Chris Wilson [Wed, 21 Aug 2019 04:20:44 +0000 (05:20 +0100)]
drm/i915/gtt: Relax assertion for pt_used
When inserting the final level PTE, we check that we are not overflowing
the page table (checking that pt_used does not exceed the size of the
table). However, we have to allow for every other PTE to be pinned by a
simultaneous removal thread (as on remove we bump the pt_used counter
before adjusting the table).
drm/i915/tgl: Move transcoders to pipes' powerwells
When trying to read registers from transcoder C and D while PG3 is ON it
causes unclaimed access warnings. Adding the powerwells for the pipes
fixes the issue, but doesn't match the spec.
Lucas De Marchi [Wed, 14 Aug 2019 23:55:17 +0000 (16:55 -0700)]
drm/i915/tgl: disable DDIC
The current SKUs added for Tiger Lake don't have DDIC hooked up, even
though it is supported by the SoC. The current state for these SKUs is
problematic since while enabling the combo phy, PORT_COMP_DW* return
0xFFFFFFFF, which is invalid per register definition.
During initialization we check what phys are not yet enabled by reading
PHY_MISC_C and try to enable it by toggling the "DE to IO Comp Pwr Down"
bit. But after that any read to the PORT_COMP_DW* returns invalid
results. This removes the following warning
We may or may not need to change the implementation to account for DDIC
being available on other SKUs. For now I think the best thing to do is
to just disable the port.
Chris Wilson [Tue, 20 Aug 2019 14:12:18 +0000 (15:12 +0100)]
drm/i915/gtt: Relax pd_used assertion
The current assertion tries to make sure that we do not over count the
number of used PDE inside a page directory -- that is with an array of
512 pde, we do not expect more than 512 elements used! However, our
assertion has to take into account that as we pin an element into the
page directory, the caller first pins the page directory so the usage
count is one higher. However, this should be one extra pin per thread,
and the upper bound is that we may have one thread for each entry.
drm/i915: Dynamically allocate s0ix struct for VLV
This is only required for a single platform so no need to reserve the
memory on all of them.
This removes the last direct dependency of i915_drv.h on i915_reg.h
(apart from the i915_reg_t definition).
v2: drop unneeded diff, keep the vlv prefix, call functions
unconditionally (Jani), fwd declaration of the struct (Chris)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190820020147.5667-1-daniele.ceraolospurio@intel.com
Michel Thierry [Sat, 17 Aug 2019 09:38:54 +0000 (02:38 -0700)]
drm/i915/tgl: Updated Private PAT programming
Gen12 removes the target-cache and age fields from the private PAT
because MOCS now have the capability to set these itself. Only memory-type
field should be programmed in the ppat, the reminded bits are reserved.
Since now there are only 4 possible combinations, we could set only 4
PPAT and leave the reminded 4 as UC, but I left them as WB as we used
to have before.
Also these registers have been relocated to the 0x4800-0x481c range.
HSDES: 1406402661
BSpec: 31654 Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-33-lucas.demarchi@intel.com
Lucas De Marchi [Sat, 17 Aug 2019 09:38:42 +0000 (02:38 -0700)]
drm/i915/tgl: Introduce initial Tiger Lake workarounds
Add empty workaround hooks for Tiger Lake. The workarounds will be added
on separate patches. We were already applying
WaRsForcewakeAddDelayForAck, which is indeed still valid, so also update
the comment.
The CSB format has been reworked for Gen12 to include information on
both the context we're switching away from and the context we're
switching to. After the change, some of the events don't have their
own bit anymore and need to be inferred from other values in the csb.
One of the context IDs (0x7FF) has also been reserved to indicate
the invalid ctx, i.e. engine idle.
Note that the full context ID includes the SW counter as well, but since
we currently only care if the context is valid or not we can ignore that
part.
v2: fix mask size, fix and expand comments (Tvrtko),
use if-ladder (Chris)
Bspec: 45555, 46144 Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190820102201.29849-1-chris@chris-wilson.co.uk
Like Gen11, Gen12 has 11 available bits for the ctx id field. However,
the last value (0x7FF) is reserved to indicate engine idle, so we
need to reduce the maximum number of contexts by 1 compared to Gen11.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-29-lucas.demarchi@intel.com
Michel Thierry [Wed, 31 Jul 2019 00:49:02 +0000 (17:49 -0700)]
drm/i915/tgl: Report valid VDBoxes with SFC capability
In Gen11, only even numbered "logical" VDBoxes are hooked up to a SFC
(Scaler & Format Converter) unit. This is not the case in Tigerlake,
where each VDBox can access a SFC.
We will use this information to decide when the SFC units need to be reset
and also pass it to the GuC.
Bspec: 48077 Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190731004902.34672-5-daniele.ceraolospurio@intel.com
Chris Wilson [Tue, 20 Aug 2019 08:09:07 +0000 (09:09 +0100)]
drm/i915: Serialize insertion into the file->mm.request_list
Currently, we remove the from per-file request list for throttling and
retirement under a dedicated spinlock, but insertion is governed by
struct_mutex. This needs to be the same lock so that the
retirement/insertion of neighbouring requests (at the tail) doesn't
break the list.
Imre Deak [Fri, 16 Aug 2019 09:55:23 +0000 (12:55 +0300)]
drm/i915: Sanitize PHY state during display core uninit
To work around a DMC/Punit issue on ICL where the driver's
ICL_PORT_COMP_DW8/IREFGEN PHY setting is lost when entering/exiting DC6
state, make sure to reinit the PHY whenever disabling DC states.
Similarly the driver's PHY/DBUF/CDCLK settings should have been preserved
across DC5/6 transitions, so check this on all platforms.
This gets rid of the following WARN during suspend:
Combo PHY A HW state changed unexpectedly
Chris Wilson [Mon, 19 Aug 2019 20:07:05 +0000 (21:07 +0100)]
drm/i915: Assume exclusive access to objects inside resume
Inside gtt_restore_mappings() we currently take the obj->resv->lock, but
in the future we need to avoid taking this fs-reclaim tainted lock as we
need to extend the coverage of the vm->mutex. Take advantage of the
single-threaded nature of the early resume phase, and do a single
wbinvd() to flush all the GTT objects en masse.
Chris Wilson [Mon, 19 Aug 2019 18:44:03 +0000 (19:44 +0100)]
drm/i915: Use 0 for the unordered context
Since commit c57fc8542af3 ("dma-buf: add dma_fence_get_stub") the 0
fence context became an impossible match as it is used for an always
signaled fence. We can simplify our timeline tracking by knowing that 0
always means no match.
Matt Roper [Sat, 17 Aug 2019 00:50:41 +0000 (17:50 -0700)]
drm/i915/gen11: Allow usage of all GPIO pins
Our pin mapping tables for ICP and MCC currently only list the standard
GPIO pins used for various output ports. Even through ICP's standard
pin usage only utilizes pins 1, 2, and 9-12, and MCC's standard pin
usage only uses pins 1, 2, and 9, these platforms do still have GPIO
registers to address pins in the range 1-3 and 9-14. OEM's may remap
GPIO usage in non-standard ways (and provide the actual mapping via VBT
settings), so we shouldn't exclude pins on these platforms just because
they aren't part of the standard mappings.
TGP's standard pin tables contains all the possible pins, so let's
rename them to "icp" and use them for all PCH >= PCH_ICP. This will
prevent intel_gmbus_is_valid_pin from rejecting non-standard pin usage
that an OEM specifies via the VBT.
Note that this will cause pin 9 to be labeled as "tc1" instead of "dpc"
in debug messages on platforms with the MCC PCH, but that may actually
help avoid confusion since the text strings will now be the same on all
gen11+ platforms instead of being different on just EHL.
v2: Drop now-unused MCC_DDC_BUS_DDI_* names.
v3: We want to compare against INTEL_PCH_TYPE, not INTEL_PCH_ID.
Bspec: 8417 Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Vivek Kasireddy <vivek.kasireddy@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190817005041.20651-1-matthew.d.roper@intel.com
Chris Wilson [Mon, 19 Aug 2019 07:58:19 +0000 (08:58 +0100)]
drm/i915/gt: Mark up the nested engine-pm timeline lock as irqsafe
We use a fake timeline->mutex lock to reassure lockdep that the timeline
is always locked when emitting requests. However, the use inside
__engine_park() may be inside hardirq and so lockdep now complains about
the mixed irq-state of the nested locked. Disable irqs around the
lockdep tracking to keep it happy.
Fixes: 1e28740e8569 ("drm/i915/gt: Mark context->active_count as protected by timeline->mutex") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190819075835.20065-3-chris@chris-wilson.co.uk
Chris Wilson [Sat, 17 Aug 2019 23:25:11 +0000 (00:25 +0100)]
drm/i915: Propagate fence errors
Errors spread like wildfire, and must eventually be returned to the
user. They need to be captured and passed along the flow of fences,
infecting each in turn with the existing error, until finally they fall
out of a user visible result.
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:04 +0000 (09:52 +0000)]
drm/i915/uc: Never fail on HuC firmware errors
There is no need to mark whole GPU as wedged just because
of the custom HuC fw failure as users can always verify
actual HuC firmware status using existing HUC_STATUS ioctl.
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:03 +0000 (09:52 +0000)]
drm/i915/uc: Don't always fail on unavailable GuC firmware
If we failed to fetch default GuC firmware and we didn't plan
to use it for the submission and we never have used GuC before
then we may continue normal driver load, no need to declare
GPU wedged (we can use execlist for submission) and it is safe
to run without the HuC (users will check HuC status anyway).
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:02 +0000 (09:52 +0000)]
drm/i915/guc: Don't open log relay if GuC is not running
As we plan to continue driver load after GuC initialization
failure, we can't assume that GuC log data will be available
just because GuC was initially enabled. We must check that
GuC is still running instead.
Michal Wajdeczko [Sat, 17 Aug 2019 13:11:43 +0000 (13:11 +0000)]
drm/i915/uc: Cleanup fw fetch on every GuC/HuC init failure
Be consistent and always perform fw fetch cleanup in GuC/HuC specific
init functions on every failure. Also while converting firmware
status to error, stop treating SELECTED as non-error, as long term
we should not see it.
Michal Wajdeczko [Sat, 17 Aug 2019 13:11:42 +0000 (13:11 +0000)]
drm/i915/uc: Cleanup fw fetch only if it was successful
We can rely on firmware status AVAILABLE to determine if any
firmware cleanup is required. Also don't unconditionally reset
fw status to SELECTED as we will loose MISSING/ERROR codes.
Chris Wilson [Sat, 17 Aug 2019 07:37:11 +0000 (08:37 +0100)]
drm/i915/selftests: Check the context size
Add a redzone to our context image and check the HW does not write into
after a context save, to verify that we have the correct context size.
(This does vary with feature bits, so test with a live setup that should
match how we run userspace.)
v2: Check the redzone on every context unpin
v3: Use a kernel context to prevent loading garbage for ringbuffer
submission
Mika Kuoppala [Fri, 16 Aug 2019 09:47:54 +0000 (12:47 +0300)]
drm/i915/gtt: Fold gen8 insertions into one
As we give page directory pointer (lvl 3) structure
for pte insertion, we can fold both versions into
one function by teaching it to get pdp regardless
of top level.
Michal Wajdeczko [Fri, 16 Aug 2019 20:56:58 +0000 (20:56 +0000)]
drm/i915/uc: Add explicit DISABLED state for firmware
We really need to have separate NOT_SUPPORTED state (for
lack of hardware support) and DISABLED state (to indicate
user decision) as we will have to take special steps even
if GuC firmware is now disabled but hardware exists and
could have been previously used.
v2: fix logic (Chris/CI)
v3: use proper check to avoid probe failure (CI)
v4: explain status transitions (Chris)
To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.
Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Chris Wilson [Fri, 16 Aug 2019 17:16:08 +0000 (18:16 +0100)]
drm/i915/execlists: Lift process_csb() out of the irq-off spinlock
If we only call process_csb() from the tasklet, though we lose the
ability to bypass ksoftirqd interrupt processing on direct submission
paths, we can push it out of the irq-off spinlock.
The penalty is that we then allow schedule_out to be called concurrently
with schedule_in requiring us to handle the usage count (baked into the
pointer itself) atomically.
As we do kick the tasklets (via local_bh_enable()) after our submission,
there is a possibility there to see if we can pull the local softirq
processing back from the ksoftirqd.
v2: Store the 'switch_priority_hint' on submission, so that we can
safely check during process_csb().
Chris Wilson [Fri, 16 Aug 2019 12:10:00 +0000 (13:10 +0100)]
drm/i915: Markup expected timeline locks for i915_active
As every i915_active_request should be serialised by a dedicated lock,
i915_active consists of a tree of locks; one for each node. Markup up
the i915_active_request with what lock is supposed to be guarding it so
that we can verify that the serialised updated are indeed serialised.
Chris Wilson [Fri, 16 Aug 2019 12:09:59 +0000 (13:09 +0100)]
drm/i915/gt: Mark context->active_count as protected by timeline->mutex
We use timeline->mutex to protect modifications to
context->active_count, and the associated enable/disable callbacks.
Due to complications with engine-pm barrier there is a path where we used
a "superlock" to provide serialised protect and so could not
unconditionally assert with lockdep that it was always held. However,
we can mark the mutex as taken (noting that we may be nested underneath
ourselves) which means we can be reassured the right timeline->mutex is
always treated as held and let lockdep roam free.
Michal Wajdeczko [Fri, 16 Aug 2019 10:54:59 +0000 (10:54 +0000)]
drm/i915/wopcm: Try to use already locked WOPCM layout
If WOPCM layout is already locked in HW we shouldn't continue
with our own partitioning as it could be likely different and
we will be unable to enforce it and fail. Instead we should try
to reuse what is already programmed, maybe there will be a fit.
This should enable us to reload driver with slightly different
HuC firmware (or even without HuC) without need to reboot.
v2: reordered/rebased
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michal Winiarski <michal.winiarski@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190816105501.31020-4-michal.wajdeczko@intel.com
Michał Winiarski [Fri, 16 Aug 2019 10:54:57 +0000 (10:54 +0000)]
drm/i915/uc: Move FW size sanity check back to fetch
While we need to know WOPCM size to do this sanity check, it has more to
do with FW than with WOPCM. Let's move the check to fetch phase, it's
not like WOPCM is going to grow in the meantime.
v2: rebased
v3: use __intel_uc_fw_get_upload_size (Daniele)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jackie Li <yaodong.li@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190816105501.31020-2-michal.wajdeczko@intel.com
Matthew Auld [Fri, 16 Aug 2019 10:53:57 +0000 (11:53 +0100)]
drm/i915/buddy: use kmemleak_update_trace
Since nodes are cached in a free-list, and potentially marked as free
without actually being destroyed, thus allowing them to be
opportunistically re-allocated, we should apply kmemleak_update_trace
every time a node is given a new owner and marked as allocated, to aid
in debugging.
Chris Wilson [Fri, 16 Aug 2019 07:46:35 +0000 (08:46 +0100)]
drm/i915: Extract intel_frontbuffer active tracking
Move the active tracking for the frontbuffer operations out of the
i915_gem_object and into its own first class (refcounted) object. In the
process of detangling, we switch from low level request tracking to the
easier i915_active -- with the plan that this avoids any potential
atomic callbacks as the frontbuffer tracking wishes to sleep as it
flushes.
Chris Wilson [Thu, 15 Aug 2019 20:57:09 +0000 (21:57 +0100)]
drm/i915: Protect request retirement with timeline->mutex
Forgo the struct_mutex requirement for request retirement as we have
been transitioning over to only using the timeline->mutex for
controlling the lifetime of a request on that timeline.
Chris Wilson [Thu, 15 Aug 2019 20:57:08 +0000 (21:57 +0100)]
drm/i915/gt: Guard timeline pinning without relying on struct_mutex
In preparation for removing struct_mutex from around context retirement,
we need to make timeline pinning and unpinning safe. Since multiple
engines/contexts can share a single timeline, we cannot rely on
borrowing the context mutex (otherwise we could state that the timeline
is only pinned/unpinned inside the context pin/unpin and so guarded by
it). However, we only perform a sequence of atomic operations inside the
timeline pin/unpin and the sequence of those operations is safe for a
concurrent unpin / pin, so we can relax the struct_mutex requirement.
Chris Wilson [Thu, 15 Aug 2019 20:57:07 +0000 (21:57 +0100)]
drm/i915/gt: Convert timeline tracking to spinlock
Convert the active_list manipulation of timelines to use spinlocks so
that we can perform the updates from underneath a quick interrupt
callback, if need be.
Chris Wilson [Thu, 15 Aug 2019 04:20:30 +0000 (05:20 +0100)]
drm/i915: Move tasklet kicking to __i915_request_queue caller
Since __i915_request_queue() may be called from hardirq (timer) context,
we cannot use local_bh_disable/enable at the lower level. As we do want
to kick the tasklet to speed up initial submission or preemption for
normal client submission, lift it to the normal process context
callpath.
Mika Kuoppala [Thu, 15 Aug 2019 09:49:29 +0000 (12:49 +0300)]
drm/i915/icl: Add gen11 specific render breadcrumbs
Flush according to what gen11 expects when writing
breadcrumbs. As only the seqnowrite + flush differs
between engine and gens, enclose the footer to
helper.
v2: avoid problem of sane local naming by not using them
Mika Kuoppala [Thu, 15 Aug 2019 08:30:53 +0000 (11:30 +0300)]
drm/i915/icl: Implement gen11 flush including tile cache
Add tile cache flushing for gen11. To relive us from the
burden of previous obsolete workarounds, make a dedicated
flush/invalidate callback for gen11.
To fortify an independent single flush, do post
sync op as there are indications that without it
we don't flush everything. This should also make this
callback more readily usable in tgl (see l3 fabric flush).
Dan reported the following static checker warning:
drivers/gpu/drm/i915/selftests/i915_buddy.c:670 igt_buddy_alloc_range()
error: we previously assumed 'block' could be null (see line 665)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190815103210.11802-1-matthew.auld@intel.com
Chris Wilson [Thu, 15 Aug 2019 09:36:04 +0000 (10:36 +0100)]
drm/i915: Convert a few more bland dmesg info to be device specific
Looking around the GT initialisation, we have a few log messages we
think are interesting enough present to the user (such as the amount of L4
cache) and a few to inform them of the result of actions or conflicting
HW restrictions (i.e. quirks). These are device specific messages, so
use the dev family of printk.
Chris Wilson [Tue, 13 Aug 2019 20:09:05 +0000 (21:09 +0100)]
drm/i915: Serialise read/write of the barrier's engine
We use the request pointer inside the i915_active_node as the indicator
of the barrier's status; we mark it as used during
i915_request_add_active_barriers(), and search for an available barrier
in reuse_idle_barrier(). That check must be carefully serialised to
ensure we do use an engine for the barrier and not just a random
pointer. (Along the other reuse path, we are fully serialised by the
timeline->mutex.) The acquisition of the barrier itself is ordered through
the strong memory barrier in llist_del_all().
Chris Wilson [Tue, 13 Aug 2019 18:21:12 +0000 (19:21 +0100)]
drm/i915: Disregard drm_mode_config.fb_base
The fb_base is only used for communicating the GTT BAR from one piece of
the display code (kms setup) to another (fbdev). What is required in the
fbdev is just the aperture address which should be derived from the
bo we allocate for the framebuffer directly.
The same appears true for drm/; it is not used by the core or the uAPI,
it is merely for conveniently passing a device address from bit of
display management code to another.
v2: Note that since we only expose enough of a system map to cover our
single framebuffer, the screen_base/size and the smem are one and the
same.
The engine->guc_id is GuC FW defined and it is not guaranteed to be
below I915_NUM_ENGINES, so we shouldn't use it with the i915-defined
client->submissions, as we might overflow.
Instead of fixing it, just get rid of client->submissions, because the
information we get from it is not interesting anymore now that we only
have 1 client.
A new macro that is going to be added in a further patch will need to
adjust the offset returned by _MMIO_TRANS2(), so here adding
_TRANS2() and moving most of the implementation of _MMIO_TRANS2() to
it and while at it taking the opportunity to rename pipe to trans.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Dhinakaran Pandiyan <dhinakaran.pandiya@intel.com> Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiya@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190730224753.14907-2-jose.souza@intel.com
Chris Wilson [Tue, 13 Aug 2019 19:07:05 +0000 (20:07 +0100)]
drm/i915: Push the wakeref->count deferral to the backend
If the backend wishes to defer the wakeref parking, make it responsible
for unlocking the wakeref (i.e. bumping the counter). This allows it to
time the unlock much more carefully in case it happens to needs the
wakeref to be active during its deferral.
For instance, during engine parking we may choose to emit an idle
barrier (a request). To do so, we borrow the engine->kernel_context
timeline and to ensure exclusive access we keep the
engine->wakeref.count as 0. However, to submit that request to HW may
require a intel_engine_pm_get() (e.g. to keep the submission tasklet
alive) and before we allow that we have to rewake our wakeref to avoid a
recursive deadlock.
drm/i915/tgl: Fix missing parentheses on TGL_TRANS_DDI_FUNC_CTL_VAL_TO_PORT
In this case we want to apply the mask and then shift so the
parentheses is needed.
SPANK! SPANK! SPANK! Naughty programmer!
Fixes: da00894bab3f ("drm/i915/tgl: Fix the read of the DDI that transcoder is attached to") Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190812175405.14479-1-jose.souza@intel.com
Gao, Fred [Thu, 18 Jul 2019 01:39:01 +0000 (09:39 +0800)]
drm/i915/gvt: Utility for valid command length check
Add utility for valid command length check.
v2: Add F_VAL_CONST flag to identify the value is const
although LEN maybe variable. (Zhenyu)
v3: unused code removal, flag rename/conflict. (Zhenyu)
v4: redefine F_IP_ADVANCE_CUSTOM and move the check function to
next patch. (Zhenyu)
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Gao, Fred <fred.gao@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Zhi Wang [Mon, 22 Jul 2019 11:07:07 +0000 (14:07 +0300)]
drm/i915/gvt: factor out tlb and mocs register offset table
Factor out tlb and mocs register offset table to fix the issues reported
by klocwork, #512 and #550. Mostly, the reason why the klocwork reports
these problems is because there can be possbilities for platforms, which
have more rings than the ring offset table, to take the dirty data from
the stack as the register offset. It results to a random HW register
offset writting in this scenairo when doing context switch between vGPUs.
After the factoring, the ring offset table of TLB and MOCS should be per
platform.
v2:
- Enable TLB register switch for GEN8. (Zhenyu)
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
drm/i915/gvt: no need to check return value of debugfs_create functions
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because there is no need to check these functions, a number of local
functions can be made to return void to simplify things as nothing can
fail.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Zhi Wang <zhi.a.wang@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: intel-gvt-dev@lists.freedesktop.org Cc: intel-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Michal Wajdeczko [Tue, 13 Aug 2019 08:15:59 +0000 (08:15 +0000)]
drm/i915/uc: Log fw status changes only under debug config
We don't care about internal firmware status changes unless
we are doing some real debugging. Note that our CI is not
using DRM_I915_DEBUG_GUC config by default so use it.
Chris Wilson [Mon, 12 Aug 2019 20:36:26 +0000 (21:36 +0100)]
drm/i915/guc: Use a local cancel_port_requests
Since execlists and the guc have diverged in their port tracking, we
cannot simply reuse the execlists cancellation code as it leads to
unbalanced reference counting. Use a local, simpler routine for the guc.
We rely on the tasklet to update the GT PM refcount, so we can't disable
it even if we've processed all the requests for the engine because we
might have detected the request completion before the interrupt arrived.
Since on all platforms on which we plan to support guc submission we
don't allow disabling the breadcrumb interrupts, we can further siplify
the park/unpark flow by removing the interrupt pin/unpin. A BUG_ON has
been added to catch changes to this flow that would require us to
restore some kind of pinning.
v2: split removal of engine_pin/unpin_breadcrumbs_irq to its own
patch (chris)
Chris Wilson [Mon, 12 Aug 2019 17:48:04 +0000 (18:48 +0100)]
drm/i915/overlay: Switch to using i915_active tracking
Remove the raw i915_active_request tracking in favour of the higher
level i915_active tracking for the sole purpose of making the lockless
transition easier in later patches.
Chris Wilson [Mon, 12 Aug 2019 17:48:03 +0000 (18:48 +0100)]
drm/i915: Forgo last_fence active request tracking
We were using the last_fence to track the last request that used this
vma that might be interpreted by a fence register and forced ourselves
to wait for this request before modifying any fence register that
overlapped our vma. Due to requirement that we need to track any XY_BLT
command, linear or tiled, this in effect meant that we have to track the
vma for its active lifespan anyway, so we can forgo the explicit
last_fence tracking and just use the whole vma->active.
Another solution would be to pipeline the register updates, and would
help resolve some long running stalls for gen3 (but only gen 2 and 3!)
Andi Shyti [Sun, 11 Aug 2019 21:06:33 +0000 (22:06 +0100)]
drm/i915: Extract general GT interrupt handlers
i915_irq.c is large. It serves as the central dispatch and handler for
all of our device interrupts. Lets break it up by pulling out the GT
interrupt handlers.
i915_irq.c is large. It serves as the central dispatch and handler for
all of our device interrupts. Pull out the GT pm interrupt handling
(leaving the central dispatch) so that we can encapsulate the logic a
little better.
Chris Wilson [Mon, 12 Aug 2019 09:10:38 +0000 (10:10 +0100)]
drm/i915/execlists: Avoid sync calls during park
Since we allow ourselves to use non-process context during parking, we
cannot allow ourselves to sleep and in particular cannot call
del_timer_sync() -- but we can use a plain del_timer().
projects / kernel.git / log