drm/i915/psr: Make PSR registers relative to transcoders
PSR registers are a mess, some have the full address while others just
have the additional offset from psr_mmio_base.
For BDW+ psr_mmio_base is nothing more than TRANSCODER_EDP_OFFSET +
0x800 and using it makes more difficult for people with an PSR
register address or PSR register name from from BSpec as i915 also
don't match the BSpec names.
For HSW psr_mmio_base is _DDI_BUF_CTL_A + 0x800 and PSR registers are
only available in DDIA.
Other reason to make relative to transcoder is that since BDW every
transcoder have PSR registers, so in theory it should be possible to
have PSR enabled in a non-eDP transcoder.
So for BDW+ we can use _TRANS2() to get the register offset of any
PSR register in any transcoder while for HSW we have _HSW_PSR_ADJ
that will calculate the register offset for the single PSR instance,
noting that we are already guarded about trying to enable PSR in other
port than DDIA on HSW by the 'if (dig_port->base.port != PORT_A)' in
intel_psr_compute_config(), this check should only be valid for HSW
and will be changed in future.
PSR2 registers and PSR_EVENT was added after Haswell so that is why
_PSR_ADJ() is not used in some macros.
The only registers that can not be relative to transcoder are
PSR_IMR and PSR_IIR that are not relative to anything, so keeping it
hardcoded. That changed for TGL but it will be handled in another
patch.
Also removing BDW_EDP_PSR_BASE from GVT because it is not used as it
is the only PSR register that GVT have.
v5:
- Macros changed to be more explicit about HSW (Dhinakaran)
- Squashed with the patch that added the tran parameter to the
macros (Dhinakaran)
v6:
- Checking for interruption errors after module reload in the
transcoder that will be used (Dhinakaran)
- Using lowercase to the registers offsets
v7:
- Removing IS_HASWELL() from registers macros(Jani)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Zhi Wang <zhi.a.wang@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190820223325.27490-1-jose.souza@intel.com
Chris Wilson [Thu, 22 Aug 2019 06:59:17 +0000 (07:59 +0100)]
drm/i915: Kill the undead i915_gem_batch_pool.c
You have to cut it off at the neck, otherwise it just reappears in the
next merge, like it did in commit 3f866026f0ce ("Merge drm/drm-next
into drm-intel-next-queued")
Chris Wilson [Thu, 22 Aug 2019 06:15:57 +0000 (07:15 +0100)]
drm/i915: Replace i915_vma_put_fence()
Avoid calling i915_vma_put_fence() by using our alternate paths that
bind a secondary vma avoiding the original fenced vma. For the few
instances where we need to release the fence (i.e. on binding when the
GGTT range becomes invalid), replace the put_fence with a revoke_fence.
Chris Wilson [Thu, 22 Aug 2019 06:09:13 +0000 (07:09 +0100)]
drm/i915: Pull obj->userfault tracking under the ggtt->mutex
Since we want to revoke the ggtt vma from only under the ggtt->mutex, we
need to move protection of the userfault tracking from the struct_mutex
to the ggtt->mutex.
Chris Wilson [Thu, 22 Aug 2019 06:09:12 +0000 (07:09 +0100)]
drm/i915: Track ggtt fence reservations under its own mutex
We can reduce the locking for fence registers from the dev->struct_mutex
to a local mutex. We could introduce a mutex for the sole purpose of
tracking the fence acquisition, except there is a little bit of overlap
with the fault tracking, so use the i915_ggtt.mutex as it covers both.
Rodrigo Vivi [Thu, 22 Aug 2019 05:47:35 +0000 (22:47 -0700)]
Merge drm/drm-next into drm-intel-next-queued
We need the rename of reservation_object to dma_resv.
The solution on this merge came from linux-next:
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Wed, 14 Aug 2019 12:48:39 +1000
Subject: [PATCH] drm: fix up fallout from "dma-buf: rename reservation_object to dma_resv"
- if (reservation_object_trylock(resv)) {
- reservation_object_add_excl_fence(resv, NULL);
- reservation_object_unlock(resv);
+ if (dma_resv_trylock(resv)) {
+ dma_resv_add_excl_fence(resv, NULL);
+ dma_resv_unlock(resv);
}
err = i915_gem_object_pin_pages(node->obj);
which is a simplified version from a previous one which had: Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Dave Airlie [Thu, 22 Aug 2019 03:21:16 +0000 (13:21 +1000)]
Merge branch 'etnaviv/next' of https://git.pengutronix.de/git/lst/linux into drm-next
Most importantly per-process address spaces on GPUs that are capable of
providing proper isolation has finished baking. This is the base for
our softpin implementation, which allows us to support the texture
descriptor buffers used by GC7000 series GPUs without a major UAPI
extension/rework.
Shortlog of notable changes:
- code cleanup from Fabio
- fix performance counters on GC880 and GC2000 GPUs from Christian
- drmP.h header removal from Sam
- per process address space support on MMUv2 GPUs from me
- softpin support from me
Chris Wilson [Wed, 21 Aug 2019 19:38:51 +0000 (20:38 +0100)]
drm/i915/selftests: Fixup a couple of missing serialisation with vma
In commit 70d6894d1456 ("drm/i915: Serialize against vma moves")
I managed to miss a couple of i915_vma_move_to_active() that had not
serialised against an async vma pinning. Add the missing
i915_request_await.
Four drm_mm_node are used to reserve guest ggtt space, but some of them
may be skipped and not initialised due to space constraints in
intel_vgt_balloon(). If drm_mm_remove_node() is called with
uninitialized drm_mm_node, the above call trace occurs.
This patch check drm_mm_node's validity before calling
drm_mm_remove_node().
Fixes: ff8f797557c7("drm/i915: return the correct usable aperture size under gvt environment") Cc: stable@vger.kernel.org Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com> Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/1566279978-9659-1-git-send-email-xiong.y.zhang@intel.com
Ville Syrjälä [Tue, 20 Aug 2019 16:16:57 +0000 (19:16 +0300)]
drm/i915: Do not create a new max_bpc prop for MST connectors
We're not allowed to create new properties after device registration
so for MST connectors we need to either create the max_bpc property
earlier, or we reuse one we already have. Let's do the latter apporach
since the corresponding SST connector already has the prop and its
min/max are correct also for the MST connector.
The problem was highlighted by commit 4f5368b5541a ("drm/kms:
Catch mode_object lifetime errors") which results in the following
spew:
[ 1330.878941] WARNING: CPU: 2 PID: 1554 at drivers/gpu/drm/drm_mode_object.c:45 __drm_mode_object_add+0xa0/0xb0 [drm]
...
[ 1330.879008] Call Trace:
[ 1330.879023] drm_property_create+0xba/0x180 [drm]
[ 1330.879036] drm_property_create_range+0x15/0x30 [drm]
[ 1330.879048] drm_connector_attach_max_bpc_property+0x62/0x80 [drm]
[ 1330.879086] intel_dp_add_mst_connector+0x11f/0x140 [i915]
[ 1330.879094] drm_dp_add_port.isra.20+0x20b/0x440 [drm_kms_helper]
...
Cc: stable@vger.kernel.org Cc: Lyude Paul <lyude@redhat.com> Cc: sunpeng.li@amd.com Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <sean@poorly.run> Fixes: 5ca0ef8a56b8 ("drm/i915: Add max_bpc property for DP MST") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190820161657.9658-1-ville.syrjala@linux.intel.com Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com>
Chris Wilson [Wed, 21 Aug 2019 14:23:36 +0000 (15:23 +0100)]
drm/i915/execlists: Set priority hint prior to submission
Since we now run process_csb() outside of the engine->active.lock, we
can process a CS-event immediately upon our ELSP write. As we currently
inspect the pending queue *after* the ELSP write, there is an
opportunity for a CS-event to update the pending queue before we can
read it, making ourselves chases an invalid pointer.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111427 Fixes: df403069029d ("drm/i915/execlists: Lift process_csb() out of the irq-off spinlock") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190821142336.21609-1-chris@chris-wilson.co.uk
Chris Wilson [Wed, 21 Aug 2019 12:32:34 +0000 (13:32 +0100)]
drm/i915: Replace PIN_NONFAULT with calls to PIN_NOEVICT
When under severe stress for GTT mappable space, the LRU eviction model
falls off a cliff. We spend all our time scanning the much larger
non-mappable area searching for something within the mappable zone we can
evict. Turn this on its head by only using the full vma for the object if
it is already pinned in the mappable zone or there is sufficient *free*
space to accommodate it (prioritizing speedy reuse). If there is not,
immediately fall back to using small chunks (tilerow for GTT mmap, single
pages for pwrite/relocation) and using random eviction before doing a full
search.
Chris Wilson [Wed, 21 Aug 2019 04:20:44 +0000 (05:20 +0100)]
drm/i915/gtt: Relax assertion for pt_used
When inserting the final level PTE, we check that we are not overflowing
the page table (checking that pt_used does not exceed the size of the
table). However, we have to allow for every other PTE to be pinned by a
simultaneous removal thread (as on remove we bump the pt_used counter
before adjusting the table).
Dave Airlie [Wed, 21 Aug 2019 05:38:43 +0000 (15:38 +1000)]
Merge tag 'drm-misc-next-2019-08-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.4:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- dma-buf: add reservation_object_fences helper, relax
reservation_object_add_shared_fence, remove
reservation_object seq number (and then
restored)
- dma-fence: Shrinkage of the dma_fence structure,
Merge dma_fence_signal and dma_fence_signal_locked,
Store the timestamp in struct dma_fence in a union with
cb_list
Driver Changes:
- More dt-bindings YAML conversions
- More removal of drmP.h includes
- dw-hdmi: Support get_eld and various i2s improvements
- gm12u320: Few fixes
- meson: Global cleanup
- panfrost: Few refactors, Support for GPU heap allocations
- sun4i: Support for DDC enable GPIO
- New panels: TI nspire, NEC NL8048HL11, LG Philips LB035Q02,
Sharp LS037V7DW01, Sony ACX565AKM, Toppoly TD028TTEC1
Toppoly TD043MTEA1
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixup dma_resv rename fallout]
drm/i915/tgl: Move transcoders to pipes' powerwells
When trying to read registers from transcoder C and D while PG3 is ON it
causes unclaimed access warnings. Adding the powerwells for the pipes
fixes the issue, but doesn't match the spec.
Lucas De Marchi [Wed, 14 Aug 2019 23:55:17 +0000 (16:55 -0700)]
drm/i915/tgl: disable DDIC
The current SKUs added for Tiger Lake don't have DDIC hooked up, even
though it is supported by the SoC. The current state for these SKUs is
problematic since while enabling the combo phy, PORT_COMP_DW* return
0xFFFFFFFF, which is invalid per register definition.
During initialization we check what phys are not yet enabled by reading
PHY_MISC_C and try to enable it by toggling the "DE to IO Comp Pwr Down"
bit. But after that any read to the PORT_COMP_DW* returns invalid
results. This removes the following warning
We may or may not need to change the implementation to account for DDIC
being available on other SKUs. For now I think the best thing to do is
to just disable the port.
Chris Wilson [Tue, 20 Aug 2019 14:12:18 +0000 (15:12 +0100)]
drm/i915/gtt: Relax pd_used assertion
The current assertion tries to make sure that we do not over count the
number of used PDE inside a page directory -- that is with an array of
512 pde, we do not expect more than 512 elements used! However, our
assertion has to take into account that as we pin an element into the
page directory, the caller first pins the page directory so the usage
count is one higher. However, this should be one extra pin per thread,
and the upper bound is that we may have one thread for each entry.
drm/i915: Dynamically allocate s0ix struct for VLV
This is only required for a single platform so no need to reserve the
memory on all of them.
This removes the last direct dependency of i915_drv.h on i915_reg.h
(apart from the i915_reg_t definition).
v2: drop unneeded diff, keep the vlv prefix, call functions
unconditionally (Jani), fwd declaration of the struct (Chris)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190820020147.5667-1-daniele.ceraolospurio@intel.com
Michel Thierry [Sat, 17 Aug 2019 09:38:54 +0000 (02:38 -0700)]
drm/i915/tgl: Updated Private PAT programming
Gen12 removes the target-cache and age fields from the private PAT
because MOCS now have the capability to set these itself. Only memory-type
field should be programmed in the ppat, the reminded bits are reserved.
Since now there are only 4 possible combinations, we could set only 4
PPAT and leave the reminded 4 as UC, but I left them as WB as we used
to have before.
Also these registers have been relocated to the 0x4800-0x481c range.
HSDES: 1406402661
BSpec: 31654 Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-33-lucas.demarchi@intel.com
Lucas De Marchi [Sat, 17 Aug 2019 09:38:42 +0000 (02:38 -0700)]
drm/i915/tgl: Introduce initial Tiger Lake workarounds
Add empty workaround hooks for Tiger Lake. The workarounds will be added
on separate patches. We were already applying
WaRsForcewakeAddDelayForAck, which is indeed still valid, so also update
the comment.
The CSB format has been reworked for Gen12 to include information on
both the context we're switching away from and the context we're
switching to. After the change, some of the events don't have their
own bit anymore and need to be inferred from other values in the csb.
One of the context IDs (0x7FF) has also been reserved to indicate
the invalid ctx, i.e. engine idle.
Note that the full context ID includes the SW counter as well, but since
we currently only care if the context is valid or not we can ignore that
part.
v2: fix mask size, fix and expand comments (Tvrtko),
use if-ladder (Chris)
Bspec: 45555, 46144 Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190820102201.29849-1-chris@chris-wilson.co.uk
Like Gen11, Gen12 has 11 available bits for the ctx id field. However,
the last value (0x7FF) is reserved to indicate engine idle, so we
need to reduce the maximum number of contexts by 1 compared to Gen11.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190817093902.2171-29-lucas.demarchi@intel.com
Michel Thierry [Wed, 31 Jul 2019 00:49:02 +0000 (17:49 -0700)]
drm/i915/tgl: Report valid VDBoxes with SFC capability
In Gen11, only even numbered "logical" VDBoxes are hooked up to a SFC
(Scaler & Format Converter) unit. This is not the case in Tigerlake,
where each VDBox can access a SFC.
We will use this information to decide when the SFC units need to be reset
and also pass it to the GuC.
Bspec: 48077 Signed-off-by: Michel Thierry <michel.thierry@intel.com> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190731004902.34672-5-daniele.ceraolospurio@intel.com
Chris Wilson [Tue, 20 Aug 2019 08:09:07 +0000 (09:09 +0100)]
drm/i915: Serialize insertion into the file->mm.request_list
Currently, we remove the from per-file request list for throttling and
retirement under a dedicated spinlock, but insertion is governed by
struct_mutex. This needs to be the same lock so that the
retirement/insertion of neighbouring requests (at the tail) doesn't
break the list.
Imre Deak [Fri, 16 Aug 2019 09:55:23 +0000 (12:55 +0300)]
drm/i915: Sanitize PHY state during display core uninit
To work around a DMC/Punit issue on ICL where the driver's
ICL_PORT_COMP_DW8/IREFGEN PHY setting is lost when entering/exiting DC6
state, make sure to reinit the PHY whenever disabling DC states.
Similarly the driver's PHY/DBUF/CDCLK settings should have been preserved
across DC5/6 transitions, so check this on all platforms.
This gets rid of the following WARN during suspend:
Combo PHY A HW state changed unexpectedly
Chris Wilson [Mon, 19 Aug 2019 20:07:05 +0000 (21:07 +0100)]
drm/i915: Assume exclusive access to objects inside resume
Inside gtt_restore_mappings() we currently take the obj->resv->lock, but
in the future we need to avoid taking this fs-reclaim tainted lock as we
need to extend the coverage of the vm->mutex. Take advantage of the
single-threaded nature of the early resume phase, and do a single
wbinvd() to flush all the GTT objects en masse.
Chris Wilson [Mon, 19 Aug 2019 18:44:03 +0000 (19:44 +0100)]
drm/i915: Use 0 for the unordered context
Since commit 078dec3326e2 ("dma-buf: add dma_fence_get_stub") the 0
fence context became an impossible match as it is used for an always
signaled fence. We can simplify our timeline tracking by knowing that 0
always means no match.
Matt Roper [Sat, 17 Aug 2019 00:50:41 +0000 (17:50 -0700)]
drm/i915/gen11: Allow usage of all GPIO pins
Our pin mapping tables for ICP and MCC currently only list the standard
GPIO pins used for various output ports. Even through ICP's standard
pin usage only utilizes pins 1, 2, and 9-12, and MCC's standard pin
usage only uses pins 1, 2, and 9, these platforms do still have GPIO
registers to address pins in the range 1-3 and 9-14. OEM's may remap
GPIO usage in non-standard ways (and provide the actual mapping via VBT
settings), so we shouldn't exclude pins on these platforms just because
they aren't part of the standard mappings.
TGP's standard pin tables contains all the possible pins, so let's
rename them to "icp" and use them for all PCH >= PCH_ICP. This will
prevent intel_gmbus_is_valid_pin from rejecting non-standard pin usage
that an OEM specifies via the VBT.
Note that this will cause pin 9 to be labeled as "tc1" instead of "dpc"
in debug messages on platforms with the MCC PCH, but that may actually
help avoid confusion since the text strings will now be the same on all
gen11+ platforms instead of being different on just EHL.
v2: Drop now-unused MCC_DDC_BUS_DDI_* names.
v3: We want to compare against INTEL_PCH_TYPE, not INTEL_PCH_ID.
Bspec: 8417 Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Vivek Kasireddy <vivek.kasireddy@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190817005041.20651-1-matthew.d.roper@intel.com
Chris Wilson [Mon, 19 Aug 2019 07:58:19 +0000 (08:58 +0100)]
drm/i915/gt: Mark up the nested engine-pm timeline lock as irqsafe
We use a fake timeline->mutex lock to reassure lockdep that the timeline
is always locked when emitting requests. However, the use inside
__engine_park() may be inside hardirq and so lockdep now complains about
the mixed irq-state of the nested locked. Disable irqs around the
lockdep tracking to keep it happy.
Fixes: 6c69a45445af ("drm/i915/gt: Mark context->active_count as protected by timeline->mutex") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190819075835.20065-3-chris@chris-wilson.co.uk
Nishka Dasgupta [Tue, 13 Aug 2019 06:27:11 +0000 (11:57 +0530)]
drm/xen-front: Make structure fb_funcs constant
Static structure fb_funcs, of type drm_framebuffer_funcs, is used only
when it is passed to drm_gem_fb_create_with_funcs() as its last
argument. drm_gem_fb_create_with_funcs does not modify its lst argument
(fb_funcs) and hence fb_funcs is never modified. Therefore make fb_funcs
constant to protect it from further modification.
Issue found with Coccinelle.
Chris Wilson [Sat, 17 Aug 2019 23:25:11 +0000 (00:25 +0100)]
drm/i915: Propagate fence errors
Errors spread like wildfire, and must eventually be returned to the
user. They need to be captured and passed along the flow of fences,
infecting each in turn with the existing error, until finally they fall
out of a user visible result.
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:04 +0000 (09:52 +0000)]
drm/i915/uc: Never fail on HuC firmware errors
There is no need to mark whole GPU as wedged just because
of the custom HuC fw failure as users can always verify
actual HuC firmware status using existing HUC_STATUS ioctl.
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:03 +0000 (09:52 +0000)]
drm/i915/uc: Don't always fail on unavailable GuC firmware
If we failed to fetch default GuC firmware and we didn't plan
to use it for the submission and we never have used GuC before
then we may continue normal driver load, no need to declare
GPU wedged (we can use execlist for submission) and it is safe
to run without the HuC (users will check HuC status anyway).
Michal Wajdeczko [Sun, 18 Aug 2019 09:52:02 +0000 (09:52 +0000)]
drm/i915/guc: Don't open log relay if GuC is not running
As we plan to continue driver load after GuC initialization
failure, we can't assume that GuC log data will be available
just because GuC was initially enabled. We must check that
GuC is still running instead.
Nishka Dasgupta [Tue, 13 Aug 2019 06:25:48 +0000 (11:55 +0530)]
drm/vboxvideo: Make structure vbox_fb_helper_funcs constant
The static structure vbox_fb_helper_funcs, of type drm_fb_helper_funcs,
is used only when it is passed as the third argument to
drm_fb_helper_fbdev_setup(), which does not modify it. Hence make it
constant to protect it from unintended modifications.
Issue found with Coccinelle.
Chris Wilson [Sat, 17 Aug 2019 15:30:22 +0000 (16:30 +0100)]
dma-fence: Store the timestamp in the same union as the cb_list
The timestamp and the cb_list are mutually exclusive, the cb_list can
only be added to prior to being signaled (and once signaled we drain),
while the timestamp is only valid upon being signaled. Both the
timestamp and the cb_list are only valid while the fence is alive, and
as soon as no references are held can be replaced by the rcu_head.
By reusing the union for the timestamp, we squeeze the base dma_fence
struct to 64 bytes on x86-64.
Chris Wilson [Sat, 17 Aug 2019 15:23:00 +0000 (16:23 +0100)]
dma-fence: Simply wrap dma_fence_signal_locked with dma_fence_signal
Currently dma_fence_signal() tries to avoid the spinlock and only takes
it if absolutely required to walk the callback list. However, to allow
for some users to surreptitiously insert lazy signal callbacks that
do not depend on enabling the signaling mechanism around every fence,
we always need to notify the callbacks on signaling. As such, we will
always need to take the spinlock and dma_fence_signal() effectively
becomes a clone of dma_fence_signal_locked().
v2: Update the test_and_set_bit() before entering the spinlock.
v3: Drop the test_[and_set]_bit() before the spinlock, it's a caller
error so expected to be very unlikely.
Chris Wilson [Sat, 17 Aug 2019 14:47:34 +0000 (15:47 +0100)]
dma-fence: Avoid list_del during fence->cb_list iteration
Before we notify the fence signal callback, we remove the cb from the
list. However, since we are processing the entire list from underneath
the spinlock, we do not need to individual delete each element, but can
simply reset the link and the entire list.
Chris Wilson [Sat, 17 Aug 2019 14:47:33 +0000 (15:47 +0100)]
dma-fence: Shrink size of struct dma_fence
Rearrange the couple of 32-bit atomics hidden amongst the field of
pointers that unnecessarily caused the compiler to insert some padding,
shrinks the size of the base struct dma_fence from 80 to 72 bytes on
x86-64.
Michal Wajdeczko [Sat, 17 Aug 2019 13:11:43 +0000 (13:11 +0000)]
drm/i915/uc: Cleanup fw fetch on every GuC/HuC init failure
Be consistent and always perform fw fetch cleanup in GuC/HuC specific
init functions on every failure. Also while converting firmware
status to error, stop treating SELECTED as non-error, as long term
we should not see it.
Michal Wajdeczko [Sat, 17 Aug 2019 13:11:42 +0000 (13:11 +0000)]
drm/i915/uc: Cleanup fw fetch only if it was successful
We can rely on firmware status AVAILABLE to determine if any
firmware cleanup is required. Also don't unconditionally reset
fw status to SELECTED as we will loose MISSING/ERROR codes.
Chris Wilson [Sat, 17 Aug 2019 07:37:11 +0000 (08:37 +0100)]
drm/i915/selftests: Check the context size
Add a redzone to our context image and check the HW does not write into
after a context save, to verify that we have the correct context size.
(This does vary with feature bits, so test with a live setup that should
match how we run userspace.)
v2: Check the redzone on every context unpin
v3: Use a kernel context to prevent loading garbage for ringbuffer
submission
Mika Kuoppala [Fri, 16 Aug 2019 09:47:54 +0000 (12:47 +0300)]
drm/i915/gtt: Fold gen8 insertions into one
As we give page directory pointer (lvl 3) structure
for pte insertion, we can fold both versions into
one function by teaching it to get pdp regardless
of top level.
Michal Wajdeczko [Fri, 16 Aug 2019 20:56:58 +0000 (20:56 +0000)]
drm/i915/uc: Add explicit DISABLED state for firmware
We really need to have separate NOT_SUPPORTED state (for
lack of hardware support) and DISABLED state (to indicate
user decision) as we will have to take special steps even
if GuC firmware is now disabled but hardware exists and
could have been previously used.
v2: fix logic (Chris/CI)
v3: use proper check to avoid probe failure (CI)
v4: explain status transitions (Chris)
To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.
Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Chris Wilson [Fri, 16 Aug 2019 17:16:08 +0000 (18:16 +0100)]
drm/i915/execlists: Lift process_csb() out of the irq-off spinlock
If we only call process_csb() from the tasklet, though we lose the
ability to bypass ksoftirqd interrupt processing on direct submission
paths, we can push it out of the irq-off spinlock.
The penalty is that we then allow schedule_out to be called concurrently
with schedule_in requiring us to handle the usage count (baked into the
pointer itself) atomically.
As we do kick the tasklets (via local_bh_enable()) after our submission,
there is a possibility there to see if we can pull the local softirq
processing back from the ksoftirqd.
v2: Store the 'switch_priority_hint' on submission, so that we can
safely check during process_csb().
Laurent Pinchart [Fri, 16 Aug 2019 12:22:28 +0000 (15:22 +0300)]
drm/omap: displays: Remove unused panel drivers
drm_panel-based drivers for the ACX565AKM, LB035Q02, LS037V7DW01,
NL8048HL11, TD028TTEC1 and TD043MTEA1 are available, remove the
omapdrm-specific drivers.
Laurent Pinchart [Fri, 16 Aug 2019 12:22:27 +0000 (15:22 +0300)]
video: omapfb2: Make standard and custom panel drivers mutually exclusive
Standard DRM panel drivers for several panels used by omapfb2 are now
available. Their module name clashes with the modules from
drivers/video/fbdev/omap2/omapfb/displays, part of the deprecated omapfb2
fbdev driver. As omapfb2 can only be compiled when the omapdrm driver is
disabled, and the DRM panel drivers are useless in that case, make the
omapfb2 panels depend on the standard DRM panels being disabled to fix
the name clash.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Fixes: dc2e1e5b279966 ("drm/panel: Add driver for the Toppoly TD043MTEA1 panel") Fixes: 415b8dd0871188 ("drm/panel: Add driver for the Toppoly TD028TTEC1 panel") Fixes: 1c8fc3f0c5d280 ("drm/panel: Add driver for the Sony ACX565AKM panel") Fixes: c9cf4c2a3bd35f ("drm/panel: Add driver for the Sharp LS037V7DW01 panel") Fixes: df439abe650177 ("drm/panel: Add driver for the NEC NL8048HL11 panel") Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> [added tags] Link: https://patchwork.freedesktop.org/patch/msgid/20190816122228.9475-2-laurent.pinchart@ideasonboard.com
Chris Wilson [Fri, 16 Aug 2019 12:10:00 +0000 (13:10 +0100)]
drm/i915: Markup expected timeline locks for i915_active
As every i915_active_request should be serialised by a dedicated lock,
i915_active consists of a tree of locks; one for each node. Markup up
the i915_active_request with what lock is supposed to be guarding it so
that we can verify that the serialised updated are indeed serialised.
Chris Wilson [Fri, 16 Aug 2019 12:09:59 +0000 (13:09 +0100)]
drm/i915/gt: Mark context->active_count as protected by timeline->mutex
We use timeline->mutex to protect modifications to
context->active_count, and the associated enable/disable callbacks.
Due to complications with engine-pm barrier there is a path where we used
a "superlock" to provide serialised protect and so could not
unconditionally assert with lockdep that it was always held. However,
we can mark the mutex as taken (noting that we may be nested underneath
ourselves) which means we can be reassured the right timeline->mutex is
always treated as held and let lockdep roam free.
Michal Wajdeczko [Fri, 16 Aug 2019 10:54:59 +0000 (10:54 +0000)]
drm/i915/wopcm: Try to use already locked WOPCM layout
If WOPCM layout is already locked in HW we shouldn't continue
with our own partitioning as it could be likely different and
we will be unable to enforce it and fail. Instead we should try
to reuse what is already programmed, maybe there will be a fit.
This should enable us to reload driver with slightly different
HuC firmware (or even without HuC) without need to reboot.
v2: reordered/rebased
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Michal Winiarski <michal.winiarski@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190816105501.31020-4-michal.wajdeczko@intel.com
Michał Winiarski [Fri, 16 Aug 2019 10:54:57 +0000 (10:54 +0000)]
drm/i915/uc: Move FW size sanity check back to fetch
While we need to know WOPCM size to do this sanity check, it has more to
do with FW than with WOPCM. Let's move the check to fetch phase, it's
not like WOPCM is going to grow in the meantime.
v2: rebased
v3: use __intel_uc_fw_get_upload_size (Daniele)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jackie Li <yaodong.li@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190816105501.31020-2-michal.wajdeczko@intel.com
Matthew Auld [Fri, 16 Aug 2019 10:53:57 +0000 (11:53 +0100)]
drm/i915/buddy: use kmemleak_update_trace
Since nodes are cached in a free-list, and potentially marked as free
without actually being destroyed, thus allowing them to be
opportunistically re-allocated, we should apply kmemleak_update_trace
every time a node is given a new owner and marked as allocated, to aid
in debugging.
Fabrizio Castro [Fri, 2 Aug 2019 07:34:05 +0000 (08:34 +0100)]
drm: rcar-du: lvds: Fix bridge_to_rcar_lvds
Using name "bridge" for macro bridge_to_rcar_lvds argument doesn't
work when the pointer name used by the caller is not "bridge".
Rename the argument to "b" to allow for any pointer name.
While at it, fix the connector_to_rcar_lvds macro similarly.
Laurent Pinchart [Wed, 17 Jan 2018 14:16:48 +0000 (16:16 +0200)]
drm: Remove bridge support from legacy helpers
DRM bridges are only used by atomic drivers, and none of them use the
legacy helpers. Drop bridge support from those helpers to prepare for
making the bridge operations atomic-aware.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Sean Paul <seanpaul@chromium.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Laurent Pinchart [Wed, 17 Jan 2018 13:54:15 +0000 (15:54 +0200)]
drm: Don't include drm/drm_encoder_slave.h when not needed
The dw-hdmi, kirin and imx drivers include the drm/drm_encoder_slave.h
header but don't use the encoder slave API. Remove it or replace it with
drm/drm_encoder.h as needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Wed, 14 Aug 2019 18:24:01 +0000 (19:24 +0100)]
dma-buf: Restore seqlock around dma_resv updates
This reverts 67c97fb79a7f ("dma-buf: add reservation_object_fences helper") dd7a7d1ff2f1 ("drm/i915: use new reservation_object_fences helper") 0e1d8083bddb ("dma-buf: further relax reservation_object_add_shared_fence") 5d344f58da76 ("dma-buf: nuke reservation_object seq number")
The scenario that defeats simply grabbing a set of shared/exclusive
fences and using them blissfully under RCU is that any of those fences
may be reallocated by a SLAB_TYPESAFE_BY_RCU fence slab cache. In this
scenario, while keeping the rcu_read_lock we need to establish that no
fence was changed in the dma_resv after a read (or full) memory barrier.
Chris Wilson [Fri, 16 Aug 2019 07:46:35 +0000 (08:46 +0100)]
drm/i915: Extract intel_frontbuffer active tracking
Move the active tracking for the frontbuffer operations out of the
i915_gem_object and into its own first class (refcounted) object. In the
process of detangling, we switch from low level request tracking to the
easier i915_active -- with the plan that this avoids any potential
atomic callbacks as the frontbuffer tracking wishes to sleep as it
flushes.
Chris Wilson [Thu, 15 Aug 2019 20:57:09 +0000 (21:57 +0100)]
drm/i915: Protect request retirement with timeline->mutex
Forgo the struct_mutex requirement for request retirement as we have
been transitioning over to only using the timeline->mutex for
controlling the lifetime of a request on that timeline.
Chris Wilson [Thu, 15 Aug 2019 20:57:08 +0000 (21:57 +0100)]
drm/i915/gt: Guard timeline pinning without relying on struct_mutex
In preparation for removing struct_mutex from around context retirement,
we need to make timeline pinning and unpinning safe. Since multiple
engines/contexts can share a single timeline, we cannot rely on
borrowing the context mutex (otherwise we could state that the timeline
is only pinned/unpinned inside the context pin/unpin and so guarded by
it). However, we only perform a sequence of atomic operations inside the
timeline pin/unpin and the sequence of those operations is safe for a
concurrent unpin / pin, so we can relax the struct_mutex requirement.
Chris Wilson [Thu, 15 Aug 2019 20:57:07 +0000 (21:57 +0100)]
drm/i915/gt: Convert timeline tracking to spinlock
Convert the active_list manipulation of timelines to use spinlocks so
that we can perform the updates from underneath a quick interrupt
callback, if need be.
Chris Wilson [Thu, 15 Aug 2019 04:20:30 +0000 (05:20 +0100)]
drm/i915: Move tasklet kicking to __i915_request_queue caller
Since __i915_request_queue() may be called from hardirq (timer) context,
we cannot use local_bh_disable/enable at the lower level. As we do want
to kick the tasklet to speed up initial submission or preemption for
normal client submission, lift it to the normal process context
callpath.
Mika Kuoppala [Thu, 15 Aug 2019 09:49:29 +0000 (12:49 +0300)]
drm/i915/icl: Add gen11 specific render breadcrumbs
Flush according to what gen11 expects when writing
breadcrumbs. As only the seqnowrite + flush differs
between engine and gens, enclose the footer to
helper.
v2: avoid problem of sane local naming by not using them
Mika Kuoppala [Thu, 15 Aug 2019 08:30:53 +0000 (11:30 +0300)]
drm/i915/icl: Implement gen11 flush including tile cache
Add tile cache flushing for gen11. To relive us from the
burden of previous obsolete workarounds, make a dedicated
flush/invalidate callback for gen11.
To fortify an independent single flush, do post
sync op as there are indications that without it
we don't flush everything. This should also make this
callback more readily usable in tgl (see l3 fabric flush).
projects / kernel.git / log