For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
After a call to console_unlock() in vcs_write() the vc_data struct can be
freed by vc_port_destruct(). Because of that, the struct vc_data pointer
must be reloaded in the while loop in vcs_write() after console_lock() to
avoid a UAF when vcs_size() is called.
Syzkaller reported a UAF in vcs_size().
BUG: KASAN: slab-use-after-free in vcs_size (drivers/tty/vt/vc_screen.c:215)
Read of size 4 at addr ffff8880beab89a8 by task repro_vcs_size/4119
The buggy address belongs to the object at ffff8880beab8800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 424 bytes inside of
freed 1024-byte region [ffff8880beab8800, ffff8880beab8c00)
It is weird to fetch the information from the inode over and over. Read
and write already have the needed information, so rewrite vcs_size to
accept a vc, attr and unicode and adapt vcs_lseek to that.
Also make sure all sites check the return value of vcs_size for errors.
And document it using kernel-doc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200818085706.12163-5-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8fb9ea65c9d1 ("vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF") Signed-off-by: Sasha Levin <sashal@kernel.org>
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
The USB ethernet gadget driver implements its own print macros which
call printk. Device drivers should use the device prints that print the
device name. Fortunately, the same macro names are defined in the header
file 'linux/usb/composite.h' and these use the device prints. Therefore,
remove the local definitions in the USB ethernet gadget driver and use
those in 'linux/usb/composite.h'. The only difference is that now the
device name is printed instead of the ethernet interface name.
Tested using ethernet gadget on Jetson AGX Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20230209125319.18589-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3c0f4f09c063 ("usb: gadget: u_ether: Fix host MAC address case") Signed-off-by: Sasha Levin <sashal@kernel.org>
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
clean_net() runs in workqueue while walking over the lists, grab mutex.
Fixes: 815fac68e781 ("netfilter: nftables: fix possible UAF over chains from packet path in netns") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add helper function to parse the set element key netlink attribute.
v4: No changes
v3: New patch
[sbrivio: refactor error paths and labels; use NFT_DATA_VALUE_MAXLEN
instead of sizeof(*key) in helper, value can be longer than that;
rebase] Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached.
It was reported that soft dirty tracking doesn't work when using the
Radix MMU.
The tracking is supposed to work by clearing the soft dirty bit for a
mapping and then write protecting the PTE. If/when the page is written
to, a page fault occurs and the soft dirty bit is added back via
pte_mkdirty(). For example in wp_page_reuse():
Unfortunately on radix _PAGE_SOFTDIRTY is being dropped by
radix__ptep_set_access_flags(), called from ptep_set_access_flags(),
meaning the soft dirty bit is not set even though the page has been
written to.
Fix it by adding _PAGE_SOFTDIRTY to the set of bits that are able to be
changed in radix__ptep_set_access_flags().
The P360 Tiny suffers from an irq storm issue like the T490s, so add
an entry for it to tpm_tis_dmi_table, and force polling. There also
previously was a report from the previous attempt to enable interrupts
that involved a ThinkPad L490. So an entry is added for it as well.
Cc: stable@vger.kernel.org Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/ Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the MClientSnap reqeust's op is not CEPH_SNAP_OP_SPLIT the
request may still contain a list of 'split_realms', and we need
to skip it anyway. Or it will be parsed as a corrupt snaptrace.
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
If a vCPU is outside guest mode and is scheduled out, it might be in the
process of making a memory access. A problem occurs if another vCPU uses
the PV TLB flush feature during the period when the vCPU is scheduled
out, and a virtual address has already been translated but has not yet
been accessed, because this is equivalent to using a stale TLB entry.
To avoid this, only report a vCPU as preempted if sure that the guest
is at an instruction boundary. A rescheduling request will be delivered
to the host physical CPU as an external interrupt, so for simplicity
consider any vmexit *not* instruction boundary except for external
interrupts.
It would in principle be okay to report the vCPU as preempted also
if it is sleeping in kvm_vcpu_block(): a TLB flush IPI will incur the
vmentry/vmexit overhead unnecessarily, and optimistic spinning is
also unlikely to succeed. However, leave it for later because right
now kvm_vcpu_check_block() is doing memory accesses. Even
though the TLB flush issue only applies to virtual memory address,
it's very much preferrable to be conservative.
Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[OP: use VCPU_STAT() for debugfs entries] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: ea3f54dd9351 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control message provided by J1939 support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.
Link: https://github.com/hartkopp/can-isotp/issues/59 Cc: Oleksij Rempel <o.rempel@pengutronix.de> Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Fixes: 877b9bba3266 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/20230505110308.81087-3-mkl@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_line_out_pfx() may trigger an Oops by overflowing the static array
with more than 8 channels. This was reported for MacBookPro 12,1 with
Cirrus codec.
As a workaround, extend for the 9.1 channels and also fix the
potential Oops by unifying the code paths accessing the same array
with the proper size check.
This patch fixes negative indexing of buf array in pin_assignment_show
when get_current_pin_assignments returns 0 i.e. no compatible pin
assignments are found.
When the dwc3 device is runtime suspended, various required clocks are in
disabled state and it is not guaranteed that access to any registers would
work. Depending on the SoC glue, a register read could be as benign as
returning 0 or be fatal enough to hang the system.
In order to prevent such scenarios of fatal errors, make sure to resume
dwc3 then allow the function to proceed.
OverCurrent condition is not standardized in the UHCI spec.
Zhaoxin UHCI controllers report OverCurrent bit active off.
In order to handle OverCurrent condition correctly, the uhci-hcd
driver needs to be told to expect the active-off behavior.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20230423105952.4526-1-WeitaoWang-oc@zhaoxin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
The syzbot fuzzer found a problem in the usbtmc driver: When a user
submits an ioctl for a 0-length control transfer, the driver does not
check that the direction is set to OUT:
CPU: 0 PID: 29770 Comm: syz-executor.0 Not tainted 6.3.0-rc6-syzkaller-gc478e5b17829 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: d49a2a41710f ("igb: PCI-Express 82575 Gigabit Ethernet driver") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: c4897a27ebe9 ("cassini: use request_firmware") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: 6601d5a7c259 ("net: bcmgenet: connect and disconnect from the PHY state machine") Fixes: 93e0401e0fc0 ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: 6601d5a7c259 ("net: bcmgenet: connect and disconnect from the PHY state machine") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
The empty stub functions are defined as global functions, which
causes a warning because of missing prototypes:
drivers/gpu/drm/exynos/exynos_drm_g2d.h:37:5: error: no previous prototype for 'g2d_open'
drivers/gpu/drm/exynos/exynos_drm_g2d.h:42:5: error: no previous prototype for 'g2d_close'
Mark them as 'static inline' to avoid the warning and to make
them behave as intended.
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 396acb0485ed ("net: hns3: Add support to reset the enet/ring mgmt layer") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 211c0939a183 ("net: hns3: adjust the process of PF reset") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit f6ed7126ce09 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: f6ed7126ce09 ("erspan: build the header with the right proto according to erspan_ver") Fixes: f2bf205dab51 ("ip6_gre: add erspan v2 support") Reported-by: Kevin Traynor <ktraynor@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the
following sequence of events:
1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
add ... external". "ip" ignores "[o]seq" if "external" is specified,
so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:
Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by
making o_seqno atomic_t.
As mentioned by Eric Dumazet in commit 6f5ce4d7ff17 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.
Maybe a better fix would be:
1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if
they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
with "oseq".
Unfortunately, that would break userspace.
We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 359dae890f7b ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode. According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.
Fixes: 3d8fd70921d8 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
1. During ip6gretap device initialization, tunnel->tun_hlen (e.g. 4) is
calculated based on old flags (see ip6gre_calc_hlen());
2. packet_snd() reserves header room for skb A, assuming
tunnel->tun_hlen is 4;
3. Later (in clsact Qdisc), the eBPF program sets a new tunnel key for
skb A using bpf_skb_set_tunnel_key() (see _ip6gretap_set_tunnel());
4. __gre6_xmit() detects the new tunnel key, and recalculates
"tun_hlen" (e.g. 12) based on new flags (e.g. TUNNEL_KEY and
TUNNEL_SEQ);
5. gre_build_header() calls skb_push() with insufficient reserved header
room, triggering the BUG.
As sugguested by Cong, fix it by moving the call to skb_cow_head() after
the recalculation of tun_hlen.
ip netns add at_ns0
ip link add veth0 type veth peer name veth1
ip link set veth0 netns at_ns0
ip netns exec at_ns0 ip addr add 172.16.1.100/24 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip link set dev veth1 up mtu 1500
ip addr add dev veth1 172.16.1.200/24
ip netns exec at_ns0 ip addr add ::11/96 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip addr add dev veth1 ::22/96
ip link set dev veth1 up
ip netns exec at_ns0 \
ip link add dev ip6gretap00 type ip6gretap seq flowlabel 0xbcdef key 2 \
local ::11 remote ::22
ip netns exec at_ns0 ip addr add dev ip6gretap00 10.1.1.100/24
ip netns exec at_ns0 ip addr add dev ip6gretap00 fc80::100/96
ip netns exec at_ns0 ip link set dev ip6gretap00 up
ip link add dev ip6gretap11 type ip6gretap external
ip addr add dev ip6gretap11 10.1.1.200/24
ip addr add dev ip6gretap11 fc80::200/24
ip link set dev ip6gretap11 up
tc qdisc add dev ip6gretap11 clsact
tc filter add dev ip6gretap11 egress bpf da obj $OBJ sec ip6gretap_set_tunnel
tc filter add dev ip6gretap11 ingress bpf da obj $OBJ sec ip6gretap_get_tunnel
ping6 -c 3 -w 10 -q ::11
Fixes: 4469230eef55 ("ip6_gre: add ip6 gre and gretap collect_md mode") Reported-by: Feng Zhou <zhoufeng.zf@bytedance.com> Co-developed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: e9d736dd26b5 ("VSOCK: Introduce VM Sockets") Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This code was supposed to return an error code if init_stream()
failed, but it instead freed dg00x->rx_stream and returned success.
This potentially leads to a use after free.
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
System-wide TSC read could cause a drift in C0 percentage calculation.
Because if first TSC is read and then one by one mperf is read for all
cpus, this introduces drift between mperf reading of later CPUs and TSC
reading. To lower this drift read TSC per CPU and also just after mperf
read. This technique improves C0 percentage calculation in Mperf monitor.
There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()
snd_soc_register_card()
-> snd_soc_bind_card()
-> snd_soc_add_pcm_runtime()
-> adding cpu dai
-> adding codec dai
-> adding platform component.
So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.
As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.
When loading a free space cache from disk, at __load_free_space_cache(),
if we fail to insert a bitmap entry, we still increment the number of
total bitmaps in the btrfs_free_space_ctl structure, which is incorrect
since we failed to add the bitmap entry. On error we then empty the
cache by calling __btrfs_remove_free_space_cache(), which will result
in getting the total bitmaps counter set to 1.
A failure to load a free space cache is not critical, so if a failure
happens we just rebuild the cache by scanning the extent tree, which
happens at block-group.c:caching_thread(). Yet the failure will result
in having the total bitmaps of the btrfs_free_space_ctl always bigger
by 1 then the number of bitmap entries we have. So fix this by having
the total bitmaps counter be incremented only if we successfully added
the bitmap entry.
Fixes: 63f86f1f7733 ("Btrfs: add a io_ctl struct and helpers for dealing with the space cache") Reviewed-by: Anand Jain <anand.jain@oracle.com> CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The former is going away as part of the inode map removal so switch
callers to btrfs_find_free_objectid. No functional changes since with
INODE_MAP disabled (default) find_free_objectid was called anyway.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 0004ff15ea26 ("btrfs: fix space cache inconsistency after error loading it from disk") Signed-off-by: Sasha Levin <sashal@kernel.org>
Wired GIP devices present multiple interfaces with the same USB identification
other than the interface number. This adds constants for differentiating two of
them and uses them where appropriate
When an overflow occurs in the PRI queue, the SMMU toggles the overflow
flag in the PROD register. To exit the overflow condition, the PRI thread
is supposed to acknowledge it by toggling this flag in the CONS register.
Unacknowledged overflow causes the queue to stop adding anything new.
Currently, the priq thread always writes the CONS register back to the
SMMU after clearing the queue.
The writeback is not necessary if the OVFLG in the PROD register has not
been changed, no overflow has occured.
This commit checks the difference of the overflow flag between CONS and
PROD register. If it's different, toggles the OVACKFLG flag in the CONS
register and write it to the SMMU.
The situation is similar for the event queue.
The acknowledge register is also toggled after clearing the event
queue but never propagated to the hardware. This would only be done the
next time when executing evtq thread.
Unacknowledged event queue overflow doesn't affect the event
queue, because the SMMU still adds elements to that queue when the
overflow condition is active.
But it feel nicer to keep SMMU in sync when possible, so use the same
way here as well.
Older gcc versions get confused by comparing a u32 value to a negative
constant in a switch()/case block:
drivers/clk/tegra/clk-tegra20.c: In function 'tegra20_clk_measure_input_freq':
drivers/clk/tegra/clk-tegra20.c:581:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_12MHZ:
^~~~
drivers/clk/tegra/clk-tegra20.c:593:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_26MHZ:
So we have sizeof(*packet) + IB_MGMT_RMPP_HDR == 140 bytes
Then the address of the flex-array member (for which only 36 bytes were
allocated) is casted and copied into a pointer to struct ib_rmpp_mad,
which, in turn, is of size 256 bytes:
The thing is that those 36 bytes allocated for flex-array member data
in struct ib_user_mad onlly account for the size of both struct ib_mad_hdr
and struct ib_rmpp_hdr, but nothing is left for array u8 data[220].
So, the compiler is legitimately complaining about accessing an object
for which not enough memory was allocated.
Apparently, the only members of struct ib_rmpp_mad that are relevant
(that are actually being used) in function ib_umad_write() are mad_hdr
and rmpp_hdr. So, instead of casting packet->mad.data to
(struct ib_rmpp_mad *) create a new structure
mcb-pci requests a fixed-size memory region to parse the chameleon
table, however, if the chameleon table is smaller that the allocated
region, it could overlap with the IP Cores' memory regions.
After parsing the chameleon table, drop/reallocate the memory region
with the actual chameleon table size.
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.
In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Frank Wang <frank.wang@rock-chips.com> Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Now that USB HID++ devices can gather a serial number that matches the
one that would be gathered when connected through a Unifying receiver,
remove the last difference by dropping the product ID as devices
usually have different product IDs when connected through USB or
Unifying.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying before patch: 4067-e8-ce-cd-45
- USB before patch: c086-e8-ce-cd-45
- Unifying and USB after patch: e8-ce-cd-45
For devices that support the 0x0003 feature (Device Information) version 4,
set the serial based on the output of that feature, rather than relying
on the usbhid code setting the USB serial.
This should allow the serial when connected through USB to (nearly)
match the one when connected through a unifying receiver.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying: 4067-e8-ce-cd-45
- USB before patch: 017C385C3837
- USB after patch: c086-e8-ce-cd-45
conn->chan_lock isn't acquired before l2cap_get_chan_by_scid,
if l2cap_get_chan_by_scid returns NULL, then 'bad unlock balance'
is triggered.
Reported-by: syzbot+9519d6b5b79cf7787cf3@syzkaller.appspotmail.com Link: https://lore.kernel.org/all/000000000000894f5f05f95e9f4d@google.com/ Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A received TKIP key may be up to 32 bytes because it may contain
MIC rx/tx keys too. These are not used by iwl and copying these
over overflows the iwl_keyinfo.key field.
Add a check to not copy more data to iwl_keyinfo.key then will fit.
This fixes backtraces like this one:
memcpy: detected field-spanning write (size 32) of single field "sta_cmd.key.key" at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 (size 16)
WARNING: CPU: 1 PID: 946 at drivers/net/wireless/intel/iwlwifi/dvm/sta.c:1103 iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Hardware name: Dell Inc. Latitude E6430/0H3MT5, BIOS A21 05/08/2017
RIP: 0010:iwlagn_send_sta_key+0x375/0x390 [iwldvm]
<snip>
Call Trace:
<TASK>
iwl_set_dynamic_key+0x1f0/0x220 [iwldvm]
iwlagn_mac_set_key+0x1e4/0x280 [iwldvm]
drv_set_key+0xa4/0x1b0 [mac80211]
ieee80211_key_enable_hw_accel+0xa8/0x2d0 [mac80211]
ieee80211_key_replace+0x22d/0x8e0 [mac80211]
<snip>
If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.
This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.
It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.
iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260
During umount(), if cp_error is set, f2fs_wait_on_all_pages() should
not stop waiting all F2FS_WB_CP_DATA pages to be writebacked, otherwise,
fsync_node_num can be non-zero after f2fs_wait_on_all_pages() causing
this bug.
In this case, to avoid deadloop in f2fs_wait_on_all_pages(), it needs
to drop all dirty pages rather than redirtying them.
When the length of best extent found is less than the length of goal extent
we need to make sure that the best extent atleast covers the start of the
original request. This is done by adjusting the ac_b_ex.fe_logical (logical
start) of the extent.
While doing so, the current logic sometimes results in the best extent's
logical range overflowing the goal extent. Since this best extent is later
added to the inode preallocation list, we have a possibility of introducing
overlapping preallocations. This is discussed in detail here [1].
As per Jan's suggestion, to fix this, replace the existing logic with the
below logic for adjusting best extent as it keeps fragmentation in check
while ensuring logical range of best extent doesn't overflow out of goal
extent:
1. Check if best extent can be kept at end of goal range and still cover
original start.
2. Else, check if best extent can be kept at start of goal range and still
cover original start.
3. Else, keep the best extent at start of original request.
Also, add a few extra BUG_ONs that might help catch errors faster.
We need to set ac_g_ex to notify the goal start used in
ext4_mb_find_by_goal. Set ac_g_ex instead of ac_f_ex in
ext4_mb_normalize_request.
Besides we should assure goal start is in range [first_data_block,
blocks_count) as ext4_mb_initialize_context does.
[ Added a check to make sure size is less than ar->pright; otherwise
we could end up passing an underflowed value of ar->pright - size to
ext4_get_group_no_and_offset(), which will trigger a BUG_ON later on.
- TYT ]
The maximum allowed height of an inode's metadata tree depends on the
filesystem block size; it is lower for bigger-block filesystems. When
reading in an inode, make sure that the height doesn't exceed the
maximum allowed height.
Arrays like sd_heightsize are sized to be big enough for any filesystem
block size; they will often be slightly bigger than what's needed for a
specific filesystem.
Reported-by: syzbot+45d4691b1ed3c48eba05@syzkaller.appspotmail.com Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
mptlan_probe() calls mpt_register_lan_device() which initializes the
&priv->post_buckets_task workqueue. A call to
mpt_lan_wake_post_buckets_task() will subsequently start the work.
During driver unload in mptlan_remove() the following race may occur:
When calling irq_set_affinity_notifier() with NULL at the notify
argument, it will cause freeing of the glue pointer in the
corresponding array entry but will leave the pointer in the array. A
subsequent call to free_irq_cpu_rmap() will try to free this entry again
leading to possible use after free.
Fix that by setting NULL to the array entry and checking that we have
non-zero at the array entry when iterating over the array in
free_irq_cpu_rmap().
The current code does not suffer from this since there are no cases
where irq_set_affinity_notifier(irq, NULL) (note the NULL passed for the
notify arg) is called, followed by a call to free_irq_cpu_rmap() so we
don't hit and issue. Subsequent patches in this series excersize this
flow, hence the required fix.
Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Eli Cohen <elic@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When setting the XPS value of a TX queue, warn the user once if the
index of the queue is greater than the number of allocated TX queues.
Previously, this scenario went uncaught. In the best case, it resulted
in unnecessary allocations. In the worst case, it resulted in
out-of-bounds memory references through calls to `netdev_get_tx_queue(
dev, index)`. Therefore, it is important to inform the user but not
worth returning an error and risk downing the netdevice.
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
drivers/net/ethernet/pasemi/pasemi_mac.c:1665:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = pasemi_mac_start_tx,
^~~~~~~~~~~~~~~~~~~
1 error generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of
pasemi_mac_start_tx() to match the prototype's to resolve the warning.
While PowerPC does not currently implement support for kCFI, it could in
the future, which means this warning becomes a fatal CFI failure at run
time.
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow.
Check that log of block size stored in the superblock has sensible
value. Otherwise the shift computing the block size can overflow leading
to undefined behavior.
Reported-by: syzbot+4fec412f59eba8c01b77@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log