Simon Glass [Sun, 6 Mar 2022 03:19:01 +0000 (20:19 -0700)]
binman: Refactor fit to generate output at the end
At present the fit implementation creates the output tree while
scanning the FIT description. Then it updates the tree later when the
data is known.
This works, but is a bit confusing, since it requires mixing the scanning
code with the generation code, with a fix-up step at the end.
It is actually possible to do this in two phases, one to scan everything
and the other to generate the FIT. Thus the FIT is generated in one pass,
when everything is known.
Update the code accordingly. The only functional change is that the 'data'
property for each node are now last instead of first, which is really a
more natural position. Update the affected test to deal with this.
One wrinkle is that the calculated properties (image-pos, size and offset)
are now added before the FIT is generated. so we must filter these out
when copying properties from the binman description to the FIT.
Most of the change here is splitting out some of the code from the
ReadEntries() implementation into _BuildInput(). So despite the large
diff, most of the code is the same. It is not feasible to split this patch
up, so far as I can tell.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:00 +0000 (20:19 -0700)]
binman: Rename ExpandEntries to gen_entries
Leave the 'expand' term for use by entry types which have an expanded
version of themselves. Rename this method to indicate that it generates
subentries.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:18:59 +0000 (20:18 -0700)]
binman: Rename ExpandToLimit to extend_to_limit
The word 'expand' is used for entries which generate subentries. It is
also used for entries that can have an '_expanded' version which is used
to break out its contents.
Rather than talking about expanding an entry's size, use the term
'extending'. It is slightly more precise and avoids the above conflicts.
This change renders the old 'expand-size' property invalid, so add an
error check for that.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:18:57 +0000 (20:18 -0700)]
elf: Rename load_segments() and module failure
Rename this function to make it clear that it only reads loadable
segments. Also update the error for missing module to better match the
message emitted by Python.
Simon Glass [Sun, 6 Mar 2022 03:18:52 +0000 (20:18 -0700)]
dtoc: Make GetArgs() more flexible
At present it is not possible to have arguments which include spaces.
Update the function to only split the args if the property is a single
string. This is a bit inconsistent, but might still be useful.
Simon Glass [Mon, 28 Feb 2022 22:13:47 +0000 (15:13 -0700)]
sandbox: Open host file for read-only access if needed
Some files cannot be written but read-only access is still useful for
tests. Add a fallback to read-only access when needed.
This is useful in CI when opening a large data file provided by docker,
where read/write access would result in copying the file, thus needing
a lot of extra disk space.
Jan Kiszka [Mon, 28 Feb 2022 16:06:20 +0000 (17:06 +0100)]
binman: Include also subnodes in generator nodes
This allows to prefill fdt and config nodes with hash and signature
subnodes. It's just important to place the child nodes last so that
hashes do not come before the data - would be disliked by mkimage.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 14 Mar 2022 14:26:11 +0000 (15:26 +0100)]
arm64: zynqmp: Add pinctrl emmc description to SM-K26
Production SOM has emmc on it and make sense to describe pin description to
be able use EMMC if it is not configured via psu_init.
(Still some regs are not handled but this is one step in that direction)
Huang Jianan [Sat, 26 Feb 2022 07:05:48 +0000 (15:05 +0800)]
lib/lz4: update LZ4 decompressor module
Update the LZ4 compression module based on LZ4 v1.8.3 in order to
use the newest LZ4_decompress_safe_partial() which can now decode
exactly the nb of bytes requested.
Andre Przywara [Fri, 4 Mar 2022 16:30:08 +0000 (16:30 +0000)]
vexpress64: fvp: Fix automatic boot
Commit c258080c5ad3 ("vexpress64: Clean up BASE_FVP boot configuration")
cleaned up the usage of default address variables, but missed to update
the address for the kernel in the FVP's bootcmd definition.
Change ${kernel_addr} to read ${kernel_addr_r} to bring back the
automated boot for the fastmodel.
Also use "setenv" instead of the potentially ambiguous "set" on the way.
Fixes: c258080c5ad3 ("vexpress64: Clean up BASE_FVP boot configuration") Signed-off-by: Andre Przywara <andre.przywara@arm.com>
board: ti: j721e: evm.c: Fix the probing of in Sierra SerDes0
Initialization and power on operations of links have been moved under the
link device in the Sierra SerDes driver. Also, the UCLASS of
sierra_phy_provider has been changed to UCLASS_MISC.
Therefore, fix the probing of SerDes0 instance accordingly.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
phy: cadence: Sierra: Move the link operations from serdes phy to link device
In commit d8556b1f3cb2 ("phy: cadence: Sierra: Add a UCLASS_PHY device for
links"), a separate udevice of type UCLASS_PHY was created for each link.
Therefore, move the corresponding link operations under the link device.
Also, change the uclass of sierra phy to UCLASS_MISC as it is no longer the
phy device.
Fixes: d8556b1f3cb2 ("phy: cadence: Sierra: Add a UCLASS_PHY device for links") Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
rockchip: sdhci: Fix RK3399 eMMC PHY power cycling
The Rockchip RK3399 eMMC PHY has to be power-cycled while changing its
clock speed to some higher speeds. This is dependent on the desired
SDHCI clock speed, and it looks like the PHY should be powered off while
setting the SDHCI clock in these cases.
Commit 98a215fb58f0 ("mmc: rockchip_sdhci: add phy and clock config for
rk3399") attempts to do this in the set_ios_post() hook by setting the
SDHCI clock once more while the PHY is turned off/on as necessary, as
the SDHCI framework does not provide a way to override how it sets its
clock. However, the commit breaks reinitializing the eMMC on a few
boards including chromebook_kevin and reportedly ROCKPro64.
This patch reworks the power cycling to utilize the SDHCI framework
slightly better (using the set_control_reg() hook to power off the PHY
and set_ios_post() hook to power it back on) which happens to fix the
issue, at least on a chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Michal Simek [Mon, 7 Mar 2022 07:53:38 +0000 (08:53 +0100)]
arm64: zynqmp: Fix i2c addresses for zynqmp-p-a2197
After double checking some i2c addresses are not correct. It is visible
from i2c dump
ZynqMP> i2c bus
Bus 3: i2c@ff020000
74: i2c-mux@74, offset len 1, flags 0
Bus 5: i2c@ff020000->i2c-mux@74->i2c@0
Bus 6: i2c@ff020000->i2c-mux@74->i2c@2
Bus 7: i2c@ff020000->i2c-mux@74->i2c@1
Bus 8: i2c@ff020000->i2c-mux@74->i2c@3
Bus 4: i2c@ff030000 (active 4)
74: i2c-mux@74, offset len 1, flags 0
Bus 9: i2c@ff030000->i2c-mux@74->i2c@0
Bus 10: i2c@ff030000->i2c-mux@74->i2c@3
Bus 11: i2c@ff030000->i2c-mux@74->i2c@4
Bus 12: i2c@ff030000->i2c-mux@74->i2c@5 (active 12)
51: generic_51, offset len 1, flags 0
60: generic_60, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
Bus 13: i2c@ff030000->i2c-mux@74->i2c@6 (active 13)
51: generic_51, offset len 1, flags 0
5d: generic_5d, offset len 1, flags 0
74: generic_74, offset len 1, flags 0
ZynqMP> i2c dev 4
Setting bus to 4
ZynqMP> i2c mw 74 0 18
ZynqMP> i2c probe
Valid chip addresses: 18 36 37 50 51 60 74
ZynqMP> i2c mw 74 0 20
ZynqMP> i2c probe
Valid chip addresses: 51 60 74
where it is clear that si570 (u5) is at 0x60 address and 8t49n240 (u39) is
also at address 0x60 based on log above.
i2c address 0x74 is i2c mux and 0x51 is eeprom.
Xilinx ZynqMP SOC can set 6 parameters for its pins. pinmux status
command will print the status of these parameters for each pin. But
current print buffer length is only 40 characters long, increase it
to 80 to print all the parameters.
Michal Simek [Mon, 7 Mar 2022 15:48:17 +0000 (16:48 +0100)]
cmd: test: pinmux: Do not check all empty spaces
There is really no value to check empty spaces. That's why use
ut_assert_nextlinen() instead of ut_assert_nextline().
This change ensures that PINMUX_SIZE can be increased without changing
tests.
Pali Rohár [Mon, 7 Mar 2022 18:12:59 +0000 (19:12 +0100)]
arm: a37xx: Remap IO space to bus address 0x0
Remap PCI I/O space to the bus address 0x0 in the Armada 37xx device-tree
in order to support legacy I/O port based cards which have hardcoded I/O
ports in low address space.
Some legacy PCI I/O based cards do not support 32-bit I/O addressing.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Fix parsing of option -b with optional argument again.
Fixes: 8083af97baac ("tools: kwboot: Allow to use -b without image path as the last getopt() option") Signed-off-by: Pali Rohár <pali@kernel.org> Reported-by: Tony Dinh <mibodhi@gmail.com> Tested-by: Tony Dinh <mibodhi at gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Mar 2022 18:03:08 +0000 (19:03 +0100)]
tools: kwboot: Check if baudrate value is supported before sending image
Call kwboot_open_tty() which baudrate value which was specified at the
command line by option -B. This function returns error if baudrate is not
supported by selected tty device.
Initial baudrate for image transfer is always 115200, so call
kwboot_tty_change_baudrate() with value 115200 immediately after
kwboot_open_tty() if baudrate specified by option -B is different than
115200.
This makes kwboot fail immediately, informing that baudrate is unsupported,
instead of failing only after the first part of image is already sent.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Mon, 7 Mar 2022 18:03:07 +0000 (19:03 +0100)]
tools: kwboot: Allow to specify custom baudrate only in supported operations
Custom baudrate different than 115200 may be specified only when kwboot is
not going to send boot/debug message pattern or when it is going to send
boot message pattern with image file (in which case baudrate change happens
after sending kwbimage header). BootROM detects boot/debug message pattern
only at baudrate 115200.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
efi_loader: copy GUID in InstallProtocolInterface()
InstallProtocolInterface() is called with a pointer to the protocol GUID.
There is not guarantee that the memory used by the caller for the protocol
GUID stays allocated. To play it safe the GUID should be copied to U-Boot's
internal structures.
Reported-by: Joerie de Gram <j.de.gram@gmail.com> Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
cmd: add serial console support for the cls command
Currently the cls command does not support the serial console
The screen can be cleared in the video uclass, the colored frame buffer
console, and the serial console by sending the same escape sequence.
This reduces the cls command to a single printf() statement on most
boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Sat, 26 Feb 2022 21:17:24 +0000 (15:17 -0600)]
ARM: am3517_evm: Remove hard-coded pin muxing
With updated device trees now supporting pinmuxing for USB,
ethernet, MMC, and other peripherals necessary to start MLO
and U-Boot, the hard-coded pinmux options can be removed since
they are now handed by DM and only muxed when the respective
peripheral needs it.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
Adam Ford [Sat, 26 Feb 2022 21:17:23 +0000 (15:17 -0600)]
ARM: dts: am3517-evm: Sync DTS with Linux 5.17-rc5
Sync the am3517-evm device tree files with those from Linux
5.17-rc5 with some additional fixes for pinmuxing Ethernet and
moving the pinmux references to the respective peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
Adam Ford [Sat, 26 Feb 2022 16:49:47 +0000 (10:49 -0600)]
ARM: dts: logicpd-som-lv: Resync DTS files with Linux 5.17-rc5
Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5
with some additional pending changes to address issues with
wrong pin-muxing on the OMAP35.
configs: j721e_hs_evm_a72_defconfig: Add command for initializing QSGMII PHY
QSGMII PHY present on the j721e common processor board requires
to be initialized before the core boots up. Therefore, run the
corresponding command during boot to do the same.
include: configs: j721e_evm.h: Fix the env variable corresponding to QSGMII PHY init
QSGMII PHY initialization should only be done for J721E EVMs and not for
J721E-SK boards. Therefore, fix the environment variables accordingly.
Also, by default remote processors should not be booted in U-Boot but
rather be left to the users to enable this by setting dorprocboot.
Therefore, remove dorprocboot that is being set by default.
Fixes: 693f57b00bf2 ("include: configs: j721e_evm: Add support to boot ethfw core in j721e") Reported-by: Suman Anna <s-anna@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Romain Naour [Fri, 25 Feb 2022 11:18:34 +0000 (12:18 +0100)]
ARM: omap3_beagle: Enable DM_PMIC and DM_REGULATOR
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Romain Naour [Fri, 25 Feb 2022 11:18:33 +0000 (12:18 +0100)]
ARM: omap3_beagle: Enable Pinctrl
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Tom Rini [Thu, 10 Mar 2022 13:28:40 +0000 (08:28 -0500)]
Merge branch '2022-03-09-events-subsystem' into next
To quote the author:
It is a common need in U-Boot to have one subsystem notify another
when something happens. An example is reading a partition table when a
new block device is set up.
It is also common to add weak functions and 'hook' functions to modify
how U-Boot works. See for example ft_board_setup() and the like.
U-Boot would benefit from a generic mechanism to handle these cases,
with the ability to hook into various 'events' in a
subsystem-independent and transparent way.
This series provides a way to create and dispatch events, with a way of
registering a 'spy' which watches for events of different types. This
allows 'hook' functions to be created in a generic way.
It also includes a script to list the hooks in an image, which is a bit
easier to debug than weak functions, as well as an 'event' command to
do the same from within U-Boot.
These 'static' events can be used to replace hooks like misc_init_f(),
for example. Also included is basic support for 'dynamic' events, where
a spy can be registered at runtime. The need for this is still being
figured out.
Simon Glass [Fri, 4 Mar 2022 15:43:07 +0000 (08:43 -0700)]
event: Add a script to decode the event-spy list
For debugging and dicoverability it is useful to be able to see a list of
each event spy in a U-Boot ELF file. Add a script which shows this, along
with the event type and the source location. This makes events a little
easier to use than weak functions, for example.
Add a basic sandbox test as well. We could provide a test for other
boards, but for now, few use events.
Simon Glass [Fri, 4 Mar 2022 15:43:04 +0000 (08:43 -0700)]
event: Convert misc_init_f() to use events
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Simon Glass [Fri, 4 Mar 2022 15:43:00 +0000 (08:43 -0700)]
event: Add basic support for events
Add a way to create and dispatch events without needing to allocate
memory. Also add a way to 'spy' on events, thus allowing 'hooks' to be
created.
Use a linker list for static events, which we can use to replace functions
like arch_cpu_init_f(). Allow an EVENT_DEBUG option which makes it
easier to see what is going on at runtime, but uses more code space.
Dynamic events allow the creation of a spy at runtime. This is not always
necessary, but can be enabled with EVENT_DYNAMIC if needed.
Simon Glass [Fri, 4 Mar 2022 15:42:59 +0000 (08:42 -0700)]
binman: Expand elf support a little
Allow finding a symbol by its address. Also export the function to get
the file offset of a particular address, so it can be used by a script to
be added.
Andre Przywara [Tue, 11 Jan 2022 12:46:06 +0000 (12:46 +0000)]
sunxi: boards: Enable SPI flash support in U-Boot proper
Some sunxi boards ship with SPI flash, which allows booting through the
BootROM. We cover this functionality by a separate SPL "mini" driver.
Separately we have a proper DM_SPI driver for U-Boot proper, which
provides access to the SPI flash through the "sf" command. That allows
to update the firmware on the SPI flash, also to store the environment
there.
However only very few boards actually enable support for U-Boot proper,
even though that would work and the SPL part is configured.
Use the cleaned up configuration scheme to enable SPI flash on those
boards which mention a SPI flash in their .dts, or which use the SPL SPI
support.
Out of the box this would enable storing the environment on the SPI
flash, and allows people to read or write the flash from U-Boot, for
instance to update the SPI flash when booted via an SD card.
For this to actually work there must be a "spi0" alias in the DT, which
most boards are missing. But this should be addressed separately.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:05 +0000 (12:46 +0000)]
env: sunxi: enable ENV_IS_IN_SPI_FLASH
Now that sunxi uses CONFIG_SPI more sanely, and can also now properly
load the environment from SPI flash, let's enable the symbol that
actually considers the SPI flash when accessing the environment.
As this symbol depends on CONFIG_SPI, which we now only enable if the
board has a SPI flash, we can make if "default y" for all Allwinner
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:04 +0000 (12:46 +0000)]
sunxi: use boot source for determining environment location
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.
Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).
This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:03 +0000 (12:46 +0000)]
env: sunxi: Define location in SPI flash
To allow loading and storing the environment from SPI flash, adjust the
raw offset variables for Allwinner boards to make sense there.
U-Boot (including SPL and other blobs) is loaded from the beginning of
SPI flash, so move the environment location as far back as possible, to
not create unnecessary limits. As those offsets are shared with (now
mostly unused) raw MMC environment, we should respect the common one
megabyte limit, which also makes sense on SPI flash.
So limit the environment for those raw locations to 64KB, and place it
just below 1MB (@960KB).
Those values are currently unused, unless someone forcibly enables the
raw MMC environment. In this case it would break as of now, as the
current offset of 544KB is far too low for the current (arm64) U-Boot
proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Andre Przywara [Tue, 11 Jan 2022 12:46:02 +0000 (12:46 +0000)]
sunxi: Kconfig: Fix up SPI configuration
Commit 14619307efdd ("arm: sunxi: Enable SPI/SPI-FLASH support for A64")
selected CONFIG_SPI by default on all Allwinner A64 boards, even though
only 4 out of the 14 A64 boards have a SPI flash chip. All other SoCs
had to manually select DM_SPI and friends, even though they are a
platform property (the sunxi SPI driver is DM_SPI only).
Clean this up to allow easy selection of SPI flash support in U-Boot
proper, by selecting DM_SPI and DM_SPI_FLASH *if* CONFIG_SPI is
selected, for *all* Allwinner SoCs. This simplifies the defconfig for
two Libretech boards already.
Also remove the forced CONFIG_SPI from the A64 Kconfig, instead let the
four boards which allow SPI booting select this explicitly.
Any board wishing to support SPI flash in U-Boot proper now just defines
CONFIG_SPI and CONFIG_SPI_FLASH_<vendor> in its defconfig, Kconfig takes
care of the rest.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Michal Simek [Wed, 23 Feb 2022 14:45:42 +0000 (15:45 +0100)]
net: phy: Add support for ethernet-phy-id with gpio reset
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Sai Pavan Boddu [Tue, 1 Mar 2022 08:16:50 +0000 (09:16 +0100)]
i2c: i2c-cdns: Start read transaction after write to transfer_size reg
Avoid a race condition where read transaction is started
keeping expected bytes as 0. Which sometimes would result in sending
STOP signal as no data is expected. Observed on QEMU platform.
Michal Simek [Wed, 23 Feb 2022 14:52:03 +0000 (15:52 +0100)]
dma: xilinx: Add Display Port DMA driver
Display Port (DP) has own dma driver that's why add this skeleton driver
only for handling power domain setting and send configuration object to
PMUFW to enable it.
Michal Simek [Wed, 23 Feb 2022 14:52:02 +0000 (15:52 +0100)]
video: Add skeleton driver for ZynqMP Display port driver
The reason for this driver is to use call power management driver to enable
it in PMUFW. There is missing functionality now but should be added in
near future.
mmc: zynq_sdhci: Add support for dynamic configuration
Add support for dynamic configuration which will takes care of
configuring the SD secure space configuration registers using firmware
APIs, performing SD reset assert and deassert.
High level sequence:
- Check for the PM dynamic configuration support, if no error proceed
with SD dynamic configurations(next steps) otherwise skip the dynamic
configuration.
- Put the SD Controller in reset.
- Configure SD Fixed configurations.
- Configure the SD Slot Type.
- Configure the BASE_CLOCK.
- Configure the 8-bit support.
- Bring the SD Controller out of reset.
In the above steps, apart from the Fixed configurations, remaining all
configurations are dynamic and they will be read from devicetree.
And also remove hardcoded secure register writes, as dynamic sd config
support is added.
projects / uboot.git / log