Douglas Gilbert [Wed, 13 May 2020 01:39:43 +0000 (21:39 -0400)]
scsi: scsi_debug: Parser tables and code interaction
This patch is in response to a static analyser report from Dan Carpenter
titled: "[bug report] scsi: scsi_debug: Add per_host_store option". This
code may not clear the static analyzer reports, but may shed light on why
they occur. Amongst other things this driver has a table driven SCSI
command parser which also involves some C code. There are some invariants
between the table entries and the corresponding C code (i.e. the resp_*()
functions) that, if broken, may lead to a NULL dereference. And the report
is valid, at least in the case of the PRE-FETCH command. Alas, that is not
one of the cases that the static analyzer reported.
In this particular corner case: when the fake_rw flag is set and the table
entry for a "store"-accessing command does not have the required F_FAKE_RW
flag set, do the following. Call BUG_ON() in the devip2sip() very close to
a comment block explaining why it was called and how to fix it.
checkpatch.pl complains about the BUG_ON() but there is no reasonable
remedial action that can be taken at run time.
This change allows the code reported by the static analyzer to be
simplified. Comments were also added to the table flags (e.g. F_FAKE_RW)
so developers who add commands might be more inclined to use them
(properly).
When terminating shost_for_each_device() iteration with break or return,
scsi_device_put() should be used to prevent stale scsi device references
from being left behind.
Bart Van Assche [Mon, 18 May 2020 21:17:11 +0000 (14:17 -0700)]
scsi: qla2xxx: Fix endianness annotations in header files
Annotate members of FC protocol and firmware dump data structures as big
endian. Annotate members of RISC control structures as little endian.
Annotate mailbox registers as little endian. Annotate the mb[] arrays as
CPU-endian because communication of the mb[] values with the hardware
happens through the readw() and writew() functions. readw() converts from
__le16 to u16 and writew() converts from u16 to __le16. Annotate 'handles'
as CPU-endian because for the firmware these are opaque values.
Link: https://lore.kernel.org/r/20200518211712.11395-15-bvanassche@acm.org CC: Hannes Reinecke <hare@suse.de> Cc: Nilesh Javali <njavali@marvell.com> Cc: Quinn Tran <qutran@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:17:09 +0000 (14:17 -0700)]
scsi: qla2xxx: Cast explicitly to uint16_t / uint32_t
Casting a pointer to void * and relying on an implicit cast from void *
to uint16_t or uint32_t suppresses sparse warnings about endianness. Hence
cast explicitly to uint16_t and uint32_t. Additionally, remove superfluous
void * casts.
Link: https://lore.kernel.org/r/20200518211712.11395-13-bvanassche@acm.org Cc: Arun Easi <aeasi@marvell.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Daniel Wagner <dwagner@suse.de> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:17:07 +0000 (14:17 -0700)]
scsi: qla2xxx: Fix the code that reads from mailbox registers
Make the MMIO accessors strongly typed such that the compiler checks
whether the accessor function is used that matches the register width. Fix
those MMIO accesses where another number of bits was read or written than
the size of the register.
Link: https://lore.kernel.org/r/20200518211712.11395-11-bvanassche@acm.org Cc: Nilesh Javali <njavali@marvell.com> Cc: Quinn Tran <qutran@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:17:06 +0000 (14:17 -0700)]
scsi: qla2xxx: Use register names instead of register offsets
Make qla27xx_write_remote_reg() easier to read by using register names
instead of register offsets. The 'pahole' tool has been used to convert
register offsets into register names. See also commit cbb01c2f2f63 ("scsi:
qla2xxx: Fix MPI failure AEN (8200) handling").
Link: https://lore.kernel.org/r/20200518211712.11395-10-bvanassche@acm.org Cc: Arun Easi <aeasi@marvell.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:17:04 +0000 (14:17 -0700)]
scsi: qla2xxx: Increase the size of struct qla_fcp_prio_cfg to FCP_PRIO_CFG_SIZE
This patch fixes the following Coverity complaint without changing any
functionality:
CID 337793 (#1 of 1): Wrong size argument (SIZEOF_MISMATCH)
suspicious_sizeof: Passing argument ha->fcp_prio_cfg of type
struct qla_fcp_prio_cfg * and argument 32768UL to function memset is
suspicious because a multiple of sizeof (struct qla_fcp_prio_cfg) /*48*/
is expected.
memset(ha->fcp_prio_cfg, 0, FCP_PRIO_CFG_SIZE);
Link: https://lore.kernel.org/r/20200518211712.11395-8-bvanassche@acm.org Cc: Nilesh Javali <njavali@marvell.com> Cc: Quinn Tran <qutran@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:17:00 +0000 (14:17 -0700)]
scsi: qla2xxx: Simplify the functions for dumping firmware
Instead of passing an argument to the firmware dumping functions that tells
these functions whether or not to obtain the hardware lock, obtain that
lock before calling these functions. This patch fixes the following
recently introduced C=2 build error:
CHECK drivers/scsi/qla2xxx/qla_tmpl.c
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: Expected ; at end of statement
drivers/scsi/qla2xxx/qla_tmpl.c:1133:1: error: got }
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: Expected } at end of function
drivers/scsi/qla2xxx/qla_tmpl.h:247:0: error: got end-of-input
Link: https://lore.kernel.org/r/20200518211712.11395-4-bvanassche@acm.org Fixes: cbb01c2f2f63 ("scsi: qla2xxx: Fix MPI failure AEN (8200) handling") Cc: Arun Easi <aeasi@marvell.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Martin Wilck <mwilck@suse.com> Cc: Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche [Mon, 18 May 2020 21:16:59 +0000 (14:16 -0700)]
scsi: qla2xxx: Suppress two recently introduced compiler warnings
Suppress the following two compiler warnings because these are not useful:
In file included from ./include/trace/define_trace.h:102,
from ./include/trace/events/qla.h:39,
from drivers/scsi/qla2xxx/qla_dbg.c:77:
./include/trace/events/qla.h: In function 'trace_event_raw_event_qla_log_event':
./include/trace/trace_events.h:691:9: warning: function 'trace_event_raw_event_qla_log_event' might be a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format]
691 | struct trace_event_raw_##call *entry; \
| ^~~~~~~~~~~~~~~~
./include/trace/events/qla.h:12:1: note: in expansion of macro 'DECLARE_EVENT_CLASS'
12 | DECLARE_EVENT_CLASS(qla_log_event,
| ^~~~~~~~~~~~~~~~~~~
In file included from ./include/trace/define_trace.h:103,
from ./include/trace/events/qla.h:39,
from drivers/scsi/qla2xxx/qla_dbg.c:77:
./include/trace/events/qla.h: In function 'perf_trace_qla_log_event':
./include/trace/perf.h:41:9: warning: function 'perf_trace_qla_log_event' might be a candidate for 'gnu_printf' format attribute [-Wsuggest-attribute=format]
41 | struct hlist_head *head; \
| ^~~~~~~~~~
./include/trace/events/qla.h:12:1: note: in expansion of macro 'DECLARE_EVENT_CLASS'
Link: https://lore.kernel.org/r/20200518211712.11395-3-bvanassche@acm.org Fixes: 598a90f2002c ("scsi: qla2xxx: add ring buffer for tracing debug logs") Cc: Rajan Shanmugavelu <rajan.shanmugavelu@oracle.com> Cc: Joe Jin <joe.jin@oracle.com> Cc: Nilesh Javali <njavali@marvell.com> Cc: Quinn Tran <qutran@marvell.com> Cc: Martin Wilck <mwilck@suse.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Arun Easi <aeasi@marvell.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bodo Stroesser [Mon, 18 May 2020 16:48:33 +0000 (18:48 +0200)]
scsi: target: tcmu: Userspace must not complete queued commands
When tcmu queues a new command - no matter whether in command ring or in
qfull_queue - a cmd_id from IDR udev->commands is assigned to the command.
If userspace sends a wrong command completion containing the cmd_id of a
command on the qfull_queue, tcmu_handle_completions() finds the command in
the IDR and calls tcmu_handle_completion() for it. This might do some nasty
things because commands in qfull_queue do not have a valid dbi list.
To fix this bug, we no longer add queued commands to the idr. Instead the
cmd_id is assign when a command is written to the command ring.
Due to this change I had to adapt the source code at several places where
up to now an idr_for_each had been done.
Lance Digby [Mon, 18 May 2020 01:02:16 +0000 (11:02 +1000)]
scsi: target: core: Add initiatorname to NON_EXISTENT_LUN error
The NON_EXISTENT_LUN error can be written without an error condition
on the initiator responsible. Adding the initiatorname to this message
will reduce the effort required to fix this when many initiators are
supported by a target.
This version ensures the initiator name is also printed on the same message
in transport_lookup_tmr_lun for consistency.
Luo Jiaxing [Fri, 15 May 2020 14:13:44 +0000 (22:13 +0800)]
scsi: hisi_sas: Add SAS_RAS_INTR0 to debugfs register name list
Register SAS_RAS_INTR0 can help us to figure out which ECC error has
occurred. This register is helpful to identify RAS issue, so we add it to
the list of debugfs register name list for easier retrieval.
Luo Jiaxing [Fri, 15 May 2020 14:13:42 +0000 (22:13 +0800)]
scsi: hisi_sas: Do not reset phy timer to wait for stray phy up
We found out that after phy up, the hardware reports another oob interrupt
but did not follow a phy up interrupt:
oob ready -> phy up -> DEV found -> oob read -> wait phy up -> timeout
We run link reset when wait phy up timeout, and it send a normal disk into
reset processing. So we made some circumvention action in the code, so that
this abnormal oob interrupt will not start the timer to wait for phy up.
Damien Le Moal [Fri, 15 May 2020 05:48:56 +0000 (14:48 +0900)]
scsi: sd: Add zoned capabilities device attribute
Export through sysfs as a scsi_disk attribute the zoned capabilities of a
disk ("zoned_cap" attribute file). This new attribute indicates in human
readable form (i.e. a string) the zoned block capabilities implemented by
the disk as found in the ZONED field of the disk block device
characteristics VPD page. The possible values are:
- "none": ZONED=00b (not reported), regular disk
- "host-aware": ZONED=01b, host-aware ZBC disk
- "drive-managed": ZONED=10b, drive-managed ZBC disk (regular disk
interface)
For completeness, also add the following value which is detected using the
device type rather than the ZONED field:
- "host-managed": device type = 0x14 (TYPE_ZBC), host-managed ZBC disk
This new sysfs attribute is purely informational and complementary to the
"zoned" device request queue sysfs attribute as it allows applications and
user daemons (e.g. udev) to easily differentiate regular disks from
drive-managed SMR disks without the need for direct access tools such as
provided by sg3utils.
Bart Van Assche [Thu, 7 May 2020 22:27:50 +0000 (15:27 -0700)]
scsi: ufs: Make ufshcd_wait_for_register() sleep instead of busy-waiting
The ufshcd_wait_for_register() function either sleeps or spins until the
specified register has reached the desired value. Busy-waiting is not only
considered a bad practice but also has a bad impact on energy
consumption. Always sleep instead of spinning by making sure that all
ufshcd_wait_for_register() calls happen from a context where it is allowed
to sleep. The only function call that has to be moved is the
ufshcd_hba_stop() call in ufshcd_host_reset_and_restore().
Link: https://lore.kernel.org/r/20200507222750.19113-1-bvanassche@acm.org Cc: Can Guo <cang@codeaurora.org> Cc: Avri Altman <avri.altman@wdc.com> Cc: Bean Huo <beanhuo@micron.com> Cc: Alim Akhtar <alim.akhtar@samsung.com> Cc: Asutosh Das <asutoshd@codeaurora.org> Tested-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Thu, 14 May 2020 08:19:53 +0000 (17:19 +0900)]
scsi: sd: Signal drive managed SMR disks
Print a message indicating that a disk is a drive-managed SMR model when
such drive is found using the ZONED field of the Block Device
Characteristics VPD page (IDENTIFY data on ATA side).
Dan Carpenter [Wed, 13 May 2020 09:37:03 +0000 (12:37 +0300)]
scsi: aacraid: Fix an oops in error handling
If the memdup_user() function fails then it results in an Oops in the
error handling code when we try to kfree() and error pointer.
Link: https://lore.kernel.org/r/20200513093703.GB347693@mwanda Fixes: 8d925b1f00e6 ("scsi: aacraid: Use memdup_user() as a cleanup") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20200512113258.30781-1-yanaijie@huawei.com Cc: John Garry <john.garry@huawei.com> Cc: Xiang Chen <chenxiang66@hisilicon.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Sat, 9 May 2020 10:04:08 +0000 (13:04 +0300)]
scsi: scsi_debug: Fix an error handling bug in sdeb_zbc_model_str()
This test is checking the wrong variable. It should be testing "res".
The "sdeb_zbc_model" variable is an enum (unsigned in this situation)
and we never assign negative values to it.
[mkp: fixed commit desc issue reported by Doug]
Link: https://lore.kernel.org/r/20200509100408.GA5555@mwanda Fixes: 9267e0eb41fe ("scsi: scsi_debug: Add ZBC module parameter") Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Benjamin Block [Fri, 8 May 2020 17:23:35 +0000 (19:23 +0200)]
scsi: zfcp: Move allocation of the shost object to after xconf- and xport-data
At the moment we allocate and register the Scsi_Host object corresponding
to a zfcp adapter (FCP device) very early in the life cycle of the adapter
- even before we fully discover and initialize the underlying
firmware/hardware. This had the advantage that we could already use the
Scsi_Host object, and fill in all its information during said discover and
initialize.
Due to commit 737eb78e82d5 ("block: Delay default elevator initialization")
(first released in v5.4), we noticed a regression that would prevent us
from using any storage volume if zfcp is configured with support for DIF or
DIX (zfcp.dif=1 || zfcp.dix=1). Doing so would result in an illegal memory
access as soon as the first request is sent with such an configuration. As
example for a crash resulting from this:
While this issue is exposed by the commit named above, this is only by
accident. The real issue exists for longer already - basically since it's
possible to use blk-mq via scsi-mq, and blk-mq pre-allocates all requests
for a tag-set during initialization of the same. For a given Scsi_Host
object this is done when adding the object to the midlayer
(`scsi_add_host()` and such). In `scsi_mq_setup_tags()` the midlayer
calculates how much memory is required for a single scsi_cmnd, and its
additional data, which also might include space for additional protection
data - depending on whether the Scsi_Host has any form of protection
capabilities (`scsi_host_get_prot()`).
The problem is now thus, because zfcp does this step before we actually
know whether the firmware/hardware has these capabilities, we don't set any
protection capabilities in the Scsi_Host object. And so, no space is
allocated for additional protection data for requests in the Scsi_Host
tag-set.
Once we go through discover and initialize the FCP device firmware/hardware
fully (this is done via the firmware commands "Exchange Config Data" and
"Exchange Port Data") we find out whether it actually supports DIF and DIX,
and we set the corresponding capabilities in the Scsi_Host object (in
`zfcp_scsi_set_prot()`). Now the Scsi_Host potentially has protection
capabilities, but the already allocated requests in the tag-set don't have
any space allocated for that.
When we then trigger target scanning or add scsi_devices manually, the
midlayer will use requests from that tag-set, and before sending most
requests, it will also call `scsi_mq_prep_fn()`. To prepare the scsi_cmnd
this function will check again whether the used Scsi_Host has any
protection capabilities - and now it potentially has - and if so, it will
try to initialize the assumed to be preallocated structures and thus it
causes the crash, like shown above.
Before delaying the default elevator initialization with the commit named
above, we always would also allocate an elevator for any scsi_device before
ever sending any requests - in contrast to now, where we do it after
device-probing. That elevator in turn would have its own tag-set, and that
is initialized after we went through discovery and initialization of the
underlying firmware/hardware. So requests from that tag-set can be
allocated properly, and if used - unless the user changes/disabled the
default elevator - this would hide the underlying issue.
To fix this for any configuration - with or without an elevator - we move
the allocation and registration of the Scsi_Host object for a given FCP
device to after the first complete discovery and initialization of the
underlying firmware/hardware. By doing that we can make all basic
properties of the Scsi_Host known to the midlayer by the time we call
`scsi_add_host()`, including whether we have any protection capabilities.
To do that we have to delay all the accesses that we would have done in the
past during discovery and initialization, and do them instead once we are
finished with it. The previous patches ramp up to this by fencing and
factoring out all these accesses, and make it possible to re-do them later
on. In addition we make also use of the diagnostic buffers we recently
added with
commit 92953c6e0aa7 ("scsi: zfcp: signal incomplete or error for sync exchange config/port data")
commit 7e418833e689 ("scsi: zfcp: diagnostics buffer caching and use for exchange port data")
commit 088210233e6f ("scsi: zfcp: add diagnostics buffer for exchange config data")
(first released in v5.5), because these already cache all the information
we need for that "re-do operation" - the information cached are always
updated during xconf or xport data, so it won't be stale.
In addition to the move and re-do, this patch also updates the
function-documentation of `zfcp_scsi_adapter_register()` and changes how it
reports if a Scsi_Host object already exists. In that case future
recovery-operations can skip this step completely and behave much like they
would do in the past - zfcp does not release a once allocated Scsi_Host
object unless the corresponding FCP device is deconstructed completely.
Benjamin Block [Fri, 8 May 2020 17:23:34 +0000 (19:23 +0200)]
scsi: zfcp: Fence early sysfs interfaces for accesses of shost objects
When setting an adapter online for the first time, we also create a couple
of entries for it in the sysfs device tree. This is also true even if the
adapter has not yet ever gone successfully through exchange config and
exchange port data.
When moving the scsi host object allocation and registration to after the
first exchange config and exchange port data, this make the `port_rescan`
attribute susceptible to invalid pointer-dereferences of the shost field
before the adapter is fully initialized.
When written to, it schedules a `scan_work` item that will in turn make use
of the associated fibre channel host object to check the topology used for
this FCP device.
Because scanning for remote ports can't be done successfully without
completing exchange config and exchange port data first, we can simply
fence `port_rescan`, and so prevent the illegal access.
As with cases where we can't get a reference to the adapter, we also return
-ENODEV here. Applications need to handle that errno today already.
After a successful allocation of the scsi host object nothing changes in
the work flow.
Benjamin Block [Fri, 8 May 2020 17:23:33 +0000 (19:23 +0200)]
scsi: zfcp: Fence adapter status propagation for common statuses
Common status flags that all main objects - adapter, port, and unit -
support are propagated to sub-objects when set or cleared. For instance,
when setting the status ZFCP_STATUS_COMMON_ERP_INUSE for an adapter object,
we will propagate this to all its child ports and units - same for when
clearing a common status flag.
Units of an adapter object are enumerated via __shost_for_each_device()
over the scsi host object of the corresponding adapter.
Once we move the scsi host object allocation and registration to after the
first exchange config and exchange port data, this won't be possible for
cases where we set or clear common statuses during the very first adapter
recovery.
But since we won't have any port or unit objects yet at that point of time,
we can just fence the status propagation for cases where the scsi host
object is not yet set in the adapter object. It won't change any effective
status propagations, but will prevent us from dereferencing invalid
pointers.
For any later point in the work flow the scsi host object will be set and
thus nothing is changed then.
Benjamin Block [Fri, 8 May 2020 17:23:32 +0000 (19:23 +0200)]
scsi: zfcp: Move p-t-p port allocation to after xport data
When doing the very first adapter recovery - initialization - for a FCP
device in a point-to-point topology we also allocate the port object
corresponding to the attached remote port, and trigger a port recovery for
it that will run after the adapter recovery finished.
Right now this happens right after we finished with the exchange config
data command, and uses the fibre channel host object corresponding to the
FCP device to determine whether a point-to-point topology is used.
When moving the scsi host object allocation and registration - and thus
also the fibre channel host object allocation - to after the first exchange
config and exchange port data, this use of the fc_host object is not
possible anymore at that point in the work flow.
But the allocation and recovery trigger doesn't have notable side-effects
on the following exchange port data processing, so we can move those to
after xport data, and thus also to after the scsi host object allocation,
once we move it. Then the fc_host object can be used again, like it is now.
For any further adapter recoveries this doesn't change anything, because at
that point the port object already exists and recovery is triggered
elsewhere for existing port objects.
Benjamin Block [Fri, 8 May 2020 17:23:31 +0000 (19:23 +0200)]
scsi: zfcp: Fence fc_host updates during link-down handling
When receiving a notification that a FCP device lost its local link we
usually update the fibre channel host object which represents that FCP
device to reflect that.
This notification/information can also surface when the FCP device is
running through adapter recovery (exchange config and exchange port data
return incomplete).
When moving the scsi host object allocation and registration - and thus
also the fibre channel host object allocation - to after the first exchange
config and exchange port data, and this happens during the very first
adapter recovery, these updates can not be done until after the scsi host
object is allocated.
Reorder the fc_host updates in zfcp_fsf_fc_host_link_down() so that they
only happen after a check of whether the scsi host object is already
allocated or not.
During the first adapter recovery this will cause the skip of these updates
if a link-down condition is detected, but we can repeat them after we
allocated the scsi host object, if necessary.
For any further link-down handling the only changes in the work flow are
the slightly reordered assignments in zfcp_fsf_fc_host_link_down().
Benjamin Block [Fri, 8 May 2020 17:23:30 +0000 (19:23 +0200)]
scsi: zfcp: Move fc_host updates during xport data handling into fenced function
When executing exchange port data for a FCP device for the first time, or
after an adapter recovery, we update several properties of the fibre
channel host object which represents that FCP device.
When moving the scsi host object allocation and registration - and thus
also the fibre channel host object allocation - to after the first exchange
config and exchange port data, this is not possible for the former case.
Move all these update into separate, and fenced function that first checks
whether the scsi host object already exists or not, before making the
updates.
During the first ever exchange port data in the adapter life cycle this
will make the exchange port data handler skip over this update step, but we
can repeat it later, after we allocated the scsi host object.
For any further recovery of that adapter the work flow is only changed
slightly because then the scsi host object already exists and we don't free
it until we release the adapter completely at the end of its life cycle.
Benjamin Block [Fri, 8 May 2020 17:23:29 +0000 (19:23 +0200)]
scsi: zfcp: Move shost updates during xconfig data handling into fenced function
When executing exchange config data for a FCP device for the first time, or
after an adapter recovery, we update several properties of the scsi host or
fibre channel host object that represent that FCP device.
When moving the scsi host object allocation and registration - and thus
also the fibre channel host object allocation - to after the first exchange
config and exchange port data, this is not possible for the former case.
Move all these update into separate, and fenced function that first checks
whether the scsi host object already exists or not, before making the
updates.
During the first ever exchange config data in the adapter life cycle this
will make the exchange config data handler skip over this update step, but
we can repeat it later, after we allocated the scsi host object.
For any further recovery of that adapter the work flow is only changed
slightly because then the scsi host object already exists and we don't free
it until we release the adapter completely at the end of its life cycle.
Benjamin Block [Fri, 8 May 2020 17:23:28 +0000 (19:23 +0200)]
scsi: zfcp: Move shost modification after QDIO (re-)open into fenced function
When establishing and activating the QDIO queue pair for a FCP device for
the first time, or after an adapter recovery, we publish some of its
characteristics to the scsi host object representing that FCP device.
When moving the scsi host object allocation and registration to after the
first exchange config and exchange port data, this is not possible for the
former case - QDIO open for the first time - because that happens before
exchange config and exchange port data.
Move the scsi host object update into a fenced function that checks whether
the object already exists or not. This way we can repeat that step later,
once we are past the allocation.
Once the first recovery succeeds we don't release the scsi host object
anymore, so further recoveries do work as before.
Shivasharan S [Fri, 8 May 2020 08:51:30 +0000 (14:21 +0530)]
scsi: megaraid_sas: Replace undefined MFI_BIG_ENDIAN macro with __BIG_ENDIAN_BITFIELD macro
MFI_BIG_ENDIAN macro used in drivers structure bitfield to check the CPU
big endianness is undefined which would break the code on big endian
machine. __BIG_ENDIAN_BITFIELD kernel macro should be used in places of
MFI_BIG_ENDIAN macro.
Link: https://lore.kernel.org/r/20200508085130.23339-1-chandrakanth.patil@broadcom.com Fixes: a7faf81d7858 ("scsi: megaraid_sas: Set no_write_same only for Virtual Disk") Cc: <stable@vger.kernel.org> # v5.6+ Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As blk_queue_virt_boundary() API in slave_configure ensures that no IOs
will come with holes/gaps. Hence, code logic to detect the holes/gaps in IO
buffer is not required.
Stanley Chu [Fri, 8 May 2020 08:01:15 +0000 (16:01 +0800)]
scsi: ufs: Cleanup WriteBooster feature
Small cleanup as below items,
1. Use ufshcd_is_wb_allowed() directly instead of ufshcd_wb_sup() since
ufshcd_wb_sup() just returns the result of ufshcd_is_wb_allowed().
2. In ufshcd_suspend(), "else if (!ufshcd_is_runtime_pm(pm_op)) can be
simplified to "else" since both have the same meaning.
This patch does not change any functionality.
Link: https://lore.kernel.org/r/20200508080115.24233-9-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable WriteBooster capability on MediaTek UFS platforms.
Link: https://lore.kernel.org/r/20200508080115.24233-8-stanley.chu@mediatek.com Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:13 +0000 (16:01 +0800)]
scsi: ufs: Add LU Dedicated buffer mode support for WriteBooster
According to UFS specification, there are two WriteBooster mode of
operations: "LU dedicated buffer" mode and "shared buffer" mode. In the
"LU dedicated buffer" mode, the WriteBooster Buffer is dedicated to a
logical unit.
If the device supports the "LU dedicated buffer" mode, this mode is
configured by setting bWriteBoosterBufferType to 00h. The logical unit
WriteBooster Buffer size is configured by setting the
dLUNumWriteBoosterBufferAllocUnits field of the related Unit
Descriptor. Only a value greater than zero enables the WriteBooster feature
in the logical unit.
Modify ufshcd_wb_probe() as above description to support LU Dedicated
buffer mode.
Note that according to UFS 3.1 specification, the valid value of
bDeviceMaxWriteBoosterLUs parameter in Geometry Descriptor is 1, which
means at most one LUN can have WriteBooster buffer in "LU dedicated buffer
mode". Therefore this patch supports only one LUN with WriteBooster
enabled. All WriteBooster related sysfs nodes are specifically mapped to
the LUN with WriteBooster enabled in LU Dedicated buffer mode.
Link: https://lore.kernel.org/r/20200508080115.24233-7-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:12 +0000 (16:01 +0800)]
scsi: ufs: Add "index" in parameter list of ufshcd_query_flag()
For preparation of LU Dedicated buffer mode support on WriteBooster
feature, "index" parameter shall be added and allowed to be specified by
callers.
Link: https://lore.kernel.org/r/20200508080115.24233-6-stanley.chu@mediatek.com Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Can Guo <cang@codeaurora.org> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:11 +0000 (16:01 +0800)]
scsi: ufs-mediatek: Add fixup_dev_quirks vops
Add fixup_dev_quirk vops in MediaTek UFS platforms and provide an initial
vendor-specific device quirk table.
Link: https://lore.kernel.org/r/20200508080115.24233-5-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:10 +0000 (16:01 +0800)]
scsi: ufs: Export ufs_fixup_device_setup() function
Export ufs_fixup_device_setup() to allow vendors to re-use it for fixing
device quriks on specified UFS hosts.
Link: https://lore.kernel.org/r/20200508080115.24233-4-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:09 +0000 (16:01 +0800)]
scsi: ufs: Introduce fixup_dev_quirks vops
Some UFS deivces may have required device quirks or have non-standard
features which are enabled only on specified UFS hosts or for special
customers.
To not "pollute" common device quirk list, i.e. ufs_fixups table, for those
devices mentioned above, introduce "fixup_dev_quirks" vops to allow vendors
to fix or modify device quirks accordingly.
Link: https://lore.kernel.org/r/20200508080115.24233-3-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stanley Chu [Fri, 8 May 2020 08:01:08 +0000 (16:01 +0800)]
scsi: ufs: Enable WriteBooster on some pre-3.1 UFS devices
The WriteBooster feature can be supported by some pre-3.1 UFS devices by
upgrading firmware.
To enable WriteBooster feature in such devices, introduce a device quirk to
relax the entrance condition of ufshcd_wb_probe() to allow host driver to
check those devices' WriteBooster capability.
WriteBooster feature can be available if below all conditions are
satisfied,
1. Host enables WriteBooster capability
2. UFS 3.1 device or UFS pre-3.1 device with quirk
UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES enabled
3. The device descriptor shall have DEVICE_DESC_PARAM_EXT_UFS_FEATURE_SUP
field
4. WriteBooster support is specified in above field
Link: https://lore.kernel.org/r/20200508080115.24233-2-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Thu, 7 May 2020 20:31:11 +0000 (21:31 +0100)]
scsi: lpfc: Remove redundant initialization to variable rc
The variable rc is being initialized with a value that is never read and it
is being updated later with a new value. The initialization is redundant
and can be removed.
scsi: ufs: Replace zero-length array with flexible-array
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in which
the sizeof operator is being incorrectly/erroneously applied to zero-length
arrays and the result is zero. Such instances may be hiding some bugs. So,
this work (flexible-array member conversions) will also help to get
completely rid of those sorts of issues.
scsi: libsas: Replace zero-length array with flexible-array
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these ones is a flexible array member[1][2], introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by this
change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in which
the sizeof operator is being incorrectly/erroneously applied to zero-length
arrays and the result is zero. Such instances may be hiding some bugs. So,
this work (flexible-array member conversions) will also help to get
completely rid of those sorts of issues.
Link: https://lore.kernel.org/r/20200507192147.GA16206@embeddedor Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bodo Stroesser [Tue, 28 Apr 2020 18:26:17 +0000 (20:26 +0200)]
scsi: target: loopback: Fix READ with data and sensebytes
We use tcm_loop with tape emulations running on tcmu.
In case application reads a short tape block with a longer READ, or a long
tape block with a short READ, according to SCC spec data has to be
tranferred _and_ sensebytes with ILI set and information field containing
the residual count. Similar problem also exists when using fixed block
size in READ.
Up to now tcm_loop is not prepared to handle sensebytes if input data is
provided, as in tcm_loop_queue_data_in() it only sets SAM_STAT_GOOD and, if
necessary, the residual count.
To fix the bug, the same handling for sensebytes as present in
tcm_loop_queue_status() must be done in tcm_loop_queue_data_in() also.
After adding this handling, the two function now are nearly identical, so I
created a single function with two wrappers.
Dick Kennedy [Fri, 1 May 2020 21:43:10 +0000 (14:43 -0700)]
scsi: lpfc: Update lpfc version to 12.8.0.1
Update lpfc version to 12.8.0.1
Link: https://lore.kernel.org/r/20200501214310.91713-10-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The MDS diagnostic enablement bit for the adapter interface is incorrect in
the driver header.
Correct the bit position for the SET_FEATURE MDS bit.
Link: https://lore.kernel.org/r/20200501214310.91713-9-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy [Fri, 1 May 2020 21:43:08 +0000 (14:43 -0700)]
scsi: lpfc: Fix noderef and address space warnings
Running make C=1 M=drivers/scsi/lpfc triggers sparse warnings
Correct the code generating the following errors:
- Incompatible address space assignment without proper conversion.
- Deference of usespace and per-cpu pointers.
Link: https://lore.kernel.org/r/20200501214310.91713-8-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In an audit of lockdep calls in the driver, there are multiple lockdep
checks in successive calling layers. E.g. a routine checks, and then calls
a lower routine that also checks, and so on. Calling sequences result in
many redundant checks.
Refine the code to remove lower-level lockdep checks. Update comments on
the lock, correcting a few places where lock object in comment was
incorrect.
Link: https://lore.kernel.org/r/20200501214310.91713-7-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy [Fri, 1 May 2020 21:43:06 +0000 (14:43 -0700)]
scsi: lpfc: Change default queue allocation for reduced memory consumption
By default, the driver attempts to allocate a hdwq per logical cpu in order
to provide good cpu affinity. Some systems have extremely high cpu counts
and this can significantly raise memory consumption.
In testing on x86 platforms (non-AMD) it is found that sharing of a hdwq by
a physical cpu and its HT cpu can occur with little performance
degredation. By sharing, the hdwq count can be halved, significantly
reducing the memory overhead.
Change the default behavior of the driver on non-AMD x86 platforms to
share a hdwq by the cpu and its HT cpu.
Link: https://lore.kernel.org/r/20200501214310.91713-6-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy [Fri, 1 May 2020 21:43:05 +0000 (14:43 -0700)]
scsi: lpfc: Fix negation of else clause in lpfc_prep_node_fc4type
Implementation of a previous patch added a condition to an if check that
always end up with the if test being true. Execution of the else clause was
inadvertently negated. The additional condition check was incorrect and
unnecessary after the other modifications had been done in that patch.
Remove the check from the if series.
Link: https://lore.kernel.org/r/20200501214310.91713-5-jsmart2021@gmail.com Fixes: b95b21193c85 ("scsi: lpfc: Fix loss of remote port after devloss due to lack of RPIs") Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy [Fri, 1 May 2020 21:43:04 +0000 (14:43 -0700)]
scsi: lpfc: Remove re-binding of nvme rport during registration
The lldd rebinds the ndlp with rport during a nvme rport registration (via
nvme_fc_register_remoteport). If rport & ndlp pointers are same as the
previous one, the lldd will re-use the ndlp and rport association without
re-initialization. This assumption is incorrect. The lldd should be
ignorant of whether the returned rport pointer is new or not, and should
always assume it is new.
Remove the re-binding code, always assumes that rport pointer received from
transport is a new pointer.
Link: https://lore.kernel.org/r/20200501214310.91713-4-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dick Kennedy [Fri, 1 May 2020 21:43:03 +0000 (14:43 -0700)]
scsi: lpfc: Maintain atomic consistency of queue_claimed flag
A previous change introduced the atomic use of queue_claimed flag for eq's
and cq's. The code works fine, but the clearing of the queue_claimed flag
is not atomic.
Change queue_claimed = 0 into xchg(&queue_claimed, 0) to be consistent for
change under atomicity.
Link: https://lore.kernel.org/r/20200501214310.91713-3-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bodo Stroesser [Mon, 27 Apr 2020 15:08:23 +0000 (17:08 +0200)]
scsi: target: tcmu: Make pgr_support and alua_support attributes writable
Currently in tcmu reservation commands are handled by core's pr
implementation (default) or completely rejected (emulate_pr set to 0). We
additionally want to be able to do full reservation handling in
userspace. Therefore we need a way to set TRANSPORT_FLAG_PASSTHROUGH_PGR.
The inverted flag is displayed by attribute pgr_support. Since we moved
the flag from transport/backend to se_device in the previous commit, we now
can make it changeable per device by allowing to write the attribute. The
new field transport_flags_changeable in transport/backend is used to reject
writing if not allowed for a backend.
Regarding ALUA we also want to be able to passthrough commands to userspace
in tcmu. Therefore we need TRANSPORT_FLAG_PASSTHROUGH_ALUA to be
changeable, because by setting it we can switch off all ALUA checks in
core. So we also set TRANSPORT_FLAG_PASSTHROUGH_ALUA in tcmu's
transport_flags_changeable.
Of course, ALUA and reservation handling in userspace will work only, if
session/nexus information is sent to userspace along with every
command. This will be object of a patch series announced by Mike Christie.
These attributes are per device, while the flags are per backend. Rename
the transport_flags in backend/transport to transport_flags_default and use
this value to initialize the new transport_flags field in the se_device
structure.
Bodo Stroesser [Mon, 27 Apr 2020 15:08:21 +0000 (17:08 +0200)]
scsi: target: tcmu: Add attributes enforce_pr_isids and force_pr_aptpl
tcmu has not set TRANSPORT_FLAG_PASSTHROUGH_PGR. Therefore the in-core pr
emulation is active by default, but there are some attributes for
configuration missing. Add them.
Bodo Stroesser [Mon, 27 Apr 2020 15:08:20 +0000 (17:08 +0200)]
scsi: target: Add missing emulate_pr attribute to passthrough backends
In commit b49d6f788530 ("scsi: target: add emulate_pr backstore attr to
toggle PR support") the new attribute emulate_pr was added.
passthrough_parse_cdb() uses the attribute's value to distinguish whether
reservation commands should be rejected or not. But the new attribute was
not added to passthrough_attrib_attrs, so in pscsi and tcmu - the users of
passthrough_parse_cdb() - the attribute is not available to change parser's
behavior.
scsi: mpt3sas: Disable DIF when prot_mask set to zero
By default DIF Type 1, DIF Type 2 & DIF Type 3 will be enabled. Also,
users can enable either DIF Type 1 or DIF Type 2 or DIF Type 3 or in any
combination using the prot_mask module parameter.
However, when the user provides a prot_mask module parameter value of zero,
then the driver is not disabling the DIF. Instead it enables all three
types.
Modify the driver to disable the DIF support if the user provides a
prot_mask module parameter value of zero.
Suganath Prabu [Tue, 28 Apr 2020 06:45:22 +0000 (02:45 -0400)]
scsi: mpt3sas: Capture IOC data for debugging purposes
Information needed to debug driver problems and firmware faults is stored
in the IOC’s MPT3SAS_ADAPTER data structure. Parameters such as IOCFacts,
IOC flags (related to sge, MSI-X, error recovery etc.), performance mode
type, TMs, internal commands reply status, etc. are present.
For debugging purposes, it is therefore helpful to be able to capture this
information so that the fault can be analyzed. Export the MPT3SAS_ADAPTER
data structure in debugfs. The data is available in:
Jason Yan [Thu, 30 Apr 2020 12:17:06 +0000 (20:17 +0800)]
scsi: qedi: Remove comparison of 0/1 to bool variable
Fix the following coccicheck warning:
drivers/scsi/qedi/qedi_main.c:1309:5-25: WARNING: Comparison of 0/1 to
bool variable
drivers/scsi/qedi/qedi_main.c:1315:5-25: WARNING: Comparison of 0/1 to
bool variable
Zou Wei [Thu, 30 Apr 2020 10:02:12 +0000 (18:02 +0800)]
scsi: aacraid: Make some symbols static
Fix the following sparse warnings:
drivers/scsi/aacraid/linit.c:867:6: warning:
symbol 'aac_tmf_callback' was not declared. Should it be static?
drivers/scsi/aacraid/linit.c:1081:5: warning:
symbol 'aac_eh_host_reset' was not declared. Should it be static?
drivers/scsi/aacraid/commsup.c:2354:5: warning:
symbol 'aac_send_safw_hostttime' was not declared. Should it be static?
drivers/scsi/aacraid/commsup.c:2383:5: warning:
symbol 'aac_send_hosttime' was not declared. Should it be static?
Jason Yan [Wed, 6 May 2020 06:17:57 +0000 (14:17 +0800)]
scsi: qla2xxx: Make qlafx00_process_aen() return void
No other functions use the return value of qlafx00_process_aen() and the
return value is always 0 now. Make it return void. This fixes the following
coccicheck warning:
drivers/scsi/qla2xxx/qla_mr.c:1716:5-9: Unneeded variable: "rval".
Return "0" on line 1768
Jason Yan [Thu, 30 Apr 2020 12:17:51 +0000 (20:17 +0800)]
scsi: qla2xxx: Use true, false for need_mpi_reset
Fix the following coccicheck warning:
drivers/scsi/qla2xxx/qla_tmpl.c:1031:6-20: WARNING: Assignment of 0/1 to
bool variable
drivers/scsi/qla2xxx/qla_tmpl.c:1062:3-17: WARNING: Assignment of 0/1 to
bool variable
Jason Yan [Wed, 29 Apr 2020 14:09:52 +0000 (22:09 +0800)]
scsi: qla2xxx: Make qla_set_ini_mode() return void
The return value is not used by the caller and the local variable 'rc' is
not needed. Make qla_set_ini_mode() return void and remove 'rc'. This also
fixes the following coccicheck warning:
drivers/scsi/qla2xxx/qla_attr.c:1906:5-7: Unneeded variable: "rc".
Return "0" on line 2180
scsi: qla2xxx: Fix issue with adapter's stopping state
The goal of the following command sequence is to restart the adapter.
However, the tgt_stop flag remains set, indicating that the adapter is
still in stopping state even after re-enabling it.
qlt_handle_cmd_for_atio() rejects the request to send commands because the
adapter is in the stopping state:
kernel: PID 0:qla_target.c:4442 qlt_handle_cmd_for_atio(): tgt_stop 0x1, tgt_stopped 0x0
kernel: qla2xxx [0001:00:02.0]-3861:1: PID 0:qla_target.c:4447: New command while device c000000005314600 is shutting down
kernel: qla2xxx [0001:00:02.0]-e85f:1: PID 0:qla_target.c:5728: qla_target: Unable to send command to target
This patch calls qla_stop_phase2() in addition to qlt_stop_phase1() in
tcm_qla2xxx_tpg_enable_store() and tcm_qla2xxx_npiv_tpg_enable_store(). The
qlt_stop_phase1() marks adapter as stopping (tgt_stop == 0x1, tgt_stopped
== 0x0) but qlt_stop_phase2() marks adapter as stopped (tgt_stop == 0x0,
tgt_stopped == 0x1).
The reason of this message is the QLA_FUNCTION_FAILED code that
qla2x00_wait_for_hba_online() returns. However, qlt_disable_vha() expects
that adapter is offlined and QLA_FUNCTION_FAILED informs about the offline
state of the adapter.
The qla2x00_abort_isp() function finishes the execution at the point of
checking the adapter's mode (for example, qla_tgt_mode_enabled()) because
of the qlt_disable_vha() calls qlt_clear_mode() method. It means that
qla2x00_abort_isp() keeps vha->flags.online is equal to zero. Finally,
qla2x00_wait_for_hba_online() checks the state of this flag and returns
QLA_FUNCTION_FAILED error code.
This patch changes the failure message which informs about adapter's
offline state.
The issue happens because no real ISP reset is executed. The
qla2x00_abort_isp(scsi_qla_host_t *vha) function expects that
vha->flags.online will be not zero for ISP reset procedure. This patch
sets vha->flags.online to 1 before calling ->abort_isp() for starting the
ISP reset.
Damien Le Moal [Thu, 7 May 2020 02:35:26 +0000 (11:35 +0900)]
scsi: scsi_debug: Disallow zone sizes that are not powers of 2
Allowing a non-power-of-2 zone size forces the use of direct division
operations of 64-bit sector values to obtain a zone number or number of
zones. Doing so without using do_div() leads to compilation errors on
32-bit architectures.
Devices with a zone size that is not a power of 2 do not exist today so
allowing their emulation is of limited interest as the sd driver will not
support them anyway. To fix this compilation error, instead of using
do_div() for sector values divisions, simply disallow zone size values that
are not a power of 2.
[mkp: commit desc]
Link: https://lore.kernel.org/r/20200507023526.221574-1-damien.lemoal@wdc.com Fixes: 98e0a689868c ("scsi: scsi_debug: Add zone_size_mb module parameter") Fixes: f0d1cf9378bd ("scsi: scsi_debug: Add ZBC zone commands") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Implement ZBC host-aware device model emulation. The main changes from the
host-managed emulation are the device type (TYPE_DISK is used), relaxation
of access checks for read and write operations and different handling of a
sequential write preferred zone write pointer as mandated by the ZBC r05
specifications.
To facilitate the implementation and avoid a lot of "if" statement, the
zmodel field is added to the device information and the z_type field to the
zone state data structure.
Add the zone_size_mb module parameters to control the zone size of a ZBC
device. If the zone size specified is not a divisor of the device capacity,
the last zone of the device will be created as a smaller "runt" zone. This
parameter is ignored for device types other than 0x14 (zbc=2 case).
Note: for testing purposes, zone sizes that are not a power of 2 are
accepted but will result in the drive being rejected by the sd driver.
Allow controlling the number of conventional zones of a ZBC device with the
new zone_nr_conv module parameter. The default value is 1 and the specified
value must be less than the total number of zones of the device. This
parameter is ignored for device types other than 0x14 (zbc=2 case).
Add the zone_max_open module parameters to control the maximum number of
open zones of a ZBC device. This parameter is ignored for device types
other than 0x14 (zbc=2 case).
Douglas Gilbert [Wed, 22 Apr 2020 10:42:17 +0000 (19:42 +0900)]
scsi: scsi_debug: Add ZBC module parameter
Add the zbc module parameter to take either:
0: none (probably a conventional disk)
1: host-aware
2: host-managed
These values are chosen to match 'enum blk_zoned_model' found in
include/linux/blkdev.h . Instead of "none", "no" or "0" can be given.
Instead of "host-aware", "aware or "1" can be given. Instead of
"host-managed", "managed" or "2" can be given.
Note: the zbc parameter can only be given at driver/module load time; it
cannot be changed via sysfs thereafter.
At this time there is no ZBC "host-aware" implementation so that string (or
the value '1') results in a modprobe error.
projects / kernel.git / log