Aravinda Prasad [Thu, 11 May 2017 11:03:37 +0000 (16:33 +0530)]
KVM: PPC: Book3S HV: Exit guest upon MCE when FWNMI capability is enabled
Enhance KVM to cause a guest exit with KVM_EXIT_NMI
exit reason upon a machine check exception (MCE) in
the guest address space if the KVM_CAP_PPC_FWNMI
capability is enabled (instead of delivering a 0x200
interrupt to guest). This enables QEMU to build error
log and deliver machine check exception to guest via
guest registered machine check handler.
This approach simplifies the delivery of machine
check exception to guest OS compared to the earlier
approach of KVM directly invoking 0x200 guest interrupt
vector.
This design/approach is based on the feedback for the
QEMU patches to handle machine check exception. Details
of earlier approach of handling machine check exception
in QEMU and related discussions can be found at:
This patch now directly invokes machine_check_print_event_info()
from kvmppc_handle_exit_hv() to print the event to host console
at the time of guest exit before the exception is passed on to the
guest. Hence, the host-side handling which was performed earlier
via machine_check_fwnmi is removed.
The reasons for this approach is (i) it is not possible
to distinguish whether the exception occurred in the
guest or the host from the pt_regs passed on the
machine_check_exception(). Hence machine_check_exception()
calls panic, instead of passing on the exception to
the guest, if the machine check exception is not
recoverable. (ii) the approach introduced in this
patch gives opportunity to the host kernel to perform
actions in virtual mode before passing on the exception
to the guest. This approach does not require complex
tweaks to machine_check_fwnmi and friends.
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Aravinda Prasad [Thu, 11 May 2017 11:02:48 +0000 (16:32 +0530)]
KVM: PPC: Book3S HV: Add new capability to control MCE behaviour
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Tue, 20 Jun 2017 05:46:12 +0000 (15:46 +1000)]
KVM: PPC: Book3S HV: Don't sleep if XIVE interrupt pending on POWER9
On a POWER9 system, it is possible for an interrupt to become pending
for a VCPU when that VCPU is about to cede (execute a H_CEDE hypercall)
and has already disabled interrupts, or in the H_CEDE processing up
to the point where the XIVE context is pulled from the hardware. In
such a case, the H_CEDE should not sleep, but should return immediately
to the guest. However, the conditions tested in kvmppc_vcpu_woken()
don't include the condition that a XIVE interrupt is pending, so the
VCPU could sleep until the next decrementer interrupt.
To fix this, we add a new xive_interrupt_pending() helper which looks
in the XIVE context that was pulled from the hardware to see if the
priority of any pending interrupt is higher (numerically lower than)
the CPU priority. If so then kvmppc_vcpu_woken() will return true.
If the XIVE context has never been used, then both the pipr and the
cppr fields will be zero and the test will indicate that no interrupt
is pending.
Paul Mackerras [Tue, 16 May 2017 06:41:20 +0000 (16:41 +1000)]
KVM: PPC: Book3S HV: Virtualize doorbell facility on POWER9
On POWER9, we no longer have the restriction that we had on POWER8
where all threads in a core have to be in the same partition, so
the CPU threads are now independent. However, we still want to be
able to run guests with a virtual SMT topology, if only to allow
migration of guests from POWER8 systems to POWER9.
A guest that has a virtual SMT mode greater than 1 will expect to
be able to use the doorbell facility; it will expect the msgsndp
and msgclrp instructions to work appropriately and to be able to read
sensible values from the TIR (thread identification register) and
DPDES (directed privileged doorbell exception status) special-purpose
registers. However, since each CPU thread is a separate sub-processor
in POWER9, these instructions and registers can only be used within
a single CPU thread.
In order for these instructions to appear to act correctly according
to the guest's virtual SMT mode, we have to trap and emulate them.
We cause them to trap by clearing the HFSCR_MSGP bit in the HFSCR
register. The emulation is triggered by the hypervisor facility
unavailable interrupt that occurs when the guest uses them.
To cause a doorbell interrupt to occur within the guest, we set the
DPDES register to 1. If the guest has interrupts enabled, the CPU
will generate a doorbell interrupt and clear the DPDES register in
hardware. The DPDES hardware register for the guest is saved in the
vcpu->arch.vcore->dpdes field. Since this gets written by the guest
exit code, other VCPUs wishing to cause a doorbell interrupt don't
write that field directly, but instead set a vcpu->arch.doorbell_request
flag. This is consumed and set to 0 by the guest entry code, which
then sets DPDES to 1.
Emulating reads of the DPDES register is somewhat involved, because
it requires reading the doorbell pending interrupt status of all of the
VCPU threads in the virtual core, and if any of those VCPUs are
running, their doorbell status is only up-to-date in the hardware
DPDES registers of the CPUs where they are running. In order to get
a reasonable approximation of the current doorbell status, we send
those CPUs an IPI, causing an exit from the guest which will update
the vcpu->arch.vcore->dpdes field. We then use that value in
constructing the emulated DPDES register value.
Paul Mackerras [Mon, 6 Feb 2017 02:24:41 +0000 (13:24 +1100)]
KVM: PPC: Book3S HV: Allow userspace to set the desired SMT mode
This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core. Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering. This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core. With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.
On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore. On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Paul Mackerras [Wed, 15 Feb 2017 03:30:17 +0000 (14:30 +1100)]
KVM: PPC: Book3S HV: Context-switch HFSCR between host and guest on POWER9
This adds code to allow us to use a different value for the HFSCR
(Hypervisor Facilities Status and Control Register) when running the
guest from that which applies in the host. The reason for doing this
is to allow us to trap the msgsndp instruction and related operations
in future so that they can be virtualized. We also save the value of
HFSCR when a hypervisor facility unavailable interrupt occurs, because
the high byte of HFSCR indicates which facility the guest attempted to
access.
We save and restore the host value on guest entry/exit because some
bits of it affect host userspace execution.
We only do all this on POWER9, not on POWER8, because we are not
intending to virtualize any of the facilities controlled by HFSCR on
POWER8. In particular, the HFSCR bit that controls execution of
msgsndp and related operations does not exist on POWER8. The HFSCR
doesn't exist at all on POWER7.
Paul Mackerras [Fri, 19 May 2017 06:26:16 +0000 (16:26 +1000)]
KVM: PPC: Book3S HV: Don't let VCPU sleep if it has a doorbell pending
It is possible, through a narrow race condition, for a VCPU to exit
the guest with a H_CEDE hypercall while it has a doorbell interrupt
pending. In this case, the H_CEDE should return immediately, but in
fact it puts the VCPU to sleep until some other interrupt becomes
pending or a prod is received (via another VCPU doing H_PROD).
This fixes it by checking the DPDES (Directed Privileged Doorbell
Exception Status) bit for the thread along with the other interrupt
pending bits.
Paul Mackerras [Mon, 22 May 2017 06:55:16 +0000 (16:55 +1000)]
KVM: PPC: Book3S HV: Enable guests to use large decrementer mode on POWER9
This allows userspace (e.g. QEMU) to enable large decrementer mode for
the guest when running on a POWER9 host, by setting the LPCR_LD bit in
the guest LPCR value. With this, the guest exit code saves 64 bits of
the guest DEC value on exit. Other places that use the guest DEC
value check the LPCR_LD bit in the guest LPCR value, and if it is set,
omit the 32-bit sign extension that would otherwise be done.
This doesn't change the DEC emulation used by PR KVM because PR KVM
is not supported on POWER9 yet.
This is partly based on an earlier patch by Oliver O'Halloran.
Paul Mackerras [Tue, 6 Jun 2017 04:35:30 +0000 (14:35 +1000)]
KVM: PPC: Book3S HV: Ignore timebase offset on POWER9 DD1
POWER9 DD1 has an erratum where writing to the TBU40 register, which
is used to apply an offset to the timebase, can cause the timebase to
lose counts. This results in the timebase on some CPUs getting out of
sync with other CPUs, which then results in misbehaviour of the
timekeeping code.
To work around the problem, we make KVM ignore the timebase offset for
all guests on POWER9 DD1 machines. This means that live migration
cannot be supported on POWER9 DD1 machines.
Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Fri, 16 Jun 2017 01:53:19 +0000 (11:53 +1000)]
KVM: PPC: Book3S HV: Save/restore host values of debug registers
At present, HV KVM on POWER8 and POWER9 machines loses any instruction
or data breakpoint set in the host whenever a guest is run.
Instruction breakpoints are currently only used by xmon, but ptrace
and the perf_event subsystem can set data breakpoints as well as xmon.
To fix this, we save the host values of the debug registers (CIABR,
DAWR and DAWRX) before entering the guest and restore them on exit.
To provide space to save them in the stack frame, we expand the stack
frame allocated by kvmppc_hv_entry() from 112 to 144 bytes.
Fixes: ee15c8236741 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Cc: stable@vger.kernel.org # v3.14+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Thu, 15 Jun 2017 06:10:27 +0000 (16:10 +1000)]
KVM: PPC: Book3S HV: Preserve userspace HTM state properly
If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values. To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task. If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.
If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash. To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.
Fixes: ee15c8236741 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Cc: stable@vger.kernel.org # v3.14+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Thu, 15 Jun 2017 05:43:17 +0000 (15:43 +1000)]
KVM: PPC: Book3S HV: Restore critical SPRs to host values on guest exit
This restores several special-purpose registers (SPRs) to sane values
on guest exit that were missed before.
TAR and VRSAVE are readable and writable by userspace, and we need to
save and restore them to prevent the guest from potentially affecting
userspace execution (not that TAR or VRSAVE are used by any known
program that run uses the KVM_RUN ioctl). We save/restore these
in kvmppc_vcpu_run_hv() rather than on every guest entry/exit.
FSCR affects userspace execution in that it can prohibit access to
certain facilities by userspace. We restore it to the normal value
for the task on exit from the KVM_RUN ioctl.
IAMR is normally 0, and is restored to 0 on guest exit. However,
with a radix host on POWER9, it is set to a value that prevents the
kernel from executing user-accessible memory. On POWER9, we save
IAMR on guest entry and restore it on guest exit to the saved value
rather than 0. On POWER8 we continue to set it to 0 on guest exit.
PSPB is normally 0. We restore it to 0 on guest exit to prevent
userspace taking advantage of the guest having set it non-zero
(which would allow userspace to set its SMT priority to high).
UAMOR is normally 0. We restore it to 0 on guest exit to prevent
the AMR from being used as a covert channel between userspace
processes, since the AMR is not context-switched at present.
Fixes: ee15c8236741 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Cc: stable@vger.kernel.org # v3.14+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to save the values of three SPRs (special-purpose
registers) used by userspace to control event-based branches (EBBs),
which are essentially interrupts that get delivered directly to
userspace. These registers are loaded up with guest values when
entering the guest, and their values are saved when exiting the
guest, but we were not saving the host values and restoring them
before going back to userspace.
On POWER8 this would only affect userspace programs which explicitly
request the use of EBBs and also use the KVM_RUN ioctl, since the
only source of EBBs on POWER8 is the PMU, and there is an explicit
enable bit in the PMU registers (and those PMU registers do get
properly context-switched between host and guest). On POWER9 there
is provision for externally-generated EBBs, and these are not subject
to the control in the PMU registers.
Since these registers only affect userspace, we can save them when
we first come in from userspace and restore them before returning to
userspace, rather than saving/restoring the host values on every
guest entry/exit. Similarly, we don't need to worry about their
values on offline secondary threads since they execute in the context
of the idle task, which never executes in userspace.
Fixes: ee15c8236741 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Cc: stable@vger.kernel.org # v3.14+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Paul Mackerras [Mon, 22 May 2017 06:25:14 +0000 (16:25 +1000)]
KVM: PPC: Book3S HV: Cope with host using large decrementer mode
POWER9 introduces a new mode for the decrementer register, called
large decrementer mode, in which the decrementer counter is 56 bits
wide rather than 32, and reads are sign-extended rather than
zero-extended. For the decrementer, this new mode is optional and
controlled by a bit in the LPCR. The hypervisor decrementer (HDEC)
is 56 bits wide on POWER9 and has no mode control.
Since KVM code reads and writes the decrementer and hypervisor
decrementer registers in a few places, it needs to be aware of the
need to treat the decrementer value as a 64-bit quantity, and only do
a 32-bit sign extension when large decrementer mode is not in effect.
Similarly, the HDEC should always be treated as a 64-bit quantity on
POWER9. We define a new EXTEND_HDEC macro to encapsulate the feature
test for POWER9 and the sign extension.
To enable the sign extension to be removed in large decrementer mode,
we test the LPCR_LD bit in the host LPCR image stored in the struct
kvm for the guest. If is set then large decrementer mode is enabled
and the sign extension should be skipped.
This is partly based on an earlier patch by Oliver O'Halloran.
Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Linus Torvalds [Mon, 22 May 2017 01:26:54 +0000 (18:26 -0700)]
x86: fix 32-bit case of __get_user_asm_u64()
The code to fetch a 64-bit value from user space was entirely buggered,
and has been since the code was merged in early 2016 in commit 0c26098f9df7 ("x86/mm/32: Add support for 64-bit __get_user() on 32-bit
kernels").
Happily the buggered routine is almost certainly entirely unused, since
the normal way to access user space memory is just with the non-inlined
"get_user()", and the inlined version didn't even historically exist.
The normal "get_user()" case is handled by external hand-written asm in
arch/x86/lib/getuser.S that doesn't have either of these issues.
There were two independent bugs in __get_user_asm_u64():
- it still did the STAC/CLAC user space access marking, even though
that is now done by the wrapper macros, see commit 6cd7cf83460f
("x86: reorganize SMAP handling in user space accesses").
This didn't result in a semantic error, it just means that the
inlined optimized version was hugely less efficient than the
allegedly slower standard version, since the CLAC/STAC overhead is
quite high on modern Intel CPU's.
- the double register %eax/%edx was marked as an output, but the %eax
part of it was touched early in the asm, and could thus clobber other
inputs to the asm that gcc didn't expect it to touch.
In particular, that meant that the generated code could look like
this:
mov (%eax),%eax
mov 0x4(%eax),%edx
where the load of %edx obviously was _supposed_ to be from the 32-bit
word that followed the source of %eax, but because %eax was
overwritten by the first instruction, the source of %edx was
basically random garbage.
The fixes are trivial: remove the extraneous STAC/CLAC entries, and mark
the 64-bit output as early-clobber to let gcc know that no inputs should
alias with the output register.
Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: stable@kernel.org # v4.8+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 21 May 2017 22:25:46 +0000 (15:25 -0700)]
Clean up x86 unsafe_get/put_user() type handling
Al noticed that unsafe_put_user() had type problems, and fixed them in
commit 3faf66f46535 ("fix unsafe_put_user()"), which made me look more
at those functions.
It turns out that unsafe_get_user() had a type issue too: it limited the
largest size of the type it could handle to "unsigned long". Which is
fine with the current users, but doesn't match our existing normal
get_user() semantics, which can also handle "u64" even when that does
not fit in a long.
While at it, also clean up the type cast in unsafe_put_user(). We
actually want to just make it an assignment to the expected type of the
pointer, because we actually do want warnings from types that don't
convert silently. And it makes the code more readable by not having
that one very long and complex line.
[ This patch might become stable material if we ever end up back-porting
any new users of the unsafe uaccess code, but as things stand now this
doesn't matter for any current existing uses. ]
Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 21 May 2017 19:06:44 +0000 (12:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc uaccess fixes from Al Viro:
"Fix for unsafe_put_user() (no callers currently in mainline, but
anyone starting to use it will step into that) + alpha osf_wait4()
infoleak fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
osf_wait4(): fix infoleak
fix unsafe_put_user()
Linus Torvalds [Sun, 21 May 2017 18:52:00 +0000 (11:52 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single scheduler fix:
Prevent idle task from ever being preempted. That makes sure that
synchronize_rcu_tasks() which is ignoring idle task does not pretend
that no task is stuck in preempted state. If that happens and idle was
preempted on a ftrace trampoline the machine crashes due to
inconsistent state"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Call __schedule() from do_idle() without enabling preemption
Al Viro [Sun, 21 May 2017 17:08:42 +0000 (13:08 -0400)]
fix unsafe_put_user()
__put_user_size() relies upon its first argument having the same type as what
the second one points to; the only other user makes sure of that and
unsafe_put_user() should do the same.
Linus Torvalds [Sun, 21 May 2017 06:39:03 +0000 (23:39 -0700)]
Merge tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix a bug caused by not cleaning up the new instance unique triggers
when deleting an instance. It also creates a selftest that triggers
that bug.
- Fix the delayed optimization happening after kprobes boot up self
tests being removed by freeing of init memory.
- Comment kprobes on why the delay optimization is not a problem for
removal of modules, to keep other developers from searching that
riddle.
- Fix another case of rcu not watching in stack trace tracing.
* tag 'trace-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make sure RCU is watching before calling a stack trace
kprobes: Document how optimized kprobes are removed from module unload
selftests/ftrace: Add test to remove instance with active event triggers
selftests/ftrace: Fix bashisms
ftrace: Remove #ifdef from code and add clear_ftrace_function_probes() stub
ftrace/instances: Clear function triggers when removing instances
ftrace: Simplify glob handling in unregister_ftrace_function_probe_func()
tracing/kprobes: Enforce kprobes teardown after testing
tracing: Move postpone selftests to core from early_initcall
Linus Torvalds [Sat, 20 May 2017 23:12:30 +0000 (16:12 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this cycle.
- a pull request from Christoph for NVMe, which ended up being
manually applied to avoid pulling in newer bits in master. Mostly
fibre channel fixes from James, but also a few fixes from Jon and
Vijay
- a pull request from Konrad, with just a single fix for xen-blkback
from Gustavo.
- a fuseblk bdi fix from Jan, fixing a regression in this series with
the dynamic backing devices.
- a blktrace fix from Shaohua, replacing sscanf() with kstrtoull().
- a request leak fix for drbd from Lars, fixing a regression in the
last series with the kref changes. This will go to stable as well"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvmet: release the sq ref on rdma read errors
nvmet-fc: remove target cpu scheduling flag
nvme-fc: stop queues on error detection
nvme-fc: require target or discovery role for fc-nvme targets
nvme-fc: correct port role bits
nvme: unmap CMB and remove sysfs file in reset path
blktrace: fix integer parse
fuseblk: Fix warning in super_setup_bdi_name()
block: xen-blkback: add null check to avoid null pointer dereference
drbd: fix request leak introduced by locking/atomic, kref: Kill kref_sub()
Vijay Immanuel [Mon, 8 May 2017 23:38:35 +0000 (16:38 -0700)]
nvmet: release the sq ref on rdma read errors
On rdma read errors, release the sq ref that was taken
when the req was initialized. This avoids a hang in
nvmet_sq_destroy() when the queue is being freed.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
James Smart [Tue, 25 Apr 2017 22:32:01 +0000 (15:32 -0700)]
nvme-fc: stop queues on error detection
Per the recommendation by Sagi on:
http://lists.infradead.org/pipermail/linux-nvme/2017-April/009261.html
Rather than waiting for reset work thread to stop queues and abort the ios,
immediately stop the queues on error detection. Reset thread will restop
the queues (as it's called on other paths), but it does not appear to have
a side effect.
Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Jon Derrick [Fri, 5 May 2017 20:52:06 +0000 (14:52 -0600)]
nvme: unmap CMB and remove sysfs file in reset path
CMB doesn't get unmapped until removal while getting remapped on every
reset. Add the unmapping and sysfs file removal to the reset path in
nvme_pci_disable to match the mapping path in nvme_pci_enable.
Fixes: ef06ecc94 ("nvme : Add sysfs entry for NVMe CMBs when appropriate") Signed-off-by: Jon Derrick <jonathan.derrick@intel.com> Acked-by: Keith Busch <keith.busch@intel.com> Reviewed-By: Stephen Bates <sbates@raithlin.com> Cc: <stable@vger.kernel.org> # 4.9+ Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Sat, 20 May 2017 16:02:27 +0000 (09:02 -0700)]
Merge tag 'staging-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a number of staging driver fixes for 4.12-rc2
Most of them are typec driver fixes found by reviewers and users of
the code. There are also some removals of files no longer needed in
the tree due to the ion driver rewrite in 4.12-rc1, as well as some
wifi driver fixes. And to round it out, a MAINTAINERS file update.
All have been in linux-next with no reported issues"
* tag 'staging-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (22 commits)
MAINTAINERS: greybus-dev list is members-only
staging: fsl-dpaa2/eth: add ETHERNET dependency
staging: typec: fusb302: refactor resume retry mechanism
staging: typec: fusb302: reset i2c_busy state in error
staging: rtl8723bs: remove re-positioned call to kfree in os_dep/ioctl_cfg80211.c
staging: rtl8192e: GetTs Fix invalid TID 7 warning.
staging: rtl8192e: rtl92e_get_eeprom_size Fix read size of EPROM_CMD.
staging: rtl8192e: fix 2 byte alignment of register BSSIDR.
staging: rtl8192e: rtl92e_fill_tx_desc fix write to mapped out memory.
staging: vc04_services: Fix bulk cache maintenance
staging: ccree: remove extraneous spin_unlock_bh() in error handler
staging: typec: Fix sparse warnings about incorrect types
staging: typec: fusb302: do not free gpio from managed resource
staging: typec: tcpm: Fix Port Power Role field in PS_RDY messages
staging: typec: tcpm: Respond to Discover Identity commands
staging: typec: tcpm: Set correct flags in PD request messages
staging: typec: tcpm: Drop duplicate PD messages
staging: typec: fusb302: Fix chip->vbus_present init value
staging: typec: fusb302: Fix module autoload
staging: typec: tcpci: declare private structure as static
...
Linus Torvalds [Sat, 20 May 2017 15:52:34 +0000 (08:52 -0700)]
Merge tag 'usb-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.12-rc2
Most of them come from Johan, in his valiant quest to fix up all
drivers that could be affected by "malicious" USB devices. There's
also some fixes for more "obscure" drivers to handle some of the
vmalloc stack fallout (which for USB drivers, was always the case, but
very few people actually ran those systems...)
Other than that, the normal set of xhci and gadget and musb driver
fixes as well.
All have been in linux-next with no reported issues"
* tag 'usb-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: musb: tusb6010_omap: Do not reset the other direction's packet size
usb: musb: Fix trying to suspend while active for OTG configurations
usb: host: xhci-plat: propagate return value of platform_get_irq()
xhci: Fix command ring stop regression in 4.11
xhci: remove GFP_DMA flag from allocation
USB: xhci: fix lock-inversion problem
usb: host: xhci-ring: don't need to clear interrupt pending for MSI enabled hcd
usb: host: xhci-mem: allocate zeroed Scratchpad Buffer
xhci: apply PME_STUCK_QUIRK and MISSING_CAS quirk for Denverton
usb: xhci: trace URB before giving it back instead of after
USB: serial: qcserial: add more Lenovo EM74xx device IDs
USB: host: xhci: use max-port define
USB: hub: fix SS max number of ports
USB: hub: fix non-SS hub-descriptor handling
USB: hub: fix SS hub-descriptor handling
USB: usbip: fix nonconforming hub descriptor
USB: gadget: dummy_hcd: fix hub-descriptor removable fields
doc-rst: fixed kernel-doc directives in usb/typec.rst
USB: core: of: document reference taken by companion helper
USB: ehci-platform: fix companion-device leak
...
Linus Torvalds [Sat, 20 May 2017 15:44:22 +0000 (08:44 -0700)]
Merge tag 'char-misc-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are five small bugfixes for reported issues with 4.12-rc1 and
earlier kernels. Nothing huge here, just a lp, mem, vpd, and uio
driver fix, along with a Kconfig fixup for one of the misc drivers.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
firmware: Google VPD: Fix memory allocation error handling
drivers: char: mem: Check for address space wraparound with mmap()
uio: fix incorrect memory leak cleanup
misc: pci_endpoint_test: select CRC32
char: lp: fix possible integer overflow in lp_setup()
Linus Torvalds [Sat, 20 May 2017 15:35:27 +0000 (08:35 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- orion_wdt compile-test dependencies
- sama5d4_wdt: WDDIS handling and a race confition
- pcwd_usb: fix NULL-deref at probe
- cadence_wdt: fix timeout setting
- wdt_pci: fix build error if SOFTWARE_REBOOT is defined
- iTCO_wdt: all versions count down twice
- zx2967: remove redundant dev_err call in zx2967_wdt_probe()
- bcm281xx: Fix use of uninitialized spinlock
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: bcm281xx: Fix use of uninitialized spinlock.
watchdog: zx2967: remove redundant dev_err call in zx2967_wdt_probe()
iTCO_wdt: all versions count down twice
watchdog: wdt_pci: fix build error if define SOFTWARE_REBOOT
watchdog: cadence_wdt: fix timeout setting
watchdog: pcwd_usb: fix NULL-deref at probe
watchdog: sama5d4: fix race condition
watchdog: sama5d4: fix WDDIS handling
watchdog: orion: fix compile-test dependencies
Linus Torvalds [Sat, 20 May 2017 15:29:30 +0000 (08:29 -0700)]
Merge tag 'drm-fixes-for-v4.12-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Mostly nouveau and i915, fairly quiet as usual for rc2"
* tag 'drm-fixes-for-v4.12-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/atmel-hlcdc: Fix output initialization
gpu: host1x: select IOMMU_IOVA
drm/nouveau/fifo/gk104-: Silence a locking warning
drm/nouveau/secboot: plug memory leak in ls_ucode_img_load_gr() error path
drm/nouveau: Fix drm poll_helper handling
drm/i915: don't do allocate_va_range again on PIN_UPDATE
drm/i915: Fix rawclk readout for g4x
drm/i915: Fix runtime PM for LPE audio
drm/i915/glk: Fix DSI "*ERROR* ULPS is still active" messages
drm/i915/gvt: avoid unnecessary vgpu switch
drm/i915/gvt: not to restore in-context mmio
drm/etnaviv: don't put fence in case of submit failure
drm/i915/gvt: fix typo: "supporte" -> "support"
drm: hdlcd: Fix the calculation of the scanout start address
Linus Torvalds [Sat, 20 May 2017 00:46:51 +0000 (17:46 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the first sweep of mostly minor fixes. There's one security
one: the read past the end of a buffer in qedf, and a panic fix for
lpfc SLI-3 adapters, but the rest are a set of include and build
dependency tidy ups and assorted other small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pmcraid: remove redundant check to see if request_size is less than zero
scsi: lpfc: ensure els_wq is being checked before destroying it
scsi: cxlflash: Select IRQ_POLL
scsi: qedf: Avoid reading past end of buffer
scsi: qedf: Cleanup the type of io_log->op
scsi: lpfc: double lock typo in lpfc_ns_rsp()
scsi: qedf: properly update arguments position in function call
scsi: scsi_lib: Add #include <scsi/scsi_transport.h>
scsi: MAINTAINERS: update OSD entries
scsi: Skip deleted devices in __scsi_device_lookup
scsi: lpfc: Fix panic on BFS configuration
scsi: libfc: do not flood console with messages 'libfc: queue full ...'
Linus Torvalds [Sat, 20 May 2017 00:35:34 +0000 (17:35 -0700)]
Merge branch 'libnvdimm-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A couple of compile fixes.
With the removal of the ->direct_access() method from
block_device_operations in favor of a new dax_device + dax_operations
we broke two configurations.
The CONFIG_BLOCK=n case is fixed by compiling out the block+dax
helpers in the dax core. Configurations with FS_DAX=n EXT4=y / XFS=y
and DAX=m fail due to the helpers the builtin filesystem needs being
in a module, so we stub out the helpers in the FS_DAX=n case."
* 'libnvdimm-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax, xfs, ext4: compile out iomap-dax paths in the FS_DAX=n case
dax: fix false CONFIG_BLOCK dependency
Linus Torvalds [Sat, 20 May 2017 00:27:28 +0000 (17:27 -0700)]
Merge tag 'iommu-fixes-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- another compile-fix as a fallout of the recent header-file cleanup
- add a missing IO/TLB flush to the Intel VT-d kdump code path
- a fix for ARM64 dma code to only access initialized iova_domain
members
* tag 'iommu-fixes-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/mediatek: Include linux/dma-mapping.h
iommu/vt-d: Flush the IOTLB to get rid of the initial kdump mappings
iommu/dma: Don't touch invalid iova_domain members
Linus Torvalds [Fri, 19 May 2017 22:13:13 +0000 (15:13 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- a fix for a build failure introduced in -rc1 when tracepoints are
enabled on 32-bit ARM.
- disable use of stack pointer protection in the hyp code which can
cause panics.
- a handful of VGIC fixes.
- a fix to the init of the redistributors on GICv3 systems that
prevented boot with kvmtool on GICv3 systems introduced in -rc1.
- a number of race conditions fixed in our MMU handling code.
- a fix for the guest being able to program the debug extensions for
the host on the 32-bit side.
PPC:
- fixes for build failures with PR KVM configurations.
- a fix for a host crash that can occur on POWER9 with radix guests.
x86:
- fixes for nested PML and nested EPT.
- a fix for crashes caused by reserved bits in SSE MXCSR that could
have been set by userspace.
- an optimization of halt polling that fixes high CPU overhead.
- fixes for four reports from Dan Carpenter's static checker.
- a protection around code that shouldn't have been preemptible.
- a fix for port IO emulation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (27 commits)
KVM: x86: prevent uninitialized variable warning in check_svme()
KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh()
KVM: x86: zero base3 of unusable segments
KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation
KVM: x86: Fix potential preemption when get the current kvmclock timestamp
KVM: Silence underflow warning in avic_get_physical_id_entry()
KVM: arm/arm64: Hold slots_lock when unregistering kvm io bus devices
KVM: arm/arm64: Fix bug when registering redist iodevs
KVM: x86: lower default for halt_poll_ns
kvm: arm/arm64: Fix use after free of stage2 page table
kvm: arm/arm64: Force reading uncached stage2 PGD
KVM: nVMX: fix EPT permissions as reported in exit qualification
KVM: VMX: Don't enable EPT A/D feature if EPT feature is disabled
KVM: x86: Fix load damaged SSEx MXCSR register
kvm: nVMX: off by one in vmx_write_pml_buffer()
KVM: arm: rename pm_fake handler to trap_raz_wi
KVM: arm: plug potential guest hardware debug leakage
kvm: arm/arm64: Fix race in resetting stage2 PGD
KVM: arm/arm64: vgic-v3: Use PREbits to infer the number of ICH_APxRn_EL2 registers
KVM: arm/arm64: vgic-v3: Do not use Active+Pending state for a HW interrupt
...
Linus Torvalds [Fri, 19 May 2017 22:06:48 +0000 (15:06 -0700)]
Merge tag 'for-linus-4.12b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Some fixes for the new Xen 9pfs frontend and some minor cleanups"
* tag 'for-linus-4.12b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make xen_flush_tlb_all() static
xen: cleanup pvh leftovers from pv-only sources
xen/9pfs: p9_trans_xen_init and p9_trans_xen_exit can be static
xen/9pfs: fix return value check in xen_9pfs_front_probe()
Linus Torvalds [Fri, 19 May 2017 20:36:56 +0000 (13:36 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We had a small batch of fixes before -rc1, but here is a larger one.
It contains a backmerge of 4.12-rc1 since some of the downstream
branches we merge had that as base; at the same time we already had
merged contents before -rc1 and rebase wasn't the right solution.
A mix of random smaller fixes and a few things worth pointing out:
- We've started telling people to avoid cross-tree shared branches if
all they're doing is picking up one or two DT-used constants from a
shared include file, and instead to use the numeric values on first
submission. Follow-up moving over to symbolic names are sent in
right after -rc1, i.e. here. It's only a few minor patches of this
type.
- Linus Walleij and others are resurrecting the 'Gemini' platform,
and wanted a cut-down platform-specific defconfig for it. So I
picked that up for them.
- Rob Herring ran 'savedefconfig' on arm64, it's a bit churny but it
helps people to prepare patches since it's a pain when defconfig
and current savedefconfig contents differs too much.
- Devicetree additions for some pinctrl drivers for Armada that were
merged this window. I'd have preferred to see those earlier but
it's not a huge deail.
The biggest change worth pointing out though since it's touching other
parts of the tree: We added prefixes to be used when cross-including
DT contents between arm64 and arm, allowing someone to #include
<arm/foo.dtsi> from arm64, and likewise. As part of that, we needed
arm/foo.dtsi to work on arm as well. The way I suggested this to Heiko
resulted in a recursive symlink.
Instead, I've now moved it out of arch/*/boot/dts/include, into a
shared location under scripts/dtc. While I was at it, I consolidated
so all architectures now behave the same way in this manner.
Rob Herring (DT maintainer) has acked it. I cc:d most other arch
maintainers but nobody seems to care much; it doesn't really affect
them since functionality is unchanged for them by default"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
arm64: dts: rockchip: fix include reference
firmware: ti_sci: fix strncat length check
ARM: remove duplicate 'const' annotations'
arm64: defconfig: enable options needed for QCom DB410c board
arm64: defconfig: sync with savedefconfig
ARM: configs: add a gemini defconfig
devicetree: Move include prefixes from arch to separate directory
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
soc: bcm: brcmstb: Correctly match 7435 SoC
tee: add ARM_SMCCC dependency
ARM: omap2+: make omap4_get_cpu1_ns_pa_addr declaration usable
ARM64: dts: mediatek: configure some fixed mmc parameters
...
Linus Torvalds [Fri, 19 May 2017 20:34:34 +0000 (13:34 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes/cleanups from Catalin Marinas:
- Avoid taking a mutex in the secondary CPU bring-up path when
interrupts are disabled
- Ignore perf exclude_hv when the kernel is running in Hyp mode
- Remove redundant instruction in cmpxchg
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/cpufeature: don't use mutex in bringup path
arm64: perf: Ignore exclude_hv when kernel is running in HYP
arm64: Remove redundant mov from LL/SC cmpxchg
Linus Torvalds [Fri, 19 May 2017 18:31:38 +0000 (11:31 -0700)]
Merge tag 'powerpc-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The headliner is a fix for FP/VMX register corruption when using
transactional memory, and a new selftest to go with it.
Then there's the virt_addr_valid() fix, currently HARDENDED_USERCOPY
is tripping on that causing some machines to crash.
A few other fairly minor fixes for long tail things, and a couple of
fixes for code we just merged.
Thanks to: Breno Leitao, Gautham Shenoy, Michael Neuling, Naveen Rao.
Nicholas Piggin, Paul Mackerras"
* tag 'powerpc-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix virt_addr_valid() etc. on 64-bit hash
powerpc/mm: Fix crash in page table dump with huge pages
powerpc/kprobes: Fix handling of instruction emulation on probe re-entry
powerpc/powernv: Set NAPSTATELOST after recovering paca on P9 DD1
selftests/powerpc: Test TM and VMX register state
powerpc/tm: Fix FP and VMX register corruption
powerpc/modules: If mprofile-kernel is enabled add it to vermagic
Radim Krčmář [Thu, 18 May 2017 17:37:31 +0000 (19:37 +0200)]
KVM: x86/vPMU: fix undefined shift in intel_pmu_refresh()
Static analysis noticed that pmu->nr_arch_gp_counters can be 32
(INTEL_PMC_MAX_GENERIC) and therefore cannot be used to shift 'int'.
I didn't add BUILD_BUG_ON for it as we have a better checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 2dd01dcc98f6 ("KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch") Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Radim Krčmář [Thu, 18 May 2017 17:37:30 +0000 (19:37 +0200)]
KVM: x86: zero base3 of unusable segments
Static checker noticed that base3 could be used uninitialized if the
segment was not present (useable). Random stack values probably would
not pass VMCS entry checks.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 9e17427875c9 ("KVM: x86 emulator: consolidate segment accessors") Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Wanpeng Li [Fri, 19 May 2017 09:46:56 +0000 (02:46 -0700)]
KVM: X86: Fix read out-of-bounds vulnerability in kvm pio emulation
Huawei folks reported a read out-of-bounds vulnerability in kvm pio emulation.
- "inb" instruction to access PIT Mod/Command register (ioport 0x43, write only,
a read should be ignored) in guest can get a random number.
- "rep insb" instruction to access PIT register port 0x43 can control memcpy()
in emulator_pio_in_emulated() to copy max 0x400 bytes but only read 1 bytes,
which will disclose the unimportant kernel memory in host but no crash.
The similar test program below can reproduce the read out-of-bounds vulnerability:
void hexdump(void *mem, unsigned int len)
{
unsigned int i, j;
The vcpu->arch.pio_data buffer is used by both in/out instrutions emulation
w/o clear after using which results in some random datas are left over in
the buffer. Guest reads port 0x43 will be ignored since it is write only,
however, the function kernel_pio() can't distigush this ignore from successfully
reads data from device's ioport. There is no new data fill the buffer from
port 0x43, however, emulator_pio_in_emulated() will copy the stale data in
the buffer to the guest unconditionally. This patch fixes it by clearing the
buffer before in instruction emulation to avoid to grant guest the stale data
in the buffer.
In addition, string I/O is not supported for in kernel device. So there is no
iteration to read ioport %RCX times for string I/O. The function kernel_pio()
just reads one round, and then copy the io size * %RCX to the guest unconditionally,
actually it copies the one round ioport data w/ other random datas which are left
over in the vcpu->arch.pio_data buffer to the guest. This patch fixes it by
introducing the string I/O support for in kernel device in order to grant the right
ioport datas to the guest.
Before the patch:
0x000000: fe 38 93 93 ff ff ab ab .8......
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
0x000000: f6 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 4d 51 30 30 ....MQ00
0x000018: 30 30 20 33 20 20 20 20 00 3
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
After the patch:
0x000000: 1e 02 f8 00 ff ff ab ab ........
0x000008: ab ab ab ab ab ab ab ab ........
0x000010: ab ab ab ab ab ab ab ab ........
0x000018: ab ab ab ab ab ab ab ab ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
0x000000: d2 e2 d2 df d2 db d2 d7 ........
0x000008: d2 d3 d2 cf d2 cb d2 c7 ........
0x000010: d2 c4 d2 c0 d2 bc d2 b8 ........
0x000018: d2 b4 d2 b0 d2 ac d2 a8 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
0x000000: 00 00 00 00 00 00 00 00 ........
0x000008: 00 00 00 00 00 00 00 00 ........
0x000010: 00 00 00 00 00 00 00 00 ........
0x000018: 00 00 00 00 00 00 00 00 ........
0x000020: ab ab ab ab ab ab ab ab ........
0x000028: ab ab ab ab ab ab ab ab ........
0x000030: ab ab ab ab ab ab ab ab ........
0x000038: ab ab ab ab ab ab ab ab ........
This can be reproduced by run kvm-unit-tests/hyperv_stimer.flat w/
CONFIG_PREEMPT and CONFIG_DEBUG_PREEMPT enabled.
Safe access to per-CPU data requires a couple of constraints, though: the
thread working with the data cannot be preempted and it cannot be migrated
while it manipulates per-CPU variables. If the thread is preempted, the
thread that replaces it could try to work with the same variables; migration
to another CPU could also cause confusion. However there is no preemption
disable when reads host per-CPU tsc rate to calculate the current kvmclock
timestamp.
This patch fixes it by utilizing get_cpu/put_cpu pair to guarantee both
__this_cpu_read() and rdtsc() are not preempted.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Shaohua Li [Fri, 19 May 2017 15:04:59 +0000 (08:04 -0700)]
blktrace: fix integer parse
sscanf is a very poor way to parse integer. For example, I input
"discard" for act_mask, it gets 0xd and completely messes up. Using
correct API to do integer parse.
This patch also makes attributes accept any base of integer.
Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Ard Biesheuvel [Fri, 19 May 2017 08:56:40 +0000 (09:56 +0100)]
i2c: designware: don't infer timings described by ACPI from clock rate
Commit 372205e6212f1 ("i2c: designware: Get selected speed mode
sda-hold-time via ACPI") updated the logic that reads the timing
parameters for various I2C bus rates from the DSDT, to only read
the timing parameters for the currently selected mode.
This causes a WARN_ON() splat on platforms that legally omit the clock
frequency from the ACPI description, because in the new situation, the
core I2C designware driver still accesses the fields in the driver
struct that we no longer populate, and proceeds to calculate them from
the clock frequency. Since the clock frequency is unspecified, the
driver complains loudly using a WARN_ON().
So revert back to the old situation, where the struct fields for all
timings are populated, but retain the new logic which chooses the SDA
hold time from the timing mode that is currently in use.
Fixes: 372205e6212f1 ("i2c: designware: Get selected speed mode ...") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Paolo Bonzini [Wed, 5 Apr 2017 11:41:15 +0000 (13:41 +0200)]
iTCO_wdt: all versions count down twice
The ICH9 is listed as having TCO v2, and indeed the behavior in the
datasheet corresponds to v2 (for example the NO_REBOOT flag is
accessible via the 16KiB-aligned Root Complex Base Address).
However, the TCO counts twice just like in v1; the documentation
of the SECOND_TO_STS bit says: "ICH9 sets this bit to 1 to indicate
that the TIMEOUT bit had been (or is currently) set and a second
timeout occurred before the TCO_RLD register was written. If this
bit is set and the NO_REBOOT config bit is 0, then the ICH9 will
reboot the system after the second timeout. The same can be found
in the BayTrail (Atom E3800) datasheet, and even HOWTOs around
the Internet say that it will reboot after _twice_ the specified
heartbeat.
I did not find the Apollo Lake datasheet, but because v4/v5 has
a SECOND_TO_STS bit just like the previous version I'm enabling
this for Apollo Lake as well.
Cc: linux-watchdog@vger.kernel.org Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Arnd Bergmann [Wed, 11 Jan 2017 11:53:05 +0000 (12:53 +0100)]
firmware: ti_sci: fix strncat length check
gcc-7 notices that the length we pass to strncat is wrong:
drivers/firmware/ti_sci.c: In function 'ti_sci_probe':
drivers/firmware/ti_sci.c:204:32: error: specified bound 50 equals the size of the destination [-Werror=stringop-overflow=]
Instead of the total length, we must pass the length of the
remaining space here.
Fixes: 222f81aabd34 ("firmware: Add basic support for TI System Control Interface (TI-SCI) protocol") Cc: stable@vger.kernel.org Acked-by: Nishanth Menon <nm@ti.com> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 'usb-serial-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc2
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Olof Johansson [Fri, 19 May 2017 07:02:16 +0000 (00:02 -0700)]
Merge tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.12-rc cycle most consisting of few minor dts fixes
for various devices. Also included is a memory controller (GPMC) debug output
fix as without that the shown bootloader configured GPMC bus width will
be wrong and won't work for kernel timings:
- Add dra7 powerhold configuration to be able to shut down pmic correctly
- Fix polarity for gta04 mcbsp4 clocks for modem
- Fix Pandaboard CEC pin pull making it usable
- Fix LogicPD Torpedo camera pin mux
- Fix GPMC debug bus width
- Reduce cpu thermal shutdown temperature
* tag 'omap-for-v4.12/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: Reduce cpu thermal shutdown temperature
memory: omap-gpmc: Fix debug output for access width
ARM: dts: LogicPD Torpedo: Fix camera pin mux
ARM: dts: omap4: enable CEC pin for Pandaboard A4 and ES
ARM: dts: gta04: fix polarity of clocks for mcbsp4
ARM: dts: dra7: Add power hold and power controller properties to palmas
Olof Johansson [Fri, 19 May 2017 07:02:04 +0000 (00:02 -0700)]
Merge tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.12:
- A fix on GPCv2 power domain driver Kconfig which causes a build
failure when CONFIG_PM is not set.
- Pull down PMIC IRQ pin for imx53-qsrb board to prevent spurious
PMIC interrupts from happening.
- Remove board level OPP override for imx6sx-sdb to fix a boot crash
seen on Rev.C boards.
* tag 'imx-fixes-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: add PM dependency for IMX7_PM_DOMAINS
ARM: dts: imx6sx-sdb: Remove OPP override
ARM: dts: imx53-qsrb: Pulldown PMIC IRQ pin
Rob Herring [Wed, 17 May 2017 21:52:30 +0000 (16:52 -0500)]
arm64: defconfig: enable options needed for QCom DB410c board
Enable Qualcomm drivers needed to boot Dragonboard 410c with HDMI. This
enables support for clocks, regulators, and USB PHY.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org>
[Olof: Turned off _RPM configs per follow-up email] Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Sun, 14 May 2017 21:45:02 +0000 (23:45 +0200)]
ARM: configs: add a gemini defconfig
It makes sense to have a stripped-down defconfig for just Gemini, as
it is a pretty small platform used in NAS etc, and will use appended
device tree. It is also quick to compile and test. Hopefully this
defconfig can be a good base for distributions such as OpenWRT.
I plan to add in the config options needed for the different
variants of Gemini as we go along.
Cc: Janos Laube <janos.dev@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 19 May 2017 06:55:53 +0000 (23:55 -0700)]
Merge tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
4.12, please pull the following:
- Baruch provides several fixes for the Raspberry Pi (BCM2835) Device
Tree source include file: uart0 pinctrl node names, pin number for
i2c0, uart0 rts/cts pins and invalid uart1 pin, missing numbers for
ethernet aliases
* tag 'arm-soc/for-4.12/devicetree-fixes' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm2835: add index to the ethernet alias
ARM: dts: bcm2835: fix uart0/uart1 pins
ARM: dts: bcm2835: fix i2c0 pins
ARM: dts: bcm2835: fix uart0 pinctrl node names
Olof Johansson [Sat, 13 May 2017 03:13:26 +0000 (20:13 -0700)]
devicetree: Move include prefixes from arch to separate directory
We use a directory under arch/$ARCH/boot/dts as an include path
that has links outside of the subtree to find dt-bindings from under
include/dt-bindings. That's been working well, but new DT architectures
haven't been adding them by default.
Recently there's been a desire to share some of the DT material between
arm and arm64, which originally caused developers to create symlinks or
relative includes between the subtrees. This isn't ideal -- it breaks
if the DT files aren't stored in the exact same hierarchy as the kernel
tree, and generally it's just icky.
As a somewhat cleaner solution we decided to add a $ARCH/ prefix link
once, and allow DTS files to reference dtsi (and dts) files in other
architectures that way.
Original approach was to create these links under each architecture,
but it lead to the problem of recursive symlinks.
As a remedy, move the include link directories out of the architecture
trees into a common location. At the same time, they can now share one
directory and one dt-bindings/ link as well.
Fixes: 00da6bd31299 ('ARM: dts: add arm/arm64 include symlinks') Reported-by: Russell King <linux@armlinux.org.uk> Reported-by: Omar Sandoval <osandov@osandov.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Rob Herring <robh@kernel.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Frank Rowand <frowand.list@gmail.com> Cc: linux-arch <linux-arch@vger.kernel.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 19 May 2017 06:54:47 +0000 (23:54 -0700)]
Merge tag 'v4.12-rc1' into fixes
We've received a few fixes branches with -rc1 as base, but our contents was
still at pre-rc1. Merge it in expliticly to make 'git merge --log' clear on
hat was actually merged.
Michael Ellerman [Thu, 18 May 2017 10:37:31 +0000 (20:37 +1000)]
powerpc/mm: Fix virt_addr_valid() etc. on 64-bit hash
virt_addr_valid() is supposed to tell you if it's OK to call virt_to_page() on
an address. What this means in practice is that it should only return true for
addresses in the linear mapping which are backed by a valid PFN.
We are failing to properly check that the address is in the linear mapping,
because virt_to_pfn() will return a valid looking PFN for more or less any
address. That bug is actually caused by __pa(), used in virt_to_pfn().
This started happening after commit 7ba08200c956 ("powerpc: Work around gcc
miscompilation of __pa() on 64-bit") (Aug 2013), where we changed the definition
of __pa() to work around a GCC bug. Prior to that we subtracted PAGE_OFFSET from
the value passed to __pa(), meaning __pa() of a 0xd or 0x0 address would give
you something bogus back.
Until we can verify if that GCC bug is no longer an issue, or come up with
another solution, this commit does the minimal fix to make virt_addr_valid()
work, by explicitly checking that the address is in the linear mapping region.
Fixes: 7ba08200c956 ("powerpc: Work around gcc miscompilation of __pa() on 64-bit") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Balbir Singh <bsingharora@gmail.com> Tested-by: Breno Leitao <breno.leitao@gmail.com>
Dave Airlie [Fri, 19 May 2017 00:23:14 +0000 (10:23 +1000)]
Merge tag 'drm-intel-fixes-2017-05-18-1' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.12-rc2
* tag 'drm-intel-fixes-2017-05-18-1' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: don't do allocate_va_range again on PIN_UPDATE
drm/i915: Fix rawclk readout for g4x
drm/i915: Fix runtime PM for LPE audio
drm/i915/glk: Fix DSI "*ERROR* ULPS is still active" messages
drm/i915/gvt: avoid unnecessary vgpu switch
drm/i915/gvt: not to restore in-context mmio
drm/i915/gvt: fix typo: "supporte" -> "support"
Dave Airlie [Fri, 19 May 2017 00:20:53 +0000 (10:20 +1000)]
Merge tag 'drm-misc-fixes-2017-05-18' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- host1x: Fix link error when host1x is built-in and iova is a module (Arnd)
- hlcdc: Fix arguments passed to drm_of_find_panel_or_bridge (Boris)
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
* tag 'drm-misc-fixes-2017-05-18' of git://anongit.freedesktop.org/git/drm-misc:
drm/atmel-hlcdc: Fix output initialization
gpu: host1x: select IOMMU_IOVA
Linus Torvalds [Thu, 18 May 2017 19:04:41 +0000 (12:04 -0700)]
Merge tag 'md/4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
- Several bug fixes for raid5-cache from Song Liu, mainly handle
journal disk error
- Fix bad block handling in choosing raid1 disk from Tomasz Majchrzak
- Simplify external metadata array sysfs handling from Artur
Paszkiewicz
- Optimize raid0 discard handling from me, now raid0 will dispatch
large discard IO directly to underlayer disks.
* tag 'md/4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid1: prefer disk without bad blocks
md/r5cache: handle sync with data in write back cache
md/r5cache: gracefully handle journal device errors for writeback mode
md/raid1/10: avoid unnecessary locking
md/raid5-cache: in r5l_do_submit_io(), submit io->split_bio first
md/md0: optimize raid0 discard handling
md: don't return -EAGAIN in md_allow_write for external metadata arrays
md/raid5: make use of spin_lock_irq over local_irq_disable + spin_lock
Wei Yongjun [Thu, 18 May 2017 15:22:41 +0000 (15:22 +0000)]
xen/9pfs: p9_trans_xen_init and p9_trans_xen_exit can be static
Fixes the following sparse warnings:
net/9p/trans_xen.c:528:5: warning:
symbol 'p9_trans_xen_init' was not declared. Should it be static?
net/9p/trans_xen.c:540:6: warning:
symbol 'p9_trans_xen_exit' was not declared. Should it be static?
Wei Yongjun [Tue, 16 May 2017 14:22:47 +0000 (14:22 +0000)]
xen/9pfs: fix return value check in xen_9pfs_front_probe()
In case of error, the function xenbus_read() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: e01cba69d3a9 ("xen/9pfs: connect to the backend") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
Linus Torvalds [Thu, 18 May 2017 18:17:34 +0000 (11:17 -0700)]
Merge tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fix from Masahiro Yamada:
"Fix headers_install to not delete pre-existing headers in the install
destination"
* tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: skip install/check of headers right under uapi directories
Linus Torvalds [Thu, 18 May 2017 17:04:42 +0000 (10:04 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
watchdog: wdt_pci: fix build error if define SOFTWARE_REBOOT
To fix following build error when SOFTWARE_REBOOT is defined:
CC [M] driver/watchdog/wdt_pci.o
driver/watchdog/wdt_pci.c: In function 'wdtpci_interrupt':
driver/watchdog/wdt_pci.c:335:3: error: too many arguments to function 'emergency_restart'
emergency_restart(NULL);
^
In file included from driver/watchdog/wdt_pci.c:51:0:
include/linux/reboot.h:80:13: note: declared here
extern void emergency_restart(void);
^
WDT_MR and WDT_CR must not updated within three slow clock periods after
the last ping (write to WDT_CR or WDT_MR). Ensure enough time has elapsed
before writing those registers.
wdt_write() waits for 4 periods to ensure at least 3 edges are seen by the
IP.
The datasheet states: "When setting the WDDIS bit, and while it is set, the
fields WDV and WDD must not be modified."
Because the whole configuration is already cached inside .mr, wait for the
user to enable the watchdog to configure it so it is enabled and configured
at the same time (what the IP is actually expecting).
When the watchdog is already enabled, it is not an issue to reconfigure it.
Arnd Bergmann [Thu, 2 Mar 2017 12:09:52 +0000 (13:09 +0100)]
watchdog: orion: fix compile-test dependencies
I ran into one corner case with the orion watchdog using the
atomic_io_modify interface:
drivers/watchdog/orion_wdt.o: In function `orion_stop':
orion_wdt.c:(.text.orion_stop+0x28): undefined reference to `atomic_io_modify'
drivers/watchdog/orion_wdt.o: In function `armada375_stop':
orion_wdt.c:(.text.armada375_stop+0x28): undefined reference to `atomic_io_modify'
This function is available on all 32-bit ARM builds except for ebsa110, so
we have to specifically exclude that from compile-testing.
Fixes: 334d1fb69091 ("watchdog: Enable COMPILE_TEST where possible") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Thu, 18 May 2017 16:38:09 +0000 (09:38 -0700)]
Merge tag 'hwmon-for-linus-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix problem with hotplug state machine in coretemp driver"
* tag 'hwmon-for-linus-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Handle frozen hotplug state correctly
Ido Schimmel [Thu, 18 May 2017 11:03:52 +0000 (13:03 +0200)]
mlxsw: spectrum: Avoid possible NULL pointer dereference
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes: b2bbdc6ced1f ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth: Do not print an error message for probe deferral
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth: Use platform device for printing before register_netdev()
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: abb233ca743d587d ("sh_eth: Register MDIO bus before registering the network device") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: David S. Miller <davem@davemloft.net>
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes: 12cbf82736b6 ("mlxsw: spectrum: Support for counters on router interfaces") Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
firmware: Google VPD: Fix memory allocation error handling
This patch fixes several issues:
- if the 1st 'kzalloc' fails, we dereference a NULL pointer
- if the 2nd 'kzalloc' fails, there is a memory leak
- if 'sysfs_create_bin_file' fails there is also a memory leak
Fix it by adding a test after the first memory allocation and some error
handling paths to correctly free memory if needed.
Boris Brezillon [Thu, 18 May 2017 12:35:21 +0000 (14:35 +0200)]
drm/atmel-hlcdc: Fix output initialization
drm_of_find_panel_or_bridge() is expecting np to point to the encoder
node, not the bridge or panel this encoder is feeding.
Moreover, the endpoint parameter passed to drm_of_find_panel_or_bridge()
is always set to zero, which prevents us from probing all outputs.
We also move the atmel_hlcdc_rgb_output allocation after the
panel/bridge detection to avoid useless allocations.
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Fixes: 5d14619f84c0 ("drm: convert drivers to use drm_of_find_panel_or_bridge") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/1495110921-4032-1-git-send-email-boris.brezillon@free-electrons.com
projects / kernel.git / log