This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.
It seems the SPI fifo must have room for 2 bursts when the dma_tx_req
signal is generated or it might skip some words. This in turn makes
the rx dma channel never complete for bi-directional transfers.
Fix it by setting tx burst length to fifo_len / 4 and the dma
watermark to fifo_len / 2.
However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in
the case of access SPI and UART at byte or halfword size, DMAC only
support fixed-address burst and the address must be aligned to word."
So this relies on fifo_len being a multiple of 16 such that the
burst length (= fifo_len / 4) is a multiple of 4 and the addresses
will be word-aligned.
Fixes: dcfc861d24ec ("spi: rockchip: adjust dma watermark and burstlen") Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Sat, 23 Feb 2019 08:49:48 +0000 (08:49 +0000)]
spi: core: allow defining time that cs is deasserted
For some SPI devices that support speed_hz > 1MHz the default 10 us delay
when cs_change = 1 is typically way to long and may result in poor spi bus
utilization.
This patch makes it possible to control the delay at micro or nano second
resolution on a per spi_transfer basis. It even allows an "as fast as
possible" mode with:
xfer.cs_change_delay_unit = SPI_DELAY_UNIT_NSECS;
xfer.cs_change_delay = 0;
The delay code is shared between delay_usecs and cs_change_delay for
consistency and reuse, so in the future this change_delay_unit could also
apply to delay_usec as well.
Note that on slower SOCs/CPU actually reaching ns deasserts on cs is not
realistic as the gpio overhead alone (without any delays added ) may
already leave cs deasserted for more than 1us - at least on a raspberry pi.
But at the very least this way we can keep it as short as possible.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Tue, 23 Apr 2019 20:15:13 +0000 (20:15 +0000)]
spi: bcm2835: add driver stats to debugfs
To estimate efficiency add statistics on transfer types
(polling, interrupt and dma) used to debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions
fixed compile issue when CONFIG_DEBUG_FS is unset Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Tue, 23 Apr 2019 20:15:11 +0000 (20:15 +0000)]
spi: bcm2835: make the polling duration limits configurable
Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.
So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)
This replicates similar code found in spi-bcm2835aux.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Tue, 23 Apr 2019 20:15:10 +0000 (20:15 +0000)]
spi: bcm2835: added comment about different bus behaviour of DMA mode
The DMA mode behaves slightly different than polling or interrupt driven
mode, so just document the fact
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
new in V2 Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Sperl [Tue, 23 Apr 2019 20:15:09 +0000 (20:15 +0000)]
spi: bcm2835: Avoid 64-bit arithmetic in xfer len calc
Avoid 64 bit aritmetics when deciding if we need to use polling or not
This replicates: commit d704afffe65c
("spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc")
from spi-bcm2835aux
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unnecessary argument of xfer_time_us when calling
bcm2835_spi_transfer_one_poll.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
reorganized patchset
added extra rational, descriptions Signed-off-by: Mark Brown <broonie@kernel.org>
Radu Pirea [Sun, 5 May 2019 18:06:46 +0000 (21:06 +0300)]
spi: at91-usart: add DMA support
This patch adds support for DMA. Transfers are done with dma only if
they are longer than 16 bytes in order to achieve a better performance.
DMA setup introduces a little overhead and for transfers shorter than 16
bytes there is no performance improvement.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro> Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Fri, 3 May 2019 23:18:29 +0000 (01:18 +0200)]
spi: ep93xx: Drop unused variable
My previous patch leaves a dangling variable in the driver.
get rid of it.
Fixes: 06a391b1621e ("spi: ep93xx: Convert to use CS GPIO descriptors") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: rspi: Fix handling of QSPI code when transmit and receive
Process handling QSPI when transmit/receive at qspi_trigger_transfer_out_in() as follows:
Setting the trigger, is the number of bytes in the FIFO buffer to determine
when there is an interrupt. Then check if the value of triggering number is
32-bytes or 1-byte, there will be corresponding processing
Handling (if (n == QSPI_BUFFER_SIZE) esle) this is unnecessary, leads to the
same processing of data transmission or reception, The difference here are with
ret = rspi_wait_for_tx_empty(rspi);
ret = rspi_wait_for_rx_full(rspi);
When the nummber trigger is 32 bytes, we only write into FIFO when the FIFO is completely empty
(interrupt transmission), and only receive if FIFO is full of 32 bytes of data.
In the case of a nummber trigger that is 1 byte, in principle we still need to process
rspi_wait_for_tx_empty/full so that FIFO is empty only with the amount of data we need to write to
or equal to the number of bytes we need to receive, There is currently no processing of this.
And in the current case with this patch, at this time it only needs at least 1 byte received in
FIFO that has interrupt received, or FIFO at least 1bytes free can be written into FIFO,
This patch therefore does not affect this processing.
So we need to eliminate unnecessary waste processing (if (n == QSPI_BUFFER_SIZE) esle),
more precisely in waiting for FIFO status.
The same with handling in qspi_transfer_out()/qspi_transfer_in().
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp> Signed-off-by: Mark Brown <broonie@kernel.org>
atmel_qspi objects are kept in spi_controller objects, so, first get
pointer to spi_controller object and then get atmel_qspi object from
spi_controller object.
Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.
When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.
For example, with:
- ssp_clk = 50 MHz
- dev freq = 15 MHz
without this patch the SSP clock will be greater than 15 MHz:
- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others
Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select
When GPIO chip-select is used nothing prevents any available SPI
controllers to work with both CS-high and traditional CS-low modes.
In fact the SPI bus core code already does it, so we don't need to
introduce any modification there. But spi_setup() still fails to
switch the interface settings if CS-high flag is set for the case
of GPIO-driven slave chip-select when the SPI controller doesn't
support the hardwired CS-inversion. Lets fix it by clearing the
SPI_CS_HIGH flag out from bad_bits (unsupported by controller) when
client chip is selected by GPIO.
This feature is useful for slave devices, which in accordance with
communication protocol can work with both active-high and active-low
chip-selects. I am aware of one such device. It is MMC-SPI interface,
when at init sequence the driver needs to perform a read operation with
low and high chip-select sequentially (requirement of 74 clock cycles
with both chipselect, see the mmc_spi driver for details).
Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.
EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Daniel Gomez [Mon, 22 Apr 2019 19:12:33 +0000 (21:12 +0200)]
spi: AD ASoC: declare missing of table
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias: spi:adau1979
alias: spi:adau1978
alias: spi:adau1977
After this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias: of:N*T*Cadi,adau1979C*
alias: of:N*T*Cadi,adau1979
alias: of:N*T*Cadi,adau1978C*
alias: of:N*T*Cadi,adau1978
alias: of:N*T*Cadi,adau1977C*
alias: of:N*T*Cadi,adau1977
alias: spi:adau1979
alias: spi:adau1978
alias: spi:adau1977
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl
Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Split spi transfers into chunks of <=65532 to enable the driver to
perform DMA transfer on big buffers. The DLEN register specifies the
number of bytes to transfer in DMA mode. It is 16-bit wide and thus the
maximum DMA transfer is 65535 bytes. Set the maximum to 65532 (4 byte
aligned) since the FIFO in DMA mode is accessed in 4 byte chunks.
->max_dma_len is the value the spi core uses when splitting the buffer
into scatter gather entries.
The BCM2835 DMA block has 2 types of channels/engines:
- Normal: Max length: 1G
- Lite: Max length: 65535
Even when using a Lite channel we will not exceed the max length, so
let's drop setting ->max_dma_len.
Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com> Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Leilk Liu [Wed, 17 Apr 2019 08:47:16 +0000 (16:47 +0800)]
dt-bindings: spi: spi-mt65xx: add support for MT8516
Add binding documentation of spi-mt65xx for MT8516 SOC.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Evan Green [Tue, 16 Apr 2019 03:27:43 +0000 (20:27 -0700)]
spi: pxa2xx: Add support for Intel Comet Lake
Add PCI IDs for SPI on Comet Lake.
Signed-off-by: Evan Green <evgreen@chromium.org> Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Large transfers (64kB) doesn't show up in the trace. Not sure why, but
since printk can only display buffers up to 64 bytes in length, we only
need to store the first 64 bytes.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
spi_split_transfers_maxsize() can be used to split a transfer. This
function uses spi_res to lifetime manage the added transfer structures.
So in order to finalize the current message while it contains the split
transfers, spi_res_release() must be called after finalizing.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Fri, 12 Apr 2019 13:25:51 +0000 (16:25 +0300)]
spi: Remove one needless transfer speed fall back case
Falling back to maximum speed of the controller in case of SPI slave
maximum speed is not set is needless. It already defaults to maximum
speed of the controller since commit 052eb2d49006 ("spi: core: Set
max_speed_hz of spi_device default to max_speed_hz of controller").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-mem: Fix build error without CONFIG_SPI_MEM
When building with CONFIG_SPI_MEM is not set
gc warns this:
drivers/spi/spi-zynq-qspi.o: In function `zynq_qspi_supports_op':
spi-zynq-qspi.c:(.text+0x1da): undefined reference to `spi_mem_default_supports_op'
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix EFI decompressor entry (ensuring barrier instructions are
enabled prior to use)"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache
ARM: 8856/1: NOMMU: Fix CCR register faulty initialization when MPU is disabled
ARM: fix function graph tracer and unwinder dependencies
Merge tag 'powerpc-5.1-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A one-liner to make our Radix MMU support depend on HUGETLB_PAGE. We
use some of the hugetlb inlines (eg. pud_huge()) when operating on the
linear mapping and if they're compiled into empty wrappers we can
corrupt memory.
Then two fixes to our VFIO IOMMU code. The first is not a regression
but fixes the locking to avoid a user-triggerable deadlock.
The second does fix a regression since rc1, and depends on the first
fix. It makes it possible to run guests with large amounts of memory
again (~256GB).
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.1-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm_iommu: Allow pinning large regions
powerpc/mm_iommu: Fix potential deadlock
powerpc/mm/radix: Make Radix require HUGETLB_PAGE
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"One core bug fix and a few driver ones
- FRWR memory registration for hfi1/qib didn't work with with some
iovas causing a NFSoRDMA failure regression due to a fix in the NFS
side
- A command flow error in mlx5 allowed user space to send a corrupt
command (and also smash the kernel stack we've since learned)
- Fix a regression and some bugs with device hot unplug that was
discovered while reviewing Andrea's patches
- hns has a failure if the user asks for certain QP configurations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Bugfix for mapping user db
RDMA/ucontext: Fix regression with disassociate
RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages
RDMA/mlx5: Do not allow the user to write to the clock page
IB/mlx5: Fix scatter to CQE in DCT QP creation
IB/rdmavt: Fix frwr memory registration
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups for Synaptics RMI4 driver and allowing
snvs_pwrkey to be selected on more boards"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - write config register values to the right offset
Input: synaptics-rmi4 - fix possible double free
Input: snvs_pwrkey - make it depend on ARCH_MXC
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- Fix an early boot crash in the RSDP parsing code by effectively
turning off the parsing call - we ran out of time but want to fix the
regression. The more involved fix is being worked on.
- Fix a crash that can trigger in the kmemlek code.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix a crash with kmemleak_scan()
x86/boot: Disable RSDP parsing temporarily
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"A cstate event enumeration fix for Kaby/Coffee Lake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Update KBL Package C-state events to also include PC8/PC9/PC10 counters
for the error handling path, and rather than complicate that code, just
make it ok to always free what was returned by the init function.
That's what the code used to do before commit 4ab42d78e37a ("ppp, slip:
Validate VJ compression slot parameters completely") when slhc_init()
just returned NULL for the error case, with no actual indication of the
details of the error.
Reported-by: syzbot+45474c076a4927533d2e@syzkaller.appspotmail.com Fixes: 4ab42d78e37a ("ppp, slip: Validate VJ compression slot parameters completely") Acked-by: Ben Hutchings <ben@decadent.org.uk> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
fs/proc/proc_sysctl.c: Fix a NULL pointer dereference
mm/page_alloc.c: fix never set ALLOC_NOFRAGMENT flag
mm/page_alloc.c: avoid potential NULL pointer dereference
mm, page_alloc: always use a captured page regardless of compaction result
mm: do not boost watermarks to avoid fragmentation for the DISCONTIG memory model
lib/test_vmalloc.c: do not create cpumask_t variable on stack
lib/Kconfig.debug: fix build error without CONFIG_BLOCK
zram: pass down the bvec we need to read into in the work struct
mm/memory_hotplug.c: drop memory device reference after find_memory_block()
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- keep the tail of an unaligned initrd reserved
- adjust ftrace_make_call() to deal with the relative nature of PLTs
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/module: ftrace: deal with place relative nature of PLTs
arm64: mm: Ensure tail of unaligned initrd is reserved
Merge tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:
- Use "nosteal" for ring buffer splice pages
- Memory leak fix in error path of trace_pid_write()
- Fix preempt_enable_no_resched() (use preempt_enable()) in ring
buffer code"
* tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
trace: Fix preempt_enable_no_resched() abuse
tracing: Fix a memory leak by early error exit in trace_pid_write()
tracing: Fix buffer_ref pipe ops
Merge tag 'gpio-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Not much to say about them, regular fixes:
- Fix a bug on the errorpath of gpiochip_add_data_with_key()
- IRQ type setting on the spreadtrum GPIO driver"
* tag 'gpio-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: Fix gpiochip_add_data_with_key() error path
gpio: eic: sprd: Fix incorrect irq type setting for the sync EIC
Merge tag 'drm-fixes-2019-04-26' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular drm fixes, nothing too outstanding, I'm guessing Easter was
slowing people down.
i915:
- FEC enable fix
- BXT display lanes fix
ttm:
- fix reinit for reloading drivers regression
imx:
- DP CSC fix
sun4i:
- module unload/load fix
vc4:
- memory leak fix
- compile fix
dw-hdmi:
- rockchip scdc overflow fix
sched:
- docs fix
vmwgfx:
- dma api layering fix"
* tag 'drm-fixes-2019-04-26' of git://anongit.freedesktop.org/drm/drm:
drm/bridge: dw-hdmi: fix SCDC configuration for ddc-i2c-bus
drm/vmwgfx: Fix dma API layer violation
drm/vc4: Fix compilation error reported by kbuild test bot
drm/sun4i: Unbind components before releasing DRM and memory
drm/vc4: Fix memory leak during gpu reset.
drm/sched: Fix description of drm_sched_stop
drm/imx: don't skip DP channel disable for background plane
gpu: ipu-v3: dp: fix CSC handling
drm/ttm: fix re-init of global structures
drm/sun4i: Fix component unbinding and component master deletion
drm/sun4i: Set device driver data at bind time for use in unbind
drm/sun4i: Add missing drm_atomic_helper_shutdown at driver unbind
drm/i915: Restore correct bxt_ddi_phy_calc_lane_lat_optim_mask() calculation
drm/i915: Do not enable FEC without DSC
drm: bridge: dw-hdmi: Fix overflow workaround for Rockchip SoCs
Merge tag 'for-5.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One patch to fix a crash in io submission path, due to memory
allocation errors.
In short, the multipage bio work that landed in 5.1 caused larger bios
that in turn require larger temporary memory for checksums. The patch
is a workaround, we're going to rework the allocation so it does not
require the vmalloc fallback.
It took a while to identify that it's caused by patches in 5.1 and not
a patchset that did some changes in error handling in the code. I've
tested it on various memory/cpu combinations, it could hit OOM but
does not crash.
The timestamp of the patch is less than a day due to updates in the
changelog, tests were running meanwhile"
* tag 'for-5.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Switch memory allocations in async csum calculation path to kvmalloc
Merge tag '5.1-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three small SMB3 fixes (all for stable as well): two leaks and a
rename bug"
* tag '5.1-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix page reference leak with readv/writev
cifs: do not attempt cifs operation on smb2+ rename error
cifs: fix memory leak in SMB2_read
commit 23da9588037e ("fs/proc/proc_sysctl.c: fix NULL pointer
dereference in put_links") forgot to handle start_unregistering() case,
while header->parent is NULL, it calls erase_header() and as seen in the
above syzkaller call trace, accessing &header->parent->root will trigger
a NULL pointer dereference.
As that commit explained, there is also no need to call
start_unregistering() if header->parent is NULL.
Link: http://lkml.kernel.org/r/20190409153622.28112-1-yuehaibing@huawei.com Fixes: 23da9588037e ("fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links") Fixes: 0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/page_alloc.c: fix never set ALLOC_NOFRAGMENT flag
Commit 0a79cdad5eb2 ("mm: use alloc_flags to record if kswapd can wake")
removed setting of the ALLOC_NOFRAGMENT flag. Bring it back.
The runtime effect is that ALLOC_NOFRAGMENT behaviour is restored so
that allocations are spread across local zones to avoid fragmentation
due to mixing pageblocks as long as possible.
Link: http://lkml.kernel.org/r/20190423120806.3503-2-aryabinin@virtuozzo.com Fixes: 0a79cdad5eb2 ("mm: use alloc_flags to record if kswapd can wake") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ac.preferred_zoneref->zone passed to alloc_flags_nofragment() can be NULL.
'zone' pointer unconditionally derefernced in alloc_flags_nofragment().
Bail out on NULL zone to avoid potential crash. Currently we don't see
any crashes only because alloc_flags_nofragment() has another bug which
allows compiler to optimize away all accesses to 'zone'.
Link: http://lkml.kernel.org/r/20190423120806.3503-1-aryabinin@virtuozzo.com Fixes: 6bb154504f8b ("mm, page_alloc: spread allocations across zones before introducing fragmentation") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm, page_alloc: always use a captured page regardless of compaction result
During the development of commit 5e1f0f098b46 ("mm, compaction: capture
a page under direct compaction"), a paranoid check was added to ensure
that if a captured page was available after compaction that it was
consistent with the final state of compaction. The intent was to catch
serious programming bugs such as using a stale page pointer and causing
corruption problems.
However, it is possible to get a captured page even if compaction was
unsuccessful if an interrupt triggered and happened to free pages in
interrupt context that got merged into a suitable high-order page. It's
highly unlikely but Li Wang did report the following warning on s390
occuring when testing OOM handling. Note that the warning is slightly
edited for clarity.
This patch simply removes the check entirely instead of trying to be
clever about pages freed from interrupt context. If a serious
programming error was introduced, it is highly likely to be caught by
prep_new_page() instead.
Link: http://lkml.kernel.org/r/20190419085133.GH18914@techsingularity.net Fixes: 5e1f0f098b46 ("mm, compaction: capture a page under direct compaction") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: Li Wang <liwang@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: do not boost watermarks to avoid fragmentation for the DISCONTIG memory model
Mikulas Patocka reported that commit 1c30844d2dfe ("mm: reclaim small
amounts of memory when an external fragmentation event occurs") "broke"
memory management on parisc.
The machine is not NUMA but the DISCONTIG model creates three pgdats
even though it's a UMA machine for the following ranges
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000000100000000 End 0x00000001bfdfffff Size 3070 MB
2) Start 0x0000004040000000 End 0x00000040ffffffff Size 3072 MB
Mikulas reported:
With the patch 1c30844d2, the kernel will incorrectly reclaim the
first zone when it fills up, ignoring the fact that there are two
completely free zones. Basiscally, it limits cache size to 1GiB.
For example, if I run:
# dd if=/dev/sda of=/dev/null bs=1M count=2048
- with the proper kernel, there should be "Buffers - 2GiB"
when this command finishes. With the patch 1c30844d2, buffers
will consume just 1GiB or slightly more, because the kernel was
incorrectly reclaiming them.
The page allocator and reclaim makes assumptions that pgdats really
represent NUMA nodes and zones represent ranges and makes decisions on
that basis. Watermark boosting for small pgdats leads to unexpected
results even though this would have behaved reasonably on SPARSEMEM.
DISCONTIG is essentially deprecated and even parisc plans to move to
SPARSEMEM so there is no need to be fancy, this patch simply disables
watermark boosting by default on DISCONTIGMEM.
Link: http://lkml.kernel.org/r/20190419094335.GJ18914@techsingularity.net Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: Mikulas Patocka <mpatocka@redhat.com> Tested-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: James Bottomley <James.Bottomley@hansenpartnership.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/Kconfig.debug: fix build error without CONFIG_BLOCK
If CONFIG_TEST_KMOD is set to M, while CONFIG_BLOCK is not set, XFS and
BTRFS can not be compiled successly.
Link: http://lkml.kernel.org/r/20190410075434.35220-1-yuehaibing@huawei.com Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram: pass down the bvec we need to read into in the work struct
When scheduling work item to read page we need to pass down the proper
bvec struct which points to the page to read into. Before this patch it
uses a randomly initialized bvec (only if PAGE_SIZE != 4096) which is
wrong.
Note that without this patch on arch/kernel where PAGE_SIZE != 4096
userspace could read random memory through a zram block device (thought
userspace probably would have no control on the address being read).
mm/memory_hotplug.c: drop memory device reference after find_memory_block()
Right now we are using find_memory_block() to get the node id for the
pfn range to online. We are missing to drop a reference to the memory
block device. While the device still gets unregistered via
device_unregister(), resulting in no user visible problem, the device is
never released via device_release(), resulting in a memory leak. Fix
that by properly using a put_device().
Link: http://lkml.kernel.org/r/20190411110955.1430-1-david@redhat.com Fixes: d0dc12e86b31 ("mm/memory_hotplug: optimize memory hotplug") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Pankaj Gupta <pagupta@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Qian Cai <cai@lca.pw> Cc: Arun KS <arunks@codeaurora.org> Cc: Mathieu Malaterre <malat@debian.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Tue, 23 Apr 2019 20:03:18 +0000 (22:03 +0200)]
trace: Fix preempt_enable_no_resched() abuse
Unless the very next line is schedule(), or implies it, one must not use
preempt_enable_no_resched(). It can cause a preemption to go missing and
thereby cause arbitrary delays, breaking the PREEMPT=y invariant.
Link: http://lkml.kernel.org/r/20190423200318.GY14281@hirez.programming.kicks-ass.net Cc: Waiman Long <longman@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: the arch/x86 maintainers <x86@kernel.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: huang ying <huang.ying.caritas@gmail.com> Cc: Roman Gushchin <guro@fb.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: stable@vger.kernel.org Fixes: 2c2d7329d8af ("tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Wenwen Wang [Sat, 20 Apr 2019 02:22:59 +0000 (21:22 -0500)]
tracing: Fix a memory leak by early error exit in trace_pid_write()
In trace_pid_write(), the buffer for trace parser is allocated through
kmalloc() in trace_parser_get_init(). Later on, after the buffer is used,
it is then freed through kfree() in trace_parser_put(). However, it is
possible that trace_pid_write() is terminated due to unexpected errors,
e.g., ENOMEM. In that case, the allocated buffer will not be freed, which
is a memory leak bug.
To fix this issue, free the allocated buffer when an error is encountered.
Link: http://lkml.kernel.org/r/1555726979-15633-1-git-send-email-wang6495@umn.edu Fixes: f4d34a87e9c10 ("tracing: Use pid bitmap instead of a pid array for set_event_pid") Cc: stable@vger.kernel.org Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This fixes multiple issues in buffer_pipe_buf_ops:
- The ->steal() handler must not return zero unless the pipe buffer has
the only reference to the page. But generic_pipe_buf_steal() assumes
that every reference to the pipe is tracked by the page's refcount,
which isn't true for these buffers - buffer_pipe_buf_get(), which
duplicates a buffer, doesn't touch the page's refcount.
Fix it by using generic_pipe_buf_nosteal(), which refuses every
attempted theft. It should be easy to actually support ->steal, but the
only current users of pipe_buf_steal() are the virtio console and FUSE,
and they also only use it as an optimization. So it's probably not worth
the effort.
- The ->get() and ->release() handlers can be invoked concurrently on pipe
buffers backed by the same struct buffer_ref. Make them safe against
concurrency by using refcount_t.
- The pointers stored in ->private were only zeroed out when the last
reference to the buffer_ref was dropped. As far as I know, this
shouldn't be necessary anyway, but if we do it, let's always do it.
Link: http://lkml.kernel.org/r/20190404215925.253531-1-jannh@google.com Cc: Ingo Molnar <mingo@redhat.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@vger.kernel.org Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Dave Airlie [Fri, 26 Apr 2019 00:32:57 +0000 (10:32 +1000)]
Merge tag 'imx-drm-fixes-2019-04-25' of git://git.pengutronix.de/pza/linux into drm-fixes
drm/imx: fix DP CSC handling
- Fix the DP color space conversion matrix setup to avoid bugs where
disabling the overlay plane while both primary and overlay plane are
routed via the CSC unit would not reconfigure the CSC routing
properly, leaving the display in a nonworking state, or the CSC
setting from a previously set mode would be left behind, causing
wrong colors when reenabling the display in certain configurations.
sched_clock_cpu() may not be consistent between CPUs. If a task
migrates to another CPU, then se.exec_start is set to that CPU's
rq_clock_task() by update_stats_curr_start(). Specifically, the new
value might be before the old value due to clock skew.
So then if in numa_get_avg_runtime() the expression:
'now - p->last_task_numa_placement'
ends up as -1, then the divider '*period + 1' in task_numa_placement()
is 0 and things go bang. Similar to update_curr(), check if time goes
backwards to avoid this.
[ peterz: Wrote new changelog. ]
[ mingo: Tweaked the code comment. ]
Merge tag 'ceph-for-5.1-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"dentry name handling fixes from Jeff and a memory leak fix from Zheng.
Both are old issues, marked for stable"
* tag 'ceph-for-5.1-rc7' of git://github.com/ceph/ceph-client:
ceph: fix ci->i_head_snapc leak
ceph: handle the case where a dentry has been renamed on outstanding req
ceph: ensure d_name stability in ceph_dentry_hash()
ceph: only use d_name directly when parent is locked
Lijun Ou [Tue, 23 Apr 2019 09:30:26 +0000 (17:30 +0800)]
RDMA/hns: Bugfix for mapping user db
When the maximum send wr delivered by the user is zero, the qp does not
have a sq.
When allocating the sq db buffer to store the user sq pi pointer and map
it to the kernel mode, max_send_wr is used as the trigger condition, while
the kernel does not consider the max_send_wr trigger condition when
mapmping db. It will cause sq record doorbell map fail and create qp fail.
Fixes: 0425e3e6e0c7 ("RDMA/hns: Support flush cqe for hip08 in kernel space") Signed-off-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Nikolay Borisov [Mon, 1 Apr 2019 08:29:58 +0000 (11:29 +0300)]
btrfs: Switch memory allocations in async csum calculation path to kvmalloc
Recent multi-page biovec rework allowed creation of bios that can span
large regions - up to 128 megabytes in the case of btrfs. OTOH btrfs'
submission path currently allocates a contiguous array to store the
checksums for every bio submitted. This means we can request up to
(128mb / BTRFS_SECTOR_SIZE) * 4 bytes + 32bytes of memory from kmalloc.
On busy systems with possibly fragmented memory said kmalloc can fail
which will trigger BUG_ON due to improper error handling IO submission
context in btrfs.
Until error handling is improved or bios in btrfs limited to a more
manageable size (e.g. 1m) let's use kvmalloc to fallback to vmalloc for
such large allocations. There is no hard requirement that the memory
allocated for checksums during IO submission has to be contiguous, but
this is a simple fix that does not require several non-contiguous
allocations.
For small writes this is unlikely to have any visible effect since
kmalloc will still satisfy allocation requests as usual. For larger
requests the code will just fallback to vmalloc.
We've performed evaluation on several workload types and there was no
significant difference kmalloc vs kvmalloc.
Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[ 31.041908] [<c073273c>] (i2c_transfer) from [<c05926c4>] (drm_scdc_read+0x54/0x84)
[ 31.041913] [<c05926c4>] (drm_scdc_read) from [<c0592858>] (drm_scdc_set_scrambling+0x30/0xbc)
[ 31.041919] [<c0592858>] (drm_scdc_set_scrambling) from [<c05cc0f4>] (dw_hdmi_update_power+0x1440/0x1610)
[ 31.041926] [<c05cc0f4>] (dw_hdmi_update_power) from [<c05cc574>] (dw_hdmi_bridge_enable+0x2c/0x70)
[ 31.041932] [<c05cc574>] (dw_hdmi_bridge_enable) from [<c05aed48>] (drm_bridge_enable+0x24/0x34)
[ 31.041938] [<c05aed48>] (drm_bridge_enable) from [<c0591060>] (drm_atomic_helper_commit_modeset_enables+0x114/0x220)
[ 31.041943] [<c0591060>] (drm_atomic_helper_commit_modeset_enables) from [<c05c3fe0>] (rockchip_atomic_helper_commit_tail_rpm+0x28/0x64)
hdmi->i2c may not be set when ddc-i2c-bus property is used in device tree.
Fix this by using hdmi->ddc as the i2c adapter when calling drm_scdc_*().
Also report that SCDC is not supported when there is no DDC bus.
The err_remove_chip block is too coarse, and may perform cleanup that
must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove()
is still called, causing:
OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
[<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
[<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
[<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc)
[<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c)
[<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314)
[<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)
and later, if a GPIO consumer tries to use a GPIO from a failed
controller:
WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c
refcount_t: increment on 0; use-after-free.
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
[<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
[<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
[<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec)
[<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c)
[<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c)
[<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c)
[<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0)
[<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154)
[<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0)
[<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac)
[<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380)
[<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8)
[<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144)
[<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc)
[<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)
Fix this by splitting the cleanup block, and adding a missing call to
gpiochip_irqchip_remove().
Thomas Hellstrom [Tue, 23 Apr 2019 12:02:57 +0000 (14:02 +0200)]
drm/vmwgfx: Fix dma API layer violation
Remove the check for IOMMU presence since it was considered a
layer violation.
This means we have no reliable way to destinguish between coherent
hardware IOMMU DMA address translations and incoherent SWIOTLB DMA
address translations, which we can't handle. So always presume the
former. This means that if anybody forces SWIOTLB without also setting
the vmw_force_coherent=1 vmwgfx option, driver operation will fail,
like it will on most other graphics drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
Harry Pan [Wed, 24 Apr 2019 14:50:33 +0000 (22:50 +0800)]
perf/x86/intel: Update KBL Package C-state events to also include PC8/PC9/PC10 counters
Kaby Lake (and Coffee Lake) has PC8/PC9/PC10 residency counters.
This patch updates the list of Kaby/Coffee Lake PMU event counters
from the snb_cstates[] list of events to the hswult_cstates[]
list of events, which keeps all previously supported events and
also adds the PKG_C8, PKG_C9 and PKG_C10 residency counters.
This allows user space tools to profile them through the perf interface.
Signed-off-by: Harry Pan <harry.pan@intel.com> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: gs0622@gmail.com Link: http://lkml.kernel.org/r/20190424145033.1924-1-harry.pan@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
Merge tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Eric Dumazet [Wed, 24 Apr 2019 15:04:05 +0000 (08:04 -0700)]
ipv4: add sanity checks in ipv4_link_failure()
Before calling __ip_options_compile(), we need to ensure the network
header is a an IPv4 one, and that it is already pulled in skb->head.
RAW sockets going through a tunnel can end up calling ipv4_link_failure()
with total garbage in the skb, or arbitrary lengthes.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:355 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
Write of size 69 at addr ffff888096abf068 by task syz-executor.4/9204
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Apr 2019 16:44:11 +0000 (09:44 -0700)]
rxrpc: fix race condition in rxrpc_input_packet()
After commit 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook"),
rxrpc_input_packet() is directly called from lockless UDP receive
path, under rcu_read_lock() protection.
It must therefore use RCU rules :
- udp_sk->sk_user_data can be cleared at any point in this function.
rcu_dereference_sk_user_data() is what we need here.
- Also, since sk_user_data might have been set in rxrpc_open_socket()
we must observe a proper RCU grace period before kfree(local) in
rxrpc_lookup_local()
v4: @local can be NULL in xrpc_lookup_local() as reported by kbuild test robot <lkp@intel.com>
and Julia Lawall <julia.lawall@lip6.fr>, thanks !
v3,v2 : addressed David Howells feedback, thanks !
Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before the commit 490ea5967b0d ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit 490ea5967b0d ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M
The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us
cpu %
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.
Fixes: commit 490ea5967b0d ("RDS: IB: move FMR code to its own file") Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CIFS can leak pages reference gotten through GUP (get_user_pages*()
through iov_iter_get_pages()). This happen if cifs_send_async_read()
or cifs_write_from_iter() calls fail from within __cifs_readv() and
__cifs_writev() respectively. This patch move page unreference to
cifs_aio_ctx_release() which will happens on all code paths this is
all simpler to follow for correctness.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com> Cc: Steve French <sfrench@samba.org> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Frank Sorenson [Tue, 16 Apr 2019 13:37:27 +0000 (08:37 -0500)]
cifs: do not attempt cifs operation on smb2+ rename error
A path-based rename returning EBUSY will incorrectly try opening
the file with a cifs (NT Create AndX) operation on an smb2+ mount,
which causes the server to force a session close.
If the mount is smb2+, skip the fallback.
Signed-off-by: Frank Sorenson <sorenson@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Pan Bian [Fri, 19 Apr 2019 07:39:00 +0000 (07:39 +0000)]
Input: synaptics-rmi4 - fix possible double free
The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Jason Gunthorpe [Tue, 16 Apr 2019 11:07:28 +0000 (14:07 +0300)]
RDMA/ucontext: Fix regression with disassociate
When this code was consolidated the intention was that the VMA would
become backed by anonymous zero pages after the zap_vma_pte - however this
very subtly relied on setting the vm_ops = NULL and clearing the VM_SHARED
bits to transform the VMA into an anonymous VMA. Since the vm_ops was
removed this broke.
Now userspace gets a SIGBUS if it touches the vma after disassociation.
Instead of converting the VMA to anonymous provide a fault handler that
puts a zero'd page into the VMA when user-space touches it after
disassociation.
Cc: stable@vger.kernel.org Suggested-by: Andrea Arcangeli <aarcange@redhat.com> Fixes: 5f9794dc94f5 ("RDMA/ucontext: Add a core API for mmaping driver IO memory") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Jacky Bai [Fri, 5 Apr 2019 17:31:09 +0000 (10:31 -0700)]
Input: snvs_pwrkey - make it depend on ARCH_MXC
The SNVS power key is not only used on i.MX6SX and i.MX7D, it is also
used by i.MX6UL and NXP's latest ARMv8 based i.MX8M series SOC. So
update the config dependency to use ARCH_MXC, and add the COMPILE_TEST
too.
Jason Gunthorpe [Tue, 16 Apr 2019 11:07:26 +0000 (14:07 +0300)]
RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages
Since mlx5 supports device disassociate it must use this API for all
BAR page mmaps, otherwise the pages can remain mapped after the device
is unplugged causing a system crash.
Cc: stable@vger.kernel.org Fixes: 5f9794dc94f5 ("RDMA/ucontext: Add a core API for mmaping driver IO memory") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Reviewed-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Jason Gunthorpe [Tue, 16 Apr 2019 11:07:25 +0000 (14:07 +0300)]
RDMA/mlx5: Do not allow the user to write to the clock page
The intent of this VMA was to be read-only from user space, but the
VM_MAYWRITE masking was missed, so mprotect could make it writable.
Cc: stable@vger.kernel.org Fixes: 5c99eaecb1fc ("IB/mlx5: Mmap the HCA's clock info to user-space") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Reviewed-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
drm/vc4: Fix compilation error reported by kbuild test bot
A pointer to crtc was missing, resulting in the following build error:
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: sparse: incorrect type in argument 1 (different base types)
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: expected struct drm_crtc *crtc
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: got struct drm_crtc_state *state
drivers/gpu/drm/vc4/vc4_crtc.c:1045:39: sparse: sparse: not enough arguments for function vc4_crtc_destroy_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reported-by: kbuild test robot <lkp@intel.com> Cc: Eric Anholt <eric@anholt.net> Link: https://patchwork.freedesktop.org/patch/msgid/2b6ed5e6-81b0-4276-8860-870b54ca3262@linux.intel.com Fixes: d08106796a78 ("drm/vc4: Fix memory leak during gpu reset.") Cc: <stable@vger.kernel.org> # v4.6+ Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>