Alice Guo <alice.guo@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:26 +0000 (16:42 +0800)]
imx: sentinel: Update S400 API get info message structure
From Sentinel FW v0.0.9-9df0f503, the response message of get info API
is changed to add OEM SRK and some states (IMEM, CSAL, TRNG).
With old structure, we get failure from sentinel due to the buffer
size can't fit with new response message. So update the API structure
to fix the issue.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:24 +0000 (16:42 +0800)]
imx: imx8ulp: Configure XRDC PDAC and MSC for DBD owner=S400 only
This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 31 Jan 2023 08:42:22 +0000 (16:42 +0800)]
imx: imx8ulp: upower: replace magic number with macro
The swton indicates the logic switch, magic number 0xfff80 is hard
to understand, so use macro.
Some board design may not have MIPI_CSI voltage input connected per
data sheet. In that case, the upower power on API may dead loop mu to wait
response, however there is no response. So remove MIPI_CSI here, let
linux power domain driver to runtime enable the power domain.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:21 +0000 (16:42 +0800)]
imx: imx8ulp: Clear dividers in PLL3DIV_PFD registers
At present, in cgc1_pll3_init we don't set the pll3pfd div values,
just use the default 0. But on A1 part, ROM will set PLL3 pfd1div2
to 1 and pfd2div1 to 3.
This finally causes some clocks' rate decreased, for example USDHC.
So clear the PLL3DIV_PFD dividers to get correct rate.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:20 +0000 (16:42 +0800)]
imx: imx8ulp: Reconfigure MRC3 for SRAM0 access
Some space in SRAM0 will be protected by S400 to allow RX SecPriv mode
access only for boot purpose. Since SW will reuse the SRAM0 as SCMI
buffer and SPL container loading buffer, need to reconfigure MRC3.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:19 +0000 (16:42 +0800)]
ddr: imx8ulp: Change DRAM timing save area to 0x20055000
To align with ARM trusted firmware's change, adjust DRAM timing
save area to new position 0x20055000. So we can release the space
since 0x2006c000 for the NOBITS region of ARM trusted firmware
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:17 +0000 (16:42 +0800)]
imx: imx8ulp: Adjust handshake to sync TRDC and XRDC completion
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:16 +0000 (16:42 +0800)]
imx: imx8ulp: Remove the TRDC configure from A35
As M33 is responsible for TRDC configuration, the settings for A35
nonsecure world access and DMA0 access are moved to M33 image.
So remove the codes to release TRDC and configure it. Just keep
the configurations for reference.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:13 +0000 (16:42 +0800)]
imx: imx8ulp: Get chip revision from Sentinel
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:12 +0000 (16:42 +0800)]
imx: imx8ulp: Fix MU device probe failure
Since latest DTS has added multiple MU nodes, using compatible
string to find the device node is not proper. It finds the first
node with the compatible string matched even the node is disabled.
Tom Rini [Mon, 27 Mar 2023 15:16:51 +0000 (11:16 -0400)]
Merge branch '2023-03-27-rockchip-rk3399-fixes'
- A series of minor cleanups to DISTRO_DEFAULTS and BOOTSTD so that the
rk3399 bootstd migration can be complete and functional now, and make
future migrations easier.
Tom Rini [Fri, 24 Mar 2023 20:58:15 +0000 (16:58 -0400)]
rockchip: Use BOOTSTD_DEFAULTS if not DISTRO_DEFAULTS
When we do not enable DISTRO_DEFAULTS (generally, to get distro_bootcmd)
we instea do want to imply BOOTSTD_DEFAULTS so that when using bootstd
the general distro boot functionality will still work.
Simon Glass [Fri, 24 Mar 2023 20:58:13 +0000 (16:58 -0400)]
boot: Create a common BOOT_DEFAULTS for distro and bootstd
These two features use a lot of common options. Move them into a common
CONFIG to reduce duplication.
Use 'select' for most options since these are things that boards aren't
supposed to override. For now it is not possible to disable
BOOT_DEFAULTS but we may take another look later.
Note that five options use 'imply' to match existing behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so we don't grow so many platforms unintentionally] Signed-off-by: Tom Rini <trini@konsulko.com>
projects / uboot.git / log