David Milburn [Tue, 14 Nov 2017 22:17:25 +0000 (16:17 -0600)]
libata: sata_down_spd_limit should return if driver has not recorded sstatus speed
During hotplug, it is possible for 6Gbps link speed to be limited all
the way down to 1.5 Gbps which may lead to a slower link speed when
drive is re-connected.
This behavior has been seen on a Intel Lewisburg SATA controller
(8086:a1d2) with HGST HUH728080ALE600 drive where SATA link speed was
limited to 1.5 Gbps and when re-connected the link came up 3.0 Gbps.
This patch was retested on above configuration and showed the
hotplugged link to come back online at max speed (6Gbps). I did not
see the downgrade when testing on Intel C600/X79, but retested patched
linux-4.14-rc5 kernel and didn't see any side effects from this
change. Also, successfully retested hotplug on port multiplier 3Gbps
link.
tj: Minor comment updates.
Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
The driver name "ahci" is already used by the ahci platform driver.
This leads to the following error:
Error: Driver 'ahci' is already registered, aborting...
Yuantian Tang [Mon, 4 Dec 2017 09:01:20 +0000 (17:01 +0800)]
ahci: qoriq: refine port register configuration
These PP2C and PP3C registers control the configuration of the PHY
control OOB timing for the COMINIT/COMWAKE parameters respectively
for sata port. Overwrite default values with calculated ones to get
better OOB timing.
Linus Torvalds [Sun, 26 Nov 2017 23:03:49 +0000 (15:03 -0800)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Linus Torvalds [Sun, 26 Nov 2017 22:39:20 +0000 (14:39 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Glexiner:
- unbreak the irq trigger type check for legacy platforms
- a handful fixes for ARM GIC v3/4 interrupt controllers
- a few trivial fixes all over the place
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
irqchip/exiu: Fix return value check in exiu_init()
irqchip/gic-v3-its: Remove artificial dependency on PCI
irqchip/gic-v4: Add forward definition of struct irq_domain_ops
irqchip/gic-v3: pr_err() strings should end with newlines
irqchip/s3c24xx: pr_err() strings should end with newlines
irqchip/gic-v3: Fix ppi-partitions lookup
irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
genirq: Track whether the trigger type has been set
Linus Torvalds [Sun, 26 Nov 2017 22:11:54 +0000 (14:11 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
Linus Torvalds [Sun, 26 Nov 2017 21:43:25 +0000 (13:43 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a documentation fix, a Sparse warning fix and a debugging
fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix task state recording/printout
sched/deadline: Don't use dubious signed bitfields
sched/deadline: Fix the description of runtime accounting in the documentation
Linus Torvalds [Sun, 26 Nov 2017 21:41:48 +0000 (13:41 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: two PMU driver fixes and a memory leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix memory leak triggered by perf --namespace
perf/x86/intel/uncore: Add event constraint for BDX PCU
perf/x86/intel: Hide TSX events when RTM is not supported
Linus Torvalds [Sun, 26 Nov 2017 21:11:18 +0000 (13:11 -0800)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"A handful of objtool fixes, most of them related to making the UAPI
header-syncing warnings easier to read and easier to act upon"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/headers: Sync objtool UAPI header
objtool: Fix cross-build
objtool: Move kernel headers/code sync check to a script
objtool: Move synced files to their original relative locations
objtool: Make unreachable annotation inline asms explicitly volatile
objtool: Add a comment for the unreachable annotation macros
Russell King [Fri, 24 Nov 2017 23:49:34 +0000 (23:49 +0000)]
ARM: BUG if jumping to usermode address in kernel mode
Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode. This
could occur due to corrupted stack state, which has been observed with
"ftracetest".
This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Linus Torvalds [Sat, 25 Nov 2017 18:21:54 +0000 (08:21 -1000)]
Merge tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- more changes for HS48 cores: supporting MMUv5, detecting new
micro-arch gizmos
- axs10x platform wiring up reset driver merged in this cycle
- ARC perf driver optimizations
* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: perf: avoid vmalloc backed mmap
ARCv2: perf: optimize given that num counters <= 32
ARCv2: perf: tweak overflow interrupt
ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the ISA config
Linus Torvalds [Sat, 25 Nov 2017 18:06:30 +0000 (08:06 -1000)]
Merge tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- use 'pwd' instead of '/bin/pwd' for portability
- clean up Makefiles
- fix ld-option for clang
- fix malloc'ed data size in Kconfig
- fix parallel building along with coccicheck
- fix a minor issue of package building
- prompt to use "rpm-pkg" instead of "rpm"
- clean up *.i and *.lst patterns by "make clean"
* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: drop $(extra-y) from real-objs-y
kbuild: clean up *.i and *.lst patterns by make clean
kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
kbuild: pkg: use --transform option to prefix paths in tar
coccinelle: fix parallel build with CHECK=scripts/coccicheck
kconfig/symbol.c: use correct pointer type argument for sizeof
kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
kbuild: remove all dummy assignments to obj-
kbuild: create built-in.o automatically if parent directory wants it
kbuild: /bin/pwd -> pwd
Linus Torvalds [Sat, 25 Nov 2017 17:58:25 +0000 (07:58 -1000)]
Merge tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Make AFS file locking work again.
- Don't write to a page that's being written out, but wait for it to
complete.
- Do d_drop() and d_add() in the right places.
- Put keys on error paths.
- Remove some redundant code.
* tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: remove redundant assignment of dvnode to itself
afs: cell: Remove unnecessary code in afs_lookup_cell
afs: Fix signal handling in some file ops
afs: Fix some dentry handling in dir ops and missing key_puts
afs: Make afs_write_begin() avoid writing to a page that's being stored
afs: Fix file locking
Linus Torvalds [Sat, 25 Nov 2017 05:44:25 +0000 (19:44 -1000)]
Merge tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"Trimmed second batch of KVM changes for Linux 4.15:
- GICv4 Support for KVM/ARM
- re-introduce support for CPUs without virtual NMI (cc stable) and
allow testing of KVM without virtual NMI on available CPUs
- fix long-standing performance issues with assigned devices on AMD
(cc stable)"
* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
kvm: vmx: Allow disabling virtual NMI support
kvm: vmx: Reinstate support for CPUs without virtual NMI
KVM: SVM: obey guest PAT
KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
KVM: arm/arm64: Fix GICv4 ITS initialization issues
KVM: arm/arm64: GICv4: Theory of operations
KVM: arm/arm64: GICv4: Enable VLPI support
KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
KVM: arm/arm64: GICv4: Add doorbell interrupt handling
KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
...
Linus Torvalds [Sat, 25 Nov 2017 05:40:12 +0000 (19:40 -1000)]
Merge tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A small batch of fixes, about 50% tagged for stable and the rest for
recently merged code.
There's one more fix for the >128T handling on hash. Once a process
had requested a single mmap above 128T we would then always search
above 128T. The correct behaviour is to consider the hint address in
isolation for each mmap request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
identify P9 DD2.1 but in code that is currently not used by default.
* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
powerpc/perf: Fix IMC_MAX_PMU macro
powerpc/perf: Fix pmu_count to count only nest imc pmus
powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
powerpc/vas: Export chip_to_vas_id()
powerpc/64s/slice: Use addr limit when computing slice mask
Linus Torvalds [Sat, 25 Nov 2017 05:19:20 +0000 (19:19 -1000)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This series is predominantly bug-fixes, with a few small improvements
that have been outstanding over the last release cycle.
As usual, the associated bug-fixes have CC' tags for stable.
Also, things have been particularly quiet wrt new developments the
last months, with most folks continuing to focus on stability atop 4.x
stable kernels for their respective production configurations.
Also at this point, the stable trees have been synced up with
mainline. This will continue to be a priority, as production users
tend to run exclusively atop stable kernels, a few releases behind
mainline.
- Fix quiese during transport_write_pending_qf endless loop (nab)
- Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
(Don White + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
tcmu: Add a missing unlock on an error path
tcmu: Fix some memory corruption
iscsi-target: Fix non-immediate TMR reference leak
iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
target: Fix quiese during transport_write_pending_qf endless loop
target: Fix caw_sem leak in transport_generic_request_failure
target: Fix QUEUE_FULL + SCSI task attribute handling
iSCSI-target: Use common error handling code in iscsi_decode_text_input()
target/iscsi: Detect conn_cmd_list corruption early
target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
target/iscsi: Fix endianness in an error message
target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
target/iscsi: Define OFFLOAD_BUF_SIZE once
target: Inline transport_put_cmd()
target: Suppress gcc 7 fallthrough warnings
target: Move a declaration of a global variable into a header file
tcmu: fix double se_cmd completion
target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
...
Colin Ian King [Mon, 20 Nov 2017 13:58:20 +0000 (13:58 +0000)]
afs: remove redundant assignment of dvnode to itself
The assignment of dvnode to itself is redundant and can be removed.
Cleans up warning detected by cppcheck:
fs/afs/dir.c:975: (warning) Redundant assignment of 'dvnode' to itself.
Fixes: 4ead43a3559d ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 20 Nov 2017 22:41:00 +0000 (22:41 +0000)]
afs: Fix signal handling in some file ops
afs_mkdir(), afs_create(), afs_link() and afs_symlink() all need to drop
the target dentry if a signal causes the operation to be killed immediately
before we try to contact the server.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 20 Nov 2017 23:04:08 +0000 (23:04 +0000)]
afs: Fix some dentry handling in dir ops and missing key_puts
Fix some of dentry handling in AFS directory ops:
(1) Do d_drop() on the new_dentry before assigning a new inode to it in
afs_vnode_new_inode(). It's fine to do this before calling afs_iget()
because the operation has taken place on the server.
(2) Replace d_instantiate()/d_rehash() with d_add().
(3) Don't d_drop() the new_dentry in afs_rename() on error.
Also fix afs_link() and afs_rename() to call key_put() on all error paths
where the key is taken.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Sat, 18 Nov 2017 00:13:30 +0000 (00:13 +0000)]
afs: Make afs_write_begin() avoid writing to a page that's being stored
Make afs_write_begin() wait for a page that's marked PG_writeback because:
(1) We need to avoid interference with the data being stored so that the
data on the server ends up in a defined state.
(2) page->private is used to track the window of dirty data within a page,
but it's also used by the storage code to track what's being written,
being cleared by the completion notification. Ownership can't be
relinquished by the storage code until completion because it a store
fails, the data must be remarked dirty.
Tracing shows something like the following (edited):
The clear (completion) corresponding to the store+ (store continuation from
a previous page) happens between the second begin (afs_write_begin) and the
store corresponding to that. This results in the second store not seeing
any data to write back, leading to the following warning:
Thomas Gleixner [Wed, 22 Nov 2017 12:05:48 +0000 (13:05 +0100)]
sched/debug: Fix task state recording/printout
The recent conversion of the task state recording to use task_state_index()
broke the sched_switch tracepoint task state output.
task_state_index() returns surprisingly an index (0-7) which is then
printed with __print_flags() applying bitmasks. Not really working and
resulting in weird states like 'prev_state=t' instead of 'prev_state=I'.
Use TASK_REPORT_MAX instead of TASK_STATE_MAX to report preemption. Build a
bitmask from the return value of task_state_index() and store it in
entry->prev_state, which makes __print_flags() work as expected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: stable@vger.kernel.org Fixes: 56fc8c129e3a ("sched/tracing: Fix trace_sched_switch task-state printing") Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1711221304180.1751@nanos Signed-off-by: Ingo Molnar <mingo@kernel.org>
Masami Hiramatsu [Fri, 24 Nov 2017 04:56:30 +0000 (13:56 +0900)]
x86/decoder: Add new TEST instruction pattern
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c
Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked 1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
1) Fix PCI IDs of 9000 series iwlwifi devices, from Luca Coelho.
2) bpf offload bug fixes from Jakub Kicinski.
3) Fix bpf verifier to NOP out code which is dead at run time because
due to branch pruning the verifier will not explore such
instructions. From Alexei Starovoitov.
4) Fix crash when deleting secondary chains in packet scheduler
classifier. From Roman Kapl.
5) Fix buffer management bugs in smc, from Ursula Braun.
6) Fix regression in anycast route handling, from David Ahern.
7) Fix link settings regression in r8169, from Tobias Jakobi.
8) Add back enough UFO support so that live migration still works, from
Willem de Bruijn.
9) Linearize enough packet data for the full extent to which the ipvlan
code will inspect the packet headers, from Gao Feng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
ipvlan: Fix insufficient skb linear check for ipv6 icmp
ipvlan: Fix insufficient skb linear check for arp
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
net: accept UFO datagrams from tuntap and packet
net: realtek: r8169: implement set_link_ksettings()
net: ipv6: Fixup device for anycast routes during copy
net/smc: Fix preinitialization of buf_desc in __smc_buf_create()
net/smc: use sk_rcvbuf as start for rmb creation
ipv6: Do not consider linkdown nexthops during multipath
net: sched: fix crash when deleting secondary chains
net: phy: cortina: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
bpf: fix branch pruning logic
bpf: change bpf_perf_event_output arg5 type to ARG_CONST_SIZE_OR_ZERO
bpf: change bpf_probe_read_str arg2 type to ARG_CONST_SIZE_OR_ZERO
bpf: remove explicit handling of 0 for arg2 in bpf_probe_read
bpf: introduce ARG_PTR_TO_MEM_OR_NULL
i40evf: Use smp_rmb rather than read_barrier_depends
fm10k: Use smp_rmb rather than read_barrier_depends
igb: Use smp_rmb rather than read_barrier_depends
...
Linus Torvalds [Fri, 24 Nov 2017 07:14:30 +0000 (21:14 -1000)]
Merge tag 'platform-drivers-x86-v4.15-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix two issues resulting from the dell-smbios refactoring and
introduction of the dell-smbios-wmi dispatcher.
The first ensures a proper error code is returned when kzalloc fails.
The second avoids an issue in older Dell BIOS implementations which
would fail if the more complex calls were made by limiting those
platforms to the simple calls such as those used by the existing
dell-laptop and dell-wmi drivers, preserving their functionality prior
to the addition of the dell-smbios-wmi dispatcher"
* tag 'platform-drivers-x86-v4.15-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-laptop: fix error return code in dell_init()
platform/x86: dell-smbios-wmi: Disable userspace interface if missing hotfix
Linus Torvalds [Fri, 24 Nov 2017 07:12:58 +0000 (21:12 -1000)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two basic fixes: one for the sparse problem with the blacklist flags
and another for a hang forever in bnx2i"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Use 'blist_flags_t' for scsi_devinfo flags
scsi: bnx2fc: Fix hung task messages when a cleanup response is not received during abort
- Missing help text for the recent Intel SST kconfig change"
* tag 'sound-fix-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: Add Raven PCI ID
ALSA: hda/realtek - Fix ALC700 family no sound issue
ALSA: hda - Fix yet remaining issue with vmaster 0dB initialization
ALSA: usb-audio: Add sanity checks in v2 clock parsers
ALSA: usb-audio: Fix potential zero-division at parsing FU
ALSA: usb-audio: Fix potential out-of-bound access at parsing SU
ALSA: usb-audio: Add sanity checks to FE parser
ALSA: timer: Remove kernel warning at compat ioctl error paths
ALSA: pcm: update tstamp only if audio_tstamp changed
ALSA: hda/realtek: Add headset mic support for Intel NUC Skull Canyon
ALSA: hda: Fix too short HDMI/DP chmap reporting
ALSA: usb-audio: uac1: Invalidate ctl on interrupt
ALSA: hda/realtek - Fix ALC275 no sound issue
ASoC: Intel: Add help text for SND_SOC_INTEL_SST_TOPLEVEL
Linus Torvalds [Fri, 24 Nov 2017 07:04:56 +0000 (21:04 -1000)]
Merge tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"Fixes/cleanups for rc1, non-desktop flags for VR
- remove the MSM dt-bindings file Rob managed to push in the previous
pull.
- add a property/edid quirk to denote HMD devices, I had these
hanging around for a few weeks and Keith had done some work on
them, they are fairly self contained and small, and only affect
people using HTC Vive VR headsets so far.
- amdgpu, tegra, tilcdc, fsl fixes
- some imx-drm cleanups I missed, these seemed pretty small, and no
reason to hold off.
I have one TTM regression fix (fixes bochs-vga in qemu) sitting
locally awaiting review I'll probably send that in a separate pull
request tomorrow"
* tag 'drm-for-v4.15-part2' of git://people.freedesktop.org/~airlied/linux: (33 commits)
dt-bindings: remove file that was added accidentally
drm/edid: quirk HTC vive headset as non-desktop. [v2]
drm/fb: add support for not enabling fbcon on non-desktop displays [v2]
drm: add connector info/property for non-desktop displays [v2]
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
drm/tilcdc: Remove obsolete "ti,tilcdc,slave" dts binding support
drm/tegra: sor: Reimplement pad clock
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
drm/amd/pp: fix dpm randomly failed on Vega10
drm/amdgpu: set f_mapping on exported DMA-bufs
drm/amdgpu: Properly allocate VM invalidate eng v2
drm/fsl-dcu: enable IRQ before drm_atomic_helper_resume()
drm/fsl-dcu: avoid disabling pixel clock twice on suspend
...
Linus Torvalds [Fri, 24 Nov 2017 07:01:32 +0000 (21:01 -1000)]
Merge tag 'docs-4.15-2' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A few late-arriving docs updates that have no real reason to wait.
There's a new "Co-Developed-by" tag described by Greg, and a build
enhancement from Willy to generate docs warnings during a kernel build
(but only when additional warnings have been requested in general)"
* tag 'docs-4.15-2' of git://git.lwn.net/linux:
Add optional check for bad kernel-doc comments
Documentation: fix profile= options in kernel-parameters.txt
documentation/svga.txt: update outdated file
kokr/memory-barriers.txt: Fix typo in paring example
kokr/memory-barriers/txt: Replace uses of "transitive"
Documentation/process: add Co-Developed-by: tag for patches with multiple authors
Linus Torvalds [Fri, 24 Nov 2017 06:51:27 +0000 (20:51 -1000)]
Merge branch 'next-keys' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull keys update from James Morris:
"There's nothing too controversial here:
- Doc fix for keyctl_read().
- time_t -> time64_t replacement.
- Set the module licence on things to prevent tainting"
* 'next-keys' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
pkcs7: Set the module licence to prevent tainting
security: keys: Replace time_t with time64_t for struct key_preparsed_payload
security: keys: Replace time_t/timespec with time64_t
KEYS: fix in-kernel documentation for keyctl_read()
Bug Fixes:
- initialized returned struct aa_perms
- fix leak of null profile name if profile allocation fails
- ensure that undecidable profile attachments fail
- fix profile attachment for special unconfined profiles
- fix locking when creating a new complain profile.
- fix possible recursive lock warning in __aa_create_ns"
* tag 'apparmor-pr-2017-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: fix possible recursive lock warning in __aa_create_ns
apparmor: fix locking when creating a new complain profile.
apparmor: fix profile attachment for special unconfined profiles
apparmor: ensure that undecidable profile attachments fail
apparmor: fix leak of null profile name if profile allocation fails
apparmor: remove unused redundant variable stop
apparmor: Fix bool initialization/comparison
apparmor: initialized returned struct aa_perms
apparmor: fix spelling mistake: "resoure" -> "resource"
Bjorn Helgaas [Wed, 22 Nov 2017 22:13:37 +0000 (16:13 -0600)]
x86/PCI: Remove unused HyperTransport interrupt support
There are no in-tree callers of ht_create_irq(), the driver interface for
HyperTransport interrupts, left. Remove the unused entry point and all the
supporting code.
See 19333e7d8bdc ("[PATCH] Initial generic hypertransport interrupt
support").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-pci@vger.kernel.org Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Link: https://lkml.kernel.org/r/20171122221337.3877.23362.stgit@bhelgaas-glaptop.roam.corp.google.com
Borislav Petkov [Thu, 23 Nov 2017 09:19:51 +0000 (10:19 +0100)]
x86/umip: Fix insn_get_code_seg_params()'s return value
In order to save on redundant structs definitions
insn_get_code_seg_params() was made to return two 4-bit values in a char
but clang complains:
arch/x86/lib/insn-eval.c:780:10: warning: implicit conversion from 'int' to 'char'
changes value from 132 to -124 [-Wconstant-conversion]
return INSN_CODE_SEG_PARAMS(4, 8);
~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~
./arch/x86/include/asm/insn-eval.h:16:57: note: expanded from macro 'INSN_CODE_SEG_PARAMS'
#define INSN_CODE_SEG_PARAMS(oper_sz, addr_sz) (oper_sz | (addr_sz << 4))
Those two values do get picked apart afterwards the opposite way of how
they were ORed so wrt to the LSByte, the return value is the same.
But this function returns -EINVAL in the error case, which is an int. So
make it return an int which is the native word size anyway and thus fix
the clang warning.
Reported-by: Kees Cook <keescook@google.com> Reported-by: Nick Desaulniers <nick.desaulniers@gmail.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: ricardo.neri-calderon@linux.intel.com Link: https://lkml.kernel.org/r/20171123091951.1462-1-bp@alien8.de
Chao Fan [Thu, 23 Nov 2017 09:08:47 +0000 (17:08 +0800)]
x86/boot/KASLR: Remove unused variable
There are two variables "rc" in mem_avoid_memmap. One at the top of the
function and another one inside the while() loop. Drop the outer one as it
is unused. Cleanup some whitespace damage while at it.
Kees Cook [Wed, 22 Nov 2017 20:56:45 +0000 (12:56 -0800)]
genirq/matrix: Make - vs ?: Precedence explicit
Noticed with a Clang build. This improves the readability of the ?:
expression, as it has lower precedence than the - expression. Show
explicitly that - is evaluated first.
Colin Ian King [Fri, 17 Nov 2017 18:35:53 +0000 (18:35 +0000)]
irqchip/qcom: Fix u32 comparison with value less than zero
The comparison of u32 nregs being less than zero is never true since
nregs is unsigned. Fix this by making nregs a signed integer.
Fixes: 7e2a12798c80 ("irqchip/qcom: Add IRQ combiner driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: kernel-janitors@vger.kernel.org Cc: Jason Cooper <jason@lakedaemon.net> Link: https://lkml.kernel.org/r/20171117183553.2739-1-colin.king@canonical.com
====================
ipvlan: Fix insufficient skb linear check
The current ipvlan codes use pskb_may_pull to get the skb linear header in
func ipvlan_get_L3_hdr, but the size isn't enough for arp and ipv6 icmp.
So it may access the unexpected momory in ipvlan_addr_lookup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Thu, 23 Nov 2017 03:47:12 +0000 (11:47 +0800)]
ipvlan: Fix insufficient skb linear check for ipv6 icmp
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for ipv6 header. But it
would use the latter memory directly without linear check when it is icmp.
So it still may access the unepxected memory in ipvlan_addr_lookup.
Now invoke the pskb_may_pull again if it is ipv6 icmp.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gao Feng [Thu, 23 Nov 2017 03:47:11 +0000 (11:47 +0800)]
ipvlan: Fix insufficient skb linear check for arp
In the function ipvlan_get_L3_hdr, current codes use pskb_may_pull to
make sure the skb header has enough linear room for arp header. But it
would access the arp payload in func ipvlan_addr_lookup. So it still may
access the unepxected memory.
Now use arp_hdr_len(port->dev) instead of the arp header as the param.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 23 Nov 2017 03:27:24 +0000 (11:27 +0800)]
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
Stefano pointed that configure or show UDP_ZERO_CSUM6_RX/TX info doesn't
make sense if we haven't enabled CONFIG_IPV6. Fix it by adding
if IS_ENABLED(CONFIG_IPV6) check.
Fixes: e714b39ceae4 ("geneve: UDP checksum configuration via netlink") Fixes: 5162db683666 ("geneve: fix fill_info when link down") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Nov 2017 17:53:38 +0000 (02:53 +0900)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2017-11-21
This series contains fixes for igb/vf, ixgbe/vf, i40e/vf and fm10k.
Jake fixes a regression issue with older firmware, where we were using
the NVM lock to synchronize NVM reads for all devices and firmware
versions, yet this caused issues with older firmware prior to version
1.5. Fixed this by only grabbing the lock for newer devices and firmware
version 1.5 or newer.
Zijie Pan fixes the calculation of the i40e VF MAC addresses, where it was
possible to increment to the next MAC entry without calling
i40e_add_mac_filter().
Amritha removes the upper limit of 64 queues on a channel VSI since the
upper bound is determined by the VSI's num_queue_pairs.
Filip fixes an issue during FLR resets, where should have been checking
for upcoming core reset and if so, just return with I40E_ERR_NOT_READY.
Alan fixes the notifying clients of l2 parameters by copying the
parameters to the client instance struct and re-organizes the priority
in which the client tasks fire so that if the flag for notifying l2
params is set, it will trigger before the client open task. Also fixed
the promiscuous settings after reset for all the VSI's.
Brian King from IBM fixes an issue seen on Power systems which would
result in skb list corruption and eventual kernel oops. Brian
provides the same fix for nearly all our drivers, to replace the
read_barrier_depends with smp_rmb() to ensure loads are ordered with
respect to the load of tx_buffer->next_to_watch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 22 Nov 2017 01:37:46 +0000 (17:37 -0800)]
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.
Fixes: 4802af2d21e3 ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Tue, 21 Nov 2017 15:22:25 +0000 (10:22 -0500)]
net: accept UFO datagrams from tuntap and packet
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 81089070a3aa~1..382960fc86c8.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 7ad0d8d109a7 ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 5d41aad7f537
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
Commit cea1c9cc4dd192a3f476342a88990d7823e8507e partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de> Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 21 Nov 2017 15:08:57 +0000 (07:08 -0800)]
net: ipv6: Fixup device for anycast routes during copy
Florian reported a breakage with anycast routes due to commit 1ad23e7d336a ("net: ipv6: put host and anycast routes on device with
address"). Prior to this commit anycast routes were added against the
loopback device causing repetitive route entries with no insight into
why they existed. e.g.:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev lo proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
anycast fe80:: dev lo proto kernel metric 0 pref medium
The point of commit 1ad23e7d336a is to add the routes using the device
with the address which is causing the route to be added. e.g.,:
$ ip -6 ro ls table local type anycast
anycast 2001:db8:1:: dev eth1 proto kernel metric 0 pref medium
anycast 2001:db8:2:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth2 proto kernel metric 0 pref medium
anycast fe80:: dev eth1 proto kernel metric 0 pref medium
For traffic to work as it did before, the dst device needs to be switched
to the loopback when the copy is created similar to local routes.
Fixes: 1ad23e7d336a ("net: ipv6: put host and anycast routes on device with address") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: Fix preinitialization of buf_desc in __smc_buf_create()
With gcc-4.1.2:
net/smc/smc_core.c: In function ‘__smc_buf_create’:
net/smc/smc_core.c:567: warning: ‘bufsize’ may be used uninitialized in this function
Indeed, if the for-loop is never executed, bufsize is used
uninitialized. In addition, buf_desc is stored for later use, while it
is still a NULL pointer.
Before, error handling was done by checking if buf_desc is non-NULL.
The cleanup changed this to an error check, but forgot to update the
preinitialization of buf_desc to an error pointer.
Update the preinitializatin of buf_desc to fix this.
Fixes: 549978f108a8f286 ("net/smc: cleanup function __smc_buf_create()") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Tue, 21 Nov 2017 12:23:53 +0000 (13:23 +0100)]
net/smc: use sk_rcvbuf as start for rmb creation
Commit 2832190987bf ("net/smc: common functions for RMBs and send buffers")
merged handling of SMC receive and send buffers. It introduced sk_buf_size
as merged start value for size determination. But since sk_buf_size is not
used at all, sk_sndbuf is erroneously used as start for rmb creation.
This patch makes sure, sk_buf_size is really used as intended, and
sk_rcvbuf is used as start value for rmb creation.
Fixes: 2832190987bf ("net/smc: common functions for RMBs and send buffers") Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 21 Nov 2017 07:50:12 +0000 (09:50 +0200)]
ipv6: Do not consider linkdown nexthops during multipath
When the 'ignore_routes_with_linkdown' sysctl is set, we should not
consider linkdown nexthops during route lookup.
While the code correctly verifies that the initially selected route
('match') has a carrier, it does not perform the same check in the
subsequent multipath selection, resulting in a potential packet loss.
In case the chosen route does not have a carrier and the sysctl is set,
choose the initially selected route.
Fixes: 182161a063f5 ("net: ipv6 sysctl option to ignore routes when nexthop link is down") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: David Ahern <dsahern@gmail.com> Acked-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Kapl [Mon, 20 Nov 2017 21:21:13 +0000 (22:21 +0100)]
net: sched: fix crash when deleting secondary chains
If you flush (delete) a filter chain other than chain 0 (such as when
deleting the device), the kernel may run into a use-after-free. The
chain refcount must not be decremented unless we are sure we are done
with the chain.
To reproduce the bug, run:
ip link add dtest type dummy
tc qdisc add dev dtest ingress
tc filter add dev dtest chain 1 parent ffff: flower
ip link del dtest
Introduced in: commit 1c7b1f33070c ("net/sched: fix filter flushing"),
but unless you have KAsan or luck, you won't notice it until
commit 1cececb47428 ("cls_flower: use tcf_exts_get_net() before call_rcu()")
Fixes: 1c7b1f33070c ("net/sched: fix filter flushing") Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Roman Kapl <code@rkapl.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Thu, 23 Nov 2017 14:25:26 +0000 (23:25 +0900)]
kbuild: drop $(extra-y) from real-objs-y
$(real-objs-y) in only used in scripts/Makefile.build to form
"targets", but $(extra-y) is added to "targets" in another line.
We do not need to add $(extra-y) twice.
Masahiro Yamada [Wed, 15 Nov 2017 09:19:20 +0000 (18:19 +0900)]
kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
The "rpm" has been kept for backward compatibility since pre-git era.
I am planning to remove it after the Linux 4.18 release. Annouce the
end of the support, prompting to use "rpm-pkg" instead.
If you use "rpm", it will work like "rpm-pkg", but warning messages
will be displayed as follows:
WARNING: "rpm" target will be removed after Linux 4.18
Please use "rpm-pkg" instead.
Masahiro Yamada [Wed, 15 Nov 2017 09:17:07 +0000 (18:17 +0900)]
kbuild: pkg: use --transform option to prefix paths in tar
For rpm-pkg and deb-pkg, a source tar file is created. All paths in
the archive must be prefixed with the base name of the tar so that
everything is contained in the directory when you extract it.
Currently, scripts/package/Makefile uses a symlink for that, and
removes it after the tar is created.
If you terminate the build during the tar creation, the symlink is
left over. Then, at the next package build, you will see a warning
like follows:
ln: '.' and 'kernel-4.14.0+/.' are the same file
It is possible to fix it by adding -n (--no-dereference) option to
the "ln" command, but a cleaner way is to use --transform option
of "tar" command. This option is GNU extension, but it should not
hurt to use it in the Linux build system.
The 'S' flag is needed to exclude symlinks from the path fixup.
Without it, symlinks in the kernel are broken.
Masahiro Yamada [Tue, 14 Nov 2017 11:38:07 +0000 (20:38 +0900)]
coccinelle: fix parallel build with CHECK=scripts/coccicheck
The command "make -j8 C=1 CHECK=scripts/coccicheck" produces
lots of "coccicheck failed" error messages.
Julia Lawall explained the Coccinelle behavior as follows:
"The problem on the Coccinelle side is that it uses a subdirectory
with the name of the semantic patch to store standard output and
standard error for the different threads. I didn't want to use a
name with the pid, so that one could easily find this information
while Coccinelle is running. Normally the subdirectory is cleaned
up when Coccinelle completes, so there is only one of them at a time.
Maybe it is best to just add the pid. There is the risk that these
subdirectories will accumulate if Coccinelle crashes in a way such
that they don't get cleaned up, but Coccinelle could print a warning
if it detects this case, rather than failing."
When scripts/coccicheck is used as CHECK tool and -j option is given
to Make, the whole of build process runs in parallel. So, multiple
processes try to get access to the same subdirectory.
I notice spatch creates the subdirectory only when it runs in parallel
(i.e. --jobs <N> is given and <N> is greater than 1).
Setting NPROC=1 is a reasonable solution; spatch does not create the
subdirectory. Besides, ONLINE=1 mode takes a single file input for
each spatch invocation, so there is no reason to parallelize it in
the first place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Julia Lawall <Julia.Lawall@lip6.fr>
when the verifier detects that register contains a runtime constant
and it's compared with another constant it will prune exploration
of the branch that is guaranteed not to be taken at runtime.
This is all correct, but malicious program may be constructed
in such a way that it always has a constant comparison and
the other branch is never taken under any conditions.
In this case such path through the program will not be explored
by the verifier. It won't be taken at run-time either, but since
all instructions are JITed the malicious program may cause JITs
to complain about using reserved fields, etc.
To fix the issue we have to track the instructions explored by
the verifier and sanitize instructions that are dead at run time
with NOPs. We cannot reject such dead code, since llvm generates
it for valid C code, since it doesn't do as much data flow
analysis as the verifier does.
Fixes: 41e3263fc6b1 ("bpf: verifier (add verifier core)") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 23 Nov 2017 07:09:18 +0000 (21:09 -1000)]
Merge tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
Drivers updates:
- Use generic nvmem to expose the Non volatile ram for ds1305,
ds1511, m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume"
* tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
dt-bindings: rtc: imxdi: Improve the bindings text
rtc: sc27xx: Add Spreadtrum SC27xx PMIC RTC driver
dt-bindings: rtc: Add Spreadtrum SC27xx RTC documentation
rtc: at91rm9200: fix reading alarm value
rtc: at91rm9200: stop calculating yday in at91_rtc_readalarm
rtc: sysfs: Use time64_t variables to set time/alarm
rtc: xgene: mark PM functions as __maybe_unused
rtc: xgene: Fix suspend/resume
rtc: pcf8563: don't alway enable the alarm
rtc: pcf8563: fix output clock rate
rtc: rx8010: Fix for incorrect return value
rtc: rx8010: Specify correct address for RX8010_RESV31
rtc: rx8010: Remove duplicate define
rtc: m41t80: remove unneeded checks from m41t80_sqw_set_rate
rtc: m41t80: avoid i2c read in m41t80_sqw_is_prepared
rtc: m41t80: avoid i2c read in m41t80_sqw_recalc_rate
rtc: m41t80: fix m41t80_sqw_round_rate return value
rtc: m41t80: m41t80_sqw_set_rate should return 0 on success
rtc: add support for NXP PCF85363 real-time clock
rtc: omap: Support scratch registers
...
Will generate a lockdep warning. The issue is that the actual write
to %gs would cause an exception with IRQs disabled, and the exception
handler would, as an inadvertent side effect, update irqflag tracing
to reflect the IRQs-off status. native_load_gs_index() would then
turn IRQs back on and return with irqflag tracing still thinking that
IRQs were off. The dummy lock-and-unlock causes lockdep to notice the
error and warn.
Fix it by adding the missing tracing.
Apparently nothing did this in a context where it mattered. I haven't
tried to find a code path that would actually exhibit the warning if
appropriately nasty user code were running.
I suspect that the security impact of this bug is very, very low --
production systems don't run with lockdep enabled, and the warning is
mostly harmless anyway.
Found during a quick audit of the entry code to try to track down an
unrelated bug that Ingo found in some still-in-development code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bpetkov@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/e1aeb0e6ba8dd430ec36c8a35e63b429698b4132.1511411918.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Thu, 23 Nov 2017 06:46:06 +0000 (20:46 -1000)]
Merge tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd
Pull MTD updates from Richard Weinberger:
"General changes:
- Unconfuse get_unmapped_area and point/unpoint driver methods
- New partition parser: sharpslpart
- Kill GENERIC_IO
- Various fixes
NAND changes:
- Add a flag to mark NANDs that require 3 address cycles to encode a
page address
- Set a default ECC/free layout when NAND_ECC_NONE is requested
- Fix a bug in panic_nand_write()
- Another batch of cleanups for the denali driver
- Fix PM support in the atmel driver
- Remove support for platform data in the omap driver
- Fix subpage write in the omap driver
- Fix irq handling in the mtk driver
- Change link order of mtk_ecc and mtk_nand drivers to speed up boot
time
- Change log level of ECC error messages in the mxc driver
- Patch the pxa3xx driver to support Armada 8k platforms
- Add BAM DMA support to the qcom driver
- Convert gpio-nand to the GPIO desc API
- Fix ECC handling in the mt29f driver
SPI-NOR changes:
- Introduce system power management support
- New mechanism to select the proper .quad_enable() hook by JEDEC
ID, when needed, instead of only by manufacturer ID
- Add support to new memory parts from Gigadevice, Winbond, Macronix
and Everspin
- Maintainance for Cadence, Intel, Mediatek and STM32 drivers"
* tag 'for-linus-20171120' of git://git.infradead.org/linux-mtd: (85 commits)
mtd: Avoid probe failures when mtd->dbg.dfs_dir is invalid
mtd: sharpslpart: Add sharpslpart partition parser
mtd: Add sanity checks in mtd_write/read_oob()
mtd: remove the get_unmapped_area method
mtd: implement mtd_get_unmapped_area() using the point method
mtd: chips/map_rom.c: implement point and unpoint methods
mtd: chips/map_ram.c: implement point and unpoint methods
mtd: mtdram: properly handle the phys argument in the point method
mtd: mtdswap: fix spelling mistake: 'TRESHOLD' -> 'THRESHOLD'
mtd: slram: use memremap() instead of ioremap()
kconfig: kill off GENERIC_IO option
mtd: Fix C++ comment in include/linux/mtd/mtd.h
mtd: constify mtd_partition
mtd: plat-ram: Replace manual resource management by devm
mtd: nand: Fix writing mtdoops to nand flash.
mtd: intel-spi: Add Intel Lewisburg PCH SPI super SKU PCI ID
mtd: nand: mtk: fix infinite ECC decode IRQ issue
mtd: spi-nor: Add support for mr25h128
mtd: nand: mtk: change the compile sequence of mtk_nand.o and mtk_ecc.o
mtd: spi-nor: enable 4B opcodes for mx66l51235l
...
Linus Torvalds [Thu, 23 Nov 2017 06:42:42 +0000 (20:42 -1000)]
Merge tag 'xfs-4.15-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix a memory leak in the new in-core extent map
- Refactor the xfs_dev_t conversions for easier xfsprogs porting
* tag 'xfs-4.15-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: abstract out dev_t conversions
xfs: fix memory leak in xfs_iext_free_last_leaf
Linus Torvalds [Thu, 23 Nov 2017 06:20:02 +0000 (20:20 -1000)]
Merge branch 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mode_t whack-a-mole from Al Viro:
"For all internal uses we want umode_t, which is arch-independent;
mode_t (or __kernel_mode_t, for that matter) is wrong outside of
userland ABI.
Unfortunately, that crap keeps coming back and needs to be put down
from time to time..."
* 'work.whack-a-mole' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mode_t whack-a-mole: task_dump_owner()
Linus Torvalds [Thu, 23 Nov 2017 06:17:54 +0000 (20:17 -1000)]
Merge branch '9p-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 9p filesystemfixes from Al Viro:
"Several 9p fixes"
* '9p-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
9p: Fix missing commas in mount options
net/9p: Switch to wait_event_killable()
fs/9p: Compare qid.path in v9fs_test_inode
Rob Clark [Thu, 16 Nov 2017 14:05:57 +0000 (09:05 -0500)]
dt-bindings: remove file that was added accidentally
I think this snuck in when I applied the patch for 72cd3fbe69e1 (didn't
apply cleanly, required some manual applying + git-add). It is unused
and shouldn't be here. My bad.
Fixes: 72cd3fbe69e1 "drm/msm: Support multiple ringbuffers" Signed-off-by: Rob Clark <robdclark@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 23 Nov 2017 00:56:11 +0000 (10:56 +1000)]
Merge branch 'drm-next-4.15' of git://people.freedesktop.org/~agd5f/linux into drm-next
more misc amdgpu fixes.
* 'drm-next-4.15' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix rmmod KCQ disable failed error
drm/amdgpu: fix kernel hang when starting VNC server
drm/amdgpu: don't skip attributes when powerplay is enabled
drm/amd/pp: fix typecast error in powerplay.
Revert "drm/radeon: dont switch vt on suspend"
drm/amd/amdgpu: fix over-bound accessing in amdgpu_cs_wait_any_fence
drm/amd/powerplay: fix unfreeze level smc message for smu7
drm/amdgpu:fix memleak
drm/amdgpu:fix memleak in takedown
Dave Airlie [Wed, 22 Nov 2017 22:56:34 +0000 (08:56 +1000)]
Merge tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux into drm-next
drm/imx: various cleanups
- Switch to drm_*_get/put() helpers
- Use correct parallel-display connector enum: DPI instead of VGA
- Remove incorrect unit name from device tree binding documentation example
- Remove an unused variable
* tag 'imx-drm-next-2017-10-18' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-v3: ipu-dc: Remove unused 'di' variable
dt-bindings: fsl-imx-drm: Remove incorrect "@di0" usage
drm/imx: parallel-display: use correct connector enum
drm/imx: switch to drm_*_get(), drm_*_put() helpers
Daniel Borkmann [Wed, 22 Nov 2017 20:40:54 +0000 (21:40 +0100)]
Merge branch 'bpf-fix-null-arg-semantics'
Gianluca Borello says:
====================
This set includes some fixes in semantics and usability issues that emerged
recently, and would be good to have them in net before the next release.
In particular, ARG_CONST_SIZE_OR_ZERO semantics was recently changed in
commit a05f641ff242 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") with the goal of letting the compiler generate simpler code
that the verifier can more easily accept.
To handle this change in semantics, a few checks in some helpers were
added, like in commit 5f5e5ceca653 ("bpf: change helper bpf_probe_read arg2
type to ARG_CONST_SIZE_OR_ZERO"), and those checks are less than ideal
because once they make it into a released kernel bpf programs can start
relying on them, preventing the possibility of being removed later on.
This patch tries to fix the issue by introducing a new argument type
ARG_PTR_TO_MEM_OR_NULL that can be used for helpers that can receive a
<NULL, 0> tuple. By doing so, we can fix the semantics of the other helpers
that don't need <NULL, 0> and can just handle <!NULL, 0>, allowing the code
to get rid of those checks.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Gianluca Borello [Wed, 22 Nov 2017 18:32:56 +0000 (18:32 +0000)]
bpf: change bpf_perf_event_output arg5 type to ARG_CONST_SIZE_OR_ZERO
Commit a05f641ff242 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") relaxed the treatment of ARG_CONST_SIZE_OR_ZERO due to the way
the compiler generates optimized BPF code when checking boundaries of an
argument from C code. A typical example of this optimized code can be
generated using the bpf_perf_event_output helper when operating on variable
memory:
/* len is a generic scalar */
if (len > 0 && len <= 0x7fff)
bpf_perf_event_output(ctx, &perf_map, 0, buf, len);
110: (79) r5 = *(u64 *)(r10 -40)
111: (bf) r1 = r5
112: (07) r1 += -1
113: (25) if r1 > 0x7ffe goto pc+6
114: (bf) r1 = r6
115: (18) r2 = 0xffff94e5f166c200
117: (b7) r3 = 0
118: (bf) r4 = r7
119: (85) call bpf_perf_event_output#25
R5 min value is negative, either use unsigned or 'var &= const'
With this code, the verifier loses track of the variable.
Replacing arg5 with ARG_CONST_SIZE_OR_ZERO is thus desirable since it
avoids this quite common case which leads to usability issues, and the
compiler generates code that the verifier can more easily test:
if (len <= 0x7fff)
bpf_perf_event_output(ctx, &perf_map, 0, buf, len);
or
bpf_perf_event_output(ctx, &perf_map, 0, buf, len & 0x7fff);
No changes to the bpf_perf_event_output helper are necessary since it can
handle a case where size is 0, and an empty frame is pushed.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Gianluca Borello [Wed, 22 Nov 2017 18:32:55 +0000 (18:32 +0000)]
bpf: change bpf_probe_read_str arg2 type to ARG_CONST_SIZE_OR_ZERO
Commit a05f641ff242 ("bpf: improve verifier ARG_CONST_SIZE_OR_ZERO
semantics") relaxed the treatment of ARG_CONST_SIZE_OR_ZERO due to the way
the compiler generates optimized BPF code when checking boundaries of an
argument from C code. A typical example of this optimized code can be
generated using the bpf_probe_read_str helper when operating on variable
memory:
/* len is a generic scalar */
if (len > 0 && len <= 0x7fff)
bpf_probe_read_str(p, len, s);
251: (79) r1 = *(u64 *)(r10 -88)
252: (07) r1 += -1
253: (25) if r1 > 0x7ffe goto pc-42
254: (bf) r1 = r7
255: (79) r2 = *(u64 *)(r10 -88)
256: (bf) r8 = r4
257: (85) call bpf_probe_read_str#45
R2 min value is negative, either use unsigned or 'var &= const'
With this code, the verifier loses track of the variable.
Replacing arg2 with ARG_CONST_SIZE_OR_ZERO is thus desirable since it
avoids this quite common case which leads to usability issues, and the
compiler generates code that the verifier can more easily test:
if (len <= 0x7fff)
bpf_probe_read_str(p, len, s);
or
bpf_probe_read_str(p, len & 0x7fff, s);
No changes to the bpf_probe_read_str helper are necessary since
strncpy_from_unsafe itself immediately returns if the size passed is 0.
Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Gianluca Borello [Wed, 22 Nov 2017 18:32:54 +0000 (18:32 +0000)]
bpf: remove explicit handling of 0 for arg2 in bpf_probe_read
Commit 5f5e5ceca653 ("bpf: change helper bpf_probe_read arg2 type to
ARG_CONST_SIZE_OR_ZERO") changed arg2 type to ARG_CONST_SIZE_OR_ZERO to
simplify writing bpf programs by taking advantage of the new semantics
introduced for ARG_CONST_SIZE_OR_ZERO which allows <!NULL, 0> arguments.
In order to prevent the helper from actually passing a NULL pointer to
probe_kernel_read, which can happen when <NULL, 0> is passed to the helper,
the commit also introduced an explicit check against size == 0.
After the recent introduction of the ARG_PTR_TO_MEM_OR_NULL type,
bpf_probe_read can not receive a pair of <NULL, 0> arguments anymore, thus
the check is not needed anymore and can be removed, since probe_kernel_read
can correctly handle a <!NULL, 0> call. This also fixes the semantics of
the helper before it gets officially released and bpf programs start
relying on this check.
Fixes: 5f5e5ceca653 ("bpf: change helper bpf_probe_read arg2 type to ARG_CONST_SIZE_OR_ZERO") Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Gianluca Borello [Wed, 22 Nov 2017 18:32:53 +0000 (18:32 +0000)]
bpf: introduce ARG_PTR_TO_MEM_OR_NULL
With the current ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM semantics, an helper
argument can be NULL when the next argument type is ARG_CONST_SIZE_OR_ZERO
and the verifier can prove the value of this next argument is 0. However,
most helpers are just interested in handling <!NULL, 0>, so forcing them to
deal with <NULL, 0> makes the implementation of those helpers more
complicated for no apparent benefits, requiring them to explicitly handle
those corner cases with checks that bpf programs could start relying upon,
preventing the possibility of removing them later.
Solve this by making ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM never accept NULL
even when ARG_CONST_SIZE_OR_ZERO is set, and introduce a new argument type
ARG_PTR_TO_MEM_OR_NULL to explicitly deal with the NULL case.
Currently, the only helper that needs this is bpf_csum_diff_proto(), so
change arg1 and arg3 to this new type as well.
Also add a new battery of tests that explicitly test the
!ARG_PTR_TO_MEM_OR_NULL combination: all the current ones testing the
various <NULL, 0> variations are focused on bpf_csum_diff, so cover also
other helpers.
Signed-off-by: Gianluca Borello <g.borello@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Michael Ellerman [Wed, 22 Nov 2017 12:17:01 +0000 (23:17 +1100)]
powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
I got the logic wrong in the DT CPU features code when I added the
Power9 DD2.1 feature. We should be setting the bit if we detect a
DD2.1, not clearing it if we detect a DD2.0.
This code isn't actually exercised at the moment so nothing is
actually broken.
Fixes: 31476f4bb7c7 ("powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IMC_MAX_PMU is used for static storage (per_nest_pmu_arr) which holds
nest pmu information. Current value for the macro is 32 based on
the initial number of nest pmu units supported by the nest microcode.
But going forward, microcode could support more nest units. Instead
of static storage, patch to fix the code to dynamically allocate an
array based on the number of nest imc units found in the device tree.
Fixes:95ec3edcfc615 ('powerpc/powernv: Detect and create IMC device') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/perf: Fix pmu_count to count only nest imc pmus
"pmu_count" in opal_imc_counters_probe() is intended to hold
the number of successful nest imc pmu registerations. But
current code also counts other imc units like core_imc and
thread_imc. Patch add a check to count only nest imc pmus.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Tue, 21 Nov 2017 14:28:20 +0000 (15:28 +0100)]
powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
On powerpc32, patch_instruction() is called by apply_feature_fixups()
which is called from early_init()
There is the following note in front of early_init():
* Note that the kernel may be running at an address which is different
* from the address that it was linked at, so we must use RELOC/PTRRELOC
* to access static data (including strings). -- paulus
Therefore, slab_is_available() cannot be called yet, and
text_poke_area must be addressed with PTRRELOC()
Fixes: 841d6be2e6ec ("powerpc/mm: Implement STRICT_KERNEL_RWX on PPC32") Cc: stable@vger.kernel.org # v4.14+ Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The previous fix for addressing the breakage in vmaster slave
initialization, commit a5fa33054f75 ("ALSA: hda - Fix incorrect TLV
callback check introduced during set_fs() removal"), introduced a new
helper to process over each slave kctl. However, this helper passes
only the original kctl, not the virtual slave kctl. As a result,
HD-audio driver (which is the only user so far) couldn't initialize
the slave correctly because it's trying to update the value directly
with the original kctl, not with the mapped kctl.
This patch fixes the situation again by passing both the mapped slaved
and original slave kctls to the function. Luckily there is a single
caller as of now, so changing the call signature is no big matter.
Brian King [Fri, 17 Nov 2017 17:05:49 +0000 (11:05 -0600)]
i40evf: Use smp_rmb rather than read_barrier_depends
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brian King [Fri, 17 Nov 2017 17:05:48 +0000 (11:05 -0600)]
fm10k: Use smp_rmb rather than read_barrier_depends
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / kernel.git / log