Kalle Valo [Fri, 29 May 2020 17:42:30 +0000 (20:42 +0300)]
Merge tag 'mt76-for-kvalo-2020-05-28' of https://github.com/nbd168/wireless
mt76 patches for 5.8
* fixes for sparse warnings
* DBDC fixes
* mt7663 remain-on-channel support
* mt7915 spatial reuse support
* mt7915 radiotap fix
* station wcid allocation fix
* mt7663 powersave fix
* mt7663 scan fix
* mt7611n support
* cleanup
# gpg: Signature made Thu 28 May 2020 07:02:21 PM EEST using DSA key ID 02A76EF5
# gpg: Good signature from "Felix Fietkau <nbd@nbd.name>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
Dan Carpenter [Wed, 27 May 2020 18:48:30 +0000 (21:48 +0300)]
airo: Fix read overflows sending packets
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.
The fix is to pad skb->data to at least ETH_ZLEN bytes.
Cc: <stable@vger.kernel.org> Reported-by: Hu Jiahui <kirin.say@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda
Frank Kao [Fri, 29 May 2020 03:49:36 +0000 (22:49 -0500)]
brcmfmac: set F2 blocksize and watermark for 4354/4356 SDIO
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Dinghao Liu [Fri, 22 May 2020 04:49:04 +0000 (12:49 +0800)]
wlcore: fix runtime pm imbalance in wlcore_irq_locked
When wlcore_fw_status() returns an error code, a pairing
runtime PM usage counter decrement is needed to keep the
counter balanced. It's the same for all error paths after
wlcore_fw_status().
Chien-Hsun Liao [Fri, 22 May 2020 09:12:34 +0000 (17:12 +0800)]
rtw88: 8822c: remove CCK TX setting when switch channel
The CCK TX setting when switch channel will fix the CCK to
path A only, so if the antenna is configured to path B
(e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK
packets can never be delivered to the air if only path B is
connected with an antenna (it can possibly be transmitted
through path A, but as path B is configured, the expected
behavior is incorrect).
This can also solve the racing issue of CCK TX setting between
driver and firmware. The CCK TX setting in driver should be
removed. Otherwise, the CCK TX setting would be wrong when the
racing occurs.
Fixes: 7b0a0552a106 ("rtw88: add support for set/get antennas") Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200522091234.24495-1-yhchuang@realtek.com
Yan-Hsuan Chuang [Fri, 22 May 2020 03:55:21 +0000 (11:55 +0800)]
rtw88: 8822c: fix missing brace warning for old compilers
For older versions of gcc, the array = {0}; will cause warnings:
drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim':
>> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning:
>> missing braces around initializer [-Wmissing-braces]
s8 bb_gain[2][8] = {0};
^
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near
initialization for 'bb_gain[0]') [-Wmissing-braces]
Fixes: 96d491ce310f ("rtw88: set power trim according to efuse PG values") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
Ping-Ke Shih [Fri, 29 May 2020 02:50:09 +0000 (10:50 +0800)]
rtw88: fix EAPOL 4-way failure by finish IQK earlier
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: fda8a5ded852 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Ping-Ke Shih [Fri, 29 May 2020 02:50:08 +0000 (10:50 +0800)]
rtw88: coex: 8723d: handle BT inquiry cases
Coex mechanism used to make BT have higher priority and more time to
transfer data when BT inquiry-page, which leads to poor WiFi performance.
Should take WiFi traffic into consideration. If the WiFi is having heavy
traffic, use another parameter to make sure WiFi has more chance to TX/RX,
while guarantee the priority of BT for inquiry. If the WiFi isn't busy
(connected or not), set proper parameter to fix originals.
Fixes: fda8a5ded852 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200529025009.2468-3-yhchuang@realtek.com
Ping-Ke Shih [Fri, 29 May 2020 02:50:07 +0000 (10:50 +0800)]
rtw88: coex: 8723d: set antanna control owner
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: fda8a5ded852 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
Dinghao Liu [Wed, 20 May 2020 12:46:47 +0000 (20:46 +0800)]
wlcore: fix runtime pm imbalance in wlcore_regdomain_config
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Dinghao Liu [Wed, 20 May 2020 12:42:38 +0000 (20:42 +0800)]
wlcore: fix runtime pm imbalance in wl1271_tx_work
There are two error handling paths in this functon. When
wlcore_tx_work_locked() returns an error code, we should
decrease the runtime PM usage counter the same way as the
error handling path beginning from pm_runtime_get_sync().
Larry Finger [Tue, 26 May 2020 15:59:09 +0000 (10:59 -0500)]
b43_legacy: Fix connection problem with WPA3
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Larry Finger [Tue, 26 May 2020 15:59:08 +0000 (10:59 -0500)]
b43: Fix connection problem with WPA3
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
I am leaving Quantenna, so I will no longer have access to firmware and
hardware. Meanwhile I plan to participate in reviewing qtnfmac patches
for a while until my firmware knowledge becomes completely obsolete.
Adding myself as a reviewer using my personal email address.
Rui Salvaterra [Mon, 25 May 2020 13:49:07 +0000 (14:49 +0100)]
rt2800: enable MFP support unconditionally
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c: In function 'mt7915_mcu_sta_txbf_type':
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1805:21: warning:
variable 'msta' set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Sean Wang <sean.wang@mediatek.com> Fixes: bf3cb1b30b9c ("mt76: add HE phy modes and hardware queue") Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 23 May 2020 12:40:57 +0000 (14:40 +0200)]
mt76: fix wcid allocation issues
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Reported-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Sean Wang [Fri, 22 May 2020 07:10:24 +0000 (09:10 +0200)]
mt76: mt7615: fix hw_scan with ssid_type for specified SSID only
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Tue, 19 May 2020 08:42:11 +0000 (10:42 +0200)]
mt76: mt7615: switch to per-vif power_save support
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Mon, 18 May 2020 18:07:38 +0000 (02:07 +0800)]
mt76: mt7915: fix some sparse warnings
drivers/net/wireless/mediatek/mt76/mt7915/main.c:694:1: sparse:
sparse: context imbalance in 'mt7915_sta_rc_update' - wrong count at exit
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:303:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:304:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:305:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:319:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:327:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:345:41: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:355:33: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: sparse: invalid assignment: |=
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: left side has type unsigned int
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: right side has type restricted __le32
Fixes: c30b8a606f8f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 20 May 2020 06:04:47 +0000 (08:04 +0200)]
mt76: fix per-driver wcid range checks after wcid array size bump
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 637f5d60c86b ("mt76: adjust wcid size to support new 802.11ax generation") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Sat, 16 May 2020 09:05:18 +0000 (17:05 +0800)]
mt76: mt7915: fix some sparse warnings
This fixes the following sparse warning:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:253:16: sparse: sparse: mixing different enum types:
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:253:16: sparse: unsigned int enum mt7915_txq_id
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:253:16: sparse: unsigned int enum mt76_txq_id
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:758:63: sparse: sparse: incorrect type in argument 2 (different address spaces)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:758:63: sparse: expected unsigned char const [usertype] *ies
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:758:63: sparse: got unsigned char const [noderef] <asn:4> *
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1390:23: sparse: sparse: incorrect type in argument 1 (different base types)
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1390:23: sparse: expected unsigned int w
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1390:23: sparse: got restricted __le32 [usertype] supp_ht_mcs
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1390:23: sparse: sparse: restricted __le32 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1429:60: sparse: sparse: bad assignment (>>=) to restricted __le16
drivers/net/wireless/mediatek/mt76/mt7915/mcu.c:1773:16: sparse: sparse: restricted __le32 degrades to integer
Fixes: 8803c0af1a6e ("mt76: mt7915: add HE bss_conf support for interfaces") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Fri, 15 May 2020 17:03:42 +0000 (19:03 +0200)]
mt76: mt7615: introduce remain_on_channel support
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Tariq Toukan [Wed, 27 May 2020 09:25:26 +0000 (12:25 +0300)]
net/tls: Add force_resync for driver resync
This patch adds a field to the tls rx offload context which enables
drivers to force a send_resync call.
This field can be used by drivers to request a resync at the next
possible tls record. It is beneficial for hardware that provides the
resync sequence number asynchronously. In such cases, the packet that
triggered the resync does not contain the information required for a
resync. Instead, the driver requests resync for all the following
TLS record until the asynchronous notification with the resync request
TCP sequence arrives.
A following series for mlx5e ConnectX-6DX TLS RX offload support will
use this mechanism.
Signed-off-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net_sched: reduce the number of qdisc resets
This patchset aims to reduce the number of qdisc resets during
qdisc tear down. Patch 1~3 are preparation for their following
patches, especially patch 2 and patch 3 add a few tracepoints
so that we can observe the whole lifetime of qdisc's. Patch 4
and patch 5 are the ones do the actual work. Please find more
details in each patch description.
Vaclav Zindulka tested this patchset and his large ruleset with
over 13k qdiscs defined got from 22s to 520ms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Wed, 27 May 2020 04:35:27 +0000 (21:35 -0700)]
net_sched: get rid of unnecessary dev_qdisc_reset()
Resetting old qdisc on dev_queue->qdisc_sleeping in
dev_qdisc_reset() is redundant, because this qdisc,
even if not same with dev_queue->qdisc, is reset via
qdisc_put() right after calling dev_graft_qdisc() when
hitting refcnt 0.
This is very easy to observe with qdisc_reset() tracepoint
and stack traces.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz> Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Wed, 27 May 2020 04:35:26 +0000 (21:35 -0700)]
net_sched: avoid resetting active qdisc for multiple times
Except for sch_mq and sch_mqprio, each dev queue points to the
same root qdisc, so when we reset the dev queues with
netdev_for_each_tx_queue() we end up resetting the same instance
of the root qdisc for multiple times.
Avoid this by checking the __QDISC_STATE_DEACTIVATED bit in
each iteration, so for sch_mq/sch_mqprio, we still reset all
of them like before, for the rest, we only reset it once.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz> Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Wed, 27 May 2020 04:35:23 +0000 (21:35 -0700)]
net_sched: use qdisc_reset() in qdisc_destroy()
qdisc_destroy() calls ops->reset() and cleans up qdisc->gso_skb
and qdisc->skb_bad_txq, these are nearly same with qdisc_reset(),
so just call it directly, and cosolidate the code for the next
patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2020 21:57:27 +0000 (14:57 -0700)]
Merge branch 'tcp-tcp_v4_err-cleanups'
Eric Dumazet says:
====================
tcp: tcp_v4_err() cleanups
This series is a followup of patch 5fc8c26e2270 ("tcp: tcp_v4_err() icmp
skb is named icmp_skb").
Move the RFC 6069 code into a helper, and rename icmp_skb to standard
skb name so that tcp_v4_err() and tcp_v6_err() are using consistent names.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 27 May 2020 02:48:49 +0000 (19:48 -0700)]
tcp: add tcp_ld_RTO_revert() helper
RFC 6069 logic has been implemented for IPv4 only so far,
right in the middle of tcp_v4_err() and was error prone.
Move this code to one helper, to make tcp_v4_err() more
readable and to eventually expand RFC 6069 to IPv6 in
the future.
Also perform sock_owned_by_user() check a bit sooner.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 27 May 2020 00:59:16 +0000 (08:59 +0800)]
net: hns3: remove unnecessary MAC enable in app loopback
Packets will not pass through MAC during app loopback.
Therefore, it is meaningless to enable MAC while doing
app loopback. This patch removes this unnecessary action.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 27 May 2020 00:59:15 +0000 (08:59 +0800)]
net: hns3: change the order of reinitializing RoCE and NIC client during reset
The HNS RDMA driver will support VF device later, whose
re-initialization should be done after PF's. This patch
changes the order of hclge_reset_prepare_up() and
hclge_notify_roce_client(), so that PF's RoCE client
will be reinitialized before VF's.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Wed, 27 May 2020 00:59:14 +0000 (08:59 +0800)]
net: hns3: add a resetting check in hclgevf_init_nic_client_instance()
To prevent from initializing VF NIC client in reset handling state,
this patch adds resetting check in hclgevf_init_nic_client_instance().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: mscc: allow forwarding ioctl operations to attached PHYs
These two patches allow forwarding ioctl to the PHY MII implementation,
and support is added for offloading timestamping operations to
compatible attached PHYs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 26 May 2020 15:01:49 +0000 (17:01 +0200)]
net: mscc: allow offloading timestamping operations to the PHY
This patch adds support for offloading timestamping operations not only
to the Ocelot switch (as already supported) but to compatible PHYs.
When both the PHY and the Ocelot switch support timestamping operations,
the PHY implementation is chosen as the timestamp will happen closer to
the medium.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 26 May 2020 15:01:48 +0000 (17:01 +0200)]
net: mscc: use the PHY MII ioctl interface when possible
Allow ioctl to be implemented by the PHY, when a PHY is attached to the
Ocelot switch. In case the ioctl is a request to set or get the hardware
timestamp, use the Ocelot switch implementation for now.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 27 May 2020 16:45:38 +0000 (19:45 +0300)]
net: dsa: felix: accept VLAN config regardless of bridge VLAN awareness state
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The tests create 100 x32 ecmp groups of ipv4 and ipv6 and then
dump them. On kernels without the fix, they will fail due
to data remnant during the dump.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 27 May 2020 13:34:45 +0000 (15:34 +0200)]
mtk-star-emac: mark PM functions as __maybe_unused
Without CONFIG_PM, the compiler warns about two unused functions:
drivers/net/ethernet/mediatek/mtk_star_emac.c:1472:12: error: unused function 'mtk_star_suspend' [-Werror,-Wunused-function]
drivers/net/ethernet/mediatek/mtk_star_emac.c:1488:12: error: unused function 'mtk_star_resume' [-Werror,-Wunused-function]
Mark these as __maybe_unused.
Fixes: 8c62308a9f55 ("net: ethernet: mtk-star-emac: new driver") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Wed, 27 May 2020 12:34:30 +0000 (12:34 +0000)]
bridge: mrp: Rework the MRP netlink interface
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 27 May 2020 12:01:29 +0000 (13:01 +0100)]
net: dsa: b53: remove redundant premature assignment to new_pvid
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: mtk-star-emac: fix error path in RX handling
The dma_addr field in desc_data must not be overwritten until after the
new skb is mapped. Currently we do replace it with uninitialized value
in error path. This change fixes it by moving the assignment before the
label to which we jump after mapping or allocation errors.
Fixes: 8c62308a9f55 ("net: ethernet: mtk-star-emac: new driver") Reported-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 27 May 2020 08:15:55 +0000 (09:15 +0100)]
mlxsw: spectrum_router: remove redundant initialization of pointer br_dev
The pointer br_dev is being initialized with a value that is never read
and is being updated with a new value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nexthop: Fix type of event_type in call_nexthop_notifiers
Clang warns:
net/ipv4/nexthop.c:841:30: warning: implicit conversion from enumeration
type 'enum nexthop_event_type' to different enumeration type 'enum
fib_event_type' [-Wenum-conversion]
call_nexthop_notifiers(net, NEXTHOP_EVENT_DEL, nh);
~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~
1 warning generated.
Use the right type for event_type so that clang does not warn.
Fixes: 9be0a781d886 ("nexthop: add support for notifiers") Link: https://github.com/ClangBuiltLinux/linux/issues/1038 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Wed, 27 May 2020 05:08:43 +0000 (07:08 +0200)]
net: phy: at803x: add cable diagnostics support for ATH9331 and ATH8032
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 May 2020 06:22:28 +0000 (23:22 -0700)]
Merge branch 'Raw-PHY-TDR-data'
Andrew Lunn says:
====================
Raw PHY TDR data
Some ethernet PHYs allow access to raw TDR data in addition to summary
diagnostics information. Add support for retrieving this data via
netlink ethtool. The basic structure in the core is the same as for
normal phy diagnostics, the PHY driver simply uses different helpers
to fill the netlink message with different data.
There is a graphical tool under development, as well a ethtool(1)
which can dump the data as text and JSON.
A patched ethtool(1) can be found in
https://github.com/lunn/ethtool.git feature/cable-test-v5
Thanks for Chris Healy for lots of testing.
v2:
See the individual patches but:
Pass distances in centimeters, not meters
Allow the PHY to round distances to what it supports and report what
it actually used along with the results.
Make the Marvell PHY use steps a multiple of 0.805 meters, its native
step size.
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Unsquash the last two patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:43 +0000 (00:21 +0200)]
net: phy: marvell: Configure TDR pulse based on measurement length
When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:42 +0000 (00:21 +0200)]
net : phy: marvell: Speedup TDR data retrieval by only changing page once
Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:41 +0000 (00:21 +0200)]
net: ethtool: Allow PHY cable test TDR data to configured
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:40 +0000 (00:21 +0200)]
net: phy: marvell: Add support for amplitude graph
The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:38 +0000 (00:21 +0200)]
net: ethtool: Add generic parts of cable test TDR
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 26 May 2020 22:21:37 +0000 (00:21 +0200)]
net: ethtool: Add attributes for cable test TDR data
Some Ethernet PHYs can return the raw time domain reflectromatry data.
Add the attributes to allow this data to be requested and returned via
netlink ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
m -> cm
Report what the PHY actually used for start/stop/step.
Signed-off-by: David S. Miller <davem@davemloft.net>
Armin Wolf [Tue, 26 May 2020 18:03:02 +0000 (20:03 +0200)]
ne2k-pci: Fix various coding-style issues and improve printk() usage
Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Ignore loopback-originatig packets soon enough and don't try to process L2
header where it doesn't exist. The very similar br_handle_frame() in bridge
code performs exactly the same check.
David S. Miller [Wed, 27 May 2020 03:33:59 +0000 (20:33 -0700)]
Merge branch 'mlxsw-Various-trap-changes-part-2'
Ido Schimmel says:
====================
mlxsw: Various trap changes - part 2
This patch set contains another set of small changes in mlxsw trap
configuration. It is the last set before exposing control traps (e.g.,
IGMP query, ARP request) via devlink-trap.
Tested with existing devlink-trap selftests. Please see individual
patches for a detailed changelog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.
However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.
To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:55 +0000 (02:05 +0300)]
mlxsw: spectrum: Add packet traps for BFD packets
Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).
This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.
Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:54 +0000 (02:05 +0300)]
mlxsw: spectrum: Treat IPv6 link-local SIP as an exception
IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.
As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:53 +0000 (02:05 +0300)]
mlxsw: spectrum: Share one group for all locally delivered packets
Routed IP packets with the Router Alert option need to be trapped to
the CPU as they might need to be locally delivered to raw sockets with
the IP_ROUTER_ALERT / IPV6_ROUTER_ALERT socket option.
Move them to the same group with other packets that might need to be
trapped following route lookup.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:51 +0000 (02:05 +0300)]
mlxsw: spectrum_trap: Do not hard code "thin" policer identifier
As explained in commit 2148dd33563e ("mlxsw: spectrum_trap: Introduce
dummy group with thin policer"), the purpose of the "thin" policer is to
pass as less packets as possible to the CPU.
The identifier of this policer is currently set according to the maximum
number of used trap groups, but this is fragile: On Spectrum-1 the
maximum number of policers is less than the maximum number of trap
groups, which might result in an invalid policer identifier in case the
number of used trap groups grows beyond the policer limit.
Solve this by dynamically allocating the policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:50 +0000 (02:05 +0300)]
mlxsw: switchx2: Move SwitchX-2 trap groups out of main enum
The number of Spectrum trap groups is not infinite, but two identifiers
are occupied by SwitchX-2 specific trap groups. Free these identifiers
by moving them out of the main enum.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:48 +0000 (02:05 +0300)]
mlxsw: spectrum: Use same trap group for local routes and link-local destination
Packets with an IPv6 link-local destination (i.e., fe80::/10) should not
be forwarded and are therefore trapped to the CPU for local delivery.
Since these packets are trapped for the same logical reason as packets
hitting local routes, associate both traps with the same group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:47 +0000 (02:05 +0300)]
mlxsw: spectrum: Use separate trap group for FID miss
When a packet enters the device it is classified to a filtering
identifier (FID) based on the ingress port and VLAN. The FID miss trap
is used to trap packets for which a FID could not be found.
In mlxsw this trap should only be triggered when a port is enslaved to
an OVS bridge and a matching ACL rule could not be found, so as to
trigger learning.
These packets are therefore completely unrelated to packets hitting
local routes and should be in a different group. Move them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 25 May 2020 23:05:45 +0000 (02:05 +0300)]
mlxsw: spectrum: Rename IPv6 ND trap group
The IPv6 Neighbour Discovery (ND) group will be used for various IPv6
packets, not all of which fall under the definition of ND, so rename it
to "IPV6" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log