Bart Van Assche [Thu, 30 Oct 2014 13:48:30 +0000 (14:48 +0100)]
IB/srp: Separate target and channel variables
Changes in this patch:
- Move channel variables into a new structure (struct srp_rdma_ch).
- Add an srp_target_port pointer, 'lock' and 'comp_vector' members
in struct srp_rdma_ch.
- Add code to initialize these three new member variables.
- Many boring "target->" into "ch->" changes.
- The cm_id and completion handler context pointers are now of type
srp_rdma_ch * instead of srp_target_port *.
- Three kzalloc(a * b, f) calls have been changed into kcalloc(a, b, f)
to avoid that this patch would trigger a checkpatch warning.
- Two casts from u64 into unsigned long long have been left out
because these are superfluous. Since considerable time u64 is
defined as unsigned long long for all architectures supported by
the Linux kernel.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:48:05 +0000 (14:48 +0100)]
IB/srp: Introduce two new srp_target_port member variables
Introduce the srp_target_port member variables 'sgid' and 'pkey'.
Change the type of 'orig_dgid' from __be16[8] into union ib_gid.
This patch does not change any functionality but makes the
"Separate target and channel variables" patch easier to verify.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:47:22 +0000 (14:47 +0100)]
IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning
If a cable is pulled during LUN scanning it can happen that the
SRP rport and the SCSI host have been created but no LUNs have been
added to the SCSI host. Since multipathd only sends SCSI commands
to a SCSI target if one or more SCSI devices are present and since
there is no keepalive mechanism for IB queue pairs this means that
after a LUN scan failed and after a reconnect has succeeded no
data will be sent over the QP and hence that a subsequent cable
pull will not be detected. Avoid this by not creating an rport or
SCSI host if a cable is pulled during a SCSI LUN scan.
Note: so far the above behavior has only been observed with the
kernel module parameter ch_count set to a value >= 2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:46:55 +0000 (14:46 +0100)]
IB/srp: Remove stale connection retry mechanism
Attempting to connect three times may be insufficient after an
initiator system tries to relogin, especially if the relogin
attempt occurs before the SRP target service ID has been
registered. Since the srp_daemon retries a failed login attempt
anyway, remove the stale connection retry mechanism.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:46:27 +0000 (14:46 +0100)]
IB/srp: Move ib_destroy_cm_id() call into srp_free_ch_ib()
The patch that adds multichannel support into the SRP initiator
driver introduces an additional call to srp_free_ch_ib(). This
patch helps to keep that later patch simple.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Chen Gang [Sat, 1 Nov 2014 11:46:12 +0000 (19:46 +0800)]
qla2xxx: remove redundant declaration in 'qla_gbl.h'
Remove 2 redundant extern inline functions: qla8044_set_qsnt_ready() and
qla8044_need_reset_handler(). At present, within upstream next kernel
source code, they are only used within "drivers/scsi/qla2xxx/qla_nx2.c".
The related error and warnings (with allmodconfig under tile):
CC [M] drivers/scsi/qla2xxx/qla_nx2.o
drivers/scsi/qla2xxx/qla_nx2.c:1633:1: error: static declaration of 'qla8044_need_reset_handler' follows non-static declaration
qla8044_need_reset_handler(struct scsi_qla_host *vha)
^
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_nx2.c:11:
drivers/scsi/qla2xxx/qla_gbl.h:756:20: note: previous declaration of 'qla8044_need_reset_handler' was here
extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha);
^
drivers/scsi/qla2xxx/qla_gbl.h:756:20: warning: inline function 'qla8044_need_reset_handler' declared but never defined
make[3]: *** [drivers/scsi/qla2xxx/qla_nx2.o] Error 1
make[2]: *** [drivers/scsi/qla2xxx] Error 2
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
CC [M] drivers/scsi/qla2xxx/qla_tmpl.o
In file included from drivers/scsi/qla2xxx/qla_def.h:3706:0,
from drivers/scsi/qla2xxx/qla_tmpl.c:7:
drivers/scsi/qla2xxx/qla_gbl.h:755:20: warning: inline function 'qla8044_set_qsnt_ready' declared but never defined
extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Thu, 2 Oct 2014 07:21:41 +0000 (09:21 +0200)]
vmw_pvscsi: fixup tagging
The request (and SCSI command) tag is the tag number assigned
by the generic block-tagging code, not the SCSI-II tag messages.
Those are represented by the device flags 'tagged_supported',
'simple_tags', and 'ordered_tags'.
(The SCSI midlayer doesn't use HEAD_OF_QUEUE tags).
So fixup vmw_pvscsi to assign the correct tag type.
[hch: fixed up to never set MSG_ORDERED_TAG] Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Arvind Kumar <arvindkumar@vmware.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we also get proper values in cmd->request->tag for untagged
commands, there is no need to force tagged_supported to on in drivers
that need host-wide tags.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi: don't set tagging state from scsi_adjust_queue_depth
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
mptfusion: don't change queue type in ->change_queue_depth
This function shouldn't change the queue type, just the depth.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Unless we want to build a SPI tag message we should just check SCMD_TAGGED
instead of reverse engineering a tag type through the use of
scsi_populate_tag_msg.
Also rename the function to spi_populate_tag_msg, make it behave like the
other spi message helpers, and move it to the spi transport class.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: add new scsi-command flag for tagged commands
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi_dh: get module reference outside of device handler
We need to grab a reference to the module before calling the attach
routines to avoid a small race vs module removal. It also cleans up
the code significantly as a side effect.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Hannes Reinecke <hare@suse.de>
The T10 SBC UNMAP command does not provide any hard guarantees that
blocks will return zeroes on a subsequent READ. This is due to the fact
that the device server is free to silently ignore all or parts of the
request.
The only way to ensure that a block consistently returns zeroes after
being unmapped is to use WRITE SAME with the UNMAP bit set. Should the
device be unable to unmap one or more blocks described by the command it
is required to manually write zeroes to them.
Until now we have preferred UNMAP over the WRITE SAME variants to
accommodate thinly provisioned devices that predated the final SBC-3
spec. This patch changes the heuristic so that we favor WRITE SAME(16)
or (10) over UNMAP if these commands are marked as supported in the
Logical Block Provisioning VPD page.
The patch also disables discard_zeroes_data for devices operating in
UNMAP mode.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
The calling conventions for this function are bad as it could return
-ENODEV both for a device not currently online and a not recognized ioctl.
Add a new scsi_ioctl_block_when_processing_errors function that wraps
scsi_block_when_processing_errors with the a special case for the
SG_SCSI_RESET ioctl command, and handle the SG_SCSI_RESET case itself
in scsi_ioctl. All callers of scsi_ioctl now must call the above helper
to check for the EH state, so that the ioctl handler itself doesn't
have to.
Reported-by: Robert Elliott <Elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Bart Van Assche [Thu, 30 Oct 2014 13:46:00 +0000 (14:46 +0100)]
scsi: add support for multiple hardware queues in scsi_(host_)find_tag
Modify scsi_find_tag() and scsi_host_find_tag() such that these
functions can translate a tag generated by blk_mq_unique_tag().
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:45:36 +0000 (14:45 +0100)]
scsi: add support for multiple hardware queues
Allow a SCSI LLD to declare how many hardware queues it supports
by setting Scsi_Host.nr_hw_queues before calling scsi_add_host().
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Bart Van Assche [Thu, 30 Oct 2014 13:45:11 +0000 (14:45 +0100)]
blk-mq: add blk_mq_unique_tag()
The queuecommand() callback functions in SCSI low-level drivers
need to know which hardware context has been selected by the
block layer. Since this information is not available in the
request structure, and since passing the hctx pointer directly to
the queuecommand callback function would require modification of
all SCSI LLDs, add a function to the block layer that allows to
query the hardware context index.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Acked-by: Jens Axboe <axboe@kernel.dk> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:07 +0000 (14:27 +0200)]
scsi: ratelimit I/O error messages
There can be quite a lot of I/O error messages, even on smaller
machines. So we need to ratelimit them to not overwhelm logging.
Signed-off-by: Hannes Reinecke <hare@suse.de> Tested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Thu, 30 Oct 2014 08:44:36 +0000 (09:44 +0100)]
scsi: correct return values for .eh_abort_handler implementations
The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: Robert Elliott <elliott@hp.com> Cc: <stable@vger.kernel.org> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:04 +0000 (14:27 +0200)]
scsi: document scsi_try_to_abort_cmd
scsi_try_to_abort_cmd() should only return SUCCESS, FAILED, or
FAST_IO_FAIL. So document that in the function description and simplify
the logging message.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Christoph Hellwig <hch@infradead.org> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:03 +0000 (14:27 +0200)]
scsi: use shost argument in scsi_eh_prt_fail_stats
The EH statistics are per host, so we should be using
shost_printk() here.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:02 +0000 (14:27 +0200)]
scsi: fixup logging messages in scsi_error.c
Use the matching scope for logging messages to allow for
better command tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de> Suggested-by: Robert Elliott <elliott@hp.com> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:27:00 +0000 (14:27 +0200)]
scsi: remove scsi_show_result()
Open-code scsi_print_result in sd.c, and cleanup logging to
not print duplicate informations.
Also remove the call to scsi_show_result() in ufshcd.c
to be consistent with other callers of scsi_execute().
With that we can remove scsi_show_result in constants.c
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:57 +0000 (14:26 +0200)]
scsi: repurpose the last argument from print_opcode_name()
print_opcode_name() was only ever called with a '0' argument
from LLDDs and ULDs which were _not_ supporting variable length
CDBs, so the 'if' clause was never triggered.
Instead we should be using the last argument to specify
the cdb length to avoid accidental overflow when reading
the cdb buffer.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:51 +0000 (14:26 +0200)]
scsi: do not decode sense extras
Currently we're only decoding sense extras for tape devices.
And even there only for fixed format sense formats.
As this is of rather limited use in the general case we should
be stop trying to decode sense extras; the tape driver does
its own decoding anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:50 +0000 (14:26 +0200)]
scsi: stop decoding if scsi_normalize_sense() fails
If scsi_normalize_sense() fails we couldn't decode the sense
buffer, and the scsi_sense_hdr fields are invalid.
For those cases we should rather dump the sense buffer
and not try to decode invalid fields.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:49 +0000 (14:26 +0200)]
53c700: remove scsi_print_sense() usage
The 53c700 driver would be using scsi_print_sense() in a debug
statement, which was never compiled in. Plus the same information
can get retrieved with logging. So remove it.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:47 +0000 (14:26 +0200)]
fas216: return DID_ERROR for incomplete data transfer
fas216 returns DID_BAD_TARGET for an incomplete data
transfer. The midlayer uses DID_BAD_TARGET to signal
a non-existing or not reachable target. So we should
rather be using DID_ERROR here.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:46 +0000 (14:26 +0200)]
acornscsi: use scsi_print_command()
Update acornscsi to use scsi_print_command() instead of the
underscore version and use scmd_printk() in acornscsi_done().
This will add correct device annotations in the resulting message.
And we should be using set_host_byte() for setting the
final result.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:45 +0000 (14:26 +0200)]
scsi: use sdev as argument for sense code printing
We should be using the standard dev_printk() variants for
sense code printing.
[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter] Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Hannes Reinecke [Fri, 24 Oct 2014 12:26:43 +0000 (14:26 +0200)]
aha152x: debug output update and whitespace cleanup
Remove all uncommented debugging code and move all
printk() statements over to dev_printk().
And while we're at it we should be doing a whitespace
cleanup, too.
Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Some SES devices give non-unique Element Descriptors as part of the
Element Descriptor diag page. Since we use these for creating sysfs
entries, they need to be unique. The specification doesn't require
these to be unique.
Eg:
$ sg_ses -p 7 /dev/sg0
FTS CORP TXS6_SAS20BPX12 0500
enclosure services device
Element descriptor In diagnostic page:
generation code: 0x0
element descriptor by type list
Element type: Array device, subenclosure id: 0
Overall descriptor: ArrayDevicesInSubEnclsr0
Element 1 descriptor: ArrayDevice00
Element 2 descriptor: ArrayDevice01
Element 3 descriptor: ArrayDevice02
Element 4 descriptor: ArrayDevice03
Element 5 descriptor: ArrayDevice03
Element 6 descriptor: ArrayDevice03
Element 7 descriptor: ArrayDevice03
Element 8 descriptor: ArrayDevice03
Element 9 descriptor: ArrayDevice03
Element 10 descriptor: ArrayDevice03
Element 11 descriptor: ArrayDevice03
Element 12 descriptor: ArrayDevice03
Based on http://thread.gmane.org/gmane.linux.scsi/69289. This
version implements James' ideas about the naming convention
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de> Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Laurence Oberman [Sun, 19 Oct 2014 13:44:25 +0000 (09:44 -0400)]
st: add a debug_flag module parameter request
This patch adds a debug_flag parameter that can be set on module load, and allows the DEBUG facility without a module recompile.
Note that now DEBUG 1 is the default with this patch.
Usage: modprobe st debug_flag=1
Signed-off-by: Laurence Oberman <loberman@redhat.com> Acked-by: Kai M??kisara <kai.makisara@kolumbus.fi> Signed-off-by: Christoph Hellwig <hch@lst.de>
Douglas Gilbert [Sat, 18 Oct 2014 20:11:21 +0000 (22:11 +0200)]
scsi: add SG_SCSI_RESET_NO_ESCALATE flag to SG_SCSI_RESET ioctl
Further to a January 2013 thread titled: "[PATCH] SG_SCSI_RESET ioctl
should only perform requested operation" by Jeremy Linton a patch (v3)
is presented that expands the existing ioctl to include "no_escalate"
versions to the existing resets. This requires no changes to SCSI low
level drivers (LLDs); it adds several more finely tuned reset options
to the user space. For example:
/* This call remains the same, with the same escalating semantics
* if the device (LU) reset fail. That is: on failure to try a
* target reset and if that fails, try a bus reset, and if that fails
* try a host (i.e. LLD) reset. */
val = SG_SCSI_RESET_DEVICE;
res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
/* What follows is a new option introduced by this patch series. Only
* a device reset is attempted. If that fails then an appropriate
* error code is provided. N.B. There is no reset escalation. */
val = SG_SCSI_RESET_DEVICE | SG_SCSI_RESET_NO_ESCALATE;
res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Jeremy Linton <jlinton@tributary.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
As sparse correctly pointed out, scsi_partsize should use get_unaligned_le32
to read PC partition tables from disk, as they are little endian.
The result of this bug is that we returned incorrect geometries on big
endian systems when using the scsicam variant. Which probably doesn't
matter as only old x86 systems every cared about the geometry.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
Mark Rustad [Tue, 14 Oct 2014 13:38:53 +0000 (06:38 -0700)]
scsi: resolve some missing-field-initializers warnings
Resolve some missing-field-initializers warnings by using
designated initialization.
[hch: W=2 with modern gcc warns about this. Pretty pointless to me, but
I'd prefer to keep us warning free]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark Knibbs [Thu, 9 Oct 2014 11:39:48 +0000 (12:39 +0100)]
scsi: fix off-by-one LUN check in scsi_scan_host_selected()
The Scsi_Host structure max_lun field is the maximum allowed LUN plus 1. So
a LUN value is invalid if >= max_lun.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark Knibbs [Thu, 9 Oct 2014 11:39:40 +0000 (12:39 +0100)]
scsi: fix trivial typos in scsi_scan.c comment
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
bnx2fc_queuecommand(): when allocating a new io_req, the tgt_lock
spinlock must be locked before calling bnx2fc_cmd_alloc().
The spinlock should also be kept locked until bnx2fc_post_io_req() has
been completed.
If not, a kernel thread may call bnx2fc_process_cq_compl() that extracts
the newly allocated io_req from hba->cmd_mgr->cmds and destroys it while
it is still being used by bnx2fc_post_io_req().
Jiang Liu [Mon, 3 Nov 2014 12:44:20 +0000 (20:44 +0800)]
megaraid_sas: fix bug in handling return value of pci_enable_msix_range()
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 4ae93043e3a3 "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()" Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com> Acked-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> # 3.17
scsi: TUR path is down after adapter gets reset with multipath
This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de>
Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler. Since commit 1a789310f54502fde057a133ab5b61cce6 we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.
Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org> Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi: only re-lock door after EH on devices that were reset
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Cc: stable@vger.kernel.org Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Meelis Roos <meelis.roos@ut.ee> Tested-by: Meelis Roos <meelis.roos@ut.ee> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Linus Torvalds [Sun, 9 Nov 2014 22:49:56 +0000 (14:49 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Linus Torvalds [Sun, 9 Nov 2014 22:46:36 +0000 (14:46 -0800)]
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Linus Torvalds [Sun, 9 Nov 2014 22:30:24 +0000 (14:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Linus Torvalds [Sun, 9 Nov 2014 22:11:58 +0000 (14:11 -0800)]
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Linus Torvalds [Sun, 9 Nov 2014 22:11:07 +0000 (14:11 -0800)]
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sun, 9 Nov 2014 22:07:30 +0000 (14:07 -0800)]
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Linus Torvalds [Sun, 9 Nov 2014 22:05:53 +0000 (14:05 -0800)]
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
Andreas Färber [Thu, 6 Nov 2014 17:22:10 +0000 (18:22 +0100)]
ARM: dts: zynq: Enable PL clocks for Parallella
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Nov 2014 17:32:29 +0000 (09:32 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Linus Torvalds [Sat, 8 Nov 2014 02:08:02 +0000 (18:08 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Linus Torvalds [Fri, 7 Nov 2014 22:08:13 +0000 (14:08 -0800)]
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Linus Torvalds [Fri, 7 Nov 2014 19:55:47 +0000 (11:55 -0800)]
Merge tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Linus Torvalds [Fri, 7 Nov 2014 19:54:44 +0000 (11:54 -0800)]
Merge tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
Johannes Berg [Thu, 30 Oct 2014 09:00:35 +0000 (10:00 +0100)]
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Aristeu Rozanski [Thu, 16 Oct 2014 15:49:49 +0000 (11:49 -0400)]
tiny: reverse logic for DISABLE_DEV_COREDUMP
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
projects / kernel.git / log