This patch series includes some additional changes to the bcm_sf2 in
order to support the Device Tree firmwares provided on such platforms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Disallow port 5 to be a DSA CPU port
While the switch driver is written such that port 5 or 8 could be CPU
ports, the use case on Broadcom STB chips is to use port 8 exclusively.
The platform firmware does make port 5 comply to a proper DSA CPU port
binding by specifiying an "ethernet" phandle. This is undesirable for
now until we have an user-space configuration mechanism (such as
devlink) which could support dynamically changing the port flavor at
run time.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
octeontx2: Add support for VLAN based flow distribution
This series add support for VLAN based flow distribution for octeontx2
netdev driver. This adds support for configuring the same via ethtool.
Following tests have been done.
- Multi VLAN flow with same SD
- Multi VLAN flow with same SDFN
- Single VLAN flow with multi SD
- Single VLAN flow with multi SDFN
All tests done for udp/tcp both v4 and v6
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
George Cherian [Tue, 22 Sep 2020 13:07:27 +0000 (18:37 +0530)]
octeontx2-pf: Support to change VLAN based RSS hash options via ethtool
Add support to control rx-flow-hash based on VLAN.
By default VLAN plus 4-tuple based hashing is enabled.
Changes can be done runtime using ethtool
To enable 2-tuple plus VLAN based flow distribution
# ethtool -N <intf> rx-flow-hash <prot> sdv
To enable 4-tuple plus VLAN based flow distribution
# ethtool -N <intf> rx-flow-hash <prot> sdfnv
Signed-off-by: George Cherian <george.cherian@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
George Cherian [Tue, 22 Sep 2020 13:07:26 +0000 (18:37 +0530)]
octeontx2-af: Add support for VLAN based RSS hashing
Added support for PF/VF drivers to choose RSS flow key algorithm
with VLAN tag included in hashing input data. Only CTAG is considered.
Signed-off-by: George Cherian <george.cherian@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
kernel-doc expects the function prototype to be just after
the kernel-doc markup, as otherwise it will get it all wrong:
./net/core/dev.c:10036: warning: Excess function parameter 'dev' description in 'WAIT_REFS_MIN_MSECS'
Fixes: 0e4be9e57e8c ("net: use exponential backoff in netdev_wait_allrefs") Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Reviewed-by: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Marko [Tue, 22 Sep 2020 10:16:32 +0000 (12:16 +0200)]
net: mdio-ipq4019: add Clause 45 support
While up-streaming the IPQ4019 driver it was thought that the controller had no Clause 45 support,
but it actually does and its activated by writing a bit to the mode register.
So lets add it as newer SoC-s use the same controller and Clause 45 compliant PHY-s.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Marko [Tue, 22 Sep 2020 10:16:31 +0000 (12:16 +0200)]
net: mdio-ipq4019: change defines to upper case
In the commit adding the IPQ4019 MDIO driver, defines for timeout and sleep partially used lower case.
Lets change it to upper case in line with the rest of driver defines.
Signed-off-by: Robert Marko <robert.marko@sartura.hr> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Introduce mbox tracepoints for Octeontx2
This patchset adds tracepoints support for mailbox.
In Octeontx2, PFs and VFs need to communicate with AF
for allocating and freeing resources. Once all the
configuration is done by AF for a PF/VF then packet I/O
can happen on PF/VF queues. When an interface
is brought up many mailbox messages are sent
to AF for initializing queues. Say a VF is brought up
then each message is sent to PF and PF forwards to
AF and response also traverses from AF to PF and then VF.
To aid debugging, tracepoints are added at places where
messages are allocated, sent and message interrupts.
Below is the trace of one of the messages from VF to AF
and AF response back to VF:
~ # echo 1 > /sys/kernel/tracing/events/rvu/enable
~ # ifconfig eth20 up
[ 279.379559] eth20 NIC Link is UP 10000 Mbps Full duplex
~ # cat /sys/kernel/tracing/trace
ifconfig-171 [000] .... 275.753345: otx2_msg_alloc: [0002:02:00.1] msg:(0x400) size:40
ifconfig-171 [000] ...1 275.753347: otx2_msg_send: [0002:02:00.1] sent 1 msg(s) of size:48
v3 changes:
Removed EXPORT_TRACEPOINT_SYMBOLS of otx2_msg_send and otx2_msg_check
since they are called locally only
v2 changes:
Removed otx2_msg_err tracepoint since it is similar to devlink_hwerr
and it will be used instead when devlink supported is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With tracepoints support present in the mailbox
code this patch adds tracepoints in PF and VF drivers
at places where mailbox messages are allocated,
sent and at message interrupts.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added tracepoints in mailbox code so that
the mailbox operations like message allocation,
sending message and message interrupts are traced.
Also the mailbox errors occurred like timeout
or wrong responses are traced.
These will help in debugging mailbox issues.
Here's an example output showing one of the mailbox
messages sent by PF to AF and AF responding to it:
~# mount -t tracefs none /sys/kernel/tracing/
~# echo 1 > /sys/kernel/tracing/events/rvu/enable
~# ifconfig eth0 up
~# cat /sys/kernel/tracing/trace
kworker/u49:0-1165 [000] ...1 756.162051: otx2_msg_send: [0002:01:00.0] sent 1 msg(s) of size:32
kworker/u49:0-1165 [000] d.h. 756.162056: otx2_msg_interrupt: [0002:02:00.0] mbox interrupt AF to PF (0x1)
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Barry Song [Tue, 22 Sep 2020 01:56:15 +0000 (13:56 +1200)]
net: allwinner: remove redundant irqsave and irqrestore in hardIRQ
The comment "holders of db->lock must always block IRQs" and related
code to do irqsave and irqrestore don't make sense since we are in a
IRQ-disabled hardIRQ context.
Cc: Maxime Ripard <mripard@kernel.org> Cc: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Barry Song <song.bao.hua@hisilicon.com> Acked-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
A number of static variables were not modified. Make them const to allow
the compiler to put them in read-only memory. In order to do so,
constify a couple of input pointers as well as some local pointers.
This moves about 35Kb to read-only memory as seen by the output of the
size command.
Before:
text data bss dec hex filename
404938 111534 640 517112 7e3f8 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko
After:
text data bss dec hex filename
439499 76974 640 517113 7e3f9 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge.ko
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second part of the IGMPv3/MLDv2 support which adds support
for the fast-path. In order to be able to handle source entries we add
mdb support for S,G entries (i.e. we add source address support to
br_ip), that requires to extend the current mdb netlink API, fortunately
we just add another attribute which will contain nested future mdb
attributes, then we use it to add support for S,G user- add, del and
dump. The lookup sequence is simple: when IGMPv3/MLDv2 are enabled do
the S,G lookup first and if it fails fallback to *,G. The more complex
part is when we begin handling source lists and auto-installing S,G entries
and *,G filter mode transitions. We have the following cases:
1) *,G INCLUDE -> EXCLUDE transition: we need to install the port in
all of *,G's installed S,G entries for proper replication (except
the ones explicitly blocked), this is also necessary when adding a
new *,G EXCLUDE port group
2) *,G EXCLUDE -> INCLUDE transition: we need to remove the port from
all of *,G's installed S,G entries, this is also necessary when
removing a *,G port group
3) New S,G port entry: we need to install all current *,G EXCLUDE ports
4) Remove S,G port entry: if all other port groups were auto-installed we
can safely remove them and delete the whole S,G entry
Currently we compute these operations from the available ports, their
source lists and their filter mode. In the future we can extend the port
group structure and reduce the running time of these ops. Also one
current limitation is that host-joined S,G entries are not supported.
I.e. one cannot add "dev bridge port bridge" mdb S,G entries. The host
join is currently considered an EXCLUDE {} join, so it's reflected in
all of *,G's installed S,G entries. If an S,G,port entry is added as
temporary then the kernel can take it over if a source shows up from a
report, permanent entries are skipped. In order to properly handle
blocked sources we add a new port group blocked flag to avoid forwarding
to that port group in the S,G. Finally when forwarding we use the port
group filter mode (if it's INCLUDE and the port group is from a *,G then
don't replicate to it, respectively if it's EXCLUDE then forward) and the
blocked flag (obviously if it's set - skip that port unless it's a
router port) to decide if the port should be skipped. Another limitation
is that we can't do some of the above transitions without small traffic
drop while installing/removing entries. That will be taken care of when
we add atomic swap of port replication lists later.
Patch break down:
patches 1-3: prepare the mdb code for better extack support which is
used in future patches to return a more meaningful error
patches 4-6: add the source address field to struct br_ip, and do minor
cleanups around it
patches 7-8: extend the mdb netlink API so we can send new mdb
attributes and uses the new API for S,G entry add/del/dump
support
patch 9: takes care of S,G entries when doing a lookup (first S,G
then *,G lookup)
patch 10: adds a new port group field and attribute for origin protocol
we use the already available RTPROT_ definitions,
currently user-space entries are added as RTPROT_STATIC and
kernel entries are added as RTPROT_KERNEL, we may allow
user-space to set custom values later (e.g. for FRR, clag)
patch 11: adds an internal S,G,port rhashtable to speed up filter
mode transitions
patch 12: initial automatic install of S,G entries based on port
groups' source lists
patch 13: handles port group modes on transitions or when new
port group entries are added
patch 14: self-explanatory - adds support for blocked port group
entries needed to stop forwarding to particular S,G,port
entries
patch 15: handles host-join/leave state changes, treats host-joins
as EXCLUDE {} groups (reflected in all *,G's S,G entries)
patch 16: finally adds the fast-path filter mode and block flag
support
Here're the sets that will come next (in order):
- iproute2 support for IGMPv3/MLDv2
- selftests for all mode transitions and group flags
- explicit host tracking for proper fast-leave support
- atomic port replication lists (these are also needed for broadcast
forwarding optimizations)
- mode transition optimization and removal of open-coded sorted lists
Not implemented yet:
- Host IGMPv3/MLDv2 filter support (currently we handle only join/leave
as before)
- Proper other querier source timer and value updates
- IGMPv3/v2 MLDv2/v1 compat (I have a few rough patches for this one)
v2: fix build with CONFIG_BATMAN_ADV_MCAST in patch 6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since host joins are considered as EXCLUDE {} joins we need to reflect
that in all of *,G ports' S,G entries. Since the S,Gs can have
host_joined == true only set automatically we can safely set it to false
when removing all automatically added entries upon S,G delete.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: add support for blocked port groups
When excluding S,G entries we need a way to block a particular S,G,port.
The new port group flag is managed based on the source's timer as per
RFCs 3376 and 3810. When a source expires and its port group is in
EXCLUDE mode, it will be blocked.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: handle port group filter modes
We need to handle group filter mode transitions and initial state.
To change a port group's INCLUDE -> EXCLUDE mode (or when we have added
a new port group in EXCLUDE mode) we need to add that port to all of
*,G ports' S,G entries for proper replication. When the EXCLUDE state is
changed from IGMPv3 report, br_multicast_fwd_filter_exclude() must be
called after the source list processing because the assumption is that
all of the group's S,G entries will be created before transitioning to
EXCLUDE mode, i.e. most importantly its blocked entries will already be
added so it will not get automatically added to them.
The transition EXCLUDE -> INCLUDE happens only when a port group timer
expires, it requires us to remove that port from all of *,G ports' S,G
entries where it was automatically added previously.
Finally when we are adding a new S,G entry we must add all of *,G's
EXCLUDE ports to it.
In order to distinguish automatically added *,G EXCLUDE ports we have a
new port group flag - MDB_PG_FLAGS_STAR_EXCL.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: install S,G entries automatically based on reports
This patch adds support for automatic install of S,G mdb entries based
on the port group's source list and the source entry's timer.
Once installed the S,G will be used when forwarding packets if the
approprate multicast/mld versions are set. A new source flag called
BR_SGRP_F_INSTALLED denotes if the source has a forwarding mdb entry
installed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To speedup S,G forward handling we need to be able to quickly find out
if a port is a member of an S,G group. To do that add a global S,G port
rhashtable with key: source addr, group addr, protocol, vid (all br_ip
fields) and port pointer.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: add rt_protocol field to the port group struct
We need to be able to differentiate between pg entries created by
user-space and the kernel when we start generating S,G entries for
IGMPv3/MLDv2's fast path. User-space entries are created by default as
RTPROT_STATIC and the kernel entries are RTPROT_KERNEL. Later we can
allow user-space to provide the entry rt_protocol so we can
differentiate between who added the entries specifically (e.g. clag,
admin, frr etc).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mdb: add support for add/del/dump of entries with source
Add new mdb attributes (MDBE_ATTR_SOURCE for setting,
MDBA_MDB_EATTR_SOURCE for dumping) to allow add/del and dump of mdb
entries with a source address (S,G). New S,G entries are created with
filter mode of MCAST_INCLUDE. The same attributes are used for IPv4 and
IPv6, they're validated and parsed based on their protocol.
S,G host joined entries which are added by user are not allowed yet.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mdb: add support to extend add/del commands
Since the MDB add/del code expects an exact struct br_mdb_entry we can't
really add any extensions, thus add a new nested attribute at the level of
MDBA_SET_ENTRY called MDBA_SET_ENTRY_ATTRS which will be used to pass
all new options via netlink attributes. This patch doesn't change
anything functionally since the new attribute is not used yet, only
parsed.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: rename br_ip's u member to dst
Since now we have src in br_ip, u no longer makes sense so rename
it to dst. No functional changes.
v2: fix build with CONFIG_BATMAN_ADV_MCAST
CC: Marek Lindner <mareklindner@neomailbox.ch> CC: Simon Wunderlich <sw@simonwunderlich.de> CC: Antonio Quartulli <a@unstable.cc> CC: Sven Eckelmann <sven@narfation.org> CC: b.a.t.m.a.n@lists.open-mesh.org Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mcast: use br_ip's src for src groups and querier address
Now that we have src and dst in br_ip it is logical to use the src field
for the cases where we need to work with a source address such as
querier source address and group source address.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mdb: move all port and bridge checks to br_mdb_add
To avoid doing duplicate device checks and searches (the same were done
in br_mdb_add and __br_mdb_add) pass the already found port to __br_mdb_add
and pull the bridge's netif_running and enabled multicast checks to
br_mdb_add. This would also simplify the future extack errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/realtek/8139cp.c: In function cp_tx_timeout:
drivers/net/ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
`rc` is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Olsa [Wed, 23 Sep 2020 18:57:34 +0000 (20:57 +0200)]
bpf: Check CONFIG_BPF option for resolve_btfids
Currently all the resolve_btfids 'users' are under CONFIG_BPF
code, so if we have CONFIG_BPF disabled, resolve_btfids will
fail, because there's no data to resolve.
Disabling resolve_btfids if there's CONFIG_BPF disabled,
so we won't fail such builds.
this is a pull request of 20 patches for net-next.
The complete series target the flexcan driver and is created by Joakim
Zhang and me.
The first six patches are cleanup (sort include files alphabetically,
remove stray empty line, get rid of long lines) and adding more
registers and documentation (registers and wakeup interrupt).
Then in two patches the transceiver regulator is made optional, and a
check for maximum transceiver bitrate is added.
Then the ECC support for HW thats supports this is added.
The next three patches improve suspend and low power mode handling.
Followed by six patches that add CAN-FD support and CAN-FD related
features.
The last two patches add support for the flexcan IP core on the imx8qm
and lx2160ar1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
please apply the following patch series for qeth to netdev's net-next tree.
This brings all sorts of cleanups. Highlights are more code sharing in
the init/teardown paths, and more fine-grained rollback on errors during
initialization (instead of a full-blown teardown).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify which discipline-specific steps are needed to roll back after
error in qeth_l?_set_online(), and which are common to roll back
from qeth_hardsetup_card().
Some steps (cancelling the RX modeset, draining the TX queues) are only
necessary if the netdev was potentially UP before, so move them to the
common qeth_set_offline().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Originators of cmd IO typically hold the rtnl or conf_mutex to protect
against a concurrent teardown.
Since qeth_set_offline() already holds the conf_mutex, the main reason
why we still care about cancelling pending cmds is so that they release
the rtnl when we need it ourselves.
So move this step a little earlier into the teardown sequence.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The programming of ucast IPs via qeth_l3_modify_ip() is driven
independently from any of our typical locking mechanisms (eg. detaching
the netdevice, or holding the conf_mutex).
So when we inspect the card state to check whether the required cmd IO
should be deferred, there is no protection against concurrent state
changes.
But by slightly re-ordering the teardown sequence, we can rely on the
ip_lock to sufficiently serialize things:
1. when running concurrently to qeth_l3_set_online(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_recover_ip() will observe the state as CARD_STATE_SOFTSETUP
and not defer the IO.
2. when running concurrently to qeth_l3_set_offline(), any instance of
qeth_l3_modify_ip() that aquires the ip_lock _after_
qeth_l3_clear_ip_htable() will observe the state as CARD_STATE_DOWN
and defer the IO.
These guarantees in mind, we can now drop the conf_mutex from the
qeth_l3_modify_rxip_vipa() wrapper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the remaining occurences in sysfs code to kstrtouint().
While at it move some input parsing out of locked sections, replace an
open-coded clamp() and remove some unnecessary run-time checks for
ipatoe->mask_bits that are already enforced when creating the object.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
card->ipato is currently protected by the conf_mutex. But most users
also hold the ip_lock - in particular qeth_l3_add_ip().
So slightly expand the sections under ip_lock in a few places (to
effectively cover a few error & no-op cases), and then drop the
conf_mutex where it's no longer needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arrays with designated initializers have an implicit length of the highest
initialized value plus one. I used this to ensure that newly added entries
in enum bpf_reg_type get a NULL entry in compatible_reg_types.
This is difficult to understand since it requires knowledge of the
peculiarities of designated initializers. Use __BPF_ARG_TYPE_MAX to size
the array instead.
net: microchip: Make `lan743x_pm_suspend` function return right value
drivers/net/ethernet/microchip/lan743x_main.c: In function lan743x_pm_suspend:
`ret` is set but not used. In fact, `pci_prepare_to_sleep` function value should
be the right value of `lan743x_pm_suspend` function, therefore, fix it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 23 Sep 2020 00:44:59 +0000 (17:44 -0700)]
Merge tag 'mlx5-updates-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-09-21
Multi packet TX descriptor support for SKBs.
This series introduces some refactoring of the regular TX data path in
mlx5 and adds the Enhanced TX MPWQE feature support. MPWQE stands for
multi-packet work queue element, and it can serve multiple packets,
reducing the PCI bandwidth spent on control traffic. It should improve
performance in scenarios where PCI is the bottleneck, and xmit_more is
signaled by the kernel. The refactoring done in this series also
improves the packet rate on its own.
MPWQE is already implemented in the XDP tx path, this series adds the
support of MPWQE for regular kernel SKB tx path.
MPWQE is supported from ConnectX-5 and onward, for legacy devices we need
to keep backward compatibility for regular (Single packet) WQE descriptor.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE per SKB.
Prior to the final patch "net/mlx5e: Enhanced TX MPWQE for SKBs" that adds
the actual support, Maxim did some refactoring to the tx data path to
split it into stages and smaller helper functions that can be utilized and
reused for both legacy and new MPWQE feature.
Performance testing:
UDP performance is improved in a single stream pktgen test:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 434 -> 329
Cycles per packet: 158 -> 123
Instructions per cycle: 2.75 -> 2.67
TCP and XDP_TX single stream tests show no performance difference.
MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
MPWQE can also reduce CPU load, increasing the packet rate in case of
CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
====================
devlink: Use nla_policy to validate range
This two small patches uses nla_policy to validate user specified
fields are in valid range or not.
Patch summary:
Patch-1 checks the range of eswitch mode field
Patch-2 checks for the port type field. It eliminates a check in
code by using nla policy infrastructure.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"No common topic, just assorted fixes"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fuse: fix the ->direct_IO() treatment of iov_iter
fs: fix cast in fsparam_u32hex() macro
vboxsf: Fix the check for the old binary mount-arguments struct
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
Merge tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes - most of them regression fixes from this cycle, but also
a few stable heading fixes, and a build fix for the included demo tool
since some systems now actually have gettid() available"
* tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
io_uring: fix openat/openat2 unified prep handling
io_uring: mark statx/files_update/epoll_ctl as non-SQPOLL
tools/io_uring: fix compile breakage
io_uring: don't use retry based buffered reads for non-async bdev
io_uring: don't re-setup vecs/iter in io_resumit_prep() is already there
io_uring: don't run task work on an exiting task
io_uring: drop 'ctx' ref on task work cancelation
io_uring: grab any needed state during defer prep
Merge tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
Merge tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Check kprobe is enabled before unregistering from ftrace as it isn't
registered when disabled.
- Remove kprobes enabled via command-line that is on init text when
freed.
- Add missing RCU synchronization for ftrace trampoline symbols removed
from kallsyms.
- Free trampoline on error path if ftrace_startup() fails.
- Give more space for the longer PID numbers in trace output.
- Fix a possible double free in the histogram code.
- A couple of fixes that were discovered by sparse.
* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: init: make xbc_namebuf static
kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
tracing: fix double free
ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
tracing: Make the space reserved for the pid wider
ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
ftrace: Free the trampoline when ftrace_startup() fails
kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()
can: flexcan: add Transceiver Delay Compensation support
The CAN-FD protocol allows the transmission and reception of data at a
higher bit rate than the nominal rate used in the arbitration phase when
the message's BRS bit is set.
The TDC mechanism is effective only during the data phase of FD frames
having BRS bit set. It has no effect either on non-FD frames, or on FD
frames transmitted at normal bit rate.
ISO CAN FD is introduced to increase the failture detection capability
than non-ISO CAN FD. The non-ISO CAN FD is still supported by FlexCAN so
that it can be used mainly during an intermediate phase, for evaluation
and development purposes.
Therefore, it is strongly recommended to configure FlexCAN to the ISO
CAN FD protocol by setting the ISOCANFDEN field in the CTRL2 register.
NOTE: If you only set "fd on", driver will use ISO FD mode by default.
You should set "fd-non-iso on" after setting "fd on" if you want to use
NON ISO FD mode.
This patch adds CAN-FD mode support to the driver, it means that
payload size can extend up to 64 bytes.
Bit timing always set in the CBT register, not in the CTRL1 register any
more. This has an extend range of all CAN bit timing variables (PRESDIV,
PROPSEG, PSEG1, PSEG2 and RJW), which will improve the bit timing
accuracy.
can: flexcan: flexcan_set_bittiming(): move setup of CAN-2.0 bitiming into separate function
This is a patch prepares for the CAN-FD support. In a later patch the
setup for canfd bittiming will be added, with this patch the change is
easier to read.
Joakim Zhang [Wed, 4 Dec 2019 11:36:19 +0000 (11:36 +0000)]
can: flexcan: add LPSR mode support
On the i.MX7D in LPSR mode, the controller will be powered off and the
configuration state is lost after system resume. Upcoming i.MX8QM/QXP
will also completely power off the domain, the controller state is lost
and needs restore, too. So we need to set the pinctrl state again and
re-start chip to re-configuration after resume.
For the wakeup case, it should not set pinctrl to sleep state by
pinctrl_pm_select_sleep_state.
If the interface is down before suspend, we don't need to re-configure
it as it will be configured if the interface is brought up later.
can: flexcan: flexcan_chip_stop(): add error handling and propagate error value
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
can: flexcan: add correctable errors correction when HW supports ECC
commit cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
From above commit by Stefan Agner, the patch just disables
non-correctable errors interrupt and freeze mode. It still can correct
the correctable errors since ECC enabled by default after reset (MECR[ECCDIS]=0,
enable memory error correct) if HW supports ECC.
commit 5e269324db5a ("can: flexcan: disable completely the ECC mechanism")
From above commit by Joakim Zhang, the patch disables ECC completely (assert
MECR[ECCDIS]) according to the explanation of FLEXCAN_QUIRK_DISABLE_MECR that
disable memory error detection. This cause correctable errors cannot be
corrected even HW supports ECC.
The error correction mechanism ensures that in this 13-bit word, errors
in one bit can be corrected (correctable errors) and errors in two bits can
be detected but not corrected (non-correctable errors). Errors in more than
two bits may not be detected.
If HW supports ECC, we can use this to correct the correctable errors detected
from FlexCAN memory. Then disable non-correctable errors interrupt and freeze
mode to avoid that put FlexCAN in freeze mode.
This patch adds correctable errors correction when HW supports ECC, and
modify explanation for FLEXCAN_QUIRK_DISABLE_MECR.
can: flexcan: flexcan_probe(): make regulator xceiver optional
As the transcevier regulator is optional, this patch switches from
devm_regulator_get() to devm_regulator_get_optional(). This gets rid of "using
dummy regulator" warning message from the regulator core, if no regulator is
available.
Joakim Zhang [Wed, 4 Dec 2019 11:36:08 +0000 (11:36 +0000)]
can: flexcan: Ack wakeup interrupt separately
As FLEXCAN_ESR_ALL_INT is for all bus errors and state change IRQ
sources, strictly speaking FLEXCAN_ESR_WAK_INT does not belong to these.
So add wakeup interrupt ack separately to existing ack of the
interrupts.
This commit adds support for Enhanced TX MPWQE feature in the regular
(SKB) data path. A MPWQE (multi-packet work queue element) can serve
multiple packets, reducing the PCI bandwidth on control traffic.
Two new stats (tx*_mpwqe_blks and tx*_mpwqe_pkts) are added. The feature
is on by default and controlled by the skb_tx_mpwqe private flag.
In a MPWQE, eseg is shared among all packets, so eseg-based offloads
(IPSEC, GENEVE, checksum) run on a separate eseg that is compared to the
eseg of the current MPWQE session to decide if the new packet can be
added to the same session.
MPWQE is not compatible with certain offloads and features, such as TLS
offload, TSO, nonlinear SKBs. If such incompatible features are in use,
the driver gracefully falls back to non-MPWQE.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
UDP pktgen, 64-byte packets, single stream, MPWQE off:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 17.01 Mpps (±0.20 Mpps)
Instructions per packet: 421 -> 429
Cycles per packet: 156 -> 161
Instructions per cycle: 2.70 -> 2.67
UDP pktgen, 64-byte packets, single stream, MPWQE on:
Packet rate: 16.96 Mpps (±0.12 Mpps) -> 20.94 Mpps (±0.33 Mpps)
Instructions per packet: 421 -> 329
Cycles per packet: 156 -> 123
Instructions per cycle: 2.70 -> 2.67
Enabling MPWQE can reduce PCI bandwidth:
PCI Gen2, pktgen at fixed rate of 36864000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 80.3%
Inbound PCI utilization with MPWQE on: 59.0%
PCI Gen3, pktgen at fixed rate of 56064000 pps on 24 CPU cores:
Inbound PCI utilization with MPWQE off: 65.4%
Inbound PCI utilization with MPWQE on: 49.3%
Enabling MPWQE can also reduce CPU load, increasing the packet rate in
case of CPU bottleneck:
PCI Gen2, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 37.5 Mpps
Packet rate with MPWQE on: 49.0 Mpps
PCI Gen3, pktgen at full rate on 24 CPU cores:
Packet rate with MPWQE off: 57.0 Mpps
Packet rate with MPWQE on: 66.8 Mpps
net/mlx5e: Rename xmit-related structs to generalize them
As preparation for the upcoming TX MPWQE support for SKBs, rename struct
mlx5e_xdp_mpwqe to mlx5e_tx_mpwqe and move it above struct mlx5e_txqsq.
This structure will be reused in the regular SQ and in the regular TX
data path. Also rename mlx5e_xdp_xmit_data to mlx5e_xmit_data - it will
be used in the upcoming TX MPWQE flow.
net/mlx5e: Generalize TX MPWQE checks for full session
As preparation for the upcoming TX MPWQE for SKBs, create a function
(mlx5e_tx_mpwqe_is_full) to check whether an MPWQE session is full. This
function will be shared by MPWQE code for XDP and for SKBs. Defines are
renamed and moved to make them not XDP-specific.
TX MPWQE support for SKBs is coming in one of the following patches, and
a single MPWQE can send multiple SKBs. This commit prepares the TX path
code to handle such cases:
1. An additional FIFO for SKBs is added, just like the FIFO for DMA
chunks.
2. struct mlx5e_tx_wqe_info will contain num_fifo_pkts. If a given WQE
contains only one packet, num_fifo_pkts will be zero, and the SKB will
be stored in mlx5e_tx_wqe_info, as usual. If num_fifo_pkts > 0, the SKB
pointer will be NULL, and the SKBs will be stored in the FIFO.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.95 Mpps (±0.15 Mpps) -> 16.96 Mpps (±0.12 Mpps)
Instructions per packet: 429 -> 421
Cycles per packet: 160 -> 156
Instructions per cycle: 2.69 -> 2.70
net/mlx5e: Move the TLS resync check out of the function
Before this patch, mlx5e_ktls_tx_handle_resync_dump_comp checked for
resync_dump_frag_page. It happened for all WQEs without an SKB,
including padding WQEs, and required a function call. Normally, padding
WQEs happen more often than TLS resyncs. Take this check out of the
function and put it to an inline function to save a call on all padding
WQEs.
A constant for the number of DS in an empty WQE (i.e. a WQE without data
segments) is needed in multiple places (normal TX data path, MPWQE in
XDP), but currently we have a constant for XDP and an inline formula in
normal TX. This patch introduces a common constant.
Additionally, mlx5e_xdp_mpwqe_session_start is converted to use struct
assignment, because the code nearby is touched.
net/mlx5e: Small improvements for XDP TX MPWQE logic
Use MLX5E_XDP_MPW_MAX_WQEBBS to reserve space for a MPWQE, because it's
actually the maximal size a MPWQE can take.
Reorganize the logic that checks when to close the MPWQE session:
1. Put all checks into a single function.
2. When inline is on, make only one comparison - if it's false, the less
strict one will also be false. The compiler probably optimized it out
anyway, but it's clearer to also reflect it in the code.
The MLX5E_XDP_INLINE_WQE_* defines are also changed to make the
calculations more correct from the logical point of view. Though
MLX5E_XDP_INLINE_WQE_MAX_DS_CNT used to be 16 and didn't change its
value, the calculation used to be DIV_ROUND_UP(max inline packet size,
MLX5_SEND_WQE_DS), and the numerator should have included sizeof(struct
mlx5_wqe_inline_seg).
A huge function mlx5e_sq_xmit was split into several to achieve multiple
goals:
1. Reuse the code in IPoIB.
2. Better intergrate with TLS, IPSEC, GENEVE and checksum offloads. Now
it's possible to reserve space in the WQ before running eseg-based
offloads, so:
2.1. It's not needed to copy cseg and eseg after mlx5e_fill_sq_frag_edge
anymore.
2.2. mlx5e_txqsq_get_next_pi will be used instead of the legacy
mlx5e_fill_sq_frag_edge for better code maintainability and reuse.
3. Prepare for the upcoming TX MPWQE for SKBs. It will intervene after
mlx5e_sq_calc_wqe_attr to check if it's possible to use MPWQE, and the
code flow will split into two paths: MPWQE and non-MPWQE.
Two high-level functions are provided to send packets:
* mlx5e_xmit is called by the networking stack, runs offloads and sends
the packet. In one of the following patches, MPWQE support will be added
to this flow.
* mlx5e_sq_xmit_simple is called by the TLS offload, runs only the
checksum offload and sends the packet.
This change has no performance impact in TCP single stream test and
XDP_TX single stream test.
When compiled with a recent GCC, this change shows no visible
performance impact on UDP pktgen (burst 32) single stream test either:
Packet rate: 16.86 Mpps (±0.15 Mpps) -> 16.95 Mpps (±0.15 Mpps)
Instructions per packet: 434 -> 429
Cycles per packet: 158 -> 160
Instructions per cycle: 2.75 -> 2.69
net/mlx5e: Use struct assignment to initialize mlx5e_tx_wqe_info
Struct assignment guarantees that all fields of the structure are
initialized (those that are not mentioned are zeroed). It makes code
mode robust and reduces chances for unpredictable behavior when one
forgets to reset some field and it holds an old value from previous
iterations of using the structure.
net/mlx5e: Refactor inline header size calculation in the TX path
As preparation for the next patch, don't increase ihs to calculate
ds_cnt and then decrease it, but rather calculate the intermediate value
temporarily. This code has the same amount of arithmetic operations, but
now allows to split out ds_cnt calculation, which will be performed in
the next patch.
====================
Fix broken tc-flower rules for mscc_ocelot switches
All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 21 Sep 2020 22:56:38 +0000 (01:56 +0300)]
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaoliang Yang [Mon, 21 Sep 2020 22:56:36 +0000 (01:56 +0300)]
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 3f935c75eb52 ("inet_diag: support for wider protocol numbers") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Christoph Paasch <cpaasch@apple.com> Cc: Mat Martineau <mathew.j.martineau@linux.intel.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f9a ("bridge: add br_vlan_get_pvid_rcu()") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 22 Sep 2020 00:32:42 +0000 (17:32 -0700)]
Merge tag 'mlx5-fixes-2020-09-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Wang [Mon, 21 Sep 2020 23:09:23 +0000 (07:09 +0800)]
net: Update MAINTAINERS for MediaTek switch driver
Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.
Cc: Steven Liu <steven.liu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Landen Chao <Landen.Chao@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net>