net: dsa: microchip: lan937x: fix maximum frame length check
Maximum frame length check is enabled in lan937x switch on POR, But it
is found to be disabled on driver during port setup operation. Due to
this, packets are not dropped when transmitted with greater than configured
value. For testing, setup made for lan1->lan2 transmission and configured
lan1 interface with a frame length (less than 1500 as mentioned in
documentation) and transmitted packets with greater than configured value.
Expected no packets at lan2 end, but packets observed at lan2.
Based on the documentation, packets should get discarded if the actual
packet length doesn't match the frame length configured. Frame length check
should be disabled only for cascaded ports due to tailtags.
This feature was disabled on ksz9477 series due to ptp issue, which is
not in lan937x series. But since lan937x took ksz9477 as base, frame
length check disabled here as well. Patch added to remove this portion
from port setup so that maximum frame length check will be active for
normal ports.
Use GFP_ATOMIC when allocating pages out of the hotpath,
continue to use GFP_KERNEL when allocating pages during setup.
GFP_KERNEL will allow blocking which allows it to succeed
more often in a low memory enviornment but in the hotpath we do
not want to allow the allocation to block.
bnxt_en: fix flags to check for supported fw version
The warning message of unsupported FW appears every time RX timestamps
are disabled on the interface. The patch fixes the flags to correct set
for the check.
Fixes: 4af09912dd18 ("bnxt_en: Enable packet timestamping for all RX packets") Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20220915234932.25497-1-vfedorenko@novek.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 20 Sep 2022 01:17:22 +0000 (18:17 -0700)]
Merge tag 'wireless-2022-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.0
Late stage fixes for v6.0. Temporarily mark iwlwifi's mei code broken
as it breaks suspend for iwd users and also don't spam nss trimming
messages. mt76 has fixes for aggregation sequence numbers and a
regression related to the VHT extended NSS BW feature.
* tag 'wireless-2022-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2
wifi: mt76: fix reading current per-tid starting sequence number for aggregation
wifi: iwlwifi: Mark IWLMEI as broken
wifi: iwlwifi: don't spam logs with NSS>2 messages
====================
Jakub Kicinski [Tue, 20 Sep 2022 01:13:43 +0000 (18:13 -0700)]
Merge tag 'batadv-net-pullrequest-20220916' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- Fix hang up with small MTU hard-interface, by Shigeru Yoshida
* tag 'batadv-net-pullrequest-20220916' of git://git.open-mesh.org/linux-merge:
batman-adv: Fix hang up with small MTU hard-interface
====================
sfc: fix null pointer dereference in efx_hard_start_xmit
Trying to get the channel from the tx_queue variable here is wrong
because we can only be here if tx_queue is NULL, so we shouldn't
dereference it. As the above comment in the code says, this is very
unlikely to happen, but it's wrong anyway so let's fix it.
I hit this issue because of a different bug that caused tx_queue to be
NULL. If that happens, this is the error message that we get here:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
Fixes: d10ba6547835 ("sfc: decouple TXQ type from label") Reported-by: Tianhao Zhao <tizhao@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220914111135.21038-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sfc: fix TX channel offset when using legacy interrupts
In legacy interrupt mode the tx_channel_offset was hardcoded to 1, but
that's not correct if efx_sepparate_tx_channels is false. In that case,
the offset is 0 because the tx queues are in the single existing channel
at index 0, together with the rx queue.
Without this fix, as soon as you try to send any traffic, it tries to
get the tx queues from an uninitialized channel getting these errors:
WARNING: CPU: 1 PID: 0 at drivers/net/ethernet/sfc/tx.c:540 efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
RIP: 0010:efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
Fixes: 85316e38494a ("sfc: fix wrong tx channel offset with efx_separate_tx_channels") Reported-by: Tianhao Zhao <tizhao@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220914103648.16902-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 20 Sep 2022 01:01:04 +0000 (18:01 -0700)]
Merge tag 'for-net-2022-09-09' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix HCIGETDEVINFO regression
* tag 'for-net-2022-09-09' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: Fix HCIGETDEVINFO regression
====================
Lorenzo Bianconi [Tue, 13 Sep 2022 13:03:05 +0000 (15:03 +0200)]
net: ethernet: mtk_eth_soc: enable XDP support just for MT7986 SoC
Disable page_pool/XDP support for MT7621 SoC in order fix a regression
introduce adding XDP for MT7986 SoC. There is no a real use case for XDP
on MT7621 since it is a low-end cpu. Moreover this patch reduces the
memory footprint.
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com> Fixes: 23c4b376a76d ("net: ethernet: mtk_eth_soc: rely on page_pool for single page buffers") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/2bf31e27b888c43228b0d84dd2ef5033338269e2.1663074002.git.lorenzo@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Per GDMA spec, rmb is necessary after checking owner_bits, before
reading EQ or CQ entries.
Add rmb in these two places to comply with the specs.
Cc: stable@vger.kernel.org Fixes: 93c07632429e ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Reported-by: Sinan Kaya <Sinan.Kaya@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Link: https://lore.kernel.org/r/1662928805-15861-1-git-send-email-haiyangz@microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Thompson [Fri, 2 Sep 2022 16:42:47 +0000 (12:42 -0400)]
mlxbf_gige: clear MDIO gateway lock after read
The MDIO gateway (GW) lock in BlueField-2 GIGE logic is
set after read. This patch adds logic to make sure the
lock is always cleared at the end of each MDIO transaction.
Peilin Ye [Thu, 8 Sep 2022 23:15:23 +0000 (16:15 -0700)]
tcp: Use WARN_ON_ONCE() in tcp_read_skb()
Prevent tcp_read_skb() from flooding the syslog.
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Sep 2022 13:34:01 +0000 (14:34 +0100)]
Merge branch 'net-unsync-addresses-from-ports'
From: Benjamin Poirier <bpoirier@nvidia.com>
To: netdev@vger.kernel.org Cc: Jay Vosburgh <j.vosburgh@gmail.com>,
Veaceslav Falico <vfalico@gmail.com>,
Andy Gospodarek <andy@greyhouse.net>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Jiri Pirko <jiri@resnulli.us>, Shuah Khan <shuah@kernel.org>,
Jonathan Toppins <jtoppins@redhat.com>,
linux-kselftest@vger.kernel.org
Subject: [PATCH net v3 0/4] Unsync addresses from ports when stopping aggregated devices
Date: Wed, 7 Sep 2022 16:56:38 +0900 [thread overview]
Message-ID: <20220907075642.475236-1-bpoirier@nvidia.com> (raw)
This series fixes similar problems in the bonding and team drivers.
Because of missing dev_{uc,mc}_unsync() calls, addresses added to
underlying devices may be leftover after the aggregated device is deleted.
Add the missing calls and a few related tests.
v2:
* fix selftest installation, see patch 3
v3:
* Split lacpdu_multicast changes to their own patch, #1
* In ndo_{add,del}_slave methods, only perform address list changes when
the aggregated device is up (patches 2 & 3)
* Add selftest function related to the above change (patch 4)
====================
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The team driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former team
ports after a team device has been deleted; see test_LAG_cleanup() in the
last patch in this series.
Add unsync calls at their expected location, team_close().
v3:
* When adding or deleting a port, only sync/unsync addresses if the team
device is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: c4c5d58badd6 ("net: introduce ethernet teaming device") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netdev drivers are expected to call dev_{uc,mc}_sync() in their
ndo_set_rx_mode method and dev_{uc,mc}_unsync() in their ndo_stop method.
This is mentioned in the kerneldoc for those dev_* functions.
The bonding driver calls dev_{uc,mc}_unsync() during ndo_uninit instead of
ndo_stop. This is ineffective because address lists (dev->{uc,mc}) have
already been emptied in unregister_netdevice_many() before ndo_uninit is
called. This mistake can result in addresses being leftover on former bond
slaves after a bond has been deleted; see test_LAG_cleanup() in the last
patch in this series.
Add unsync calls, via bond_hw_addr_flush(), at their expected location,
bond_close().
Add dev_mc_add() call to bond_open() to match the above change.
v3:
* When adding or deleting a slave, only sync/unsync, add/del addresses if
the bond is up. In other cases, it is taken care of at the right time by
ndo_open/ndo_set_rx_mode/ndo_stop.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There are already a few definitions of arrays containing
MULTICAST_LACPDU_ADDR and the next patch will add one more use. These all
contain the same constant data so define one common instance for all
bonding code.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: marvell: prestera: add support for for Aldrin2
Aldrin2 (98DX8525) is a Marvell Prestera PP, with 100G support.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
V2:
- retarget to net tree instead of net-next;
- fix missed colon in patch subject ('net marvell' vs 'net: mavell'); Signed-off-by: David S. Miller <davem@davemloft.net>
net/ieee802154: fix uninit value bug in dgram_sendmsg
There is uninit value bug in dgram_sendmsg function in
net/ieee802154/socket.c when the length of valid data pointed by the
msg->msg_name isn't verified.
We introducing a helper function ieee802154_sockaddr_check_size to
check namelen. First we check there is addr_type in ieee802154_addr_sa.
Then, we check namelen according to addr_type.
Also fixed in raw_bind, dgram_bind, dgram_connect.
Signed-off-by: Haimin Zhang <tcs_kernel@tencent.com> Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 1a392e16fcf3 ("mptcp: drop SK_RECLAIM_* macros"),
if rmem_fwd_alloc become negative, mptcp_rmem_uncharge() can
try to reclaim a negative amount of pages, since the expression:
reclaimable >= PAGE_SIZE
will evaluate to true for any negative value of the int
'reclaimable': 'PAGE_SIZE' is an unsigned long and
the negative integer will be promoted to a (very large)
unsigned long value.
Still after the mentioned commit, kfree_skb_partial()
in mptcp_try_coalesce() will reclaim most of just released fwd
memory, so that following charging of the skb delta size will
lead to negative fwd memory values.
At that point a racing recvmsg() can trigger the splat.
Address the issue switching the order of the memory accounting
operations. The fwd memory can still transiently reach negative
values, but that will happen in an atomic scope and no code
path could touch/use such value.
Reported-by: kernel test robot <oliver.sang@intel.com> Fixes: 1a392e16fcf3 ("mptcp: drop SK_RECLAIM_* macros") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20220906180404.1255873-1-matthieu.baerts@tessares.net Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: phy: aquantia: wait for the suspend/resume operations to finish
The Aquantia datasheet notes that after issuing a Processor-Intensive
MDIO operation, like changing the low-power state of the device, the
driver should wait for the operation to finish before issuing a new MDIO
command.
The new aqr107_wait_processor_intensive_op() function is added which can
be used after these kind of MDIO operations. At the moment, we are only
adding it at the end of the suspend/resume calls.
The issue was identified on a board featuring the AQR113C PHY, on
which commands like 'ip link (..) up / down' issued without any delays
between them would render the link on the PHY to remain down.
The issue was easy to reproduce with a one-liner:
$ ip link set dev ethX down; ip link set dev ethX up; \
ip link set dev ethX down; ip link set dev ethX up;
Fixes: 001bdceb0565 ("net: phy: aquantia: add suspend / resume callbacks for AQR107 family") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220906130451.1483448-1-ioana.ciornei@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Felix Fietkau [Wed, 7 Sep 2022 09:52:28 +0000 (11:52 +0200)]
wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2
Some users have reported being unable to connect to MT76x0 APs running mt76
after a commit enabling the VHT extneded NSS BW feature.
Fix this regression by ensuring that this feature only gets enabled on drivers
that support it
Cc: stable@vger.kernel.org Fixes: 49c64e99e389 ("mt76: enable the VHT extended NSS BW feature") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220907095228.82072-1-nbd@nbd.name
Felix Fietkau [Fri, 26 Aug 2022 18:23:29 +0000 (20:23 +0200)]
wifi: mt76: fix reading current per-tid starting sequence number for aggregation
The code was accidentally shifting register values down by tid % 32 instead of
(tid * field_size) % 32.
Cc: stable@vger.kernel.org Fixes: 42532277ad1d ("mt76: mt7615: re-enable offloading of sequence number assignment") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220826182329.18155-1-nbd@nbd.name
The iwlmei driver breaks iwlwifi when returning from suspend. The interface
ends up in the 'down' state after coming back from suspend. And iwd doesn't
touch the interface state, but wpa_supplicant does, so the bug only happens on
iwd.
The bug report[0] has been open for four months now, and no fix seems to be
forthcoming. Since just disabling the iwlmei driver works as a workaround,
let's mark the config option as broken until it can be fixed properly.
Recent changes breaks HCIGETDEVINFO since it changes the size of
hci_dev_info.
Fixes: 1cbf406bf653 ("Bluetooth: Add initial implementation of CIS connections") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
__flow_hash_consistentify() wrongly swaps ipv4 addresses in few cases.
This function is indirectly used by __skb_get_hash_symmetric(), which is
used to fanout packets in AF_PACKET.
Intrusion detection systems may be impacted by this issue.
__flow_hash_consistentify() computes the addresses difference then swaps
them if the difference is negative. In few cases src - dst and dst - src
are both negative.
The following snippet mimics __flow_hash_consistentify():
In the first case the addresses differences are always < 0, therefore
__flow_hash_consistentify() always swaps, thus dst->src and src->dst
packets have differents hashes.
Fixes: 56c7592b4aadd ("net: Add full IPv6 addresses to flow_keys") Signed-off-by: Ludovic Cintrat <ludovic.cintrat@gatewatcher.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lu Wei [Wed, 7 Sep 2022 10:12:04 +0000 (18:12 +0800)]
ipvlan: Fix out-of-bound bugs caused by unset skb->mac_header
If an AF_PACKET socket is used to send packets through ipvlan and the
default xmit function of the AF_PACKET socket is changed from
dev_queue_xmit() to packet_direct_xmit() via setsockopt() with the option
name of PACKET_QDISC_BYPASS, the skb->mac_header may not be reset and
remains as the initial value of 65535, this may trigger slab-out-of-bounds
bugs as following:
=================================================================
UG: KASAN: slab-out-of-bounds in ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
PU: 2 PID: 1768 Comm: raw_send Kdump: loaded Not tainted 6.0.0-rc4+ #6
ardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33
all Trace:
print_address_description.constprop.0+0x1d/0x160
print_report.cold+0x4f/0x112
kasan_report+0xa3/0x130
ipvlan_xmit_mode_l2+0xdb/0x330 [ipvlan]
ipvlan_start_xmit+0x29/0xa0 [ipvlan]
__dev_direct_xmit+0x2e2/0x380
packet_direct_xmit+0x22/0x60
packet_snd+0x7c9/0xc40
sock_sendmsg+0x9a/0xa0
__sys_sendto+0x18a/0x230
__x64_sys_sendto+0x74/0x90
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause is:
1. packet_snd() only reset skb->mac_header when sock->type is SOCK_RAW
and skb->protocol is not specified as in packet_parse_headers()
2. packet_direct_xmit() doesn't reset skb->mac_header as dev_queue_xmit()
In this case, skb->mac_header is 65535 when ipvlan_xmit_mode_l2() is
called. So when ipvlan_xmit_mode_l2() gets mac header with eth_hdr() which
use "skb->head + skb->mac_header", out-of-bound access occurs.
This patch replaces eth_hdr() with skb_eth_hdr() in ipvlan_xmit_mode_l2()
and reset mac header in multicast to solve this out-of-bound bug.
Fixes: 35b69229bc37 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Lu Wei <luwei32@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following set contains four netfilter patches for your *net* tree.
When there are multiple Contact headers in a SIP message its possible
the next headers won't be found because the SIP helper confuses relative
and absolute offsets in the message. From Igor Ryzhov.
Make the nft_concat_range self-test support socat, this makes the
selftest pass on my test VM, from myself.
nf_conntrack_irc helper can be tricked into opening a local port forward
that the client never requested by embedding a DCC message in a PING
request sent to the client. Fix from David Leadbeater.
Both have been broken since the kernel 2.6.x days.
The 'osf' match might indicate success while it could not find
anything, broken since 5.2 . Fix from Pablo Neira.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
iavf: Fix cached head and tail value for iavf_get_tx_pending
The underlying hardware may or may not allow reading of the head or tail
registers and it really makes no difference if we use the software
cached values. So, always used the software cached values.
Fixes: 97e675c0012c ("i40e: Detection and recovery of TX queue hung logic moved to service_task from tx_timeout") Signed-off-by: Brett Creeley <brett.creeley@intel.com> Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously changing mac address gives false negative because
ip link set <interface> address <MAC> return with
RTNLINK: Permission denied.
In iavf_set_mac was check if PF handled our mac set request,
even before filter was added to list.
Because this check returns always true and it never waits for
PF's response.
Move iavf_is_mac_handled to wait_event_interruptible_timeout
instead of false. Now it will wait for PF's response and then
check if address was added or rejected.
Fixes: 6fb54b1682cb ("iavf: Add waiting for response from PF in set mac") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Co-developed-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ding Hui [Wed, 17 Aug 2022 10:53:18 +0000 (18:53 +0800)]
ice: Fix crash by keep old cfg when update TCs more than queues
There are problems if allocated queues less than Traffic Classes.
Commit 77d548751ead ("ice: ethtool: Prohibit improper channel config
for DCB") already disallow setting less queues than TCs.
Another case is if we first set less queues, and later update more TCs
config due to LLDP, ice_vsi_cfg_tc() will failed but left dirty
num_txq/rxq and tc_cfg in vsi, that will cause invalid pointer access.
Dave Ertman [Tue, 9 Aug 2022 17:24:23 +0000 (10:24 -0700)]
ice: Don't double unplug aux on peer initiated reset
In the IDC callback that is accessed when the aux drivers request a reset,
the function to unplug the aux devices is called. This function is also
called in the ice_prepare_for_reset function. This double call is causing
a "scheduling while atomic" BUG.
The correct place to unplug the aux devices for a reset is in the
prepare_for_reset function, as this is a common place for all reset flows.
It also has built in protection from being called twice in a single reset
instance before the aux devices are replugged.
Fixes: dfd6ba335c7ff ("ice: Register auxiliary device to provide RDMA") Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Helena Anna Dubel <helena.anna.dubel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
- dsa: microchip: fix kernel oops on ksz8 switches
- dsa: qca8k: fix NULL pointer dereference for
of_device_get_match_data
Previous releases - regressions:
- netfilter: clean up hook list when offload flags check fails
- wifi: mt76: fix crash in chip reset fail
- rxrpc: fix ICMP/ICMP6 error handling
- ice: fix DMA mappings leak
- i40e: fix kernel crash during module removal
Previous releases - always broken:
- ipv6: sr: fix out-of-bounds read when setting HMAC data.
- tcp: TX zerocopy should not sense pfmemalloc status
- sch_sfb: don't assume the skb is still around after
enqueueing to child
- netfilter: drop dst references before setting
- wifi: wilc1000: fix DMA on stack objects
- rxrpc: fix an insufficiently large sglist in
rxkad_verify_packet_2()
- fec: use a spinlock to guard `fep->ptp_clk_on`
Misc:
- usb: qmi_wwan: add Quectel RM520N"
* tag 'net-6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (50 commits)
sch_sfb: Also store skb len before calling child enqueue
net: phy: lan87xx: change interrupt src of link_up to comm_ready
net/smc: Fix possible access to freed memory in link clear
net: ethernet: mtk_eth_soc: check max allowed hash in mtk_ppe_check_skb
net: skb: export skb drop reaons to user by TRACE_DEFINE_ENUM
net: ethernet: mtk_eth_soc: fix typo in __mtk_foe_entry_clear
net: dsa: felix: access QSYS_TAG_CONFIG under tas_lock in vsc9959_sched_speed_set
net: dsa: felix: disable cut-through forwarding for frames oversized for tc-taprio
net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet
net: usb: qmi_wwan: add Quectel RM520N
net: dsa: qca8k: fix NULL pointer dereference for of_device_get_match_data
tcp: fix early ETIMEDOUT after spurious non-SACK RTO
stmmac: intel: Simplify intel_eth_pci_remove()
net: mvpp2: debugfs: fix memory leak when using debugfs_lookup()
ipv6: sr: fix out-of-bounds read when setting HMAC data.
bonding: accept unsolicited NA message
bonding: add all node mcast address when slave up
bonding: use unspecified address if no available link local address
wifi: use struct_group to copy addresses
wifi: mac80211_hwsim: check length for virtio packets
...
Linus Torvalds [Wed, 31 Aug 2022 16:46:12 +0000 (09:46 -0700)]
fs: only do a memory barrier for the first set_buffer_uptodate()
Commit a8d654978b92 ("add barriers to buffer_uptodate and
set_buffer_uptodate") added proper memory barriers to the buffer head
BH_Uptodate bit, so that anybody who tests a buffer for being up-to-date
will be guaranteed to actually see initialized state.
However, that commit didn't _just_ add the memory barrier, it also ended
up dropping the "was it already set" logic that the BUFFER_FNS() macro
had.
That's conceptually the right thing for a generic "this is a memory
barrier" operation, but in the case of the buffer contents, we really
only care about the memory barrier for the _first_ time we set the bit,
in that the only memory ordering protection we need is to avoid anybody
seeing uninitialized memory contents.
Any other access ordering wouldn't be about the BH_Uptodate bit anyway,
and would require some other proper lock (typically BH_Lock or the folio
lock). A reader that races with somebody invalidating the buffer head
isn't an issue wrt the memory ordering, it's a serialization issue.
Now, you'd think that the buffer head operations don't matter in this
day and age (and I certainly thought so), but apparently some loads
still end up being heavy users of buffer heads. In particular, the
kernel test robot reported that not having this bit access optimization
in place caused a noticeable direct IO performance regression on ext4:
sch_sfb: Also store skb len before calling child enqueue
Cong Wang noticed that the previous fix for sch_sfb accessing the queued
skb after enqueueing it to a child qdisc was incomplete: the SFB enqueue
function was also calling qdisc_qstats_backlog_inc() after enqueue, which
reads the pkt len from the skb cb field. Fix this by also storing the skb
len, and using the stored value to increment the backlog after enqueueing.
Fixes: 2ef1492a6e0b ("sch_sfb: Don't assume the skb is still around after enqueueing to child") Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Acked-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20220905192137.965549-1-toke@toke.dk Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: phy: lan87xx: change interrupt src of link_up to comm_ready
Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.
Hyunwoo Kim [Wed, 7 Sep 2022 16:07:14 +0000 (09:07 -0700)]
efi: capsule-loader: Fix use-after-free in efi_capsule_write
A race condition may occur if the user calls close() on another thread
during a write() operation on the device node of the efi capsule.
This is a race condition that occurs between the efi_capsule_write() and
efi_capsule_flush() functions of efi_capsule_fops, which ultimately
results in UAF.
So, the page freeing process is modified to be done in
efi_capsule_release() instead of efi_capsule_flush().
Yacan Liu [Tue, 6 Sep 2022 13:01:39 +0000 (21:01 +0800)]
net/smc: Fix possible access to freed memory in link clear
After modifying the QP to the Error state, all RX WR would be completed
with WC in IB_WC_WR_FLUSH_ERR status. Current implementation does not
wait for it is done, but destroy the QP and free the link group directly.
So there is a risk that accessing the freed memory in tasklet context.
Fixes: 8df89c64cd63 ("smc: initialize IB transport incl. PD, MR, QP, CQ, event, WR") Signed-off-by: Yacan Liu <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: mtk_eth_soc: check max allowed hash in mtk_ppe_check_skb
Even if max hash configured in hw in mtk_ppe_hash_entry is
MTK_PPE_ENTRIES - 1, check theoretical OOB accesses in
mtk_ppe_check_skb routine
Fixes: 40d09f3927421 ("net: ethernet: mtk_eth_soc: rework hardware flow table management") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: skb: export skb drop reaons to user by TRACE_DEFINE_ENUM
As Eric reported, the 'reason' field is not presented when trace the
kfree_skb event by perf:
$ perf record -e skb:kfree_skb -a sleep 10
$ perf script
ip_defrag 14605 [021] 221.614303: skb:kfree_skb:
skbaddr=0xffff9d2851242700 protocol=34525 location=0xffffffffa39346b1
reason:
The cause seems to be passing kernel address directly to TP_printk(),
which is not right. As the enum 'skb_drop_reason' is not exported to
user space through TRACE_DEFINE_ENUM(), perf can't get the drop reason
string from the 'reason' field, which is a number.
Therefore, we introduce the macro DEFINE_DROP_REASON(), which is used
to define the trace enum by TRACE_DEFINE_ENUM(). With the help of
DEFINE_DROP_REASON(), now we can remove the auto-generate that we
introduced in the commit 7a870caffe6f
("net: skb: use auto-generation to convert skb drop reason to string"),
and define the string array 'drop_reasons'.
Hmmmm...now we come back to the situation that have to maintain drop
reasons in both enum skb_drop_reason and DEFINE_DROP_REASON. But they
are both in dropreason.h, which makes it easier.
After this commit, now the format of kfree_skb is like this:
net: ethernet: mtk_eth_soc: fix typo in __mtk_foe_entry_clear
Set ib1 state to MTK_FOE_STATE_UNBIND in __mtk_foe_entry_clear routine.
Fixes: 2aa931cdbe4af ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nfnetlink_osf: fix possible bogus match in nf_osf_find()
nf_osf_find() incorrectly returns true on mismatch, this leads to
copying uninitialized memory area in nft_osf which can be used to leak
stale kernel stack data to userspace.
Fixes: 32660bfd7e29 ("netfilter: nft_osf: Add version option support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de>
David Leadbeater [Fri, 26 Aug 2022 04:56:57 +0000 (14:56 +1000)]
netfilter: nf_conntrack_irc: Tighten matching on DCC message
CTCP messages should only be at the start of an IRC message, not
anywhere within it.
While the helper only decodes packes in the ORIGINAL direction, its
possible to make a client send a CTCP message back by empedding one into
a PING request. As-is, thats enough to make the helper believe that it
saw a CTCP message.
ct_sip_next_header and ct_sip_get_header return an absolute
value of matchoff, not a shift from current dataoff.
So dataoff should be assigned matchoff, not incremented by it.
This issue can be seen in the scenario when there are multiple
Contact headers and the first one is using a hostname and other headers
use IP addresses. In this case, ct_sip_walk_headers will work as follows:
The first ct_sip_get_header call to will find the first Contact header
but will return -1 as the header uses a hostname. But matchoff will
be changed to the offset of this header. After that, dataoff should be
set to matchoff, so that the next ct_sip_get_header call find the next
Contact header. But instead of assigning dataoff to matchoff, it is
incremented by it, which is not correct, as matchoff is an absolute
value of the offset. So on the next call to the ct_sip_get_header,
dataoff will be incorrect, and the next Contact header may not be
found at all.
David S. Miller [Wed, 7 Sep 2022 12:44:04 +0000 (13:44 +0100)]
Merge branch 'dsa-felix-fixes'
Vladimir Oltean says:
====================
Fixes for Felix DSA driver calculation of tc-taprio guard bands
This series fixes some bugs which are not quite new, but date from v5.13
when static guard bands were enabled by Michael Walle to prevent
tc-taprio overruns.
The investigation started when Xiaoliang asked privately what is the
expected max SDU for a traffic class when its minimum gate interval is
10 us. The answer, as it turns out, is not an L1 size of 1250 octets,
but 1245 octets, since otherwise, the switch will not consider frames
for egress scheduling, because the static guard band is exactly as large
as the time interval. The switch needs a minimum of 33 ns outside of the
guard band to consider a frame for scheduling, and the reduction of the
max SDU by 5 provides exactly for that.
The fix for that (patch 1/3) is relatively small, but during testing, it
became apparent that cut-through forwarding prevents oversized frame
dropping from working properly. This is solved through the larger patch
2/3. Finally, patch 3/3 fixes one more tc-taprio locking problem found
through code inspection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 5 Sep 2022 17:01:25 +0000 (20:01 +0300)]
net: dsa: felix: access QSYS_TAG_CONFIG under tas_lock in vsc9959_sched_speed_set
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set()
runs unlocked with respect to the other functions that access it, which
are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and
vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock,
so move the vsc9959_sched_speed_set() access under that lock as well, to
resolve the concurrency.
Fixes: b4a408349587 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 5 Sep 2022 17:01:24 +0000 (20:01 +0300)]
net: dsa: felix: disable cut-through forwarding for frames oversized for tc-taprio
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605,
frames even way larger than 601 octets are transmitted even though these
should be considered as oversized, according to the documentation, and
dropped.
Since oversized frame dropping depends on frame size, which is only
known at the EOF stage, and therefore not at SOF when cut-through
forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_*
into consideration for traffic classes that are cut-through.
Since cut-through forwarding has no UAPI to control it, and the driver
enables it based on the mantra "if we can, then why not", the strategy
is to alter vsc9959_cut_through_fwd() to take into consideration which
tc's have oversize frame dropping enabled, and disable cut-through for
them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the
cut-through determination process.
There are 2 strategies for vsc9959_cut_through_fwd() to determine
whether a tc has oversized dropping enabled or not. One is to keep a bit
mask of traffic classes per port, and the other is to read back from the
hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the
feature is enabled). We choose reading back from registers, because
struct ocelot_port is shared with drivers (ocelot, seville) that don't
support either cut-through nor tc-taprio, and we don't have a felix
specific extension of struct ocelot_port. Furthermore, reading registers
from the Felix hardware is quite cheap, since they are memory-mapped.
Fixes: b4a408349587 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard
band added earlier than its 'gate close' event, such that packet
overruns won't occur in the worst case of the largest packet possible.
Since guard bands are statically determined based on the per-tc
QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU,
we need to discuss what happens with TC 7 depending on kernel version,
since the driver, prior to commit b4a408349587 ("net: dsa: felix: drop
oversized frames with tc-taprio instead of hanging the port"), did not
touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU.
1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to
1518, and at gigabit this introduces a static guard band (independent
of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit
time of 20 octets => 160 ns). But this is larger than the time window
itself, of 10000 ns. So, the queue system never considers a frame with
TC 7 as eligible for transmission, since the gate practically never
opens, and these frames are forever stuck in the TX queues and hang
the port.
2 (after vsc9959_tas_guard_bands_update): Under the sole goal of
enabling oversized frame dropping, we make an effort to set
QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays
one more role, which we did not take into account: per-tc static guard
band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead).
There is a discrepancy between what the driver thinks (that there is
no guard band, and 100% of min_gate_len[tc] is available for egress
scheduling) and what the hardware actually does (crops the equivalent
of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this
means that the hardware thinks it has exactly 0 ns for scheduling tc 7.
In both cases, even minimum sized Ethernet frames are stuck on egress
rather than being considered for scheduling on TC 7, even if they would
fit given a proper configuration. Considering the current situation,
with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230
octets in size are not eligible for oversized dropping (because they are
smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible
for scheduling either, because the min_gate_len[7] (10000 ns) minus the
guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per
octet == 9840 ns) minus the guard band auto-added for L1 overhead by
QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets)
leaves 0 ns for scheduling in the queue system proper.
Investigating the hardware behavior, it becomes apparent that the queue
system needs precisely 33 ns of 'gate open' time in order to consider a
frame as eligible for scheduling to a tc. So the solution to this
problem is to amend vsc9959_tas_guard_bands_update(), by giving the
per-tc guard bands less space by exactly 33 ns, just enough for one
frame to be scheduled in that interval. This allows the queue system to
make forward progress for that port-tc, and prevents it from hanging.
Fixes: 31ddbf30ae7e ("net: dsa: felix: re-enable TAS guard band mode") Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at the code, this seems to be related to a hardware limitation,
and there's nothing to be done. In an effort to keep my dmesg
manageable, downgrade this error to "debug" rather than "info".
David Howells [Tue, 6 Sep 2022 21:09:11 +0000 (22:09 +0100)]
afs: Return -EAGAIN, not -EREMOTEIO, when a file already locked
When trying to get a file lock on an AFS file, the server may return
UAEAGAIN to indicate that the lock is already held. This is currently
translated by the default path to -EREMOTEIO.
Translate it instead to -EAGAIN so that we know we can retry it.
Merge tag 'erofs-for-6.0-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
- Fix return codes in erofs_fscache_{meta_,}read_folio error paths
- Fix potential wrong pcluster sizes for later non-4K lclusters
- Fix in-memory pcluster use-after-free on UP platforms
* tag 'erofs-for-6.0-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix pcluster use-after-free on UP platforms
erofs: avoid the potentially wrong m_plen for big pcluster
erofs: fix error return code in erofs_fscache_{meta_,}read_folio
net: dsa: qca8k: fix NULL pointer dereference for of_device_get_match_data
of_device_get_match_data is called on priv->dev before priv->dev is
actually set. Move of_device_get_match_data after priv->dev is correctly
set to fix this kernel panic.
Fixes: b6c4612af70b ("net: dsa: qca8k: cache match data to speed up access") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220904215319.13070-1-ansuelsmth@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
tcp: fix early ETIMEDOUT after spurious non-SACK RTO
Fix a bug reported and analyzed by Nagaraj Arankal, where the handling
of a spurious non-SACK RTO could cause a connection to fail to clear
retrans_stamp, causing a later RTO to very prematurely time out the
connection with ETIMEDOUT.
Here is the buggy scenario, expanding upon Nagaraj Arankal's excellent
report:
(*1) Send one data packet on a non-SACK connection
(*2) Because no ACK packet is received, the packet is retransmitted
and we enter CA_Loss; but this retransmission is spurious.
(*3) The ACK for the original data is received. The transmitted packet
is acknowledged. The TCP timestamp is before the retrans_stamp,
so tcp_may_undo() returns true, and tcp_try_undo_loss() returns
true without changing state to Open (because tcp_is_sack() is
false), and tcp_process_loss() returns without calling
tcp_try_undo_recovery(). Normally after undoing a CA_Loss
episode, tcp_fastretrans_alert() would see that the connection
has returned to CA_Open and fall through and call
tcp_try_to_open(), which would set retrans_stamp to 0. However,
for non-SACK connections we hold the connection in CA_Loss, so do
not fall through to call tcp_try_to_open() and do not set
retrans_stamp to 0. So retrans_stamp is (erroneously) still
non-zero.
At this point the first "retransmission event" has passed and
been recovered from. Any future retransmission is a completely
new "event". However, retrans_stamp is erroneously still
set. (And we are still in CA_Loss, which is correct.)
(*4) After 16 minutes (to correspond with tcp_retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and
(*4) and we disabled keep alives.
The socket's timeout SHOULD be calculated from this point in
time, but instead it's calculated from the prior "event" 16
minutes ago (step (*2)).
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT, prematurely, because retrans_stamp is (erroneously)
too far in the past (set at the time of (*2)).
This commit fixes this bug by ensuring that we reuse in
tcp_try_undo_loss() the same careful logic for non-SACK connections
that we have in tcp_try_undo_recovery(). To avoid duplicating logic,
we factor out that logic into a new
tcp_is_non_sack_preventing_reopen() helper and call that helper from
both undo functions.
Merge tag 'soc-fixes-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are the expected fixes for the SoC tree. I have let the patches
pile up a little too long, so this is bigger than I would have liked.
- Minor build fixes for Broadcom STB and NXP i.MX8M SoCs as well\ as
TEE firmware
- Updates to the MAINTAINERS file for the PolarFire SoC
- Minor DT fixes for Renesas White Hawk and Arm Versatile and Juno
platforms
- A fix for a missing dependnecy in the NXP DPIO driver
- Broadcom BCA fixes to the newly added devicetree files
- Multiple fixes for Microchip AT91 based SoCs, dealing with
self-refresh timings and regulator settings in DT
- Several DT fixes for NXP i.MX platforms, dealing with incorrect
GPIO settings, extraneous nodes, and a wrong clock setting"
* tag 'soc-fixes-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (45 commits)
soc: fsl: select FSL_GUTS driver for DPIO
ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time
ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time
ARM: dts: at91: sama7g5ek: specify proper regulator output ranges
ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges
ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges
ARM: at91: pm: fix DDR recalibration when resuming from backup and self-refresh
ARM: at91: pm: fix self-refresh for sama7g5
soc: brcmstb: pm-arm: Fix refcount leak and __iomem leak bugs
ARM: configs: at91: remove CONFIG_MICROCHIP_PIT64B
ARM: ixp4xx: fix typos in comments
arm64: dts: renesas: r8a779g0: Fix HSCIF0 interrupt number
tee: fix compiler warning in tee_shm_register()
arm64: dts: freescale: verdin-imx8mp: fix atmel_mxt_ts reset polarity
arm64: dts: freescale: verdin-imx8mm: fix atmel_mxt_ts reset polarity
arm64: dts: imx8mp: Fix I2C5 GPIO assignment on i.MX8M Plus DHCOM
arm64: dts: imx8mm-venice-gw7901: fix port/phy validation
arm64: dts: verdin-imx8mm: add otg2 pd to usbphy
soc: imx: gpcv2: Assert reset before ungating clock
arm64: dts: ls1028a-qds-65bb: don't use in-band autoneg for 2500base-x
...
erofs: fix pcluster use-after-free on UP platforms
During stress testing with CONFIG_SMP disabled, KASAN reports as below:
==================================================================
BUG: KASAN: use-after-free in __mutex_lock+0xe5/0xc30
Read of size 8 at addr ffff8881094223f8 by task stress/7789
CPU: 0 PID: 7789 Comm: stress Not tainted 6.0.0-rc1-00002-g0d53d2e882f9 #3
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Call Trace:
<TASK>
..
__mutex_lock+0xe5/0xc30
..
z_erofs_do_read_page+0x8ce/0x1560
..
z_erofs_readahead+0x31c/0x580
..
Freed by task 7787
kasan_save_stack+0x1e/0x40
kasan_set_track+0x20/0x30
kasan_set_free_info+0x20/0x40
__kasan_slab_free+0x10c/0x190
kmem_cache_free+0xed/0x380
rcu_core+0x3d5/0xc90
__do_softirq+0x12d/0x389
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0x97/0xb0
call_rcu+0x3d/0x3f0
erofs_shrink_workstation+0x11f/0x210
erofs_shrink_scan+0xdc/0x170
shrink_slab.constprop.0+0x296/0x530
drop_slab+0x1c/0x70
drop_caches_sysctl_handler+0x70/0x80
proc_sys_call_handler+0x20a/0x2f0
vfs_write+0x555/0x6c0
ksys_write+0xbe/0x160
do_syscall_64+0x3b/0x90
The root cause is that erofs_workgroup_unfreeze() doesn't reset to
orig_val thus it causes a race that the pcluster reuses unexpectedly
before freeing.
Since UP platforms are quite rare now, such path becomes unnecessary.
Let's drop such specific-designed path directly instead.
Yue Hu [Fri, 12 Aug 2022 06:01:50 +0000 (14:01 +0800)]
erofs: avoid the potentially wrong m_plen for big pcluster
Actually, 'compressedlcs' stores compressed block count rather than
lcluster count. Therefore, the number of bits for shifting the count
should be 'LOG_BLOCK_SIZE' rather than 'lclusterbits' although current
lcluster size is 4K.
The value of 'm_plen' will be wrong once we enable the non 4K-sized
lcluster.
There is no point to call pcim_iounmap_regions() in the remove function,
this frees a managed resource that would be release by the framework
anyway.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mvpp2: debugfs: fix memory leak when using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. Fix this up to be much
simpler logic and only create the root debugfs directory once when the
driver is first accessed. That resolves the memory leak and makes
things more obvious as to what the intent is.
Cc: Marcin Wojtas <mw@semihalf.com> Cc: Russell King <linux@armlinux.org.uk> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Cc: stable <stable@kernel.org> Fixes: 39d7629f2ab8 ("net: mvpp2: add a debugfs interface for the Header Parser") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Fri, 2 Sep 2022 09:45:06 +0000 (10:45 +0100)]
ipv6: sr: fix out-of-bounds read when setting HMAC data.
The SRv6 layer allows defining HMAC data that can later be used to sign IPv6
Segment Routing Headers. This configuration is realised via netlink through
four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and
SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual
length of the SECRET attribute, it is possible to provide invalid combinations
(e.g., secret = "", secretlen = 64). This case is not checked in the code and
with an appropriately crafted netlink message, an out-of-bounds read of up
to 64 bytes (max secret length) can occur past the skb end pointer and into
skb_shared_info:
Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
208 memcpy(hinfo->secret, secret, slen);
(gdb) bt
#0 seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
#1 0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600,
extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>,
family=<optimized out>) at net/netlink/genetlink.c:731
#2 0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00,
family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775
#3 genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792
#4 0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>)
at net/netlink/af_netlink.c:2501
#5 0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803
#6 0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000)
at net/netlink/af_netlink.c:1319
#7 netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>)
at net/netlink/af_netlink.c:1345
#8 0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921
...
(gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end
$1 = 0xffff88800b1b76c0
(gdb) p/x secret
$2 = 0xffff88800b1b76c0
(gdb) p slen
$3 = 64 '@'
The OOB data can then be read back from userspace by dumping HMAC state. This
commit fixes this by ensuring SECRETLEN cannot exceed the actual length of
SECRET.
Reported-by: Lucas Leong <wmliang.tw@gmail.com>
Tested: verified that EINVAL is correctly returned when secretlen > len(secret) Fixes: 6a8afd2321551 ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 30 Aug 2022 09:37:22 +0000 (17:37 +0800)]
bonding: accept unsolicited NA message
The unsolicited NA message with all-nodes multicast dest address should
be valid, as this also means the link could reach the target.
Also rename bond_validate_ns() to bond_validate_na().
Reported-by: LiLiang <liali@redhat.com> Fixes: 880632c7e38e ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 30 Aug 2022 09:37:21 +0000 (17:37 +0800)]
bonding: add all node mcast address when slave up
When a link is enslave to bond, it need to set the interface down first.
This makes the slave remove mac multicast address 33:33:00:00:00:01(The
IPv6 multicast address ff02::1 is kept even when the interface down). When
bond set the slave up, ipv6_mc_up() was not called due to commit bc43c5cd188c
("bonding / ipv6: no addrconf for slaves separately from master").
This is not an issue before we adding the lladdr target feature for bonding,
as the mac multicast address will be added back when bond interface up and
join group ff02::1.
But after adding lladdr target feature for bonding. When user set a lladdr
target, the unsolicited NA message with all-nodes multicast dest will be
dropped as the slave interface never add 33:33:00:00:00:01 back.
Fix this by calling ipv6_mc_up() to add 33:33:00:00:00:01 back when
the slave interface up.
Reported-by: LiLiang <liali@redhat.com> Fixes: 880632c7e38e ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 30 Aug 2022 09:37:20 +0000 (17:37 +0800)]
bonding: use unspecified address if no available link local address
When ns_ip6_target was set, the ipv6_dev_get_saddr() will be called to get
available source address and send IPv6 neighbor solicit message.
If the target is global address, ipv6_dev_get_saddr() will get any
available src address. But if the target is link local address,
ipv6_dev_get_saddr() will only get available address from our interface,
i.e. the corresponding bond interface.
But before bond interface up, all the address is tentative, while
ipv6_dev_get_saddr() will ignore tentative address. This makes we can't
find available link local src address, then bond_ns_send() will not be
called and no NS message was sent. Finally bond interface will keep in
down state.
Fix this by sending NS with unspecified address if there is no available
source address.
Reported-by: LiLiang <liali@redhat.com> Fixes: 880632c7e38e ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix handling of PCI domains in /proc on 32-bit systems using the
recently added support for numbering buses from zero for each domain.
- A fix and a revert for some changes to use READ/WRITE_ONCE() which
caused problems with KASAN enabled due to sanitisation calls being
introduced in low-level paths that can't cope with it.
- Fix build errors on 32-bit caused by the syscall table being
misaligned sometimes.
- Two fixes to get IBM Cell native machines booting again, which had
bit-rotted while my QS22 was temporarily out of action.
- Fix the papr_scm driver to not assume the order of events returned by
the hypervisor is stable, and a related compile fix.
Thanks to Aneesh Kumar K.V, Christophe Leroy, Jordan Niethe, Kajol Jain,
Masahiro Yamada, Nathan Chancellor, Pali Rohár, Vaibhav Jain, and Zhouyi
Zhou.
* tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
Revert "powerpc/irq: Don't open code irq_soft_mask helpers"
powerpc: Fix hard_irq_disable() with sanitizer
powerpc/rtas: Fix RTAS MSR[HV] handling for Cell
Revert "powerpc: Remove unused FW_FEATURE_NATIVE references"
powerpc: align syscall table for ppc32
powerpc/pci: Enable PCI domains in /proc when PCI bus numbers are not unique
powerpc/papr_scm: Fix nvdimm event mappings
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"s390:
- PCI interpretation compile fixes
RISC-V:
- fix unused variable warnings in vcpu_timer.c
- move extern sbi_ext declarations to a header
x86:
- check validity of argument to KVM_SET_MP_STATE
- use guest's global_ctrl to completely disable guest PEBS
- fix a memory leak on memory allocation failure
- mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
- fix build failure with Clang integrated assembler
- fix MSR interception
- always flush TLBs when enabling dirty logging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check validity of argument to KVM_SET_MP_STATE
perf/x86/core: Completely disable guest PEBS via guest's global_ctrl
KVM: x86: fix memoryleak in kvm_arch_vcpu_create()
KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
KVM: s390: pci: Hook to access KVM lowlevel from VFIO
riscv: kvm: move extern sbi_ext declarations to a header
riscv: kvm: vcpu_timer: fix unused variable warnings
KVM: selftests: Fix ambiguous mov in KVM_ASM_SAFE()
KVM: selftests: Fix KVM_EXCEPTION_MAGIC build with Clang
KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
kvm: x86: mmu: Always flush TLBs when enabling dirty logging
kvm: x86: mmu: Drop the need_remote_flush() function
Makefile.extrawarn: re-enable -Wformat for clang; take 2
-Wformat was recently re-enabled for builds with clang, then quickly
re-disabled, due to concerns stemming from the frequency of default
argument promotion related warning instances.
commit e4c420f97dd0 ("Makefile.extrawarn: re-enable -Wformat for clang")
commit e7c0bfd5eb05 ("Revert "Makefile.extrawarn: re-enable -Wformat for clang"")
ISO WG14 has ratified N2562 to address default argument promotion
explicitly for printf, as part of the upcoming ISO C2X standard.
The behavior of clang was changed in clang-16 to not warn for the cited
cases in all language modes.
Add a version check, so that users of clang-16 now get the full effect
of -Wformat. For older clang versions, re-enable flags under the
-Wformat group that way users still get some useful checks related to
format strings, without noisy default argument promotion warnings. I
intentionally omitted -Wformat-y2k and -Wformat-security from being
re-enabled, which are also part of -Wformat in clang-16.
David S. Miller [Sun, 4 Sep 2022 10:23:11 +0000 (11:23 +0100)]
Merge tag 'wireless-2022-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes berg says:
====================
We have a handful of fixes:
- fix DMA from stack in wilc1000 driver
- fix crash on chip reset failure in mt7921e
- fix for the reported warning on aggregation timer expiry
- check packet lengths in hwsim virtio paths
- fix compiler warnings/errors with AAD construction by
using struct_group
- fix Intel 4965 driver rate scale operation
- release channel contexts correctly in mac80211 mlme code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A a set of fixes from the GPIO subsystem.
Most are small driver fixes except the realtek-otto driver patch which
is pretty big but addresses a significant flaw that can cause the CPU
to stay infinitely busy on uncleared ISR on some platforms.
Summary:
- MAINTAINERS update
- fix resource leaks in gpio-mockup and gpio-pxa
- add missing locking in gpio-pca953x
- use 32-bit I/O in gpio-realtek-otto
- make irq_chip structures immutable in four more drivers"
* tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ws16c48: Make irq_chip immutable
gpio: 104-idio-16: Make irq_chip immutable
gpio: 104-idi-48: Make irq_chip immutable
gpio: 104-dio-48e: Make irq_chip immutable
gpio: realtek-otto: switch to 32-bit I/O
gpio: pca953x: Add mutex_lock for regcache sync in PM
gpio: mockup: remove gpio debugfs when remove device
gpio: pxa: use devres for the clock struct
MAINTAINERS: rectify entry for XILINX GPIO DRIVER
Merge tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a minor fix for the Xen grant driver
- a small series fixing a recently introduced problem in the Xen
blkfront/blkback drivers with negotiation of feature usage
* tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
xen-blkfront: Cache feature_persistent value before advertisement
xen-blkfront: Advertise feature-persistent as user requested
xen-blkback: Advertise feature-persistent as user requested
Merge tag 'loongarch-fixes-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors or warnings, cleanup some code, and adjust
arch_do_signal_or_restart() to adapt generic entry"
* tag 'loongarch-fixes-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: mm: Remove the unneeded result variable
LoongArch: Fix arch_remove_memory() undefined build error
LoongArch: Fix section mismatch due to acpi_os_ioremap()
LoongArch: Improve dump_tlb() output messages
LoongArch: Adjust arch_do_signal_or_restart() to adapt generic entry
LoongArch: Avoid orphan input sections
Merge tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
* tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add support for Boeder Force Feedback Wheel
Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
Input: goodix - add compatible string for GT1158
MAINTAINERS: add include/dt-bindings/input to INPUT DRIVERS
Input: rk805-pwrkey - fix module autoloading
Input: goodix - add support for GT1158
dt-bindings: input: touchscreen: add compatible string for Goodix GT1158
Merge tag 'tty-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial/vt driver fixes for 6.0-rc4 that
resolve a number of reported issues:
- n_gsm fixups for previous changes that caused problems
- much-reported serdev crash fix that showed up in 6.0-rc1
- vt font selection bugfix
- kerneldoc build warning fixes
- other tiny serial core fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: n_gsm: avoid call of sleeping functions from atomic context
tty: n_gsm: replace kicktimer with delayed_work
tty: n_gsm: initialize more members at gsm_alloc_mux()
tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
tty: serial: atmel: Preserve previous USART mode if RS485 disabled
tty: serial: lpuart: disable flow control while waiting for the transmit engine to complete
tty: Fix lookahead_buf crash with serdev
serial: fsl_lpuart: RS485 RTS polariy is inverse
vt: Clear selection before changing the font
serial: document start_rx member at struct uart_ops
Merge tag 'staging-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three small staging driver fixes for 6.0-rc4 that resolve
some reported problems and add some a device id:
- new device id for r8188eu driver
- use-after-free bugfixes for the rtl8712 driver
- fix up firmware dependency problem for the r8188eu driver
All of these have been in linux-next for a while with no reported
problems"
* tag 'staging-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix use after free bugs
staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
staging: r8188eu: add firmware dependency
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's a collection of primarily clk driver fixes, with a couple fixes
to the core framework.
We had to revert out a commit that affected boot on some devices that
have the CLK_OPS_PARENT_ENABLE flag set. It isn't critical to have
that fix so we'll try again next time.
Driver side fixes include:
- Plug an OF-node refcount bug in the TI clk driver
- Fix the error handling in the raspberry pi firmware get_rate so
that errors don't look like valid frequencies
- Avoid going out of bounds in the raspberry pi driver too if the
video firmware returns something we're not expecting"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
clk: bcm: rpi: Show clock id limit in error case
clk: bcm: rpi: Add missing newline
clk: bcm: rpi: Prevent out-of-bounds access
clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
clk: core: Fix runtime PM sequence in clk_core_unprepare()
clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
clk: ti: Fix missing of_node_get() ti_find_clock_provider()
Merge tag 'hwmon-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix out of bounds access in gpio-fan driver
- Fix VOUT margin caching in PMBus core
- Avoid error message after -EPROBE_DEFER from devm_regulator_register()
* tag 'hwmon-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Fix array out of bounds access
hwmon: (pmbus) Fix vout margin caching
hwmon: (pmbus) Use dev_err_probe() to filter -EPROBE_DEFER error messages
Steven Price [Fri, 2 Sep 2022 11:26:12 +0000 (12:26 +0100)]
mm: pagewalk: Fix race between unmap and page walker
The mmap lock protects the page walker from changes to the page tables
during the walk. However a read lock is insufficient to protect those
areas which don't have a VMA as munmap() detaches the VMAs before
downgrading to a read lock and actually tearing down PTEs/page tables.
For users of walk_page_range() the solution is to simply call pte_hole()
immediately without checking the actual page tables when a VMA is not
present. We now never call __walk_page_range() without a valid vma.
For walk_page_range_novma() the locking requirements are tightened to
require the mmap write lock to be taken, and then walking the pgd
directly with 'no_vma' set.
This in turn means that all page walkers either have a valid vma, or
it's that special 'novma' case for page table debugging. As a result,
all the odd '(!walk->vma && !walk->no_vma)' tests can be removed.
Fixes: 5dcd5782f466 ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Steven Price <steven.price@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 29 Aug 2022 09:46:38 +0000 (11:46 +0200)]
wifi: use struct_group to copy addresses
We sometimes copy all the addresses from the 802.11 header
for the AAD, which may cause complaints from fortify checks.
Use struct_group() to avoid the compiler warnings/errors.
Change-Id: Ic3ea389105e7813b22095b295079eecdabde5045 Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: mac80211_hwsim: check length for virtio packets
An invalid packet with a length shorter than the specified length in the
netlink header can lead to use-after-frees and slab-out-of-bounds in the
processing of the netlink attributes, such as the following:
BUG: KASAN: slab-out-of-bounds in __nla_validate_parse+0x1258/0x2010
Read of size 2 at addr ffff88800ac7952c by task kworker/0:1/12
Johannes Berg [Fri, 2 Sep 2022 14:11:14 +0000 (16:11 +0200)]
wifi: mac80211: fix locking in auth/assoc timeout
If we hit an authentication or association timeout, we only
release the chanctx for the deflink, and the other link(s)
are released later by ieee80211_vif_set_links(), but we're
not locking this correctly.
Fix the locking here while releasing the channels and links.
Change-Id: I9e08c1a5434592bdc75253c1abfa6c788f9f39b1 Fixes: 8020ebb801e6 ("wifi: mac80211: support MLO authentication/association with one link") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
projects / kernel.git / log