Lu Baolu [Sat, 25 Jun 2022 13:34:30 +0000 (21:34 +0800)]
iommu/vt-d: Fix RID2PASID setup/teardown failure
The IOMMU driver shares the pasid table for PCI alias devices. When the
RID2PASID entry of the shared pasid table has been filled by the first
device, the subsequent device will encounter the "DMAR: Setup RID2PASID
failed" failure as the pasid entry has already been marked as present.
As the result, the IOMMU probing process will be aborted.
On the contrary, when any alias device is hot-removed from the system,
for example, by writing to /sys/bus/pci/devices/.../remove, the shared
RID2PASID will be cleared without any notifications to other devices.
As the result, any DMAs from those rest devices are blocked.
Sharing pasid table among PCI alias devices could save two memory pages
for devices underneath the PCIe-to-PCI bridges. Anyway, considering that
those devices are rare on modern platforms that support VT-d in scalable
mode and the saved memory is negligible, it's reasonable to remove this
part of immature code to make the driver feasible and stable.
Yian Chen [Sat, 21 May 2022 00:21:15 +0000 (17:21 -0700)]
iommu/vt-d: Fix PCI bus rescan device hot add
Notifier calling chain uses priority to determine the execution
order of the notifiers or listeners registered to the chain.
PCI bus device hot add utilizes the notification mechanism.
The current code sets low priority (INT_MIN) to Intel
dmar_pci_bus_notifier and postpones DMAR decoding after adding
new device into IOMMU. The result is that struct device pointer
cannot be found in DRHD search for the new device's DMAR/IOMMU.
Subsequently, the device is put under the "catch-all" IOMMU
instead of the correct one. This could cause system hang when
device TLB invalidation is sent to the wrong IOMMU. Invalidation
timeout error and hard lockup have been observed and data
inconsistency/crush may occur as well.
This patch fixes the issue by setting a positive priority(1) for
dmar_pci_bus_notifier while the priority of IOMMU bus notifier
uses the default value(0), therefore DMAR decoding will be in
advance of DRHD search for a new device to find the correct IOMMU.
Following is a 2-step example that triggers the bug by simulating
PCI device hot add behavior in Intel Sapphire Rapids server.
lockref: remove unused 'lockref_get_or_lock()' function
Looking at the conditional lock acquire functions in the kernel due to
the new sparse support (see commit 1dbfe72806e7 "sparse: introduce
conditional lock acquire function attribute"), it became obvious that
the lockref code has a couple of them, but they don't match the usual
naming convention for the other ones, and their return value logic is
also reversed.
In the other very similar places, the naming pattern is '*_and_lock()'
(eg 'atomic_put_and_lock()' and 'refcount_dec_and_lock()'), and the
function returns true when the lock is taken.
The lockref code is superficially very similar to the refcount code,
only with the special "atomic wrt the embedded lock" semantics. But
instead of the '*_and_lock()' naming it uses '*_or_lock()'.
And instead of returning true in case it took the lock, it returns true
if it *didn't* take the lock.
Now, arguably the reflock code is quite logical: it really is a "either
decrement _or_ lock" kind of situation - and the return value is about
whether the operation succeeded without any special care needed.
So despite the similarities, the differences do make some sense, and
maybe it's not worth trying to unify the different conditional locking
primitives in this area.
But while looking at this all, it did become obvious that the
'lockref_get_or_lock()' function hasn't actually had any users for
almost a decade.
The only user it ever had was the shortlived 'd_rcu_to_refcount()'
function, and it got removed and replaced with 'lockref_get_not_dead()'
back in 2013 in commits 93fcf83333a8 ("vfs: use lockred 'dead' flag to
mark unrecoverably dead dentries") and 9dfb7f7373c2 ("vfs: fix dentry
RCU to refcounting possibly sleeping dput()")
In fact, that single use was removed less than a week after the whole
function was introduced in commit 3ca2b7185b68 ("lockref: add
'lockref_get_or_lock() helper") so this function has been around for a
decade, but only had a user for six days.
Let's just put this mis-designed and unused function out of its misery.
We can think about the naming and semantic oddities of the remaining
'lockref_put_or_lock()' later, but at least that function has users.
And while the naming is different and the return value doesn't match,
that function matches the whole '{atomic,refcount}_dec_and_test()'
pattern much better (ie the magic happens when the count goes down to
zero, not when it is incremented from zero).
Linus Torvalds [Thu, 30 Jun 2022 16:34:10 +0000 (09:34 -0700)]
sparse: introduce conditional lock acquire function attribute
The kernel tends to try to avoid conditional locking semantics because
it makes it harder to think about and statically check locking rules,
but we do have a few fundamental locking primitives that take locks
conditionally - most obviously the 'trylock' functions.
That has always been a problem for 'sparse' checking for locking
imbalance, and we've had a special '__cond_lock()' macro that we've used
to let sparse know how the locking works:
so that you can then use this to tell sparse that (for example) the
spinlock trylock macro ends up acquiring the lock when it succeeds, but
not when it fails:
and then sparse can follow along the locking rules when you have code like
if (!spin_trylock(&dentry->d_lock))
return LRU_SKIP;
.. sparse sees that the lock is held here..
spin_unlock(&dentry->d_lock);
and sparse ends up happy about the lock contexts.
However, this '__cond_lock()' use does result in very ugly header files,
and requires you to basically wrap the real function with that macro
that uses '__cond_lock'. Which has made PeterZ NAK things that try to
fix sparse warnings over the years [1].
To solve this, there is now a very experimental patch to sparse that
basically does the exact same thing as '__cond_lock()' did, but using a
function attribute instead. That seems to make PeterZ happy [2].
Note that this does not replace existing use of '__cond_lock()', but
only exposes the new proposed attribute and uses it for the previously
unannotated 'refcount_dec_and_lock()' family of functions.
For existing sparse installations, this will make no difference (a
negative output context was ignored), but if you have the experimental
sparse patch it will make sparse now understand code that uses those
functions, the same way '__cond_lock()' makes sparse understand the very
similar 'atomic_dec_and_lock()' uses that have the old '__cond_lock()'
annotations.
Note that in some cases this will silence existing context imbalance
warnings. But in other cases it may end up exposing new sparse warnings
for code that sparse just didn't see the locking for at all before.
This is a trial, in other words. I'd expect that if it ends up being
successful, and new sparse releases end up having this new attribute,
we'll migrate the old-style '__cond_lock()' users to use the new-style
'__cond_acquires' function attribute.
The actual experimental sparse patch was posted in [3].
Merge tag 'xfs-5.19-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"This fixes some stalling problems and corrects the last of the
problems (I hope) observed during testing of the new atomic xattr
update feature.
- Fix statfs blocking on background inode gc workers
- Fix some broken inode lock assertion code
- Fix xattr leaf buffer leaks when cancelling a deferred xattr update
operation
- Clean up xattr recovery to make it easier to understand.
- Fix xattr leaf block verifiers tripping over empty blocks.
- Fix a bug where an rt extent crossing EOF was treated as "posteof"
blocks and cleaned unnecessarily.
- Fix a UAF when log shutdown races with unmount"
* tag 'xfs-5.19-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: prevent a UAF when log IO errors race with unmount
xfs: dont treat rt extents beyond EOF as eofblocks to be cleared
xfs: don't hold xattr leaf buffers across transaction rolls
xfs: empty xattr leaf header blocks are not corruption
xfs: clean up the end of xfs_attri_item_recover
xfs: always free xattri_leaf_bp when cancelling a deferred op
xfs: use invalidate_lock to check the state of mmap_lock
xfs: factor out the common lock flags assert
xfs: introduce xfs_inodegc_push()
xfs: bound maximum wait time for inodegc work
Merge tag 'for-5.19/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"Two important fixes for bugs in code which was added in 5.18:
- Fix userspace signal failures on 32-bit kernel due to a bug in vDSO
- Fix 32-bit load-word unalignment exception handler which returned
wrong values"
* tag 'for-5.19/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix vDSO signal breakage on 32-bit kernel
parisc/unaligned: Fix emulate_ldw() breakage
Addition of vDSO support for parisc in kernel v5.18 suddenly broke glibc
signal testcases on a 32-bit kernel.
The trampoline code (sigtramp.S) which is mapped into userspace includes
an offset to the context data on the stack, which is used by gdb and
glibc to get access to registers.
In a 32-bit kernel we used by mistake the offset into the compat context
(which is valid on a 64-bit kernel only) instead of the offset into the
"native" 32-bit context.
Reported-by: John David Anglin <dave.anglin@bell.net> Tested-by: John David Anglin <dave.anglin@bell.net> Fixes: bf25c2f6432b ("parisc: Add vDSO support") CC: stable@vger.kernel.org # 5.18 Signed-off-by: Helge Deller <deller@gmx.de>
Merge tag 'perf-tools-fixes-for-v5.19-2022-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- BPF program info linear (BPIL) data is accessed assuming 64-bit
alignment resulting in undefined behavior as the data is just byte
aligned. Fix it, Found using -fsanitize=undefined.
- Fix 'perf offcpu' build on old kernels wrt task_struct's
state/__state field.
- Fix perf_event_attr.sample_type setting on the 'offcpu-time' event
synthesized by the 'perf offcpu' tool.
- Don't bail out when synthesizing PERF_RECORD_ events for pre-existing
threads when one goes away while parsing its procfs entries.
- Don't sort the task scan result from /proc, its not needed and
introduces bugs when the main thread isn't the first one to be
processed.
- Fix uninitialized 'offset' variable on aarch64 in the unwind code.
- Sync KVM headers with the kernel sources.
* tag 'perf-tools-fixes-for-v5.19-2022-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf synthetic-events: Ignore dead threads during event synthesis
perf synthetic-events: Don't sort the task scan result from /proc
perf unwind: Fix unitialized 'offset' variable on aarch64
tools headers UAPI: Sync linux/kvm.h with the kernel sources
perf bpf: 8 byte align bpil data
tools kvm headers arm64: Update KVM headers from the kernel sources
perf offcpu: Accept allowed sample types only
perf offcpu: Fix build failure on old kernels
Merge tag 'powerpc-5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix BPF uapi confusion about the correct type of bpf_user_pt_regs_t.
- Fix virt_addr_valid() when memory is hotplugged above the boot-time
high_memory value.
- Fix a bug in 64-bit Book3E map_kernel_page() which would incorrectly
allocate a PMD page at PUD level.
- Fix a couple of minor issues found since we enabled KASAN for 64-bit
Book3S.
Thanks to Aneesh Kumar K.V, Cédric Le Goater, Christophe Leroy, Kefeng
Wang, Liam Howlett, Nathan Lynch, and Naveen N. Rao.
* tag 'powerpc-5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/memhotplug: Add add_pages override for PPC
powerpc/bpf: Fix use of user_pt_regs in uapi
powerpc/prom_init: Fix kernel config grep
powerpc/book3e: Fix PUD allocation size in map_kernel_page()
powerpc/xive/spapr: correct bitmap allocation size
Namhyung Kim [Fri, 1 Jul 2022 20:54:58 +0000 (13:54 -0700)]
perf synthetic-events: Ignore dead threads during event synthesis
When it synthesize various task events, it scans the list of task
first and then accesses later. There's a window threads can die
between the two and proc entries may not be available.
Instead of bailing out, we can ignore that thread and move on.
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220701205458.985106-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Fri, 1 Jul 2022 20:54:57 +0000 (13:54 -0700)]
perf synthetic-events: Don't sort the task scan result from /proc
It should not sort the result as procfs already returns a proper
ordering of tasks. Actually sorting the order caused problems that it
doesn't guararantee to process the main thread first.
Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220701205458.985106-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ivan Babrou [Fri, 1 Jul 2022 18:20:46 +0000 (11:20 -0700)]
perf unwind: Fix unitialized 'offset' variable on aarch64
Commit f68f6c7d442bb94a ("perf unwind: Fix segbase for ld.lld linked
objects") uncovered the following issue on aarch64:
util/unwind-libunwind-local.c: In function 'find_proc_info':
util/unwind-libunwind-local.c:386:28: error: 'offset' may be used uninitialized in this function [-Werror=maybe-uninitialized]
386 | if (ofs > 0) {
| ^
util/unwind-libunwind-local.c:199:22: note: 'offset' was declared here
199 | u64 address, offset;
| ^~~~~~
util/unwind-libunwind-local.c:371:20: error: 'offset' may be used uninitialized in this function [-Werror=maybe-uninitialized]
371 | if (ofs <= 0) {
| ^
util/unwind-libunwind-local.c:199:22: note: 'offset' was declared here
199 | u64 address, offset;
| ^~~~~~
util/unwind-libunwind-local.c:363:20: error: 'offset' may be used uninitialized in this function [-Werror=maybe-uninitialized]
363 | if (ofs <= 0) {
| ^
util/unwind-libunwind-local.c:199:22: note: 'offset' was declared here
199 | u64 address, offset;
| ^~~~~~
In file included from util/libunwind/arm64.c:37:
Fixes: f68f6c7d442bb94a ("perf unwind: Fix segbase for ld.lld linked objects") Signed-off-by: Ivan Babrou <ivan@cloudflare.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Fangrui Song <maskray@google.com> Cc: Ian Rogers <irogers@google.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: kernel-team@cloudflare.com Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220701182046.12589-1-ivan@cloudflare.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge tag 'libnvdimm-fixes-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Vishal Verma:
- Fix a bug in the libnvdimm 'BTT' (Block Translation Table) driver
where accounting for poison blocks to be cleared was off by one,
causing a failure to clear the the last badblock in an nvdimm region.
* tag 'libnvdimm-fixes-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm: Fix badblocks clear off-by-one error
Merge tag 'thermal-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Add a new CPU ID to the list of supported processors in the
intel_tcc_cooling driver (Sumeet Pawnikar)"
* tag 'thermal-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel_tcc_cooling: Add TCC cooling support for RaptorLake
Merge tag 'pm-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix some issues in cpufreq drivers and some issues in devfreq:
- Fix error code path issues related PROBE_DEFER handling in devfreq
(Christian Marangi)
- Revert an editing accident in SPDX-License line in the devfreq
passive governor (Lukas Bulwahn)
- Fix refcount leak in of_get_devfreq_events() in the exynos-ppmu
devfreq driver (Miaoqian Lin)
- Use HZ_PER_KHZ macro in the passive devfreq governor (Yicong Yang)
- Fix missing of_node_put for qoriq and pmac32 driver (Liang He)
- Fix issues around throttle interrupt for qcom driver (Stephen Boyd)
- Add MT8186 to cpufreq-dt-platdev blocklist (AngeloGioacchino Del
Regno)
- Make amd-pstate enable CPPC on resume from S3 (Jinzhou Su)"
* tag 'pm-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: passive: revert an editing accident in SPDX-License line
PM / devfreq: Fix kernel warning with cpufreq passive register fail
PM / devfreq: Rework freq_table to be local to devfreq struct
PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
PM / devfreq: passive: Use HZ_PER_KHZ macro in units.h
PM / devfreq: Fix cpufreq passive unregister erroring on PROBE_DEFER
PM / devfreq: Mute warning on governor PROBE_DEFER
PM / devfreq: Fix kernel panic with cpu based scaling to passive gov
cpufreq: Add MT8186 to cpufreq-dt-platdev blocklist
cpufreq: pmac32-cpufreq: Fix refcount leak bug
cpufreq: qcom-hw: Don't do lmh things without a throttle interrupt
drivers: cpufreq: Add missing of_node_put() in qoriq-cpufreq.c
cpufreq: amd-pstate: Add resume and suspend callbacks
Merge tag 'hwmon-for-v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix error handling in ibmaem driver initialization
- Fix bad data reported by occ driver after setting power cap
- Fix typos in pmbus/ucd9200 driver comments
* tag 'hwmon-for-v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ibmaem) don't call platform_device_del() if platform_device_add() fails
hwmon: (pmbus/ucd9200) fix typos in comments
hwmon: (occ) Prevent power cap command overwriting poll response
Yang Yingliang [Fri, 1 Jul 2022 07:41:53 +0000 (15:41 +0800)]
hwmon: (ibmaem) don't call platform_device_del() if platform_device_add() fails
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes: 5c0abd28a4fe ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge tag 's390-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Fix purgatory build process so bin2c tool does not get built
unnecessarily and the Makefile is more consistent with other
architectures.
- Return earlier simple design of arch_get_random_seed_long|int() and
arch_get_random_long|int() callbacks as result of changes in generic
RNG code.
- Fix minor comment typos and spelling mistakes.
* tag 's390-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/qdio: Fix spelling mistake
s390/sclp: Fix typo in comments
s390/archrandom: simplify back to earlier design and initialize earlier
s390/purgatory: remove duplicated build rule of kexec-purgatory.o
s390/purgatory: hard-code obj-y in Makefile
s390: remove unneeded 'select BUILD_BIN2C'
Merge tag 'nfs-for-5.19-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
- Allocate a fattr for _nfs4_discover_trunking()
- Fix module reference count leak in nfs4_run_state_manager()
* tag 'nfs-for-5.19-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
NFSv4: Add an fattr allocation to _nfs4_discover_trunking()
NFS: restore module put when manager exits.
Merge tag 'for-5.19/dm-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Three fixes for invalid memory accesses discovered by using KASAN
while running the lvm2 testsuite's dm-raid tests. Includes changes to
MD's raid5.c given the dependency dm-raid has on the MD code"
* tag 'for-5.19/dm-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix KASAN warning in raid5_add_disks
dm raid: fix KASAN warning in raid5_remove_disk
dm raid: fix accesses beyond end of raid member array
Merge tag 'io_uring-5.19-2022-07-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two minor tweaks:
- While we still can, adjust the send/recv based flags to be in
->ioprio rather than in ->addr2. This is consistent with eg accept,
and also doesn't waste a full 64-bit field for flags (Pavel)
- 5.18-stable fix for re-importing provided buffers. Not much real
world relevance here as it'll only impact non-pollable files gone
async, which is more of a practical test case rather than something
that is used in the wild (Dylan)"
* tag 'io_uring-5.19-2022-07-01' of git://git.kernel.dk/linux-block:
io_uring: fix provided buffer import
io_uring: keep sendrecv flags in ioprio
Merge tag 'block-5.19-2022-07-01' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Fix for batch getting of tags in sbitmap (wuchi)
- NVMe pull request via Christoph:
- More quirks (Lamarque Vieira Souza, Pablo Greco)
- Fix a fabrics disconnect regression (Ruozhu Li)
- Fix a nvmet-tcp data_digest calculation regression (Sagi
Grimberg)
- Fix nvme-tcp send failure handling (Sagi Grimberg)
- Fix a regression with nvmet-loop and passthrough controllers
(Alan Adamson)
* tag 'block-5.19-2022-07-01' of git://git.kernel.dk/linux-block:
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
nvmet: add a clear_ids attribute for passthru targets
nvme: fix regression when disconnect a recovering ctrl
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX S40G)
nvme-tcp: always fail a request when sending it failed
nvmet-tcp: fix regression in data_digest calculation
lib/sbitmap: Fix invalid loop in __sbitmap_queue_get_batch()
Will Deacon [Wed, 29 Jun 2022 09:53:49 +0000 (10:53 +0100)]
arm64: hugetlb: Restore TLB invalidation for BBM on contiguous ptes
Commit 42dbb8dc8f17 ("arm64/hugetlb: Drop TLB flush from get_clear_flush()")
removed TLB invalidation from get_clear_flush() [now get_clear_contig()]
on the basis that the core TLB invalidation code is aware of hugetlb
mappings backed by contiguous page-table entries and will cover the
correct virtual address range.
However, this change also resulted in the TLB invalidation being removed
from the "break" step in the break-before-make (BBM) sequence used
internally by huge_ptep_set_{access_flags,wrprotect}(), therefore
making the BBM sequence unsafe irrespective of later invalidation.
Although the architecture is desperately unclear about how exactly
contiguous ptes should be updated in a live page-table, restore TLB
invalidation to our BBM sequence under the assumption that BBM is the
right thing to be doing in the first place.
Fixes: 42dbb8dc8f17 ("arm64/hugetlb: Drop TLB flush from get_clear_flush()") Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Steve Capper <steve.capper@arm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20220629095349.25748-1-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two small fixes
- Initialize a spinlock in the stm32 reset code
- Add dt bindings to the clk maintainer filepattern"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
MAINTAINERS: add include/dt-bindings/clock to COMMON CLK FRAMEWORK
clk: stm32: rcc_reset: Fix missing spin_lock_init()
This appears to be a race between the unmount process, which frees the
CIL and waits for in-flight iclog IO; and the iclog IO completion. When
generic/475 runs, it starts fsstress in the background, waits a few
seconds, and substitutes a dm-error device to simulate a disk falling
out of a machine. If the fsstress encounters EIO on a pure data write,
it will exit but the filesystem will still be online.
The next thing the test does is unmount the filesystem, which tries to
clean the log, free the CIL, and wait for iclog IO completion. If an
iclog was being written when the dm-error switch occurred, it can race
with log unmounting as follows:
Thread 1 Thread 2
xfs_log_unmount
xfs_log_clean
xfs_log_quiesce
xlog_ioend_work
<observe error>
xlog_force_shutdown
test_and_set_bit(XLOG_IOERROR)
xfs_log_force
<log is shut down, nop>
xfs_log_umount_write
<log is shut down, nop>
xlog_dealloc_log
xlog_cil_destroy
<wait for iclogs>
spin_lock(&log->l_cilp->xc_push_lock)
<KABOOM>
Therefore, free the CIL after waiting for the iclogs to complete. I
/think/ this race has existed for quite a few years now, though I don't
remember the ~2014 era logging code well enough to know if it was a real
threat then or if the actual race was exposed only more recently.
Fixes: 32b99274275b ("xfs: don't sleep in xlog_cil_force_lsn on shutdown") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com>
Merge tag 'drm-fixes-2022-07-01' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Bit quieter this week, the main thing is it pulls in the fixes for the
sysfb resource issue you were seeing. these had been queued for next
so should have had some decent testing.
Otherwise amdgpu, i915 and msm each have a few fixes, and vc4 has one.
fbdev:
- sysfb fixes/conflicting fb fixes
amdgpu:
- GPU recovery fix
- Fix integer type usage in fourcc header for AMD modifiers
- Fix setting cache_dirty for dma-buf objects on discrete
msm:
- Fix to increment vsync_cnt before calling drm_crtc_handle_vblank so
that userspace sees the value *after* it is incremented if waiting
for vblank events
- Fix to reset drm_dev to NULL in dp_display_unbind to avoid a crash
in probe/bind error paths
- Fix to resolve the smatch error of de-referencing before NULL check
in dpu_encoder_phys_wb.c
- Fix error return to userspace if fence-id allocation fails in
submit ioctl
vc4:
- NULL ptr dereference fix"
* tag 'drm-fixes-2022-07-01' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/amdgpu/display: set vblank_disable_immediate for DC"
drm/amdgpu: To flush tlb for MMHUB of RAVEN series
drm/fourcc: fix integer type usage in uapi header
drm/amdgpu: fix adev variable used in amdgpu_device_gpu_recover()
fbdev: Disable sysfb device registration when removing conflicting FBs
firmware: sysfb: Add sysfb_disable() helper function
firmware: sysfb: Make sysfb_create_simplefb() return a pdev pointer
drm/msm/gem: Fix error return on fence id alloc fail
drm/i915: tweak the ordering in cpu_write_needs_clflush
drm/i915/dgfx: Disable d3cold at gfx root port
drm/i915/gem: add missing else
drm/vc4: perfmon: Fix variable dereferenced before check
drm/msm/dpu: Fix variable dereferenced before check
drm/msm/dp: reset drm_dev to NULL at dp_display_unbind()
drm/msm/dpu: Increment vsync_cnt before waking up userspace
Amir Goldstein [Thu, 30 Jun 2022 19:58:49 +0000 (22:58 +0300)]
vfs: fix copy_file_range() regression in cross-fs copies
A regression has been reported by Nicolas Boichat, found while using the
copy_file_range syscall to copy a tracefs file.
Before commit 6c5c6aabe260 ("vfs: allow copy_file_range to copy across
devices") the kernel would return -EXDEV to userspace when trying to
copy a file across different filesystems. After this commit, the
syscall doesn't fail anymore and instead returns zero (zero bytes
copied), as this file's content is generated on-the-fly and thus reports
a size of zero.
Another regression has been reported by He Zhe - the assertion of
WARN_ON_ONCE(ret == -EOPNOTSUPP) can be triggered from userspace when
copying from a sysfs file whose read operation may return -EOPNOTSUPP.
Since we do not have test coverage for copy_file_range() between any two
types of filesystems, the best way to avoid these sort of issues in the
future is for the kernel to be more picky about filesystems that are
allowed to do copy_file_range().
This patch restores some cross-filesystem copy restrictions that existed
prior to commit 6c5c6aabe260 ("vfs: allow copy_file_range to copy across
devices"), namely, cross-sb copy is not allowed for filesystems that do
not implement ->copy_file_range().
Filesystems that do implement ->copy_file_range() have full control of
the result - if this method returns an error, the error is returned to
the user. Before this change this was only true for fs that did not
implement the ->remap_file_range() operation (i.e. nfsv3).
Filesystems that do not implement ->copy_file_range() still fall-back to
the generic_copy_file_range() implementation when the copy is within the
same sb. This helps the kernel can maintain a more consistent story
about which filesystems support copy_file_range().
nfsd and ksmbd servers are modified to fall-back to the
generic_copy_file_range() implementation in case vfs_copy_file_range()
fails with -EOPNOTSUPP or -EXDEV, which preserves behavior of
server-side-copy.
fall-back to generic_copy_file_range() is not implemented for the smb
operation FSCTL_DUPLICATE_EXTENTS_TO_FILE, which is arguably a correct
change of behavior.
Chuck Lever [Thu, 30 Jun 2022 20:48:18 +0000 (16:48 -0400)]
SUNRPC: Fix READ_PLUS crasher
Looks like there are still cases when "space_left - frag1bytes" can
legitimately exceed PAGE_SIZE. Ensure that xdr->end always remains
within the current encode buffer.
Reported-by: Bruce Fields <bfields@fieldses.org> Reported-by: Zorro Lang <zlang@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216151 Fixes: 92e0f6675577 ("SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()") Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Scott Mayhew [Mon, 27 Jun 2022 21:31:29 +0000 (17:31 -0400)]
NFSv4: Add an fattr allocation to _nfs4_discover_trunking()
This was missed in 254a37718b3f ("NFSv4: Fix free of uninitialized
nfs4_label on referral lookup.") and causes a panic when mounting
with '-o trunkdiscovery':
Fixes: 254a37718b3f ("NFSv4: Fix free of uninitialized nfs4_label on referral lookup.") Signed-off-by: Scott Mayhew <smayhew@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
NeilBrown [Thu, 23 Jun 2022 04:47:34 +0000 (14:47 +1000)]
NFS: restore module put when manager exits.
Commit f0f8648589e6 ("NFSD: Remove svc_serv_ops::svo_module") removed
calls to module_put_and_kthread_exit() from threads that acted as SUNRPC
servers and had a related svc_serv_ops structure. This was correct.
It ALSO removed the module_put_and_kthread_exit() call from
nfs4_run_state_manager() which is NOT a SUNRPC service.
Consequently every time the NFSv4 state manager runs the module count
increments and won't be decremented. So the nfsv4 module cannot be
unloaded.
So restore the module_put_and_kthread_exit() call.
Jens Axboe [Thu, 30 Jun 2022 20:00:11 +0000 (14:00 -0600)]
Merge tag 'nvme-5.19-2022-06-30' of git://git.infradead.org/nvme into block-5.19
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.19
- more quirks (Lamarque Vieira Souza, Pablo Greco)
- fix a fabrics disconnect regression (Ruozhu Li)
- fix a nvmet-tcp data_digest calculation regression (Sagi Grimberg)
- fix nvme-tcp send failure handling (Sagi Grimberg)
- fix a regression with nvmet-loop and passthrough controllers
(Alan Adamson)"
* tag 'nvme-5.19-2022-06-30' of git://git.infradead.org/nvme:
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
nvmet: add a clear_ids attribute for passthru targets
nvme: fix regression when disconnect a recovering ctrl
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX S40G)
nvme-tcp: always fail a request when sending it failed
nvmet-tcp: fix regression in data_digest calculation
Vladimir Oltean [Wed, 29 Jun 2022 18:30:07 +0000 (21:30 +0300)]
net: dsa: felix: fix race between reading PSFP stats and port stats
Both PSFP stats and the port stats read by ocelot_check_stats_work() are
indirectly read through the same mechanism - write to STAT_CFG:STAT_VIEW,
read from SYS:STAT:CNT[n].
It's just that for port stats, we write STAT_VIEW with the index of the
port, and for PSFP stats, we write STAT_VIEW with the filter index.
So if we allow them to run concurrently, ocelot_check_stats_work() may
change the view from vsc9959_psfp_counters_get(), and vice versa.
Jakub Kicinski [Wed, 29 Jun 2022 18:19:10 +0000 (11:19 -0700)]
net: tun: avoid disabling NAPI twice
Eric reports that syzbot made short work out of my speculative
fix. Indeed when queue gets detached its tfile->tun remains,
so we would try to stop NAPI twice with a detach(), close()
sequence.
Alternative fix would be to move tun_napi_disable() to
tun_detach_all() and let the NAPI run after the queue
has been detached.
Fixes: 6760cd5a7546 ("net: tun: stop NAPI when detaching queues") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220629181911.372047-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
s390/archrandom: simplify back to earlier design and initialize earlier
s390x appears to present two RNG interfaces:
- a "TRNG" that gathers entropy using some hardware function; and
- a "DRBG" that takes in a seed and expands it.
Previously, the TRNG was wired up to arch_get_random_{long,int}(), but
it was observed that this was being called really frequently, resulting
in high overhead. So it was changed to be wired up to arch_get_random_
seed_{long,int}(), which was a reasonable decision. Later on, the DRBG
was then wired up to arch_get_random_{long,int}(), with a complicated
buffer filling thread, to control overhead and rate.
Fortunately, none of the performance issues matter much now. The RNG
always attempts to use arch_get_random_seed_{long,int}() first, which
means a complicated implementation of arch_get_random_{long,int}() isn't
really valuable or useful to have around. And it's only used when
reseeding, which means it won't hit the high throughput complications
that were faced before.
So this commit returns to an earlier design of just calling the TRNG in
arch_get_random_seed_{long,int}(), and returning false in arch_get_
random_{long,int}().
Part of what makes the simplification possible is that the RNG now seeds
itself using the TRNG at bootup. But this only works if the TRNG is
detected early in boot, before random_init() is called. So this commit
also causes that check to happen in setup_arch().
Cc: stable@vger.kernel.org Cc: Harald Freudenberger <freude@linux.ibm.com> Cc: Ingo Franzki <ifranzki@linux.ibm.com> Cc: Juergen Christ <jchrist@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Link: https://lore.kernel.org/r/20220610222023.378448-1-Jason@zx2c4.com Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Linus Torvalds [Thu, 30 Jun 2022 17:03:22 +0000 (10:03 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Three minor bug fixes:
- qedr not setting the QP timeout properly toward userspace
- Memory leak on error path in ib_cm
- Divide by 0 in RDMA interrupt moderation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
linux/dim: Fix divide by 0 in RDMA DIM
RDMA/cm: Fix memory leak in ib_cm_insert_listen
RDMA/qedr: Fix reporting QP timeout attribute
Linus Torvalds [Thu, 30 Jun 2022 16:57:18 +0000 (09:57 -0700)]
Merge tag 'fsnotify_for_v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fanotify fix from Jan Kara:
"A fix for recently added fanotify API to have stricter checks and
refuse some invalid flag combinations to make our life easier in the
future"
* tag 'fsnotify_for_v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: refine the validation checks on non-dir inode mask
Linus Torvalds [Thu, 30 Jun 2022 16:45:42 +0000 (09:45 -0700)]
Merge tag 'v5.19-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression that breaks the ccp driver"
* tag 'v5.19-p3' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccp - Fix device IRQ counting by using platform_irq_count()
Merge tag 'devfreq-fixes-for-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq fixes for 5.19-rc5 from Chanwoo Choi:
"1. Fix devfreq passive governor issue when cpufreq policies are not
ready during kernel boot because some CPUs turn on after kernel
booting or others.
- Re-initialize the vairables of struct devfreq_passive_data when
PROBE_DEFER happens when cpufreq_get() returns NULL.
- Use dev_err_probe to mute warning when PROBE_DEFER.
- Fix cpufreq passive unregister erroring on PROBE_DEFER
by using the allocated parent_cpu_data list to free resouce
instead of for_each_possible_cpu().
- Remove duplicate cpufreq passive unregister and warning when
PROBE_DEFER.
- Use HZ_PER_KZH macro in units.h.
- Fix wrong indentation in SPDX-License line.
2. Fix reference count leak in exynos-ppmu.c by using of_node_put().
3. Rework freq_table to be local to devfreq struct
- struct devfreq_dev_profile includes freq_table array to store
the supported frequencies. If devfreq driver doesn't initialize
the freq_table, devfreq core allocates the memory and initializes
the freq_table.
On a devfreq PROBE_DEFER, the freq_table in the driver profile
struct is never reset and may be left in an undefined state. To fix
this and correctly handle PROBE_DEFER, use a local freq_table and
max_state in the devfreq struct."
* tag 'devfreq-fixes-for-5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: passive: revert an editing accident in SPDX-License line
PM / devfreq: Fix kernel warning with cpufreq passive register fail
PM / devfreq: Rework freq_table to be local to devfreq struct
PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
PM / devfreq: passive: Use HZ_PER_KHZ macro in units.h
PM / devfreq: Fix cpufreq passive unregister erroring on PROBE_DEFER
PM / devfreq: Mute warning on governor PROBE_DEFER
PM / devfreq: Fix kernel panic with cpu based scaling to passive gov
Pavel Begunkov [Thu, 30 Jun 2022 12:25:57 +0000 (13:25 +0100)]
io_uring: keep sendrecv flags in ioprio
We waste a u64 SQE field for flags even though we don't need as many
bits and it can be used for something more useful later. Store io_uring
specific send/recv flags in sqe->ioprio instead of ->addr2.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Fixes: 6bb2c14111c3 ("io_uring: add POLL_FIRST support for send/sendmsg and recv/recvmsg")
[axboe: change comment in io_uring.h as well] Signed-off-by: Jens Axboe <axboe@kernel.dk>
Petr Machata [Wed, 29 Jun 2022 07:02:05 +0000 (10:02 +0300)]
mlxsw: spectrum_router: Fix rollback in tunnel next hop init
In mlxsw_sp_nexthop6_init(), a next hop is always added to the router
linked list, and mlxsw_sp_nexthop_type_init() is invoked afterwards. When
that function results in an error, the next hop will not have been removed
from the linked list. As the error is propagated upwards and the caller
frees the next hop object, the linked list ends up holding an invalid
object.
A similar issue comes up with mlxsw_sp_nexthop4_init(), where rollback
block does exist, however does not include the linked list removal.
Both IPv6 and IPv4 next hops have a similar issue with next-hop counter
rollbacks. As these were introduced in the same patchset as the next hop
linked list, include the cleanup in this patch.
Fixes: 4e4a8cbe8a97 ("mlxsw: spectrum_router: Keep nexthops in a linked list") Fixes: 57b8fd70b9c8 ("mlxsw: spectrum: Add support for setting counters on nexthops") Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Amit Cohen <amcohen@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220629070205.803952-1-idosch@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Duoming Zhou [Wed, 29 Jun 2022 00:26:40 +0000 (08:26 +0800)]
net: rose: fix UAF bugs caused by timer handler
There are UAF bugs in rose_heartbeat_expiry(), rose_timer_expiry()
and rose_idletimer_expiry(). The root cause is that del_timer()
could not stop the timer handler that is running and the refcount
of sock is not managed properly.
This patch adds refcount of sock when we use functions
such as rose_start_heartbeat() and so on to start timer,
and decreases the refcount of sock when timer is finished
or deleted by functions such as rose_stop_heartbeat()
and so on. As a result, the UAF bugs could be mitigated.
Jose Alonso [Tue, 28 Jun 2022 15:13:02 +0000 (12:13 -0300)]
net: usb: ax88179_178a: Fix packet receiving
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 49d60052a7fe ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup") Fixes: ce13f848757a ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Signed-off-by: Jose Alonso <joalonsof@gmail.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA IM2P33F8ABR1
ADATA IM2P33F8ABR1 reports bogus eui64 values that appear to be the same
across all drives. Quirk them out so they are not marked as "non globally
unique" duplicates.
Co-developed-by: Felipe de Jesus Araujo da Conceição <felipe.conceicao@petrosoftdesign.com> Signed-off-by: Felipe de Jesus Araujo da Conceição <felipe.conceicao@petrosoftdesign.com> Signed-off-by: Lamarque V. Souza <lamarque.souza@petrosoftdesign.com> Cc: stable@vger.kernel.org Signed-off-by: Christoph Hellwig <hch@lst.de>
Alan Adamson [Mon, 27 Jun 2022 23:25:43 +0000 (16:25 -0700)]
nvmet: add a clear_ids attribute for passthru targets
If the clear_ids attribute is set to true, the EUI/GUID/UUID is cleared
for the passthru target. By default, loop targets will set clear_ids to
true.
This resolves an issue where a connect to a passthru target fails when
using a trtype of 'loop' because EUI/GUID/UUID is not unique.
Fixes: cefdfcdbff7f ("nvme: check that EUI/GUID/UUID are globally unique") Signed-off-by: Alan Adamson <alan.adamson@oracle.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Yevhen Orlov [Wed, 29 Jun 2022 01:29:14 +0000 (04:29 +0300)]
net: bonding: fix use-after-free after 802.3ad slave unbind
commit badbe055b92f ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit badbe055b92f ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
Oleksij Rempel [Tue, 28 Jun 2022 11:43:49 +0000 (13:43 +0200)]
net: phy: ax88772a: fix lost pause advertisement configuration
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes: 877cfd219ba7 ("net: usb/phy: asix: add support for ax88772A/C PHYs") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lukas Wunner [Tue, 28 Jun 2022 10:15:08 +0000 (12:15 +0200)]
net: phy: Don't trigger state machine while in suspend
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 3e5d3f0549b3 ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Oliver Neukum [Tue, 28 Jun 2022 09:35:17 +0000 (11:35 +0200)]
usbnet: fix memory allocation in helpers
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Coleman Dietsch [Tue, 28 Jun 2022 17:47:44 +0000 (12:47 -0500)]
selftests net: fix kselftest net fatal error
The incorrect path is causing the following error when trying to run net
kselftests:
In file included from bpf/nat6to4.c:43:
../../../lib/bpf/bpf_helpers.h:11:10: fatal error: 'bpf_helper_defs.h' file not found
^~~~~~~~~~~~~~~~~~~
1 error generated.
1) Restore set counter when one of the CPU loses race to add elements
to sets.
2) After NF_STOLEN, skb might be there no more, update nftables trace
infra to avoid access to skb in this case. From Florian Westphal.
3) nftables bridge might register a prerouting hook with zero priority,
br_netfilter incorrectly skips it. Also from Florian.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: br_netfilter: do not skip all hooks with 0 priority
netfilter: nf_tables: avoid skb access on nf_stolen
netfilter: nft_dynset: restore set element counter when failing to update
====================
Mikulas Patocka [Wed, 29 Jun 2022 17:40:57 +0000 (13:40 -0400)]
dm raid: fix KASAN warning in raid5_add_disks
There's a KASAN warning in raid5_add_disk when running the LVM testsuite.
The warning happens in the test
lvconvert-raid-reshape-linear_to_raid6-single-type.sh. We fix the warning
by verifying that rdev->saved_raid_disk is within limits.
Cc: stable@vger.kernel.org Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Mikulas Patocka [Wed, 29 Jun 2022 17:40:01 +0000 (13:40 -0400)]
dm raid: fix KASAN warning in raid5_remove_disk
There's a KASAN warning in raid5_remove_disk when running the LVM
testsuite. We fix this warning by verifying that the "number" variable is
within limits.
Cc: stable@vger.kernel.org Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
John Garry [Wed, 29 Jun 2022 09:18:44 +0000 (17:18 +0800)]
ata: pata_cs5535: Fix W=1 warnings
x86_64 allmodconfig build with W=1 gives these warnings:
drivers/ata/pata_cs5535.c: In function ‘cs5535_set_piomode’:
drivers/ata/pata_cs5535.c:93:11: error: variable ‘dummy’ set but not
used [-Werror=unused-but-set-variable]
u32 reg, dummy;
^~~~~
drivers/ata/pata_cs5535.c: In function ‘cs5535_set_dmamode’:
drivers/ata/pata_cs5535.c:132:11: error: variable ‘dummy’ set but not
used [-Werror=unused-but-set-variable]
u32 reg, dummy;
^~~~~
cc1: all warnings being treated as errors
Mark variables 'dummy' as "maybe unused" as they are only ever written
in rdmsr() calls.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Jiang Jian [Wed, 22 Jun 2022 06:32:31 +0000 (14:32 +0800)]
hwmon: (pmbus/ucd9200) fix typos in comments
Drop the redundant word 'the' in the comments following
/*
* Set PHASE registers on all pages to 0xff to ensure that phase
* specific commands will apply to all phases of a given page (rail).
* This only affects the READ_IOUT and READ_TEMPERATURE2 registers.
* READ_IOUT will return the sum of currents of all phases of a rail,
* and READ_TEMPERATURE2 will return the maximum temperature detected
* for the [the - DROP] phases of the rail.
*/
Eddie James [Tue, 28 Jun 2022 20:30:29 +0000 (15:30 -0500)]
hwmon: (occ) Prevent power cap command overwriting poll response
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Lukas Bulwahn [Tue, 28 Jun 2022 05:34:11 +0000 (07:34 +0200)]
PM / devfreq: passive: revert an editing accident in SPDX-License line
Commit 6664dfa189bc ("PM / devfreq: passive: Keep cpufreq_policy for
possible cpus") reworked governor_passive.c, and accidently added a
tab in the first line, i.e., the SPDX-License-Identifier line.
The checkpatch script warns with the SPDX_LICENSE_TAG warning, and hence
pointed this issue out while investigating checkpatch warnings.
Revert this editing accident. No functional change.
Remove cpufreq_passive_unregister_notifier from
cpufreq_passive_register_notifier in case of error as devfreq core
already call unregister on GOV_START fail.
This fix the kernel always printing a WARN on governor PROBE_DEFER as
cpufreq_passive_unregister_notifier is called two times and return
error on the second call as the cpufreq is already unregistered.
Fixes: 0de7288a58b9 ("PM / devfreq: Add cpu based scaling support to passive governor") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
PM / devfreq: Rework freq_table to be local to devfreq struct
On a devfreq PROBE_DEFER, the freq_table in the driver profile struct,
is never reset and may be leaved in an undefined state.
This comes from the fact that we store the freq_table in the driver
profile struct that is commonly defined as static and not reset on
PROBE_DEFER.
We currently skip the reinit of the freq_table if we found
it's already defined since a driver may declare his own freq_table.
This logic is flawed in the case devfreq core generate a freq_table, set
it in the profile struct and then PROBE_DEFER, freeing the freq_table.
In this case devfreq will found a NOT NULL freq_table that has been
freed, skip the freq_table generation and probe the driver based on the
wrong table.
To fix this and correctly handle PROBE_DEFER, use a local freq_table and
max_state in the devfreq struct and never modify the freq_table present
in the profile struct if it does provide it.
Fixes: 8792426c3f11 ("PM / devfreq: Set the freq_table of devfreq device") Cc: stable@vger.kernel.org Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Miaoqian Lin [Thu, 26 May 2022 08:28:56 +0000 (12:28 +0400)]
PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
This function only calls of_node_put() in normal path,
missing it in error paths.
Add missing of_node_put() to avoid refcount leak.
PM / devfreq: Fix cpufreq passive unregister erroring on PROBE_DEFER
With the passive governor, the cpu based scaling can PROBE_DEFER due to
the fact that CPU policy are not ready.
The cpufreq passive unregister notifier is called both from the
GOV_START errors and for the GOV_STOP and assume the notifier is
successfully registred every time. With GOV_START failing it's wrong to
loop over each possible CPU since the register path has failed for
some CPU policy not ready. Change the logic and unregister the notifer
based on the current allocated parent_cpu_data list to correctly handle
errors and the governor unregister path.
Fixes: 0de7288a58b9 ("PM / devfreq: Add cpu based scaling support to passive governor") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
PM / devfreq: Mute warning on governor PROBE_DEFER
Don't print warning when a governor PROBE_DEFER as it's not a real
GOV_START fail.
Fixes: 0de7288a58b9 ("PM / devfreq: Add cpu based scaling support to passive governor") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
PM / devfreq: Fix kernel panic with cpu based scaling to passive gov
The cpufreq passive register notifier can PROBE_DEFER and the devfreq
struct is freed and then reallocaed on probe retry.
The current logic assume that the code can't PROBE_DEFER so the devfreq
struct in the this variable in devfreq_passive_data is assumed to be
(if already set) always correct.
This cause kernel panic as the code try to access the wrong address.
To correctly handle this, update the this variable in
devfreq_passive_data to the devfreq reallocated struct.
Fixes: 0de7288a58b9 ("PM / devfreq: Add cpu based scaling support to passive governor") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Ruili Ji [Wed, 22 Jun 2022 06:20:22 +0000 (14:20 +0800)]
drm/amdgpu: To flush tlb for MMHUB of RAVEN series
amdgpu: [mmhub0] no-retry page fault (src_id:0 ring:40 vmid:8 pasid:32769, for process test_basic pid 3305 thread test_basic pid 3305)
amdgpu: in page starting at address 0x00007ff990003000 from IH client 0x12 (VMC)
amdgpu: VM_L2_PROTECTION_FAULT_STATUS:0x00840051
amdgpu: Faulty UTCL2 client ID: MP1 (0x0)
amdgpu: MORE_FAULTS: 0x1
amdgpu: WALKER_ERROR: 0x0
amdgpu: PERMISSION_FAULTS: 0x5
amdgpu: MAPPING_ERROR: 0x0
amdgpu: RW: 0x1
When memory is allocated by kfd, no one triggers the tlb flush for MMHUB0.
There is page fault from MMHUB0.
v2:fix indentation
v3:change subject and fix indentation
Signed-off-by: Ruili Ji <ruiliji2@amd.com> Reviewed-by: Philip Yang <philip.yang@amd.com> Reviewed-by: Aaron Liu <aaron.liu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Carlos Llamas [Tue, 21 Jun 2022 20:39:21 +0000 (20:39 +0000)]
drm/fourcc: fix integer type usage in uapi header
Kernel uapi headers are supposed to use __[us]{8,16,32,64} types defined
by <linux/types.h> as opposed to 'uint32_t' and similar. See [1] for the
relevant discussion about this topic. In this particular case, the usage
of 'uint64_t' escaped headers_check as these macros are not being called
here. However, the following program triggers a compilation error:
#include <drm/drm_fourcc.h>
int main()
{
unsigned long x = AMD_FMT_MOD_CLEAR(RB);
return 0;
}
gcc error:
drm.c:5:27: error: ‘uint64_t’ undeclared (first use in this function)
5 | unsigned long x = AMD_FMT_MOD_CLEAR(RB);
| ^~~~~~~~~~~~~~~~~
This patch changes AMD_FMT_MOD_{SET,CLEAR} macros to use the correct
integer types, which fixes the above issue.
[1] https://lkml.org/lkml/2019/6/5/18
Fixes: 12f6834d9e40 ("drm/fourcc: Add AMD DRM modifiers.") Signed-off-by: Carlos Llamas <cmllamas@google.com> Reviewed-by: Simon Ser <contact@emersion.fr> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Wed, 29 Jun 2022 16:20:40 +0000 (09:20 -0700)]
Merge tag '5.19-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull ksmbd server fixes from Steve French:
- seek null check (don't use f_seek op directly and blindly)
- offset validation in FSCTL_SET_ZERO_DATA
- fallocate fix (relates e.g. to xfstests generic/091 and 263)
- two cleanup fixes
- fix socket settings on some arch
* tag '5.19-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: use vfs_llseek instead of dereferencing NULL
ksmbd: check invalid FileOffset and BeyondFinalZero in FSCTL_ZERO_DATA
ksmbd: set the range of bytes to zero without extending file size in FSCTL_ZERO_DATA
ksmbd: remove duplicate flag set in smb2_write
ksmbd: smbd: Remove useless license text when SPDX-License-Identifier is already used
ksmbd: use SOCK_NONBLOCK type for kernel_accept()
Jeff Layton [Mon, 6 Jun 2022 23:31:42 +0000 (19:31 -0400)]
ceph: wait on async create before checking caps for syncfs
Currently, we'll call ceph_check_caps, but if we're still waiting
on the reply, we'll end up spinning around on the same inode in
flush_dirty_session_caps. Wait for the async create reply before
flushing caps.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/55823 Fixes: 9580b74e7440 ("ceph: wait for async create reply before sending any cap messages") Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Darrick J. Wong [Sat, 25 Jun 2022 17:47:45 +0000 (10:47 -0700)]
xfs: dont treat rt extents beyond EOF as eofblocks to be cleared
On a system with a realtime volume and a 28k realtime extent,
generic/491 fails because the test opens a file on a frozen filesystem
and closing it causes xfs_release -> xfs_can_free_eofblocks to
mistakenly think that the the blocks of the realtime extent beyond EOF
are posteof blocks to be freed. Realtime extents cannot be partially
unmapped, so this is pointless. Worse yet, this triggers posteof
cleanup, which stalls on a transaction allocation, which is why the test
fails.
Teach the predicate to account for realtime extents properly.
Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de>
Darrick J. Wong [Sat, 25 Jun 2022 17:01:20 +0000 (10:01 -0700)]
xfs: don't hold xattr leaf buffers across transaction rolls
Now that we've established (again!) that empty xattr leaf buffers are
ok, we no longer need to bhold them to transactions when we're creating
new leaf blocks. Get rid of the entire mechanism, which should simplify
the xattr code quite a bit.
The original justification for using bhold here was to prevent the AIL
from trying to write the empty leaf block into the fs during the brief
time that we release the buffer lock. The reason for /that/ was to
prevent recovery from tripping over the empty ondisk block.
Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Darrick J. Wong [Fri, 24 Jun 2022 22:01:28 +0000 (15:01 -0700)]
xfs: empty xattr leaf header blocks are not corruption
TLDR: Revert commit d55e0e8e9bde ("xfs: detect empty attr leaf blocks in
xfs_attr3_leaf_verify") because it was wrong.
Every now and then we get a corruption report from the kernel or
xfs_repair about empty leaf blocks in the extended attribute structure.
We've long thought that these shouldn't be possible, but prior to 5.18
one would shake loose in the recoveryloop fstests about once a month.
A new addition to the xattr leaf block verifier in 5.19-rc1 makes this
happen every 7 minutes on my testing cloud. I added a ton of logging to
detect any time we set the header count on an xattr leaf block to zero.
This produced the following dmesg output on generic/388:
So now we know that someone is creating empty xattr leaf blocks as part
of converting a sf xattr structure into a leaf xattr structure. The
conversion routine logs any existing sf attributes in the same
transaction that creates the leaf block, so we know this is a setxattr
to a file that has no attributes at all.
Next, g/388 calls the shutdown ioctl and cycles the mount to trigger log
recovery. I also augmented buffer item recovery to call ->verify_struct
on any attr leaf blocks and complain if it finds a failure:
As you can see, the bhold keeps the leaf buffer locked and thus prevents
the *AIL* from tripping over the ichdr.count==0 check in the write
verifier. Unfortunately, it doesn't prevent the log from getting
flushed to disk, which sets up log recovery to fail.
So. It's clear that the kernel has always had the ability to persist
attr leaf blocks with ichdr.count==0, which means that it's part of the
ondisk format now.
Unfortunately, this check has been added and removed multiple times
throughout history. It first appeared in[1] kernel 3.10 as part of the
early V5 format patches. The check was later discovered to break log
recovery and hence disabled[2] during log recovery in kernel 4.10.
Simultaneously, the check was added[3] to xfs_repair 4.9.0 to try to
weed out the empty leaf blocks. This was still not correct because log
recovery would recover an empty attr leaf block successfully only for
regular xattr operations to trip over the empty block during of the
block during regular operation. Therefore, the check was removed
entirely[4] in kernel 5.7 but removal of the xfs_repair check was
forgotten. The continued complaints from xfs_repair lead to us
mistakenly re-adding[5] the verifier check for kernel 5.19. Remove it
once again.
[1] bc95d2878791 ("xfs: add CRCs to attr leaf blocks")
[2] 9ec1c35f5c91 ("xfs: ignore leaf attr ichdr.count in verifier
during log replay")
[3] f7140161 ("xfs_repair: junk leaf attribute if count == 0")
[4] aea9cf75384e ("xfs: don't fail verifier on empty attr3 leaf
block")
[5] d55e0e8e9bde ("xfs: detect empty attr leaf blocks in
xfs_attr3_leaf_verify")
Looking at the rest of the xattr code, it seems that files with empty
leaf blocks behave as expected -- listxattr reports no attributes;
getxattr on any xattr returns nothing as expected; removexattr does
nothing; and setxattr can add attributes just fine.
Original-bug: bc95d2878791 ("xfs: add CRCs to attr leaf blocks") Still-not-fixed-by: 9ec1c35f5c91 ("xfs: ignore leaf attr ichdr.count in verifier during log replay")
Removed-in: aea9cf75384e ("xfs: don't fail verifier on empty attr3 leaf block") Fixes: d55e0e8e9bde ("xfs: detect empty attr leaf blocks in xfs_attr3_leaf_verify") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Dave Chinner <dchinner@redhat.com>
Ruozhu Li [Thu, 23 Jun 2022 06:45:39 +0000 (14:45 +0800)]
nvme: fix regression when disconnect a recovering ctrl
We encountered a problem that the disconnect command hangs.
After analyzing the log and stack, we found that the triggering
process is as follows:
CPU0 CPU1
nvme_rdma_error_recovery_work
nvme_rdma_teardown_io_queues
nvme_do_delete_ctrl nvme_stop_queues
nvme_remove_namespaces
--clear ctrl->namespaces
nvme_start_queues
--no ns in ctrl->namespaces
nvme_ns_remove return(because ctrl is deleting)
blk_freeze_queue
blk_mq_freeze_queue_wait
--wait for ns to unquiesce to clean infligt IO, hang forever
This problem was not found in older kernels because we will flush
err work in nvme_stop_ctrl before nvme_remove_namespaces.It does not
seem to be modified for functional reasons, the patch can be revert
to solve the problem.
Revert commit 266322c690f3 ("nvme: remove the .stop_ctrl callout")
Signed-off-by: Ruozhu Li <liruozhu@huawei.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
Pablo Greco [Sat, 25 Jun 2022 12:15:02 +0000 (09:15 -0300)]
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG SX6000LNP (AKA SPECTRIX S40G)
ADATA XPG SPECTRIX S40G drives report bogus eui64 values that appear to
be the same across drives in one system. Quirk them out so they are
not marked as "non globally unique" duplicates.
Sagi Grimberg [Sun, 26 Jun 2022 09:24:51 +0000 (12:24 +0300)]
nvme-tcp: always fail a request when sending it failed
queue stoppage and inflight requests cancellation is fully fenced from
io_work and thus failing a request from this context. Hence we don't
need to try to guess from the socket retcode if this failure is because
the queue is about to be torn down or not.
We are perfectly safe to just fail it, the request will not be cancelled
later on.
This solves possible very long shutdown delays when the users issues a
'nvme disconnect-all'
Reported-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
Sagi Grimberg [Thu, 23 Jun 2022 21:49:53 +0000 (00:49 +0300)]
nvmet-tcp: fix regression in data_digest calculation
Data digest calculation iterates over command mapped iovec. However
since commit 8ce4bfe68658 we unmap the iovec before we handle the data
digest, and since commit 8162a936941e we clear nr_mapped when we unmap
the iov.
Instead of open-coding the command iov traversal, simply call
crypto_ahash_digest with the command sg that is already allocated (we
already do that for the send path). Rename nvmet_tcp_send_ddgst to
nvmet_tcp_calc_ddgst and call it from send and recv paths.
Fixes: 8162a936941e ("nvmet-tcp: add an helper to free the cmd buffers") Fixes: 8ce4bfe68658 ("nvmet-tcp: fix kmap leak when data digest in use") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de>
Michael Walle [Mon, 27 Jun 2022 17:06:43 +0000 (19:06 +0200)]
NFC: nxp-nci: don't print header length mismatch on i2c error
Don't print a misleading header length mismatch error if the i2c call
returns an error. Instead just return the error code without any error
message.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>