fixed a problem whereby clock_nanosleep() followed by clock_gettime() could
allow a task to wake early. It addressed the problem by calling the scheduling
classes update_curr() when the cputimer starts.
Said change induced a considerable performance regression on the syscalls
times() and clock_gettimes(CLOCK_PROCESS_CPUTIME_ID). There are some
debuggers and applications that monitor their own performance that
accidentally depend on the performance of these specific calls.
This patch mitigates the performace loss by prefetching data in the CPU
cache, as stalls due to cache misses appear to be where most time is spent
in our benchmarks.
Here are the performance gain of this patch over v4.7-rc7 on a Sandy Bridge
box with 32 logical cores and 2 NUMA nodes. The test is repeated with a
variable number of threads, from 2 to 4*num_cpus; the results are in
seconds and correspond to the average of 10 runs; the percentage gain is
computed with (before-after)/before so a positive value is an improvement
(it's faster). The improvement varies between a few percents for 5-20
threads and more than 10% for 2 or >20 threads.
pound_clock_gettime and pound_clock_gettime are two benchmarks included in
the MMTests framework. They launch a given number of threads which
repeatedly call times() or clock_gettimes(). The results above can be
reproduced with cloning MMTests from github.com and running the "poundtime"
workload:
The above will run "poundtime" measuring the kernel currently running on
the machine; Once a new kernel is installed and the machine rebooted,
running again
$ cd mmtests
$ ./run-mmtests.sh --run-monitor $(uname -r)
will produce results to compare with. A comparison table will be output
with:
$ cd mmtests/work/log
$ ../../compare-kernels.sh
the table will contain a lot of entries; grepping for "Amean" (as in
"arithmetic mean") will give the tables presented above. The source code
for the two benchmarks is reported at the end of this changelog for
clairity.
The cache misses addressed by this patch were found using a combination of
`perf top`, `perf record` and `perf annotate`. The incriminated lines were
found to be
struct sched_entity *curr = cfs_rq->curr;
and
delta_exec = now - curr->exec_start;
in the function update_curr() from kernel/sched/fair.c. This patch
prefetches the data from memory just before update_curr is called in the
interested execution path.
A comparison of the total number of cycles before and after the patch
follows; the data is obtained using `perf stat -r 10 -ddd <program>`
running over the same sequence of number of threads used above (a positive
gain is an improvement):
As a final note, the following shows the evolution of performance figures
in the "poundtime" benchmark and pinpoints commit 6e998916dfe3
("sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency") as a
major source of degradation, mostly unaddressed to this day (figures
expressed in seconds).
Current code in cpudeadline.c has a bug in re-heapifying when adding a
new element at the end of the heap, because a deadline value of 0 is
temporarily set in the new elem, then cpudl_change_key() is called
with the actual elem deadline as param.
However, the function compares the new deadline to set with the one
previously in the elem, which is 0. So, if current absolute deadlines
grew so much to have negative values as s64, the comparison in
cpudl_change_key() makes the wrong decision. Instead, as from
dl_time_before(), the kernel should handle correctly abs deadlines
wrap-arounds.
This patch fixes the problem with a minimally invasive change that
forces cpudl_change_key() to heapify up in this case.
Signed-off-by: Tommaso Cucinotta <tommaso.cucinotta@sssup.it> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Luca Abeni <luca.abeni@unitn.it> Cc: Juri Lelli <juri.lelli@arm.com> Cc: Juri Lelli <juri.lelli@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1468921493-10054-2-git-send-email-tommaso.cucinotta@sssup.it Signed-off-by: Ingo Molnar <mingo@kernel.org>
Geert Uytterhoeven reports:
"This change seems to have an (unintendent?) side-effect.
Before, pr_*() calls without a trailing newline characters would be
printed with a newline character appended, both on the console and in
the output of the dmesg command.
After this commit, no new line character is appended, and the output
of the next pr_*() call of the same type may be appended, like in:
- Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000
- Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)
+ Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)"
Joe Perches says:
"No, that is not intentional.
The newline handling code inside vprintk_emit is a bit involved and
for now I suggest a revert until this has all the same behavior as
earlier"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Requested-by: Joe Perches <joe@perches.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 9 Aug 2016 17:34:09 +0000 (10:34 -0700)]
Merge tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix tick_stop tracepoint symbols for user export.
Luiz Capitulino noticed that the tick_stop tracepoint wasn't being
parsed properly by the tracing user space tools.
This was due to the TRACE_DEFINE_ENUM() being set to a define, when it
should have been set to the enum itself. The define was of the MASK
that used the BIT to shift. The BIT was the enum and by adding that,
everything gets converted nicely. The MASK is still kept just in case
it gets converted to an enum in the future"
* tag 'trace-v4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix tick_stop tracepoint symbols for user export
Linus Torvalds [Tue, 9 Aug 2016 17:30:07 +0000 (10:30 -0700)]
Merge tag 'gcc-plugin-infrastructure-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugin improvements from Kees Cook:
"Several fixes/improvements for the gcc plugin infrastructure:
- fix a problem with gcc plugins interfering with cc-option tests.
- abort more gracefully when gcc plugin headers or compiler support
is missing.
- improve the gcc plugin rule generation to be more dynamic, pass
arguments, and build from subdirectories"
* tag 'gcc-plugin-infrastructure-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Add support for plugin subdirectories
gcc-plugins: Automate make rule generation
gcc-plugins: Add support for passing plugin arguments
gcc-plugins: abort builds cleanly when not supported
kbuild: no gcc-plugins during cc-option tests
Linus Torvalds [Tue, 9 Aug 2016 17:20:21 +0000 (10:20 -0700)]
Merge tag 'drm-fixes-for-4.8-rc2' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This contains a bunch of amdgpu fixes, and some i915 regression fixes.
It also contains some fixes for an older regression with some EDID
changes and some 6bpc panels.
Then there are the lockdep, cirrus and rcar-du regression fixes from
this window"
* tag 'drm-fixes-for-4.8-rc2' of git://people.freedesktop.org/~airlied/linux:
drm/cirrus: Fix NULL pointer dereference when registering the fbdev
drm/edid: Set 8 bpc color depth for displays with "DFP 1.x compliant TMDS".
drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"
drm/edid: Add 6 bpc quirk for display AEO model 0.
drm: Paper over locking inversion after registration rework
drm: rcar-du: Link HDMI encoder with bridge
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/i915/fbdev: Check for the framebuffer before use
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
Brian King [Mon, 8 Aug 2016 22:53:12 +0000 (17:53 -0500)]
ipr: Fix sync scsi scan
Commit b195d5e2bffd ("ipr: Wait to do async scan until scsi host is
initialized") fixed async scan for ipr, but broke sync scan for ipr.
This fixes sync scan back up.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: memcontrol: only mark charged pages with PageKmemcg
To distinguish non-slab pages charged to kmemcg we mark them PageKmemcg,
which sets page->_mapcount to -512. Currently, we set/clear PageKmemcg
in __alloc_pages_nodemask()/free_pages_prepare() for any page allocated
with __GFP_ACCOUNT, including those that aren't actually charged to any
cgroup, i.e. allocated from the root cgroup context. To avoid overhead
in case cgroups are not used, we only do that if memcg_kmem_enabled() is
true. The latter is set iff there are kmem-enabled memory cgroups
(online or offline). The root cgroup is not considered kmem-enabled.
As a result, if a page is allocated with __GFP_ACCOUNT for the root
cgroup when there are kmem-enabled memory cgroups and is freed after all
kmem-enabled memory cgroups were removed, e.g.
# no memory cgroups has been created yet, create one
mkdir /sys/fs/cgroup/memory/test
# run something allocating pages with __GFP_ACCOUNT, e.g.
# a program using pipe
dmesg | tail
# remove the memory cgroup
rmdir /sys/fs/cgroup/memory/test
we'll get bad page state bug complaining about page->_mapcount != -1:
BUG: Bad page state in process swapper/0 pfn:1fd945c
page:ffffea007f651700 count:0 mapcount:-511 mapping: (null) index:0x0
flags: 0x1000000000000000()
To avoid that, let's mark with PageKmemcg only those pages that are
actually charged to and hence pin a non-root memory cgroup.
Fixes: 4949148ad433 ("mm: charge/uncharge kmemcg from generic page allocator paths") Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
User space tools have no idea how to parse "TICK_DEP_BIT_SCHED" or the other
symbols used to do the bit shifting. The reason is that the conversion was
done with using the TICK_DEP_MASK_* symbols which are just macros that
convert to the BIT shift itself (with the exception of NONE, which was
converted properly, because it doesn't use bits, and is defined as zero).
The TICK_DEP_BIT_* needs to be denoted by TRACE_DEFINE_ENUM() in order to
have this properly converted for user space tools to parse this event.
Cc: stable@vger.kernel.org Cc: Frederic Weisbecker <fweisbec@gmail.com> Fixes: e6e6cc22e067 ("nohz: Use enum code for tick stop failure tracing message") Reported-by: Luiz Capitulino <lcapitulino@redhat.com> Tested-by: Luiz Capitulino <lcapitulino@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Boris Brezillon [Tue, 9 Aug 2016 00:16:18 +0000 (02:16 +0200)]
drm/cirrus: Fix NULL pointer dereference when registering the fbdev
cirrus_modeset_init() is initializing/registering the emulated fbdev
and, since commit c61b93fe51b1 ("drm/atomic: Fix remaining places where
!funcs->best_encoder is valid"), DRM internals can access/test some of
the fields in mode_config->funcs as part of the fbdev registration
process.
Make sure dev->mode_config.funcs is properly set to avoid dereferencing
a NULL pointer.
Reported-by: Mike Marshall <hubcap@omnibond.com> Reported-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: c61b93fe51b1 ("drm/atomic: Fix remaining places where !funcs->best_encoder is valid") Signed-off-by: Dave Airlie <airlied@redhat.com>
Kees Cook [Sat, 18 Jun 2016 06:11:12 +0000 (23:11 -0700)]
gcc-plugins: abort builds cleanly when not supported
When the compiler doesn't support gcc plugins (either due to missing
headers or too old a version), report the problem and abort the build
instead of emitting a warning and letting the build founder with arcane
compiler errors.
Emese Revfy [Sat, 18 Jun 2016 06:28:34 +0000 (23:28 -0700)]
kbuild: no gcc-plugins during cc-option tests
The gcc-plugins arguments should not be included when performing
cc-option tests.
Steps to reproduce:
1) make mrproper
2) make defconfig
3) enable GCC_PLUGINS, GCC_PLUGIN_CYC_COMPLEXITY
4) enable FUNCTION_TRACER (it will select other options as well)
5) make && make modules
Mario Kleiner [Wed, 6 Jul 2016 10:05:48 +0000 (12:05 +0200)]
drm/edid: Set 8 bpc color depth for displays with "DFP 1.x compliant TMDS".
According to E-EDID spec 1.3, table 3.9, a digital video sink with the
"DFP 1.x compliant TMDS" bit set is "signal compatible with VESA DFP 1.x
TMDS CRGB, 1 pixel / clock, up to 8 bits / color MSB aligned".
For such displays, the DFP spec 1.0, section 3.10 "EDID support" says:
"If the DFP monitor only supports EDID 1.X (1.1, 1.2, etc.)
without extensions, the host will make the following assumptions:
1. 24-bit MSB-aligned RGB TFT
2. DE polarity is active high
3. H and V syncs are active high
4. Established CRT timings will be used
5. Dithering will not be enabled on the host"
So if we don't know the bit depth of the display from additional
colorimetry info we should assume 8 bpc / 24 bpp by default.
This patch adds info->bpc = 8 assignement for that case.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Mario Kleiner [Wed, 6 Jul 2016 10:05:45 +0000 (12:05 +0200)]
drm/i915/dp: Revert "drm/i915/dp: fall back to 18 bpp when sink capability is unknown"
This reverts commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")
This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.
Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.
The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.
DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.
Please backport to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Cc: stable@vger.kernel.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Mario Kleiner [Wed, 6 Jul 2016 10:05:44 +0000 (12:05 +0200)]
drm/edid: Add 6 bpc quirk for display AEO model 0.
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: stable@vger.kernel.org Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Mon, 8 Aug 2016 22:39:24 +0000 (15:39 -0700)]
Merge tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull lkdtm update from Kees Cook:
"Fix rebuild problem with LKDTM's rodata test"
[ This, and the usercopy branch, both came in before the merge window
closed, but ended up in my 'need to look more' queue and thus got
merged only after rc1 was out ]
* tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lkdtm: Fix targets for objcopy usage
lkdtm: fix false positive warning from -Wmaybe-uninitialized
Linus Torvalds [Mon, 8 Aug 2016 21:48:14 +0000 (14:48 -0700)]
Merge tag 'usercopy-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull usercopy protection from Kees Cook:
"Tbhis implements HARDENED_USERCOPY verification of copy_to_user and
copy_from_user bounds checking for most architectures on SLAB and
SLUB"
Linus Torvalds [Mon, 8 Aug 2016 20:02:01 +0000 (13:02 -0700)]
unsafe_[get|put]_user: change interface to use a error target label
When I initially added the unsafe_[get|put]_user() helpers in commit 5b24a7a2aa20 ("Add 'unsafe' user access functions for batched
accesses"), I made the mistake of modeling the interface on our
traditional __[get|put]_user() functions, which return zero on success,
or -EFAULT on failure.
That interface is fairly easy to use, but it's actually fairly nasty for
good code generation, since it essentially forces the caller to check
the error value for each access.
In particular, since the error handling is already internally
implemented with an exception handler, and we already use "asm goto" for
various other things, we could fairly easily make the error cases just
jump directly to an error label instead, and avoid the need for explicit
checking after each operation.
So switch the interface to pass in an error label, rather than checking
the error value in the caller. Best do it now before we start growing
more users (the signal handling code in particular would be a good place
to use the new interface).
So rather than
if (unsafe_get_user(x, ptr))
... handle error ..
the interface is now
unsafe_get_user(x, ptr, label);
where an error during the user mode fetch will now just cause a jump to
'label' in the caller.
Right now the actual _implementation_ of this all still ends up being a
"if (err) goto label", and does not take advantage of any exception
label tricks, but for "unsafe_put_user()" in particular it should be
fairly straightforward to convert to using the exception table model.
Note that "unsafe_get_user()" is much harder to convert to a clever
exception table model, because current versions of gcc do not allow the
use of "asm goto" (for the exception) with output values (for the actual
value to be fetched). But that is hopefully not a limitation in the
long term.
[ Also note that it might be a good idea to switch unsafe_get_user() to
actually _return_ the value it fetches from user space, but this
commit only changes the error handling semantics ]
Andreas Ziegler [Thu, 4 Aug 2016 07:52:09 +0000 (09:52 +0200)]
printk: Remove unnecessary #ifdef CONFIG_PRINTK
In commit 874f9c7da9a4 ("printk: create pr_<level> functions"), new
pr_level defines were added to printk.c.
These new defines are guarded by an #ifdef CONFIG_PRINTK - however,
there is already a surrounding #ifdef CONFIG_PRINTK starting a lot
earlier in line 249 which means the newly introduced #ifdef is
unnecessary.
Let's remove it to avoid confusion.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de> Cc: Joe Perches <joe@perches.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Fixes: f5967101e9de ("x86/hweight: Get rid of the special calling convention") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Mon, 8 Aug 2016 06:45:33 +0000 (16:45 +1000)]
Merge branch 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux into drm-next
A few fixes for amdgpu and ttm for 4.8
- fix a ttm regression caused by the new pipelining code
- fixes for mullins on amdgpu
- updated golden settings for amdgpu
* 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
Dave Airlie [Mon, 8 Aug 2016 06:16:26 +0000 (16:16 +1000)]
Merge tag 'drm-intel-next-fixes-2016-08-05' of git://anongit.freedesktop.org/drm-intel into drm-next
3 intel fixes.
* tag 'drm-intel-next-fixes-2016-08-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915/fbdev: Check for the framebuffer before use
drm/i915: Never fully mask the the EI up rps interrupt on SNB/IVB
drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL
Daniel Vetter [Thu, 4 Aug 2016 16:35:48 +0000 (18:35 +0200)]
drm: Paper over locking inversion after registration rework
drm_connector_register_all requires a few too many locks because our
connector_list locking is busted. Add another FIXME+hack to work
around this. This should address the below lockdep splat:
======================================================
[ INFO: possible circular locking dependency detected ]
4.7.0-rc5+ #524 Tainted: G O
-------------------------------------------------------
kworker/u8:0/6 is trying to acquire lock:
(&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff815afde0>] drm_modeset_lock_all+0x40/0x120
but task is already holding lock:
((fb_notifier_list).rwsem){++++.+}, at: [<ffffffff810ac195>] __blocking_notifier_call_chain+0x35/0x70
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
v2: Rebase onto the right branch (hand-editing patches ftw) and add more
reporters.
Reported-by: Imre Deak <imre.deak@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-by: Jiri Kosina <jikos@kernel.org> Cc: Jiri Kosina <jikos@kernel.org> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
The conversion of the rcar-du driver from the I2C slave encoder to the
DRM bridge API left the HDMI encoder's bridge pointer NULL, preventing
the bridge from being handled automatically by the DRM core. Fix it.
Fixes: 1d926114d8f4 ("drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder") Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Sun, 7 Aug 2016 23:38:45 +0000 (16:38 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
Linus Torvalds [Sun, 7 Aug 2016 23:35:08 +0000 (16:35 -0700)]
Merge tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
Jens Axboe [Fri, 5 Aug 2016 21:35:16 +0000 (15:35 -0600)]
block: rename bio bi_rw to bi_opf
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
Jens Axboe [Fri, 5 Aug 2016 14:11:04 +0000 (08:11 -0600)]
block/mm: make bdev_ops->rw_page() take a bool for read/write
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds [Sun, 7 Aug 2016 14:23:17 +0000 (10:23 -0400)]
Merge tag 'doc-4.8-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three fixes for the docs build, including removing an annoying warning
on 'make help' if sphinx isn't present"
* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
Documenation: update cgroup's document path
Documentation/sphinx: do not warn about missing tools in 'make help'
Linus Torvalds [Sun, 7 Aug 2016 14:13:14 +0000 (10:13 -0400)]
Merge tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc
Pull binfmt_misc update from James Bottomley:
"This update is to allow architecture emulation containers to function
such that the emulation binary can be housed outside the container
itself. The container and fs parts both have acks from relevant
experts.
To use the new feature you have to add an F option to your binfmt_misc
configuration"
From the docs:
"The usual behaviour of binfmt_misc is to spawn the binary lazily when
the misc format file is invoked. However, this doesn't work very well
in the face of mount namespaces and changeroots, so the F mode opens
the binary as soon as the emulation is installed and uses the opened
image to spawn the emulator, meaning it is always available once
installed, regardless of how the environment changes"
* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
binfmt_misc: add F option description to documentation
binfmt_misc: add persistent opened binary handler for containers
fs: add filp_clone_open API
Eryu Guan [Tue, 2 Aug 2016 11:58:28 +0000 (19:58 +0800)]
fs: return EPERM on immutable inode
In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.
So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Eryu Guan <guaneryu@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Aug 2016 14:01:14 +0000 (10:01 -0400)]
Merge branch 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
Linus Torvalds [Sat, 6 Aug 2016 13:50:36 +0000 (09:50 -0400)]
Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull more xfs updates from Dave Chinner:
"This is the second part of the XFS updates for this merge cycle, and
contains the new reverse block mapping feature for XFS.
Reverse mapping allows us to track the owner of a specific block on
disk precisely. It is implemented as a set of btrees (one per
allocation group) that track the owners of allocated extents.
Effectively it is a "used space tree" that is updated when we allocate
or free extents. i.e. it is coherent with the free space btrees we
already maintain and never overlaps with them.
This reverse mapping infrastructure is the building block of several
upcoming features - reflink, copy-on-write data, dedupe, online
metadata and data scrubbing, highly accurate bad sector/data loss
reporting to users, and significantly improved reconstruction of
damaged and corrupted filesystems. There's a lot of new stuff coming
along in the next couple of cycles,a nd it all builds in the rmap
infrastructure.
As such, it's a huge chunk of new code with new on-disk format
features and internal infrastructure. It warns at mount time as an
experimental feature and that it may eat data (as we do with all new
on-disk features until they stabilise). We have not released
userspace suport for it yet - userspace support currently requires
download from Darrick's xfsprogs repo and build from source, so the
access to this feature is really developer/tester only at this point.
Initial userspace support will be released at the same time kernel
with this code in it is released.
The new rmap enabled code regresses 3 xfstests - all are ENOSPC
related corner cases, one of which Darrick posted a fix for a few
hours ago. The other two are fixed by infrastructure that is part of
the upcoming reflink patchset. This new ENOSPC infrastructure
requires a on-disk format tweak required to keep mount times in
check - we need to keep an on-disk count of allocated rmapbt blocks so
we don't have to scan the entire btrees at mount time to count them.
This is currently being tested and will be part of the fixes sent in
the next week or two so users will not be exposed to this change"
* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
xfs: move (and rename) the deferred bmap-free tracepoints
xfs: collapse single use static functions
xfs: remove unnecessary parentheses from log redo item recovery functions
xfs: remove the extents array from the rmap update done log item
xfs: in btree_lshift, only allocate temporary cursor when needed
xfs: remove unnecesary lshift/rshift key initialization
xfs: remove the get*keys and update_keys btree ops pointers
xfs: enable the rmap btree functionality
xfs: don't update rmapbt when fixing agfl
xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
xfs: add rmap btree block detection to log recovery
xfs: add rmap btree geometry feature flag
xfs: propagate bmap updates to rmapbt
xfs: enable the xfs_defer mechanism to process rmaps to update
xfs: log rmap intent items
xfs: create rmap update intent log items
xfs: add rmap btree insert and delete helpers
xfs: convert unwritten status of reverse mappings
xfs: remove an extent from the rmap btree
xfs: add an extent to the rmap btree
...
Linus Torvalds [Sat, 6 Aug 2016 13:49:02 +0000 (09:49 -0400)]
Merge branch 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
Linus Torvalds [Sat, 6 Aug 2016 13:44:14 +0000 (09:44 -0400)]
Merge tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull mailcap fixlets from Mauro Carvalho Chehab:
"A small fixup for my and Shuah's entries in .mailcap.
Basically, those entries were with a syntax that makes
get_maintainer.pl to do the wrong thing"
* tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
.mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan
Linus Torvalds [Sat, 6 Aug 2016 13:20:13 +0000 (09:20 -0400)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
Linus Torvalds [Sat, 6 Aug 2016 13:18:21 +0000 (09:18 -0400)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
Linus Torvalds [Sat, 6 Aug 2016 13:13:11 +0000 (09:13 -0400)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
Linus Torvalds [Sat, 6 Aug 2016 13:04:35 +0000 (09:04 -0400)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two fixes and a cleanup-fix, to the syscall entry code and to ptrace"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/syscalls/64: Add compat_sys_keyctl for 32-bit userspace
x86/ptrace: Stop setting TS_COMPAT in ptrace code
x86/vdso: Error out if the vDSO isn't a valid DSO
Linus Torvalds [Sat, 6 Aug 2016 13:00:05 +0000 (09:00 -0400)]
Merge tag 'sh-for-4.8' of git://git.libc.org/linux-sh
Pull arch/sh updates from Rich Felker:
"These changes improve device tree support (including builtin DTB), add
support for the J-Core J2 processor, an open source synthesizable
reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
ABI mismatch issue, and fix various bugs including nommu-specific
issues and minor regressions introduced in 4.6.
The J-Core arch support is included here but to be usable it needs
drivers that are waiting on approval/inclusion from their subsystem
maintainers"
* tag 'sh-for-4.8' of git://git.libc.org/linux-sh: (23 commits)
sh: add device tree source for J2 FPGA on Mimas v2 board
sh: add defconfig for J-Core J2
sh: use common clock framework with device tree boards
sh: system call wire up
sh: Delete unnecessary checks before the function call "mempool_destroy"
sh: do not perform IPI-based cache flush except on boards that need it
sh: add SMP support for J2
sh: SMP support for SH2 entry.S
sh: add working futex atomic ops on userspace addresses for smp
sh: add J2 atomics using the cas.l instruction
sh: add AT_HWCAP flag for J-Core cas.l instruction
sh: add support for J-Core J2 processor
sh: fix build regression with CONFIG_OF && !CONFIG_OF_FLATTREE
sh: allow clocksource drivers to register sched_clock backends
sh: make heartbeat driver explicitly non-modular
sh: make board-secureedge5410 explicitly non-modular
sh: make mm/asids-debugfs explicitly non-modular
sh: make time.c explicitly non-modular
sh: fix futex/robust_list on nommu models
sh: disable aliased page logic on NOMMU models
...
Linus Torvalds [Sat, 6 Aug 2016 12:58:59 +0000 (08:58 -0400)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- avoid accessing unmapped FDT fields when checking validity
- correctly account for vDSO AUX entry in ARCH_DLINFO
- fix kallsyms with absolute expressions in linker script
- kill unnecessary symbol-based relocs in vmlinux
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix copy-on-write referencing in HugeTLB
arm64: mm: avoid fdt_check_header() before the FDT is fully mapped
arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
arm64: relocatable: suppress R_AARCH64_ABS64 relocations in vmlinux
arm64: vmlinux.lds: make __rela_offset and __dynsym_offset ABSOLUTE
Linus Torvalds [Sat, 6 Aug 2016 04:01:33 +0000 (00:01 -0400)]
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
Linus Torvalds [Sat, 6 Aug 2016 03:56:11 +0000 (23:56 -0400)]
Merge tag 'ntb-4.8' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"NTB bug fixes for the ntb_tool and ntb_perf, and improvements to the
ntb_perf and ntb_pingpong for increased debugability.
Also, modification to the ntb_transport layer to increase/decrease
the number of transport entries depending on the ring size"
* tag 'ntb-4.8' of git://github.com/jonmason/ntb:
NTB: ntb_hw_intel: use local variable pdev
NTB: ntb_hw_intel: show BAR size in debugfs info
ntb_test: Add a selftest script for the NTB subsystem
ntb_perf: clear link_is_up flag when the link goes down.
ntb_pingpong: Add a debugfs file to get the ping count
ntb_tool: Add link status and files to debugfs
ntb_tool: Postpone memory window initialization for the user
ntb_perf: Wait for link before running test
ntb_perf: Return results by reading the run file
ntb_perf: Improve thread handling to increase robustness
ntb_perf: Schedule based on time not on performance
ntb_transport: Check the number of spads the hardware supports
ntb_tool: Add memory window debug support
ntb_perf: Allow limiting the size of the memory windows
NTB: allocate number transport entries depending on size of ring size
ntb_tool: BUG: Ensure the buffer size is large enough to return all spads
ntb_tool: Fix infinite loop bug when writing spad/peer_spad file
Linus Torvalds [Sat, 6 Aug 2016 03:52:52 +0000 (23:52 -0400)]
Merge tag 'pstore-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
"Fixes for pstore ramoops driver to catch bad kfree() and to use better
DT bindings"
* tag 'pstore-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
ramoops: use persistent_ram_free() instead of kfree() for freeing prz
ramoops: use DT reserved-memory bindings
Linus Torvalds [Sat, 6 Aug 2016 03:47:27 +0000 (23:47 -0400)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is seven basic fixes (plus one MAINTAINER update) which came in
close to the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ipr: Fix error return code in ipr_probe_ioa()
fcoe: add missing destroy_workqueue() on error in fcoe_init()
lpfc: Fix possible NULL pointer dereference
fcoe: Use default VLAN for FIP VLAN discovery
ipr: Wait to do async scan until scsi host is initialized
MAINTAINERS: Update cxlflash maintainers
cxlflash: Verify problem state area is mapped before notifying shutdown
lpfc: fix oops in lpfc_sli4_scmd_to_wqidx_distr() from lpfc_send_taskmgmt()
Linus Torvalds [Sat, 6 Aug 2016 03:41:52 +0000 (23:41 -0400)]
Merge tag 'dm-4.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable dm-flakey fix to error read IO during the 'down_interval'
- a DM core suspend fix to establish the SUSPENDED flag before dropping
the SUSPENDING flag
- a blk-mq request-based DM (dm-mq) dm_stop_queue() fix to properly
stop the blk-mq hw_queues (and cancel pending requeue work); also
set/clear QUEUE_FLAG_STOPPED when stopping/starting the dm-mq
request_queue.
- a DM multipath fix to harden locking of in-core state flags in the
face of concurrent access while handling path failures under heavy
IO.
- a few small DM raid fixes to edge cases caught with further testing.
* tag 'dm-4.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: fix use of wrong status char during resynchronization
dm raid: constructor fails on non-zero incompat_features
dm raid: fix processing of max_recovery_rate constructor flag
dm: set DMF_SUSPENDED* _before_ clearing DMF_NOFLUSH_SUSPENDING
dm rq: fix the starting and stopping of blk-mq queues
dm mpath: add locking to multipath_resume and must_push_back
dm flakey: error READ bios during the down_interval
Linus Torvalds [Sat, 6 Aug 2016 03:31:51 +0000 (23:31 -0400)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Here's the second round of block updates for this merge window.
It's a mix of fixes for changes that went in previously in this round,
and fixes in general. This pull request contains:
- Fixes for loop from Christoph
- A bdi vs gendisk lifetime fix from Dan, worth two cookies.
- A blk-mq timeout fix, when on frozen queues. From Gabriel.
- Writeback fix from Jan, ensuring that __writeback_single_inode()
does the right thing.
- Fix for bio->bi_rw usage in f2fs from me.
- Error path deadlock fix in blk-mq sysfs registration from me.
- Floppy O_ACCMODE fix from Jiri.
- Fix to the new bio op methods from Mike.
One more followup will be coming here, ensuring that we don't
propagate the block types outside of block. That, and a rename of
bio->bi_rw is coming right after -rc1 is cut.
- Various little fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
mm/block: convert rw_page users to bio op use
loop: make do_req_filebacked more robust
loop: don't try to use AIO for discards
blk-mq: fix deadlock in blk_mq_register_disk() error path
Include: blkdev: Removed duplicate 'struct request;' declaration.
Fixup direct bi_rw modifiers
block: fix bdi vs gendisk lifetime mismatch
blk-mq: Allow timeouts to run while queue is freezing
nbd: fix race in ioctl
block: fix use-after-free in seq file
f2fs: drop bio->bi_rw manual assignment
block: add missing group association in bio-cloning functions
blkcg: kill unused field nr_undestroyed_grps
writeback: Write dirty times for WB_SYNC_ALL writeback
floppy: fix open(O_ACCMODE) for ioctl-only open
Linus Torvalds [Sat, 6 Aug 2016 03:29:05 +0000 (23:29 -0400)]
Merge tag 'acpi-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Two more fixes in ACPI drivers, one in the ACPI EC driver
(stable-candidate) and one in the ACPI button driver.
Specifics:
- An ACPI EC driver fix from the 4.3 cycle may cause the ACPICA's
method reentrancy limit to be exceeded for a _Qxx method due to a
large number of concurrent EC operations, so prevent that from
happening by moving the EC handling into a separate workqueue with
a limit on the number of concurrently executed work items (Lv
Zheng)
- Fix the cleanup code in the ACPI button driver that forgets to
clear two variables on exit which causes an error to occur on the
next attmpt to load the driver (Benjamin Tissoires)"
* tag 'acpi-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Work around method reentrancy limit in ACPICA for _Qxx
ACPI / button: remove pointer to old lid_sysfs on unbind
Linus Torvalds [Sat, 6 Aug 2016 03:26:16 +0000 (23:26 -0400)]
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
Linus Torvalds [Sat, 6 Aug 2016 03:24:15 +0000 (23:24 -0400)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
Linus Torvalds [Sat, 6 Aug 2016 03:07:43 +0000 (23:07 -0400)]
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB updates from Greg KH:
"Here are a few more straggler patches for USB for 4.8-rc1.
Most of these are for the usb-serial driver tree. All of those have
been in linux-next for a long time, but missed my previous pull
request to you.
The remaining change is to fix up a staging tree build error, due to
some USB gadget driver changes that went in. I put it in this tree as
it was for a USB driver and people are reporting the build error on
your tree.
All of these have been in linux-next for this week, and longer for the
usb-serial changes"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
staging: emxx_udc: allow modular build
USB: serial: use variable for status
USB: serial: option: add support for Telit LE910 PID 0x1206
USB: serial: cp210x: use kmemdup
USB: serial: ti_usb_3410_5052: use functions rather than macros
USB: serial: ti_usb_3410_5052: remove ti_usb_3410_5052.h
USB: serial: ti_usb_3410_5052: use __packed
USB: serial: ti_usb_3410_5052: remove useless comments
ramoops: use persistent_ram_free() instead of kfree() for freeing prz
persistent_ram_zone(=prz) structures are allocated by persistent_ram_new(),
which includes vmap() or ioremap(). But they are currently freed by
kfree(). This uses persistent_ram_free() for correct this asymmetry usage.
Instead of a ramoops-specific node, use a child node of /reserved-memory.
This requires that of_platform_device_create() be explicitly called
for the node, though, since "/reserved-memory" does not have its own
"compatible" property.
Suggested-by: Rob Herring <robh@kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Rob Herring <robh@kernel.org>
Michel Dänzer [Fri, 5 Aug 2016 09:36:10 +0000 (18:36 +0900)]
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
Fixes hangs under memory pressure, e.g. running the piglit test
tex3d-maxsize concurrently with other tests.
Fixes: 17d33bc9d6ef ("drm/ttm: drop waiting for idle in ttm_bo_evict.") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:12 +0000 (13:15 -0600)]
ntb_test: Add a selftest script for the NTB subsystem
This script automates testing doorbells, scratchpads and memory windows
for an NTB device. It can be run locally, with the NTB looped
back to the same host or use SSH to remotely control the second host.
In the single host case, the script just needs to be passed two
arguments: a PCI ID for each side of the link. In the two host case
the -r option must be used to specify the remote hostname (which must
be SSH accessible and should probably have ssh-keys exchanged).
A sample run looks like this:
$ sudo ./ntb_test.sh 0000:03:00.1 0000:83:00.1 -p 29
Starting ntb_tool tests...
Running link tests on: 0000:03:00.1 / 0000:83:00.1
Passed
Running link tests on: 0000:83:00.1 / 0000:03:00.1
Passed
Running db tests on: 0000:03:00.1 / 0000:83:00.1
Passed
Running db tests on: 0000:83:00.1 / 0000:03:00.1
Passed
Running spad tests on: 0000:03:00.1 / 0000:83:00.1
Passed
Running spad tests on: 0000:83:00.1 / 0000:03:00.1
Passed
Running mw0 tests on: 0000:03:00.1 / 0000:83:00.1
Passed
Running mw0 tests on: 0000:83:00.1 / 0000:03:00.1
Passed
Running mw1 tests on: 0000:03:00.1 / 0000:83:00.1
Passed
Running mw1 tests on: 0000:83:00.1 / 0000:03:00.1
Passed
Starting ntb_perf tests...
Running local perf test without DMA
0: copied 536870912 bytes in 164453 usecs, 3264 MBytes/s
Passed
Running remote perf test without DMA
0: copied 536870912 bytes in 164453 usecs, 3264 MBytes/s
Passed
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Shuah Khan <shuahkh@osg.samsung.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:13 +0000 (13:15 -0600)]
ntb_perf: clear link_is_up flag when the link goes down.
When the link goes down, the link_is_up flag did not return to
false. This could have caused some subtle corner case bugs
when the link goes up and down quickly.
Once that was fixed, there was found to be a race if the link was
brought down then immediately up. The link_cleanup work would
occasionally be scheduled after the next link up event. This would
cancel the link_work that was supposed to occur and leave ntb_perf
in an unusable state.
To fix this we get rid of the link_cleanup work and put the actions
directly in the link_down event.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:11 +0000 (13:15 -0600)]
ntb_pingpong: Add a debugfs file to get the ping count
This commit adds a debugfs 'count' file to ntb_pingpong. This is so
testing with ntb_pingpong can be automated beyond just checking the
logs for pong messages.
The count file returns a number which increments every pong. The
counter can be cleared by writing a zero.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:10 +0000 (13:15 -0600)]
ntb_tool: Add link status and files to debugfs
In order to more successfully script with ntb_tool it's useful to
have a link file to check the link status so that the script
doesn't use the other files until the link is up.
This commit adds a 'link' file to the debugfs directory which reads
boolean (Y or N) depending on the link status. Writing to the file
change the link state using ntb_link_enable or ntb_link_disable.
A 'link_event' file is also provided so an application can block until
the link changes to the desired state. If the user writes a 1, it will
block until the link is up. If the user writes a 0, it will block until
the link is down.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:09 +0000 (13:15 -0600)]
ntb_tool: Postpone memory window initialization for the user
In order to make the interface closer to the raw NTB API, this commit
changes memory windows so they are not initialized on link up.
Instead, the 'peer_trans*' debugfs files are introduced. When read,
they return information provided by ntb_mw_get_range. When written,
they create a buffer and initialize the memory window. The
value written is taken as the requested size of the buffer (which
is then rounded for alignment). Writing a value of zero frees the buffer
and tears down the memory window translation. The 'peer_mw*' file is
only created once the memory window translation is setup by the user.
Additionally, it was noticed that the read and write functions for the
'peer_mw*' files should have checked for a NULL pointer.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:06 +0000 (13:15 -0600)]
ntb_perf: Return results by reading the run file
Instead of having to watch logs, allow the results to be retrieved
by reading back the run file. This file will return "running" when
the test is running and nothing if no tests have been run yet.
It returns 1 line per thread, and will display an error message if the
corresponding thread returns an error.
With the above change, the pr_info calls that returned the results are
then changed to pr_debug calls.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:05 +0000 (13:15 -0600)]
ntb_perf: Improve thread handling to increase robustness
This commit accomplishes a few things:
1) Properly prevent multiple sets of threads from running at once using
a mutex. Lots of race issues existed with the thread_cleanup.
2) The mutex allows us to ensure that threads are finished before
tearing down the device or module.
3) Don't use kthread_stop when the threads can exit by themselves, as
this is counter-indicated by the kthread_create documentation. Threads
now wait for kthread_stop to occur.
4) Writing to the run file now blocks until the threads are complete.
The test can then be safely interrupted by a SIGINT.
Also, while I was at it:
5) debugfs_run_write shouldn't return 0 in the early check cases as this
could cause debugfs_run_write to loop undesirably.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:04 +0000 (13:15 -0600)]
ntb_perf: Schedule based on time not on performance
When debugging performance problems, if some issue causes the ntb
hardware to be significantly slower than expected, ntb_perf will
hang requiring a reboot because it only schedules once every 4GB.
Instead, schedule based on jiffies so it will not hang the CPU if
the transfer is slow.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Tue, 7 Jun 2016 17:20:22 +0000 (11:20 -0600)]
ntb_transport: Check the number of spads the hardware supports
I'm working on hardware that currently has a limited number of
scratchpad registers and ntb_ndev fails with no clue as to why. I
feel it is better to fail early and provide a reasonable error message
then to fail later on.
The same is done to ntb_perf, but it doesn't currently require enough
spads to actually fail. I've also removed the unused SPAD_MSG and
SPAD_ACK enums so that MAX_SPAD accurately reflects the number of
spads used.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Dave Jiang [Fri, 8 Apr 2016 17:49:06 +0000 (10:49 -0700)]
NTB: allocate number transport entries depending on size of ring size
Currently we only allocate a fixed default number of descriptors for the tx
and rx side. We should dynamically resize it to the number of descriptors
resides in the transport rings. We should know the number of transmit
descriptors at initializaiton. We will allocate the default number of
descriptors for receive side and allocate additional ones when we know the
actual max entries for receive.
Signed-off-by: Dave Jiang <dave.jiang@intel.com> Acked-by: Allen Hubbe <allen.hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Logan Gunthorpe [Mon, 20 Jun 2016 19:15:08 +0000 (13:15 -0600)]
ntb_tool: BUG: Ensure the buffer size is large enough to return all spads
On hardware with 32 scratchpad registers the spad field in ntb tool
could chop off the end. The maximum buffer size is increased from
256 to 15 times the number or scratchpads.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
This wasn't immediately obvious but 'pos' was not incrementing the
buffer, so after reading the second pair of values, 'pos' would once
again be 3 and it would re-read the second pair of values ad infinitum.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Acked-by: Allen Hubbe <Allen.Hubbe@emc.com> Signed-off-by: Jon Mason <jdmason@kudzu.us>
Linus Torvalds [Fri, 5 Aug 2016 13:48:22 +0000 (09:48 -0400)]
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
Linus Torvalds [Fri, 5 Aug 2016 13:45:14 +0000 (09:45 -0400)]
Merge tag 'sound-fix-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing existing here: as usual a few HD-audio fixes (device fixups, a
new AMD PCI ID, and a fix for krealloc() usage), in addition to a fix
in Kconfig for legacy arm drivers"
* tag 'sound-fix-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix headset mic detection problem for two dell machines
ALSA: hda: Fix krealloc() with __GFP_ZERO usage
ALSA: hda: add AMD Bonaire AZ PCI ID with proper driver caps
ALSA: arm: Fix empty menuconfig SND_ARM
ALSA: hda - On-board speaker fixup on ACER Veriton
ALSA: hda/realtek - Can't adjust speaker's volume on a Dell AIO
Linus Torvalds [Fri, 5 Aug 2016 13:00:54 +0000 (09:00 -0400)]
Merge tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
Linus Torvalds [Fri, 5 Aug 2016 12:58:00 +0000 (08:58 -0400)]
Merge tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture updates from James Hogan:
"Just a few minor fixes:
- Fix another incorrect inline asm register constraint, which has
been lying quietly for 5 and a half years before finally causing
build breakage during this merge window.
- Removal of duplicated KERN_INFO from Joe Perches
- Typo fixes from Andrea Gelmini"
* tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix __cmpxchg_u32 asm constraint for CMP
metag: Remove duplicate KERN_<LEVEL> prefix
metag: Fix typos
This defconfig is intended not to be specific to a particular board;
it enables drivers for all currently-supported hardware, and should be
updated to include additional drivers as they are added.
sh: use common clock framework with device tree boards
Enable common clk framework for DT-based boards and disable code that
depends on the legacy sh clk framework when common clk is enabled.
Once legacy drivers are converted over, the old code can be removed
entirely.
Rich Felker [Mon, 15 Feb 2016 18:36:13 +0000 (18:36 +0000)]
sh: add SMP support for J2
Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.
Rich Felker [Mon, 15 Feb 2016 18:32:31 +0000 (18:32 +0000)]
sh: SMP support for SH2 entry.S
The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.
sh: add AT_HWCAP flag for J-Core cas.l instruction
The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.
Rich Felker [Thu, 17 Mar 2016 23:09:37 +0000 (23:09 +0000)]
sh: add support for J-Core J2 processor
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.
Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.
No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
projects / kernel.git / log