Sherry Sun [Mon, 25 Jul 2022 05:01:15 +0000 (13:01 +0800)]
tty: serial: fsl_lpuart: correct the count of break characters
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.
Fixes: ee10bc2bc733 ("serial: fsl_lpuart: handle break and make sysrq work") Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Dooks [Thu, 21 Jul 2022 21:24:30 +0000 (22:24 +0100)]
serial: stm32: make info structs static to avoid sparse warnings
The info structs are local only to the stm32-usart.c driver and are
triggering sparse warnings about being undecalred. Move these into
the main driver code and make them static to avoid the following
warnings:
drivers/tty/serial/stm32-usart.h:42:25: warning: symbol 'stm32f4_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:63:25: warning: symbol 'stm32f7_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:85:25: warning: symbol 'stm32h7_info' was not declared. Should it be static?
Shenwei Wang [Thu, 14 Jul 2022 18:58:58 +0000 (13:58 -0500)]
serial: fsl_lpuart: zero out parity bit in CS7 mode
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
In the logic around call to clk_round_rate(), for some corner conditions,
get_clk_div_rate() could return an sub-optimal clock rate. Also, if an
exact clock rate was not found lowest clock was being returned.
Search for suitable clock rate in 2 steps
a) exact match or within 2% tolerance
b) within 5% tolerance
This also takes care of corner conditions.
Fixes: 75193b359c97 ("tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate") Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com> Link: https://lore.kernel.org/r/1657911343-1909-1-git-send-email-quic_vnivarth@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Currently the documentation claims that a maximum of 1000 msecs is allowed
for RTS delays. However nothing actually checks the values read from device
tree/ACPI and so it is possible to set much higher values.
There is already a maximum of 100 ms enforced for RTS delays that are set
via the UART TIOCSRS485 ioctl. To be consistent with that use the same
limit for DT/ACPI values.
Although this change is visible to userspace the risk of breaking anything
when reducing the max delays from 1000 to 100 ms should be very low, since
100 ms is already a very high maximum for delays that are usually rather in
the usecs range.
serial: core: sanitize RS485 delays read from device tree
Currently the RTS delays set via device tree are not clamped to a maximum
value although the device tree bindings documentation for RS485 claims that
only a maximum of 1000 msecs is allowed.
So clamp the values to avoid arbitrary high delay settings. However clamp
the values to 100 instead of 1000 msecs to be consistent which the maximum
that is allowed when setting the delays from userspace via the UART ioctl
TIOCSRS485.
serial: core, 8250: set RS485 termination GPIO in serial core
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
serial: ar933x: Remove superfluous code in ar933x_config_rs485()
In ar933x_config_rs485() the check for the RTS GPIO is not needed since in
case the GPIO is not available at driver init ar933x_no_rs485 is assigned
to port->rs485_supported and this function is never called. So remove the
check.
Also in uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port. So remove the assignment in the
drivers rs485_config() function to avoid redundancy.
RS485 is not possible without an RTS GPIO regardless of whether RS485 is
enabled at boot time or not. So correct the concerning check in the probe()
function.
serial: 8250_bcm7271: Save/restore RTS in suspend/resume
Commit 63e0f239159d ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.
serial: 8250_dw: Avoid pslverr on reading empty receiver fifo
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
serial: 8250: SERIAL_8250_ASPEED_VUART should depend on ARCH_ASPEED
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
Cameron Williams [Mon, 11 Jul 2022 15:35:10 +0000 (16:35 +0100)]
tty: 8250: Add support for Brainboxes PX cards.
Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.
Daniel Starke [Thu, 7 Jul 2022 11:32:22 +0000 (13:32 +0200)]
tty: n_gsm: fix flow control handling in tx path
The current implementation constipates all transmission paths during flow
control except for flow control frames. However, these may not be located
at the beginning of the transmission queue of the control channel.
Ensure that flow control frames in the transmission queue for the control
channel are always handled even if constipated by skipping through other
messages.
Daniel Starke [Thu, 7 Jul 2022 11:32:21 +0000 (13:32 +0200)]
tty: n_gsm: fix DM command
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.
Daniel Starke [Thu, 7 Jul 2022 11:32:20 +0000 (13:32 +0200)]
tty: n_gsm: fix wrong T1 retry count handling
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.
serial: 8250_fsl: Don't report FE, PE and OE twice
Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.
So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.
To weaken this problem restrict saving LSR to only the BI bit.
Note however that the handling is still broken:
- lsr_saved_flags is updated using orig_lsr which is the LSR content
for the first received char, but there might be more in the FIFO, so
a character is thrown away that is received later and not necessarily
the one following the break.
- The doubled break might be the 2nd and 3rd char in the FIFO, so the
workaround doesn't catch these, because serial8250_rx_chars() doesn't
handle the workaround.
- lsr_saved_flags might have set UART_LSR_BI at the entry of
fsl8250_handle_irq() which doesn't originate from
fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
- For a long or a short break this isn't about two characters, but more
or only a single one.
Daniel Starke [Fri, 1 Jul 2022 12:23:32 +0000 (14:23 +0200)]
tty: n_gsm: fix resource allocation order in gsm_activate_mux()
Within gsm_activate_mux() all timers and locks are initiated before the
actual resource for the control channel is allocated. This can lead to race
conditions.
Allocate the control channel DLCI object first to avoid race conditions.
Daniel Starke [Fri, 1 Jul 2022 12:23:31 +0000 (14:23 +0200)]
tty: n_gsm: fix deadlock and link starvation in outgoing data path
The current implementation queues up new control and user packets as needed
and processes this queue down to the ldisc in the same code path.
That means that the upper and the lower layer are hard coupled in the code.
Due to this deadlocks can happen as seen below while transmitting data,
especially during ldisc congestion. Furthermore, the data channels starve
the control channel on high transmission load on the ldisc.
Introduce an additional control channel data queue to prevent timeouts and
link hangups during ldisc congestion. This is being processed before the
user channel data queue in gsm_data_kick(), i.e. with the highest priority.
Put the queue to ldisc data path into a workqueue and trigger it whenever
new data has been put into the transmission queue. Change
gsm_dlci_data_sweep() accordingly to fill up the transmission queue until
TX_THRESH_HI. This solves the locking issue, keeps latency low and provides
good performance on high data load.
Note that now all packets from a DLCI are removed from the internal queue
if the associated DLCI was closed. This ensures that no data is sent by the
introduced write task to an already closed DLCI.
Daniel Starke [Fri, 1 Jul 2022 06:16:52 +0000 (08:16 +0200)]
tty: n_gsm: fix race condition in gsmld_write()
The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Daniel Starke [Fri, 1 Jul 2022 06:16:50 +0000 (08:16 +0200)]
tty: n_gsm: fix packet re-transmission without open control channel
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Daniel Starke [Fri, 1 Jul 2022 06:16:48 +0000 (08:16 +0200)]
tty: n_gsm: fix non flow control frames during mux flow off
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Daniel Starke [Fri, 1 Jul 2022 06:16:47 +0000 (08:16 +0200)]
tty: n_gsm: fix missing timer to handle stalled links
The current implementation does not handle the situation that no data is in
the internal queue and needs to be sent out while the user tty fifo is
full.
Add a timer that moves more data from user tty down to the internal queue
which is then serialized on the ldisc. This timer is triggered if no data
was moved from a user tty to the internal queue within 10 * T1.
Daniel Starke [Fri, 1 Jul 2022 06:16:46 +0000 (08:16 +0200)]
tty: n_gsm: fix wrong queuing behavior in gsm_dlci_data_output()
1) The function drains the fifo for the given user tty/DLCI without
considering 'TX_THRESH_HI' and different to gsm_dlci_data_output_framed(),
which moves only one packet from the user side to the internal transmission
queue. We can only handle one packet at a time here if we want to allow
DLCI priority handling in gsm_dlci_data_sweep() to avoid link starvation.
2) Furthermore, the additional header octet from convergence layer type 2
is not counted against MTU. It is part of the UI/UIH frame message which
needs to be limited to MTU. Hence, it is wrong not to consider this octet.
3) Finally, the waiting user tty is not informed about freed space in its
send queue.
Take at most one packet worth of data out of the DLCI fifo to fix 1).
Limit the max user data size per packet to MTU - 1 in case of convergence
layer type 2 to leave space for the control signal octet which is added in
the later part of the function. This fixes 2).
Add tty_port_tty_wakeup() to wake up the user tty if new write space has
been made available to fix 3).
Daniel Starke [Fri, 1 Jul 2022 06:16:45 +0000 (08:16 +0200)]
tty: n_gsm: fix tty registration before control channel open
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Daniel Starke [Fri, 1 Jul 2022 06:16:44 +0000 (08:16 +0200)]
tty: n_gsm: fix user open not possible at responder until initiator open
After setting up the control channel on both sides the responder side may
want to open a virtual tty to listen on until the initiator starts an
application on a user channel. The current implementation allows the
open() but no other operation, like termios. These fail with EINVAL.
The responder sided application has no means to detect an open by the
initiator sided application this way. And the initiator sided applications
usually expect the responder sided application to listen on the user
channel upon open.
Set the user channel into half-open state on responder side once a user
application opens the virtual tty to allow IO operations on it.
Furthermore, keep the user channel constipated until the initiator side
opens it to give the responder sided application the chance to detect the
new connection and to avoid data loss if the responder sided application
starts sending before the user channel is open.
Andy Shevchenko [Thu, 30 Jun 2022 10:05:07 +0000 (13:05 +0300)]
serial: 8250_dw: Drop PM ifdeffery
Drop CONFIG_PM and CONFIG_PM_SLEEP ifdeffery while converting dw8250_pm_ops
to use new PM macros. Since we are using runtime PM, wrap dw8250_pm_ops into
pm_ptr().
Andy Shevchenko [Thu, 30 Jun 2022 09:38:16 +0000 (12:38 +0300)]
serial: 8250_dw: Sort headers alphabetically
For the sake of better maintenance, sort included headers alphabetically.
While at it, split the serial group of headers which makes clear the
subsystem the driver belongs to.
Michael Walle [Tue, 28 Jun 2022 12:07:05 +0000 (14:07 +0200)]
earlycon: prevent multiple register_console()
If the earlycon parameter is given twice, the kernel will spit out a
WARN() in register_console() because it was already registered. The
non-dt variant setup_earlycon() already handles that gracefully. The dt
variant of_setup_earlycon() doesn't. Add the check there and add the
-EALREADY handling in early_init_dt_scan_chosen_stdout().
FWIW, this doesn't happen if CONFIG_ACPI_SPCR_TABLE is set. In that case
the registration is delayed until after earlycon parameter(s) are
parsed.
Chanho Park [Wed, 29 Jun 2022 00:41:41 +0000 (09:41 +0900)]
tty: serial: samsung_tty: loopback mode support
Internal loopback mode can be supported by setting
UCON register's Loopback Mode bit. The mode & bit can be supported
since s3c2410 and later SoCs. The prefix of LOOPBACK / BIT(5) naming
should be also changed to S3C2410_ in order to avoid confusion.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Link: https://lore.kernel.org/r/20220629004141.51484-1-chanho61.park@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chanho Park [Wed, 29 Jun 2022 00:55:38 +0000 (09:55 +0900)]
tty: serial: samsung_tty: support more than 4 uart ports
Regarding Exynos Auto v9 SoC, it supports uarts up to 12. However, the
maximum number of the ports has been derived from
CONFIG_SERIAL_SAMSUNG_UARTS and tightly coupled with the config for
previous Samsung SoCs such as s3c24xx and s3c64xx. To overcome this
limitation, this changes the usage of the definition to UART_NR which is
widely used from other serial drivers. This also defines the value to 12
only for ARM64 SoCs to not affect the change to previous arm32 SoCs.
Instead of enumerating all the ports as predefined arrays, this
introduces s3c24xx_serial_init_port_default that is initializing the
structure as the default value.
Reviewed-by: Hector Martin <marcan@marcan.st> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Chanho Park <chanho61.park@samsung.com> Link: https://lore.kernel.org/r/20220629005538.60132-1-chanho61.park@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilpo Järvinen [Fri, 24 Jun 2022 20:42:10 +0000 (23:42 +0300)]
serial: 8250_dwlib: Support for 9th bit multipoint addressing
Add 9th bit multipoint addressing mode for DW UART. 9th bit addressing
can be used only when HW RS485 is available.
Updating RAR (receive address register) is bit tricky because busy
indication is not be available when DW UART is strictly 16550
compatible, which is the case with the hardware I was testing with. RAR
should not be updated while receive is in progress which is now
achieved by deasserting RE and waiting for one frame (in case rx would
be in progress, the driver seems to have no way of knowing it w/o busy
indication). Because of this complexity, it's better to avoid doing it
unless really needed.
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Co-developed-by: Raymond Tan <raymond.tan@intel.com> Co-developed-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Raymond Tan <raymond.tan@intel.com> Signed-off-by: Lakshmi Sowjanya <lakshmi.sowjanya.d@intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220624204210.11112-7-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilpo Järvinen [Fri, 24 Jun 2022 20:42:09 +0000 (23:42 +0300)]
serial: Support for RS-485 multipoint addresses
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Ilpo Järvinen [Fri, 24 Jun 2022 20:42:07 +0000 (23:42 +0300)]
serial: 8250_lpss: Use 32-bit reads
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Ilpo Järvinen [Fri, 24 Jun 2022 20:42:05 +0000 (23:42 +0300)]
serial: 8250: make saved LSR larger
DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.
Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.
Ilpo Järvinen [Fri, 24 Jun 2022 20:54:20 +0000 (23:54 +0300)]
serial: msm: Rename UART_* defines to MSM_UART_*
Using UART_* to name defines is a bit problematic. When trying to do
unrelated cleanup which also involved tweaking header inclusion logic,
caused UART_CSR from serial_reg.h to leak into msm's namespace which is
also among msm defines. Thus, rename all UART_* ones to MSM_UART_* to
eliminate possibility of collisions.
Claudiu Beznea [Thu, 16 Jun 2022 14:00:23 +0000 (17:00 +0300)]
tty: serial: atmel: remove enable/disable clock due to atmel_console_setup()
There is no need for clk_prepare_enable() at the beginning of
atmel_console_setup() and clk_disable_unprepare() at the end of
atmel_console_setup() as the clock is already enabled when calling
atmel_console_setup() and its disablement is done at the end
of probe.
Claudiu Beznea [Thu, 16 Jun 2022 14:00:21 +0000 (17:00 +0300)]
tty: serial: atmel: stop using legacy pm ops
Stop using legacy PM ops and switch using dev_pm_ops. Along with
it #ifdef CONFIG_PM are removed and __maybe_unused and pm_ptr() used
instead. Coding style recommends (at chapter Conditional Compilation)
to avoid using preprocessor conditional and use __maybe_unused
instead.
Liang He [Wed, 15 Jun 2022 11:17:47 +0000 (19:17 +0800)]
drivers: tty: serial: Add missing of_node_put() in serial-tegra.c
In tegra_uart_init(), of_find_matching_node() will return a node
pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Ilpo Järvinen [Mon, 13 Jun 2022 11:39:05 +0000 (14:39 +0300)]
serial: Drop timeout from uart_port
Since commit cf5023c57065 ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.
Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Jiri Slaby [Tue, 14 Jun 2022 09:05:36 +0000 (11:05 +0200)]
tty/vt: consolemap: remove dflt reset from con_do_clear_unimap()
con_do_clear_unimap() sets dflt to NULL and then calls
con_release_unimap() which does the very same as the first thing. So
remove the former as it is apparently superfluous.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220614090537.15557-7-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use FIELD_GET() and GENMASK() helpers instead of direct shifts and ANDs.
This makes the code even more obvious. I didn't know about the helpers
at the time of writing the macros.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220614090537.15557-6-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a follow-up to the commit b6044fa84377 (tty/vt: consolemap: rename
and document struct uni_pagedir), rename also the members of struct
vc_data. I.e. pagedir -> pagedict. And while touching all the places,
remove also the unnecessary vc_ prefix.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220614090537.15557-5-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Slaby [Tue, 14 Jun 2022 09:05:33 +0000 (11:05 +0200)]
tty/vt: consolemap: saner variable names in set_inverse_transl()
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Jiri Slaby [Tue, 14 Jun 2022 09:05:30 +0000 (11:05 +0200)]
tty/vt: consolemap: use ARRAY_SIZE(), part II.
The code still uses constants (macros) as bounds in loops after commit 11693f7641be (tty/vt: consolemap: use ARRAY_SIZE()). The contants are at
least macros used also in the definition of the arrays. But use
ARRAY_SIZE() on two more places to ensure the loops never run out of
bounds even if the array definition change.
Linus Torvalds [Sun, 19 Jun 2022 14:58:28 +0000 (09:58 -0500)]
Merge tag 'x86-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- Make RESERVE_BRK() work again with older binutils. The recent
'simplification' broke that.
- Make early #VE handling increment RIP when successful.
- Make the #VE code consistent vs. the RIP adjustments and add
comments.
- Handle load_unaligned_zeropad() across page boundaries correctly in
#VE when the second page is shared.
* tag 'x86-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tdx: Handle load_unaligned_zeropad() page-cross to a shared page
x86/tdx: Clarify RIP adjustments in #VE handler
x86/tdx: Fix early #VE handling
x86/mm: Fix RESERVE_BRK() for older binutils
Linus Torvalds [Sun, 19 Jun 2022 14:54:16 +0000 (09:54 -0500)]
Merge tag 'objtool-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull build tooling updates from Thomas Gleixner:
- Remove obsolete CONFIG_X86_SMAP reference from objtool
- Fix overlapping text section failures in faddr2line for real
- Remove OBJECT_FILES_NON_STANDARD usage from x86 ftrace and replace it
with finegrained annotations so objtool can validate that code
correctly.
* tag 'objtool-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ftrace: Remove OBJECT_FILES_NON_STANDARD usage
faddr2line: Fix overlapping text section failures, the sequel
objtool: Fix obsolete reference to CONFIG_X86_SMAP
Linus Torvalds [Sun, 19 Jun 2022 14:51:00 +0000 (09:51 -0500)]
Merge tag 'sched-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single scheduler fix plugging a race between sched_setscheduler()
and balance_push().
sched_setscheduler() spliced the balance callbacks accross a lock
break which makes it possible for an interleaving schedule() to
observe an empty list"
* tag 'sched-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix balance_push() vs __sched_setscheduler()
Linus Torvalds [Sun, 19 Jun 2022 14:47:41 +0000 (09:47 -0500)]
Merge tag 'locking-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull lockdep fix from Thomas Gleixner:
"A RT fix for lockdep.
lockdep invokes prandom_u32() to create cookies. This worked until
prandom_u32() was switched to the real random generator, which takes a
spinlock for extraction, which does not work on RT when invoked from
atomic contexts.
lockdep has no requirement for real random numbers and it turns out
sched_clock() is good enough to create the cookie. That works
everywhere and is faster"
* tag 'locking-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Use sched_clock() for random numbers
- Add a missing compatible string to the Uniphier driver"
* tag 'irq-urgent-2022-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/loongson-liointc: Use architecture register to get coreid
irqchip/uniphier-aidet: Add compatible string for NX1 SoC
dt-bindings: interrupt-controller/uniphier-aidet: Add bindings for NX1 SoC
irqchip/realtek-rtl: Fix refcount leak in map_interrupts
irqchip/gic-v3: Fix refcount leak in gic_populate_ppi_partitions
irqchip/gic-v3: Fix error handling in gic_populate_ppi_partitions
irqchip/apple-aic: Fix refcount leak in aic_of_ic_init
irqchip/apple-aic: Fix refcount leak in build_fiq_affinity
irqchip/gic/realview: Fix refcount leak in realview_gic_of_init
irqchip/xilinx: Remove microblaze+zynq dependency
genirq: PM: Use runtime PM for chained interrupts
Linus Torvalds [Sun, 19 Jun 2022 14:37:29 +0000 (09:37 -0500)]
Merge tag 'char-misc-5.19-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes for real from Greg KH:
"Let's tag the proper branch this time...
Here are some small char/misc driver fixes for 5.19-rc3 that resolve
some reported issues.
They include:
- mei driver fixes
- comedi driver fix
- rtsx build warning fix
- fsl-mc-bus driver fix
All of these have been in linux-next for a while with no reported
issues"
This is what the merge in commit a24f1f815404 _should_ have merged, but
Greg fat-fingered the pull request and I got some small changes from
linux-next instead there. Credit to Nathan Chancellor for eagle-eyes.
Link: https://lore.kernel.org/all/Yqywy+Md2AfGDu8v@dev-arch.thelio-3990X/
* tag 'char-misc-5.19-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
bus: fsl-mc-bus: fix KASAN use-after-free in fsl_mc_bus_remove()
mei: me: add raptor lake point S DID
mei: hbm: drop capability response on early shutdown
mei: me: set internal pg flag to off on hardware reset
misc: rtsx: Fix clang -Wsometimes-uninitialized in rts5261_init_from_hw()
comedi: vmk80xx: fix expression for tx buffer size
Linus Torvalds [Sun, 19 Jun 2022 14:35:09 +0000 (09:35 -0500)]
Merge tag 'i2c-for-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"MAINTAINERS rectifications and a few minor driver fixes"
* tag 'i2c-for-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mediatek: Fix an error handling path in mtk_i2c_probe()
i2c: designware: Use standard optional ref clock implementation
MAINTAINERS: core DT include belongs to core
MAINTAINERS: add include/dt-bindings/i2c to I2C SUBSYSTEM HOST DRIVERS
i2c: npcm7xx: Add check for platform_driver_register
MAINTAINERS: Update Synopsys DesignWare I2C to Supported
Linus Torvalds [Sun, 19 Jun 2022 14:24:49 +0000 (09:24 -0500)]
Merge tag 'xfs-5.19-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"There's not a whole lot this time around (I'm still on vacation) but
here are some important fixes for new features merged in -rc1:
- Fix a bug where inode flag changes would accidentally drop nrext64
- Fix a race condition when toggling LARP mode"
* tag 'xfs-5.19-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: preserve DIFLAG2_NREXT64 when setting other inode attributes
xfs: fix variable state usage
xfs: fix TOCTOU race involving the new logged xattrs control knob
Linus Torvalds [Sun, 19 Jun 2022 02:51:12 +0000 (21:51 -0500)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a variety of bugs, many of which were found by folks using fuzzing
or error injection.
Also fix up how test_dummy_encryption mount option is handled for the
new mount API.
Finally, fix/cleanup a number of comments and ext4 Documentation
files"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix a doubled word "need" in a comment
ext4: add reserved GDT blocks check
ext4: make variable "count" signed
ext4: correct the judgment of BUG in ext4_mb_normalize_request
ext4: fix bug_on ext4_mb_use_inode_pa
ext4: fix up test_dummy_encryption handling for new mount API
ext4: use kmemdup() to replace kmalloc + memcpy
ext4: fix super block checksum incorrect after mount
ext4: improve write performance with disabled delalloc
ext4: fix warning when submitting superblock in ext4_commit_super()
ext4, doc: remove unnecessary escaping
ext4: fix incorrect comment in ext4_bio_write_page()
fs: fix jbd2_journal_try_to_free_buffers() kernel-doc comment
Linus Torvalds [Sun, 19 Jun 2022 02:44:44 +0000 (21:44 -0500)]
Merge tag '5.19-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
"Two cifs debugging improvements - one found to deal with debugging a
multichannel problem and one for a recent fallocate issue
This does include the two larger multichannel reconnect (dynamically
adjusting interfaces on reconnect) patches, because we recently found
an additional problem with multichannel to one server type that I want
to include at the same time"
* tag '5.19-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: when a channel is not found for server, log its connection id
smb3: add trace point for SMB2_set_eof
Zhang Yi [Wed, 1 Jun 2022 09:27:17 +0000 (17:27 +0800)]
ext4: add reserved GDT blocks check
We capture a NULL pointer issue when resizing a corrupt ext4 image which
is freshly clear resize_inode feature (not run e2fsck). It could be
simply reproduced by following steps. The problem is because of the
resize_inode feature was cleared, and it will convert the filesystem to
meta_bg mode in ext4_resize_fs(), but the es->s_reserved_gdt_blocks was
not reduced to zero, so could we mistakenly call reserve_backup_gdb()
and passing an uninitialized resize_inode to it when adding new group
descriptors.
mkfs.ext4 /dev/sda 3G
tune2fs -O ^resize_inode /dev/sda #forget to run requested e2fsck
mount /dev/sda /mnt
resize2fs /dev/sda 8G
The fix is simple, add a check in ext4_resize_begin() to make sure that
the es->s_reserved_gdt_blocks is zero when the resize_inode feature is
disabled.
Cc: stable@kernel.org Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220601092717.763694-1-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ding Xiang [Mon, 30 May 2022 10:00:47 +0000 (18:00 +0800)]
ext4: make variable "count" signed
Since dx_make_map() may return -EFSCORRUPTED now, so change "count" to
be a signed integer so we can correctly check for an error code returned
by dx_make_map().
Baokun Li [Sat, 28 May 2022 11:00:16 +0000 (19:00 +0800)]
ext4: correct the judgment of BUG in ext4_mb_normalize_request
ext4_mb_normalize_request() can move logical start of allocated blocks
to reduce fragmentation and better utilize preallocation. However logical
block requested as a start of allocation (ac->ac_o_ex.fe_logical) should
always be covered by allocated blocks so we should check that by
modifying and to or in the assertion.
we can easily reproduce this problem with the following commands:
`fallocate -l100M disk`
`mkfs.ext4 -b 1024 -g 256 disk`
`mount disk /mnt`
`fsstress -d /mnt -l 0 -n 1000 -p 1`
The size must be smaller than or equal to EXT4_BLOCKS_PER_GROUP.
Therefore, "start + size <= ac->ac_o_ex.fe_logical" may occur
when the size is truncated. So start should be the start position of
the group where ac_o_ex.fe_logical is located after alignment.
In addition, when the value of fe_logical or EXT4_BLOCKS_PER_GROUP
is very large, the value calculated by start_off is more accurate.
Cc: stable@kernel.org Fixes: 8d80954c43e8 ("ext4: trim allocation requests to group size") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Ritesh Harjani <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/20220528110017.354175-2-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Eric Biggers [Thu, 26 May 2022 04:04:12 +0000 (21:04 -0700)]
ext4: fix up test_dummy_encryption handling for new mount API
Since ext4 was converted to the new mount API, the test_dummy_encryption
mount option isn't being handled entirely correctly, because the needed
fscrypt_set_test_dummy_encryption() helper function combines
parsing/checking/applying into one function. That doesn't work well
with the new mount API, which split these into separate steps.
This was sort of okay anyway, due to the parsing logic that was copied
from fscrypt_set_test_dummy_encryption() into ext4_parse_param(),
combined with an additional check in ext4_check_test_dummy_encryption().
However, these overlooked the case of changing the value of
test_dummy_encryption on remount, which isn't allowed but ext4 wasn't
detecting until ext4_apply_options() when it's too late to fail.
Another bug is that if test_dummy_encryption was specified multiple
times with an argument, memory was leaked.
Fix this up properly by using the new helper functions that allow
splitting up the parse/check/apply steps for test_dummy_encryption.
projects / kernel.git / log