pte_clear() et al are based on two paravirt steps today: one step to
create a page table entry with all zeroes, and one step to write this
entry value.
Juergen Gross [Sat, 15 Aug 2020 10:06:40 +0000 (12:06 +0200)]
x86/paravirt: Remove set_pte_at() pv-op
On x86 set_pte_at() is now always falling back to set_pte(). So instead
of having this fallback after the paravirt maze just drop the
set_pte_at paravirt operation and let set_pte_at() use the set_pte()
function directly.
Linus Torvalds [Fri, 14 Aug 2020 23:01:59 +0000 (16:01 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of patches which arrived too late to stabilise in
-next for the first pull.
It's really just an lpfc driver update and an assortment of minor
fixes, all in drivers. The only core update is to the zone block
device driver, which isn't the one most people use"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Update lpfc version to 12.8.0.3
scsi: lpfc: Fix LUN loss after cable pull
scsi: lpfc: Fix validation of bsg reply lengths
scsi: lpfc: Fix retry of PRLI when status indicates its unsupported
scsi: lpfc: Fix oops when unloading driver while running mds diags
scsi: lpfc: Fix RSCN timeout due to incorrect gidft counter
scsi: lpfc: Fix no message shown for lpfc_hdw_queue out of range value
scsi: lpfc: Fix FCoE speed reporting
scsi: lpfc: Add missing misc_deregister() for lpfc_init()
scsi: lpfc: nvmet: Avoid hang / use-after-free again when destroying targetport
scsi: scsi_transport_sas: Add spaces around binary operator "|"
scsi: sd_zbc: Improve zone revalidation
scsi: libfc: Free skb in fc_disc_gpn_id_resp() for valid cases
scsi: fcoe: Memory leak fix in fcoe_sysfs_fcf_del()
scsi: target: Make iscsit_register_transport() return void
Linus Torvalds [Fri, 14 Aug 2020 23:00:09 +0000 (16:00 -0700)]
Merge tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The majority of this batch is conversion of the PWM period and duty
cycle to 64-bit unsigned integers, which is required so that some
types of hardware can generate the full range of signals that they're
capable of.
The remainder is mostly minor fixes and cleanups"
* tag 'pwm/for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: handle clk_get_rate() return
pwm: Replace HTTP links with HTTPS ones
pwm: omap-dmtimer: Repair pwm_omap_dmtimer_chip's broken kerneldoc header
pwm: mediatek: Provide missing kerneldoc description for 'soc' arg
pwm: bcm-kona: Remove impossible comparison when validating duty cycle
pwm: bcm-iproc: Remove impossible comparison when validating duty cycle
pwm: iqs620a: Use lowercase hexadecimal literals for consistency
pwm: Convert period and duty cycle to u64
clk: pwm: Use 64-bit division function
backlight: pwm_bl: Use 64-bit division function
pwm: sun4i: Use nsecs_to_jiffies to avoid a division
pwm: sifive: Use 64-bit division macro
pwm: iqs620a: Use 64-bit division
pwm: imx27: Use 64-bit division macro
pwm: imx-tpm: Use 64-bit division macro
pwm: clps711x: Use 64-bit division macro
hwmon: pwm-fan: Use 64-bit division macro
drm/i915: Use 64-bit division macro
Linus Torvalds [Fri, 14 Aug 2020 22:58:57 +0000 (15:58 -0700)]
Merge tag 'sound-fix-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All device-specific small fixes and quirks mostly for usual suspects,
USB-audio and HD-audio"
* tag 'sound-fix-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: echoaudio: Fix potential Oops in snd_echo_resume()
ALSA: hda/hdmi: Use force connectivity quirk on another HP desktop
ALSA: hda/realtek - Fix unused variable warning
ALSA: hda - reverse the setting value in the micmute_led_set
ALSA: echoaduio: Drop superfluous volatile modifier
ALSA: usb-audio: Disable Lenovo P620 Rear line-in volume control
ALSA: usb-audio: add quirk for Pioneer DDJ-RB
ALSA: usb-audio: work around streaming quirk for MacroSilicon MS2109
ALSA: hda - fix the micmute led status for Lenovo ThinkCentre AIO
ALSA: usb-audio: fix overeager device match for MacroSilicon MS2109
ALSA: hda/realtek: Fix pin default on Intel NUC 8 Rugged
ALSA: usb-audio: Creative USB X-Fi Pro SB1095 volume knob support
ALSA: usb-audio: fix spelling mistake "buss" -> "bus"
Linus Torvalds [Fri, 14 Aug 2020 22:22:43 +0000 (15:22 -0700)]
dma-debug: remove debug_dma_assert_idle() function
This remoes the code from the COW path to call debug_dma_assert_idle(),
which was added many years ago.
Google shows that it hasn't caught anything in the 6+ years we've had it
apart from a false positive, and Hugh just noticed how it had a very
unfortunate spinlock serialization in the COW path.
He fixed that issue the previous commit (70565a581500: "dma-debug: fix
debug_dma_assert_idle(), use rcu_read_lock()"), but let's see if anybody
even notices when we remove this function entirely.
NOTE! We keep the dma tracking infrastructure that was added by the
commit that introduced it. Partly to make it easier to resurrect this
debug code if we ever deside to, and partly because that tracking by pfn
and offset looks quite reasonable.
The problem with this debug code was simply that it was expensive and
didn't seem worth it, not that it was wrong per se.
Acked-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 13 Aug 2020 03:17:00 +0000 (20:17 -0700)]
dma-debug: fix debug_dma_assert_idle(), use rcu_read_lock()
Since commit 884252dea5ea ("mm: rewrite wait_on_page_bit_common()
logic") improved unlock_page(), it has become more noticeable how
cow_user_page() in a kernel with CONFIG_DMA_API_DEBUG=y can create and
suffer from heavy contention on DMA debug's radix_lock in
debug_dma_assert_idle().
It is only doing a lookup: use rcu_read_lock() and rcu_read_unlock()
instead; though that does require the static ents[] to be moved
onstack...
...but, hold on, isn't that radix_tree_gang_lookup() and loop doing
quite the wrong thing: searching CACHELINES_PER_PAGE entries for an
exact match with the first cacheline of the page in question?
radix_tree_gang_lookup() is the right tool for the job, but we need
nothing more than to check the first entry it can find, reporting if
that falls anywhere within the page.
(Is RCU safe here? As safe as using the spinlock was. The entries are
never freed, so don't need to be freed by RCU. They may be reused, and
there is a faint chance of a race, with an offending entry reused while
printing its error info; but the spinlock did not prevent that either,
and I agree that it's not worth worrying about. ]
[ Side noe: this patch is a clear improvement to the status quo, but the
next patch will be removing this debug function entirely.
But just in case we decide we want to resurrect the debugging code
some day, I'm first applying this improvement patch so that it doesn't
get lost - Linus ]
Fixes: faa12eb3f3c1 ("dma debug: account for cachelines and read-only mappings in overlap tracking") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 14 Aug 2020 21:26:08 +0000 (14:26 -0700)]
Merge tag 'timers-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping updates from Thomas Gleixner:
"A set of timekeeping/VDSO updates:
- Preparatory work to allow S390 to switch over to the generic VDSO
implementation.
S390 requires that the VDSO data pointer is handed in to the
counter read function when time namespace support is enabled.
Adding the pointer is a NOOP for all other architectures because
the compiler is supposed to optimize that out when it is unused in
the architecture specific inline. The change also solved a similar
problem for MIPS which fortunately has time namespaces not yet
enabled.
S390 needs to update clock related VDSO data independent of the
timekeeping updates. This was solved so far with yet another
sequence counter in the S390 implementation. A better solution is
to utilize the already existing VDSO sequence count for this. The
core code now exposes helper functions which allow to serialize
against the timekeeper code and against concurrent readers.
S390 needs extra data for their clock readout function. The initial
common VDSO data structure did not provide a way to add that. It
now has an embedded architecture specific struct embedded which
defaults to an empty struct.
Doing this now avoids tree dependencies and conflicts post rc1 and
allows all other architectures which work on generic VDSO support
to work from a common upstream base.
- A trivial comment fix"
* tag 'timers-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Delete repeated words in comments
lib/vdso: Allow to add architecture-specific vdso data
timekeeping/vsyscall: Provide vdso_update_begin/end()
vdso/treewide: Add vdso_data pointer argument to __arch_get_hw_counter()
Linus Torvalds [Fri, 14 Aug 2020 21:17:51 +0000 (14:17 -0700)]
Merge tag 'timers-core-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more timer updates from Thomas Gleixner:
"A set of posix CPU timer changes which allows to defer the heavy work
of posix CPU timers into task work context. The tick interrupt is
reduced to a quick check which queues the work which is doing the
heavy lifting before returning to user space or going back to guest
mode. Moving this out is deferring the signal delivery slightly but
posix CPU timers are inaccurate by nature as they depend on the tick
so there is no real damage. The relevant test cases all passed.
This lifts the last offender for RT out of the hard interrupt context
tick handler, but it also has the general benefit that the actual
heavy work is accounted to the task/process and not to the tick
interrupt itself.
Further optimizations are possible to break long sighand lock hold and
interrupt disabled (on !RT kernels) times when a massive amount of
posix CPU timers (which are unpriviledged) is armed for a
task/process.
This is currently only enabled for x86 because the architecture has to
ensure that task work is handled in KVM before entering a guest, which
was just established for x86 with the new common entry/exit code which
got merged post 5.8 and is not the case for other KVM architectures"
* tag 'timers-core-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Select POSIX_CPU_TIMERS_TASK_WORK
posix-cpu-timers: Provide mechanisms to defer timer handling to task_work
posix-cpu-timers: Split run_posix_cpu_timers()
Linus Torvalds [Fri, 14 Aug 2020 21:14:28 +0000 (14:14 -0700)]
Merge tag 'irq-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"Two fixes in the core interrupt code which ensure that all error exits
unlock the descriptor lock"
* tag 'irq-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Unlock irq descriptor after errors
genirq/PM: Always unlock IRQ descriptor in rearm_wake_irq()
Linus Torvalds [Fri, 14 Aug 2020 21:04:53 +0000 (14:04 -0700)]
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"A few patches all over the place during this cycle, mostly bug and
sparse warning fixes for OpenRISC, but a few enhancements too. Note,
there are 2 non OpenRISC specific fixups.
Non OpenRISC fixes:
- In init we need to align the init_task correctly to fix an issue
with MUTEX_FLAGS, reviewed by Peter Z. No one picked this up so I
kept it on my tree.
- In asm-generic/io.h I fixed up some sparse warnings, OK'd by Arnd.
Arnd asked to merge it via my tree.
OpenRISC fixes:
- Many fixes for OpenRISC sprase warnings.
- Add support OpenRISC SMP tlb flushing rather than always flushing
the entire TLB on every CPU.
- Fix bug when dumping stack via /proc/xxx/stack of user threads"
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: uaccess: Add user address space check to access_ok
openrisc: signal: Fix sparse address space warnings
openrisc: uaccess: Remove unused macro __addr_ok
openrisc: uaccess: Use static inline function in access_ok
openrisc: uaccess: Fix sparse address space warnings
openrisc: io: Fixup defines and move include to the end
asm-generic/io.h: Fix sparse warnings on big-endian architectures
openrisc: Implement proper SMP tlb flushing
openrisc: Fix oops caused when dumping stack
openrisc: Add support for external initrd images
init: Align init_task to avoid conflict with MUTEX_FLAGS
openrisc: fix __user in raw_copy_to_user()'s prototype
Linus Torvalds [Fri, 14 Aug 2020 20:40:27 +0000 (13:40 -0700)]
Merge tag 'powerpc-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"One fix for a boot crash on some platforms introduced by the recent
pkey refactoring.
Thanks to Christian Zigotzky and Aneesh Kumar K.V"
* tag 'powerpc-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pkeys: Fix boot failures with Nemo board (A-EON AmigaOne X1000)
Linus Torvalds [Fri, 14 Aug 2020 20:34:37 +0000 (13:34 -0700)]
Merge tag 'for-linus-5.9-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- Remove support for running as 32-bit Xen PV-guest.
32-bit PV guests are rarely used, are lacking security fixes for
Meltdown, and can be easily replaced by PVH mode. Another series for
doing more cleanup will follow soon (removal of 32-bit-only pvops
functionality).
- Fixes and additional features for the Xen display frontend driver.
* tag 'for-linus-5.9-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drm/xen-front: Pass dumb buffer data offset to the backend
xen: Sync up with the canonical protocol definition in Xen
drm/xen-front: Add YUYV to supported formats
drm/xen-front: Fix misused IS_ERR_OR_NULL checks
xen/gntdev: Fix dmabuf import with non-zero sgt offset
x86/xen: drop tests for highmem in pv code
x86/xen: eliminate xen-asm_64.S
x86/xen: remove 32-bit Xen PV guest support
Linus Torvalds [Fri, 14 Aug 2020 20:31:25 +0000 (13:31 -0700)]
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v fixes from Wei Liu:
- fix oops reporting on Hyper-V
- make objtool happy
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Make hv_setup_sched_clock inline
Drivers: hv: vmbus: Only notify Hyper-V for die events that are oops
This can happen if ptrace() or sigreturn() pokes an LDT selector into FS
or GS for a task with no LDT and something tries to read the base before
a return to usermode notices the bad selector and fixes it.
The fix is to make sure ldt pointer is not NULL.
Fixes: 66cee9012dd8 ("x86/fsgsbase/64: Fix ptrace() to read the FS/GS base accurately") Co-developed-by: Jann Horn <jannh@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Chang S. Bae <chang.seok.bae@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Markus T Metzger <markus.t.metzger@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Shankar <ravi.v.shankar@intel.com> Cc: Rik van Riel <riel@surriel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 14 Aug 2020 18:07:02 +0000 (11:07 -0700)]
Merge tag 'modules-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"The most important change would be Christoph Hellwig's patch
implementing proprietary taint inheritance, in an effort to discourage
the creation of GPL "shim" modules that interface between GPL symbols
and proprietary symbols.
Summary:
- Have modules that use symbols from proprietary modules inherit the
TAINT_PROPRIETARY_MODULE taint, in an effort to prevent GPL shim
modules that are used to circumvent _GPL exports. These are modules
that claim to be GPL licensed while also using symbols from
proprietary modules. Such modules will be rejected while non-GPL
modules will inherit the proprietary taint.
- Module export space cleanup. Unexport symbols that are unused
outside of module.c or otherwise used in only built-in code"
* tag 'modules-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
modules: inherit TAINT_PROPRIETARY_MODULE
modules: return licensing information from find_symbol
modules: rename the licence field in struct symsearch to license
modules: unexport __module_address
modules: unexport __module_text_address
modules: mark each_symbol_section static
modules: mark find_symbol static
modules: mark ref_module static
modules: linux/moduleparam.h: drop duplicated word in a comment
Linus Torvalds [Fri, 14 Aug 2020 18:04:45 +0000 (11:04 -0700)]
Merge tag 'kconfig-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- remove '---help---' keyword support
- fix mouse events for 'menuconfig' symbols in search view of qconf
- code cleanups of qconf
* tag 'kconfig-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
kconfig: qconf: move setOptionMode() to ConfigList from ConfigView
kconfig: qconf: do not limit the pop-up menu to the first row
kconfig: qconf: refactor icon setups
kconfig: qconf: remove unused voidPix, menuInvPix
kconfig: qconf: remove ConfigItem::text/setText
kconfig: qconf: remove ConfigList::addColumn/removeColumn
kconfig: qconf: remove ConfigItem::pixmap/setPixmap
kconfig: qconf: drop more localization code
kconfig: qconf: remove 'parent' from ConfigList::updateMenuList()
kconfig: qconf: remove unused argument from ConfigView::updateList()
kconfig: qconf: remove unused argument from ConfigList::updateList()
kconfig: qconf: omit parent to QHBoxLayout()
kconfig: qconf: remove name from ConfigSearchWindow constructor
kconfig: qconf: remove unused ConfigList::listView()
kconfig: qconf: overload addToolBar() to create and insert toolbar
kconfig: qconf: remove toolBar from ConfigMainWindow members
kconfig: qconf: use 'menu' variable for (QMenu *)
kconfig: qconf: do not use 'menu' variable for (QMenuBar *)
kconfig: qconf: remove ->addSeparator() to menuBar
kconfig: add 'static' to some file-local data
...
Masahiro Yamada [Fri, 7 Aug 2020 09:19:08 +0000 (18:19 +0900)]
kconfig: qconf: do not limit the pop-up menu to the first row
If you right-click the first row in the option tree, the pop-up menu
shows up, but if you right-click the second row or below, the event
is ignored due to the following check:
if (e->y() <= header()->geometry().bottom()) {
Perhaps, the intention was to show the pop-menu only when the tree
header was right-clicked, but this handler is not called in that case.
Since the origin of e->y() starts from the bottom of the header,
this check is odd.
Going forward, you can right-click anywhere in the tree to get the
pop-up menu.
Masahiro Yamada [Fri, 7 Aug 2020 09:19:07 +0000 (18:19 +0900)]
kconfig: qconf: refactor icon setups
These icon data are used by ConfigItem, but stored in each instance
of ConfigView. There is no point to keep the same data in each of 3
instances, "menu", "config", and "search".
Move the icon data to the more relevant ConfigItem class, and make
them static members.
Masahiro Yamada [Fri, 7 Aug 2020 09:18:55 +0000 (18:18 +0900)]
kconfig: qconf: overload addToolBar() to create and insert toolbar
Use the overloaded function, addToolBar(const QString &title)
to create a QToolBar object, setting its window title, and inserts
it into the toolbar area.
Linus Torvalds [Fri, 14 Aug 2020 01:41:00 +0000 (18:41 -0700)]
Merge branch 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- bus recovery can now be given a pinctrl handle and the I2C core will
do all the steps to switch to/from GPIO which can save quite some
boilerplate code from drivers
- "fallthrough" conversion
- driver updates, mostly ID additions
* 'i2c/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (32 commits)
i2c: iproc: fix race between client unreg and isr
i2c: eg20t: use generic power management
i2c: eg20t: Drop PCI wakeup calls from .suspend/.resume
i2c: mediatek: Fix i2c_spec_values description
i2c: mediatek: Add i2c compatible for MediaTek MT8192
dt-bindings: i2c: update bindings for MT8192 SoC
i2c: mediatek: Add access to more than 8GB dram in i2c driver
i2c: mediatek: Add apdma sync in i2c driver
i2c: i801: Add support for Intel Tiger Lake PCH-H
i2c: i801: Add support for Intel Emmitsburg PCH
i2c: bcm2835: Replace HTTP links with HTTPS ones
Documentation: i2c: dev: 'block process call' is supported
i2c: at91: Move to generic GPIO bus recovery
i2c: core: treat EPROBE_DEFER when acquiring SCL/SDA GPIOs
i2c: core: add generic I2C GPIO recovery
dt-bindings: i2c: add generic properties for GPIO bus recovery
i2c: rcar: avoid race when unregistering slave
i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c
i2c: tegra: Fix runtime resume to re-init VI I2C
i2c: tegra: Fix the error path in tegra_i2c_runtime_resume
...
Tonghao Zhang [Wed, 12 Aug 2020 09:56:39 +0000 (17:56 +0800)]
net: openvswitch: introduce common code for flushing flows
To avoid some issues, for example RCU usage warning and double free,
we should flush the flows under ovs_lock. This patch refactors
table_instance_destroy and introduces table_instance_flow_flush
which can be invoked by __dp_destroy or ovs_flow_tbl_flush.
Fixes: 67df6806f2fb ("net: openvswitch: fix possible memleak on destroy flow-table") Reported-by: Johan Knöös <jknoos@google.com>
Reported-at: https://mail.openvswitch.org/pipermail/ovs-discuss/2020-August/050489.html Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Ogness [Thu, 13 Aug 2020 19:39:25 +0000 (21:45 +0206)]
af_packet: TPACKET_V3: fix fill status rwlock imbalance
After @blk_fill_in_prog_lock is acquired there is an early out vnet
situation that can occur. In that case, the rwlock needs to be
released.
Also, since @blk_fill_in_prog_lock is only acquired when @tp_version
is exactly TPACKET_V3, only release it on that exact condition as
well.
And finally, add sparse annotation so that it is clearer that
prb_fill_curr_block() and prb_clear_blk_fill_status() are acquiring
and releasing @blk_fill_in_prog_lock, respectively. sparse is still
unable to understand the balance, but the warnings are now on a
higher level that make more sense.
Fixes: 39d698d2d507 ("af_packet: TPACKET_V3: replace busy-wait loop") Signed-off-by: John Ogness <john.ogness@linutronix.de> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 13 Aug 2020 17:06:43 +0000 (10:06 -0700)]
random32: add a tracepoint for prandom_u32()
There has been some heat around prandom_u32() lately, and some people
were wondering if there was a simple way to determine how often
it was used, before considering making it maybe 10 times more expensive.
This tracepoint exports the generated pseudo random value.
Tested:
perf list | grep prandom_u32
random:prandom_u32 [Tracepoint event]
perf record -a [-g] [-C1] -e random:prandom_u32 sleep 1
[ perf record: Woken up 0 times to write data ]
[ perf record: Captured and wrote 259.748 MB perf.data (924087 samples) ]
Linus Torvalds [Thu, 13 Aug 2020 20:57:45 +0000 (13:57 -0700)]
Merge tag 'docs-5.9-2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of obvious fixes that wandered in during the merge window"
* tag 'docs-5.9-2' of git://git.lwn.net/linux:
Documentation/locking/locktypes: fix the typo
doc/zh_CN: resolve undefined label warning in admin-guide index
doc/zh_CN: fix title heading markup in admin-guide cpu-load
docs: remove the 2.6 "Upgrading I2C Drivers" guide
docs: Correct the release date of 5.2 stable
mailmap: Update comments for with format and more detalis
docs: cdrom: Fix a typo and rst markup
Doc: admin-guide: use correct legends in kernel-parameters.txt
Documentation/features: refresh RISC-V arch support files
documentation: coccinelle: Improve command example for make C={1,2}
Core-api: Documentation: Replace deprecated :c:func: Usage
Dev-tools: Documentation: Replace deprecated :c:func: Usage
Filesystems: Documentation: Replace deprecated :c:func: Usage
docs: trace: fix a typo
Linus Torvalds [Thu, 13 Aug 2020 19:38:32 +0000 (12:38 -0700)]
Merge tag 's390-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- Allow s390 debug feature to handle finally more than 256 CPU numbers,
instead of truncating the most significant bits.
- Improve THP splitting required by qemu processes by making use of
walk_page_vma() instead of calling follow_page() for every single
page within each vma.
- Add missing ZCRYPT dependency to VFIO_AP to fix potential compile
problems.
- Remove not required select CLOCKSOURCE_VALIDATE_LAST_CYCLE again.
- Set node distance to LOCAL_DISTANCE instead of 0, since e.g. libnuma
translates a node distance of 0 to "no NUMA support available".
- Couple of other minor fixes and improvements.
* tag 's390-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/numa: move code to arch/s390/kernel
s390/time: remove select CLOCKSOURCE_VALIDATE_LAST_CYCLE again
s390/debug: debug feature version 3
s390/Kconfig: add missing ZCRYPT dependency to VFIO_AP
s390/numa: set node distance to LOCAL_DISTANCE
s390/pkey: remove redundant variable initialization
s390/test_unwind: fix possible memleak in test_unwind()
s390/gmap: improve THP splitting
s390/atomic: circumvent gcc 10 build regression
Linus Torvalds [Thu, 13 Aug 2020 19:26:18 +0000 (12:26 -0700)]
Merge tag 'for-5.9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"One minor update, the rest are fixes that have arrived a bit late for
the first batch. There are also some recent fixes for bugs that were
discovered during the merge window and pop up during testing.
User visible change:
- show correct subvolume path in /proc/mounts for bind mounts
Fixes:
- fix compression messages when remounting with different level or
compression algorithm
- tree-log: fix some memory leaks on error handling paths
- restore I_VERSION on remount
- fix return values and error code mixups
- fix umount crash with quotas enabled when removing sysfs files
- fix trim range on a shrunk device"
* tag 'for-5.9-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: trim: fix underflow in trim length to prevent access beyond device boundary
btrfs: fix return value mixup in btrfs_get_extent
btrfs: sysfs: fix NULL pointer dereference at btrfs_sysfs_del_qgroups()
btrfs: check correct variable after allocation in btrfs_backref_iter_alloc
btrfs: make sure SB_I_VERSION doesn't get unset by remount
btrfs: fix memory leaks after failure to lookup checksums during inode logging
btrfs: don't show full path of bind mounts in subvol=
btrfs: fix messages after changing compression level by remount
btrfs: only search for left_info if there is no right_info in try_merge_free_space
btrfs: inode: fix NULL pointer dereference if inode doesn't need compression
Linus Torvalds [Thu, 13 Aug 2020 19:22:19 +0000 (12:22 -0700)]
Merge tag 'xfs-5.9-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Two small fixes that have come in during the past week:
- Fix duplicated words in comments
- Fix an ubsan complaint about null pointer arithmetic"
* tag 'xfs-5.9-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Fix UBSAN null-ptr-deref in xfs_sysfs_init
xfs: delete duplicated words + other fixes
Linus Torvalds [Thu, 13 Aug 2020 19:18:07 +0000 (12:18 -0700)]
Merge tag 'exfat-for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat
Pull exfat updates from Namjae Jeon:
- don't clear MediaFailure and VolumeDirty bit in volume flags if these
were already set before mounting
- write multiple dirty buffers at once in sync mode
- remove unneeded EXFAT_SB_DIRTY bit set
* tag 'exfat-for-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: retain 'VolumeFlags' properly
exfat: optimize exfat_zeroed_cluster()
exfat: add error check when updating dir-entries
exfat: write multiple sectors at once
exfat: remove EXFAT_SB_DIRTY flag
Johannes Weiner [Thu, 13 Aug 2020 14:40:54 +0000 (10:40 -0400)]
mm: memcontrol: fix warning when allocating the root cgroup
Commit 9209067f96cf ("mm: memcg: charge memcg percpu memory to the
parent cgroup") adds memory tracking to the memcg kernel structures
themselves to make cgroups liable for the memory they are consuming
through the allocation of child groups (which can be significant).
This code is a bit awkward as it's spread out through several functions:
The outermost function does memalloc_use_memcg(parent) to set up
current->active_memcg, which designates which cgroup to charge, and the
inner functions pass GFP_ACCOUNT to request charging for specific
allocations. To make sure this dependency is satisfied at all times -
to make sure we don't randomly charge whoever is calling the functions -
the inner functions warn on !current->active_memcg.
However, this triggers a false warning when the root memcg itself is
allocated. No parent exists in this case, and so current->active_memcg
is rightfully NULL. It's a false positive, not indicative of a bug.
Delete the warnings for now, we can revisit this later.
Fixes: 9209067f96cf ("mm: memcg: charge memcg percpu memory to the parent cgroup") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Roman Gushchin <guro@fb.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm/xen-front: Pass dumb buffer data offset to the backend
While importing a dmabuf it is possible that the data of the buffer
is put with offset which is indicated by the SGT offset.
Respect the offset value and forward it to the backend.
xen: Sync up with the canonical protocol definition in Xen
This is the sync up with the canonical definition of the
display protocol in Xen.
1. Add protocol version as an integer
Version string, which is in fact an integer, is hard to handle in the
code that supports different protocol versions. To simplify that
also add the version as an integer.
2. Pass buffer offset with XENDISPL_OP_DBUF_CREATE
There are cases when display data buffer is created with non-zero
offset to the data start. Handle such cases and provide that offset
while creating a display buffer.
3. Add XENDISPL_OP_GET_EDID command
Add an optional request for reading Extended Display Identification
Data (EDID) structure which allows better configuration of the
display connectors over the configuration set in XenStore.
With this change connectors may have multiple resolutions defined
with respect to detailed timing definitions and additional properties
normally provided by displays.
If this request is not supported by the backend then visible area
is defined by the relevant XenStore's "resolution" property.
If backend provides extended display identification data (EDID) with
XENDISPL_OP_GET_EDID request then EDID values must take precedence
over the resolutions defined in XenStore.
xen/gntdev: Fix dmabuf import with non-zero sgt offset
It is possible that the scatter-gather table during dmabuf import has
non-zero offset of the data, but user-space doesn't expect that.
Fix this by failing the import, so user-space doesn't access wrong data.
Guenter Roeck [Tue, 11 Aug 2020 18:00:12 +0000 (11:00 -0700)]
genirq: Unlock irq descriptor after errors
In irq_set_irqchip_state(), the irq descriptor is not unlocked after an
error is encountered. While that should never happen in practice, a buggy
driver may trigger it. This would result in a lockup, so fix it.
Fixes: 9189bdaf2a72 ("genirq: Check irq_data_get_irq_chip() return value before use") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200811180012.80269-1-linux@roeck-us.net
Ondrej Mosnacek [Wed, 12 Aug 2020 12:58:25 +0000 (14:58 +0200)]
crypto: algif_aead - fix uninitialized ctx->init
In skcipher_accept_parent_nokey() the whole af_alg_ctx structure is
cleared by memset() after allocation, so add such memset() also to
aead_accept_parent_nokey() so that the new "init" field is also
initialized to zero. Without that the initial ctx->init checks might
randomly return true and cause errors.
While there, also remove the redundant zero assignments in both
functions.
Found via libkcapi testsuite.
Cc: Stephan Mueller <smueller@chronox.de> Fixes: b7dad8488f83 ("crypto: algif_aead - Only wake up when ctx->more is zero") Suggested-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Linus Torvalds [Thu, 13 Aug 2020 00:17:00 +0000 (17:17 -0700)]
Merge tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle - mostly non urgent driver fixes:
- ds1374: use watchdog core
- pcf2127: add alarm and pcf2129 support"
* tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: pcf2127: fix alarm handling
rtc: pcf2127: add alarm support
rtc: pcf2127: add pca2129 device id
rtc: max77686: Fix wake-ups for max77620
rtc: ds1307: provide an indication that the watchdog has fired
rtc: ds1374: remove unused define
rtc: ds1374: fix RTC_DRV_DS1374_WDT dependencies
rtc: cleanup obsolete comment about struct rtc_class_ops
rtc: pl031: fix set_alarm by adding back call to alarm_irq_enable
rtc: ds1374: wdt: Use watchdog core for watchdog part
rtc: Replace HTTP links with HTTPS ones
rtc: goldfish: Enable interrupt in set_alarm() when necessary
rtc: max77686: Do not allow interrupt to fire before system resume
rtc: imxdi: fix trivial typos
rtc: cpcap: fix range
====================
net: stmmac: Fix multicast filter on IPQ806x
This pair of patches are the result of discovering a failure to
correctly receive IPv6 multicast packets on such a device (in particular
DHCPv6 requests and RA solicitations). Putting the device into
promiscuous mode, or allmulti, both resulted in such packets correctly
being received. Examination of the vendor driver (nss-gmac from the
qsdk) shows that it does not enable the multicast filter and instead
falls back to allmulti.
Extend the base dwmac1000 driver to fall back when there's no suitable
hardware filter, and update the ipq806x platform to request this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPQ806x does not appear to have a functional multicast ethernet
address filter. This was observed as a failure to correctly receive IPv6
packets on a LAN to the all stations address. Checking the vendor driver
shows that it does not attempt to enable the multicast filter and
instead falls back to receiving all multicast packets, internally
setting ALLMULTI.
Use the new fallback support in the dwmac1000 driver to correctly
achieve the same with the mainline IPQ806x driver. Confirmed to fix IPv6
functionality on an RB3011 router.
Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: dwmac1000: provide multicast filter fallback
If we don't have a hardware multicast filter available then instead of
silently failing to listen for the requested ethernet broadcast
addresses fall back to receiving all multicast packets, in a similar
fashion to other drivers with no multicast filter.
Cc: stable@vger.kernel.org Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: David S. Miller <davem@davemloft.net>
Dhananjay Phadke [Tue, 11 Aug 2020 00:42:40 +0000 (17:42 -0700)]
i2c: iproc: fix race between client unreg and isr
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slave to NULL.
(1) disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6) enable_irq()
(7) Set client pointer to NULL
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318
Johannes Berg [Wed, 12 Aug 2020 19:08:53 +0000 (21:08 +0200)]
ipv4: tunnel: fix compilation on ARCH=um
With certain configurations, a 64-bit ARCH=um errors
out here with an unknown csum_ipv6_magic() function.
Include the right header file to always have it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vsock: fix potential null pointer dereference in vsock_poll()
syzbot reported this issue where in the vsock_poll() we find the
socket state at TCP_ESTABLISHED, but 'transport' is null:
general protection fault, probably for non-canonical address 0xdffffc0000000012: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
CPU: 0 PID: 8227 Comm: syz-executor.2 Not tainted 5.8.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:vsock_poll+0x75a/0x8e0 net/vmw_vsock/af_vsock.c:1038
Call Trace:
sock_poll+0x159/0x460 net/socket.c:1266
vfs_poll include/linux/poll.h:90 [inline]
do_pollfd fs/select.c:869 [inline]
do_poll fs/select.c:917 [inline]
do_sys_poll+0x607/0xd40 fs/select.c:1011
__do_sys_poll fs/select.c:1069 [inline]
__se_sys_poll fs/select.c:1057 [inline]
__x64_sys_poll+0x18c/0x440 fs/select.c:1057
do_syscall_64+0x60/0xe0 arch/x86/entry/common.c:384
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This issue can happen if the TCP_ESTABLISHED state is set after we read
the vsk->transport in the vsock_poll().
We could put barriers to synchronize, but this can only happen during
connection setup, so we can simply check that 'transport' is valid.
Fixes: 377128ab2681 ("vsock: add multi-transports support") Reported-and-tested-by: syzbot+a61bac2fcc1a7c6623fe@syzkaller.appspotmail.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 12 Aug 2020 09:32:49 +0000 (10:32 +0100)]
sfc: fix ef100 design-param checking
The handling of the RXQ/TXQ size granularity design-params had two
problems: it had a 64-bit divide that didn't build on 32-bit platforms,
and it could divide by zero if the NIC supplied 0 as the value of the
design-param. Fix both by checking for 0 and for a granularity bigger
than our min-size; if the granularity <= EFX_MIN_DMAQ_SIZE then it fits
in 32 bits, so we can cast it to u32 for the divide.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 12 Aug 2020 19:51:31 +0000 (12:51 -0700)]
Merge tag 'ceph-for-5.9-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"Xiubo has completed his work on filesystem client metrics, they are
sent to all available MDSes once per second now.
Other than that, we have a lot of fixes and cleanups all around the
filesystem, including a tweak to cut down on MDS request resends in
multi-MDS setups from Yanhu and fixups for SELinux symlink labeling
and MClientSession message decoding from Jeff"
* tag 'ceph-for-5.9-rc1' of git://github.com/ceph/ceph-client: (22 commits)
ceph: handle zero-length feature mask in session messages
ceph: use frag's MDS in either mode
ceph: move sb->wb_pagevec_pool to be a global mempool
ceph: set sec_context xattr on symlink creation
ceph: remove redundant initialization of variable mds
ceph: fix use-after-free for fsc->mdsc
ceph: remove unused variables in ceph_mdsmap_decode()
ceph: delete repeated words in fs/ceph/
ceph: send client provided metric flags in client metadata
ceph: periodically send perf metrics to MDSes
ceph: check the sesion state and return false in case it is closed
libceph: replace HTTP links with HTTPS ones
ceph: remove unnecessary cast in kfree()
libceph: just have osd_req_op_init() return a pointer
ceph: do not access the kiocb after aio requests
ceph: clean up and optimize ceph_check_delayed_caps()
ceph: fix potential mdsc use-after-free crash
ceph: switch to WARN_ON_ONCE in encode_supported_features()
ceph: add global total_caps to count the mdsc's total caps number
ceph: add check_session_state() helper and make it global
...
Linus Torvalds [Wed, 12 Aug 2020 19:41:15 +0000 (12:41 -0700)]
Merge branch 'parisc-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc updates from Helge Deller:
- Oscar Carter contributed a patch which fixes parisc's usage of
dereference_function_descriptor() and thus will allow using the
-Wcast-function-type compiler option in the top-level Makefile
- Sven Schnelle fixed a bug in the SBA code to prevent crashes during
kexec
- John David Anglin provided implementations for __smp_store_release()
and __smp_load_acquire barriers() which avoids using the sync
assembler instruction and thus speeds up barrier paths
- Some whitespace cleanups in parisc's atomic.h header file
* 'parisc-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Implement __smp_store_release and __smp_load_acquire barriers
parisc: mask out enable and reserved bits from sba imask
parisc: Whitespace cleanups in atomic.h
parisc/kernel/ftrace: Remove function callback casts
sections.h: dereference_function_descriptor() returns void pointer
Linus Torvalds [Wed, 12 Aug 2020 19:25:06 +0000 (12:25 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"PPC:
- Improvements and bugfixes for secure VM support, giving reduced
startup time and memory hotplug support.
- Locking fixes in nested KVM code
- Increase number of guests supported by HV KVM to 4094
- Preliminary POWER10 support
ARM:
- Split the VHE and nVHE hypervisor code bases, build the EL2 code
separately, allowing for the VHE code to now be built with
instrumentation
- Level-based TLB invalidation support
- Restructure of the vcpu register storage to accomodate the NV code
- Pointer Authentication available for guests on nVHE hosts
- Simplification of the system register table parsing
- MMU cleanups and fixes
- A number of post-32bit cleanups and other fixes
MIPS:
- compilation fixes
x86:
- bugfixes
- support for the SERIALIZE instruction"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (70 commits)
KVM: MIPS/VZ: Fix build error caused by 'kvm_run' cleanup
x86/kvm/hyper-v: Synic default SCONTROL MSR needs to be enabled
MIPS: KVM: Convert a fallthrough comment to fallthrough
MIPS: VZ: Only include loongson_regs.h for CPU_LOONGSON64
x86: Expose SERIALIZE for supported cpuid
KVM: x86: Don't attempt to load PDPTRs when 64-bit mode is enabled
KVM: arm64: Move S1PTW S2 fault logic out of io_mem_abort()
KVM: arm64: Don't skip cache maintenance for read-only memslots
KVM: arm64: Handle data and instruction external aborts the same way
KVM: arm64: Rename kvm_vcpu_dabt_isextabt()
KVM: arm: Add trace name for ARM_NISV
KVM: arm64: Ensure that all nVHE hyp code is in .hyp.text
KVM: arm64: Substitute RANDOMIZE_BASE for HARDEN_EL2_VECTORS
KVM: arm64: Make nVHE ASLR conditional on RANDOMIZE_BASE
KVM: PPC: Book3S HV: Rework secure mem slot dropping
KVM: PPC: Book3S HV: Move kvmppc_svm_page_out up
KVM: PPC: Book3S HV: Migrate hot plugged memory
KVM: PPC: Book3S HV: In H_SVM_INIT_DONE, migrate remaining normal-GFNs to secure-GFNs
KVM: PPC: Book3S HV: Track the state GFNs associated with secure VMs
KVM: PPC: Book3S HV: Disable page merging in H_SVM_INIT_START
...
Linus Torvalds [Wed, 12 Aug 2020 19:19:49 +0000 (12:19 -0700)]
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"Here's some more updates that missed the last pull request because I
happened to tag the tree at an earlier point in the history of
clk-next. I must have fat fingered it and checked out an older version
of clk-next on this second computer I'm using.
This time it actually includes more code for Qualcomm SoCs, the AT91
major updates, and some Rockchip SoC clk driver updates as well. I've
corrected this flow so this shouldn't happen again"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (83 commits)
clk: bcm2835: Do not use prediv with bcm2711's PLLs
clk: drop unused function __clk_get_flags
clk: hsdk: Fix bad dependency on IOMEM
dt-bindings: clock: Fix YAML schemas for LPASS clocks on SC7180
clk: mmp: avoid missing prototype warning
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
clk: qoriq: add LS1021A core pll mux options
clk: clk-atlas6: fix return value check in atlas6_clk_init()
clk: tegra: pll: Improve PLLM enable-state detection
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
clk: qcom: gcc-sdm660: Fix up gcc_mss_mnoc_bimc_axi_clk
clk: qcom: gcc-sdm660: Add missing modem reset
...
Linus Torvalds [Wed, 12 Aug 2020 19:13:44 +0000 (12:13 -0700)]
Merge tag 'linux-watchdog-5.9-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- f71808e_wdt imporvements
- dw_wdt improvements
- mlx-wdt: support new watchdog type with longer timeout period
- fallthrough pseudo-keyword replacements
- overall small fixes and improvements
* tag 'linux-watchdog-5.9-rc1' of git://www.linux-watchdog.org/linux-watchdog: (35 commits)
watchdog: rti-wdt: balance pm runtime enable calls
watchdog: rti-wdt: attach to running watchdog during probe
watchdog: add support for adjusting last known HW keepalive time
watchdog: use __watchdog_ping in startup
watchdog: softdog: Add options 'soft_reboot_cmd' and 'soft_active_on_boot'
watchdog: pcwd_usb: remove needless check before usb_free_coherent()
watchdog: Replace HTTP links with HTTPS ones
dt-bindings: watchdog: renesas,wdt: Document r8a774e1 support
watchdog: initialize device before misc_register
watchdog: booke_wdt: Add common nowayout parameter driver
watchdog: scx200_wdt: Use fallthrough pseudo-keyword
watchdog: Use fallthrough pseudo-keyword
watchdog: f71808e_wdt: do stricter parameter validation
watchdog: f71808e_wdt: clear watchdog timeout occurred flag
watchdog: f71808e_wdt: remove use of wrong watchdog_info option
watchdog: f71808e_wdt: indicate WDIOF_CARDRESET support in watchdog_info.options
docs: watchdog: codify ident.options as superset of possible status flags
dt-bindings: watchdog: Add compatible for QCS404, SC7180, SDM845, SM8150
dt-bindings: watchdog: Convert QCOM watchdog timer bindings to YAML
watchdog: dw_wdt: Add DebugFS files
...
Linus Torvalds [Wed, 12 Aug 2020 18:53:01 +0000 (11:53 -0700)]
Merge tag 'drm-next-2020-08-12' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This has a few vmwgfx regression fixes we hit from the merge window
(one in TTM), it also has a bunch of amdgpu fixes along with a
scattering everywhere else.
core:
- Fix drm_dp_mst_port refcount leaks in drm_dp_mst_allocate_vcpi
- Remove null check for kfree in drm_dev_release.
- Fix DRM_FORMAT_MOD_AMLOGIC_FBC definition.
- re-added docs for drm_gem_flink_ioctl()
- add orientation quirk for ASUS T103HAF
fbcon:
- Fix a fbcon OOB read in fbdev, found by syzbot.
vga:
- Mark vga_tryget static as it's not used elsewhere.
amdgpu:
- Re-add spelling typo fix
- Sienna Cichlid fixes
- Navy Flounder fixes
- DC fixes
- SMU i2c fix
- Power fixes
vmwgfx:
- regression fixes for modesetting crashes
- misc fixes
xlnx:
- Small fixes to xlnx.
omap:
- Fix mode initialization in omap_connector_mode_valid().
- force runtime PM suspend on system suspend
tidss:
- fix modeset init for DPI panels"
* tag 'drm-next-2020-08-12' of git://anongit.freedesktop.org/drm/drm: (70 commits)
drm/ttm: revert "drm/ttm: make TT creation purely optional v3"
drm/vmwgfx: fix spelling mistake "Cant" -> "Can't"
drm/vmwgfx: fix spelling mistake "Cound" -> "Could"
drm/vmwgfx/ldu: Use drm_mode_config_reset
drm/vmwgfx/sou: Use drm_mode_config_reset
drm/vmwgfx/stdu: Use drm_mode_config_reset
drm/vmwgfx: Fix two list_for_each loop exit tests
drm/vmwgfx: Use correct vmw_legacy_display_unit pointer
drm/vmwgfx: Use struct_size() helper
drm/amdgpu: Fix bug where DPM is not enabled after hibernate and resume
drm/amd/powerplay: put VCN/JPEG into PG ungate state before dpm table setup(V3)
drm/amd/powerplay: update swSMU VCN/JPEG PG logics
drm/amdgpu: use mode1 reset by default for sienna_cichlid
drm/amdgpu/smu: rework i2c adpater registration
drm/amd/display: Display goes blank after inst
drm/amd/display: Change null plane state swizzle mode to 4kb_s
drm/amd/display: Use helper function to check for HDMI signal
drm/amd/display: AMD OUI (DPCD 0x00300) skipped on some sink
drm/amd/display: Fix logger context
drm/amd/display: populate new dml variable
...
Linus Torvalds [Wed, 12 Aug 2020 18:24:12 +0000 (11:24 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
- most of the rest of MM (memcg, hugetlb, vmscan, proc, compaction,
mempolicy, oom-kill, hugetlbfs, migration, thp, cma, util,
memory-hotplug, cleanups, uaccess, migration, gup, pagemap),
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
mm/gup: remove task_struct pointer for all gup code
mm: clean up the last pieces of page fault accountings
mm/xtensa: use general page fault accounting
mm/x86: use general page fault accounting
mm/sparc64: use general page fault accounting
mm/sparc32: use general page fault accounting
mm/sh: use general page fault accounting
mm/s390: use general page fault accounting
mm/riscv: use general page fault accounting
mm/powerpc: use general page fault accounting
mm/parisc: use general page fault accounting
mm/openrisc: use general page fault accounting
mm/nios2: use general page fault accounting
mm/nds32: use general page fault accounting
mm/mips: use general page fault accounting
mm/microblaze: use general page fault accounting
mm/m68k: use general page fault accounting
mm/ia64: use general page fault accounting
mm/hexagon: use general page fault accounting
mm/csky: use general page fault accounting
...
Peter Xu [Wed, 12 Aug 2020 01:38:57 +0000 (18:38 -0700)]
mm: clean up the last pieces of page fault accountings
Here're the last pieces of page fault accounting that were still done
outside handle_mm_fault() where we still have regs==NULL when calling
handle_mm_fault():
Some of them has the issue of duplicated accounting for page fault
retries. Some of them didn't do the accounting at all.
This patch cleans all these up by letting handle_mm_fault() to do per-task
page fault accounting even if regs==NULL (though we'll still skip the perf
event accountings). With that, we can safely remove all the outliers now.
There's another functional change in that now we account the page faults
to the caller of gup, rather than the task_struct that passed into the gup
code. More information of this can be found at [1].
After this patch, below things should never be touched again outside
handle_mm_fault():
Peter Xu [Wed, 12 Aug 2020 01:38:53 +0000 (18:38 -0700)]
mm/xtensa: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Remove the PERF_COUNT_SW_PAGE_FAULTS_[MAJ|MIN] perf events because it's
now also done in handle_mm_fault().
Move the PERF_COUNT_SW_PAGE_FAULTS event higher before taking mmap_sem for
the fault, then it'll match with the rest of the archs.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Cc: Chris Zankel <chris@zankel.net> Link: http://lkml.kernel.org/r/20200707225021.200906-24-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:46 +0000 (18:38 -0700)]
mm/sparc64: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Link: http://lkml.kernel.org/r/20200707225021.200906-22-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:43 +0000 (18:38 -0700)]
mm/sparc32: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: David S. Miller <davem@davemloft.net> Link: http://lkml.kernel.org/r/20200707225021.200906-21-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:40 +0000 (18:38 -0700)]
mm/sh: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Link: http://lkml.kernel.org/r/20200707225021.200906-20-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:37 +0000 (18:38 -0700)]
mm/s390: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Link: http://lkml.kernel.org/r/20200707225021.200906-19-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:34 +0000 (18:38 -0700)]
mm/riscv: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Pekka Enberg <penberg@kernel.org> Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Link: http://lkml.kernel.org/r/20200707225021.200906-18-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:28 +0000 (18:38 -0700)]
mm/parisc: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Add the missing PERF_COUNT_SW_PAGE_FAULTS perf events too. Note, the
other two perf events (PERF_COUNT_SW_PAGE_FAULTS_[MAJ|MIN]) were done in
handle_mm_fault().
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> Cc: Helge Deller <deller@gmx.de> Link: http://lkml.kernel.org/r/20200707225021.200906-16-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:25 +0000 (18:38 -0700)]
mm/openrisc: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Add the missing PERF_COUNT_SW_PAGE_FAULTS perf events too. Note, the
other two perf events (PERF_COUNT_SW_PAGE_FAULTS_[MAJ|MIN]) were done in
handle_mm_fault().
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Stafford Horne <shorne@gmail.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Link: http://lkml.kernel.org/r/20200707225021.200906-15-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:22 +0000 (18:38 -0700)]
mm/nios2: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Add the missing PERF_COUNT_SW_PAGE_FAULTS perf events too. Note, the
other two perf events (PERF_COUNT_SW_PAGE_FAULTS_[MAJ|MIN]) were done in
handle_mm_fault().
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Link: http://lkml.kernel.org/r/20200707225021.200906-14-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:19 +0000 (18:38 -0700)]
mm/nds32: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Fix PERF_COUNT_SW_PAGE_FAULTS perf event manually for page fault retries,
by moving it before taking mmap_sem.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Greentime Hu <green.hu@gmail.com> Cc: Nick Hu <nickhu@andestech.com> Cc: Vincent Chen <deanbo422@gmail.com> Link: http://lkml.kernel.org/r/20200707225021.200906-13-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:15 +0000 (18:38 -0700)]
mm/mips: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Fix PERF_COUNT_SW_PAGE_FAULTS perf event manually for page fault retries,
by moving it before taking mmap_sem.
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Link: http://lkml.kernel.org/r/20200707225021.200906-12-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Xu [Wed, 12 Aug 2020 01:38:12 +0000 (18:38 -0700)]
mm/microblaze: use general page fault accounting
Use the general page fault accounting by passing regs into
handle_mm_fault(). It naturally solve the issue of multiple page fault
accounting when page fault retry happened.
Add the missing PERF_COUNT_SW_PAGE_FAULTS perf events too. Note, the
other two perf events (PERF_COUNT_SW_PAGE_FAULTS_[MAJ|MIN]) were done in
handle_mm_fault().
Signed-off-by: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Simek <monstr@monstr.eu> Link: http://lkml.kernel.org/r/20200707225021.200906-11-peterx@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / kernel.git / log