Daniel Borkmann [Thu, 20 Jul 2017 22:00:25 +0000 (00:00 +0200)]
bpf: more tests for mixed signed and unsigned bounds checks
Add a couple of more test cases to BPF selftests that are related
to mixed signed and unsigned checks.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Thu, 20 Jul 2017 22:00:24 +0000 (00:00 +0200)]
bpf: add test for mixed signed and unsigned bounds checks
These failed due to a bug in verifier bounds handling.
Signed-off-by: Edward Cree <ecree@solarflare.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Jul 2017 22:00:23 +0000 (00:00 +0200)]
bpf: fix up test cases with mixed signed/unsigned bounds
Fix the few existing test cases that used mixed signed/unsigned
bounds and switch them only to one flavor. Reason why we need this
is that proper boundaries cannot be derived from mixed tests.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Jul 2017 22:00:22 +0000 (00:00 +0200)]
bpf: allow to specify log level and reduce it for test_verifier
For the test_verifier case, it's quite hard to parse log level 2 to
figure out what's causing an issue when used to log level 1. We do
want to use bpf_verify_program() in order to simulate some of the
tests with strict alignment. So just add an argument to pass the level
and put it to 1 for test_verifier.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 20 Jul 2017 22:00:21 +0000 (00:00 +0200)]
bpf: fix mixed signed/unsigned derived min/max value bounds
Edward reported that there's an issue in min/max value bounds
tracking when signed and unsigned compares both provide hints
on limits when having unknown variables. E.g. a program such
as the following should have been rejected:
... r1 carries an unsigned value, and is compared as unsigned
against a register carrying an immediate. Verifier deduces in
reg_set_min_max() that since the compare is unsigned and operation
is greater than (>), that in the fall-through/false case, r1's
minimum bound must be 0 and maximum bound must be r2. Latter is
larger than the bound and thus max value is reset back to being
'invalid' aka BPF_REGISTER_MAX_RANGE. Thus, r1 state is now
'R1=inv,min_value=0'. The subsequent test ...
11: (65) if r1 s> 0x1 goto pc+2
... is a signed compare of r1 with immediate value 1. Here,
verifier deduces in reg_set_min_max() that since the compare
is signed this time and operation is greater than (>), that
in the fall-through/false case, we can deduce that r1's maximum
bound must be 1, meaning with prior test, we result in r1 having
the following state: R1=inv,min_value=0,max_value=1. Given that
the actual value this holds is -8, the bounds are wrongly deduced.
When this is being added to r0 which holds the map_value(_adj)
type, then subsequent store access in above case will go through
check_mem_access() which invokes check_map_access_adj(), that
will then probe whether the map memory is in bounds based
on the min_value and max_value as well as access size since
the actual unknown value is min_value <= x <= max_value; commit fce366a9dd0d ("bpf, verifier: fix alu ops against map_value{,
_adj} register types") provides some more explanation on the
semantics.
It's worth to note in this context that in the current code,
min_value and max_value tracking are used for two things, i)
dynamic map value access via check_map_access_adj() and since
commit 06c1c049721a ("bpf: allow helpers access to variable memory")
ii) also enforced at check_helper_mem_access() when passing a
memory address (pointer to packet, map value, stack) and length
pair to a helper and the length in this case is an unknown value
defining an access range through min_value/max_value in that
case. The min_value/max_value tracking is /not/ used in the
direct packet access case to track ranges. However, the issue
also affects case ii), for example, the following crafted program
based on the same principle must be rejected as well:
Meaning, while we initialize the max_value stack slot that the
verifier thinks we access in the [1,2] range, in reality we
pass -7 as length which is interpreted as u32 in the helper.
Thus, this issue is relevant also for the case of helper ranges.
Resetting both bounds in check_reg_overflow() in case only one
of them exceeds limits is also not enough as similar test can be
created that uses values which are within range, thus also here
learned min value in r1 is incorrect when mixed with later signed
test to create a range:
This leaves us with two options for fixing this: i) to invalidate
all prior learned information once we switch signed context, ii)
to track min/max signed and unsigned boundaries separately as
done in [0]. (Given latter introduces major changes throughout
the whole verifier, it's rather net-next material, thus this
patch follows option i), meaning we can derive bounds either
from only signed tests or only unsigned tests.) There is still the
case of adjust_reg_min_max_vals(), where we adjust bounds on ALU
operations, meaning programs like the following where boundaries
on the reg get mixed in context later on when bounds are merged
on the dst reg must get rejected, too:
Meaning, in adjust_reg_min_max_vals() we must also reset range
values on the dst when src/dst registers have mixed signed/
unsigned derived min/max value bounds with one unbounded value
as otherwise they can be added together deducing false boundaries.
Once both boundaries are established from either ALU ops or
compare operations w/o mixing signed/unsigned insns, then they
can safely be added to other regs also having both boundaries
established. Adding regs with one unbounded side to a map value
where the bounded side has been learned w/o mixing ops is
possible, but the resulting map value won't recover from that,
meaning such op is considered invalid on the time of actual
access. Invalid bounds are set on the dst reg in case i) src reg,
or ii) in case dst reg already had them. The only way to recover
would be to perform i) ALU ops but only 'add' is allowed on map
value types or ii) comparisons, but these are disallowed on
pointers in case they span a range. This is fine as only BPF_JEQ
and BPF_JNE may be performed on PTR_TO_MAP_VALUE_OR_NULL registers
which potentially turn them into PTR_TO_MAP_VALUE type depending
on the branch, so only here min/max value cannot be invalidated
for them.
In terms of state pruning, value_from_signed is considered
as well in states_equal() when dealing with adjusted map values.
With regards to breaking existing programs, there is a small
risk, but use-cases are rather quite narrow where this could
occur and mixing compares probably unlikely.
Fixes: 484611357c19 ("bpf: allow access into map value arrays") Reported-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: avoid overflow of offset in ip6_find_1stfragopt
In some cases, offset can overflow and can cause an infinite loop in
ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and
cap it at IPV6_MAXPLEN, since packets larger than that should be invalid.
This problem has been here since before the beginning of git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 19 Jul 2017 17:46:59 +0000 (18:46 +0100)]
net: tehuti: don't process data if it has not been copied from userspace
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate CHANGEADDR event message is sent regardless of link
status whereas the setlink changes only generate a notification when
the link is up. Not sending a notification when the link is down breaks
dhcpcd which only processes hwaddr changes when the link is down.
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Hundebøll [Wed, 19 Jul 2017 06:17:02 +0000 (08:17 +0200)]
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
Commit f39908d3b1c45 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes: f39908d3b1c4 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10") Signed-off-by: Martin Hundebøll <mnhu@prevas.dk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
Add SoC specific compatibility strings to the Broadcom DTE
based PTP clock binding document.
Fixed the document heading and node name.
Fixes: 80d6076140b2 ("dt-binding: ptp: add bindings document for dte based ptp clock") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 18 Jul 2017 19:38:56 +0000 (22:38 +0300)]
netfilter: fix netfilter_net_init() return
We accidentally return an uninitialized variable.
Fixes: cf56c2f892a8 ("netfilter: remove old pre-netns era hook api") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Missing netlink message sanity check in nfnetlink, patch from
Mateusz Jurczyk.
2) We now have netfilter per-netns hooks, so let's kill global hook
infrastructure, this infrastructure is known to be racy with netns.
We don't care about out of tree modules. Patch from Florian Westphal.
3) find_appropriate_src() is buggy when colissions happens after the
conversion of the nat bysource to rhashtable. Also from Florian.
4) Remove forward chain in nf_tables arp family, it's useless and it is
causing quite a bit of confusion, from Florian Westphal.
5) nf_ct_remove_expect() is called with the wrong parameter, causing
kernel oops, patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 18 Jul 2017 09:57:55 +0000 (11:57 +0200)]
udp: preserve skb->dst if required for IP options processing
Eric noticed that in udp_recvmsg() we still need to access
skb->dst while processing the IP options.
Since commit 0a463c78d25b ("udp: avoid a cache miss on dequeue")
skb->dst is no more available at recvmsg() time and bad things
will happen if we enter the relevant code path.
This commit address the issue, avoid clearing skb->dst if
any IP options are present into the relevant skb.
Since the IP CB is contained in the first skb cacheline, we can
test it to decide to leverage the consume_stateless_skb()
optimization, without measurable additional cost in the faster
path.
v1 -> v2: updated commit message tags
Fixes: 0a463c78d25b ("udp: avoid a cache miss on dequeue") Reported-by: Andrey Konovalov <andreyknvl@google.com> Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
atm: zatm: Fix an error handling path in 'zatm_init_one()'
If 'dma_set_mask_and_coherent()' fails, we must undo the previous
'pci_request_regions()' call.
Adjust corresponding 'goto' to jump at the right place of the error
handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 58d607d3e52f ("tcp: provide skb->hash to synack packets") Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ppp: Fix false xmit recursion detect with two ppp devices
The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.
Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.
Fixes: 55454a565836 ("ppp: avoid dealock on recursive xmit") Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Signed-off-by: Liu Jianying <jianying.liu@ikuai8.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Mon, 17 Jul 2017 18:42:55 +0000 (11:42 -0700)]
bpf: check NULL for sk_to_full_sk() return value
When req->rsk_listener is NULL, sk_to_full_sk() returns
NULL too, so we have to check its return value against
NULL here.
Fixes: 40304b2a1567 ("bpf: BPF support for sock_ops") Reported-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Cc: Lawrence Brakmo <brakmo@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 15 Jul 2017 06:03:49 +0000 (23:03 -0700)]
jhash: fix -Wimplicit-fallthrough warnings
GCC 7 added a new -Wimplicit-fallthrough warning. It's only enabled
with W=1, but since linux/jhash.h is included in over hundred places
(including other global headers) it seems worthwhile fixing this
warning.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: expect: fix crash when putting uninited expectation
We crash in __nf_ct_expect_check, it calls nf_ct_remove_expect on the
uninitialised expectation instead of existing one, so del_timer chokes
on random memory address.
netfilter: nf_tables: only allow in/output for arp packets
arp packets cannot be forwarded.
They can be bridged, but then they can be filtered using
either ebtables or nftables bridge family.
The bridge netfilter exposes a "call-arptables" switch which
pushes packets into arptables, but lets not expose this for nftables, so better
close this asap.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When doing initial conversion to rhashtable I replaced the bucket
walk with a single rhashtable_lookup_fast().
When moving to rhlist I failed to properly walk the list of identical
tuples, but that is what is needed for this to work correctly.
The table contains the original tuples, so the reply tuples are all
distinct.
We currently decide that mapping is (not) in range only based on the
first entry, but in case its not we need to try the reply tuple of the
next entry until we either find an in-range mapping or we checked
all the entries.
This bug makes nat core attempt collision resolution while it might be
able to use the mapping as-is.
Mateusz Jurczyk [Wed, 7 Jun 2017 13:50:38 +0000 (15:50 +0200)]
netfilter: nfnetlink: Improve input length sanitization in nfnetlink_rcv
Verify that the length of the socket buffer is sufficient to cover the
nlmsghdr structure before accessing the nlh->nlmsg_len field for further
input sanitization. If the client only supplies 1-3 bytes of data in
sk_buff, then nlh->nlmsg_len remains partially uninitialized and
contains leftover memory from the corresponding kernel allocation.
Operating on such data may result in indeterminate evaluation of the
nlmsg_len < NLMSG_HDRLEN expression.
The bug was discovered by a runtime instrumentation designed to detect
use of uninitialized memory in the kernel. The patch prevents this and
other similar tools (e.g. KMSAN) from flagging this behavior in the future.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Two issues were observed in a review of the bcmgenet driver support for
fragmented SKBs which are addressed by this patch set.
The first addresses a problem that could occur if the driver is not able
to DMA map a fragment of the SKB. This would be a highly unusual event
but it would leave the hardware descriptors in an invalid state which
should be prevented.
The second is a hazard that could occur if the driver is able to reclaim
the first control block of a fragmented SKB before all of its fragments
have completed processing by the hardware. In this case the SKB could
be freed leading to reuse of memory that is still in use by hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.
This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.
It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bcmgenet: Fix unmapping of fragments in bcmgenet_xmit()
In case we fail to map a single fragment, we would be leaving the
transmit ring populated with stale entries.
This commit introduces the helper function bcmgenet_put_txcb()
which takes care of rewinding the per-ring write pointer back to
where we left.
It also consolidates the functionality of bcmgenet_xmit_single()
and bcmgenet_xmit_frag() into the bcmgenet_xmit() function to
make the unmapping of control blocks cleaner.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: Remove duplicate NSP Ethernet MAC binding document
Commit 07d4510f5251 ("dt-bindings: net: bgmac: add bindings documentation for
bgmac") added both brcm,amac-nsp.txt and brcm,bgmac-nsp.txt. The former is
actually the one that got updated and is in use by the bgmac driver while the
latter is duplicating the former and is not used nor updated.
Fixes: 07d4510f5251 ("dt-bindings: net: bgmac: add bindings documentation for bgmac") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11803 544 1 12348 303c isdn/hardware/avm/c4.o
File size After adding 'const':
text data bss dec hex filename
11931 416 1 12348 303c isdn/hardware/avm/c4.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
21656 1024 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o
File size After adding 'const':
text data bss dec hex filename
22424 256 96 22776 58f8 isdn/hardware/mISDN/hfcpci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
9963 1936 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o
File size After adding 'const':
text data bss dec hex filename
10091 1808 16 11915 2e8b isdn/hardware/mISDN/avmfritz.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13959 4080 24 18063 468f isdn/hardware/mISDN/w6692.o
File size After adding 'const':
text data bss dec hex filename
14087 3952 24 18063 468f isdn/hardware/mISDN/w6692.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
63450 1536 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o
File size After adding 'const':
text data bss dec hex filename
64698 288 1492 66478 103ae isdn/hardware/mISDN/hfcmulti.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10941 1776 16 12733 31bd isdn/hardware/mISDN/netjet.o
File size After adding 'const':
text data bss dec hex filename
11005 1712 16 12733 31bd isdn/hardware/mISDN/netjet.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6224 655 8 6887 1ae7 isdn/hardware/eicon/divasmain.o
File size After adding 'const':
text data bss dec hex filename
6608 271 8 6887 1ae7 isdn/hardware/eicon/divasmain.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5989 576 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o
File size After adding 'const':
text data bss dec hex filename
6085 480 0 6565 19a5 isdn/hisax/hisax_fcpcipnp.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10512 536 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o
File size After adding 'const':
text data bss dec hex filename
10672 376 4 11052 2b2c drivers/isdn/hisax/hfc4s8s_l1.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
13686 2064 4416 20166 4ec6 drivers/isdn/hisax/config.o
File size After adding 'const':
text data bss dec hex filename
15030 720 4416 20166 4ec6 drivers/isdn/hisax/config.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following behavior: for connections that had no RTT sample
at the time of initializing congestion control, BBR was initializing
the pacing rate to a high nominal rate (based an a guess of RTT=1ms,
in case this is LAN traffic). Then BBR never adjusted the pacing rate
downward upon obtaining an actual RTT sample, if the connection never
filled the pipe (e.g. all sends were small app-limited writes()).
This fix adjusts the pacing rate upon obtaining the first RTT sample.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_bbr: remove sk_pacing_rate=0 transient during init
Fix a corner case noticed by Eric Dumazet, where BBR's setting
sk->sk_pacing_rate to 0 during initialization could theoretically
cause packets in the sending host to hang if there were packets "in
flight" in the pacing infrastructure at the time the BBR congestion
control state is initialized. This could occur if the pacing
infrastructure happened to race with bbr_init() in a way such that the
pacer read the 0 rather than the immediately following non-zero pacing
rate.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to initialize the BBR pacing rate unconditionally,
based on the current cwnd and RTT estimate. This is a pure refactor,
but is needed for two following fixes.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to convert a BBR bandwidth and gain factor to a
pacing rate in bytes per second. This is a pure refactor, but is
needed for two following fixes.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In bbr_set_pacing_rate(), which decides whether to cut the pacing
rate, there was some code that considered exiting STARTUP to be
equivalent to the notion of filling the pipe (i.e.,
bbr_full_bw_reached()). Specifically, as the code was structured,
exiting STARTUP and going into PROBE_RTT could cause us to cut the
pacing rate down to something silly and low, based on whatever
bandwidth samples we've had so far, when it's possible that all of
them have been small app-limited bandwidth samples that are not
representative of the bandwidth available in the path. (The code was
correct at the time it was written, but the state machine changed
without this spot being adjusted correspondingly.)
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 14 Jul 2017 19:42:49 +0000 (12:42 -0700)]
openvswitch: Fix for force/commit action failures
When there is an established connection in direction A->B, it is
possible to receive a packet on port B which then executes
ct(commit,force) without first performing ct() - ie, a lookup.
In this case, we would expect that this packet can delete the existing
entry so that we can commit a connection with direction B->A. However,
currently we only perform a check in skb_nfct_cached() for whether
OVS_CS_F_TRACKED is set and OVS_CS_F_INVALID is not set, ie that a
lookup previously occurred. In the above scenario, a lookup has not
occurred but we should still be able to statelessly look up the
existing entry and potentially delete the entry if it is in the
opposite direction.
This patch extends the check to also hint that if the action has the
force flag set, then we will lookup the existing entry so that the
force check at the end of skb_nfct_cached has the ability to delete
the connection.
Fixes: dd41d330b03 ("openvswitch: Add force commit.") CC: Pravin Shelar <pshelar@nicira.com> CC: dev@openvswitch.org Signed-off-by: Joe Stringer <joe@ovn.org> Signed-off-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago David Woodhouse reported skb_under_panic
when we try to push ethernet header to fragmented ipv6 skbs.
It was fixed for ipv6 by Florian Westphal in
commit 1d325d217c7f ("ipv6: ip6_fragment: fix headroom tests and skb leak")
However similar problem still exist in ipv4.
It does not trigger skb_under_panic due paranoid check
in ip_finish_output2, however according to Alexey Kuznetsov
current state is abnormal and ip_fragment should be fixed too.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.
Cc: Joe Jin <joe.jin@oracle.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ioc3-eth: store pointer to net_device for priviate area
Computing the alignment manually for going from priv to pub is probably
not such a good idea, and in general the assumption that going from priv
to pub is possible trivially could change, so rather than relying on
that, we change things to just store a pointer to pub. This was sugested
by DaveM in [1].
Abhishek Shah [Thu, 13 Jul 2017 19:04:09 +0000 (00:34 +0530)]
Documentation: devicetree: net: optional idm regs for bgmac
Specifying IDM register space in DT is not mendatory for SoCs
where firmware takes care of IDM operations. This patch updates
BGMAC driver's DT binding documentation indicating the same.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Oza Oza <oza.oza@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Abhishek Shah [Thu, 13 Jul 2017 19:04:08 +0000 (00:34 +0530)]
net: ethernet: bgmac: Make IDM register space optional
IDM operations are usually one time ops and should be done in
firmware itself. Driver is not supposed to touch IDM registers.
However, for some SoCs', driver is performing IDM read/writes.
So this patch masks IDM operations in case firmware is taking
care of IDM operations.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com> Reviewed-by: Oza Oza <oza.oza@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Abhishek Shah [Thu, 13 Jul 2017 19:04:07 +0000 (00:34 +0530)]
net: ethernet: bgmac: Remove unnecessary 'return' from platform_bgmac_idm_write
Return type for idm register write callback should be void as 'writel'
API is used for write operation. However, there no need to have 'return'
in this function.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com> Reviewed-by: Oza Oza <oza.oza@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 14 Jul 2017 14:07:33 +0000 (22:07 +0800)]
sctp: fix an array overflow when all ext chunks are set
Marcelo noticed an array overflow caused by commit c28445c3cb07
("sctp: add reconf_enable in asoc ep and netns"), in which sctp
would add SCTP_CID_RECONF into extensions when reconf_enable is
set in sctp_make_init and sctp_make_init_ack.
Then now when all ext chunks are set, 4 ext chunk ids can be put
into extensions array while extensions array size is 3. It would
cause a kernel panic because of this overflow.
This patch is to fix it by defining extensions array size is 4 in
both sctp_make_init and sctp_make_init_ack.
Fixes: c28445c3cb07 ("sctp: add reconf_enable in asoc ep and netns") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
liquidio: fix possible eeprom format string overflow
gcc reports that the temporary buffer for computing the
string length may be too small here:
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'lio_get_eeprom_len':
/drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:21: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:345:6: note: 'sprintf' output between 35 and 167 bytes into a destination of size 128
len = sprintf(buf, "boardname:%s serialnum:%s maj:%lld min:%lld\n",
This extends it to 192 bytes, which is certainly enough. As far
as I could tell, there are no other constraints that require a specific
maximum size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 notices that "-event-%d" could be more than 11 characters long
if we had larger 'vector' numbers:
drivers/net/vmxnet3/vmxnet3_drv.c: In function 'vmxnet3_activate_dev':
drivers/net/vmxnet3/vmxnet3_drv.c:2095:40: error: 'sprintf' may write a terminating nul past the end of the destination [-Werror=format-overflow=]
sprintf(intr->event_msi_vector_name, "%s-event-%d",
^~~~~~~~~~~~~
drivers/net/vmxnet3/vmxnet3_drv.c:2095:3: note: 'sprintf' output between 9 and 33 bytes into a destination of size 32
The current code is safe, but making the string a little longer
is harmless and lets gcc see that it's ok.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: thunder_bgx: avoid format string overflow warning
gcc warns that the temporary buffer might be too small here:
drivers/net/ethernet/cavium/thunder/thunder_bgx.c: In function 'bgx_probe':
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: error: '%d' directive writing between 1 and 10 bytes into a region of size between 9 and 11 [-Werror=format-overflow=]
sprintf(str, "BGX%d LMAC%d mode", bgx->bgx_id, lmacid);
^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:16: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/cavium/thunder/thunder_bgx.c:1020:3: note: 'sprintf' output between 16 and 27 bytes into a destination of size 20
This probably can't happen, but it can't hurt to make it long
enough for the theoretical limit.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
gcc notices that large queue numbers would overflow the queue name
string:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c: In function 'bnx2x_get_strings':
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:25: note: directive argument in the range [0, 2147483647]
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3165:5: note: 'sprintf' output between 2 and 11 bytes into a destination of size 5
There is a hard limit in place that makes the number at most two
digits, so the code is fine. This changes it to use snprintf()
to truncate instead of overflowing, which shuts up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for the port_name string that might be longer than
six characters if we had more than 10 ports:
drivers/net/ethernet/sun/niu.c: In function 'niu_put_parent':
drivers/net/ethernet/sun/niu.c:9563:21: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9563:21: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9563:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(port_name, "port%d", port);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sun/niu.c: In function 'niu_pci_init_one':
drivers/net/ethernet/sun/niu.c:9538:22: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(port_name, "port%d", port);
^~~~~~~~
drivers/net/ethernet/sun/niu.c:9538:22: note: directive argument in the range [0, 255]
drivers/net/ethernet/sun/niu.c:9538:3: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
While we know that the port number is small, there is no harm in
making the format string two bytes longer to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
One string we pass into the cs->info buffer might be too long,
as pointed out by gcc:
drivers/isdn/divert/isdn_divert.c: In function 'll_callback':
drivers/isdn/divert/isdn_divert.c:488:22: error: '%d' directive writing between 1 and 3 bytes into a region of size between 1 and 69 [-Werror=format-overflow=]
sprintf(cs->info, "%d 0x%lx %s %s %s %s 0x%x 0x%x %d %d %s\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/divert/isdn_divert.c:488:22: note: directive argument in the range [0, 255]
drivers/isdn/divert/isdn_divert.c:488:4: note: 'sprintf' output 25 or more bytes (assuming 129) into a destination of size 90
This is unlikely to actually cause problems, so let's use snprintf
as a simple workaround to shut up the warning and truncate the
buffer instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 13 Jul 2017 20:45:41 +0000 (15:45 -0500)]
net: qcom/emac: fix double free of SGMII IRQ during shutdown
If the interface is not up, then don't try to close it during a
shutdown. This avoids possible double free of the IRQ, which
can happen during a shutdown.
Fixes: 03eb3eb4d4d5 ("net: qcom/emac: add shutdown function") Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Kulhavy [Thu, 13 Jul 2017 17:40:57 +0000 (19:40 +0200)]
smsc95xx: use ethtool_op_get_ts_info()
This change enables the use of SW timestamping on Raspberry PI.
smsc95xx uses the usbnet transmit function usbnet_start_xmit(), which
implements software timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE
capability was missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced.
By using ethtool_op_get_ts_info() as get_ts_info() also the
SOF_TIMESTAMPING_TX_SOFTWARE is announced.
Signed-off-by: Petr Kulhavy <brain@jikos.cz> Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When PACKET_QDISC_BYPASS is not used, Tx queue selection will be done
before the packet is enqueued, taking into account any mappings set by
a queuing discipline such as mqprio without hardware offloading. This
selection may be affected by a previously saved queue_mapping, either on
the Rx path, or done before the packet reaches the device, as it's
currently the case for AF_PACKET.
In order for queue selection to work as expected when using traffic
control, there can't be another selection done before that point is
reached, so move the call to packet_pick_tx_queue to
packet_direct_xmit, leaving the default xmit path as it was before
PACKET_QDISC_BYPASS was introduced.
A forward declaration of packet_pick_tx_queue() is introduced to avoid
the need to reorder the functions within the file.
Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Iván Briano <ivan.briano@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix dest lookup when vlan proto doesn't match
With 802.1ad support the vlan_ingress code started checking for vlan
protocol mismatch which causes the current tag to be inserted and the
bridge vlan protocol & pvid to be set. The vlan tag insertion changes
the skb mac_header and thus the lookup mac dest pointer which was loaded
prior to calling br_allowed_ingress in br_handle_frame_finish is VLAN_HLEN
bytes off now, pointing to the last two bytes of the destination mac and
the first four of the source mac causing lookups to always fail and
broadcasting all such packets to all ports. Same thing happens for locally
originated packets when passing via br_dev_xmit. So load the dest pointer
after the vlan checks and possible skb change.
Fixes: 8580e2117c06 ("bridge: Prepare for 802.1ad vlan filtering support") Reported-by: Anitha Narasimha Murthy <anitha@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only support DT method to control xge led.
This patch is the implementation of acpi method to control xge led.
Signed-off-by: LiuJian <liujian56@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Reviewed-by: Daode Huang <huangdaode@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Wed, 12 Jul 2017 22:56:41 +0000 (15:56 -0700)]
netpoll: shut up a kernel warning on refcount
When we convert atomic_t to refcount_t, a new kernel warning
on "increment on 0" is introduced in the netpoll code,
zap_completion_queue(). In fact for this special case, we know
the refcount is 0 and we just have to set it to 1 to satisfy
the following dev_kfree_skb_any(), so we can just use
refcount_set(..., 1) instead.
Fixes: 633547973ffc ("net: convert sk_buff.users from atomic_t to refcount_t") Reported-by: Dave Jones <davej@codemonkey.org.uk> Cc: Reshetova, Elena <elena.reshetova@intel.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cdc_ncm: Set NTB format again after altsetting switch for Huawei devices
Some firmwares in Huawei E3372H devices have been observed to switch back
to NTB 32-bit format after altsetting switch.
This patch implements a driver flag to check for the device settings and
set NTB format to 16-bit again if needed.
The flag has been activated for devices controlled by the huawei_cdc_ncm.c
driver.
V1->V2:
- fixed broken error checks
- some corrections to the commit message
V2->V3:
- variable name changes, to clarify what's happening
- check (and possibly set) the NTB format later in the common bind code path
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> Reported-and-tested-by: Christian Panton <christian@panton.org> Reviewed-by: Bjørn Mork <bjorn@mork.no> CC: Bjørn Mork <bjorn@mork.no> CC: Christian Panton <christian@panton.org> CC: linux-usb@vger.kernel.org CC: netdev@vger.kernel.org CC: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
mdio: mux: fix parsing mux registers outside of the PHY address range
mdio_mux_init parses the child nodes of the MDIO mux. When using
"mdio-mux-mmioreg" the child nodes are describing the register value
that is written to switch between the MDIO busses.
The change which makes the error messages more verbose changed the
parsing of the "reg" property from a simple of_property_read_u32 call
to of_mdio_parse_addr. On a Khadas VIM (based on the Meson GXL SoC,
which uses mdio-mux-mmioreg) this prevents registering the MDIO mux
(because the "reg" values on the MDIO mux child nodes are 0x2009087f
and 0xe40908ff) and leads to the following errors:
mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff PHY address -469169921 is too large
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@e40908ff
mdio-mux-mmioreg c883455c.eth-phy-mux: /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f PHY address 537462911 is too large
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: Failed to find reg for child /soc/periphs@c8834000/eth-phy-mux/mdio@2009087f
mdio-mux-mmioreg c883455c.eth-phy-mux: Error: No acceptable child buses found
mdio-mux-mmioreg c883455c.eth-phy-mux: failed to register mdio-mux bus /soc/periphs@c8834000/eth-phy-mux
(as a result of that ethernet is not working, because the PHY which is
connected through the mux' child MDIO bus, which is not being
registered).
Fix this by reverting the change from of_mdio_parse_addr to
of_mdio_parse_addr.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 13 Jul 2017 20:36:40 +0000 (13:36 -0700)]
net: set fib rule refcount after malloc
The configure callback of fib_rules_ops can change the refcnt of a
fib rule. For instance, mlxsw takes a refcnt when adding the processing
of the rule to a work queue. Thus the rule refcnt can not be reset to
to 1 afterwards. Move the refcnt setting to after the allocation.
Fixes: 5361e209dd30 ("net: avoid one splat in fib_nl_delrule()") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 11 Jul 2017 11:47:33 +0000 (12:47 +0100)]
rt2x00: make const array glrt_table static
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 11 Jul 2017 10:52:23 +0000 (11:52 +0100)]
net: broadcom: bnx2x: make a couple of const arrays static
Don't populate various tables on the stack but make them static const.
Makes the object code smaller by nearly 200 bytes:
Before:
text data bss dec hex filename
113468 11200 0 124668 1e6fc bnx2x_ethtool.o
After:
text data bss dec hex filename
113129 11344 0 124473 1e639 bnx2x_ethtool.o
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xgene: Don't fail probe, if there is no clk resource for SGMII interfaces
This change fixes following problem
[ 1.827940] xgene-enet: probe of 1f210030.ethernet failed with error -2
which leads to a missing ethernet interface (reproducable at least on
Gigabyte MP30-AR0 and APM Mustang systems).
The check for a valid clk resource fails, because DT doesn't provide a
clock for sgenet1. But the driver doesn't use this clk, if the ethernet
port is connected via SGMII. Therefore this patch avoids probing for clk
on SGMII interfaces.
Fixes: 9aea7779b764 ("drivers: net: xgene: Fix crash on DT systems") Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Kefeng Wang [Thu, 13 Jul 2017 06:27:58 +0000 (14:27 +0800)]
bpf: fix return in bpf_skb_adjust_net
The bpf_skb_adjust_net() ignores the return value of bpf_skb_net_shrink/grow,
and always return 0, fix it by return 'ret'.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
I made the mistake of upgrading my desktop to the new Fedora 26 that
comes with gcc-7.1.1.
There's nothing wrong per se that I've noticed, but I now have 1500
lines of warnings, mostly from the new format-truncation warning
triggering all over the tree.
We use 'snprintf()' and friends in a lot of places, and often know that
the numbers are fairly small (ie a controller index or similar), but gcc
doesn't know that, and sees an 'int', and thinks that it could be some
huge number. And then complains when our buffers are not able to fit
the name for the ten millionth controller.
These warnings aren't necessarily bad per se, and we probably want to
look through them subsystem by subsystem, but at least during the merge
window they just mean that I can't even see if somebody is introducing
any *real* problems when I pull.
Merge tag 'modules-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules updates from Jessica Yu:
"Summary of modules changes for the 4.13 merge window:
- Minor code cleanups
- Avoid accessing mod struct prior to checking module struct version,
from Kees
- Fix racy atomic inc/dec logic of kmod_concurrent_max in kmod, from
Luis"
* tag 'modules-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: make the modinfo name const
kmod: reduce atomic operations on kmod_concurrent and simplify
module: use list_for_each_entry_rcu() on find_module_all()
kernel/module.c: suppress warning about unused nowarn variable
module: Add module name to modinfo
module: Pass struct load_info into symbol checks
net: stmmac: revert "support future possible different internal phy mode"
Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode")
Fixes: 1c2fa5f84683 ("net: stmmac: support future possible different internal phy mode") Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes: 12fb0da45c9a ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This work from Amir introduces the inodes index feature, which
provides:
- hardlinks are not broken on copy up
- infrastructure for overlayfs NFS export
This also fixes constant st_ino for samefs case for lower hardlinks"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (33 commits)
ovl: mark parent impure and restore timestamp on ovl_link_up()
ovl: document copying layers restrictions with inodes index
ovl: cleanup orphan index entries
ovl: persistent overlay inode nlink for indexed inodes
ovl: implement index dir copy up
ovl: move copy up lock out
ovl: rearrange copy up
ovl: add flag for upper in ovl_entry
ovl: use struct copy_up_ctx as function argument
ovl: base tmpfile in workdir too
ovl: factor out ovl_copy_up_inode() helper
ovl: extract helper to get temp file in copy up
ovl: defer upper dir lock to tempfile link
ovl: hash overlay non-dir inodes by copy up origin
ovl: cleanup bad and stale index entries on mount
ovl: lookup index entry for copy up origin
ovl: verify index dir matches upper dir
ovl: verify upper root dir matches lower root dir
ovl: introduce the inodes index dir feature
ovl: generalize ovl_create_workdir()
...
Al Viro [Wed, 12 Jul 2017 03:59:45 +0000 (04:59 +0100)]
fix a braino in compat_sys_getrlimit()
Reported-and-tested-by: Meelis Roos <mroos@linux.ee> Fixes: commit d9e968cb9f84 "getrlimit()/setrlimit(): move compat to native" Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
brcmfmac: fix possible buffer overflow in brcmf_cfg80211_mgmt_tx()
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
net: hns: Bugfix for Tx timeout handling in hns driver
When hns port type is not debug mode, netif_tx_disable is called
when there is a tx timeout, which requires system reboot to return
to normal state. This patch fix this problem by resetting the net
dev.
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support") Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 12 Jul 2017 07:56:47 +0000 (10:56 +0300)]
net: ipmr: ipmr_get_table() returns NULL
The ipmr_get_table() function doesn't return error pointers it returns
NULL on error.
Fixes: 4f75ba6982bc ("net: ipmr: Add ipmr_rtm_getroute") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 12 Jul 2017 07:42:06 +0000 (10:42 +0300)]
nfp: freeing the wrong variable
We accidentally free a NULL pointer and leak the pointer we want to
free. Also you can tell from the label name what was intended. :)
Fixes: abfcdc1de9bf ("nfp: add a stats handler for flower offloads") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 12 Jul 2017 15:15:52 +0000 (08:15 -0700)]
Merge branch 'mlxsw-spectrum-Various-fixes'
Jiri Pirko says:
====================
mlxsw: spectrum: Various fixes
First patch adds a missing rollback in error path. Second patch prevents
a use-after-free during IPv4 route replace. Last two patches fix warnings
from static checkers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log