From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.
Fix it by checking whether the command is known before collecting the
failure data.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.
The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.
[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 0f0359b1e6d9 ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib") Signed-off-by: Erez Shitrit <erezsh@nvidia.com> Reviewed-by: Alex Vesker <valex@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Fixes: 84515d313736 ("mlx5: use page_pool for xdp_return_frame call") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0
Fixes: eab22a3adb09 ("net/mlx5e: Create new flow attr for multi table actions") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cited commit causes ABBA deadlock[0] when peer flows are created while
holding the devcom rw semaphore. Due to peer flows offload implementation
the lock is taken much higher up the call chain and there is no obvious way
to easily fix the deadlock. Instead, since tc route query code needs the
peer eswitch structure only to perform a lookup in xarray and doesn't
perform any sleeping operations with it, refactor the code for lockless
execution in following ways:
- RCUify the devcom 'data' pointer. When resetting the pointer
synchronously wait for RCU grace period before returning. This is fine
since devcom is currently only used for synchronization of
pairing/unpairing of eswitches which is rare and already expensive as-is.
- Wrap all usages of 'paired' boolean in {READ|WRITE}_ONCE(). The flag has
already been used in some unlocked contexts without proper
annotations (e.g. users of mlx5_devcom_is_paired() function), but it wasn't
an issue since all relevant code paths checked it again after obtaining the
devcom semaphore. Now it is also used by mlx5_devcom_get_peer_data_rcu() as
"best effort" check to return NULL when devcom is being unpaired. Note that
while RCU read lock doesn't prevent the unpaired flag from being changed
concurrently it still guarantees that reader can continue to use 'data'.
- Refactor mlx5e_tc_query_route_vport() function to use new
mlx5_devcom_get_peer_data_rcu() API which fixes the deadlock.
[0]:
[ 164.599612] ======================================================
[ 164.600142] WARNING: possible circular locking dependency detected
[ 164.600667] 6.3.0-rc3+ #1 Not tainted
[ 164.601021] ------------------------------------------------------
[ 164.601557] handler1/3456 is trying to acquire lock:
[ 164.601998] ffff88811f1714b0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}, at: mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[ 164.603078]
but task is already holding lock:
[ 164.603617] ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[ 164.604459]
which lock already depends on the new lock.
Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.
When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.
However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.
Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.
Fixes: 5e3eb404d3b9 ("sctp: do state transition when a probe succeeds on HB ACK recv path") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Memory_Info_Valid bit (CXL 3.0 8.1.3.8.2) indicates that the CXL
Range Size High and Size Low registers are valid. The bit must be set
within 1 second of reset deassertion to the device. Check valid bit
before we check the Memory_Active bit when waiting for
cxl_await_media_ready() to ensure that the memory info is valid for
consumption. Also ensures both DVSEC ranges 1 and 2 are ready if DVSEC
Capability indicates they are both supported.
Fixes: 348bfb5d34fc ("cxl/pci: Implement wait for media active") Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/168444687469.3134781.11033518965387297327.stgit@djiang5-mobl3 Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e40f514a7a37 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
Commit 77b242da0928 ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee70 ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
This worked before by coincidence, as the regulator was probed and enabled
before PCI RC probe. But probe order changed since commit 259b93b21a9f
("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in
4.14") and PCIe supply is enabled after RC.
Fix this by adding the regulator to RC node.
The PCIe vaux regulator still needs to be enabled unconditionally for
Mini-PCIe USB-only devices.
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot(). Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.
On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.
Fixes: 224721cd6819 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping") Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: 8219d5b2f768 ("VFS: Differentiate mount flags (MS_*) from internal superblock flags") Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags] Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e06f597b5307 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration") Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com> Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ffa_drv->remove() is called unconditionally from
ffa_device_remove(). Since the driver registration doesn't check for it
and allows it to be registered without .remove callback, we need to check
for the presence of it before executing it from ffa_device_remove() to
above a NULL pointer dereference like the one below:
Fixes an uninitialized variable in irq_handler() that could lead to
unpredictable behavior in case OP-TEE fails to handle SMC function ID
OPTEE_SMC_GET_ASYNC_NOTIF_VALUE. This change ensures that in that case
get_async_notif_value() properly reports there are no notification
event.
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 4844e773c5ee ("power: supply: bq24190_charger: Get input_current_limit from our supplier") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 2023dd163da2 ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol") Fixes: c79dce5ba4b5 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: dd2dd2078771 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 6a3839cb7d2b ("bq27x00: Cache battery registers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 16eab3aa731c ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 2ba575a761cd ("power: bq27xxx_battery: Add interrupt handling support") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: dd2dd2078771 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: a1c7f7f219bf ("power_supply: Add new LED trigger charging-blink-solid-full") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com> Fixes: 6c525ac49b92 ("cifs: switch to new mount api") Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: f57843b84709 ("[IPV6]: Find option offset by type.") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.
Fixes: 972d3be0c013 ("net: lan966x: add the basic lan966x driver") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails.
Fixes: e750e4c48365 ("bpf: Avoid hashtab deadlock with map_locked") Signed-off-by: Anton Protopopov <aspsk@isovalent.com> Link: https://lore.kernel.org/r/20230522154558.2166815-1-aspsk@isovalent.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.
In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
results in the following code generation for a 64-bit field:
HW adds segment size to the payload length
in the IPv6 header. Fix payload length to
just TCP header length instead of 'TCP header
size + IPv6 header size'.
Fixes: b82e703718f1 ("octeontx2-pf: TCP segmentation offload support") Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()
Tests passed: 201
Tests failed: 0
Cannot remove namespace file "/run/netns/ns1": No such file or directory
This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.
Redirect the error message to /dev/null to mute it.
V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2
Fixes: b60417a9f2b8 ("selftest: fib_tests: Always cleanup before exit") Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mutex_init() lockdep identifies a lock by defining a special static
key for each lock class. However if we wrap the macro in a function,
like in drmm_mutex_init(), we end up generating:
The static __key here is what lockdep uses to identify the lock class,
however since this is just a normal function the key here will be
created once, where all callers then use the same key. In effect the
mutex->depmap.key will be the same pointer for different
drmm_mutex_init() callers. This then results in impossible lockdep
splats since lockdep thinks completely unrelated locks are the same lock
class.
To fix this turn drmm_mutex_init() into a macro such that it generates a
different "static struct lock_class_key __key" for each invocation,
which looks to be inline with what mutex_init() wants.
v2:
- Revamp the commit message with clearer explanation of the issue.
- Rather export __drmm_mutex_release() than static inline.
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> Reported-by: Sarah Walker <sarah.walker@imgtec.com> Fixes: 9387d68d9157 ("drm: Add DRM-managed mutex_init()") Cc: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Jocelyn Falempe <jfalempe@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Matthew Auld <matthew.auld@intel.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230519090733.489019-1-matthew.auld@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
these endpoints (and similarly for the radio-shark driver).
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
the endpoints.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
syzbot reported [0] a null-ptr-deref in sk_get_rmem0() while using
IPPROTO_UDPLITE (0x88):
14:25:52 executing program 1:
r0 = socket$inet6(0xa, 0x80002, 0x88)
We had a similar report [1] for probably sk_memory_allocated_add()
in __sk_mem_raise_allocated(), and commit 095fa7ce76f9 ("udplite: fix
NULL pointer dereference") fixed it by setting .memory_allocated for
udplite_prot and udplitev6_prot.
To fix the variant, we need to set either .sysctl_wmem_offset or
.sysctl_rmem.
Now UDP and UDPLITE share the same value for .memory_allocated, so we
use the same .sysctl_wmem_offset for UDP and UDPLITE.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com Fixes: 8e74e15a285b ("net/core: generic support for disabling netdev features down stack") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation.
Since we may hold gic_lock in hardirq context, use raw spinlock
makes more sense given that it is for low-level interrupt handling
routine and the critical section is small.
When a GIC local interrupt is not routable, it's vl_map will be used
to control some internal states for core (providing IPTI, IPPCI, IPFDC
input signal for core). Overriding it will interfere core's intetrupt
controller.
Do not touch vl_map if a local interrupt is not routable, we are not
going to remap it.
Before e7f42ea11176 (" irqchip/mips-gic: Get rid of the reliance on
irq_cpu_online()"), if a local interrupt is not routable, then it won't
be requested from GIC Local domain, and thus gic_all_vpes_irq_cpu_online
won't be called for that particular interrupt.
Fixes: e7f42ea11176 (" irqchip/mips-gic: Get rid of the reliance on irq_cpu_online()") Cc: stable@vger.kernel.org Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230424103156.66753-2-jiaxun.yang@flygoat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.
Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.
smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.
Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.
On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.
Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21
Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:
-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1
This is also expected to make the scheduler do rather wonky things
too.
[ dhansen: remove CPUID detail from changelog, add end user effects ]
CC: stable@kernel.org Fixes: 197c15c68a0c ("x86: use cpuid vector 0xb when available for detecting cpu topology") Fixes: 1eabe5c2323d ("x86/cpu/topology: Provide detect_extended_topology_early()") Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of CHAs from the discovery table on some SPR variants is
incorrect, because of a firmware issue. An accurate number can be read
from the MSR UNC_CBO_CONFIG.
Fixes: 78044bd0e633 ("perf/x86/intel/uncore: Add Sapphire Rapids server CHA support") Reported-by: Stephane Eranian <eranian@google.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Stephane Eranian <eranian@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230508140206.283708-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardik Garg [Fri, 26 May 2023 23:21:36 +0000 (16:21 -0700)]
selftests/memfd: Fix unknown type name build failure
Partially backport v6.3 commit 11f75a01448f ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:
fuse_test.c:64:8: error: unknown type name '__u64'
64 | static __u64 mfd_assert_get_seals(int fd)
This header includes the __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.
[ cmllamas: clean forward port from commit 015ac18be7de ("binder: fix
UAF of alloc->vma in race with munmap()") in 5.10 stable. It is needed
in mainline after the revert of commit 6b4465651707 ("android: binder:
stop saving a pointer to the VMA") as pointed out by Liam. The commit
log and tags have been tweaked to reflect this. ]
In commit 58625b2a2b9b ("ANDROID: binder: change down_write to
down_read") binder assumed the mmap read lock is sufficient to protect
alloc->vma inside binder_update_page_range(). This used to be accurate
until commit 5dcd5782f466 ("mm: mmap: zap pages with read mmap_sem in
munmap"), which now downgrades the mmap_lock after detaching the vma
from the rbtree in munmap(). Then it proceeds to teardown and free the
vma with only the read lock held.
This means that accesses to alloc->vma in binder_update_page_range() now
will race with vm_area_free() in munmap() and can cause a UAF as shown
in the following KASAN trace:
==================================================================
BUG: KASAN: use-after-free in vm_insert_page+0x7c/0x1f0
Read of size 8 at addr ffff16204ad00600 by task server/558
To prevent the race above, revert back to taking the mmap write lock
inside binder_update_page_range(). One might expect an increase of mmap
lock contention. However, binder already serializes these calls via top
level alloc->mutex. Also, there was no performance impact shown when
running the binder benchmark tests.
Fixes: c0fd2101781e ("Revert "android: binder: stop saving a pointer to the VMA"") Fixes: 5dcd5782f466 ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Closes: https://lore.kernel.org/all/20230518144052.xkj6vmddccq4v66b@revolver Cc: <stable@vger.kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Yang Shi <yang.shi@linux.alibaba.com> Cc: Liam Howlett <liam.howlett@oracle.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20230519195950.1775656-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In binder_transaction_buffer_release() the 'failed_at' offset indicates
the number of objects to clean up. However, this function was changed by
commit a8da26fbba81 ("binder: use standard functions to allocate fds"),
to release all the objects in the buffer when 'failed_at' is zero.
This introduced an issue when a transaction buffer is released without
any objects having been processed so far. In this case, 'failed_at' is
indeed zero yet it is misinterpreted as releasing the entire buffer.
This leads to use-after-free errors where nodes are incorrectly freed
and subsequently accessed. Such is the case in the following KASAN
report:
==================================================================
BUG: KASAN: slab-use-after-free in binder_thread_read+0xc40/0x1f30
Read of size 8 at addr ffff4faf037cfc58 by task poc/474
In order to avoid these issues, let's always calculate the intended
'failed_at' offset beforehand. This is renamed and wrapped in a helper
function to make it clear and convenient.
Fixes: 8d03a8dadb9d ("binder: don't detect sender/target during buffer cleanup") Reported-by: Zi Fan Tan <zifantan@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Acked-by: Todd Kjos <tkjos@google.com> Link: https://lore.kernel.org/r/20230505203020.4101154-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bring back the original lockless design in binder_alloc to determine
whether the buffer setup has been completed by the ->mmap() handler.
However, this time use smp_load_acquire() and smp_store_release() to
wrap all the ordering in a single macro call.
Also, add comments to make it evident that binder uses alloc->vma to
determine when the binder_alloc has been fully initialized. In these
scenarios acquiring the mmap_lock is not required.
Fixes: 6b4465651707 ("android: binder: stop saving a pointer to the VMA") Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20230502201220.1756319-3-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed an issue reported by syzkaller in [1]. However, this
turned out to be only a band-aid in binder. The root cause, as bisected
by syzkaller, was fixed by commit 8c37e6862a52 ("mm/mmap: undo ->mmap()
when mas_preallocate() fails"). We no longer need the patch for binder.
Reverting such patch allows us to have a lockless access to alloc->vma
in specific cases where the mmap_lock is not required. This approach
avoids the contention that caused a performance regression.
This caused a performance regression particularly when pages are getting
reclaimed. We don't need to acquire the mmap_lock to determine when the
binder buffer has been fully initialized. A subsequent patch will bring
back the lockless approach for this.
[cmllamas: resolved trivial conflicts with renaming of alloc->mm]
Fixes: 1561d3aedb20 ("binder_alloc: add missing mmap_lock calls when using the VMA") Cc: Liam Howlett <liam.howlett@oracle.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: stable@vger.kernel.org Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20230502201220.1756319-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Printing the other clock types should not be conditioned on being able
to print OD_SCLK. Some GPUs currently have limited capability of only
printing a subset of these.
Since this condition was introduced in v5.18-rc1, reading from
`pp_od_clk_voltage` has been returning empty on the Asus ROG Strix G15
(2021).
Fixes: 0f365d4d7536 ("drm/amd/pm: do not expose power implementation details to amdgpu_pm.c") Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Jonatas Esteves <jntesteves@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, the power source switching will fail due to message
unavailable.
Fixes: bf4823267a81 ("drm/amd/pm: fix possible power mode mismatch between driver and PMFW") Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Guchun Chen <guchun.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put back the radeon_dp_work_func logic. It seems that
handling DP RX interrupts is necessary to make some
panels work. This was removed with the MST support,
but it regresses some systems so add it back. While
we are here, add the proper mutex locking.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2567 Fixes: 7a2196c21538 ("drm/radeon: Drop legacy MST support") Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mgag200 switched from simple KMS to regular atomic helpers,
the initialization of the gamma settings was lost.
This leads to a black screen, if the bios/uefi doesn't use the same
pixel color depth.
v2: rebase on top of drm-misc-fixes, and add Cc stable tag.
In cdns3-gadget.c, 'cdns,on-chip-buff-size' was read using
device_property_read_u16(). It resulted in 0 if a 32bit value was used
in dts. This commit fixes the dt binding doc to declare it as u16.
Cc: stable@vger.kernel.org Fixes: 969c17684a2f ("dt-bindings: usb: Convert cdns-usb3.txt to YAML schema") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have. The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here. Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's debugfs files have had a read operation since commit 4ed6199559fe ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
When patching the kernel code some alternatives depend on SMP vs. !SMP.
Use the value of num_present_cpus() instead of num_online_cpus() to
decide, otherwise we may run into issues if and additional CPU is
enabled after having loaded a module while only one CPU was enabled.
gcc-13 may generate calls for __bswap{si,di}2. This breaks the kernel
build when optimization for size is selected. Add __bswap{si,di}2
helpers to fix that.
Cc: stable@vger.kernel.org Fixes: d475bc924a19 ("xtensa: don't link with libgcc") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch function descriptor pointed to by the signal handler pointer from
userspace on signal delivery and function pointer pointed to by the
sa_restorer on return from the signal handler.
Cc: stable@vger.kernel.org Fixes: 72d4fd7a34e5 ("xtensa: add FDPIC and static PIE support for noMMU") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 204b69ec4bef9 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
The rt5682 driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 56.245502] rt5682 9-001a: ASoC: error at soc_component_read_no_lock on rt5682.9-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
This is essentially the same as commit f7d00a9be147 ("SoC:
rt5682s: Disable jack detection interrupt during suspend")
for the rt5682s.
Cc: stable@kernel.org Signed-off-by: Matthias Kaehlcke <mka@chromium.org Reviewed-by: Douglas Anderson <dianders@chromium.org Reviewed-by: Stephen Boyd <swboyd@chromium.org Link: https://lore.kernel.org/r/20230516164629.1.Ibf79e94b3442eecc0054d2b478779cc512d967fc@changeid Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where bq25890_charger_external_power_changed() may get called while
bq->charger has not been set yet leading to a NULL pointer dereference.
This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f
when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting
the connected charger-type which happens to exactly hit the small window:
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in bq->charger,
so bq25890_charger_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: c79dce5ba4b5 ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection") Cc: stable@vger.kernel.org Cc: Marek Vasut <marex@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where fuel_gauge_external_power_changed() may get called while
info->bat has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in info->bat,
so fuel_gauge_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
Fixes: 21156063f422 ("power: supply: axp288_fuel_gauge: Take lock before updating the valid flag") Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 8d62a092cb0e ("mmc: block: move single ioctl() commands to block requests") Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d9f11672422e ("mmc: sdhci-esdhc-imx: Propagate
ESDHC_FLAG_HS400* only on 8bit bus"), the property "no-mmc-hs400"
from device tree file do not work any more.
This patch reorder the code, which can avoid the warning message
"drop HS400 support since no 8-bit bus" and also make the property
"no-mmc-hs400" from dts file works.
Some calls to rpc_exit_task() may deliberately change the value of
task->tk_status, for instance because it gets checked by the RPC call's
rpc_release() callback. That makes it wrong to reset the value to
task->tk_rpc_status.
In particular this causes a bug where the rpc_call_done() callback tries
to fail over a set of pNFS/flexfiles writes to a different IP address,
but the reset of task->tk_status causes nfs_commit_release_pages() to
immediately mark the file as having a fatal error.
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
It's reported that the recording started right after the driver probe
doesn't work properly, and it turned out that this is related with the
codec auto-suspend. Namely, after the probe phase, the usage count
goes zero, and the auto-suspend is programmed, but the codec is kept
still active until the auto-suspend expiration. When an application
(e.g. alsactl) updates the mixer values at this moment, the values are
cached but not actually written. Then, starting arecord thereafter
also results in the silence because of the missing unmute.
The root cause is the handling of "lazy update" mode; when a mixer
value is updated *after* the suspend, it should update only the cache
and exits. At the resume, the cached value is written to the device,
in turn. The problem is that the current code misinterprets the state
of auto-suspend as if it were already suspended.
Although we can add the check of the actual device state after
pm_runtime_get_if_in_use() for catching the missing state, this won't
suffice; the second call of regmap_update_bits_check() will skip
writing the register because the cache has been already updated by the
first call. So we'd need fixes in two different places.
OTOH, a simpler fix is to replace pm_runtime_get_if_in_use() with
pm_runtime_get_if_active() (with ign_usage_count=true). This change
implies that the driver takes the pm refcount if the device is still
in ACTIVE state and continues the processing. A small caveat is that
this will leave the auto-suspend timer. But, since the timer callback
itself checks the device state and aborts gracefully when it's active,
this won't be any substantial problem.
Long story short: we address the missing register-write problem just
by replacing the pm_runtime_*() call in snd_hda_keep_power_up().
Correct this by calling INIT_WORK_ONSTACK instead of INIT_WORK.
Fixes: 1313cd120acc ("platform/x86/intel/ifs: Authenticate and copy to secured memory") Signed-off-by: David Arcari <darcari@redhat.com> Cc: Jithu Joseph <jithu.joseph@intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230523105400.674152-1-darcari@redhat.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)
Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.
As a workaround, never enable PCIDs on affected processors.
I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.
Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) A page in a PROT_READ|PROT_WRITE VMA is faulted.
2) Page migration allocates a page with the KASAN allocator,
causing it to receive a non-match-all tag, and uses it
to replace the page faulted in 1.
3) The program uses mprotect() to enable PROT_MTE on the page faulted in 1.
As a result of step 3, we are left with a non-match-all tag for a page
with tags accessible to userspace, which can lead to the same kind of
tag check faults that commit e74a68468062 ("arm64: Reset KASAN tag in
copy_highpage with HW tags only") intended to fix.
The general invariant that we have for pages in a VMA with VM_MTE_ALLOWED
is that they cannot have a non-match-all tag. As a result of step 2, the
invariant is broken. This means that the fix in the referenced commit
was incomplete and we also need to reset the tag for pages without
PG_mte_tagged.
In preparation for removing security_old_inode_init_security(), switch to
security_inode_init_security().
Extend the existing ocfs2_initxattrs() to take the
ocfs2_security_xattr_info structure from fs_info, and populate the
name/value/len triple with the first xattr provided by LSMs.
As fs_info was not used before, ocfs2_initxattrs() can now handle the case
of replicating the behavior of security_old_inode_init_security(), i.e.
just obtaining the xattr, in addition to setting all xattrs provided by
LSMs.
Supporting multiple xattrs is not currently supported where
security_old_inode_init_security() was called (mknod, symlink), as it
requires non-trivial changes that can be done at a later time. Like for
reiserfs, even if EVM is invoked, it will not provide an xattr (if it is
not the first to set it, its xattr will be discarded; if it is the first,
it does not have xattrs to calculate the HMAC on).
Finally, since security_inode_init_security(), unlike
security_old_inode_init_security(), returns zero instead of -EOPNOTSUPP if
no xattrs were provided by LSMs or if inodes are private, additionally
check in ocfs2_init_security_get() if the xattr name is set.
If not, act as if security_old_inode_init_security() returned -EOPNOTSUPP,
and set si->enable to zero to notify to the functions following
ocfs2_init_security_get() that no xattrs are available.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Reviewed-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reviewed-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
This is the fix for the defect of commit 7da9694efabd
("drm/amd/display: Allow individual control of eDP hotplug support").
[How]
To revise the default eDP hotplug setting and use the enum to git rid
of the magic number for different options.
Fixes: 7da9694efabd ("drm/amd/display: Allow individual control of eDP hotplug support") Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eeefe7c4820b6baa0462a8b723ea0a3b5846ccae)
Hand modified for missing file rename changes and symbol moves in 6.1.y. Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / kernel.git / log