Currently, the following #ifdef construct is used to check whether to run
console_record_init() during pre-relocation init:
defined(CONFIG_CONSOLE_RECORD) && CONFIG_VAL(SYS_MALLOC_F_LEN)
Introduce CONFIG_CONSOLE_RECORD_INIT_F Kconfig option to get rid of the
complex ifdef check. Also, use IS_ENABLED() instead of #ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Fri, 27 Nov 2020 10:20:59 +0000 (11:20 +0100)]
log: call vsnprintf only when it is needed to emit trace
Reduce the log overhead when the traces are filtered,
by moving the vsnprintf call from _log() to log_dispatch().
This patch avoids the printf treatment when LOG features is
activated, but trace is filtered, for example when
MAX_LOG_LEVEL=8 and LOG_DEFAULT_LEVEL=6.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Dario Binacchi [Fri, 15 Jan 2021 08:10:26 +0000 (09:10 +0100)]
dm: fix build errors generated by last merges
Something was wrong in the merge process into the mainline.
Some added patches access driver structure fields and functions that
have been modified by previous patches.
The patch renames:
- dev_get_platdata to dev_get_plat
- dev_get_uclass_platdata to dev_get_uclass_plat
- ofdata_to_platdata to of_to_plat
- plat_data_alloc_size to plat_auto
- priv_auto_alloc_size to priv_auto
- video_uc_platdata to video_uc_plat
Ley Foon Tan [Wed, 13 Jan 2021 10:53:05 +0000 (18:53 +0800)]
tools: socfpgaimage: update padding flow
The existing socfpgaimage always pads the image to the maximum size of
OCRAM size. This will break in the encryption flow where it expects the
image to be un-padded. The encryption tool will do the encryption for
the whole image and append the signature key at end of the image.
The signature key will append to beyond the size of OCRAM if the image
is padded with the maximum size before encryption.
Move the padding step from socfpgaimage to Makefile and pads with objcopy
command.
socfpgaimage will pad the image with 16 bytes aligned (including CRC word),
this is a requirement in encryption flow.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:21:10 +0000 (18:21 +0800)]
arm: socfpga: soc64: Skip handoff data access in SSBL
SPL already setup the Clock Manager with the handoff data
from OCRAM. When the Clock Manager's driver get probed again
in SSBL, it shall skip the handoff data access in OCRAM.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
mmc: dwmmc: Change designware MMC 'clksel' callback function to return status
Change 'clksel' callback function to allow the code to return a
status.
This patch is a preparation for enabling Arm-Trusted-Firmware (ATF)
in Intel SoC FPGA. This patch does not change functionality.
When using Arm-Trusted-Firmware (ATF) in Intel SoC FPGA, the MMC clock
related register is secure register which is required to be written
via SMC/PCSI call. It is possible that U-Boot fail to write the
register if there is unexpected error between U-Boot and ATF.
As a result, there maybe signal integrity on MMC connection due to
clock. So, the code should reports error to user when 'clksel' fail.
These secure register access functions allow U-Boot proper running
at EL2 (non-secure) to access System Manager's secure registers
by calling the ATF's PSCI runtime services (EL3/secure).
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:21:01 +0000 (18:21 +0800)]
arm: socfpga: soc64: Define SMC function identifiers for PSCI SiP services
This header file defines the Secure Monitor Call (SMC) message
protocol for ATF (BL31) PSCI runtime services. It includes all
the PSCI SiP function identifiers for the secure runtime services
provided by ATF. The secure runtime services include System Manager's
registers access, 2nd phase bitstream FPGA reconfiguration, Remote
System Update (RSU) and etc.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:21:00 +0000 (18:21 +0800)]
arm: socfpga: soc64: Add SMC helper function for Intel SOCFPGA (64bits)
invoke_smc() allow U-Boot proper running in non-secure mode (EL2)
to invoke SMC call to ATF's PSCI runtime services such as
System Manager's registers access, 2nd phase bitstream FPGA
reconfiguration, Remote System Update (RSU) and etc.
smc_send_mailbox() is a send mailbox command helper function which invokes
the ATF's PSCI runtime service (function ID: INTEL_SIP_SMC_MBOX_SEND_CMD)
to send mailbox messages to Secure Device Manager (SDM).
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:20:59 +0000 (18:20 +0800)]
arm: socfpga: Disable "spin-table" method for booting Linux
Standard PSCI function "CPU_ON" provided by ATF is now used
by Linux kernel to bring up the secondary CPUs to enable SMP
booting in Linux on SoC 64bits platform.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:20:58 +0000 (18:20 +0800)]
arm: socfpga: soc64: Override 'lowlevel_init' to support ATF
Override 'lowlevel_init' to make sure secondary CPUs trapped
in ATF instead of SPL. After ATF is initialized, it will signal
the secondary CPUs to jump from SPL to ATF waiting to be 'activated'
by Linux OS via PSCI call.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Chee Hong Ang [Thu, 24 Dec 2020 10:20:56 +0000 (18:20 +0800)]
arm: socfpga: Add function for checking description from FIT image
Add board_fit_config_name_match() for matching board name with
device tree files in FIT image. This will ensure correct DTB
file is loaded for different board type. Currently, we are not
supporting multiple device tree files in FIT image therefore this
function basically do nothing for now.
Users are allowed to override this 'weak' function in their
specific board implementation.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Tom Rini [Wed, 13 Jan 2021 20:00:53 +0000 (15:00 -0500)]
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
Tom Rini [Tue, 12 Jan 2021 20:46:52 +0000 (15:46 -0500)]
Merge tag 'u-boot-amlogic-20210112' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- sync amlogic GX & AXG DT to Linux 5.10
- Add new MESON_EE driver support for GXBB & AXG
- Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards
- add driver for TDO tl070wsh30 panel driver
- meson: isolate loading of socinfo
- Add soc_rev to environment
- Enable G12A support for saradc
- Add correct mmcdev on VIM3(L) & Odroid-N2(C4)
- Read MAC from fuses for VIM3 & VIM3L boards
Patrice Chotard [Mon, 4 Jan 2021 16:00:56 +0000 (17:00 +0100)]
MAINTAINERS: Update STi and STM32 maintainers emails in remaining files
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Patrick Delaunay [Fri, 11 Dec 2020 12:36:18 +0000 (13:36 +0100)]
arm: stm32mp: stm32prog: always flush DFU on start command for uart
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 06d2b86c8e5e ("stm32mp: stm32prog: add serial link support") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrick Delaunay [Fri, 11 Dec 2020 14:32:30 +0000 (15:32 +0100)]
configs: stm32mp1: activate OF_LIVE for DT live support
Activate the live DT to reduce the DT parsing time.
For example the boot time is reduced by 200ms on STM32MP157C-EV1 board
for stm32mp15_basic_defconfig (boot with SPL) or
stm32mp15_trusted_defconfig (boot with TF-A).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 10:34:48 +0000 (11:34 +0100)]
ARM: dts: stm32: Switch to MCO2 for PHY 50 MHz clock
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
Michal Simek [Mon, 5 Oct 2020 09:37:00 +0000 (11:37 +0200)]
ARM: stm32: Use firmware property instead of loadables
There shouldn't be a need to use loadables propertyn because u-boot can be
pointed by firmware property. This change should also speedup boot process
because loadables property is list of strings which code is going through.
On the other hand firmware can just point to one image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Fri, 16 Oct 2020 07:28:59 +0000 (09:28 +0200)]
board: stm32pm1: update USB-C power detection algorithm on DK boards
USB-C power supply which are Power Delivery compliant (USB-PD) are able
to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...)
In this case, the power supply need to negotiate the voltage/current to
use with the device using CC1/CC2 USB-C signals.
If this negotiation occurs during ADC measurement (done also on CC1/CC2
USB-C signals) some ADC acquisition can be corrupted which cause wrong
power supply current detection.
To avoid this, the power supply current detection algorithm is updated
as following:
- perform an ADC measurement, if a 3A current is detected, continue the
boot process.
- else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD
negotiation is done and perform another ADC measurement.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
mmc: stm32_sdmmc2: migrate trace to dev and log macro
Define LOG_CATEGORY, use dev_ macro when it is possible.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
* apply U-Boot's fix-ups to the a device-tree
* let U-Boot make memory reservations according to the device-tree
* install the device-tree as a configuration table
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now the bootefi command used the last file loaded to determine the
boot partition. This has led to errors when the fdt had been loaded from
another partition after the EFI binary.
Before setting the boot device from a loaded file check if it is a PE-COFF
image or a FIT image.
For a PE-COFF image remember address and size, boot device and path.
For a FIT image remember boot device and path.
If the PE-COFF image is overwritten by loading another file, forget it.
Do not allow to start an image via bootefi which is not the last loaded
PE-COFF image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently when executing 'bootefi hello' we copy helloworld.efi to the
address identified by environment variable loadaddr. This is unexected
behavior for a user. There is no need to copy helloworld.efi before
executing it after relocation.
Remove the copy action.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When tools: efivar.py is called without arguments an error occurs:
Traceback (most recent call last):
File "tools/efivar.py", line 380, in <module>
main()
File "tools/efivar.py", line 360, in main
args.func(args)
AttributeError: 'Namespace' object has no attribute 'func'
Show the online help if the arguments do not specify a function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Tom Rini [Tue, 12 Jan 2021 14:32:48 +0000 (09:32 -0500)]
Merge tag 'ti-v2021.04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
Tom Rini [Tue, 12 Jan 2021 14:32:20 +0000 (09:32 -0500)]
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
projects / uboot.git / log