Arnd Bergmann [Tue, 2 Oct 2018 08:25:41 +0000 (10:25 +0200)]
Merge tag 'sunxi-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.20
Our usual bunch of DT patches for the Allwinner arm32 SoCs.
The most notable changes are:
- Support for the video decoding / encoding engine on the
A10s/A13/A20/A33
- IR support for the A83t
- SATA support for the R40
* tag 'sunxi-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun9i: Fix I2C bus warnings
ARM: dts: sunxi: Fix I2C bus warnings
ARM: dts: sun8i-a33: Add Video Engine and reserved memory nodes
ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes
ARM: dts: sun5i: Add Video Engine and reserved memory nodes
ARM: dts: sun8i: sun8i-r40-bananapi-m2-ultra: enable AHCI
ARM: dts: sun8i: r40: add sata node
ARM: dts: sunxi: Don't use cd-inverted in sun8i-r40-bananapi-m2-ultra
ARM: dts: sun8i: a83t: bananapi-m3: Enable IR controller
ARM: dts: sun8i: a83t: Add support for the cir interface
ARM: dts: sun8i: a83t: Add the cir pin for the A83T
Arnd Bergmann [Tue, 2 Oct 2018 08:19:31 +0000 (10:19 +0200)]
Merge tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3 and H5 DT additions for 4.20
This is our usual H3/H5 pull request
The most notable changes are:
- the video decoding / encoding unit is finally enabled on the H3
- Mali support for the H5
- New boards: BananaPi M2+ v1.2, Orange Pi Zero Plus 2 H3 support
* tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees
ARM: dts: sun8i-h3: Add Video Engine and reserved memory nodes
arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5
ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus
ARM: dts: sun8i: h3: bpi-m2-plus: Fix address for external RGMII Ethernet PHY
ARM: dts: sun8i: h3-h5: ir register size should be the whole memory block
arm64: dts: allwinner: h5: Add device node for Mali-450 GPU
ARM: dts: sun8i: Add initial Orangepi Zero Plus 2 H3 support
nvmem: sunxi-sid: add support for H5's SID controller
ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
ARM: dts: sun8i-h3: Add Video Engine and reserved memory nodes
This adds nodes for the Video Engine and the associated reserved memory
for the H3. Up to 96 MiB of memory are dedicated to the CMA pool.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Chen-Yu Tsai [Thu, 30 Aug 2018 08:09:25 +0000 (16:09 +0800)]
ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus
Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.
All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.
Chen-Yu Tsai [Fri, 24 Aug 2018 05:38:49 +0000 (13:38 +0800)]
arm64: dts: allwinner: h5: Add device node for Mali-450 GPU
The H5 has a Mali-450 GPU with 4 Pixel Processor cores.
Interestingly, while the datasheet lists an interrupt line for the GPU's
PMU, the hardware block itself doesn't seem to have it. Reads from the
PMU address range all return zero, and writes are ignored.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Diego Rondini [Fri, 3 Aug 2018 07:56:25 +0000 (09:56 +0200)]
ARM: dts: sun8i: Add initial Orangepi Zero Plus 2 H3 support
Orangepi Zero Plus 2 is an open-source single-board computer, available in two
Allwinner SOC variants, H3 and H5. We add support for H3 variant here, as the
H5 is already supported by sun50i-h5-orangepi-zero-plus2.dts.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
nvmem: sunxi-sid: add support for H5's SID controller
The H5 SoC have a SID controller that looks like the one in A64, the
cells are in the same offset but doesn't contain the same data (thermal
sensor calibration for example).
Add a binding for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Merge tag 'renesas-arm-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.20
* RZ/G1M (r8a7743) based iWave G20D-Q7 board and camera daughter board
- Move PCIe node out of common dtsi to allow reuse of the common dtsi
on the iWave RZ/G1N board
* RZ/G1C (r8a77470) SoC: Add I2C4, SDHI2 and SMP support
* R-Car Gen1 based boards and R-Car Gen2 SoCs:
- Enhance top-of-file comments to include SoC name
* RZ/N1D (r9a06g032) SoC:
- Correct UART0 description and add all other UARTs
* tag 'renesas-arm-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: iwg20d-q7-common: Move pciec node out of common dtsi
ARM: dts: r8a77470: Add I2C4 support
ARM: dts: r8a77470: Add SDHI2 support
ARM: dts: r8a77470: Add SMP support
ARM: dts: R-Car Gen1 board comment update
ARM: dts: Include R-Car Gen2 product name in DTSI files
ARM: dts: r9a06g032: Correct UART and add all other UARTs
Merge tag 'renesas-arm64-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM64 Based SoC DT Updates for v4.20
* Remove unneeded status from thermal nodes
* R-Car Gen 3 SoCs:
- Use 400kHz for I2C DVFS bus
- Revise USB2.0 properties
* R-Car Gen 3 SoC based ULCB boards: Add default bootargs
* R-Car M3-N (r8a77965) SoC based boards: Enable audio with DMA
* R-Car V3M (r8a77970 and V3H (r8a77980) SoCs:
- Add compare match timer (CMT) support
- Add timer pulse unit (TPU) support
* R-Car V3H (r8a77980) and E3 (r8a77990) SoCs:
- Attach the SYS-DMAC to the IPMMU
* E3 (r8a77990) SoC: Add display output support
* R-Car E3 (r8a77990) based Ebisu board:
- Enable HDMI and CVBS input, and VGA and HDMI display output
* R-Car D3 (r8a77995) SoC: Add LVDS support
* R-Car D3 (r8a77995) based Draak board: Enable HDMI display output
* tag 'renesas-arm64-dt2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77965: Add Sound and Audio DMAC device nodes
arm64: dts: renesas: r8a77995: draak: Enable HDMI display output
arm64: dts: renesas: r8a77990: ebisu: Enable VGA and HDMI outputs
arm64: dts: renesas: r8a77995: Add LVDS support
arm64: dts: renesas: r8a77990: Add display output support
arm64: dts: renesas: r8a779{7|8}0: add TPU support
arm64: dts: renesas: revise properties for R-Car Gen3 SoCs' usb 2.0
arm64: dts: renesas: ulcb: add default bootargs
arm64: dts: renesas: r8a779{7|8}0: add CMT support
arm64: dts: renesas: gen3: use 400kHz for I2C DVFS bus
arm64: dts: renesas: r8a77980: Attach the SYS-DMAC to the IPMMU
arm64: dts: renesas: r8a77990: Attach the SYS-DMAC to the IPMMU
arm64: dts: renesas: ebisu: Add HDMI and CVBS input
arm64: dts: renesas: Remove unneeded status from thermal nodes
Merge tag 'tegra-for-4.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
arm64: tegra: Device tree changes for v4.20-rc1
This contains mostly device tree changes to support faster SDHCI modes
on Tegra210 and Tegra186.
* tag 'tegra-for-4.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: I2C on Tegra194 is not compatible with Tegra114
arm64: dts: tegra186: Enable HS400
arm64: dts: tegra210: Enable HS400
arm64: dts: tegra186: Add SDMMC4 DQS trim value
arm64: dts: tegra210: Add SDMMC4 DQS trim value
arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4
arm64: dts: tegra210: Assign clocks for sdmmc1 and sdmmc4
arm64: dts: tegra186: Add SDHCI tap and trim values
arm64: dts: tegra210: Add SDHCI tap and trim values
arm64: dts: tegra186: Add sdmmc pad auto calibration offsets
arm64: dts: tegra210: Add sdmmc pad auto calibration offsets
arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1
arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply
arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V
arm64: dts: Add Tegra186 sdmmc pinctrl voltage states
arm64: dts: Add Tegra210 sdmmc pinctrl voltage states
Merge tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: Changes for v4.20-rc1
This contains the PMC pad configuration bindings which are used to
control the voltage of various pads found on Tegra chips. Among other
things this is required to enable faster modes on SDHCI.
* tag 'tegra-for-4.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add Tegra PMC pad configuration bindings
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic ARM64 DT updates for v4.20, round 2
- new SoC support: basic support for G12A family
- new board: Amlogic U200 board, using G12A SoC
- fix SPI bus warnings from new dtc updates
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson-g12a: add initial g12a s905d2 SoC DT support
dt-bindings: arm: amlogic: Add Meson G12A binding
arm64: dts: meson: Fix erroneous SPI bus warnings
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
ARM: dts: Amlogic updates for v4.20
- fix clock controller register sizes
- new board: Endless Mini (EC-100) by Endless Mobile
- add voltage regulators
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: odroidc1: add stdout-path property
ARM: dts: meson8b: odroidc1: enable the SAR ADC
ARM: dts: meson8b: odroidc1: add the fixed voltage regulators
ARM: dts: meson8b: odroidc1: add the CPU voltage regulator
ARM: dts: meson8b: Add support for the Endless Mini (EC-100)
ARM: dts: meson8b: add the RMII pins
ARM: dts: meson8b: add the I2C_A, PWM_C and UART_B pins
dt-bindings: arm: amlogic: Add the Endless Mobile Endless Mini (EC-100)
dt-bindings: add vendor prefix for "Endless Mobile, Inc."
ARM: dts: meson8b: fix the clock controller register size
ARM: dts: meson8: fix the clock controller register size
Merge tag 'berlin64-dt-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt
Berlin64 DT changes for v4.20
* tag 'berlin64-dt-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
arm64: dts: synaptics: add dtsi file for Synaptics AS370 SoC
dt-bindings: arm: syna: add support for the AS370 SoC
dt-bindings: arm: move berlin binding documentation to syna.txt
Rob Herring [Thu, 13 Sep 2018 18:12:40 +0000 (13:12 -0500)]
arm64: dts: amd: Fix SPI bus warnings
dtc has new checks for SPI buses. Fix the warnings in node names.
arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
Cc: Brijesh Singh <brijeshkumar.singh@amd.com> Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Biju Das [Fri, 21 Sep 2018 14:07:55 +0000 (15:07 +0100)]
ARM: dts: iwg20d-q7-common: Move pciec node out of common dtsi
PCIe is not populated by default on iWave RZ/G1N board. RZ/G1N board
is almost identical to RZ/G1M. In order to reuse the common dtsi for
both the boards, it is required to move pcie node from common dtsi
to board specific dts.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
The PHY found on the A64-OLinuXino requires a TX delay in order to
operate properly. Olimex uses a 600ps second delay in their BSP, and
that has been found to work, so let's use that value in the current
DT.
ARM: tegra: colibri_t20: iris: simplify model and compatible properties
Simplify model and compatible by dropping the 256/512 MB from the model,
-512 from the compatible and rename that property from toradex,iris to
toradex,colibri_t20-iris to be more in-line with all our other device
trees.
ARM: tegra: colibri_t20: simplify model and compatible properties
Simplify model and compatible by dropping the 256/512 MB from the model
and -512 from the compatible properties to be more in-line with all our
other device trees.
Annotate the SD card, its detect pin and move the SD card detect GPIO
definition from the module to the carrier board more in-line with our
other device trees.
Explicitly add pinmux' for all T20 SoC ball groups now:
- Colibri Address/Data Bus (GMI) further pins used as GPIOs
- Colibri BL_ON
- Colibri EXT_IO*
- Colibri L_BIAS, LCD_M1 is muxed with LCD_DE today's display need DE,
disable LCD_M1
- more Colibri LCD pins (L_* resp. LDD<*>)
- Colibri LCD (Optional 24 BPP Support)
- Colibri MMCCD
- uart_a_dsr and uart_a_dcd as GPIOs
- Colibri USB_CDET
- I2C3 (Optional)
- JTAG_RTCK
- LAN_RESET, LAN_EXT_WAKEUP and LAN_PME (All On-module)
- more NAND pins
- RESET_OUT
- THERMD_ALERT# (On-module), unlatched I2C address pin of LM95245
temperature sensor therefore requires disabling for now
Add missing regulators:
- reg_lan_v_bus being USB Ethernet chip vbus supply
- carrier board reg_3v3 to be used as backlight and panel power supply
- carrier board HDMI supply being reg_5v0
- reg_usbc_vbus being the USB vbus supply of the EHCI instance 0
Add missing regulators:
- reg_module_3v3_audio being VDDA supply of SGTL5000
- VDDD supply of SGTL5000 actually being reg_1v8_vio
- TMP451 temperature sensor vcc supply being reg_module_3v3
- usb3-0 vbus supply being reg_usbh_vbus
- usb3-1 vbus supply being reg_usbo1_vbus
- carrier board HDMI supply being reg_5v0
- carrier board sata target 5v supply being reg_5v0
- carrier board sata target 12v supply being reg_12v0
- carrier board reg_3v3 actually being backlight power supply
projects / kernel.git / log