Stefan Wahren [Sat, 9 May 2015 07:58:09 +0000 (07:58 +0000)]
net: qca_spi: Fix possible race during probe
Registering the netdev before setting the priv data is unsafe.
So fix this possible race by setting the priv data first.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Cc: <stable@vger.kernel.org> # v3.18+ Fixes: a93f2da6 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Vermeulen [Fri, 8 May 2015 14:18:49 +0000 (16:18 +0200)]
net: mdio-gpio: Allow for unspecified bus id
When the bus id was supplied via a struct platform_device, the driver wasn't
handling -1 to mean an unspecified id of the only instance of this driver,
as the platform spec requires.
Signed-off-by: Bert Vermeulen <bert@biot.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet / TX_RING not fully non-blocking (w/ MSG_DONTWAIT).
This patch fixes an issue where the send(MSG_DONTWAIT) call
on a TX_RING is not fully non-blocking in cases where the device's sndBuf is
full. We pass nonblock=true to sock_alloc_send_skb() and return any possibly
occuring error code (most likely EGAIN) to the caller. As the fast-path stays
as it is, we keep the unlikely() around skb == NULL.
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Thu, 7 May 2015 18:37:10 +0000 (20:37 +0200)]
bnx2x: limit fw delay in kdump to 5s after boot
Commit 90d992913c2a "bnx2x: Delay during kdump load" added a 5 seconds
delay to bnx2x's probe function in the kdump case to let the firmware
realize the old driver is gone.
The problem with the delay is that it is per-device, so if you have
several bnx2x NICs in NPAR mode, the delays can accumulate to minutes.
Fix it by adjusting the delay so that we do not wait more than
necessary, i.e. no more delaying after 5 seconds of kernel boot time.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ARM: net: delegate filter to kernel interpreter when imm_offset() return value can't fit into 12bits.
The ARM JIT code emits "ldr rX, [pc, #offset]" to access the literal
pool. #offset maximum value is 4095 and if the generated code is too
large, the #offset value can overflow and not point to the expected
slot in the literal pool. Additionally, when overflow occurs, bits of
the overflow can end up changing the destination register of the ldr
instruction.
Fix that by detecting the overflow in imm_offset() and setting a flag
that is checked for each BPF instructions converted in
build_body(). As of now it can only be detected in the second pass. As
a result the second build_body() call can now fail, so add the
corresponding cleanup code in that case.
Using multiple literal pools in the JITed code is going to require
lots of intrusive changes to the JIT code (which would better be done
as a feature instead of fix), just delegating to the kernel BPF
interpreter in that case is a more straight forward, minimal fix and
easy to backport.
Fixes: c20727afedd8 ("ARM: 7259/3: net: JIT compiler for packet filters") Signed-off-by: Nicolas Schichan <nschichan@freebox.fr> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
ARM: net fix emit_udiv() for BPF_ALU | BPF_DIV | BPF_K intruction.
In that case, emit_udiv() will be called with rn == ARM_R0 (r_scratch)
and loading rm first into ARM_R0 will result in jit_udiv() function
being called the same dividend and divisor. Fix that by loading rn
first into ARM_R1 and then rm into ARM_R0.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr> Cc: <stable@vger.kernel.org> # v3.13+ Fixes: 200285d3b790 (bpf: do not use reciprocal divide) Acked-by: Mircea Gherzan <mgherzan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 10 May 2015 02:23:59 +0000 (22:23 -0400)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-05-07
This series contains updates to igb only.
Toshiaki provides two fixes for igb, first fixes an issue when changing
the number of rings by ethtool which causes oops because of uninitialized
pointers. The second fix resolves a typo where tx_ring was used instead
of the desired rx_ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
transfer_buffer_length is of type u32. It's therefore wrong to assign it
to a signed integer. This patch avoids the overflow.
It's worth noting that entry->length here is a long; perhaps it would be
beneficial at somepoint to change this to be unsigned as well, if
nothing else relies on its signedness for error conditions or the like.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Wed, 6 May 2015 13:09:18 +0000 (09:09 -0400)]
netxen_nic: use spin_[un]lock_bh around tx_clean_lock (2)
This patch should have been part of the previous patch having the
same summary. See http://marc.info/?l=linux-kernel&m=143039470103795&w=2
Unfortunately, I didn't check to see where else this lock was used before
submitting that patch. This should take care of it for netxen_nic, as I
did a thorough search this time.
To recap from the original patch; although testing this driver with
DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled did not produce any traces,
it would be more prudent in the case of tx_clean_lock to use _bh
versions of spin_[un]lock, since this lock is manipulated in both
the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com> Acked-By: Neil Horman <nhorman@tuxdriver.com> Acked-By: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Wed, 6 May 2015 07:14:34 +0000 (09:14 +0200)]
net: xgene_enet: Set hardware dependency
The xgene_enet driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Iyappan Subramanian <isubramanian@apm.com> Cc: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Wed, 6 May 2015 07:04:40 +0000 (09:04 +0200)]
net: amd-xgbe: Add hardware dependency
The amd-xgbe driver currently only works with the Seattle SoC, which
is ARM64 architecture, so there is no point in building this driver on
other architectures except for build testing purpose. The dependency
list can be updated later if the driver ever supports other
architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Tue, 5 May 2015 22:22:02 +0000 (15:22 -0700)]
net_sched: fix a use-after-free in tc_ctl_tfilter()
When tcf_destroy() returns true, tp could be already destroyed,
we should not use tp->next after that.
For long term, we probably should move tp list to list_head.
Fixes: f3614e19fdae ("net_sched: destroy proto tp when all filters are gone") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Sullivan [Tue, 5 May 2015 20:00:25 +0000 (15:00 -0500)]
net: macb: Handle the RXUBR interrupt on all devices
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset
V2 changes: DaveM comments to reduce memory footprint, follow
NFS/RPC model where possible. Added test-case #3
Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.
Test cases used to verify the changes in this set are:
1. Start rds client/server applications on two participating nodes,
node1 and node2. After at least one packet has been sent (to establish
the TCP connection), restart the rds_tcp module on the client, and
now resend packets. Tcpdump should show server sending a FIN for the
"old" client port, and clean connection establishment/exchange for
the new client port.
2. At the end of step 1, restart rds srever on node2, and start client on
node1, make sure using tcpdump, 'netstat -an|grep 16385' that
packets flow correctly.
3. start RDS client/server application on two participating nodes, and
repeat steps 1 and 2, but this time, simulate node failure by doing
"ifconfig <intf> down", so no FIN is sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/rds: RDS-TCP: only initiate reconnect attempt on outgoing TCP socket.
When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/rds: RDS-TCP: Always create a new rds_sock for an incoming connection.
When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT. After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state. If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).
This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Stenberg [Tue, 5 May 2015 10:36:59 +0000 (13:36 +0300)]
ipv6: Fixed source specific default route handling.
If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.
The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.
Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
Signed-off-by: Markus Stenberg <markus.stenberg@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 9 May 2015 19:51:00 +0000 (15:51 -0400)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:
- mac802154 fix for crypto algorithm allocation failure checking
- mac802154 wpan phy leak fix for error code path
- Fix for not calling Bluetooth shutdown() if interface is not up
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
igb: Fix NULL assignment to incorrect variable in igb_reset_q_vector
adapter->tx_ring is set to NULL where rx_ring should be.
Fixes: dc38615eac1d ("igb: Combine q_vector and ring allocation into a single function") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.
- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
misleads igb_poll() to determine that it has an rx ring although it
actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
(q_vector->ring[0].skb) has a value that was used as tx_stats before.
Fix these problems by zeroing it out on reuseing it.
Fixes: 18bbb5326195 ("igb: Fix queue allocation method to accommodate changing during runtime") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Wed, 29 Apr 2015 23:20:58 +0000 (16:20 -0700)]
tcp_westwood: fix tcp_westwood_info()
I forgot to update tcp_westwood when changing get_info() behavior,
this patch should fix this.
Fixes: 9fa1aed4ef44 ("tcp: prepare CC get_info() access from getsockopt()") Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 May 2015 23:41:33 +0000 (19:41 -0400)]
Merge tag 'wireless-drivers-for-davem-2015-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)
Yishai Hadas [Tue, 5 May 2015 14:07:12 +0000 (17:07 +0300)]
net/mlx4_core: Work properly with EQ numbers > 256 in SRIOV
The Firmware uses dynamic EQs allocation based on number of VFs and
max EQs that can be allocated. As a result, VF can have EQ numbers
that are larger than 256.
According to the firmware spec, the max value is limited to be 1024
(10 bits), adapt the relevant code accordingly. This bug was impossible
to hit prior to commit 2c2c54eda995 ("net/mlx4_core: Flexible (asymmetric)
allocation of EQs and MSI-X vectors for PF/VFs") which actually enables
large number of EQs for VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Tue, 5 May 2015 14:07:11 +0000 (17:07 +0300)]
net/mlx4_en: Fix off-by-one in counters manipulation
This caused the en_stats_adder helper to accumulate a field which is
not related to the counter, fix that.
Fixes: 6739729f74de ('net/mlx4_en: Moderate ethtool callback to show [..]') Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
hv_netvsc: remove unused variable in netvsc_send()
With commit 2f03d7124b69 ("hv_netvsc: Fix a bug in netvsc_start_xmit()"),
skb variable is no longer used in netvsc_send. Remove variable and dead
code that depended on it.
Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2015 20:00:55 +0000 (16:00 -0400)]
Merge tag 'mac80211-for-davem-2015-05-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have only a few fixes right now:
* a fix for an issue with hash collision handling in the
rhashtable conversion
* a merge issue - rhashtable removed default shrinking
just before mac80211 was converted, so enable it now
* remove an invalid WARN that can trigger with legitimate
userspace behaviour
* add a struct member missing from kernel-doc that caused
a lot of warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 4 May 2015 09:34:12 +0000 (12:34 +0300)]
bnx2x: Fix to prevent inner-reload
Submit 28ea9719dd25c ("bnx2x: Prevent inner-reload while VFs exist")
contained a bug - MTU change was not prevented by it; Instead, it
`randomally' prevented bnx2x_resume() from running [harmless yet wrong].
This moves the check to its correct spot.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the first bluetooth-next pull request for 4.2:
- Various fixes for at86rf230 driver
- ieee802154: trace events support for rdev->ops
- HCI UART driver refactoring
- New Realtek IDs added to btusb driver
- Off-by-one fix for rtl8723b in btusb driver
- Refactoring of btbcm driver for both UART & USB use
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 4 May 2015 15:51:38 +0000 (11:51 -0400)]
net/rds: Fix new sparse warning
34eea6d2f15 introduced new sparse warnings:
CHECK /home/dahern/kernels/linux.git/net/rds/ib_cm.c
net/rds/ib_cm.c:191:34: warning: incorrect type in initializer (different base types)
net/rds/ib_cm.c:191:34: expected unsigned long long [unsigned] [usertype] dp_ack_seq
net/rds/ib_cm.c:191:34: got restricted __be64 <noident>
net/rds/ib_cm.c:194:51: warning: cast to restricted __be64
The temporary variable for sequence number should have been declared as __be64
rather than u64. Make it so.
Signed-off-by: David Ahern <david.ahern@oracle.com> Cc: shamir rabinovitch <shamir.rabinovitch@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kamlakant Patel [Mon, 4 May 2015 09:09:49 +0000 (14:39 +0530)]
net/smsc911x: fix irq resource allocation failure
When smsc911x uses GPIO as the interrupt controller, and if both are
loaded as modules, we get following error:
"smsc911x: Could not allocate irq resource"
This issue is because of smsc911x using platform_get_resource to get
device tree based irq resource.
commit "5f6ea80 (of/irq: do irq resolution in platform_get_irq)" and
commit "7085a7 (drivers: platform: parse IRQ flags from resources)" add
support in platform_get_irq to resolve irq and irq_flags respectively
for both modern device tree and legacy static platform data platforms.
Modify smsc911x driver to use platform_get_irq to pick up irq resource
correctly and use irq_get_trigger_type to get the IRQ trigger flags.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Sun, 3 May 2015 01:33:44 +0000 (21:33 -0400)]
net: core: Correct an over-stringent device loop detection.
The code in __netdev_upper_dev_link() has an over-stringent
loop detection logic that actually prevents valid configurations
from working correctly.
In particular, the logic returns an error if an upper device
is already in the list of all upper devices for a given dev.
This particular check seems to be a overzealous as it disallows
perfectly valid configurations. For example:
# ip l a link eth0 name eth0.10 type vlan id 10
# ip l a dev br0 typ bridge
# ip l s eth0.10 master br0
# ip l s eth0 master br0 <--- Will fail
If you switch the last two commands (add eth0 first), then both
will succeed. If after that, you remove eth0 and try to re-add
it, it will fail!
It appears to be enough to simply check adj_list to keeps things
safe.
I've tried stacking multiple devices multiple times in all different
combinations, and either rx_handler registration prevented the stacking
of the device linking cought the error.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Sat, 2 May 2015 17:23:22 +0000 (19:23 +0200)]
isdn/gigaset: cede maintainership
As German phone operators are discontinuing ISDN service, neither
Hansjörg nor I will be able to maintain the Gigaset ISDN drivers
any longer. Paul Bolle offered to step into the breach for odd
fixes.
Signed-off-by: Tilman Schmidt <tilman@imap.cc> Acked-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Fri, 1 May 2015 21:36:37 +0000 (17:36 -0400)]
macvlan: Propagate promiscuity setting to lower devices.
When a macvlan device is placed in promiscuous mode, it currently
just sets it's multicast mask to permissive, but doesn't change
the state of the lower device. As a result, not all multicast
traffic can be received on such device. Additionally, none of
a vlan traffic can be received on such device as well.
This patch propagates the promiscuous mode setting to lower device
so that lower device may receive all packets that macvlan may
be interested in.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
That patch is solving a non-existant problem while creating a
real problem. Just because a socket is allocated in the init
name space doesn't mean that it gets hashed in the init name space.
When we unhash it the name space must be the same as the one
we had when we hashed it. So this patch is completely bogus
and causes socket leaks.
Reported-by: Andrey Wagin <avagin@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 May 2015 04:06:56 +0000 (00:06 -0400)]
Merge branch 'dev_kfree_skb'
Alexander Duyck says:
====================
Clean-up some bits related to netpoll
This patch set cleans up some minor items related to netpoll. The first
patch addresses an Rx clean-up bug that is triggered due to an assumption
that napi->poll wouldn't be called with a budget of 0. The other two
patches address dev_kfree_skb being called in the xmit path which isn't
valid since netpoll will call ndo_start_xmit with IRQs disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 1 May 2015 17:34:50 +0000 (10:34 -0700)]
ixgbevf: Use dev_kfree_skb_any in xmit path, not dev_kfree_skb
With netpoll making use of the transmit function it is possible for the
ndo_start_xmit function to be called with irqs disabled. As such we need
to use dev_kfree_skb_any in the Tx cleanup path for frames that are
dropped.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 1 May 2015 17:34:44 +0000 (10:34 -0700)]
r8169: Do not use dev_kfree_skb in xmit path
The function r8169_csum_workaround is called in the ndo_start_xmit path of
the r8169 driver. As such it should not be using dev_kfree_skb as it is
not irq safe, so instead we should be using dev_kfree_skb_any for freeing
in the dropped path, and dev_consume_skb_any for any frames that were
transmitted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Fri, 1 May 2015 17:34:38 +0000 (10:34 -0700)]
fm10k: Do not assume budget will never be 0 for NAPI
The netpoll path will call napi->poll with a budget of 0 in order to clean
the Tx rings only. This change updates the fm10k driver so that it will
correctly support that instead of cleaning 1 Rx frame if a budget of 0 is
received.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 1 May 2015 14:43:52 +0000 (10:43 -0400)]
net: dsa: mv88e6xxx: unregister mv88e6352 driver
Add the missing unregister for the mv88e6352_switch_driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Fri, 1 May 2015 01:47:42 +0000 (21:47 -0400)]
drivers/net: include <module.h> for modular stmmac_platform code
This file is built off of a tristate Kconfig option and also contains
modular function calls so it should explicitly include module.h to
avoid compile breakage during header shuffles done in the future.
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: netdev@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rdma_conn_param private data is copied using memcpy after headers such
as cma_hdr (see cma_resolve_ib_udp as example). so the start of the
private data is aligned to the end of the structure that come before. if
this structure end with u32 the meaning is that the start of the private
data will be 4 bytes aligned. structures that use u8/u16/u32/u64 are
naturally aligned but in case the structure start is not 8 bytes aligned,
all u64 members of this structure will not be aligned. to solve this issue
we must use special macros that allow unaligned access to those
unaligned members.
Addresses the following kernel log seen when attempting to use RDMA:
Kernel unaligned access at TPC[10507a88] rds_ib_cm_connect_complete+0x1bc/0x1e0 [rds_rdma]
Acked-by: Chien Yen <chien.yen@oracle.com> Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
[Minor tweaks for top of tree by:] Signed-off-by: David Ahern <david.ahern@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Fri, 1 May 2015 00:27:59 +0000 (08:27 +0800)]
netlink: Remove max_size setting
We currently limit the hash table size to 64K which is very bad
as even 10 years ago it was relatively easy to generate millions
of sockets.
Since the hash table is naturally limited by memory allocation
failure, we don't really need an explicit limit so this patch
removes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Thomas Graf <tgraf@noironetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 30 Apr 2015 16:40:40 +0000 (09:40 -0700)]
codel: fix maxpacket/mtu confusion
Under presence of TSO/GSO/GRO packets, codel at low rates can be quite
useless. In following example, not a single packet was ever dropped,
while average delay in codel queue is ~100 ms !
This comes from a confusion of what should be the minimal backlog. It is
pretty clear it is not 64KB or whatever max GSO packet ever reached the
qdisc.
codel intent was to use MTU of the device.
After the fix, we finally drop some packets, and rtt/cwnd of my single
TCP flow are meeting our expectations.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Kathleen Nichols <nichols@pollere.com> Cc: Dave Taht <dave.taht@gmail.com> Cc: Van Jacobson <vanj@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use ieee80211_vif pointer in ath_get_rate_txpower() since it has been
overwritten by setup_frame_info() and it will result in a corrupted tx power
configuration. Set per-packet tx power in setup_frame_info() according to
current vif tx power.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Sun, 3 May 2015 20:53:02 +0000 (23:53 +0300)]
Merge tag 'iwlwifi-for-kalle-2015-04-28' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)
1) Receive packet length needs to be adjust by 2 on RX to accomodate
the two padding bytes in altera_tse driver. From Vlastimil Setka.
2) If rx frame is dropped due to out of memory in macb driver, we leave
the receive ring descriptors in an undefined state. From Punnaiah
Choudary Kalluri
3) Some netlink subsystems erroneously signal NLM_F_MULTI. That is
only for dumps. Fix from Nicolas Dichtel.
4) Fix mis-use of raw rt->rt_pmtu value in ipv4, one must always go via
the ipv4_mtu() helper. From Herbert Xu.
5) Fix null deref in bridge netfilter, and miscalculated lengths in
jump/goto nf_tables verdicts. From Florian Westphal.
6) Unhash ping sockets properly.
7) Software implementation of BPF divide did 64/32 rather than 64/64
bit divide. The JITs got it right. Fix from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
ipv4: Missing sk_nulls_node_init() in ping_unhash().
net: fec: Fix RGMII-ID mode
net/mlx4_en: Schedule napi when RX buffers allocation fails
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
net/mlx4_core: Fix unaligned accesses
mlx4_en: Use correct loop cursor in error path.
cxgb4: Fix MC1 memory offset calculation
bnx2x: Delay during kdump load
net: Fix Kernel Panic in bonding driver debugfs file: rlb_hash_table
net: dsa: Fix scope of eeprom-length property
net: macb: Fix race condition in driver when Rx frame is dropped
hv_netvsc: Fix a bug in netvsc_start_xmit()
altera_tse: Correct rx packet length
mlx4: Fix tx ring affinity_mask creation
tipc: fix problem with parallel link synchronization mechanism
tipc: remove wrong use of NLM_F_MULTI
bridge/nl: remove wrong use of NLM_F_MULTI
bridge/mdb: remove wrong use of NLM_F_MULTI
net: sched: act_connmark: don't zap skb->nfct
trivial: net: systemport: bcmsysport.h: fix 0x0x prefix
...
David S. Miller [Sat, 2 May 2015 02:02:47 +0000 (22:02 -0400)]
ipv4: Missing sk_nulls_node_init() in ping_unhash().
If we don't do that, then the poison value is left in the ->pprev
backlink.
This can cause crashes if we do a disconnect, followed by a connect().
Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Wen Xu <hotdog3645@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When we end I/O struct request with error, we need to pass
obj_request->length as @nr_bytes so that the entire obj_request worth
of bytes is completed. Otherwise block layer ends up confused and we
trip on
in rbd_img_obj_callback() due to more being true no matter what. We
already do it in most cases but we are missing some, in particular
those where we don't even get a chance to submit any obj_requests, due
to an early -ENOMEM for example.
A number of obj_request->xferred assignments seem to be redundant but
I haven't touched any of obj_request->xferred stuff to keep this small
and isolated.
Cc: Alex Elder <elder@linaro.org> Cc: stable@vger.kernel.org # 3.10+ Reported-by: Shawn Edwards <lesser.evil@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Linus Torvalds [Fri, 1 May 2015 14:46:21 +0000 (07:46 -0700)]
Merge branch 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"A few more btrfs fixes.
These range from corners Filipe found in the new free space cache
writeback to a grab bag of fixes from the list"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: btrfs_release_extent_buffer_page didn't free pages of dummy extent
Btrfs: fill ->last_trans for delayed inode in btrfs_fill_inode.
btrfs: unlock i_mutex after attempting to delete subvolume during send
btrfs: check io_ctl_prepare_pages return in __btrfs_write_out_cache
btrfs: fix race on ENOMEM in alloc_extent_buffer
btrfs: handle ENOMEM in btrfs_alloc_tree_block
Btrfs: fix find_free_dev_extent() malfunction in case device tree has hole
Btrfs: don't check for delalloc_bytes in cache_save_setup
Btrfs: fix deadlock when starting writeback of bg caches
Btrfs: fix race between start dirty bg cache writeout and bg deletion
Linus Torvalds [Fri, 1 May 2015 14:44:32 +0000 (07:44 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Not too much here, but we've addressed a couple of nasty issues in the
dma-mapping code as well as adding the halfword and byte variants of
load_acquire/store_release following on from the CSD locking bug that
you fixed in the core.
- fix perf devicetree warnings at probe time
- fix memory leak in __dma_free()
- ensure DMA buffers are always zeroed
- show IRQ trigger in /proc/interrupts (for parity with ARM)
- implement byte and halfword access for smp_{load_acquire,store_release}"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: perf: Fix the pmu node name in warning message
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
arm64: add missing PAGE_ALIGN() to __dma_free()
arm64: dma-mapping: always clear allocated buffers
ARM64: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
arm64: add missing data types in smp_load_acquire/smp_store_release
Using IDR_SRR in RXFIFO_ID to test for the presence of data is only
valid for standard frames. For extended frames the bit is always 1 and
IDR_RTR should be used instead. This patch switches the check to use
CAN_RTR_FLAG which is correctly set when reading the ID.
The patch also changes the DW1/DW2 to be read unconditionally, since
this is necessary to remove the frame from the RXFIFO.
Merge tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Three regression fixes this time, one for a recent regression in the
cpuidle core affecting multiple systems, one for an inadvertently
added duplicate typedef in ACPICA that breaks compilation with GCC 4.5
and one for an ACPI Smart Battery Subsystem driver regression
introduced during the 3.18 cycle (stable-candidate).
Specifics:
- Fix for a regression in the cpuidle core introduced by one of the
recent commits in the clockevents_notify() removal series that put
a call to a function which had to be executed with disabled
interrupts into a code path running with enabled interrupts (Rafael
J Wysocki)
- Fix for a build problem in ACPICA (with GCC 4.5) introduced by one
of the recent ACPICA tools commits that added a duplicate typedef
to one of the ACPICA's header files by mistake (Olaf Hering)
- Fix for a regression in the ACPI SBS (Smart Battery Subsystem)
driver introduced during the 3.18 development cycle causing the
smart battery manager to be marked as not present when it should be
marked as present (Chris Bainbridge)"
* tag 'pm+acpi-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Run tick_broadcast_exit() with disabled interrupts
ACPI / SBS: Enable battery manager when present
ACPICA: remove duplicate u8 typedef
Merge tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"One nice fix is Peter's patch to make the old good SB Audigy PCI to
work with 32bit DMA instead of 31bit. This allows the MIDI synth
running on modern machines again. Along with it, a few fixes for
emu10k1 have merged.
In ASoC side, there is one fix in the common code, but it's just
trivial additions of static inline functions for CONFIG_PM=n. The
rest are various device-specific small fixes.
Last but not least, a few HD-audio fixes are included, as usual, too"
* tag 'sound-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ASoC: rt5677: fixed wrong DMIC ref clock
ALSA: emu10k1: Emu10k2 32 bit DMA mode
ALSA: emux: Fix mutex deadlock in OSS emulation
ASoC: Update email-id of Rajeev Kumar
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ALSA: hda - Fix missing va_end() call in snd_hda_codec_pcm_new()
ALSA: emux: Fix mutex deadlock at unloading
ALSA: emu10k1: Fix card shortname string buffer overflow
ALSA: hda - Add mute-LED mode control to Thinkpad
ALSA: hda - Fix mute-LED fixed mode
ALSA: hda - Fix click noise at start on Dell XPS13
ASoC: rt5645: Add ACPI match ID
ASoC: rt5677: add register patch for PLL
ASoC: Intel: fix the makefile for atom code
ASoC: dapm: Enable autodisable on SOC_DAPM_SINGLE_TLV_AUTODISABLE
ASoC: add static inline funcs to fix a compiling issue
ASoC: Intel: sst_byt: remove kfree for memory allocated with devm_kzalloc
ASoC: samsung: s3c24xx-i2s: Fix return value check in s3c24xx_iis_dev_probe()
ASoC: tfa9879: Fix return value check in tfa9879_i2c_probe()
ASoC: fsl_ssi: Fix platform_get_irq() error handling
...
net/mlx4_en: Schedule napi when RX buffers allocation fails
When system is out of memory, refilling of RX buffers fails while
the driver continue to pass the received packets to the kernel stack.
At some point, when all RX buffers deplete, driver may fall into a
sleep, and not recover when memory for new RX buffers is once again
availible. This is because hardware does not have valid descriptors,
so no interrupt will be generated for the driver to return to work
in napi context. Fix it by schedule the napi poll function from
stats_task delayed workqueue, as long as the allocations fail.
Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Thu, 30 Apr 2015 11:51:27 +0000 (07:51 -0400)]
netxen_nic: use spin_[un]lock_bh around tx_clean_lock
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Wed, 29 Apr 2015 22:59:35 +0000 (15:59 -0700)]
mlx4_en: Use correct loop cursor in error path.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Fixes: 279eeaf ("net/mlx4_en: Use affinity hint") Acked-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'asoc-v4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.1
A few fixes for v4.1, none earth shattering and mostly driver related
except for one change to fix !PM builds for Intel platforms which is
done by adding stubs in the core so other platforms don't run into the
same issue.
Alexander Aring [Thu, 30 Apr 2015 15:45:02 +0000 (17:45 +0200)]
at86rf230: change state change if from trx_off
If a transmit ends in a calibration which means the transceiver do a
TRX_OFF state change, we can directly change into TX_ARET state instead
doing a TX_ON to TX_ARET statechange.
Alexander Aring [Thu, 30 Apr 2015 15:45:01 +0000 (17:45 +0200)]
at86rf230: remove unnecessary tx state change
All supported transceivers can do a valid state change from TRX_OFF to
AACK_ON. This patch removes the state change chain from TRX_OFF ->
TX_ON -> AACK_ON instead we doing a directly state change from TRX_OFF
to AACK_ON.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alexander Aring [Thu, 30 Apr 2015 15:44:59 +0000 (17:44 +0200)]
at86rf230: move cal_timeout to state change
This patch moves the calculation timeout of TRX_OFF to RX_AACK_ON
handling to the async state change functionality. With this patch we can
do a reset of calculation timeout when others TRX_OFF to RX_AACK_ON
happens instead of doing this on interface up only.
cfg802154: pass name_assign_type to rdev_add_virtual_intf()
This code is based on commit 0cef6b0d6c703
("cfg80211: pass name_assign_type to rdev_add_virtual_intf()")
This will expose in sysfs whether the ifname of a IEEE-802.15.4
device is set by userspace or generated by the kernel.
We are using two types of name_assign_types
o NET_NAME_ENUM: Default interface name provided by kernel
o NET_NAME_USER: Interface name provided by user.
mac802154: llsec: fix return value check in llsec_key_alloc()
In case of error, the functions crypto_alloc_aead() and crypto_alloc_blkcipher()
returns ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Currently if ieee802154_if_add failed, we don't unregister the wpan phy
which was registered before. This patch adds a correct error handling
for unregister the wpan phy when ieee802154_if_add failed.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Skip the shutdown routine if the interface is not up
Most likely, the shutdown routine requires the interface to be up.
This is the case for BTUSB_INTEL: the routine tries to send a command
to the interface, but since this one is down, it fails and exits once
HCI_INIT_TIMEOUT has expired.
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm changes from Paolo Bonzini:
"Remove from guest code the handling of task migration during a pvclock
read; instead use the correct protocol in KVM.
This removes the need for task migration notifiers in core scheduler
code"
[ The scheduler people really hated the migration notifiers, so this was
kind of required - Linus ]
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86: pvclock: Really remove the sched notifier for cross-cpu migrations
kvm: x86: fix kvmclock update protocol
Merge tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper bugfixes from Mike Snitzer:
"Fix two bugs in the request-based DM blk-mq support that was added
during the 4.1 merge"
* tag 'dm-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
dm: only initialize the request_queue once
Merge tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.1-rc2.
They include some minor fixes that resolve reported issues, and a new
device quirk.
All have been in linux-next succesfully"
* tag 'tty-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add support for 16 port Exar boards
serial: samsung: fix serial console break
tty/serial: at91: maxburst was missing for dma transfers
serial: of-serial: Remove device_type = "serial" registration
serial: xilinx: Use platform_get_irq to get irq description structure
serial: core: Fix kernel-doc build warnings
tty: Re-add external interface for tty_set_termios()
Merge tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully"
* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
cdc-acm: prevent infinite loop when parsing CDC headers.
Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
usb: chipidea: otg: remove mutex unlock and lock while stop and start role
uas: Set max_sectors_240 quirk for ASM1053 devices
uas: Add US_FL_MAX_SECTORS_240 flag
uas: Allow uas_use_uas_driver to return usb-storage flags
Merge tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver updates from Simon Horman:
- remove test for now unsupported sh7372 SoC
- disable PM runtime for multi-platform r8a73a4 and sh73a0 SoCs with
genpd
* tag 'renesas-sh-drivers-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
drivers: sh: Remove test for now unsupported sh7372
drivers: sh: Disable PM runtime for multi-platform r8a73a4 with genpd
drivers: sh: Disable PM runtime for multi-platform sh73a0 with genpd
Mike Snitzer [Wed, 29 Apr 2015 14:48:09 +0000 (10:48 -0400)]
dm: fix free_rq_clone() NULL pointer when requeueing unmapped request
Commit 90849e59b1 ("dm: optimize dm_mq_queue_rq to _not_ use kthread if
using pure blk-mq") mistakenly removed free_rq_clone()'s clone->q check
before testing clone->q->mq_ops. It was an oversight to discontinue
that check for 1 of the 2 use-cases for free_rq_clone():
1) free_rq_clone() called when an unmapped original request is requeued
2) free_rq_clone() called in the request-based IO completion path
The clone->q check made sense for case #1 but not for #2. However, we
cannot just reinstate the check as it'd mask a serious bug in the IO
completion case #2 -- no in-flight request should have an uninitialized
request_queue (basic block layer refcounting _should_ ensure this).
The NULL pointer seen for case #1 is detailed here:
https://www.redhat.com/archives/dm-devel/2015-April/msg00160.html
Fix this free_rq_clone() NULL pointer by simply checking if the
mapped_device's type is DM_TYPE_MQ_REQUEST_BASED (clone's queue is
blk-mq) rather than checking clone->q->mq_ops. This avoids the need to
dereference clone->q, but a WARN_ON_ONCE is added to let us know if an
uninitialized clone request is being completed.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 347192a20b ("dm: add full blk-mq support to request-based DM")
didn't properly account for the need to short-circuit re-initializing
DM's blk-mq request_queue if it was already initialized.
Otherwise, reloading a blk-mq request-based DM table (either manually
or via multipathd) resulted in errors, see:
https://www.redhat.com/archives/dm-devel/2015-April/msg00132.html
Fix is to only initialize the request_queue on the initial table load
(when the mapped_device type is assigned).
This is better than having dm_init_request_based_blk_mq_queue() return
early if the queue was already initialized because it elevates the
constraint to a more meaningful location in DM core. As such the
pre-existing early return in dm_init_request_based_queue() can now be
removed.
Fixes: 347192a20b ("dm: add full blk-mq support to request-based DM") Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
arm64: perf: Fix the pmu node name in warning message
With commit ab44aaf640ad ("arm64: pmu: add support for interrupt-affinity
property"), we print a warning when we find a PMU SPI with a missing
missing interrupt-affinity property in a pmu node. Unfortunately, we
pass the wrong (NULL) device node to of_node_full_name, resulting in
unhelpful messages such as:
hw perfevents: Failed to parse <no-node>/interrupt-affinity[0]
This patch fixes the name to that of the pmu node.
Fixes: ab44aaf640ad (arm64: pmu: add support for interrupt-affinity property) Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Will Deacon [Fri, 17 Apr 2015 13:41:29 +0000 (14:41 +0100)]
arm64: perf: don't warn about missing interrupt-affinity property for PPIs
PPIs are affine by nature, so the interrupt-affinity property is not
used and therefore we shouldn't print a warning in its absence.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Daniel Drake [Thu, 16 Apr 2015 20:09:55 +0000 (14:09 -0600)]
Bluetooth: btusb: Add Realtek 8723A/8723B/8761A/8821A support
Realtek ship a variety of bluetooth USB devices that identify
themselves with standard USB Bluetooth device class values, but
require a special driver to actually work. Without that driver,
you never get any scan results.
More recently however, Realtek appear to have wisened up and simply
posted a firmware update that makes these devices comply with
normal btusb protocols. The firmware needs to be uploaded on each boot.
Based on Realtek code from https://github.com/lwfinger/rtl8723au_bt
('new' branch).
This enables bluetooth support in the Gigabyte Brix GB-BXBT-2807 which
has this RTL8723BE USB device:
Bluetooth: hci_uart: Reorder Atheros specific driver callbacks
The driver callbacks in the Atheros support were all in a random order
and did not help readability of this driver. So reorder them to make
them aligned with what other Bluetooth UART drivers do. This patch is
not changing any actual code.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
projects / kernel.git / log