When sysfs for no_turbo is set, then also some p states in turbo regions
are observed. This patch will set IDA Engage bit when no_turbo is set to
explicitly disengage turbo.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Philipp Zabel [Thu, 26 Sep 2013 09:19:37 +0000 (11:19 +0200)]
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
Since the patch "cpufreq: cpufreq-cpu0: NULL is a valid regulator", cpu_reg
contains an error value if the regulator is not set, instead of NULL.
Accordingly, fix the remaining check for non-NULL cpu_reg.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB driver fixes for 3.12-rc3.
These are all for host controller issues that have been reported, and
there's a fix for an annoying error message that gets printed every
time you remove a USB 3 device from the system that's been bugging me
for a while"
* tag 'usb-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: add support for Merrifield
USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
USB: Fix breakage in ffs_fs_mount()
fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
usb: chipidea: USB_CHIPIDEA should depend on HAS_DMA
usb: chipidea: udc: free pending TD at removal procedure
usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
usb: chipidea: Fix memleak for ci->hw_bank.regmap when removal
usb: chipidea: udc: fix the oops after rmmod gadget
USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
USB: OHCI: accept very late isochronous URBs
USB: UHCI: accept very late isochronous URBs
USB: iMX21: accept very late isochronous URBs
usbcore: check usb device's state before sending a Set SEL control transfer
xhci: Fix race between ep halt and URB cancellation
usb: Fix xHCI host issues on remote wakeup.
xhci: Ensure a command structure points to the correct trb on the command ring
xhci: Fix oops happening after address device timeout
Merge tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some serial at tty driver fixes for 3.12-rc3
The serial driver fixes some kref leaks, documentation is moved to the
proper places, and the tty and n_tty fixes resolve some reported
regressions. There is still one outstanding tty regression fix that
isn't in here yet, as I want to test it out some more, it will be sent
for 3.12-rc4 if it checks out"
* tag 'tty-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: ar933x_uart: move devicetree binding documentation
tty: Fix SIGTTOU not sent with tcflush()
n_tty: Fix EOF push index when termios changes
serial: pch_uart: remove unnecessary tty_port_tty_get
serial: pch_uart: fix tty-kref leak in dma-rx path
serial: pch_uart: fix tty-kref leak in rx-error path
serial: tegra: fix tty-kref leak
Merge tag 'staging-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some staging driver fixes, MAINTAINER updates, and a new
device id. All of these have been in the linux-next tree, and are
pretty simple patches"
* tag 'staging-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID
staging: imx-drm: Fix probe failure
staging: vt6656: [BUG] iwctl_siwencodeext return if device not open
staging: vt6656: [BUG] main_usb.c oops on device_close move flag earlier.
staging: vt6656: rxtx.c [BUG] s_vGetFreeContext dead lock on null apTD.
Staging: rtl8192u: r819xU_cmdpkt: checking NULL value after doing dev_alloc_skb
staging: usbip: Orphan usbip
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
staging: r8188eu: Cocci spatch "noderef"
staging: octeon-usb: Cocci spatch "noderef"
staging: r8188eu: Add files for new drive: Cocci spatch "noderef"
MAINTAINERS: staging: dgnc and dgap drivers: add maintainer
staging: lustre: Cocci spatch "noderef"
Merge tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs fixes from Greg KH:
"Here are 2 fixes for 3.12-rc3. One fixes a sysfs problem with
mounting caused by 3.12-rc1, and the other is a bug reported by the
chromeos developers with the driver core.
Both have been in linux-next for a bit"
* tag 'driver-core-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core : Fix use after free of dev->parent in device_shutdown
sysfs: Allow mounting without CONFIG_NET
Merge tag 'char-misc-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some HyperV and MEI driver fixes for 3.12-rc3. They resolve
some issues that people have been reporting for them"
* tag 'char-misc-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Terminate vmbus version negotiation on timeout
Drivers: hv: util: Correctly support ws2008R2 and earlier
mei: cancel stall timers in mei_reset
mei: bus: stop wait for read during cl state transition
mei: make me client counters less error prone
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too major, radeon still has some dpm changes for off by
default.
Radeon, intel, msm:
- radeon: a few more dpm fixes (still off by default), uvd fixes
- i915: runtime warn backtrace and regression fix
- msm: iommu changes fallout"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (27 commits)
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
drm/i915: Fix up usage of SHRINK_STOP
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/i915: Use a temporary va_list for two-pass string handling
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
...
Markus Trippelsdorf reported that this commit broke 'perf top':
> I just see a gray screen with no text at all. Sometimes the
> following error messages are printed:
>
> *** Error in `perf': invalid fastbin entry (free): 0x00000000029b18c0
> ***
> *** Error in `perf': malloc(): memory corruption (fast): 0x0000000000ee0b10 ***
While this code is fixable, the commit itself fails on several levels:
- it should have been a separate helper function
- why the heck does it do strchr() twice
- it casts a const char * over into char *
- sloppy style
- it's not even a regression fix!
So lets revert it and re-try the patch in v3.13.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de> Cc: Andi Kleen <ak@linux.intel.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Airlie [Sun, 29 Sep 2013 00:06:28 +0000 (10:06 +1000)]
Merge branch 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux into drm-fixes
A small fix + deal with fallout of iommu changes + use new
drm_gem_dumb_destroy helper.
* 'msm-fixes-3.12-rc2' of git://people.freedesktop.org/~robclark/linux:
drm/msm: use drm_gem_dumb_destroy helper
drm/msm: deal with mach/iommu.h removal
drm/msm: Remove iommu include from mdp4_kms.c
drm/msm: Odd PTR_ERR usage
Merge branches 'sched-urgent-for-linus', 'timers-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of tooling fixlets and a PMU detection printout fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix PMU detection printout when no PMU is detected
perf symbols: Demangle cloned functions
perf machine: Fix path unpopulated in machine__create_modules()
perf tools: Explicitly add libdl dependency
perf probe: Fix probing symbols with optimization suffix
perf trace: Add mmap2 handler
perf kmem: Make it work again on non NUMA machines
Merge tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
- fix for directory node collapse regression
- fix for recovery over stale on disk structures
- fix for eofblocks ioctl
- fix asserts in xfs_inode_free
- lock the ail before removing an item from it
* tag 'xfs-for-linus-v3.12-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: fix node forward in xfs_node_toosmall
xfs: log recovery lsn ordering needs uuid check
xfs: fix XFS_IOC_FREE_EOFBLOCKS definition
xfs: asserting lock not held during freeing not valid
xfs: lock the AIL before removing the buffer item
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: initialize DMA buffer
i2c: designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set
i2c: mv64xxx: Do not use writel_relaxed()
i2c: mv64xxx: Fix some build warnings
i2c: s3c2410: fix clk_disable/clk_unprepare WARNings
Merge tag 'pm+acpi-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These fix one recent cpufreq regression, a few older bugs that may
harm users and a kerneldoc typo.
Specifics:
1) After the recent locking changes in the cpufreq core it is
possible to trigger BUG_ON(!policy) in lock_policy_rwsem_read() if
cpufreq_get() is called before registering a cpufreq driver. Fix
from Viresh Kumar.
2) If intel_pstate has been loaded already, it doesn't make sense to
do anything in acpi_cpufreq_init() and moreover doing something in
there in that case may be harmful, so make that function return
immediately if another cpufreq driver is already present. From
Yinghai Lu.
3) The ACPI IPMI driver sometimes attempts to acquire a mutex from
interrupt context, which can be avoided by replacing that mutex
with a spinlock. From Lv Zheng.
4) A NULL pointer may be dereferenced by the exynos5440 cpufreq
driver if a memory allocation made by it fails. Fix from Sachin
Kamat.
5) Hanjun Guo's commit fixes a typo in the kerneldoc comment
documenting acpi_bus_unregister_driver()"
* tag 'pm+acpi-3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: fix typo in comments of acpi_bus_unregister_driver()
cpufreq: exynos5440: Fix potential NULL pointer dereference
cpufreq: check cpufreq driver is valid and cpufreq isn't disabled in cpufreq_get()
acpi-cpufreq: skip loading acpi_cpufreq after intel_pstate
ACPI / IPMI: Fix atomic context requirement of ipmi_msg_handler()
Yinghai Lu [Sat, 28 Sep 2013 20:13:07 +0000 (13:13 -0700)]
PCI: Workaround missing pci_set_master in pci drivers
Ben Herrenschmidt found that commit d82e87efee34 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.
The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.
Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.
Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.
That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'lockref' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 lockref enablement from Heiko Carstens:
"Enabling the new lockless lockref variant on s390 would have been
trivial until Tony Luck added a cpu_relax() call into the
CMPXCHG_LOOP(), with commit ea39c50d3849 ("lockref: Relax in cmpxchg
loop")
As already mentioned cpu_relax() is very expensive on s390 since it
yields() the current virtual cpu. So we are talking of several
thousand cycles. Considering this enabling the lockless lockref
variant would contradict the intention of the new semantics. And also
some quick measurements show performance regressions of 50% and more.
Simply removing the cpu_relax() call again seems also not very
desireable since Waiman Long reported that for some workloads the call
improved performance by 5%."
* 'lockref' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: enable ARCH_USE_CMPXCHG_LOCKREF
lockref: use arch_mutex_cpu_relax() in CMPXCHG_LOOP()
mutex: replace CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX with simple ifdef
Jean Delvare [Fri, 27 Sep 2013 20:17:39 +0000 (13:17 -0700)]
kernel/params: fix handling of signed integer types
Commit fb47fc7157ab ("kernel: replace strict_strto*() with kstrto*()")
broke the handling of signed integer types, fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Reported-by: Christian Kujau <lists@nerdbynature.de> Tested-by: Christian Kujau <lists@nerdbynature.de> Cc: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
"Clean-up to fix some warnings for !OF builds and spelling fixes in
docs:
- Clean-up openrisc prom.h
- Fix warnings caused by of_irq.h ifdefs
- Spelling fix for Synopsys"
* tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: Fix misspelling of Synopsys
of: clean-up ifdefs in of_irq.h
openrisc: clean-up prom.h
Rob Clark [Sat, 28 Sep 2013 14:07:06 +0000 (10:07 -0400)]
drm/msm: deal with mach/iommu.h removal
We still need an API exported by msm iommu driver (but not visible in
any public header anymore). For now, just declare the prototype
ourselves, but when msm iommu driver provides a better option, use that
instead.
lockref: use arch_mutex_cpu_relax() in CMPXCHG_LOOP()
Make use of arch_mutex_cpu_relax() so architectures can override the
default cpu_relax() semantics.
This is especially useful for s390, where cpu_relax() means that we
yield() the current (virtual) cpu and therefore is very expensive,
and would contradict the whole purpose of the lockless cmpxchg loop.
to get rid of CONFIG_HAVE_CPU_RELAX_SIMPLE. So architectures can
simply define arch_mutex_cpu_relax if they want an architecture
specific function instead of having to add a select statement in
their Kconfig in addition.
Dave Airlie [Sat, 28 Sep 2013 04:45:30 +0000 (14:45 +1000)]
Merge branch 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
More radeon fixes for 3.12. Kind of all over the place: UVD, DPM,
tiling, etc.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
drm/radeon: fix missed variable sized access
drm/radeon: Make r100_cp_ring_info() and radeon_ring_gfx() safe (v2)
drm/radeon/cik: Add tiling mode index for 1D tiled depth/stencil surfaces
drm/radeon/cik: Fix encoding of number of banks in tiling configuration info
drm/radeon/cik: Fix printing of client name on VM protection fault
drm/radeon: additional gcc fixes for radeon_atombios.c
drm/radeon: avoid UVD corruption on AGP cards using GPU gart
Dave Airlie [Fri, 27 Sep 2013 22:46:44 +0000 (08:46 +1000)]
Merge tag 'drm-intel-fixes-2013-09-26' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Just a few fixes for regressions and other serious stuff.
Two fix state tracking mismatches, together with an additional patch that
I've submitted to stable (somehow forgotten to tag it) we should have them
fixed now (I hope).
* tag 'drm-intel-fixes-2013-09-26' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix up usage of SHRINK_STOP
drm/i915: preserve pipe A quirk in i9xx_set_pipeconf
drm/i915/tv: clear adjusted_mode.flags
drm/i915/dp: increase i2c-over-aux retry interval on AUX DEFER
drm/i915: Use a temporary va_list for two-pass string handling
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing too serious here: a couple of compress-offload core fixes,
Haswell HDMI audio fix, a fixup for new MacBook Airs and a few COEF
setups for ALC283 mic problems"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Enable internal mic on a Thinkpad machine with ALC283
ALSA: hda - Fix Internal Mic boost can't control with ALC283
ALSA: hda - Add documentation for CS4208 fixups
ALSA: hda - Add fixup for MacBook Air 6,1 and 6,2 with CS4208 codec
ALSA : hda - not use assigned converters for all unused pins
ALSA: compress: Make sure we trigger STOP before closing the stream.
ALSA: compress: Fix compress device unregister.
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull reiserfs and UDF fixes from Jan Kara:
"The contains fix of an UDF oops when mounting corrupted media and a
fix of a race in reiserfs leading to oops"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: fix race with flush_used_journal_lists and flush_journal_list
reiserfs: remove useless flush_old_journal_lists
udf: Fortify LVID loading
In kobj_ns_current_may_mount the default should be to allow the mount.
The test is only for a single kobj_ns_type at a time, and unless there
is a reason to prevent it the mounting sysfs should be allowed.
Subsystems that are not registered can't have are not involved so can't
have a reason to prevent mounting sysfs.
This is a bug-fix to commit f5106370cff6 ("sysfs: Restrict mounting
sysfs") that came in via the userns tree during the 3.12 merge window.
Reported-and-tested-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Thu, 26 Sep 2013 16:27:00 +0000 (17:27 +0100)]
lockref: allow relaxed cmpxchg64 variant for lockless updates
The 64-bit cmpxchg operation on the lockref is ordered by virtue of
hazarding between the cmpxchg operation and the reference count
manipulation. On weakly ordered memory architectures (such as ARM), it
can be of great benefit to omit the barrier instructions where they are
not needed.
This patch moves the lockless lockref code over to a cmpxchg64_relaxed
operation, which doesn't provide barrier semantics. If the operation
isn't defined, we simply #define it as the usual 64-bit cmpxchg macro.
Cc: Waiman Long <Waiman.Long@hp.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2c: designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver is used on PowerPC which don't provide writel_relaxed(). This
breaks the c2k and prpmc2800 default configurations. To fix the build,
turn the calls to writel_relaxed() into writel(). The impacts for ARM
should be minimal.
Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some functions and variables are only used if the configuration selects
HAVE_CLK. Protect them with a corresponding #ifdef CONFIG_HAVE_CLK block
to avoid compiler warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[wsa: added marker to #endif] Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit bfabc84b12216d8af3654e8f077ade87e3dbcdd7 "i2c: s3c2410: Move
location of clk_prepare_enable() call in probe function" refactored
clk_enable and clk_disable calls yet neglected to remove the
clk_disable_unprepare call in the module's remove().
It helps remove warnings on an arndale during unbind:
7c5fed5616ab (context_tracking: Optimize main APIs off case
with static key) converted context tracking main APIs to inline
function and left ARM asm callers behind.
This can be easily fixed by making ARM calling the post static
keys context tracking function. We just need to replicate the
static key checks there. We'll remove these later when ARM will
support the context tracking static keys.
Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com> Tested-by: Kevin Hilman <khilman@linaro.org> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Anil Kumar <anilk4.v@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Russell King <linux@arm.linux.org.uk> Cc: Kevin Hilman <khilman@linaro.org>
Kailang Yang [Fri, 27 Sep 2013 12:02:28 +0000 (14:02 +0200)]
ALSA: hda - Fix Internal Mic boost can't control with ALC283
ALC283 pin control for Line1 default control by hidden register.
Use line1 as internal Mic will not get sound when boost value up.
Set control by verb for hidden register will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ben Whitten [Fri, 27 Sep 2013 08:13:51 +0000 (10:13 +0200)]
ALSA: hda - Add fixup for MacBook Air 6,1 and 6,2 with CS4208 codec
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811 Signed-off-by: Ben Whitten <benwhitten@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
x86/microcode/AMD: Fix patch level reporting for family 15h
On AMD family 14h, applying microcode patch on the a core (core0)
would also affect the other core (core1) in the same compute
unit. The driver would skip applying the patch on core1, but it
still need to update kernel structures to reflect the proper
patch level.
The current logic is not updating the struct
ucode_cpu_info.cpu_sig.rev of the skipped core. This causes the
/sys/devices/system/cpu/cpu1/microcode/version to report
incorrect patch level as shown below:
Shengzhou Liu [Mon, 2 Sep 2013 05:25:52 +0000 (13:25 +0800)]
USB: fsl/ehci: fix failure of checking PHY_CLK_VALID during reinitialization
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Fri, 20 Sep 2013 16:14:21 +0000 (17:14 +0100)]
USB: Fix breakage in ffs_fs_mount()
There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics. Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been. ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().
Current behaviour of ffs_fs_mount():
We have struct ffs_sb_fill_data data on stack there. We do
ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data. Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback. That will either fail
outright, or manage to call ffs_sb_fill(). There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data). Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there). Any of those might fail. Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns. If mount_nodev() fails for any reason whatsoever,
we proceed to
functionfs_release_dev_callback(data.ffs_data);
That's broken in a lot of ways. Suppose the thing has failed in
allocation of e.g. root inode or dentry. We have
functionfs_release_dev_callback(ffs);
ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data). Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.
Suppose we fail *before* root inode allocation. What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info). And
functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into. In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.
FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.
The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data. And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: stable <stable@vger.kernel.org> # 3.3+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
driver core : Fix use after free of dev->parent in device_shutdown
The put_device(dev) at the bottom of the loop of device_shutdown
may result in the dev being cleaned up. In device_create_release,
the dev is kfreed.
However, device_shutdown attempts to use the dev pointer again after
put_device by referring to dev->parent.
Copy the parent pointer instead to avoid this condition.
This bug was found on Chromium OS's chromeos-3.8, which is based on v3.8.11.
See bug report : https://code.google.com/p/chromium/issues/detail?id=297842
This can easily be reproduced when shutting down with
hidraw devices that report battery condition.
Two examples are the HP Bluetooth Mouse X4000b and the Apple Magic Mouse.
For example, with the magic mouse :
The dev in question is "hidraw0"
dev->parent is "magicmouse"
In the course of the shutdown for this device, the input event cleanup calls
a put on hidraw0, decrementing its reference count.
When we finally get to put_device(dev) in device_shutdown, kobject_cleanup
is called and device_create_release does kfree(dev).
dev->parent is no longer valid, and we may crash in
put_device(dev->parent).
In kobj_ns_current_may_mount the default should be to allow the
mount. The test is only for a single kobj_ns_type at a time, and unless
there is a reason to prevent it the mounting sysfs should be allowed.
Subsystems that are not registered can't have are not involved so can't
have a reason to prevent mounting sysfs.
Don't allow mounting sysfs unless the caller has CAP_SYS_ADMIN rights
over the net namespace. The principle here is if you create or have
capabilities over it you can mount it, otherwise you get to live with
what other people have mounted.
Instead of testing this with a straight forward ns_capable call,
perform this check the long and torturous way with kobject helpers,
this keeps direct knowledge of namespaces out of sysfs, and preserves
the existing sysfs abstractions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
That came in via the userns tree during the 3.12 merge window.
Reported-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: vmbus: Terminate vmbus version negotiation on timeout
commit 1bb341dee3b78fd6e0bf250519a692f734e73bec terminated vmbus
version negotiation incorrectly. We need to terminate the version
negotiation only if the current negotiation were to timeout.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Olaf Hering <ohering@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers: hv: util: Correctly support ws2008R2 and earlier
The current code does not correctly negotiate the version numbers for the util
driver when hosted on earlier hosts. The version numbers presented by this
driver were not compatible with the version numbers supported by Windows Server
2008. Fix this problem.
I would like to thank Olaf Hering (ohering@suse.com) for identifying the problem.
Reported-by: Olaf Hering <ohering@suse.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Mon, 2 Sep 2013 10:29:46 +0000 (13:29 +0300)]
mei: bus: stop wait for read during cl state transition
Bus layer omitted check for client state transition while waiting
for read completion
The client state transition may occur for example as result
of firmware initiated reset
Add mei_cl_is_transitioning wrapper to reduce the code
repetition.:
fsl/usb: Resolve PHY_CLK_VLD instability issue for ULPI phy
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Mark Tinguely [Mon, 23 Sep 2013 17:18:58 +0000 (12:18 -0500)]
xfs: fix node forward in xfs_node_toosmall
Commit 42a65bd7 cleans up the disk to host conversions for
node directory entries, but because a variable is reused in
xfs_node_toosmall() the next node is not correctly found.
If the original node is small enough (<= 3/8 of the node size),
this change may incorrectly cause a node collapse when it should
not. That will cause an assert in xfstest generic/319:
Assertion failed: first <= last && last < BBTOB(bp->b_length),
file: /root/newest/xfs/fs/xfs/xfs_trans_buf.c, line: 569
Keep the original node header to get the correct forward node.
(When a node is considered for a merge with a sibling, it overwrites the
sibling pointers of the original incore nodehdr with the sibling's
pointers. This leads to loop considering the original node as a merge
candidate with itself in the second pass, and so it incorrectly
determines a merge should occur.)
Signed-off-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
[v3: added Dave Chinner's (slightly modified) suggestion to the commit header,
cleaned up whitespace. -bpm]
Henrik Rydberg [Thu, 26 Sep 2013 06:33:16 +0000 (08:33 +0200)]
hwmon: (applesmc) Check key count before proceeding
After reports from Chris and Josh Boyer of a rare crash in applesmc,
Guenter pointed at the initialization problem fixed below. The patch
has not been verified to fix the crash, but should be applied
regardless.
of_get_display_timing(s) use of_find_node_by_name
to get child node, this is incorrect, of_get_child_by_name
should be used instead. The patch fixes it.
Small typo is also corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The nice thing about devm_* is that the driver doesn't need to free the
resources but the driver core takes care about that. This also
simplifies the error path quite a bit and removes the wrong check for a
clock pointer being NULL.
Russell King - ARM Linux <linux@arm.linux.org.uk>:
"And this patch also fixes the above: disabling/unpreparing _after_ putting
the thing - which was quite silly... :)"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mengdong Lin [Sun, 22 Sep 2013 00:34:45 +0000 (20:34 -0400)]
ALSA : hda - not use assigned converters for all unused pins
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Reviewed-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: compress: Make sure we trigger STOP before closing the stream.
Currently we assume that userspace will shut down the compressed stream
correctly. However, if userspcae dies (e.g. cplay & ctrl-C) we dont
stop the stream before freeing it.
This now checks that the stream is stopped before freeing.
Peter Hurley [Thu, 26 Sep 2013 00:13:04 +0000 (20:13 -0400)]
tty: Fix SIGTTOU not sent with tcflush()
Commit '3b92e7bf4661e7bb2610b5b12137ba8158b6ca11'
tty: Fix recursive deadlock in tty_perform_flush()
introduced a regression where tcflush() does not generate
SIGTTOU for background process groups.
Make sure ioctl(TCFLSH) calls tty_check_change() when
invoked from the line discipline.
Magnus Damm [Wed, 18 Sep 2013 20:01:16 +0000 (15:01 -0500)]
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
Update the STI driver by setting cpu_possible_mask to make EMEV2
SMP work as expected together with the ARM broadcast timer.
This breakage was introduced by:
34154a5 ARM: 7674/1: smp: Avoid dummy clockevent being preferred over real hardware clock-event
Without this fix SMP operation is broken on EMEV2 since no
broadcast timer interrupts trigger on the secondary CPU cores.
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Kurt Garloff [Tue, 24 Sep 2013 12:13:48 +0000 (14:13 +0200)]
usb/core/devio.c: Don't reject control message to endpoint with wrong direction bit
Trying to read data from the Pegasus Technologies NoteTaker (0e20:0101)
[1] with the Windows App (EasyNote) works natively but fails when
Windows is running under KVM (and the USB device handed to KVM).
The reason is a USB control message
usb 4-2.2: control urb: bRequestType=22 bRequest=09 wValue=0200 wIndex=0001 wLength=0008
This goes to endpoint address 0x01 (wIndex); however, endpoint address
0x01 does not exist. There is an endpoint 0x81 though (same number,
but other direction); the app may have meant that endpoint instead.
The kernel thus rejects the IO and thus we see the failure.
Apparently, Linux is more strict here than Windows ... we can't change
the Win app easily, so that's a problem.
It seems that the Win app/driver is buggy here and the driver does not
behave fully according to the USB HID class spec that it claims to
belong to. The device seems to happily deal with that though (and
seems to not really care about this value much).
So the question is whether the Linux kernel should filter here.
Rejecting has the risk that somewhat non-compliant userspace apps/
drivers (most likely in a virtual machine) are prevented from working.
Not rejecting has the risk of confusing an overly sensitive device with
such a transfer. Given the fact that Windows does not filter it makes
this risk rather small though.
The patch makes the kernel more tolerant: If the endpoint address in
wIndex does not exist, but an endpoint with toggled direction bit does,
it will let the transfer through. (It does NOT change the message.)
With attached patch, the app in Windows in KVM works.
usb 4-2.2: check_ctrlrecip: process 13073 (qemu-kvm) requesting ep 01 but needs 81
I suspect this will mostly affect apps in virtual environments; as on
Linux the apps would have been adapted to the stricter handling of the
kernel. I have done that for mine[2].
Peter Chen [Tue, 17 Sep 2013 04:37:24 +0000 (12:37 +0800)]
usb: chipidea: udc: free pending TD at removal procedure
There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.
This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Tue, 17 Sep 2013 04:37:23 +0000 (12:37 +0800)]
usb: chipidea: imx: Add usb_phy_shutdown at probe's error path
If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Tue, 17 Sep 2013 04:37:20 +0000 (12:37 +0800)]
usb: chipidea: udc: fix the oops after rmmod gadget
When we rmmod gadget, the ci->driver needs to be cleared.
Otherwise, when we plug in usb cable again, the driver will
consider gadget is there, and go to enumeration procedure,
but in fact, it was removed.
Clocksource devices provided by DT can be disabled (status != "okay").
Instead of registering clocksource drivers for disabled nodes, respect
the device's status by skiping disabled nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tomasz Figa [Wed, 25 Sep 2013 10:00:59 +0000 (12:00 +0200)]
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
Some variants of Exynos MCT, namely exynos4210-mct at the moment, use
normal, shared interrupts for local timers. This means that each
interrupt must have correct affinity set to fire only on CPU
corresponding to given local timer.
However after recent conversion of clocksource drivers to not use the
local timer API for local timer initialization any more, the point of
time when local timers get initialized changed and irq_set_affinity()
fails because the CPU is not marked as online yet.
This patch fixes this by moving the call to irq_set_affinity() to
CPU_ONLINE notification, so the affinity is being set when the CPU goes
online.
This fixes a regression introduced by commit b37a720f10 ARM: EXYNOS4: Divorce mct from local timer API
which rendered all Exynos4210 based boards unbootable due to
failing irq_set_affinity() making local timers inoperatible.
Signed-off-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Alan Stern [Tue, 24 Sep 2013 19:45:25 +0000 (15:45 -0400)]
USB: fix PM config symbol in uhci-hcd, ehci-hcd, and xhci-hcd
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 24 Sep 2013 19:46:45 +0000 (15:46 -0400)]
USB: OHCI: accept very late isochronous URBs
Commit 4a77405f60f9 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 1f43561de51c
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 24 Sep 2013 19:47:20 +0000 (15:47 -0400)]
USB: UHCI: accept very late isochronous URBs
Commit 4a77405f60f9 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit e263b33348f5 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 24 Sep 2013 19:48:05 +0000 (15:48 -0400)]
USB: iMX21: accept very late isochronous URBs
Commit 4a77405f60f9 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Sascha Hauer <kernel@pengutronix.de> CC: Martin Fuzzey <mfuzzey@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'for-usb-linus-2013-09-23' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Bug fixes for 3.12.
Hi Greg,
Here's five bug fixes for 3.12.
The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers. People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.
The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS. As discussed, this fix is not
urgent, and isn't marked for stable.
The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall. The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.
Since commit b117a982 (drm/imx: kill firstopen callback) the following probe
failure is seen:
[drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[drm] No driver support for vblank timestamp query.
[drm] Initialized imx-drm 1.0.0 20120507 on minor 0
imx-ldb ldb.10: adding encoder failed with -16
imx-ldb: probe of ldb.10 failed with error -16
imx-ipuv3 2400000.ipu: IPUv3H probed
imx-ipuv3 2800000.ipu: IPUv3H probed
imx-ipuv3-crtc imx-ipuv3-crtc.0: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.0 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.1: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.1 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.2: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.2 failed with error -16
imx-ipuv3-crtc imx-ipuv3-crtc.3: adding crtc failed with -16.
imx-ipuv3-crtc: probe of imx-ipuv3-crtc.3 failed with error -16
The reason for the probe failure is that now 'imxdrm->references' is incremented
early in imx_drm_driver_load(), so the following checks in imx_drm_add_crtc()
and imx_drm_add_encoder():
if (imxdrm->references) {
ret = -EBUSY;
goto err_busy;
}
,will always fail.
Instead of manually keeping the references in the imx-drm driver, let's use
drm->open_count.
After this patch, lvds panel is functional on a mx6qsabrelite board.
staging: vt6656: [BUG] main_usb.c oops on device_close move flag earlier.
The vt6656 is prone to resetting on the usb bus.
It seems there is a race condition and wpa supplicant is
trying to open the device via iw_handlers before its actually
closed at a stage that the buffers are being removed.
The device is longer considered open when the
buffers are being removed. So move ~DEVICE_FLAGS_OPENED
flag to before freeing the device buffers.
projects / kernel.git / log