Biju Das [Tue, 19 Apr 2022 14:24:53 +0000 (15:24 +0100)]
drm: bridge: adv7511: Enable DRM_BRIDGE_OP_HPD based on HPD interrupt
Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.
Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
Add bindings for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Rob Herring <robh+dt@kernel.org> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-1-marex@denx.de
Hsin-Yi Wang [Thu, 14 Apr 2022 09:00:04 +0000 (17:00 +0800)]
drm/bridge: anx7625: Fill in empty ELD when no connector
Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.
Devarsh Thakkar [Mon, 14 Mar 2022 11:37:39 +0000 (17:07 +0530)]
drm/tidss: Soft Reset DISPC on startup
Soft reset the display subsystem controller on startup and wait for
the reset to complete. This helps the scenario where display was
already in use by some other core before the linux was booted.
Paul Cercueil [Mon, 18 Apr 2022 19:44:36 +0000 (20:44 +0100)]
Merge drm/drm-next into drm-misc-next
drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Imre Deak [Mon, 11 Apr 2022 13:25:39 +0000 (16:25 +0300)]
drm/dp: Factor out a function to probe a DPCD address
Factor out from drm_dp_dpcd_read() a function to probe a DPCD address
with a 1-byte read access. This will be needed by the next patch doing a
read from an LTTPR address, which must happen without the preceding
wake-up read in drm_dp_dpcd_read().
While at it add tracing for the 1 byte read even if the read was
successful.
v2: Add a probe function instead of exporting drm_dp_dpcd_access(). (Jani)
v3: Add tracing for the 1-byte read even if the read was successful. (Khaled)
Jani Nikula [Mon, 11 Apr 2022 14:00:31 +0000 (17:00 +0300)]
drm/edid: use EDID block read helper in drm_do_get_edid()
Convert drm_do_get_edit() from the base block read helper to the generic
block read helper. There's quite a bit going on here, as the corrupt and
null EDID information is moved back to the caller. As we see, they were
not all that clear to begin with, and this change underlines that.
Jani Nikula [Mon, 11 Apr 2022 14:00:30 +0000 (17:00 +0300)]
drm/edid: abstract an EDID block read helper
We have an abstraction for the EDID base block read, yet duplicating the
retries and error handling for extension block reads. Introduce a more
generic EDID block read helper.
Switch to the helper piecemeal, starting with drm_edid_get_panel_id(),
which doesn't need or have access to the connector anyway.
The subtle change is switching from drm_edid_block_valid() to
edid_block_check(). We also status print once, not for every attempt.
Dave Airlie [Thu, 14 Apr 2022 02:03:08 +0000 (12:03 +1000)]
Merge tag 'drm-intel-next-2022-04-13-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
drm/i915 feature pull for v5.19:
Features and functionality:
- Add support for new Tile 4 format on DG2 (Stan)
- Add support for new CCS clear color compression on DG2 (Mika, Juha-Pekka)
- Add support for new render and media compression formats on DG2 (Matt)
- Support multiple eDP and LVDS native mode refresh rates (Ville)
- Support static DRRS (Ville)
- ATS-M platform info (Matt)
- RPL-S PCI IDs (Tejas)
- Extend DP HDR support to HSW+ (Uma)
- Bump ADL-P DMC version to v2.16 (Madhumitha)
- Let users disable PSR2 while enabling PSR1 (José)
Refactoring and cleanups:
- Massive DRRS and panel fixed mode refactoring and cleanups (Ville)
- Power well refactoring and cleanup (Imre)
- Clean up and refactor crtc readout and compute config (Ville)
- Use kernel string helpers (Lucas)
- Refactor gmbus pin lookups and allocation (Jani)
- PCH display cleanups (Ville)
- DPLL and DPLL manager refactoring (Ville)
- Include and header refactoring (Jani, Tvrtko)
- DMC abstractions (Jani)
- Non-x86 build refactoring (Casey)
- VBT parsing refactoring (Ville)
- Bigjoiner refactoring (Ville)
- Optimize plane, pfit, scaler, etc. programming using unlocked writes (Ville)
- Split several register writes in commit to noarm+arm pairs (Ville)
- Clean up SAGV handling (Ville)
- Clean up bandwidth and ddb allocation (Ville)
- FBC cleanups (Ville)
Fixes:
- Fix native HDMI and DP HDMI DFP clock limits on deep color/4:2:0 (Ville)
- Fix DMC firmware platform check (Lucas)
- Fix cursor coordinates on bigjoiner secondary (Ville)
- Fix MSO vs. bigjoiner timing confusion (Ville)
- Fix ADL-P eDP voltage swing (José)
- Fix VRR capability property update (Manasi)
- Log DG2 SNPS PHY calibration errors (Matt, Lucas)
- Fix PCODE request status checks (Stan)
- Fix uncore unclaimed access warnings (Lucas)
- Fix VBT new max TMDS clock parsing (Shawn)
- Fix ADL-P non-existent underrun recovery (Swathi Dhanavanthri)
- Fix ADL-N stepping info (Tejas)
- Fix DPT mapping flags to contiguous (Stan)
- Fix DG2 max display bandwidth (Vinod)
- Fix DP low voltage SKU checks (Ankit)
- Fix RPL-S VT-d translation enable via quirk (Tejas)
- Fixes to PSR2 (José)
- Fix PIPE_MBUS_DBOX_CTL programming (José)
- Fix LTTPR capability read/check on DP 1.2 (Imre)
- Fix ADL-P register corruption after DDI clock enabling (Imre)
- Fix ADL-P MBUS DBOX BW and B credits (Caz)
Daniel Vetter [Wed, 13 Apr 2022 08:21:28 +0000 (10:21 +0200)]
fbcon: Fix delayed takeover locking
I messed up the delayed takover path in the locking conversion in 0627f2704a33 ("fbcon: Move console_lock for register/unlink/unregister").
If CONFIG_FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER is enabled, fbcon take-over
doesn't take place when calling fbcon_fb_registered(). Instead, is deferred
using a workqueue and its fbcon_register_existing_fbs() function calls to
fbcon_fb_registered() again for each registered fbcon fb.
This leads to the console_lock tried to be held twice, causing a deadlock.
Fix it by re-extracting the lockless function and using it in the
delayed takeover path, where we need to hold the lock already to
iterate over the list of already registered fb. Well the current code
still is broken in there (since the list is protected by a
registration_lock, which we can't take here because it nests the other
way round with console_lock), but in the future this will be a list
protected by console_lock when this is all sorted out.
While reviewing the broken commit I realized that I've left some
outdated comments about the locking behind. Fix those too.
v2: Improve commit message (Javier)
Reported-by: Nathan Chancellor <nathan@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Cc: Nathan Chancellor <nathan@kernel.org> Fixes: 0627f2704a33 ("fbcon: Move console_lock for register/unlink/unregister") Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Du Cheng <ducheng2@gmail.com> Cc: Claudio Suarez <cssk@net-c.es> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Matthew Wilcox <willy@infradead.org> Cc: Zheyu Ma <zheyuma97@gmail.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Helge Deller <deller@gmx.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220413082128.348186-1-daniel.vetter@ffwll.ch
Marek Vasut [Fri, 1 Apr 2022 16:21:54 +0000 (18:21 +0200)]
drm/panel: lvds: Use bus_flags from DT panel-timing property
This driver currently rewrites bus_flags based solely on the value of
DT property 'data-mirror' and ignores bus_flags which might have been
set in DT panel-timing node. Specificaly, the 'de-active' DT property
sets DRM_BUS_FLAG_DE_ bus_flags.
Since of_get_drm_panel_display_mode() conveniently parses the bus_flags
out of DT panel-timing property, just ORR them with bus_flags inferred
from 'data-mirror' DT property and use the result as panel bus_flags.
This fixes handling of panels with 'panel-timing { de-active = <1>; };'.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dmitry Osipenko <digetx@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20220401162154.295152-2-marex@denx.de
Marek Vasut [Fri, 1 Apr 2022 16:21:53 +0000 (18:21 +0200)]
drm/panel: lvds: Simplify mode parsing
The mode parsing is currently implemented in three steps:
of_get_display_timing() - DT panel-timing to struct display_timing
videomode_from_timing() - struct display_timing to struct videomode
drm_display_mode_from_videomode() - struct videomode to struct drm_display_mode
Replace all that with simple of_get_drm_panel_display_mode() call,
which already populates struct drm_display_mode and then duplicate
that mode in panel_lvds_get_modes() each time, since the mode does
not change.
Nice bonus is the bus_flags parsed by of_get_drm_panel_display_mode()
out of panel-timing DT node, which is used in subsequent patch to fix
handling of 'de-active' DT property.
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dmitry Osipenko <digetx@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220401162154.295152-1-marex@denx.de
Marek Vasut [Sun, 3 Apr 2022 17:10:04 +0000 (19:10 +0200)]
drm: bridge: icn6211: Convert to regmap
To make debugging easier, convert driver to regmap. Implement read and write
regmap tables for known registers, keep all known register readable and mark
those which are obviously read-only as not writeable.
Use common I2C regmap for the I2C configuration, implement custom regmap bus
for DSI configuration. The later is mandatory as this chip requires one extra
byte set to read access length between register address and data.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Mark Brown <broonie@kernel.org> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org Acked-by: Mark Brown <broonie@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220403171004.368464-1-marex@denx.de
Ville Syrjälä [Tue, 15 Mar 2022 14:00:00 +0000 (16:00 +0200)]
drm/i915/fbc: Introduce intel_fbc_sanitize()
Let's make sure FBC is always disabled when we start to take
over the hardware state.
I suspect this should never really happen, since the only time
when we really should be taking over with the display already
active is when the previous state was progammed by the BIOS,
which likely shouldn't use FBC. This could be driver init,
or S4 resume when the boot kernel doesn't load i915. But I
suppose no harm in keeping this code around for exra safety
since it's quite trivial.
Ville Syrjälä [Tue, 15 Mar 2022 13:59:59 +0000 (15:59 +0200)]
drm/i915/fbc: Remove intel_fbc_global_disable()
By the time intel_fbc_global_disable() gets called during driver
teardown we should have already disabled all the crtcs, so
no way FBC should be enabled at this point.
And I have no idea what the other user (i915_restore_display())
is even trying to achieve.
So let's just throw intel_fbc_global_disable() into the bin.
Ville Syrjälä [Tue, 15 Mar 2022 13:59:57 +0000 (15:59 +0200)]
drm/i915/fbc: Skip nuke when flip is pending
Don't issue a nuke from frontbuffer flush while a flip is pending.
This avoids the DSPADDR/DSPSURF rmw abuse from the pre-snb nuke
from racing with the DSPADDR/DSPSURF write being performed by
the flip/plane update. The flip itself will already cause the nuke
so a double nuke is redundant.
Ville Syrjälä [Tue, 15 Mar 2022 13:59:55 +0000 (15:59 +0200)]
drm/i915/fbc: Eliminate possible_framebuffer_bits
Not sure what the point of this fbc->possible_frontbuffer_bits is.
And especially don't see why it's returning all the bits when
fbc is not even enabled. So let's just get rid of this and only
say we are interested in the plane's frontbuffer bits when fbc
is actually enabled.
Matthew Auld [Wed, 13 Apr 2022 08:21:33 +0000 (09:21 +0100)]
drm/ttm: fixup ttm_bo_add_move_fence v2
It looks like we still need to call dma_fence_put() on the man->move,
otherwise we just end up leaking it, leading to fireworks later.
v2(Daniel):
- Simplify the function tail
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5689 Fixes: 3b93dce4dd40 ("drm/ttm: remove bo->moving") Cc: Christian König <christian.koenig@amd.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220413082133.272445-1-matthew.auld@intel.com
Manasi Navare [Thu, 3 Mar 2022 23:32:22 +0000 (15:32 -0800)]
drm/i915/display/vrr: Reset VRR capable property on a long hpd
With some VRR panels, user can turn VRR ON/OFF on the fly from the panel settings.
When VRR is turned OFF ,sends a long HPD to the driver clearing the Ignore MSA bit
in the DPCD. Currently the driver parses that onevery HPD but fails to reset
the corresponding VRR Capable Connector property.
Hence the userspace still sees this as VRR Capable panel which is incorrect.
Fix this by explicitly resetting the connector property.
v2: Reset vrr capable if status == connector_disconnected
v3: Use i915 and use bool vrr_capable (Jani Nikula)
v4: Move vrr_capable to after update modes call (Jani N)
Remove the redundant comment (Jan N)
v5: Fixes the regression on older platforms by resetting the VRR
only if HAS_VRR
v6: Remove the checks from driver, add in drm core before
setting VRR prop (Ville)
v7: Move VRR set/reset to set/unset_edid (Ville)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: f10fa7204344 ("drm/i915/display/vrr: Reset VRR capable property on a long hpd") Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220303233222.4698-1-manasi.d.navare@intel.com
Matthew Auld [Mon, 11 Apr 2022 08:56:03 +0000 (09:56 +0100)]
drm/ttm: stop passing NULL fence in ttm_bo_move_sync_cleanup
If we hit the sync case, like when skipping clearing for kernel internal
objects, or when falling back to cpu clearing, like in i915, we end up
trying to add a NULL fence, but with some recent changes in this area
this now just results in NULL deref in dma_resv_add_fence:
In the ttm_bo_move_sync_cleanup() case it seems we only really care
about calling ttm_bo_wait_free_node(), so let's instead just call that
directly.
Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Christian König <christian.koenig@amd.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Nirmoy Das <nirmoy.das@linux.intel.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220411085603.58156-1-matthew.auld@intel.com
drm/i915/dg2: Add support for DG2 clear color compression
Add support for the DG2 specific render compression with clear color
framebuffer format.
DG2 onwards discrete gfx has support for new flat CCS mapping,
which brings in display feature in to avoid Aux walk for compressed
surface. This support build on top of Flat CCS support added in XEHPSDV.
FLAT CCS surface base address should be 64k aligned,
Compressed displayable surfaces must use tile4 format.
Mika Kahola [Mon, 11 Apr 2022 14:34:04 +0000 (17:34 +0300)]
drm/fourcc: Introduce format modifier for DG2 clear color
DG2 clear color render compression uses Tile4 layout. Therefore, we need
to define a new format modifier for uAPI to support clear color rendering.
v2:
Display version is fixed. [Imre]
KDoc is enhanced for cc modifier. [Nanley & Lionel]
v3:
Split out the modifier addition to a separate patch.
Clarify the modifier layout description.
Matt Roper [Mon, 11 Apr 2022 14:34:03 +0000 (17:34 +0300)]
drm/i915/dg2: Add support for DG2 render and media compression
Add support for DG2 render and media compression, for the description of
buffer layouts see the previous patch adding the corresponding
frame buffer modifiers.
v2:
Display version fix [Imre]
v3:
Split out modifier addition to separate patch.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com>
cc: Anshuman Gupta <anshuman.gupta@intel.com> Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com> Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220411143405.1073845-3-imre.deak@intel.com
Matt Roper [Mon, 11 Apr 2022 14:34:02 +0000 (17:34 +0300)]
drm/fourcc: Introduce format modifiers for DG2 render and media compression
The render/media engines on DG2 unify render compression and media
compression into a single format for the first time, using the Tile 4
layout for main surfaces. The compression algorithm is different from
any previous platform and the display engine must still be configured to
decompress either a render or media compressed surface; as such, we
need new RC and MC framebuffer modifiers to represent buffers in this
format.
Dave Airlie [Tue, 12 Apr 2022 07:39:45 +0000 (17:39 +1000)]
Merge tag 'drm-misc-next-2022-04-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.19:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- atomic: Add atomic_print_state to private objects
- edid: Constify the EDID parsing API, rework of the API
- dma-buf: Add dma_resv_replace_fences, dma_resv_get_singleton, make
dma_resv_excl_fence private
- format: Support monochrome formats
- fbdev: fixes for cfb_imageblit and sys_imageblit, pagelist
corruption fix
- selftests: several small fixes
- ttm: Rework bulk move handling
Driver Changes:
- Switch all relevant drivers to drm_mode_copy or drm_mode_duplicate
- bridge: conversions to devm_drm_of_get_bridge and panel_bridge,
autosuspend for analogix_dp, audio support for it66121, DSI to DPI
support for tc358767, PLL fixes and I2C support for icn6211
- bridge_connector: Enable HPD if supported
- etnaviv: fencing improvements
- gma500: GEM and GTT improvements, connector handling fixes
- komeda: switch to plane reset helper
- mediatek: MIPI DSI improvements
- omapdrm: GEM improvements
- panel: DT bindings fixes for st7735r, few fixes for ssd130x, new
panels: ltk035c5444t, B133UAN01, NV3052C
- qxl: Allow to run on arm64
- sysfb: Kconfig rework, support for VESA graphic mode selection
- vc4: Add a tracepoint for CL submissions, HDMI YUV output,
HDMI and clock improvements
- virtio: Remove restriction of non-zero blob_flags,
- vmwgfx: support for CursorMob and CursorBypass 4, various
improvements and small fixes
Ville Syrjälä [Fri, 18 Feb 2022 10:04:03 +0000 (12:04 +0200)]
drm: Use drm_mode_copy()
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
Ville Syrjälä [Fri, 18 Feb 2022 10:04:02 +0000 (12:04 +0200)]
drm: Use drm_mode_init() for on-stack modes
Initialize on-stack modes with drm_mode_init() to guarantee
no stack garbage in the list head, or that we aren't copying
over another mode's list head.
Based on the following cocci script, with manual fixups:
@decl@
identifier M;
expression E;
@@
- struct drm_display_mode M = E;
+ struct drm_display_mode M;
@@
identifier decl.M;
expression decl.E;
statement S, S1;
@@
struct drm_display_mode M;
... when != S
+ drm_mode_init(&M, &E);
+
S1
Ville Syrjälä [Tue, 5 Apr 2022 17:33:54 +0000 (20:33 +0300)]
drm/i915/bios: Validate the panel_name table
In addition to the fp_timing,dvo_timing,panel_pnp_id tables
there also exists a panel_name table. Unlike the others this
is just one offset+table_size even though there are still 16
actual panel_names in the data block.
The panel_name table made its first appearance somewhere
around VBT version 156-163. The exact version is not known.
But we don't need to know that since we can just check whether
the pointers block has enough room for it or not.
Ville Syrjälä [Tue, 5 Apr 2022 17:33:51 +0000 (20:33 +0300)]
drm/i915/bios: Use the copy of the LFP data table always
Currently get_lvds_fp_timing() still returns a pointer to the original
data block rather than our copy. Let's convert the data pointer offsets
to be relative to the data block rather than the whole BDB. With that
we can make get_lvds_fp_timing() return a pointer to the copy.
Ville Syrjälä [Wed, 6 Apr 2022 13:38:17 +0000 (16:38 +0300)]
drm/i915/bios: Make copies of VBT data blocks
Make a copy of each VBT data block with a guaranteed minimum
size. The extra (if any) will just be left zeroed.
This means we don't have to worry about going out of bounds
when accessing any of the structure members. Otherwise that
could easliy happen if we simply get the version check wrong,
or if the VBT is broken/malicious.
v2: Don't do arithmetic between bdb header and copy
of the LFP data block (Jani)
v3: Make all the copies up front
v4: Only WARN about min_size==0 if we found the block
Ville Syrjälä [Tue, 5 Apr 2022 17:33:49 +0000 (20:33 +0300)]
drm/i915/bios: Use the cached BDB version
We have the BDB version cached, use it. We're going to have to
start doing some of the BDB block parsing later, at which point
we may no longer have the VBT around anymore (we free it at the
end of intel_bios_init() when it didn't come via OpRegion).
Lucas De Marchi [Sun, 10 Apr 2022 06:15:36 +0000 (23:15 -0700)]
drm/i915/dg2: Do not explode on phy calibration error
When the PHY fails on calibration we were previously skipping the ddi
initialization. However the driver is not really prepared for that,
ultimately leading to a NULL pointer dereference:
[ 75.748348] i915 0000:03:00.0: [drm:intel_modeset_init_nogem [i915]] SNPS PHY A failed to calibrate; output will not be used.
...
[ 75.750336] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled
...
We skip the initialization of PHY A, but later we try to find out what
is the phy for that power well and dereference dig_port, which is NULL.
Failing the PHY calibration could be left as a warning or error, like it
was before commit bde9210c231d ("drm/i915/dg2: Skip output init on PHY
calibration failure"). However that often fails for outputs not being
used, which would make the warning/error appear on systems that have no
visible issues. Anyway, there is still a need to fix those failures,
but that is left for later.
Liviu Dudau [Thu, 2 Dec 2021 17:00:33 +0000 (17:00 +0000)]
drm/komeda: return early if drm_universal_plane_init() fails.
If drm_universal_plane_init() fails early we jump to the common cleanup code
that calls komeda_plane_destroy() which in turn could access the uninitalised
drm_plane and crash. Return early if an error is detected without going through
the common code.
Zhou Qingyang [Wed, 1 Dec 2021 03:37:03 +0000 (11:37 +0800)]
drm/komeda: Fix an undefined behavior bug in komeda_plane_add()
In komeda_plane_add(), komeda_get_layer_fourcc_list() is assigned to
formats and used in drm_universal_plane_init().
drm_universal_plane_init() passes formats to
__drm_universal_plane_init(). __drm_universal_plane_init() further
passes formats to memcpy() as src parameter, which could lead to an
undefined behavior bug on failure of komeda_get_layer_fourcc_list().
Fix this bug by adding a check of formats.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_KOMEDA=m show no new warnings,
and our static analyzer no longer warns about this code.
Paul Boddie [Thu, 7 Apr 2022 11:16:11 +0000 (13:16 +0200)]
drm/ingenic: Add dw-hdmi driver specialization for jz4780
A specialisation of the generic Synopsys HDMI driver is employed for
JZ4780 HDMI support. This requires a new driver, plus device tree and
configuration modifications.
Here we add Kconfig DRM_INGENIC_DW_HDMI, Makefile and driver code.
Note that there is no hpd-gpio installed on the CI20 board HDMI
connector. Hence there is no hpd detection by the connector driver
and we have to enable polling in the dw-hdmi core driver.
For that we need to set .poll_enabled but that struct component
can only be accessed by core code. Hence we use the public
setter function drm_kms_helper_hotplug_event() introduced before.
Also note that we disable Color Space Conversion since it is not
working on jz4780.
The .atomic_get_input_bus_fmts() callback of our top bridge should
return the possible input formats for a given output format. If the
requested output format is not supported, then NULL should be returned,
otherwise the bus format negociation will end with a bus format that the
encoder does not support.
drm/i915: Swap ret and status returned from skl_pcode_request
If ret isn't zero, it is almost for sure ETIMEDOUT, because
we use it in wait_for macro which does continuous retries
until timeout is reached. If we still ran out of time and
retries, we most likely would be interested in getting status,
to understand what was the actual error propagated from PCode,
rather than to find out that we had a time out, which is anyway
quite obvious, if the function fails.
v2: Make it status ? status : ret(thanks Vinod for the hint)
Currently skl_pcode_try_request function doesn't
properly handle return value it gets from
snb_pcode_rw, but treats status != 0 as success,
returning true, which basically doesn't allow
to use retry/timeout mechanisms if PCode happens
to be busy and returns EGAIN or some other status
code not equal to 0.
We saw this on real hw and also tried simulating this
by always returning -EAGAIN from snb_pcode_rw for 6 times, which
currently will just result in false success, while it should
have tried until timeout is reached:
We see en error because higher level api, still notices that status was wrong,
however we still did try only once.
We fix it by requiring _both_ the status to be 0 and
request/reply match for success(true) and function
should return failure(false) if either status turns
out to be EAGAIN, EBUSY or whatever or reply/request
masks do not match.
Add a simple check to reject any size not aligned to the
min_page_size.
when size is not aligned to min_page_size, driver module
should handle in their own way either to round_up() the
size value to min_page_size or just to enable WARN_ON().
If we dont handle the alignment properly, we may hit the
following bug, Unigine Heaven has allocation requests for
example required pages are 257 and alignment request is 256.
To allocate the left over 1 page, continues the iteration to
find the order value which is 0 and when it compares with
min_order = 8, triggers the BUG_ON(order < min_order).
v2: add more commit description
v3: remove WARN_ON()
Merge tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"This is a single serial driver fix for a build issue that showed up
due to changes that came in through the tty tree in 5.18-rc1 that were
missed previously. It resolves a build error with the mpc52xx_uart
driver.
It has been in linux-next this week with no reported problems"
* tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned, part II.
Merge tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.18-rc2 that resolves an
endian issue for the r8188eu driver. It has been in linux-next all
this week with no reported problems"
* tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix PPPoE tag insertion on little endian systems
Merge tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are two small driver core changes for 5.18-rc2.
They are the final bits in the removal of the default_attrs field in
struct kobj_type. I had to wait until after 5.18-rc1 for all of the
changes to do this came in through different development trees, and
then one new user snuck in. So this series has two changes:
- removal of the default_attrs field in the powerpc/pseries/vas code.
The change has been acked by the PPC maintainers to come through
this tree
- removal of default_attrs from struct kobj_type now that all
in-kernel users are removed.
This cleans up the kobject code a little bit and removes some
duplicated functionality that confused people (now there is only
one way to do default groups)
Both of these have been in linux-next for all of this week with no
reported problems"
* tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: kobj_type: remove default_attrs
powerpc/pseries/vas: use default_groups in kobj_type
Merge tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"A single driver fix. It resolves the build warning issue on 32bit
systems in the habannalabs driver that came in during the 5.18-rc1
merge cycle.
It has been in linux-next for all this week with no reported problems"
* tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: Fix test build failures
Merge tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix KVM "lost kick" race, where an attempt to pull a vcpu out of the
guest could be lost (or delayed until the next guest exit).
- Disable SCV (system call vectored) when PR KVM guests could be run.
- Fix KVM PR guests using SCV, by disallowing AIL != 0 for KVM PR
guests.
- Add a new KVM CAP to indicate if AIL == 3 is supported.
- Fix a regression when hotplugging a CPU to a memoryless/cpuless node.
- Make virt_addr_valid() stricter for 64-bit Book3E & 32-bit, which
fixes crashes seen due to hardened usercopy.
- Revert a change to max_mapnr which broke HIGHMEM.
Thanks to Christophe Leroy, Fabiano Rosas, Kefeng Wang, Nicholas Piggin,
and Srikar Dronamraju.
* tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc: Set max_mapnr correctly"
powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
KVM: PPC: Move kvmhv_on_pseries() into kvm_ppc.h
powerpc/numa: Handle partially initialized numa nodes
powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
KVM: PPC: Use KVM_CAP_PPC_AIL_MODE_3
KVM: PPC: Book3S PR: Disallow AIL != 0
KVM: PPC: Book3S PR: Disable SCV when AIL could be disabled
KVM: PPC: Book3S HV P9: Fix "lost kick" race
Merge tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of interrupt chip driver fixes:
- A fix for a long standing bug in the ARM GICv3 redistributor
polling which uses the wrong bit number to test.
- Prevent translation of bogus ACPI table entries which map device
interrupts into the IPI space on ARM GICs.
- Don't write into the pending register of ARM GICV4 before the scan
in hardware has completed.
- A set of build and correctness fixes for the Qualcomm MPM driver"
* tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic, gic-v3: Prevent GSI to SGI translations
irqchip/gic-v3: Fix GICR_CTLR.RWP polling
irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
irqchip/irq-qcom-mpm: fix return value check in qcom_mpm_init()
irq/qcom-mpm: Fix build error without MAILBOX
Merge tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- A couple of fixes to cgroup-related handling of perf events
- A couple of fixes to event encoding on Sapphire Rapids
- Pass event caps of inherited events so that perf doesn't fail wrongly
at fork()
- Add support for a new Raptor Lake CPU
* tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Always set cpuctx cgrp when enable cgroup event
perf/core: Fix perf_cgroup_switch()
perf/core: Use perf_cgroup_info->active to check if cgroup is active
perf/core: Don't pass task around when ctx sched in
perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
perf/x86/intel: Don't extend the pseudo-encoding to GP counters
perf/core: Inherit event_caps
perf/x86/uncore: Add Raptor Lake uncore support
perf/x86/msr: Add Raptor Lake CPU support
perf/x86/cstate: Add Raptor Lake support
perf/x86: Add Intel Raptor Lake support
Merge tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Allow the compiler to optimize away unused percpu accesses and change
the local_lock_* macros back to inline functions
- A couple of fixes to static call insn patching
* tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "mm/page_alloc: mark pagesets as __maybe_unused"
Revert "locking/local_lock: Make the empty local_lock_*() function a macro."
x86/percpu: Remove volatile from arch_raw_cpu_ptr().
static_call: Remove __DEFINE_STATIC_CALL macro
static_call: Properly initialise DEFINE_STATIC_CALL_RET0()
static_call: Don't make __static_call_return0 static
x86,static_call: Fix __static_call_return0 for i386
Merge tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Use the correct static key checking primitive on the IRQ exit path
- Two fixes for the new forceidle balancer
* tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Fix compile error in dynamic_irqentry_exit_cond_resched()
sched: Teach the forced-newidle balancer about CPU affinity limitation.
sched/core: Fix forceidle balancing
Merge tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix the clang command line option probing and remove some options to
filter out, fixing the build with the latest clang versions
- Fix 'perf bench' futex and epoll benchmarks to deal with machines
with more than 1K CPUs
- Fix 'perf test tsc' error message when not supported
- Remap perf ring buffer if there is no space for event, fixing perf
usage in 32-bit ChromeOS
- Drop objdump stderr to avoid getting stuck waiting for stdout output
in 'perf annotate'
- Fix up garbled output by now showing unwind error messages when
augmenting frame in best effort mode
- Fix perf's libperf_print callback, use the va_args eprintf() variant
- Sync vhost and arm64 cputype headers with the kernel sources
- Fix 'perf report --mem-mode' with ARM SPE
- Add missing external commands ('iiostat', etc) to 'perf --list-cmds'
* tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf annotate: Drop objdump stderr to avoid getting stuck waiting for stdout output
perf tools: Add external commands to list-cmds
perf docs: Add perf-iostat link to manpages
perf session: Remap buf if there is no space for event
perf bench: Fix epoll bench to correct usage of affinity for machines with #CPUs > 1K
perf bench: Fix futex bench to correct usage of affinity for machines with #CPUs > 1K
perf tools: Fix perf's libperf_print callback
perf: arm-spe: Fix perf report --mem-mode
perf unwind: Don't show unwind error messages when augmenting frame pointer stack
tools headers arm64: Sync arm64's cputype.h with the kernel sources
perf test tsc: Fix error message when not supported
perf build: Don't use -ffat-lto-objects in the python feature test when building with clang-13
perf python: Fix probing for some clang command line options
tools build: Filter out options and warnings not supported by clang
tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
tools include UAPI: Sync linux/vhost.h with the kernel sources
Merge tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull cxl and nvdimm fixes from Dan Williams:
- Fix a compile error in the nvdimm unit tests
- Fix a shadowed variable warning in the CXL PCI driver
* tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
cxl/pci: Drop shadowed variable
tools/testing/nvdimm: Fix security_init() symbol collision
Merge tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a race condition with consumers accessing the fields of GPIO IRQ
chips before they're fully initialized
* tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: Restrict usage of GPIO chip irq members before initialization
Ian Rogers [Thu, 7 Apr 2022 23:04:59 +0000 (16:04 -0700)]
perf annotate: Drop objdump stderr to avoid getting stuck waiting for stdout output
If objdump writes to stderr it can block waiting for it to be read. As
perf doesn't read stderr then progress stops with perf waiting for
stdout output.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexandre Truong <alexandre.truong@arm.com> Cc: Dave Marchevsky <davemarchevsky@fb.com> Cc: Denis Nikitin <denik@chromium.org> Cc: German Gomez <german.gomez@arm.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.garry@huawei.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Lexi Shao <shaolexi@huawei.com> Cc: Li Huafei <lihuafei1@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Martin Liška <mliska@suse.cz> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Cc: Remi Bernon <rbernon@codeweavers.com> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Richter <tmricht@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Cc: William Cohen <wcohen@redhat.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20220407230503.1265036-2-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Michael Petlan [Mon, 4 Apr 2022 22:15:41 +0000 (00:15 +0200)]
perf tools: Add external commands to list-cmds
The `perf --list-cmds` output prints only internal commands, although
there is no reason for that from users' perspective.
Adding the external commands to commands array with NULL function
pointer allows printing all perf commands while not changing the logic
of command handler selection.
Lucas De Marchi [Fri, 8 Apr 2022 16:48:37 +0000 (09:48 -0700)]
drm/i915/uncore: Warn only if unclaimed access remains flagged
Commit 04c5c969052f ("drm/i915/uncore: Warn on previous unclaimed
accesses") tried to improve our report of unclaimed register access,
however it unveiled cases that were not previously causing any harm.
Downgrade the first message to debug so we can still see them and
eventually fix, but don't warn.
perf bench: Fix epoll bench to correct usage of affinity for machines with #CPUs > 1K
The 'perf bench epoll' testcase fails on systems with more than 1K CPUs.
Testcase: perf bench epoll all
Result snippet:
<<>>
Run summary [PID 106497]: 1399 threads monitoring on 64 file-descriptors for 8 secs.
perf: pthread_create: No such file or directory
<<>>
In epoll benchmarks (ctl, wait) pthread_create is invoked in do_threads
from respective bench_epoll_* function. Though the logs shows direct
failure from pthread_create, the actual failure is from
"sched_setaffinity" returning EINVAL (invalid argument).
This happens because the default mask size in glibc is 1024. To overcome
this 1024 CPUs mask size limitation of cpu_set_t, change the mask size
using the CPU_*_S macros.
Patch addresses this by fixing all the epoll benchmarks to use CPU_ALLOC
to allocate cpumask, CPU_ALLOC_SIZE for size, and CPU_SET_S to set the
mask.
perf: pthread_create: No such file or directory
<<>>
All the futex benchmarks (ie hash, lock-api, requeue, wake,
wake-parallel), pthread_create is invoked in respective bench_futex_*
function. Though the logs shows direct failure from pthread_create,
strace logs showed that actual failure is from "sched_setaffinity"
returning EINVAL (invalid argument).
This happens because the default mask size in glibc is 1024. To overcome
this 1024 CPUs mask size limitation of cpu_set_t, change the mask size
using the CPU_*_S macros.
Patch addresses this by fixing all the futex benchmarks to use CPU_ALLOC
to allocate cpumask, CPU_ALLOC_SIZE for size, and CPU_SET_S to set the
mask.
James Clark [Fri, 8 Apr 2022 14:40:56 +0000 (15:40 +0100)]
perf: arm-spe: Fix perf report --mem-mode
Since commit 2fc3249501090d83 ("perf report: Bail out --mem-mode if mem
info is not available") "perf mem report" and "perf report --mem-mode"
don't allow opening the file unless one of the events has
PERF_SAMPLE_DATA_SRC set.
SPE doesn't have this set even though synthetic memory data is generated
after it is decoded. Fix this issue by setting DATA_SRC on SPE events.
This has no effect on the data collected because the SPE driver doesn't
do anything with that flag and doesn't generate samples.
Fixes: 2fc3249501090d83 ("perf report: Bail out --mem-mode if mem info is not available") Signed-off-by: James Clark <james.clark@arm.com> Tested-by: Leo Yan <leo.yan@linaro.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: German Gomez <german.gomez@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Garry <john.garry@huawei.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: linux-arm-kernel@lists.infradead.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20220408144056.1955535-1-james.clark@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
James Clark [Wed, 6 Apr 2022 14:56:51 +0000 (15:56 +0100)]
perf unwind: Don't show unwind error messages when augmenting frame pointer stack
Commit Fixes: 4a37737374048d9c ("perf arm64: Inject missing frames when
using 'perf record --call-graph=fp'") intended to add a 'best effort'
DWARF unwind that improved the frame pointer stack in most scenarios.
It's expected that the unwind will fail sometimes, but this shouldn't be
reported as an error. It only works when the return address can be
determined from the contents of the link register alone.
Fix the error shown when the unwinder requires extra registers by adding
a new flag that suppresses error messages. This flag is not set in the
normal --call-graph=dwarf unwind mode so that behavior is not changed.
Fixes: 4a37737374048d9c ("perf arm64: Inject missing frames when using 'perf record --call-graph=fp'") Reported-by: John Garry <john.garry@huawei.com> Signed-off-by: James Clark <james.clark@arm.com> Tested-by: John Garry <john.garry@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexandre Truong <alexandre.truong@arm.com> Cc: German Gomez <german.gomez@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20220406145651.1392529-1-james.clark@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers arm64: Sync arm64's cputype.h with the kernel sources
To get the changes in:
38db5a505b92e85e ("arm64: Add part number for Arm Cortex-A78AE")
That addresses this perf build warning:
Warning: Kernel ABI header at 'tools/arch/arm64/include/asm/cputype.h' differs from latest version at 'arch/arm64/include/asm/cputype.h'
diff -u tools/arch/arm64/include/asm/cputype.h arch/arm64/include/asm/cputype.h
Cc: Ali Saidi <alisaidi@amazon.com> Cc: Andrew Kilroy <andrew.kilroy@arm.com> Cc: Chanho Park <chanho61.park@samsung.com> Cc: German Gomez <german.gomez@arm.com> Cc: James Clark <james.clark@arm.com> Cc: John Garry <john.garry@huawei.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Will Deacon <will@kernel.org> Link: http://lore.kernel.org/lkml/ Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Chengdong Li [Fri, 8 Apr 2022 08:47:48 +0000 (16:47 +0800)]
perf test tsc: Fix error message when not supported
By default `perf test tsc` does not return the error message when the
child process detected kernel does not support it. Instead, the child
process prints an error message to stderr, unfortunately stderr is
redirected to /dev/null when verbose <= 0.
This patch does:
- return TEST_SKIP to the parent process instead of TEST_OK when
perf_read_tsc_conversion() is not supported.
- Add a new subtest of testing if TSC is supported on current
architecture by moving exist code to a separate function.
It avoids two places in test__perf_time_to_tsc() that return
TEST_SKIP by doing this.
- Extend the test suite definition to contain above two subtests.
Current test_suite and test_case structs do not support printing skip
reason when the number of subtest less than 1. To print skip reason, it
is necessary to extend current test suite definition.
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chengdong Li <chengdongli@tencent.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: likexu@tencent.com Link: https://lore.kernel.org/r/20220408084748.43707-1-chengdongli@tencent.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf build: Don't use -ffat-lto-objects in the python feature test when building with clang-13
Using -ffat-lto-objects in the python feature test when building with
clang-13 results in:
clang-13: error: optimization flag '-ffat-lto-objects' is not supported [-Werror,-Wignored-optimization-argument]
error: command '/usr/sbin/clang' failed with exit code 1
cp: cannot stat '/tmp/build/perf/python_ext_build/lib/perf*.so': No such file or directory
make[2]: *** [Makefile.perf:639: /tmp/build/perf/python/perf.so] Error 1
Noticed when building on a docker.io/library/archlinux:base container.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Fangrui Song <maskray@google.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Keeping <john@metanate.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf python: Fix probing for some clang command line options
The clang compiler complains about some options even without a source
file being available, while others require one, so use the simple
tools/build/feature/test-hello.c file.
Then check for the "is not supported" string in its output, in addition
to the "unknown argument" already being looked for.
This was noticed when building with clang-13 where -ffat-lto-objects
isn't supported and since we were looking just for "unknown argument"
and not providing a source code to clang, was mistakenly assumed as
being available and not being filtered to set of command line options
provided to clang, leading to a build failure.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Fangrui Song <maskray@google.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Keeping <john@metanate.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Sedat Dilek <sedat.dilek@gmail.com> Link: http://lore.kernel.org/lkml/ Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools build: Filter out options and warnings not supported by clang
These make the feature check fail when using clang, so remove them just
like is done in tools/perf/Makefile.config to build perf itself.
Adding -Wno-compound-token-split-by-macro to tools/perf/Makefile.config
when building with clang is also necessary to avoid these warnings
turned into errors (-Werror):
CC /tmp/build/perf/util/scripting-engines/trace-event-perl.o
In file included from util/scripting-engines/trace-event-perl.c:35:
In file included from /usr/lib64/perl5/CORE/perl.h:4085:
In file included from /usr/lib64/perl5/CORE/hv.h:659:
In file included from /usr/lib64/perl5/CORE/hv_func.h:34:
In file included from /usr/lib64/perl5/CORE/sbox32_hash.h:4:
/usr/lib64/perl5/CORE/zaphod32_hash.h:150:5: error: '(' and '{' tokens introducing statement expression appear in different macro expansion contexts [-Werror,-Wcompound-token-split-by-macro]
ZAPHOD32_SCRAMBLE32(state[0],0x9fade23b);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/lib64/perl5/CORE/zaphod32_hash.h:80:38: note: expanded from macro 'ZAPHOD32_SCRAMBLE32'
#define ZAPHOD32_SCRAMBLE32(v,prime) STMT_START { \
^~~~~~~~~~
/usr/lib64/perl5/CORE/perl.h:737:29: note: expanded from macro 'STMT_START'
# define STMT_START (void)( /* gcc supports "({ STATEMENTS; })" */
^
/usr/lib64/perl5/CORE/zaphod32_hash.h:150:5: note: '{' token is here
ZAPHOD32_SCRAMBLE32(state[0],0x9fade23b);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/lib64/perl5/CORE/zaphod32_hash.h:80:49: note: expanded from macro 'ZAPHOD32_SCRAMBLE32'
#define ZAPHOD32_SCRAMBLE32(v,prime) STMT_START { \
^
/usr/lib64/perl5/CORE/zaphod32_hash.h:150:5: error: '}' and ')' tokens terminating statement expression appear in different macro expansion contexts [-Werror,-Wcompound-token-split-by-macro]
ZAPHOD32_SCRAMBLE32(state[0],0x9fade23b);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/lib64/perl5/CORE/zaphod32_hash.h:87:41: note: expanded from macro 'ZAPHOD32_SCRAMBLE32'
v ^= (v>>23); \
^
/usr/lib64/perl5/CORE/zaphod32_hash.h:150:5: note: ')' token is here
ZAPHOD32_SCRAMBLE32(state[0],0x9fade23b);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/usr/lib64/perl5/CORE/zaphod32_hash.h:88:3: note: expanded from macro 'ZAPHOD32_SCRAMBLE32'
} STMT_END
^~~~~~~~
/usr/lib64/perl5/CORE/perl.h:738:21: note: expanded from macro 'STMT_END'
# define STMT_END )
^
Please refer to the discussion on the Link: tag below, where Nathan
clarifies the situation:
<quote>
acme> And then get to the problems at the end of this message, which seem
acme> similar to the problem described here:
acme>
acme> From Nathan Chancellor <>
acme> Subject [PATCH] mwifiex: Remove unnecessary braces from HostCmd_SET_SEQ_NO_BSS_INFO
acme>
acme> https://lkml.org/lkml/2020/9/1/135
acme>
acme> So perhaps in this case its better to disable that
acme> -Werror,-Wcompound-token-split-by-macro when building with clang?
Yes, I think that is probably the best solution. As far as I can tell,
at least in this file and context, the warning appears harmless, as the
"create a GNU C statement expression from two different macros" is very
much intentional, based on the presence of PERL_USE_GCC_BRACE_GROUPS.
The warning is fixed in upstream Perl by just avoiding creating GNU C
statement expressions using STMT_START and STMT_END:
If I am reading the source code correctly, an alternative to disabling
the warning would be specifying -DPERL_GCC_BRACE_GROUPS_FORBIDDEN but it
seems like that might end up impacting more than just this site,
according to the issue discussion above.
</quote>
Based-on-a-patch-by: Sedat Dilek <sedat.dilek@gmail.com> Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # Debian/Selfmade LLVM-14 (x86-64) Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Fangrui Song <maskray@google.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Keeping <john@metanate.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Link: http://lore.kernel.org/lkml/YkxWcYzph5pC1EK8@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools include UAPI: Sync linux/vhost.h with the kernel sources
To get the changes in:
6555b38122fe3d0a ("vdpa: support exposing the count of vqs to userspace") 1163db6bffe2c8cf ("vdpa: support exposing the config size to userspace")
Silencing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/vhost.h' differs from latest version at 'include/uapi/linux/vhost.h'
diff -u tools/include/uapi/linux/vhost.h include/uapi/linux/vhost.h
$ diff -u tools/include/uapi/linux/vhost.h include/uapi/linux/vhost.h
--- tools/include/uapi/linux/vhost.h 2021-07-15 16:17:01.840818309 -0300
+++ include/uapi/linux/vhost.h 2022-04-02 18:55:05.702522387 -0300
@@ -150,4 +150,11 @@
/* Get the valid iova range */
#define VHOST_VDPA_GET_IOVA_RANGE _IOR(VHOST_VIRTIO, 0x78, \
struct vhost_vdpa_iova_range)
+
+/* Get the config size */
+#define VHOST_VDPA_GET_CONFIG_SIZE _IOR(VHOST_VIRTIO, 0x79, __u32)
+
+/* Get the count of all virtqueues */
+#define VHOST_VDPA_GET_VQS_COUNT _IOR(VHOST_VIRTIO, 0x80, __u32)
+
#endif
$ tools/perf/trace/beauty/vhost_virtio_ioctl.sh > before
$ cp include/uapi/linux/vhost.h tools/include/uapi/linux/vhost.h
$ tools/perf/trace/beauty/vhost_virtio_ioctl.sh > after
$ diff -u before after
--- before 2022-04-04 14:52:25.036375145 -0300
+++ after 2022-04-04 14:52:31.906549976 -0300
@@ -38,4 +38,6 @@
[0x73] = "VDPA_GET_CONFIG",
[0x76] = "VDPA_GET_VRING_NUM",
[0x78] = "VDPA_GET_IOVA_RANGE",
+ [0x79] = "VDPA_GET_CONFIG_SIZE",
+ [0x80] = "VDPA_GET_VQS_COUNT",
};
$
projects / kernel.git / log