Marek Vasut [Fri, 25 Mar 2022 17:59:28 +0000 (18:59 +0100)]
ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mn board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Because the Beacon imx8mm board uses device tree
for MMC/SD and Ethernet, there is no need to have some of the
config options. It's handled by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Tue, 15 Mar 2022 20:47:05 +0000 (17:47 -0300)]
tbs2910: Convert to DM_SERIAL
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Tim Harvey [Tue, 8 Mar 2022 00:24:04 +0000 (16:24 -0800)]
drivers: misc: add Gateworks System Controller driver
Add a driver for the Gateworks System Controller used on Gateworks boards
which provides a boot watchdog, power control, temperature monitor,
and voltage ADCs.
Tim Harvey [Tue, 8 Mar 2022 00:24:03 +0000 (16:24 -0800)]
board: gateworks: gw_ventana: move ft_early_fixups out of common
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Tim Harvey [Tue, 8 Mar 2022 00:24:01 +0000 (16:24 -0800)]
board: gateworks: gw_ventana: move SPL uart config out of common
Since DM_SERIAL is used for U-Boot we no longer need legacy UART code in
common.c shared by the SPL and U-Boot. Move the legacy UART config to
the non-DM SPL.
Tim Harvey [Tue, 8 Mar 2022 00:24:00 +0000 (16:24 -0800)]
board: gateworks: gw_ventana: convert to DM_I2C
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Heiko Thiery [Sat, 26 Feb 2022 09:44:21 +0000 (10:44 +0100)]
ARM: imx: imx8mn-evk: enable DM_SERIAL
U-Boot complains that CONFIG_SERIAL is not converted to CONFIG_DM_SERIAL
and gives a deadline before possibly removing the board. Migrate to
DM_SERIAL to fulfill the request.
Marek Vasut [Sat, 26 Feb 2022 03:37:08 +0000 (04:37 +0100)]
pmic: pca9450: Add PCA9450C compatible string
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
The correct compatible string for i.MX8MP variant of DWC EQoS MAC
is "nxp,imx8mp-dwmac-eqos", use it. Drop the two current users of
the current wrong compatible string to avoid breaking them.
Adam Ford [Wed, 23 Feb 2022 13:50:51 +0000 (07:50 -0600)]
imx: imx8mm/imx8mn_beacon: Remove redundant code
The Ethernet controller and PHY use the device tree info to
configure themselves, so it's not necessary to manually do it
in the board file. This permits the removal of a bunch of headers
as well.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
Heiko Thiery [Wed, 23 Feb 2022 09:48:26 +0000 (10:48 +0100)]
ARM: imx: imx8mn-*-evk: use reset-gpios in phy node
To be in sync with the linux devicetree change the 'phy-reset-gpios' in
the fec node to 'reset-gpios' in the phy node. The PHY reset will be
done by the eth-phy-uclass driver while probing the PHY. This is ok
since it is done before probing the fec.
Heiko Thiery [Wed, 23 Feb 2022 08:10:29 +0000 (09:10 +0100)]
ARM: imx: imx8mn-*-evk: use DM settings for PHY configuration
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK Reviewed-by: Fabio Estevam <festevam@gmail.com>
CPU: Freescale i.MX6DL rev1.3 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 40C
Reset cause: POR
Model: BTicino i.MX6DL Mamoj board
DRAM: 512 MiB
Core: 29 devices, 12 uclasses, devicetree: separate
MMC: FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@2188000 address not set.
No ethernet found.
LS1043ARDB, LS1046ARDB, LS1088ARDB: Enable SPL_OF_CONTROL in SECURE Boot defconfig
If enable SPL_DM without SPL_OF_CONTROL,
build errors "undefined reference to fdt_get_resource",
is coming in function `caam_jr_probe'.
Added SPL_OF_CONTROL to remove the error.
Tom Rini [Sun, 10 Apr 2022 15:21:39 +0000 (11:21 -0400)]
Merge tag 'efi-2022-07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1
Documentation:
* Describe how enable DM_SERIAL for a board
UEFI
* Preparatory patches for better integration of DM and UEFI
* Use sysreset after capsule updates instead of do_reset
* Allow to disable persisting non-volatile variables
This commit broke environment on literally every board I have access
to, with this revert in place, environment works as it should again.
The problem I observe with this patch is that saved environment in
either SPI NOR or eMMC is never used, the system always falls back
to default environment. The 'saveenv' command does succeed, but then
after reset, the default env is again used.
Furthermore, the commit introduced duplicate code in env_init(), this:
"
if (!prio) {
gd->env_addr = (ulong)&default_environment[0];
gd->env_valid = ENV_INVALID;
Also note that upstream does not support UltraZed EG board, so
this might have been a patch pulled from downstream which did
depend on some other downstream behavior.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Felix.Vietmeyer@jila.colorado.edu <felix.vietmeyer@jila.colorado.edu> Cc: Tom Rini <trini@konsulko.com>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:46 +0000 (20:36 +0900)]
dm: add tag support
With dm-tag feature, any U-Boot subsystem is allowed to associate
arbitrary number of data with a particular udevice. This can been
see as expanding "struct udevice" without modifying the definition.
As a first user, UEFI subsystem makes use of tags to associate
an efi_disk object with a block device.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:45 +0000 (20:36 +0900)]
virtio: call device_probe() in scanning
virtio_init() enumerates all the peripherals that are to be materialised
with udevices(UCLASS_VIRIO) and creates particular device instances
(UCLASS_BlK or whatever else) as children.
On the other hand, device_probe() won't be invoked against those resultant
udevices unlike other ordinary device drivers do in the driver model.
This is particularly inconvenient when we want to add "event notification"
callback so that we will be able to automatically create all efi_disk
objects in a later patch.
With this patch applied, "virtio scan" will work in a similar way
to "scsi rescan", "usb start" or others in term of 'probe' semantics.
I didn't add this change to virtio_init() itself because this function
may be called in board_init_r() (indirectly in board_late_init())
before UEFI subsustem is initialized.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:44 +0000 (20:36 +0900)]
block: ide: call device_probe() after scanning
Every time an ide bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:43 +0000 (20:36 +0900)]
sata: call device_probe() after scanning
Every time a sata bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:42 +0000 (20:36 +0900)]
nvme: call device_probe() after scanning
Every time a nvme bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:41 +0000 (20:36 +0900)]
mmc: call device_probe() after scanning
Every time a mmc bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:40 +0000 (20:36 +0900)]
usb: storage: call device_probe() after scanning
Every time a usb bus/port is scanned and a new device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 8 Mar 2022 11:36:39 +0000 (20:36 +0900)]
scsi: call device_probe() after scanning
Every time a scsi bus/port is scanned and a new block device is detected,
we want to call device_probe() as it will give us a chance to run
additional post-processings for some purposes.
In particular, support for creating partitions on a device will be added.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Masami Hiramatsu [Mon, 21 Mar 2022 13:37:56 +0000 (22:37 +0900)]
efi_loader: Use sysreset instead of reset command
Use sysreset_walk_halt() directly from reset-after-capsule-on-disk
feature to reboot (cold reset) machine instead of using reset command
interface, since this is not a command.
Note that this will make CONFIG_EFI_CAPSULE_ON_DISK depending on
the CONFIG_SYSRESET.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Masami Hiramatsu [Mon, 21 Mar 2022 13:37:45 +0000 (22:37 +0900)]
efi_loader: Make efi_load_capsule_drivers() available even if EFI_CAPSULE_ON_DISK=n
Make efi_load_capsule_drivers() available even if EFI_CAPSULE_ON_DISK
is disabled because the caller (efi_init_obj_list()) expects it only
relays on EFI_HAVE_CAPSULE_SUPPORT.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Masami Hiramatsu [Mon, 21 Mar 2022 13:37:35 +0000 (22:37 +0900)]
cmd: efidebug: Disable 'capsule disk-update' when CONFIG_EFI_CAPSULE_ON_DISK=n
Disable 'capsule disk-update' option for the efidebug command
when CONFIC_EFI_CAPSULE_ON_DISK is disabled, because this option
is available only when the EFI capsule update on disk is enabled.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Saeger [Tue, 22 Mar 2022 21:21:10 +0000 (15:21 -0600)]
efi_loader: optional persistence of variables
Since 7e9d1dd5e10b ("efi_loader: configuration of variables store")
the choice of EFI_VARIABLE_FILE_STORE or EFI_MM_COMM_TEE
is mutually-exclusive, however efi_var_to_file also allows
for "neither". Provide an additional Kconfig option.
Signed-off-by: Tom Saeger <tom.saeger@oracle.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Eddie James [Mon, 7 Feb 2022 23:09:01 +0000 (17:09 -0600)]
gpio: Enable hogging support in SPL
Use the CONFIG macros to conditionally build the GPIO hogging support in
either the SPL or U-Boot, or both, depending on the configuration. Also
call the GPIO hog probe function in the common SPL board initialization
as an equivalent to adding it to the U-Boot init sequence functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Andrew Jeffery [Mon, 31 Jan 2022 03:24:05 +0000 (13:54 +1030)]
gpio: Add gpio_request_by_line_name()
Add support for the upstream gpio-line-names property already described
in the common GPIO binding document[1]. The ability to search for a line
name allows boards to lift the implementation of common GPIO behaviours
away from specific line indexes on a GPIO controller.
Tom Rini [Wed, 30 Mar 2022 22:07:23 +0000 (18:07 -0400)]
spi: cadence_qspi: Migrate CONFIG_CQSPI_REF_CLK to Kconfig
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 30 Mar 2022 22:07:18 +0000 (18:07 -0400)]
corvus: Migrate CONFIG_*_LED out of CONFIG namespace
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Tom Rini [Wed, 30 Mar 2022 22:07:16 +0000 (18:07 -0400)]
s5p_goni, smdkc100: Move some environment settings out of CONFIG
A number of CONFIG options are used on these platforms as part of the
default environment. Set some of these more directly and in other
cases, just reference them directly.
Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 30 Mar 2022 22:07:15 +0000 (18:07 -0400)]
arm: integrator: Migrate platform-specific options and cleanup armcoremodule.h
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 8 Apr 2022 12:27:50 +0000 (08:27 -0400)]
Merge branch '2022-04-08-env-updates'
- Assorted env tooling updates
- Bug fix around multiple possible env locations and ENV_IS_NOWHERE
- Add 'indirect' sub-command to env
- Allow for FAT env to have the location overridden by the board code.
Simon Glass [Sun, 13 Mar 2022 05:47:49 +0000 (22:47 -0700)]
env: Allow text-env tests to run with awk
At present the tests assume that gawk is being used. Adjust the tests so
that the names are inserted in alphabetical order, so that awk is happy.
Also use PROCINFO to make gawk output in alphabetical order. This is not
ideal, since it changes the env-car ordering from what the user provided,
but it may be acceptable.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Fixes: https://source.denx.de/u-boot/u-boot/-/issues/10
projects / uboot.git / log