Maxime Ripard [Wed, 21 Aug 2019 13:06:56 +0000 (15:06 +0200)]
ASoC: sun4i-i2s: Add support for DSP formats
In addition to the I2S format, the controller also supports the DSP_*
formats.
This requires some extra care on the LRCK period calculation, since the
controller, with the PCM formats, require that the value set is no longer
the periods of LRCK for a single channel, but for all of them.
Let's add the code to deal with this, and support the DSP_A and DSP_B
formats.
Maxime Ripard [Wed, 21 Aug 2019 13:06:55 +0000 (15:06 +0200)]
ASoC: sun4i-i2s: Replace call to params_width by local variable
The sun4i_i2s_hw_params function already has a variable holding the value
returned by params_width, so let's just use that variable instead of
calling params_width multiple times.
Maxime Ripard [Wed, 21 Aug 2019 13:06:54 +0000 (15:06 +0200)]
ASoC: sun4i-i2s: Use the actual format width instead of an hardcoded one
The LRCK period field in the FMT0 register holds the number of LRCK period
for one channel in I2S mode.
This has been hardcoded to 32, while it really should be the physical width
of the format, which creates an improper clock when using a 16bit format,
with the i2s controller as LRCK master.
Maxime Ripard [Wed, 21 Aug 2019 13:06:53 +0000 (15:06 +0200)]
ASoC: sun4i-i2s: Use the physical / slot width for the clocks
The clock dividers function has been using the word size to compute the
clock rate at which it's supposed to be running, but the proper formula
would be to use the physical width and / or slot width in TDM.
It doesn't make any difference at the moment since all the formats
supported have the same sample width and physical width, but it's not going
to last forever.
ASoC: soc-core: remove unneeded dai_link check from snd_soc_remove_dai_link()
snd_soc_remove_dai_link() has card connected dai_link check. but
1) we need to call list_del() anyway,
because it is "remove" function,
2) It is doing many thing for this card / dai_link already
before checking dai_link.
snd_soc_initialize_card_lists() is doing card related
INIT_LIST_HEAD(), but, it is already doing at
snd_soc_register_card(). We don't need to do it separately.
This patch merges these.
ASoC: mchp-i2s-mcc: Fix simultaneous capture and playback in master mode
This controller supports capture and playback running at the same time,
with the limitation that both capture and playback must be configured the
same way (sample rate, sample format, number of channels, etc). For this,
we have to assure that the configuration registers look the same when
capture and playback are initiated.
This patch fixes a bug in which the controller is in master mode and the
hw_params() callback fails for the second audio stream. The fail occurs
because the divisors are calculated after comparing the configuration
registers for capture and playback. The fix consists in calculating the
divisors before comparing the configuration registers. BCLK and LRC are
then configured and started only if the controller is not already running.
Maxime Ripard [Mon, 19 Aug 2019 19:25:26 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Support more channels
We've been limited to 2 channels in the driver while the controller
supports from 1 to 8 channels, in both capture and playback. let's remove
the hardcoded checks and numbers, and extend the range of channel numbers
we can use.
Maxime Ripard [Mon, 19 Aug 2019 19:25:25 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Pass the channels number as an argument
The channels number have been hardcoded to 2 so far, while the controller
supports more than that.
Remove the instance where it has been hardcoded to compute the BCLK
divider, and pass it through as an argument to ease further support of more
channels.
Maxime Ripard [Mon, 19 Aug 2019 19:25:20 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Fix the LRCK polarity
The LRCK polarity "normal" polarity in the I2S/TDM specs and in the
Allwinner datasheet are not the same. In the case where the i2s controller
is being used as the LRCK master, it's pretty clear when looked at under a
scope.
Let's fix this, and add a comment to clear up as much the confusion as
possible.
Maxime Ripard [Mon, 19 Aug 2019 19:25:19 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Fix LRCK and BCLK polarity offsets on newer SoCs
The LRCK and BCLK polarity offsets on newer SoCs has been
changed, yet the driver didn't take it into account for all of them.
This was taken into account for the H3, but not the A83t. This was handled
using a reg_field for the H3.
However, the value in that field will not be the same, so reg_field is not
adapted in that case. Let's change for proper calls with the regular
values.
Maxime Ripard [Mon, 19 Aug 2019 19:25:16 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Fix the MCLK and BCLK dividers on newer SoCs
From: Marcus Cooper <codekipper@gmail.com>
The clock division dividers have changed between the older (A10/A31) and
newer (H3, A64, etc) SoCs.
While this was addressed through an offset on some SoCs, it was missing
some dividers as well, so the support wasn't perfect. Let's introduce a
pointer in the quirk structure for the divider calculation functions to use
so we can have the proper range now.
Maxime Ripard [Mon, 19 Aug 2019 19:25:15 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Use module clock as BCLK parent on newer SoCs
On the first generation of Allwinner SoCs (A10-A31), the i2s controller was
using the MCLK as BCLK parent. However, this changed since the introduction
of the A83t and BCLK now uses the module clock as its parent.
Let's introduce a hook to get the parent rate and use that in our divider
calculations.
Maxime Ripard [Mon, 19 Aug 2019 19:25:12 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Move the format configuration to a callback
The two main generations of our I2S controller require a slightly different
format configuration, mostly because of a quite different register layout
and some additional registers being needed on the newer generation.
This used to be controlled through a bunch of booleans, however this proved
to be quite impractical, especially since a bunch of SoCs forgot to set
those parameters and therefore were broken from that point of view.
Maxime Ripard [Mon, 19 Aug 2019 19:25:11 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Move the channel configuration to a callback
The two main generations of our I2S controller require a slightly different
channel configuration, mostly because of a quite different register layout
and some additional registers being needed on the newer generation.
This used to be controlled through a bunch of booleans, however this proved
to be quite impractical, especially since a bunch of SoCs forgot to set
those parameters and therefore were broken from that point of view.
Daniel Stuart [Thu, 15 Aug 2019 17:12:55 +0000 (14:12 -0300)]
ASoC: intel: cht_bsw_max98090_ti: Add all Chromebooks that need pmc_plt_clk_0 quirk
Every single baytrail chromebook sets PMC to 0, as can be seeing
below by searching through coreboot source code:
$ grep -rl "PMC_PLT_CLK\[0\]" .
./rambi/variants/glimmer/devicetree.cb
./rambi/variants/clapper/devicetree.cb
./rambi/variants/swanky/devicetree.cb
./rambi/variants/enguarde/devicetree.cb
./rambi/variants/winky/devicetree.cb
./rambi/variants/kip/devicetree.cb
./rambi/variants/squawks/devicetree.cb
./rambi/variants/orco/devicetree.cb
./rambi/variants/ninja/devicetree.cb
./rambi/variants/heli/devicetree.cb
./rambi/variants/sumo/devicetree.cb
./rambi/variants/banjo/devicetree.cb
./rambi/variants/candy/devicetree.cb
./rambi/variants/gnawty/devicetree.cb
./rambi/variants/rambi/devicetree.cb
./rambi/variants/quawks/devicetree.cb
Plus, Cyan (only non-baytrail chromebook with max98090) also needs
this patch for audio to work.
Thus, this commit adds all the missing devices to bsw_max98090 quirk
table, implemented by commit 541c765b7fda ("ASoC: intel:
cht_bsw_max98090_ti: Add quirk for boards using pmc_plt_clk_0").
Maxime Ripard [Mon, 19 Aug 2019 19:25:13 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Rework MCLK divider calculation
The MCLK divider calculation is currently computing the ideal divider using
the oversample rate, the sample rate and the parent rate.
However, since we have access to the frequency is supposed to be running at
already, and as it turns out we're using it to compute the oversample rate,
we can just use the ratio between the parent rate and the MCLK rate to
simplify a bit the formula.
Maxime Ripard [Mon, 19 Aug 2019 19:25:10 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Replace call to params_channels by local variable
The sun4i_i2s_hw_params already has a variable holding the value returned
by params_channels, so let's just use that variable instead of calling
params_channels multiple times.
Maxime Ripard [Mon, 19 Aug 2019 19:25:14 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Don't use the oversample to calculate BCLK
The BCLK divider should be calculated using the parameters that actually
make the BCLK rate: the number of channels, the sampling rate and the
sample width.
We've been using the oversample_rate previously because in the former SoCs,
the BCLK's parent is MCLK, which in turn is being used to generate the
oversample rate, so we end up with something like this:
So, bclk_div = mclk_rate / sampling_rate / word_size / channels.
And this is actually better, since the oversampling ratio only plays a role
because the MCLK is its parent, not because of what BCLK is supposed to be.
Furthermore, that assumption of MCLK being the parent has been broken on
newer SoCs, so let's use the proper formula, and have the parent rate as an
argument.
Maxime Ripard [Mon, 19 Aug 2019 19:25:09 +0000 (21:25 +0200)]
ASoC: sun4i-i2s: Switch to devm for PCM register
Since the introduction of the driver, a new managed helper for the
dmaengine PCM registration has been created. Let's use it to simplify a bit
our probe and remove functions.
Daniel Stuart [Thu, 15 Aug 2019 17:12:55 +0000 (14:12 -0300)]
ASoC: intel: cht_bsw_max98090_ti: Add all Chromebooks that need pmc_plt_clk_0 quirk
Every single baytrail chromebook sets PMC to 0, as can be seeing
below by searching through coreboot source code:
$ grep -rl "PMC_PLT_CLK\[0\]" .
./rambi/variants/glimmer/devicetree.cb
./rambi/variants/clapper/devicetree.cb
./rambi/variants/swanky/devicetree.cb
./rambi/variants/enguarde/devicetree.cb
./rambi/variants/winky/devicetree.cb
./rambi/variants/kip/devicetree.cb
./rambi/variants/squawks/devicetree.cb
./rambi/variants/orco/devicetree.cb
./rambi/variants/ninja/devicetree.cb
./rambi/variants/heli/devicetree.cb
./rambi/variants/sumo/devicetree.cb
./rambi/variants/banjo/devicetree.cb
./rambi/variants/candy/devicetree.cb
./rambi/variants/gnawty/devicetree.cb
./rambi/variants/rambi/devicetree.cb
./rambi/variants/quawks/devicetree.cb
Plus, Cyan (only non-baytrail chromebook with max98090) also needs
this patch for audio to work.
Thus, this commit adds all the missing devices to bsw_max98090 quirk
table, implemented by commit 541c765b7fda ("ASoC: intel:
cht_bsw_max98090_ti: Add quirk for boards using pmc_plt_clk_0").
Kunihiko Hayashi [Tue, 20 Aug 2019 06:16:04 +0000 (15:16 +0900)]
ASoC: uniphier: Fix double reset assersion when transitioning to suspend state
When transitioning to supend state, uniphier_aio_dai_suspend() is called
and asserts reset lines and disables clocks.
However, if there are two or more DAIs, uniphier_aio_dai_suspend() are
called multiple times, and double reset assersion will cause.
This patch defines the counter that has the number of DAIs at first, and
whenever uniphier_aio_dai_suspend() are called, it decrements the
counter. And only if the counter is zero, it asserts reset lines and
disables clocks.
In the same way, uniphier_aio_dai_resume() are called, it increments the
counter after deasserting reset lines and enabling clocks.
Shengjiu Wang [Fri, 16 Aug 2019 05:03:14 +0000 (01:03 -0400)]
ASoC: imx-audmux: Add driver suspend and resume to support MEGA Fast
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power
source of modules during system suspend and resume procedure.
Thus, AUDMUX needs to save all the values of registers before the
system suspend and restore them after the system resume.
Pan Xiuli [Thu, 15 Aug 2019 15:57:49 +0000 (10:57 -0500)]
ASoC: SOF: Intel: initial support for Elkhart Lake
Add Kconfig, PCI ID and chip info for EHL platform.
Note that the core mask is different from previous platforms, only
Core0 can be controlled by the host. Additional patches will be
required for multi-core functionality.
Pan Xiuli [Thu, 15 Aug 2019 15:57:47 +0000 (10:57 -0500)]
ASoC: SOF: Intel: initial support for Tiger Lake.
Add Kconfig, PCI ID and chip info for Tiger Lake platform.
Note that the core mask is different from previous platforms, only
Core0 can be controlled by the host. Additional patches will be
required for multi-core functionality.
The only configuration parameter is the ALH stream ID. No range
checking is done by the driver, the firmware should check that the
stream is valid for a specific hardware.
Bump the ABI Minor number to keep the alignment with SOF firmware
Peter Ujfalusi [Tue, 13 Aug 2019 10:45:32 +0000 (13:45 +0300)]
ASoC: core: Move pcm_mutex up to card level from snd_soc_pcm_runtime
The pcm_mutex is used to prevent concurrent execution of snd_pcm_ops
callbacks. This works fine most of the cases but it can not handle setups
when the same DAI is used by different rtd, for example:
pcm3168a have two DAIs: one for Playback and one for Capture.
If the codec is connected to a single CPU DAI we need to have two dai_link
to support both playback and capture.
In this case the snd_pcm_ops callbacks can be executed in parallel causing
unexpected races in DAI drivers.
By moving the pcm_mutex up to card level this can be solved
while - hopefully - not breaking other setups.
YueHaibing [Thu, 15 Aug 2019 09:25:47 +0000 (17:25 +0800)]
ASoC: 88pm860x: remove unused variables 'pcm_switch_controls' and 'aif1_mux'
sound/soc/codecs/88pm860x-codec.c:533:38: warning:
pcm_switch_controls defined but not used [-Wunused-const-variable=]
sound/soc/codecs/88pm860x-codec.c:560:38: warning:
aif1_mux defined but not used [-Wunused-const-variable=]
YueHaibing [Thu, 15 Aug 2019 09:06:02 +0000 (17:06 +0800)]
ASoC: rt1011: remove unused variable 'dac_vol_tlv' and 'adc_vol_tlv'
sound/soc/codecs/rt1011.c:981:35: warning:
dac_vol_tlv defined but not used [-Wunused-const-variable=]
sound/soc/codecs/rt1011.c:982:35: warning:
adc_vol_tlv defined but not used [-Wunused-const-variable=]
YueHaibing [Thu, 15 Aug 2019 09:01:57 +0000 (17:01 +0800)]
ASoC: cs4349: Use PM ops 'cs4349_runtime_pm'
sound/soc/codecs/cs4349.c:358:32: warning:
cs4349_runtime_pm defined but not used [-Wunused-const-variable=]
cs4349_runtime_pm ops already defined, it seems
we should enable it.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: fdcc5a8 ("ASoC: cs4349: Add support for Cirrus Logic CS4349") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20190815090157.70036-1-yuehaibing@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
YueHaibing [Thu, 15 Aug 2019 08:54:54 +0000 (16:54 +0800)]
ASoC: cs42l73: remove unused variables 'vsp_output_mux' and 'xsp_output_mux'
sound/soc/codecs/cs42l73.c:276:38: warning:
vsp_output_mux defined but not used [-Wunused-const-variable=]
sound/soc/codecs/cs42l73.c:279:38: warning:
xsp_output_mux defined but not used [-Wunused-const-variable=]
Jiaxin Yu [Mon, 5 Aug 2019 04:56:37 +0000 (12:56 +0800)]
ASoC: mediatek: mt6358: add delay after dmic clock on
Most dmics produce a high level when they receive clock. The difference
between power-on and memory record time is about 10ms, but the dmic
needs 50ms to output normal data.
This commit add 100ms delay after SoC output clock so that we can cut
off the pop noise at the beginning.
sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c:50:1: warning:
mt8183_mt6358_ts3a227_max98357_dapm_widgets defined but not used [-Wunused-const-variable=]
sound/soc/mediatek/mt8183/mt8183-mt6358-ts3a227-max98357.c:55:1: warning:
mt8183_mt6358_ts3a227_max98357_dapm_routes defined but not used [-Wunused-const-variable=]
sound/soc/mediatek/mt8183/mt8183-da7219-max98357.c:120:1: warning:
mt8183_da7219_max98357_dapm_widgets defined but not used [-Wunused-const-variable=]
sound/soc/mediatek/mt8183/mt8183-da7219-max98357.c:124:40: warning:
mt8183_da7219_max98357_dapm_routes defined but not used [-Wunused-const-variable=]
YueHaibing [Tue, 13 Aug 2019 14:38:11 +0000 (22:38 +0800)]
ASoC: mt2701: remove unused variables
sound/soc/mediatek/mt2701/mt2701-afe-pcm.c:799:38: warning:
mt2701_afe_o23_mix defined but not used [-Wunused-const-variable=]
sound/soc/mediatek/mt2701/mt2701-afe-pcm.c:803:38: warning:
mt2701_afe_o24_mix defined but not used [-Wunused-const-variable=]
sound/soc/mediatek/mt2701/mt2701-afe-pcm.c:835:38: warning:
mt2701_afe_multi_ch_out_i2s4 defined but not used [-Wunused-const-variable=]
YueHaibing [Thu, 15 Aug 2019 09:01:57 +0000 (17:01 +0800)]
ASoC: cs4349: Use PM ops 'cs4349_runtime_pm'
sound/soc/codecs/cs4349.c:358:32: warning:
cs4349_runtime_pm defined but not used [-Wunused-const-variable=]
cs4349_runtime_pm ops already defined, it seems
we should enable it.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: fdcc5a8 ("ASoC: cs4349: Add support for Cirrus Logic CS4349") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Link: https://lore.kernel.org/r/20190815090157.70036-1-yuehaibing@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
The recent change to remove the bus->io_ops callbacks used an older
version of the SOF code base, and when merged into Mark's for-next it
invalidated changes, resulting in broken compilation identified by
kbuild and reproduced during the weekly SOF rebase.
Restore SOF code overridden by git merge and apply Takashi's intended
change in the 'right' location.
Fixes: 5e6d4e04bd1b6 ("Merge branch 'topic/hda-bus-ops-cleanup'") Reported-by: kbuild test robot <lkp@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190812190502.30729-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Cheng-Yi Chiang [Tue, 13 Aug 2019 07:44:30 +0000 (15:44 +0800)]
ASoC: rockchip: rockchip_max98090: Set period size to 240
From stress testing of arecord, we found that period size
greater than ~900 will bring pl330 to DYING state and
can not recover within 100 iterations.
The result is that arecord will stuck and get I/O error,
and issue can not be recovered until reboot.
This issue does not happen when period size is small.
Set constraint of period size to 240 to prevent such issue.
With the constraint, there will be no issue after 2000 iterations.
We can revert this patch once the root cause is found
in rockchip's pl330 implementation.
ASoC: SOF: Intel: hda: fixup HDaudio topology name with DMIC number
The SOF project maintains 6 topologies for HDaudio (iDisp or
HDaudio+iDisp, no DMIC, 2 DMICs, 4 DMICs). The user is currently
required to manually rename the topology file used in
/lib/firmware/intel/sof-tplg. We can do better to avoid such
renames and use logic to select the relevant file.
The NHLT information can be used to figure out which topology file
should be used.
Alternatively, when NHLT is not present in ACPI tables or is possibly
incorrect, a module parameter can provide that information, e.g. on
Up^2 board with the test DMIC kit.
Peter Ujfalusi [Mon, 12 Aug 2019 09:52:26 +0000 (12:52 +0300)]
ASoC: pcm3168a: Allow reconfiguration of tdm_slots and slot_width
When using right_j format and the codec is slave it can support 16bit
format, but only if slot_width == 16, in the same DAI mode the 24 bit
audio can work with 24 or 32 slot_width.
Because of this, the codec and CPU needs to be reconfigured when the sample
format changes.
ASoC: dapm: Invalidate only paths reachable for a given stream
By resetting the cached number of endpoints for all card's widgets we may
overwrite previously cached values for other streams. The situation may
happen especially when running streams simultaneously.
Jaska Uimonen [Fri, 9 Aug 2019 23:17:14 +0000 (18:17 -0500)]
ASoC: SOF: topology: use set_get_data in process load
Currently when loading sof process components there's a check if binary
control data is associated with it. If found the data is extracted to be
part of component loading and initialization. If binary data exceeds the
ipc max size, loading fails with error as large message support is only
implemented in set_get_data method. So make the process loading use
set_get_data to enable large parameters in component initialization.
Also refactor the process component loading function as it digs out 3
times almost identical information of related controls. This is
redundant, looks ugly and makes it difficult to understand the
mechanism. So make a function out of fetching the control data and use
it in process loading.
Curtis Malainey [Fri, 9 Aug 2019 21:59:51 +0000 (14:59 -0700)]
ASoC: rt5677: Revert remove superfluous set
Commit 459f7961472d90 ("ASoC: rt5677: remove superfluous set") was an
attempted code cleanup but was incorrectly tested before sent and
actually breaks the interrupt since it never resets the value on each
loop now. The breakage is most testable when hotwording code is added
and also uses the interrupt.
YueHaibing [Thu, 8 Aug 2019 14:32:15 +0000 (22:32 +0800)]
ASoC: max98926: remove two unused variables
sound/soc/codecs/max98926.c:28:26: warning:
max98926_dai_txt defined but not used [-Wunused-const-variable=]
sound/soc/codecs/max98926.c:23:27: warning:
max98926_boost_current_txt defined but not used [-Wunused-const-variable=]
ASoC: soc-core: support snd_soc_dai_link_component for aux_dev
To find aux_dev, ASoC is using .name, codec_name, codec_of_node.
Here, .name is used to fallback in case of no codec.
But, we already have this kind of component finding method by
snd_soc_dai_link_component and soc_find_component().
We shouldn't have duplicated implementation to do same things.
This patch adds snd_soc_dai_link_component support to finding aux_dev.
Now, no driver is using only .name.
All drivers are using codec_name and/or codec_of_node.
This means no driver is finding component from .name so far.
(Actually almost all drivers are using .name as just "device name",
not for finding component...)
This patch
1) add snd_soc_dai_link_component support for aux_dev. legacy style will
be removed if all drivers are switched to new style.
2) try to find component via snd_soc_dai_link_component.
Then, it doesn't try to find via .name, because no driver is using
it so far.
projects / kernel.git / log