btrfs: rename setup_extent_mapping in relocation code
In btrfs code we have two functions called setup_extent_mapping, one in
the extent_map code and one in the relocation code. While both are
private to their respective implementation, this can still be confusing
for the reader.
So rename the version in relocation.c to setup_relocation_extent_mapping.
No functional changes.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: zoned: allow preallocation for relocation inodes
Now that we use a dedicated block group and regular writes for data
relocation, we can preallocate the space needed for a relocated inode,
just like we do in regular mode.
Essentially this reverts commit 32430c614844 ("btrfs: zoned: enable
relocation on a zoned filesystem") as it is not needed anymore.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: zoned: only allow one process to add pages to a relocation inode
Don't allow more than one process to add pages to a relocation inode on
a zoned filesystem, otherwise we cannot guarantee the sequential write
rule once we're filling preallocated extents on a zoned filesystem.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: zoned: add a dedicated data relocation block group
Relocation in a zoned filesystem can fail with a transaction abort with
error -22 (EINVAL). This happens because the relocation code assumes that
the extents we relocated the data to have the same size the source extents
had and ensures this by preallocating the extents.
But in a zoned filesystem we currently can't preallocate the extents as
this would break the sequential write required rule. Therefore it can
happen that the writeback process kicks in while we're still adding pages
to a delalloc range and starts writing out dirty pages.
This then creates destination extents that are smaller than the source
extents, triggering the following safety check in get_new_location():
1034 if (num_bytes != btrfs_file_extent_disk_num_bytes(leaf, fi)) {
1035 ret = -EINVAL;
1036 goto out;
1037 }
Temporarily create a dedicated block group for the relocation process, so
no non-relocation data writes can interfere with the relocation writes.
This is needed that we can switch the relocation process on a zoned
filesystem from the REQ_OP_ZONE_APPEND writing we use for data to a scheme
like in a non-zoned filesystem using REQ_OP_WRITE and preallocation.
Fixes: 32430c614844 ("btrfs: zoned: enable relocation on a zoned filesystem") Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Function repair_io_failure() is no longer used out of extent_io.c since
commit 8b9b6f255485 ("btrfs: scrub: cleanup the remaining nodatasum
fixup code"), which removes the last external caller.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:40 +0000 (15:30 +0100)]
btrfs: do not commit delayed inode when logging a file in full sync mode
When logging a regular file in full sync mode, we are currently committing
its delayed inode item. This is to ensure that we never miss copying the
inode item, with its most up to date data, into the log tree.
However that is not necessary since commit e4545de5b035 ("Btrfs: fix fsync
data loss after append write"), because even if we don't find the leaf
with the inode item when looking for leaves that changed in the current
transaction, we end up logging the inode item later using the in-memory
content. In case we find the leaf containing the inode item, we already
end up using the in-memory inode for filling the inode item in the log
tree, and not the inode item that is in the fs/subvolume tree, as it
might be not up to date (copy_items() -> fill_inode_item()).
So don't commit the delayed inode item, which brings a couple of benefits:
1) Avoid writing the inode item to the fs/subvolume btree, saving time and
reducing lock contention on the btree;
2) In case no other item for the inode was changed, added or deleted in
the same leaf where the inode item is located, we ended up copying
all the items in that leaf to the log tree - it's harmless from a
functional point of view, but it wastes time and log tree space.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 10/10 and the following test results compare a branch with
the whole patch set applied versus a branch without any of the patches
applied.
The following script was used to test dbench with 8 and 16 jobs on a
machine with 12 cores, 64G of RAM, a NVME device and using a non-debug
kernel config (Debian's default):
$ cat test.sh
#!/bin/bash
if [ $# -ne 1 ]; then
echo "Use $0 NUM_JOBS"
exit 1
fi
NUM_JOBS=$1
DEV=/dev/nvme0n1
MNT=/mnt/nvme0n1
MOUNT_OPTIONS="-o ssd"
MKFS_OPTIONS="-m single -d single"
echo "performance" | \
tee /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
mkfs.btrfs -f $MKFS_OPTIONS $DEV
mount $MOUNT_OPTIONS $DEV $MNT
Filipe Manana [Tue, 31 Aug 2021 14:30:39 +0000 (15:30 +0100)]
btrfs: avoid attempt to drop extents when logging inode for the first time
When logging an extent, in the fast fsync path, we always attempt do drop
or trim any existing extents with a range that match or overlap the range
of the extent we are about to log. We do that through a call to
btrfs_drop_extents().
However this is not needed when we are logging the inode for the first
time in the current transaction, since we have no inode items of the
inode in the log tree. Calling btrfs_drop_extents() does a deletion search
on the log tree, which is expensive when we have concurrent tasks
accessing the log tree because a deletion search always acquires a write
lock on the extent buffers at levels 2, 1 and 0, adding significant lock
contention, specially taking into account the height of a log tree rarely
(if ever) goes beyond 2 or 3, due to its short life.
So skip the call to btrfs_drop_extents() when the inode was not previously
logged in the current transaction.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 9/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:38 +0000 (15:30 +0100)]
btrfs: avoid search for logged i_size when logging inode if possible
If we are logging that an inode exists and the inode was not logged
before, we can avoid searching in the log tree for the inode item since we
know it does not exists. That wastes time and adds more lock contention on
the extent buffers of the log tree when there are other tasks that are
logging other inodes.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 8/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:37 +0000 (15:30 +0100)]
btrfs: avoid expensive search when truncating inode items from the log
Whenever we are logging a file inode in full sync mode we call
btrfs_truncate_inode_items() to delete items of the inode we may have
previously logged.
That results in doing a btree search for deletion, which is expensive
because it always acquires write locks for extent buffers at levels 2, 1
and 0, and it balances any node that is less than half full. Acquiring
the write locks can block the task if the extent buffers are already
locked by another task or block other tasks attempting to lock them,
which is specially bad in case of log trees since they are small due to
their short life, with a root node at a level typically not greater than
level 2.
If we know that we are logging the inode for the first time in the current
transaction, we can skip the call to btrfs_truncate_inode_items(), avoiding
the deletion search. This change does that.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 7/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:36 +0000 (15:30 +0100)]
btrfs: add helper to truncate inode items when logging inode
Move the call to btrfs_truncate_inode_items(), and the surrounding retry
loop, into a local helper function. This avoids some repetition and avoids
making the next change a bit awkward due to a bit of too much indentation.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 6/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:35 +0000 (15:30 +0100)]
btrfs: avoid expensive search when dropping inode items from log
Whenever we are logging a directory inode, logging that an inode exists or
logging an inode that has changes in its references or xattrs, we attempt
to delete items of this inode we may have previously logged (through calls
to drop_objectid_items()).
That attempt does a btree search for deletion, which is expensive because
it always acquires write locks for extent buffers at levels 2, 1 and 0,
and it balances any node that is less than half full. Acquiring the write
locks can block the task if the extent buffers are already locked or block
other tasks attempting to lock them, which is specially bad in case of log
trees since they are small due to their short life, with a root node at a
level typically not greater than level 2.
If we know that we are logging the inode for the first time in the current
transaction, we can skip the search. This change does that.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 5/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:34 +0000 (15:30 +0100)]
btrfs: always update the logged transaction when logging new names
When we are logging a new name for an inode, due to a link or rename
operation, if the inode has ancestor inodes that are new, created in the
current transaction, we need to log that these inodes exist. To ensure
that a subsequent explicit fsync on one of these ancestor inodes does
sync the log, we don't set the logged_trans field of these inodes.
This was done in commit 75b463d2b47aef ("btrfs: do not commit logs and
transactions during link and rename operations"), to avoid syncing a
log after a rename or link operation.
In order to allow for future changes to do some optimizations, change
this behaviour to always update the logged_trans of any logged inode
and don't update the last_log_commit of the inode if we are logging
that it exists. This accomplishes that same objective with simpler
logic, allowing for some optimizations in the next patches.
So just do that simplification.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 4/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:33 +0000 (15:30 +0100)]
btrfs: do not log new dentries when logging that a new name exists
When logging a new name for an inode, due to a link or rename operation,
we don't need to log all new dentries of the parent directories and their
subdirectories. We only want to log the names of the inode and that any
new parent directories exist. So in this case don't trigger logging of
the new dentries, that is only need when doing an explicit fsync on a
directory or on a file which requires logging its parent directories.
This avoids unnecessary work and reduces contention on the extent buffers
of a log tree.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 3/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:32 +0000 (15:30 +0100)]
btrfs: remove no longer needed checks for NULL log context
Since commit 75b463d2b47aef ("btrfs: do not commit logs and transactions
during link and rename operations"), we always pass a non-NULL log context
to btrfs_log_inode_parent() and therefore to all the functions that it
calls. So remove the checks we have all over the place that test for a
NULL log context, making the code shorter and easier to read, as well as
reducing the size of the generated code.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 2/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Filipe Manana [Tue, 31 Aug 2021 14:30:31 +0000 (15:30 +0100)]
btrfs: check if a log tree exists at inode_logged()
In case an inode was never logged since it was loaded from disk and was
modified in the current transaction (its ->last_trans matches the ID of
the current transaction), inode_logged() returns true even if there's no
existing log tree. In this case we can simply check if a log tree exists
and return false if it does not. This avoids a caller of inode_logged()
doing some unnecessary, but harmless, work.
For btrfs_log_new_name() it avoids it logging an inode in case it was
never logged since it was loaded from disk and there is currently no log
tree for the inode's root. For the remaining callers of inode_logged(),
btrfs_del_dir_entries_in_log() and btrfs_del_inode_ref_in_log(), it has
no effect since they already check if a log tree exists through their
calls to join_running_log_trans().
So just add a check to inode_logged() to verify if a log tree exists, and
return false if it does not.
This patch is part of a patch set comprised of the following patches:
btrfs: check if a log tree exists at inode_logged()
btrfs: remove no longer needed checks for NULL log context
btrfs: do not log new dentries when logging that a new name exists
btrfs: always update the logged transaction when logging new names
btrfs: avoid expensive search when dropping inode items from log
btrfs: add helper to truncate inode items when logging inode
btrfs: avoid expensive search when truncating inode items from the log
btrfs: avoid search for logged i_size when logging inode if possible
btrfs: avoid attempt to drop extents when logging inode for the first time
btrfs: do not commit delayed inode when logging a file in full sync mode
This is patch 1/10 and test results are listed in the change log of the
last patch in the set.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Tue, 24 Aug 2021 05:05:22 +0000 (13:05 +0800)]
btrfs: remove stale comment about the btrfs_show_devname
There were few lockdep warnings because btrfs_show_devname() was using
device_list_mutex as recorded in the commits:
0ccd05285e7f ("btrfs: fix a possible umount deadlock") 779bf3fefa83 ("btrfs: fix lock dep warning, move scratch dev out of device_list_mutex and uuid_mutex")
And finally, commit 88c14590cdd6 ("btrfs: use RCU in btrfs_show_devname
for device list traversal") removed the device_list_mutex from
btrfs_show_devname for performance reasons.
This patch removes a stale comment about the function
btrfs_show_devname and device_list_mutex.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Tue, 24 Aug 2021 05:05:21 +0000 (13:05 +0800)]
btrfs: update latest_dev when we create a sprout device
When we add a device to the seed filesystem (sprouting) it is a new
filesystem (and fsid) on the device added. Update the latest_dev so
that /proc/self/mounts shows the correct device.
Reason:
While btrfs_prepare_sprout() moves the fs_devices::devices into
fs_devices::seed_list, the btrfs_show_devname() searches for the devices
and found none, leading to the warning as in above.
Fix:
latest_dev is updated according to the changes to the device list.
That means we could use the latest_dev->name to show the device name in
/proc/self/mounts, the pointer will be always valid as it's assigned
before the device is deleted from the list in remove or replace.
The RCU protection is sufficient as the device structure is freed after
synchronization.
Reported-by: Su Yue <l@damenly.su> Tested-by: Su Yue <l@damenly.su> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Tue, 24 Aug 2021 05:05:19 +0000 (13:05 +0800)]
btrfs: convert latest_bdev type to btrfs_device and rename
In preparation to fix a bug in btrfs_show_devname().
Convert fs_devices::latest_bdev type from struct block_device to struct
btrfs_device and, rename the member to fs_devices::latest_dev.
So that btrfs_show_devname() can use fs_devices::latest_dev::name.
Tested-by: Su Yue <l@damenly.su> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:23 +0000 (21:19 +0900)]
btrfs: zoned: finish fully written block group
If we have written to the zone capacity, the device automatically
deactivates the zone. Sync up block group side (the active BG list and
zone_is_active flag) with it.
We need to do it both on data BGs and metadata BGs. On data side, we add a
hook to btrfs_finish_ordered_io(). On metadata side, we use
end_extent_buffer_writeback().
To reduce excess lookup of a block group, we mark the last extent buffer in
a block group with EXTENT_BUFFER_ZONE_FINISH flag. This cannot be done for
data (ordered_extent), because the address may change due to
REQ_OP_ZONE_APPEND.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:22 +0000 (21:19 +0900)]
btrfs: zoned: avoid chunk allocation if active block group has enough space
The current extent allocator tries to allocate a new block group when the
existing block groups do not have enough space. On a ZNS device, a new
block group means a new active zone. If the number of active zones has
already reached the max_active_zones, activating a new zone needs to finish
an existing zone, leading to wasting the free space there.
So, instead, it should reuse the existing active block groups as much as
possible when we can't activate any other zones without sacrificing an
already activated block group.
While at it, I converted find_free_extent_update_loop() to check the
found_extent() case early and made the other conditions simpler.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:21 +0000 (21:19 +0900)]
btrfs: move ffe_ctl one level up
We are passing too many variables as it is from btrfs_reserve_extent() to
find_free_extent(). The next commit will add min_alloc_size to ffe_ctl, and
that means another pass-through argument. Take this opportunity to move
ffe_ctl one level up and drop the redundant arguments.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:20 +0000 (21:19 +0900)]
btrfs: zoned: activate new block group
Activate new block group at btrfs_make_block_group(). We do not check the
return value. If failed, we can try again later at the actual extent
allocation phase.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:19 +0000 (21:19 +0900)]
btrfs: zoned: activate block group on allocation
Activate a block group when trying to allocate an extent from it. We check
read-only case and no space left case before trying to activate a block
group not to consume the number of active zones uselessly.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:17 +0000 (21:19 +0900)]
btrfs: zoned: implement active zone tracking
Add zone_is_active flag to btrfs_block_group. This flag indicates the
underlying zones are all active. Such zone active block groups are tracked
by fs_info->active_bg_list.
btrfs_dev_{set,clear}_active_zone() take responsibility for the underlying
device part. They set/clear the bitmap to indicate zone activeness and
count the number of zones we can activate left.
btrfs_zone_{activate,finish}() take responsibility for the logical part and
the list management. In addition, btrfs_zone_finish() wait for any writes
on it and send REQ_OP_ZONE_FINISH to the zone.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:16 +0000 (21:19 +0900)]
btrfs: zoned: introduce physical_map to btrfs_block_group
We will use a block group's physical location to track active zones and
finish fully written zones in the following commits. Since the zone
activation is done in the extent allocation context which already holding
the tree locks, we can't query the chunk tree for the physical locations.
So, copy the location info into a block group and use it for activation.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:15 +0000 (21:19 +0900)]
btrfs: zoned: load active zone information from devices
The ZNS specification defines a limit on the number of zones that can be in
the implicit open, explicit open or closed conditions. Any zone with such
condition is defined as an active zone and correspond to any zone that is
being written or that has been only partially written. If the maximum
number of active zones is reached, we must either reset or finish some
active zones before being able to chose other zones for storing data.
Load queue_max_active_zones() and track the number of active zones left on
the device.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:14 +0000 (21:19 +0900)]
btrfs: zoned: finish superblock zone once no space left for new SB
If there is no more space left for a new superblock in a superblock zone,
then it is better to ZONE_FINISH the zone and frees up the active zone
count.
Since btrfs_advance_sb_log() can now issue REQ_OP_ZONE_FINISH, we also need
to convert it to return int for the error case.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:13 +0000 (21:19 +0900)]
btrfs: zoned: locate superblock position using zone capacity
sb_write_pointer() returns the write position of next superblock. For READ,
we need a previous location. When the pointer is at the head, the previous
one is the last one of the other zone. Calculate the last one's position
from zone capacity.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:11 +0000 (21:19 +0900)]
btrfs: zoned: tweak reclaim threshold for zone capacity
With the introduction of zone capacity, the range [capacity, length] is
always zone unusable. Counting this region as a reclaim target will
cause reclaiming too early. Reclaim block groups based on bytes that can
be usable after resetting.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:10 +0000 (21:19 +0900)]
btrfs: zoned: calculate free space from zone capacity
Now that we introduced capacity in a block group, we need to calculate free
space using the capacity instead of the length. Thus, bytes we account
capacity - alloc_pointer as free, and account bytes [capacity, length] as
zone unusable.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:09 +0000 (21:19 +0900)]
btrfs: zoned: move btrfs_free_excluded_extents out of btrfs_calc_zone_unusable
btrfs_free_excluded_extents() is not neccessary for
btrfs_calc_zone_unusable() and it makes btrfs_calc_zone_unusable()
difficult to reuse. Move it out and call btrfs_free_excluded_extents()
in proper context.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Naohiro Aota [Thu, 19 Aug 2021 12:19:08 +0000 (21:19 +0900)]
btrfs: zoned: load zone capacity information from devices
The ZNS specification introduces the concept of a Zone Capacity. A zone
capacity is an additional per-zone attribute that indicates the number of
usable logical blocks within each zone, starting from the first logical
block of each zone. It is always smaller or equal to the zone size.
With the SINGLE profile, we can set a block group's "capacity" as the same
as the underlying zone's Zone Capacity. We will limit the allocation not
to exceed in a following commit.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 6 Aug 2021 08:12:39 +0000 (16:12 +0800)]
btrfs: defrag: introduce helper to defrag one cluster
This new helper, defrag_one_cluster(), will defrag one cluster (at most
256K):
- Collect all initial targets
- Kick in readahead when possible
- Call defrag_one_range() on each initial target
With some extra range clamping.
- Update @sectors_defragged parameter
This involves one behavior change, the defragged sectors accounting is
no longer as accurate as old behavior, as the initial targets are not
consistent.
We can have new holes punched inside the initial target, and we will
skip such holes later.
But the defragged sectors accounting doesn't need to be that accurate
anyway, thus I don't want to pass those extra accounting burden into
defrag_one_range().
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 6 Aug 2021 08:12:38 +0000 (16:12 +0800)]
btrfs: defrag: introduce helper to defrag a range
A new helper, defrag_one_range(), is introduced to defrag one range.
This function will mostly prepare the needed pages and extent status for
defrag_one_locked_target().
As we can only have a consistent view of extent map with page and extent
bits locked, we need to re-check the range passed in to get a real
target list for defrag_one_locked_target().
Since defrag_collect_targets() will call defrag_lookup_extent() and lock
extent range, we also need to teach those two functions to skip extent
lock. Thus new parameter, @locked, is introduced to skip extent lock if
the caller has already locked the range.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 6 Aug 2021 08:12:34 +0000 (16:12 +0800)]
btrfs: defrag: replace hard coded PAGE_SIZE with sectorsize
When testing subpage defrag support, I always find some strange inode
nbytes error, after a lot of debugging, it turns out that
defrag_lookup_extent() is using PAGE_SIZE as size for
lookup_extent_mapping().
Since lookup_extent_mapping() is calling __lookup_extent_mapping() with
@strict == 1, this means any extent map smaller than one page will be
ignored, prevent subpage defrag to grab a correct extent map.
There are quite some PAGE_SIZE usage in ioctl.c, but most of them are
correct usages, and can be one of the following cases:
- ioctl structure size check
We want ioctl structure to be contained inside one page.
- real page operations
The remaining cases in defrag_lookup_extent() and
check_defrag_in_cache() will be addressed in this patch.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Fri, 6 Aug 2021 08:12:32 +0000 (16:12 +0800)]
btrfs: defrag: pass file_ra_state instead of file to btrfs_defrag_file()
Currently btrfs_defrag_file() accepts both "struct inode" and "struct
file" as parameter. We can easily grab "struct inode" from "struct
file" using file_inode() helper.
The reason why we need "struct file" is just to re-use its f_ra.
Change this to pass "struct file_ra_state" parameter, so that it's more
clear what we really want. Since we're here, also add some comments on
the function btrfs_defrag_file().
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Anand Jain [Tue, 24 Aug 2021 05:27:42 +0000 (13:27 +0800)]
btrfs: rename and switch to bool btrfs_chunk_readonly
btrfs_chunk_readonly() checks if the given chunk is writeable. It
returns 1 for readonly, and 0 for writeable. So the return argument type
bool shall suffice instead of the current type int.
Also, rename btrfs_chunk_readonly() to btrfs_chunk_writeable() as we
check if the bg is writeable, and helps to keep the logic at the parent
function simpler to understand.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Sidong Yang [Thu, 26 Aug 2021 14:44:36 +0000 (14:44 +0000)]
btrfs: reflink: initialize return value to 0 in btrfs_extent_same()
Fix a warning reported by smatch that ret could be returned without
initialized. The dedupe operations are supposed to to return 0 for a 0
length range but the caller does not pass olen == 0. To keep this
behaviour and also fix the warning initialize ret to 0.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Sidong Yang <realwakka@gmail.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 17 Aug 2021 09:38:52 +0000 (17:38 +0800)]
btrfs: subpage: pack all subpage bitmaps into a larger bitmap
Currently we use u16 bitmap to make 4k sectorsize work for 64K page
size.
But this u16 bitmap is not large enough to contain larger page size like
128K, nor is space efficient for 16K page size.
To handle both cases, here we pack all subpage bitmaps into a larger
bitmap, now btrfs_subpage::bitmaps[] will be the ultimate bitmap for
subpage usage.
Each sub-bitmap will has its start bit number recorded in
btrfs_subpage_info::*_start, and its bitmap length will be recorded in
btrfs_subpage_info::bitmap_nr_bits.
All subpage bitmap operations will be converted from using direct u16
operations to bitmap operations, with above *_start calculated.
For 64K page size with 4K sectorsize, this should not cause much
difference.
While for 16K page size, we will only need 1 unsigned long (u32) to
store all the bitmaps, which saves quite some space.
Furthermore, this allows us to support larger page size like 128K and
258K.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 17 Aug 2021 09:38:50 +0000 (17:38 +0800)]
btrfs: subpage: make btrfs_alloc_subpage() return btrfs_subpage directly
The existing calling convention of btrfs_alloc_subpage() is pretty
awful. Change it to a more common pattern by returning struct
btrfs_subpage directly and let the caller to determine if the call
succeeded.
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Qu Wenruo [Tue, 17 Aug 2021 09:38:49 +0000 (17:38 +0800)]
btrfs: subpage: only call btrfs_alloc_subpage() when sectorsize is smaller than PAGE_SIZE
There are two call sites of btrfs_alloc_subpage():
- btrfs_attach_subpage()
We have ensured sectorsize is smaller than PAGE_SIZE
- alloc_extent_buffer()
We call btrfs_alloc_subpage() unconditionally.
The alloc_extent_buffer() forces us to check the sectorsize size against
page size inside btrfs_alloc_subpage().
Since the function name, btrfs_alloc_subpage(), already indicates it
should only get called for subpage cases, do the check in
alloc_extent_buffer() and add an ASSERT() in btrfs_alloc_subpage().
Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
The out label is being overused, we can simply return if the condition
permits.
No functional changes.
Reviewed-by: Su Yue <l@damenly.su> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Nikolay Borisov [Wed, 18 Aug 2021 10:41:19 +0000 (13:41 +0300)]
btrfs: rename btrfs_alloc_chunk to btrfs_create_chunk
The user facing function used to allocate new chunks is
btrfs_chunk_alloc, unfortunately there is yet another similar sounding
function - btrfs_alloc_chunk. This creates confusion, especially since
the latter function can be considered "private" in the sense that it
implements the first stage of chunk creation and as such is called by
btrfs_chunk_alloc.
To avoid the awkwardness that comes with having similarly named but
distinctly different in their purpose function rename btrfs_alloc_chunk
to btrfs_create_chunk, given that the main purpose of this function is
to orchestrate the whole process of allocating a chunk - reserving space
into devices, deciding on characteristics of the stripe size and
creating the in-memory structures.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
secretmem: Prevent secretmem_users from wrapping to zero
Commit 110860541f44 ("mm/secretmem: use refcount_t instead of atomic_t")
attempted to fix the problem of secretmem_users wrapping to zero and
allowing suspend once again.
But it was reverted in commit 87066fdd2e30 ("Revert 'mm/secretmem: use
refcount_t instead of atomic_t'") because of the problems it caused - a
refcount_t was not semantically the right type to use.
Instead prevent secretmem_users from wrapping to zero by forbidding new
users if the number of users has wrapped from positive to negative.
This stops a long way short of reaching the necessary 4 billion users
where it wraps to zero again, so there's no need to be clever with
special anti-wrap types or checking the return value from atomic_inc().
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Jordy Zomer <jordy@pwning.systems> Cc: Kees Cook <keescook@chromium.org>, Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 25 Oct 2021 17:46:41 +0000 (10:46 -0700)]
spi: Fix tegra20 build with CONFIG_PM=n once again
Commit efafec27c565 ("spi: Fix tegra20 build with CONFIG_PM=n") already
fixed the build without PM support once. There was an alternative fix
by Guenter in commit 2bab94090b01 ("spi: tegra20-slink: Declare runtime
suspend and resume functions conditionally"), and Mark then merged the
two correctly in ffb1e76f4f32 ("Merge tag 'v5.15-rc2' into spi-5.15").
But for some inexplicable reason, Mark then merged things _again_ in
commit 59c4e190b10c ("Merge tag 'v5.15-rc3' into spi-5.15"), and screwed
things up at that point, and the __maybe_unused attribute on
tegra_slink_runtime_resume() went missing.
Reinstate it, so that alpha (and other architectures without PM support)
builds cleanly again.
Btw, this is another prime example of how random back-merges are not
good. Just don't do them. Subsystem developers should not merge my
tree in any normal circumstances. Both of those merge commits pointed
to above are bad: even the one that got the merge result right doesn't
even mention _why_ it was done, and the one that got it wrong is
obviously broken.
Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 25 Oct 2021 16:47:18 +0000 (09:47 -0700)]
Merge tag 'pinctrl-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some late pin control fixes, the most generally annoying will probably
be the AMD IRQ storm fix affecting the Microsoft surface.
Summary:
- Three fixes pertaining to Broadcom DT bindings. Some stuff didn't
work out as inteded, we need to back out
- A resume bug fix in the STM32 driver
- Disable and mask the interrupts on probe in the AMD pinctrl driver,
affecting Microsoft surface"
* tag 'pinctrl-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: amd: disable and mask interrupts on probe
pinctrl: stm32: use valid pin identifier in stm32_pinctrl_resume()
Revert "pinctrl: bcm: ns: support updated DT binding as syscon subnode"
dt-bindings: pinctrl: brcm,ns-pinmux: drop unneeded CRU from example
Revert "dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon"
LABBE Corentin [Thu, 21 Oct 2021 09:26:57 +0000 (10:26 +0100)]
ARM: 9148/1: handle CONFIG_CPU_ENDIAN_BE32 in arch/arm/kernel/head.S
My intel-ixp42x-welltech-epbx100 no longer boot since 4.14.
This is due to commit 463dbba4d189 ("ARM: 9104/2: Fix Keystone 2 kernel
mapping regression")
which forgot to handle CONFIG_CPU_ENDIAN_BE32 as possible BE config.
Suggested-by: Krzysztof Hałasa <khalasa@piap.pl> Fixes: 463dbba4d189 ("ARM: 9104/2: Fix Keystone 2 kernel mapping regression") Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Converting the "secretmem_users" counter to a refcount is incorrect,
because a refcount is special in zero and can't just be incremented (but
a count of users is not, and "no users" is actually perfectly valid and
not a sign of a free'd resource).
Reported-by: syzbot+75639e6a0331cd61d3e2@syzkaller.appspotmail.com Cc: Jordy Zomer <jordy@pwning.systems> Cc: Kees Cook <keescook@chromium.org>, Cc: Jordy Zomer <jordy@jordyzomer.github.io> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* tag '5.15-rc6-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: add buffer validation in session setup
ksmbd: throttle session setup failures to avoid dictionary attacks
ksmbd: validate OutputBufferLength of QUERY_DIR, QUERY_INFO, IOCTL requests
ksmbd: validate credit charge after validating SMB2 PDU body size
ksmbd: add buffer validation for smb direct
ksmbd: limit read/write/trans buffer size not to exceed 8MB
ksmbd: validate compound response buffer
ksmbd: fix potencial 32bit overflow from data area check in smb2_write
ksmbd: improve credits management
ksmbd: add validation in smb2_ioctl
Linus Torvalds [Sun, 24 Oct 2021 16:23:48 +0000 (06:23 -1000)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Ten fixes, seven of which are in drivers.
The core fixes are one to fix a potential crash on resume, one to sort
out our reference count releases to avoid releasing in-use modules and
one to adjust the cmd per lun calculation to avoid an overflow in
hyper-v"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: ufs-pci: Force a full restore after suspend-to-disk
scsi: qla2xxx: Fix unmap of already freed sgl
scsi: qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()
scsi: qla2xxx: Return -ENOMEM if kzalloc() fails
scsi: sd: Fix crashes in sd_resume_runtime()
scsi: mpi3mr: Fix duplicate device entries when scanning through sysfs
scsi: core: Put LLD module refcnt after SCSI device is released
scsi: storvsc: Fix validation for unsolicited incoming packets
scsi: iscsi: Fix set_param() handling
scsi: core: Fix shost->cmd_per_lun calculation in scsi_add_host_with_dma()
Linus Torvalds [Sat, 23 Oct 2021 03:42:13 +0000 (17:42 -1000)]
Merge tag 'block-5.15-2021-10-22' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Fix for the cgroup code not ussing irq safe stats updates, and one fix
for an error handling condition in add_partition()"
* tag 'block-5.15-2021-10-22' of git://git.kernel.dk/linux-block:
block: fix incorrect references to disk objects
blk-cgroup: blk_cgroup_bio_start() should use irq-safe operations on blkg->iostat_cpu
Linus Torvalds [Sat, 23 Oct 2021 03:34:31 +0000 (17:34 -1000)]
Merge tag 'io_uring-5.15-2021-10-22' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two fixes for the max workers limit API that was introduced this
series: one fix for an issue with that code, and one fixing a linked
timeout regression in this series"
* tag 'io_uring-5.15-2021-10-22' of git://git.kernel.dk/linux-block:
io_uring: apply worker limits to previous users
io_uring: fix ltimeout unprep
io_uring: apply max_workers limit to all future users
io-wq: max_worker fixes
Linus Torvalds [Fri, 22 Oct 2021 20:39:47 +0000 (10:39 -1000)]
Merge tag 'fuse-fixes-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Syzbot discovered a race in case of reusing the fuse sb (introduced in
this cycle).
Fix it by doing the s_fs_info initialization at the proper place"
* tag 'fuse-fixes-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: clean up error exits in fuse_fill_super()
fuse: always initialize sb->s_fs_info
fuse: clean up fuse_mount destruction
fuse: get rid of fuse_put_super()
fuse: check s_root when destroying sb
Arnd Bergmann [Mon, 18 Oct 2021 13:19:08 +0000 (15:19 +0200)]
hyperv/vmbus: include linux/bitops.h
On arm64 randconfig builds, hyperv sometimes fails with this
error:
In file included from drivers/hv/hv_trace.c:3:
In file included from drivers/hv/hyperv_vmbus.h:16:
In file included from arch/arm64/include/asm/sync_bitops.h:5:
arch/arm64/include/asm/bitops.h:11:2: error: only <linux/bitops.h> can be included directly
In file included from include/asm-generic/bitops/hweight.h:5:
include/asm-generic/bitops/arch_hweight.h:9:9: error: implicit declaration of function '__sw_hweight32' [-Werror,-Wimplicit-function-declaration]
include/asm-generic/bitops/atomic.h:17:7: error: implicit declaration of function 'BIT_WORD' [-Werror,-Wimplicit-function-declaration]
Linus Torvalds [Fri, 22 Oct 2021 19:08:08 +0000 (09:08 -1000)]
Merge tag 'acpi-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two regressions, one related to ACPI power resources
management and one that broke ACPI tools compilation.
Specifics:
- Stop turning off unused ACPI power resources in an unknown state to
address a regression introduced during the 5.14 cycle (Rafael
Wysocki).
- Fix an ACPI tools build issue introduced recently when the minimal
stdarg.h was added (Miguel Bernal Marin)"
* tag 'acpi-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: Do not turn off power resources in unknown state
ACPI: tools: fix compilation error
Linus Torvalds [Fri, 22 Oct 2021 19:02:15 +0000 (09:02 -1000)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more x86 kvm fixes from Paolo Bonzini:
- Cache coherency fix for SEV live migration
- Fix for instruction emulation with PKU
- fixes for rare delaying of interrupt delivery
- fix for SEV-ES buffer overflow
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: go over the sev_pio_data buffer in multiple passes if needed
KVM: SEV-ES: keep INS functions together
KVM: x86: remove unnecessary arguments from complete_emulator_pio_in
KVM: x86: split the two parts of emulator_pio_in
KVM: SEV-ES: clean up kvm_sev_es_ins/outs
KVM: x86: leave vcpu->arch.pio.count alone in emulator_pio_in_out
KVM: SEV-ES: rename guest_ins_data to sev_pio_data
KVM: SEV: Flush cache on non-coherent systems before RECEIVE_UPDATE_DATA
KVM: MMU: Reset mmu->pkru_mask to avoid stale data
KVM: nVMX: promptly process interrupts delivered while in guest mode
KVM: x86: check for interrupts before deciding whether to exit the fast path
Paolo Bonzini [Tue, 12 Oct 2021 15:33:03 +0000 (11:33 -0400)]
KVM: SEV-ES: go over the sev_pio_data buffer in multiple passes if needed
The PIO scratch buffer is larger than a single page, and therefore
it is not possible to copy it in a single step to vcpu->arch/pio_data.
Bound each call to emulator_pio_in/out to a single page; keep
track of how many I/O operations are left in vcpu->arch.sev_pio_count,
so that the operation can be restarted in the complete_userspace_io
callback.
For OUT, this means that the previous kvm_sev_es_outs implementation
becomes an iterator of the loop, and we can consume the sev_pio_data
buffer before leaving to userspace.
For IN, instead, consuming the buffer and decreasing sev_pio_count
is always done in the complete_userspace_io callback, because that
is when the memcpy is done into sev_pio_data.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reported-by: Felix Wilhelm <fwilhelm@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 12 Oct 2021 16:35:20 +0000 (12:35 -0400)]
KVM: x86: remove unnecessary arguments from complete_emulator_pio_in
complete_emulator_pio_in can expect that vcpu->arch.pio has been filled in,
and therefore does not need the size and count arguments. This makes things
nicer when the function is called directly from a complete_userspace_io
callback.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Wed, 13 Oct 2021 16:32:02 +0000 (12:32 -0400)]
KVM: x86: split the two parts of emulator_pio_in
emulator_pio_in handles both the case where the data is pending in
vcpu->arch.pio.count, and the case where I/O has to be done via either
an in-kernel device or a userspace exit. For SEV-ES we would like
to split these, to identify clearly the moment at which the
sev_pio_data is consumed. To this end, create two different
functions: __emulator_pio_in fills in vcpu->arch.pio.count, while
complete_emulator_pio_in clears it and releases vcpu->arch.pio.data.
Because this patch has to be backported, things are left a bit messy.
kernel_pio() operates on vcpu->arch.pio, which leads to emulator_pio_in()
having with two calls to complete_emulator_pio_in(). It will be fixed
in the next release.
While at it, remove the unused void* val argument of emulator_pio_in_out.
The function currently hardcodes vcpu->arch.pio_data as the
source/destination buffer, which sucks but will be fixed after the more
severe SEV-ES buffer overflow.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 12 Oct 2021 14:51:55 +0000 (10:51 -0400)]
KVM: SEV-ES: clean up kvm_sev_es_ins/outs
A few very small cleanups to the functions, smushed together because
the patch is already very small like this:
- inline emulator_pio_in_emulated and emulator_pio_out_emulated,
since we already have the vCPU
- remove the data argument and pull setting vcpu->arch.sev_pio_data into
the caller
- remove unnecessary clearing of vcpu->arch.pio.count when
emulation is done by the kernel (and therefore vcpu->arch.pio.count
is already clear on exit from emulator_pio_in and emulator_pio_out).
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Wed, 13 Oct 2021 16:29:42 +0000 (12:29 -0400)]
KVM: x86: leave vcpu->arch.pio.count alone in emulator_pio_in_out
Currently emulator_pio_in clears vcpu->arch.pio.count twice if
emulator_pio_in_out performs kernel PIO. Move the clear into
emulator_pio_out where it is actually necessary.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 12 Oct 2021 14:22:34 +0000 (10:22 -0400)]
KVM: SEV-ES: rename guest_ins_data to sev_pio_data
We will be using this field for OUTS emulation as well, in case the
data that is pushed via OUTS spans more than one page. In that case,
there will be a need to save the data pointer across exits to userspace.
So, change the name to something that refers to any kind of PIO.
Also spell out what it is used for, namely SEV-ES.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Fri, 22 Oct 2021 05:06:08 +0000 (19:06 -1000)]
Merge tag 'drm-fixes-2021-10-22' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too crazy at the end of the cycle, the kmb modesetting fixes
are probably a bit large but it's not a major driver, and its fixing
monitor doesn't turn on type problems.
Otherwise it's just a few minor patches, one ast regression revert, an
msm power stability fix.
ast:
- fix regression with connector detect
msm:
- fix power stability issue
msxfb:
- fix crash on unload
panel:
- sync fix
kmb:
- modesetting fixes"
* tag 'drm-fixes-2021-10-22' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/ast: Add detect function support"
drm/kmb: Enable ADV bridge after modeset
drm/kmb: Corrected typo in handle_lcd_irq
drm/kmb: Disable change of plane parameters
drm/kmb: Remove clearing DPHY regs
drm/kmb: Limit supported mode to 1080p
drm/kmb: Work around for higher system clock
drm/panel: ilitek-ili9881c: Fix sync for Feixin K101-IM2BYL02 panel
drm: mxsfb: Fix NULL pointer dereference crash on unload
drm/msm/devfreq: Restrict idle clamping to a618 for now
Mike Rapoport [Thu, 21 Oct 2021 07:09:29 +0000 (10:09 +0300)]
memblock: exclude MEMBLOCK_NOMAP regions from kmemleak
Vladimir Zapolskiy reports:
Commit a7259df76702 ("memblock: make memblock_find_in_range method
private") invokes a kernel panic while running kmemleak on OF platforms
with nomaped regions:
Unable to handle kernel paging request at virtual address fff000021e00000
[...]
scan_block+0x64/0x170
scan_gray_list+0xe8/0x17c
kmemleak_scan+0x270/0x514
kmemleak_write+0x34c/0x4ac
The memory allocated from memblock is registered with kmemleak, but if
it is marked MEMBLOCK_NOMAP it won't have linear map entries so an
attempt to scan such areas will fault.
Ideally, memblock_mark_nomap() would inform kmemleak to ignore
MEMBLOCK_NOMAP memory, but it can be called before kmemleak interfaces
operating on physical addresses can use __va() conversion.
Make sure that functions that mark allocated memory as MEMBLOCK_NOMAP
take care of informing kmemleak to ignore such memory.
The crash happens because kmemleak_free_part_phys() tries to use __va()
before memstart_addr is initialized and this triggers a VM_BUG_ON() in
arch/arm64/include/asm/memory.h:
Revert 6e44bd6d34d6 ("memblock: exclude NOMAP regions from kmemleak"),
the issue it is fixing will be fixed differently.
Reported-by: Qian Cai <quic_qiancai@quicinc.com> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 22 Oct 2021 03:27:17 +0000 (17:27 -1000)]
Merge branch 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ucounts fixes from Eric Biederman:
"There has been one very hard to track down bug in the ucount code that
we have been tracking since roughly v5.14 was released. Alex managed
to find a reliable reproducer a few days ago and then I was able to
instrument the code and figure out what the issue was.
It turns out the sigqueue_alloc single atomic operation optimization
did not play nicely with ucounts multiple level rlimits. It turned out
that either sigqueue_alloc or sigqueue_free could be operating on
multiple levels and trigger the conditions for the optimization on
more than one level at the same time.
To deal with that situation I have introduced inc_rlimit_get_ucounts
and dec_rlimit_put_ucounts that just focuses on the optimization and
the rlimit and ucount changes.
While looking into the big bug I found I couple of other little issues
so I am including those fixes here as well.
When I have time I would very much like to dig into process ownership
of the shared signal queue and see if we could pick a single owner for
the entire queue so that all of the rlimits can count to that owner.
That should entirely remove the need to call get_ucounts and
put_ucounts in sigqueue_alloc and sigqueue_free. It is difficult
because Linux unlike POSIX supports setuid that works on a single
thread"
* 'ucount-fixes-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Move get_ucounts from cred_alloc_blank to key_change_session_keyring
ucounts: Proper error handling in set_cred_ucounts
ucounts: Pair inc_rlimit_ucounts with dec_rlimit_ucoutns in commit_creds
ucounts: Fix signal ucount refcounting
Linus Torvalds [Fri, 22 Oct 2021 01:36:50 +0000 (15:36 -1000)]
Merge tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, and can.
We'll have one more fix for a socket accounting regression, it's still
getting polished. Otherwise things look fine.
Current release - regressions:
- revert "vrf: reset skb conntrack connection on VRF rcv", there are
valid uses for previous behavior
- can: m_can: fix iomap_read_fifo() and iomap_write_fifo()
Current release - new code bugs:
- mlx5: e-switch, return correct error code on group creation failure
Previous releases - regressions:
- sctp: fix transport encap_port update in sctp_vtag_verify
- stmmac: fix E2E delay mechanism (in PTP timestamping)
Previous releases - always broken:
- netfilter: ip6t_rt: fix out-of-bounds read of ipv6_rt_hdr
- netfilter: xt_IDLETIMER: fix out-of-bound read caused by lack of
init
- netfilter: ipvs: make global sysctl read-only in non-init netns
- tcp: md5: fix selection between vrf and non-vrf keys
- ipv6: count rx stats on the orig netdev when forwarding
- bridge: mcast: use multicast_membership_interval for IGMPv3
- can:
- j1939: fix UAF for rx_kref of j1939_priv abort sessions on
receiving bad messages
- isotp: fix TX buffer concurrent access in isotp_sendmsg() fix
return error on FC timeout on TX path
- ice: fix re-init of RDMA Tx queues and crash if RDMA was not inited
- hns3: schedule the polling again when allocation fails, prevent
stalls
- drivers: add missing of_node_put() when aborting
for_each_available_child_of_node()
- ptp: fix possible memory leak and UAF in ptp_clock_register()
- e1000e: fix packet loss in burst mode on Tiger Lake and later
- mlx5e: ipsec: fix more checksum offload issues"
* tag 'net-5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (75 commits)
usbnet: sanity check for maxpacket
net: enetc: make sure all traffic classes can send large frames
net: enetc: fix ethtool counter name for PM0_TERR
ptp: free 'vclock_index' in ptp_clock_release()
sfc: Don't use netif_info before net_device setup
sfc: Export fibre-specific supported link modes
net/mlx5e: IPsec: Fix work queue entry ethernet segment checksum flags
net/mlx5e: IPsec: Fix a misuse of the software parser's fields
net/mlx5e: Fix vlan data lost during suspend flow
net/mlx5: E-switch, Return correct error code on group creation failure
net/mlx5: Lag, change multipath and bonding to be mutually exclusive
ice: Add missing E810 device ids
igc: Update I226_K device ID
e1000e: Fix packet loss on Tiger Lake and later
e1000e: Separate TGP board type from SPT
ptp: Fix possible memory leak in ptp_clock_register()
net: stmmac: Fix E2E delay mechanism
nfc: st95hf: Make spi remove() callback return zero
net: hns3: disable sriov before unload hclge layer
net: hns3: fix vf reset workqueue cannot exit
...
Linus Torvalds [Fri, 22 Oct 2021 01:30:09 +0000 (15:30 -1000)]
Merge tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a bug exposed by a previous fix, where running guests with
certain SMT topologies could crash the host on Power8.
- Fix atomic sleep warnings when re-onlining CPUs, when PREEMPT is
enabled.
Thanks to Nathan Lynch, Srikar Dronamraju, and Valentin Schneider.
* tag 'powerpc-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/smp: do not decrement idle task preempt count in CPU offline
powerpc/idle: Don't corrupt back chain when going idle
Pavel Begunkov [Thu, 21 Oct 2021 12:20:29 +0000 (13:20 +0100)]
io_uring: apply worker limits to previous users
Another change to the API io-wq worker limitation API added in 5.15,
apply the limit to all prior users that already registered a tctx. It
may be confusing as it's now, in particular the change covers the
following 2 cases:
A note on locking, it's safe to traverse ->tctx_list as we hold
->uring_lock, but do that after dropping sqd->lock to avoid possible
problems. It's also safe to access tctx->io_wq there because tasks
kill it only after removing themselves from tctx_list, see
io_uring_cancel_generic() -> io_uring_clean_tctx()
KVM: SEV: Flush cache on non-coherent systems before RECEIVE_UPDATE_DATA
Flush the destination page before invoking RECEIVE_UPDATE_DATA, as the
PSP encrypts the data with the guest's key when writing to guest memory.
If the target memory was not previously encrypted, the cache may contain
dirty, unecrypted data that will persist on non-coherent systems.
Fixes: 15fb7de1a7f5 ("KVM: SVM: Add KVM_SEV_RECEIVE_UPDATE_DATA command") Cc: stable@vger.kernel.org Cc: Peter Gonda <pgonda@google.com> Cc: Marc Orr <marcorr@google.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Masahiro Kozuka <masa.koz@kozuka.jp>
[sean: converted bug report to changelog] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210914210951.2994260-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
projects / kernel.git / log