The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Match the data type of a temporary holding a reference to the FIFO port
with the type of the original reference coming from `struct parport',
avoiding data truncation with LP64 ports such as SPARC64 that refer to
PCI port I/O locations via their corresponding MMIO addresses and will
therefore have non-zero bits in the high 32-bit part of the reference.
And in any case it is cleaner to have the data types matching here.
If device_register() returns error in siox_device_add(),
the name allocated by dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path. So fix this
by calling put_device(), then the name can be freed in
kobject_cleanup(), and sdevice is freed in siox_device_release(),
set it to null in error path.
Fixes: 97987337042b ("siox: new driver framework for eckelmann SIOX") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20221104021334.618189-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In accordance with [1] the DMA-able memory buffers must be
cacheline-aligned otherwise the cache writing-back and invalidation
performed during the mapping may cause the adjacent data being lost. It's
specifically required for the DMA-noncoherent platforms [2]. Seeing the
opal_dev.{cmd,resp} buffers are implicitly used for DMAs in the NVME and
SCSI/SD drivers in framework of the nvme_sec_submit() and sd_sec_submit()
methods respectively they must be cacheline-aligned to prevent the denoted
problem. One of the option to guarantee that is to kmalloc the buffers
[2]. Let's explicitly allocate them then instead of embedding into the
opal_dev structure instance.
Note this fix was inspired by the commit 30b8bd365b4a ("nvme-hwmon:
kmalloc the NVME SMART log buffer").
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit afc5aa7b6470 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: afc5aa7b6470 ("serial: 8250_omap: Fix probe and remove for PM runtime") Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: c4a28fe77ffc ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
BUG: KASAN: use-after-free in device_del+0xb5b/0xc60
Read of size 8 at addr ffff888008655050 by task rmmod/387
CPU: 2 PID: 387 Comm: rmmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x79/0x9a
print_report+0x17f/0x47b
kasan_report+0xbb/0xf0
device_del+0xb5b/0xc60
platform_device_del.part.0+0x24/0x200
platform_device_unregister+0x2e/0x40
snd_soc_exit+0xa/0x22 [snd_soc_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
It's bacause in snd_soc_init(), snd_soc_util_init() is possble to fail,
but its ret is ignored, which makes soc_dummy_dev unregistered twice.
snd_soc_init()
snd_soc_util_init()
platform_device_register_simple(soc_dummy_dev)
platform_driver_register() # fail
platform_device_unregister(soc_dummy_dev)
platform_driver_register() # success
...
snd_soc_exit()
snd_soc_util_exit()
# soc_dummy_dev will be unregistered for second time
To fix it, handle error and stop snd_soc_init() when util_init() fail.
Also clean debugfs when util_init() or driver_register() fail.
Fixes: e2e49ab152be ("ASoC: Work around allmodconfig failure") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221028031603.59416-1-chenzhongjin@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: 5e75d576a13b6 ("spi: stm32: Rate-limit the 'Communication suspended' message") Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Acked-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
l2cap_global_chan_by_psm shall not return fixed channels as they are not
meant to be connected by (S)PSM.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several places in the qgroup self tests follow the pattern of freeing the
ulist pointer they passed to btrfs_find_all_roots() if the call to that
function returned an error. That is pointless because that function always
frees the ulist in case it returns an error.
Also In some places like at test_multiple_refs(), after a call to
btrfs_qgroup_account_extent() we also leave "old_roots" and "new_roots"
pointing to ulists that were freed, because btrfs_qgroup_account_extent()
has freed those ulists, and if after that the next call to
btrfs_find_all_roots() fails, we call ulist_free() on the "old_roots"
ulist again, resulting in a double free.
So remove those calls to reduce the code size and avoid double ulist
free in case of an error.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mode_valid field in drm_connector_helper_funcs is expected to be of
type:
enum drm_mode_status (* mode_valid) (struct drm_connector *connector,
struct drm_display_mode *mode);
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of imx_tve_connector_mode_valid should be changed from
int to enum drm_mode_status.
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's a small window where a LOCK sent during a delegation return can
race with another OPEN on client, but the open stateid has not yet been
updated. In this case, the client doesn't handle the OLD_STATEID error
from the server and will lose this lock, emitting:
"NFS: nfs4_handle_delegation_recall_error: unhandled error -10024".
Fix this by sending the task through the nfs4 error handling in
nfs4_lock_done() when we may have to reconcile our stateid with what the
server believes it to be. For this case, the result is a retry of the
LOCK operation with the updated stateid.
Reported-by: Gonzalo Siero Humet <gsierohu@redhat.com> Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't use the test-specific header files as source files to force a
target dependency, as clang will complain if more than one source file
is used for a compile command with a single '-o' flag.
Use the proper Makefile variables instead as defined in
tools/testing/selftests/lib.mk.
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Tested-by: Adam Ford <aford173@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The iterator can not be greater than ATC_MAX_DSCR_TRIALS, as the for loop
will stop when i == ATC_MAX_DSCR_TRIALS. While here, use the common "i"
name for the iterator.
at_hdmac uses __raw_writel for register writes. In the absence of a
barrier, the CPU may reorder the register operations.
Introduce a write memory barrier so that the CPU does not reorder the
channel enable, thus the start of the transfer, without making sure that
all the pre-required register fields are already written.
In case the controller detected an error, the code took the chance to move
all the queued (submitted) descriptors to the active (issued) list. This
was wrong as if there were any descriptors in the submitted list they were
moved to the issued list without actually issuing them to the controller,
thus a completion could be raised without even fireing the descriptor.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove atc_dostart() from
atc_tx_submit(). Clients of at_xdmac that assume that tx_submit() starts
the transfer must be updated and call dma_async_issue_pending() if they
miss to call it.
The vdbg print was moved to after the lock is released. It is desirable to
do the prints without the lock held if possible, and because the if
statement disappears there's no reason why to do the print while holding
the lock.
Those hardware registers are all of 32 bits, while dma_addr_t ca be of
type u64 or u32 depending on CONFIG_ARCH_DMA_ADDR_T_64BIT. Force u32 to
comply with what the hardware expects.
OpenSSL 3.0 deprecated the OpenSSL's ENGINE API. That is as may be, but
the kernel build host tools still use it. Disable the warning about
deprecated declarations until somebody who cares fixes it.
The read access to struct canxl_frame::len inside of a j1939 created
skbuff revealed a missing initialization of reserved and later filled
elements in struct can_frame.
This patch initializes the 8 byte CAN header with zero.
loop0: detected capacity change from 0 to 2048
==================================================================
BUG: KASAN: slab-out-of-bounds in udf_find_entry+0x8a5/0x14f0
fs/udf/namei.c:253
Write of size 105 at addr ffff8880123ff896 by task syz-executor323/3610
The buggy address belongs to the object at ffff8880123ff800
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 150 bytes inside of
256-byte region [ffff8880123ff800, ffff8880123ff900)
The buggy address belongs to the physical page:
page:ffffea000048ff80 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0 pfn:0x123fe
head:ffffea000048ff80 order:1 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200ffffea00004b8500dead000000000003ffff888012041b40
raw: 0000000000000000000000008010001000000001ffffffff0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x0(),
pid 1, tgid 1 (swapper/0), ts 1841222404, free_ts 0
create_dummy_stack mm/page_owner.c:67 [inline]
register_early_stack+0x77/0xd0 mm/page_owner.c:83
init_page_owner+0x3a/0x731 mm/page_owner.c:93
kernel_init_freeable+0x41c/0x5d5 init/main.c:1629
kernel_init+0x19/0x2b0 init/main.c:1519
page_owner free stack trace missing
Memory state around the buggy address: ffff8880123ff780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8880123ff800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880123ff880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06
^ ffff8880123ff900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8880123ff980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fix this by changing the memory size allocated for copy_name from
UDF_NAME_LEN(254) to UDF_NAME_LEN_CS0(255), because the total length
(lfi) of subsequent memcpy can be up to 255.
CC: stable@vger.kernel.org Reported-by: syzbot+69c9fdccc6dd08961d34@syzkaller.appspotmail.com Fixes: ebe42040dd4f ("udf: Use separate buffer for copying split names") Signed-off-by: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20221109013542.442790-1-zhangpeng362@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After upgrading BIOS to U82 01.02.01 Rev.A, the console is flooded
strange char "^@" which printed out every second and makes login
nearly impossible. Also the below messages were shown both in console
and journal/dmesg every second:
usb 1-3: Device not responding to setup address.
usb 1-3: device not accepting address 4, error -71
usb 1-3: device descriptor read/all, error -71
usb usb1-port3: unable to enumerate USB device
Wifi is soft blocked by checking rfkill. When unblocked manually,
after few seconds it would be soft blocked again. So I was suspecting
something triggered rfkill to soft block wifi. At the end it was
fixed by removing hp_wmi module.
The root cause is the way hp-wmi driver handles command 1B on
post-2009 BIOS. In pre-2009 BIOS, command 1Bh return 0x4 to indicate
that BIOS no longer controls the power for the wireless devices.
We need to iterate over the original entries here for the sg_table,
pulling out the struct page for each one, to be remapped. However
currently this incorrectly iterates over the final dma mapped entries,
which is likely just one gigantic sg entry if the iommu is enabled,
leading to us only mapping the first struct page (and any physically
contiguous pages following it), even if there is potentially lots more
data to follow.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7306 Fixes: 3e85784a44c2 ("i915: add dmabuf/prime buffer sharing support.") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Michael J. Ruhl <michael.j.ruhl@intel.com> Cc: <stable@vger.kernel.org> # v3.5+ Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221028155029.494736-1-matthew.auld@intel.com
(cherry picked from commit 28d52f99bbca7227008cf580c9194c9b3516968e) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a nilfs2 filesystem is downgraded to read-only due to metadata
corruption on disk and is remounted read/write, or if emergency read-only
remount is performed, detaching a log writer and synchronizing the
filesystem can be done at the same time.
In these cases, use-after-free of the log writer (hereinafter
nilfs->ns_writer) can happen as shown in the scenario below:
While Task1 is sleeping, nilfs->ns_writer is freed by Task2. After Task1
waked up, Task1 accesses nilfs->ns_writer which is already freed. This
scenario diagram is based on the Shigeru Yoshida's post [1].
This patch fixes the issue by not detaching nilfs->ns_writer on remount so
that this UAF race doesn't happen. Along with this change, this patch
also inserts a few necessary read-only checks with superblock instance
where only the ns_writer pointer was used to check if the filesystem is
read-only.
A semaphore deadlock can occur if nilfs_get_block() detects metadata
corruption while locating data blocks and a superblock writeback occurs at
the same time:
task 1 task 2
------ ------
* A file operation *
nilfs_truncate()
nilfs_get_block()
down_read(rwsem A) <--
nilfs_bmap_lookup_contig()
... generic_shutdown_super()
nilfs_put_super()
* Prepare to write superblock *
down_write(rwsem B) <--
nilfs_cleanup_super()
* Detect b-tree corruption * nilfs_set_log_cursor()
nilfs_bmap_convert_error() nilfs_count_free_blocks()
__nilfs_error() down_read(rwsem A) <--
nilfs_set_error()
down_write(rwsem B) <--
*** DEADLOCK ***
Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem)
and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata
corruption, __nilfs_error() is called from nilfs_bmap_convert_error()
inside the lock section.
Since __nilfs_error() calls nilfs_set_error() unless the filesystem is
read-only and nilfs_set_error() attempts to writelock rwsem B (=
nilfs->ns_sem) to write back superblock exclusively, hierarchical lock
acquisition occurs in the order rwsem A -> rwsem B.
Now, if another task starts updating the superblock, it may writelock
rwsem B during the lock sequence above, and can deadlock trying to
readlock rwsem A in nilfs_count_free_blocks().
However, there is actually no need to take rwsem A in
nilfs_count_free_blocks() because it, within the lock section, only reads
a single integer data on a shared struct with
nilfs_sufile_get_ncleansegs(). This has been the case after commit 287570da6f5c ("nilfs2: add local variable to cache the number of clean
segments"), that is, even before this bug was introduced.
So, this resolves the deadlock problem by just not taking the semaphore in
nilfs_count_free_blocks().
Commit f42029f86457 ("vmlinux.lds.h: Avoid orphan section with !SMP")
fixed an orphan section warning by adding the '.data..decrypted' section
to the linker script under the PERCPU_DECRYPTED_SECTION define but that
placement introduced a panic with !SMP, as the percpu sections are not
instantiated with that configuration so attempting to access variables
defined with DEFINE_PER_CPU_DECRYPTED() will result in a page fault.
Move the '.data..decrypted' section to the DATA_MAIN define so that the
variables in it are properly instantiated at boot time with
CONFIG_SMP=n.
Accuphase DAC-60 option card supports native DSD up to DSD256,
but doesn't have support for auto-detection. Explicitly enable
DSD support for the correct altsetting.
M-Audio Micro (0762:201a) defines the descriptor as vendor-specific,
while the content seems class-compliant. Just overriding the probe
makes the device working.
As 'kobject_add' may allocated memory for 'kobject->name' when return error.
And in this function, if call 'kobject_add' failed didn't free kobject.
So call 'kobject_put' to recycling resources.
The Z390 DARK mainboard uses a CA0132 audio controller. The quirk is
needed to enable surround sound and 3.5mm headphone jack handling in
the front audio connector as well as in the rear of the board when in
stereo mode.
Page 97 of the linked manual contains instructions to setup the
controller.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit fbe0a8dc7ce8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 665de7e90761 ("mmc: tegra: HW Command Queue Support for Tegra SDMMC") Signed-off-by: Brian Norris <briannorris@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221026124150.v4.5.I418c9eaaf754880fcd2698113e8c3ef821a944d7@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but one
particular case I hit commonly enough: mmc_suspend() -> mmc_power_off().
Typically we will eventually deactivate CQE (cqhci_suspend() ->
cqhci_deactivate()), but that's not guaranteed -- in particular, if
we perform a partial (e.g., interrupted) system suspend.
The same bug was already found and fixed for two other drivers, in v5.7
and v5.9:
710de671a6b8 ("mmc: sdhci-msm: Deactivate CQE during SDHC reset") fbe0a8dc7ce8 ("mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel
GLK-based controllers")
The latter is especially prescient, saying "other drivers using CQHCI
might benefit from a similar change, if they also have CQHCI reset by
SDHCI_RESET_ALL."
So like these other patches, deactivate CQHCI when resetting the
controller. Do this via the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 57e19c7e7281 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20221026124150.v4.2.I29f6a2189e84e35ad89c1833793dca9e36c64297@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several SDHCI drivers need to deactivate command queueing in their reset
hook (see sdhci_cqhci_reset() / sdhci-pci-core.c, for example), and
several more are coming.
Those reset implementations have some small subtleties (e.g., ordering
of initialization of SDHCI vs. CQHCI might leave us resetting with a
NULL ->cqe_private), and are often identical across different host
drivers.
We also don't want to force a dependency between SDHCI and CQHCI, or
vice versa; non-SDHCI drivers use CQHCI, and SDHCI drivers might support
command queueing through some other means.
So, implement a small helper, to avoid repeating the same mistakes in
different drivers. Simply stick it in a header, because it's so small it
doesn't deserve its own module right now, and inlining to each driver is
pretty reasonable.
This is marked for -stable, as it is an important prerequisite patch for
several SDHCI controller bugfixes that follow.
Currently, when mapping the EFI runtime regions in the EFI page tables,
we complain about misaligned regions in a rather noisy way, using
WARN().
Not only does this produce a lot of irrelevant clutter in the log, it is
factually incorrect, as misaligned runtime regions are actually allowed
by the EFI spec as long as they don't require conflicting memory types
within the same 64k page.
So let's drop the warning, and tweak the code so that we
- take both the start and end of the region into account when checking
for misalignment
- only revert to RWX mappings for non-code regions if misaligned code
regions are also known to exist.
thread_struct's s[12] may contain random kernel memory content, which
may be finally leaked to userspace. This is a security hole. Fix it
by clearing the s[12] array in thread_struct when fork.
As for kthread case, it's better to clear the s[12] array as well.
In the scenario where the macvlan mode is configured as 'source',
macvlan_changelink_sources() will be execured to reconfigure list of
remote source mac addresses, at the same time, if register_netdevice()
return an error, the resource generated by macvlan_changelink_sources()
is not cleaned up.
Using this patch, in the case of an error, it will execute
macvlan_flush_sources() to ensure that the resource is cleaned up.
Fixes: 1d2e9c1bcaa8 ("driver: macvlan: Destroy new macvlan port if macvlan_common_newlink failed.") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Link: https://lore.kernel.org/r/20221109090735.690500-1-nashuiliang@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to init rxq or txq in mv643xx_eth_open() for opening device,
napi isn't disabled. When open mv643xx_eth device next time, it will
trigger a BUG_ON() in napi_enable(). Compile tested only.
Fixes: 88afea138e93 ("mv643xx_eth: get rid of receive-side locking") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109025432.80900-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to start nic or add interrupt service routine in
s2io_card_up() for opening device, napi isn't disabled. When open
s2io device next time, it will trigger a BUG_ON()in napi_enable().
Compile tested only.
Fixes: e66a2ac4f99e ("S2io: Fixed synchronization between scheduling of napi with card reset and close") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109023741.131552-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When t4vf_update_port_info() failed in cxgb4vf_open(), resources applied
during adapter goes up are not cleared. Fix it. Only be compiled, not be
tested.
Fixes: d00e44244c07 ("cxgb4vf: Update port information in cxgb4vf_open()") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221109012100.99132-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to bind qsets in cxgb_up() for opening device, napi isn't
disabled. When open cxgb3 device next time, it will trigger a BUG_ON()
in napi_enable(). Compile tested only.
When failed to create xdp rxqs or fill rx channels in cpsw_ndo_open() for
opening device, napi isn't disabled. When open cpsw device next time, it
will report a invalid opcode issue. Compiled tested only.
For a single CPU system, the kernel thread executing mlx5_cmd_flush()
never releases the CPU but calls down_trylock(&cmd→sem) in a busy loop.
On a single processor system, this leads to a deadlock as the kernel
thread which executes mlx5_cmd_invoke() never gets scheduled. Fix this,
by adding the cond_resched() call to the loop, allow the command
completion kernel thread to execute.
Fixes: 1bea202da238 ("net/mlx5: Set command entry semaphore up once got index free") Signed-off-by: Alexander Schmidt <alexschm@de.ibm.com> Signed-off-by: Roy Novich <royno@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to enable interrupts in nixge_open() for opening device,
napi isn't disabled. When open nixge device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
Fixes: 2da75fbce8af ("net: ethernet: nixge: Add support for National Instruments XGE netdev") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20221107101443.120205-1-shaozhengchao@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
'perf stat' with CSV output option prints an extra empty string as first
field in metrics output line. Sample output below:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,1.78,msec,cpu-clock,1785146,100.00,0.973,CPUs utilized
S0,1,26,,context-switches,1781750,100.00,0.015,M/sec
S0,1,1,,cpu-migrations,1780526,100.00,0.561,K/sec
S0,1,1,,page-faults,1779060,100.00,0.561,K/sec
S0,1,875807,,cycles,1769826,100.00,0.491,GHz
S0,1,85281,,stalled-cycles-frontend,1767512,100.00,9.74,frontend cycles idle
S0,1,576839,,stalled-cycles-backend,1766260,100.00,65.86,backend cycles idle
S0,1,288430,,instructions,1762246,100.00,0.33,insn per cycle
====> ,S0,1,,,,,,,2.00,stalled cycles per insn
The above command line uses field separator as "," via "-x," option and
per-socket option displays socket value as first field. But here the
last line for "stalled cycles per insn" has "," in the beginning.
Sample output using interval mode:
# ./perf stat -I 1000 -x, --per-socket -a -C 1 ls
0.001813453,S0,1,1.87,msec,cpu-clock,1872052,100.00,0.002,CPUs utilized
0.001813453,S0,1,2,,context-switches,1868028,100.00,1.070,K/sec
------
0.001813453,S0,1,85379,,instructions,1856754,100.00,0.32,insn per cycle
====> 0.001813453,,S0,1,,,,,,,1.34,stalled cycles per insn
Above result also has an extra CSV separator after
the timestamp. Patch addresses extra field separator
in the beginning of the metric output line.
The counter stats are displayed by function
"perf_stat__print_shadow_stats" in code
"util/stat-shadow.c". While printing the stats info
for "stalled cycles per insn", function "new_line_csv"
is used as new_line callback.
The new_line_csv function has check for "os->prefix"
and if prefix is not null, it will be printed along
with cvs separator.
Snippet from "new_line_csv":
if (os->prefix)
fprintf(os->fh, "%s%s", os->prefix, config->csv_sep);
Here os->prefix gets printed followed by ","
which is the cvs separator. The os->prefix is
used in interval mode option ( -I ), to print
time stamp on every new line. But prefix is
already set to contain CSV separator when used
in interval mode for CSV option.
Also if prefix is not assigned (if not used with
-I option), it gets set to empty string.
Reference: function printout() in util/stat-display.c
Snippet:
.prefix = prefix ? prefix : "",
Since prefix already set to contain cvs_sep in interval
option, patch removes printing config->csv_sep in
new_line_csv function to avoid printing extra field.
After the patch:
# ./perf stat -x, --per-socket -a -C 1 ls
S0,1,2.04,msec,cpu-clock,2045202,100.00,1.013,CPUs utilized
S0,1,2,,context-switches,2041444,100.00,979.289,/sec
S0,1,0,,cpu-migrations,2040820,100.00,0.000,/sec
S0,1,2,,page-faults,2040288,100.00,979.289,/sec
S0,1,254589,,cycles,2036066,100.00,0.125,GHz
S0,1,82481,,stalled-cycles-frontend,2032420,100.00,32.40,frontend cycles idle
S0,1,113170,,stalled-cycles-backend,2031722,100.00,44.45,backend cycles idle
S0,1,88766,,instructions,2030942,100.00,0.35,insn per cycle
S0,1,,,,,,,1.27,stalled cycles per insn
Fixes: 914146c85d57ba20 ("perf stat: Implement CSV metrics output") Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com> Reviewed-By: Kajol Jain <kjain@linux.ibm.com> Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Tested-by: Disha Goel <disgoel@linux.vnet.ibm.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nageswara R Sastry <rnsastry@linux.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20221018085605.63834-1-atrajeev@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failed to register irq in xgene_enet_open() for opening device,
napi isn't disabled. When open xgene device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 067159824b49 ("driver core: platform: Add an error message to platform_get_irq*()") Signed-off-by: Doug Brown <doug@schmorgal.com> Link: https://lore.kernel.org/r/20220906000709.52705-1-doug@schmorgal.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a follow-up for commit d895b8d851c6 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
It causes NULL pointer dereference when testing as following:
(a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket.
(b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan
link device, and bind vxcan device to bond device (can also use
ifenslave command to bind vxcan device to bond device).
(c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket.
(d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket.
The bond device invokes the can-raw protocol registration interface to
receive CAN packets. However, ml_priv is not allocated to the dev,
dev_rcv_lists is assigned to NULL in can_rx_register(). In this case,
it will occur the NULL pointer dereference issue.
The following is the stack information:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:can_rx_register+0x12d/0x1e0
Call Trace:
<TASK>
raw_enable_filters+0x8d/0x120
raw_enable_allfilters+0x3b/0x130
raw_bind+0x118/0x4f0
__sys_bind+0x163/0x1a0
__x64_sys_bind+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 82817a015495 ("net: introduce CAN specific pointer in the struct net_device") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/all/20221028085650.170470-1-shaozhengchao@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch ensures that the reserved field is always initialized.
Reported-by: syzbot+3553517af6020c4f2813f1003fe76ef3cbffe98d@syzkaller.appspotmail.com Fixes: 50b1de658254 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Signed-off-by: Alexander Potapenko <glider@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A problem about modprobe vc4 failed is triggered with the following log
given:
[ 420.327987] Error: Driver 'vc4_hvs' is already registered, aborting...
[ 420.333904] failed to register platform driver vc4_hvs_driver [vc4]: -16
modprobe: ERROR: could not insert 'vc4': Device or resource busy
The reason is that vc4_drm_register() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
fails, it returns without unregistering all the vc4 drivers, resulting the
vc4 can never be installed later.
A simple call graph is shown as below:
vc4_drm_register()
platform_register_drivers() # all vc4 drivers are registered
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without unregister drivers
Fixing this problem by checking the return value of
platform_driver_register() and do platform_unregister_drivers() if
error happened.
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, bpq_device_event() receives the message
and creates a new bpq device. In this case, the reference count value of
dev is hold once. But after "ifenslave -f bond2 rose1" command is
executed, the type of the bond device is changed to rose. When the bond
device is unregistered, bpq_device_event() will not put the dev reference
count.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When following tests are performed, it will cause dev reference counting
leakage.
a)ip link add bond2 type bond mode balance-rr
b)ip link set bond2 up
c)ifenslave -f bond2 rose1
d)ip link del bond2
When new bond device is created, the default type of the bond device is
ether. And the bond device is up, lapbeth_device_event() receives the
message and creates a new lapbeth device. In this case, the reference
count value of dev is hold once. But after "ifenslave -f bond2 rose1"
command is executed, the type of the bond device is changed to rose. When
the bond device is unregistered, lapbeth_device_event() will not put the
dev reference count.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in security/commoncap.c:1252:2
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
cap_task_prctl+0x561/0x6f0
security_task_prctl+0x5a/0xb0
__x64_sys_prctl+0x61/0x8f0
do_syscall_64+0x58/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 59bf6ceeb8d1 ("Add 64-bit capability support to the kernel") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the mac device gets removed, it leaves behind the ethernet device.
This will result in a segfault next time the ethernet device accesses
mac_dev. Remove the ethernet device when we get removed to prevent
this. This is not completely reversible, since some resources aren't
cleaned up properly, but that can be addressed later.
In the bnxt_en driver ndo_rx_flow_steer returns '0' whenever an entry
that we are attempting to steer is already found. This is not the
correct behavior. The return code should be the value/index that
corresponds to the entry. Returning zero all the time causes the
RFS records to be incorrect unless entry '0' is the correct one. As
flows migrate to different cores this can create entries that are not
correct.
Fixes: 93658deae41f ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Akshay Navgire <anavgire@purestorage.com> Signed-off-by: Alex Barba <alex.barba@broadcom.com> Signed-off-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During the error recovery sequence, the rtnl_lock is not held for the
entire duration and some datastructures may be freed during the sequence.
Check for the BNXT_STATE_OPEN flag instead of netif_running() to ensure
that the device is fully operational before proceeding to reconfigure
the coalescing settings.
The issue occurs in the following scenarios:
tun_get_user()
napi_gro_frags()
napi_frags_finish()
case GRO_NORMAL:
gro_normal_one()
list_add_tail(&skb->list, &napi->rx_list);
<-- While napi->rx_count < READ_ONCE(gro_normal_batch),
<-- gro_normal_list() is not called, napi->rx_list is not empty
<-- not ask to complete the gro work, will cause memory leaks in
<-- following tun_napi_del()
...
tun_napi_del()
netif_napi_del()
__netif_napi_del()
<-- &napi->rx_list is not empty, which caused memory leaks
To fix, add napi_complete() after napi_gro_frags().
Fixes: dbb28a8499aa ("tun: enable napi_gro_frags() for TUN/TAP driver") Signed-off-by: Wang Yufen <wangyufen@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit dbb1dc6704ca ("net: gso: Fix skb_segment splat when
splitting gso_size mangled skb having linear-headed frag_list"), it is
allowed to change gso_size of a GRO packet. However, that commit assumes
that "checking the first list_skb member suffices; i.e if either of the
list_skb members have non head_frag head, then the first one has too".
It turns out this assumption does not hold. We've seen BUG_ON being hit
in skb_segment when skbs on the frag_list had differing head_frag with
the vmxnet3 driver. This happens because __netdev_alloc_skb and
__napi_alloc_skb can return a skb that is page backed or kmalloced
depending on the requested size. As the result, the last small skb in
the GRO packet can be kmalloced.
There are three different locations where this can be fixed:
(1) We could check head_frag in GRO and not allow GROing skbs with
different head_frag. However, that would lead to performance
regression on normal forward paths with unmodified gso_size, where
!head_frag in the last packet is not a problem.
(2) Set a flag in bpf_skb_net_grow and bpf_skb_net_shrink indicating
that NETIF_F_SG is undesirable. That would need to eat a bit in
sk_buff. Furthermore, that flag can be unset when all skbs on the
frag_list are page backed. To retain good performance,
bpf_skb_net_grow/shrink would have to walk the frag_list.
(3) Walk the frag_list in skb_segment when determining whether
NETIF_F_SG should be cleared. This of course slows things down.
This patch implements (3). To limit the performance impact in
skb_segment, the list is walked only for skbs with SKB_GSO_DODGY set
that have gso_size changed. Normal paths thus will not hit it.
We could check only the last skb but since we need to walk the whole
list anyway, let's stay on the safe side.
Fixes: dbb1dc6704ca ("net: gso: Fix skb_segment splat when splitting gso_size mangled skb having linear-headed frag_list") Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/e04426a6a91baf4d1081e1b478c82b5de25fdf21.1667407944.git.jbenc@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root case is in commit a7b24bfb6731 ("bpf, sockmap: Fix more uncharged
while msg has more_data"), where I used msg->sg.size to replace the tosend,
causing breakage:
if (msg->apply_bytes && msg->apply_bytes < tosend)
tosend = psock->apply_bytes;
Fixes: a7b24bfb6731 ("bpf, sockmap: Fix more uncharged while msg has more_data") Reported-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/1667266296-8794-1-git-send-email-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function query_regdb_file() the alpha2 parameter is duplicated
using kmemdup() and subsequently freed in regdb_fw_cb(). However,
request_firmware_nowait() can fail without calling regdb_fw_cb() and
thus leak memory.
Fixes: 2bb24f727ff9 ("cfg80211: support loading regulatory database as firmware file") Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All we're going to do with this pointer is assign it to
another __rcu pointer, but sparse can't see that, so
use rcu_access_pointer() to silence the warning here.
Fixes: f7cc18a1b705 ("wifi: cfg80211: update hidden BSSes to avoid WARN_ON") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xfsaild is racy with respect to transaction abort and shutdown in
that the task can idle or exit with an empty AIL but buffers still
on the delwri queue. This was partly addressed by cancelling the
delwri queue before the task exits to prevent memory leaks, but it's
also possible for xfsaild to empty and idle with buffers on the
delwri queue. For example, a transaction that pins a buffer that
also happens to sit on the AIL delwri queue will explicitly remove
the associated log item from the AIL if the transaction aborts. The
side effect of this is an unmount hang in xfs_wait_buftarg() as the
associated buffers remain held by the delwri queue indefinitely.
This is reproduced on repeated runs of generic/531 with an fs format
(-mrmapbt=1 -bsize=1k) that happens to also reproduce transaction
aborts.
Update xfsaild to not idle until both the AIL and associated delwri
queue are empty and update the push code to continue delwri queue
submission attempts even when the AIL is empty. This allows the AIL
to eventually release aborted buffers stranded on the delwri queue
when they are unlocked by the associated transaction. This should
have no significant effect on normal runtime behavior because the
xfsaild currently idles only when the AIL is empty and in practice
the AIL is rarely empty with a populated delwri queue. The items
must be AIL resident to land in the queue in the first place and
generally aren't removed until writeback completes.
Note that the pre-existing delwri queue cancel logic in the exit
path is retained because task stop is external, could technically
come at any point, and xfsaild is still responsible to release its
buffer references before it exits.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ For 5.4.y, SB_I_VERSION should be set in xfs_fs_remount() ]
The MS_I_VERSION mount flag is exposed via the VFS, as documented
in the mount manpages etc; see the iversion and noiversion mount
options in mount(8).
As a result, mount -o remount looks for this option in /proc/mounts
and will only send the I_VERSION flag back in during remount it it
is present. Since it's not there, a remount will /remove/ the
I_VERSION flag at the vfs level, and iversion functionality is lost.
xfs v5 superblocks intend to always have i_version enabled; it is
set as a default at mount time, but is lost during remount for the
reasons above.
The generic fix would be to expose this documented option in
/proc/mounts, but since that was rejected, fix it up again in the
xfs remount path instead, so that at least xfs won't suffer from
this misbehavior.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page faultround path ->map_pages is implemented in XFS via
filemap_map_pages(). This function checks that pages found in page
cache lookups have not raced with truncate based invalidation by
checking page->mapping is correct and page->index is within EOF.
However, we've known for a long time that this is not sufficient to
protect against races with invalidations done by operations that do
not change EOF. e.g. hole punching and other fallocate() based
direct extent manipulations. The way we protect against these
races is we wrap the page fault operations in a XFS_MMAPLOCK_SHARED
lock so they serialise against fallocate and truncate before calling
into the filemap function that processes the fault.
Do the same for XFS's ->map_pages implementation to close this
potential data corruption issue.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing reflink remapping loop has some structural problems that
need addressing:
The biggest problem is that we create one transaction for each extent in
the source file without accounting for the number of mappings there are
for the same range in the destination file. In other words, we don't
know the number of remap operations that will be necessary and we
therefore cannot guess the block reservation required. On highly
fragmented filesystems (e.g. ones with active dedupe) we guess wrong,
run out of block reservation, and fail.
The second problem is that we don't actually use the bmap intents to
their full potential -- instead of calling bunmapi directly and having
to deal with its backwards operation, we could call the deferred ops
xfs_bmap_unmap_extent and xfs_refcount_decrease_extent instead. This
makes the frontend loop much simpler.
Solve all of these problems by refactoring the remapping loops so that
we only perform one remapping operation per transaction, and each
operation only tries to remap a single extent from source to dest.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reported-by: Edwin Török <edwin@etorok.net> Tested-by: Edwin Török <edwin@etorok.net> Acked-by: Darrick J. Wong <djwong@kernel.org>
[backported to 5.4.y - Tested-by above does not refer to the backport] Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of this predicate is a little misleading -- it decides if the
extent mapping is allocated and written. Change the name to be more
direct, as we're going to add a new predicate in the next patch.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Slightly modify xfs_trans_alloc() to fix a merge conflict due to missing
"atomic_inc(&mp->m_active_trans)" statement in v5.9 kernel]
The rmapbt extent swap algorithm remaps individual extents between
the source inode and the target to trigger reverse mapping metadata
updates. If either inode straddles a format or other bmap allocation
boundary, the individual unmap and map cycles can trigger repeated
bmap block allocations and frees as the extent count bounces back
and forth across the boundary. While net block usage is bound across
the swap operation, this behavior can prematurely exhaust the
transaction block reservation because it continuously drains as the
transaction rolls. Each allocation accounts against the reservation
and each free returns to global free space on transaction roll.
The previous workaround to this problem attempted to detect this
boundary condition and provide surplus block reservation to
acommodate it. This is insufficient because more remaps can occur
than implied by the extent counts; if start offset boundaries are
not aligned between the two inodes, for example.
To address this problem more generically and dynamically, add a
transaction accounting mode that returns freed blocks to the
transaction reservation instead of the superblock counters on
transaction roll and use it when the rmapbt based algorithm is
active. This allows the chain of remap transactions to preserve the
block reservation based own its own frees and prevent premature
exhaustion regardless of the remap pattern. Note that this is only
safe for superblocks with lazy sb accounting, but the latter is
required for v5 supers and the rmap feature depends on v5.
Fixes: b85c50c931b80 ("xfs: account format bouncing into rmapbt swapext tx reservation") Root-caused-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus proposes to revert an accounting for sops objects in
do_semtimedop() because it's really just a temporary buffer
for a single semtimedop() system call.
This object can consume up to 2 pages, syscall is sleeping
one, size and duration can be controlled by user, and this
allocation can be repeated by many thread at the same time.
However Shakeel Butt pointed that there are much more popular
objects with the same life time and similar memory
consumption, the accounting of which was decided to be
rejected for performance reasons.
Considering at least 2 pages for task_struct and 2 pages for
the kernel stack, a back of the envelope calculation gives a
footprint amplification of <1.5 so this temporal buffer can be
safely ignored.
The factor would IMO be interesting if it was >> 2 (from the
PoV of excessive (ab)use, fine-grained accounting seems to be
currently unfeasible due to performance impact).
This patch fixes an intra-object buffer overflow in brcmfmac that occurs
when the device provides a 'bsscfgidx' equal to or greater than the
buffer size. The patch adds a check that leads to a safe failure if that
is the case.
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Reviewed-by: Arend van Spriel <aspriel@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Dokyung Song <dokyung.song@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221021061359.GA550858@laguna Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call intel_sdvo_select_ddc_bus() before initializing any
of the outputs. And before that is functional (assuming no VBT)
we have to set up the controlled_outputs thing. Otherwise DDC
won't be functional during the output init but LVDS really
needs it for the fixed mode setup.
Note that the whole multi output support still looks very
bogus, and more work will be needed to make it correct.
But for now this should at least fix the LVDS EDID fixed mode
setup.
Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7301 Fixes: 71f8b64f86bf ("drm/i915/sdvo: Fix multi function encoder stuff") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-3-ville.syrjala@linux.intel.com Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 64b7b557dc8a96d9cfed6aedbf81de2df80c025d) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We try to filter out the corresponding xxx1 output
if the xxx0 output is not present. But the way that is
being done is pretty awkward. Make it less so.
We can't safely probe a dual-DSI display asynchronously
(driver_async_probe='*' or driver_async_probe='dw-mipi-dsi-rockchip'
cmdline), because dw_mipi_dsi_rockchip_find_second() pokes one DSI
device's drvdata from the other device without any locking.
Request synchronous probe, at least until this driver learns some
appropriate locking for dual-DSI initialization.
48e40aeea1f92 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 48e40aeea1f92 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 48e40aeea1f92 ("mtd: rawnand: gpmi: Fix setting busy timeout setting") Fixes: 4941537c16932 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Han Xu <han.xu@nxp.com> Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log