This patch updates the PTE flags when translate further (TF) is
enabled:
- With translate_further enabled, invalid PTEs can be 0. Reading
consecutive invalid PTEs as 0 is considered a fault. To prevent
this, ensure invalid PTEs have at least 1 bit set.
- The current invalid PTE flags settings to translate a retry fault
into a no-retry fault, doesn't work with TF enabled. As a result,
update invalid PTE flags settings which works for both TF enabled
and disabled case.
Fixes: 352e683b72e79d ("drm/amdgpu: Enable translate_further to extend UTCL2 reach") Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Mukul Joshi <mukul.joshi@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yifan Zhang [Tue, 30 Aug 2022 15:18:47 +0000 (23:18 +0800)]
drm/amdgpu/mes: zero the sdma_hqd_mask of 2nd SDMA engine for SDMA 6.0.1
there is only one SDMA engine in SDMA 6.0.1, the sdma_hqd_mask has to be
zeroed for the 2nd engine, otherwise MES scheduler will consider 2nd
engine exists and map/unmap SDMA queues to the non-existent engine.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: Tim Huang <Tim.Huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 30 Aug 2022 14:59:49 +0000 (10:59 -0400)]
drm/amdgpu: make sure to init common IP before gmc
Move common IP init before GMC init so that HDP gets
remapped before GMC init which uses it.
This fixes the Unsupported Request error reported through
AER during driver load. The error happens as a write happens
to the remap offset before real remapping is done.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216373
The error was unnoticed before and got visible because of the commit
referenced below. This doesn't fix anything in the commit below, rather
fixes the issue in amdgpu exposed by the commit. The reference is only
to associate this commit with below one so that both go together.
Fixes: 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()") Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Alex Deucher [Fri, 9 Sep 2022 15:53:27 +0000 (11:53 -0400)]
drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega
This mirrors what we do for other asics and this way we are
sure the sdma doorbell range is properly initialized.
There is a comment about the way doorbells on gfx9 work that
requires that they are initialized for other IPs before GFX
is initialized. However, the statement says that it applies to
multimedia as well, but the VCN code currently initializes
doorbells after GFX and there are no known issues there. In my
testing at least I don't see any problems on SDMA.
This is a prerequisite for fixing the Unsupported Request error
reported through AER during driver load.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216373
The error was unnoticed before and got visible because of the commit
referenced below. This doesn't fix anything in the commit below, rather
fixes the issue in amdgpu exposed by the commit. The reference is only
to associate this commit with below one so that both go together.
Fixes: 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()") Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Alex Deucher [Fri, 9 Sep 2022 15:47:20 +0000 (11:47 -0400)]
drm/amdgpu: move nbio ih_doorbell_range() into ih code for vega
This mirrors what we do for other asics and this way we are
sure the ih doorbell range is properly initialized.
There is a comment about the way doorbells on gfx9 work that
requires that they are initialized for other IPs before GFX
is initialized. In this case IH is initialized before GFX,
so there should be no issue.
This is a prerequisite for fixing the Unsupported Request error
reported through AER during driver load.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216373
The error was unnoticed before and got visible because of the commit
referenced below. This doesn't fix anything in the commit below, rather
fixes the issue in amdgpu exposed by the commit. The reference is only
to associate this commit with below one so that both go together.
Fixes: 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()") Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Commit a0f7e7f759cf ("drm/amd/display: fix i386 frame size warning")
aimed to address this for i386 but it did not help x86_64.
To reduce the amount of stack space that
dml30_ModeSupportAndSystemConfigurationFull() uses, mark
UseMinimumDCFCLK() as noinline, using the _for_stack variant for
documentation. While this will increase the total amount of stack usage
between the two functions (1632 and 1304 bytes respectively), it will
make sure both stay below the limit of 2048 bytes for these files. The
aforementioned change does help reduce UseMinimumDCFCLK()'s stack usage
so it should not be reverted in favor of this change.
drm/amd/display: Reduce number of arguments of dml31's CalculateFlipSchedule()
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml31_ModeSupportAndSystemConfigurationFull() uses by 112 bytes with
LLVM 16 (1976 -> 1864), helping clear up the following clang warning:
drm/amd/display: Reduce number of arguments of dml31's CalculateWatermarksAndDRAMSpeedChangeSupport()
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml31_ModeSupportAndSystemConfigurationFull() uses by 240 bytes with
LLVM 16 (2216 -> 1976), helping clear up the following clang warning:
drm/amd/display: Reduce number of arguments of dml32_CalculatePrefetchSchedule()
Several of the arguments are identical between the two call sites and
they can be accessed through the 'struct vba_vars_st' pointer. This
reduces the total amount of stack space that
dml32_ModeSupportAndSystemConfigurationFull() uses by 208 bytes with
LLVM 16 (1936 -> 1728), helping clear up the following clang warning:
drm/amd/display: Reduce number of arguments of dml32_CalculateWatermarksMALLUseAndDRAMSpeedChangeSupport()
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer created at the
top of dml32_ModeSupportAndSystemConfigurationFull(). This reduces the
total amount of stack space that
dml32_ModeSupportAndSystemConfigurationFull() uses by 216 bytes with
LLVM 16 (2152 -> 1936), helping clear up the following clang warning:
Additionally, while modifying the arguments to
dml32_CalculateWatermarksMALLUseAndDRAMSpeedChangeSupport(), use 'v'
consistently, instead of 'v' mixed with 'mode_lib->vba'.
Alvin Lee [Fri, 5 Aug 2022 17:58:00 +0000 (01:58 +0800)]
drm/amd/display: Refactor SubVP calculation to remove FPU
Refactor calculation to remove floating point operations from dmub_srv.
To ensure that 32-bit compilation works well, we use the div64 family of
macros to do integer division for SubVP-related timing parameters.
Cc: Maíra Canal <mairacanal@riseup.net> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Isabella Basso <isabbasso@riseup.net> Cc: Magali Lemes <magalilemes00@gmail.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Samson Tam <Samson.Tam@amd.com> Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Co-developed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yao Wang1 [Mon, 22 Aug 2022 10:30:31 +0000 (18:30 +0800)]
drm/amd/display: Limit user regamma to a valid value
[Why]
For HDR mode, we get total 512 tf_point and after switching to SDR mode
we actually get 400 tf_point and the rest of points(401~512) still use
dirty value from HDR mode. We should limit the rest of the points to max
value.
[How]
Limit the value when coordinates_x.x > 1, just like what we do in
translate_from_linear_space for other re-gamma build paths.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Yao Wang1 <Yao.Wang1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aurabindo Pillai [Thu, 25 Aug 2022 19:05:58 +0000 (15:05 -0400)]
drm/amd/display: add workaround for subvp cursor corruption for DCN32/321
[Why&How]
Kernel does not have a means to tell the userspace to use software
cursor. Due to lack of this functionality, reducing the max cursor size
is the only way to ensure that power savings of Subview port feature is
utilized for asics that support it. The workaround could be removed
after cursor caching is fixed while a subviewport config is active.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Wed, 24 Aug 2022 15:53:50 +0000 (11:53 -0400)]
drm/amd/display: SW cursor fallback for SubVP
[Description]
Leverage SW cursor fall back for SubVP when the cursor is too big. We
want to take advantage of being able to fallback to SW cursor when
possible because it's not worth it to disable MCLK switching because the
cursor is slightly too big.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Taimur Hassan [Thu, 25 Aug 2022 16:33:12 +0000 (12:33 -0400)]
drm/amd/display: Round cursor width up for MALL allocation
[Why & How]
When calculating cursor size for MALL allocation, the cursor width should
be the actual width rounded up to 64 alignment. Additionally, the bit
depth should vary depending on color format.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Duncan Ma [Wed, 24 Aug 2022 18:35:03 +0000 (14:35 -0400)]
drm/amd/display: Correct dram channel width for dcn314
[Why]
The interpretation of the number of memory channels
differ by memory type, and this affects channel width
for the DML input.
[How]
Set dram channel width according to memory type for
dcn314.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Duncan Ma <duncan.ma@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Relax swizzle checks for video non-RGB formats on DCN314
[Why]
HW can support the display swizzle modes for video, and those are
preferable over standard or linear for decode use.
[How]
Remove the check for DCN314.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Hook up DCN314 specific dml implementation
[Why & How]
Add support for the DML314 functions and hook up DCN314 to use them.
This has some necessary additions for calculating Max VSTARTUP for
future features, but there's also some changes that we have to make
for pixel format/swizzle support.
That will come in a following patch to make this transition easier to
bisect.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Enable dlg and vba compilation for dcn314
We were not using the VBA and DLG files for DCN314, but the next
sequence of changes for DCN314 will require those files. This commit
adds the necessary files to the Makefile.
Cc: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have some compilation errors in some DML files from DCN314 that we
never noticed because we were not compiling some of the DML files. This
commit fixes those syntax errors before we enable the compilation.
Cc: Roman Li <roman.li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aric Cyr [Wed, 24 Aug 2022 20:34:53 +0000 (16:34 -0400)]
drm/amd/display: Fix divide by zero in DML
[why]
Incorrectly using MicroTileWidth instead of MacroTileWidth for
calculations.
[how]
Remove all unused references to MicroTile and change them to MacroTile.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Aric Cyr <aric.cyr@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leo Chen [Wed, 24 Aug 2022 19:34:24 +0000 (15:34 -0400)]
drm/amd/display: Fixing DIG FIFO Error
[Why & How]
DIG_FIFO_READ_START_LEVEL should only be set to default value (7) by software.
Removed all instances of resetting the register to 0
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Leo Chen <sancchen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alvin Lee [Tue, 23 Aug 2022 21:14:03 +0000 (17:14 -0400)]
drm/amd/display: Update MBLK calculation for SubVP
[Description]
Update MBLK calculation according to hardware doc. For DCC case we were
not allocation enough MALL due to an inaccurate MBLK calculation.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aurabindo Pillai [Thu, 11 Aug 2022 20:42:12 +0000 (16:42 -0400)]
drm/amd/display: Revert "Fallback to SW cursor if SubVP + cursor too big"
This reverts commit a4f1b04216023ff0f4cd89328b59ee6890248130 since
returning false in case of SubVP results in no cursor being visible on
desktop as there is no sw cursor fallback path on all platforms.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 30 Aug 2022 15:08:09 +0000 (11:08 -0400)]
drm/amdgpu: add HDP remap functionality to nbio 7.7
Was missing before and would have resulted in a write to
a non-existant register. Normally APUs don't use HDP, but
other asics could use this code and APUs do use the HDP
when used in passthrough.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yang Wang [Fri, 9 Sep 2022 03:06:50 +0000 (11:06 +0800)]
drm/amdgpu: change the alignment size of TMR BO to 1M
align TMR BO size TO tmr size is not necessary,
modify the size to 1M to avoid re-create BO fail
when serious VRAM fragmentation.
v2:
add new macro PSP_TMR_ALIGNMENT for TMR BO alignment size
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hamza Mahfooz [Tue, 6 Sep 2022 19:01:49 +0000 (15:01 -0400)]
drm/amdgpu: use dirty framebuffer helper
Currently, we aren't handling DRM_IOCTL_MODE_DIRTYFB. So, use
drm_atomic_helper_dirtyfb() as the dirty callback in the amdgpu_fb_funcs
struct.
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As per PCIE Base Spec r4.0 Section 6.18
'Software must not enable LTR in an Endpoint unless the Root Complex
and all intermediate Switches indicate support for LTR.'
This fixes the Unsupported Request error reported through AER during
ASPM enablement.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216455
The error was unnoticed before and got visible because of the commit
referenced below. This doesn't fix anything in the commit below, rather
fixes the issue in amdgpu exposed by the commit. The reference is only
to associate this commit with below one so that both go together.
Fixes: 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()") Reported-by: Gustaw Smolarczyk <wielkiegie@gmail.com> Signed-off-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/panfrost: devfreq: set opp to the recommended one to configure regulator
Enabling panfrost GPU OPP with dynamic regulator will make OPP
responsible to enable and configure it.
Unfortunately OPP configure and enable the regulator when an OPP
is asked to be set, which is not the case during
panfrost_devfreq_init().
This leave the regulator unconfigured and if no GPU load is
triggered, no OPP is asked to be set which make the regulator framework
switching it off during regulator_late_cleanup() without
noticing and therefore make the board hang as any access to GPU
memory space make bus locks up.
Call dev_pm_opp_set_opp() with the recommend OPP in
panfrost_devfreq_init() to enable the regulator, this will properly
configure and enable the regulator and will avoid any switch off
by regulator_late_cleanup().
drm/amdgpu: correct doorbell range/size value for CSDMA_DOORBELL_RANGE
current function mixes CSDMA_DOORBELL_RANGE and SDMA0_DOORBELL_RANGE
range/size manipulation, while these 2 registers have difference size
field mask. Remove range/size manipulation for SDMA0_DOORBELL_RANGE.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: Xiaojian Du <Xiaojian.Du@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: fix memory leak when using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. Fix this up by properly
calling dput().
Cc: Harry Wentland <harry.wentland@amd.com> Cc: Leo Li <sunpeng.li@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: "Christian König" <christian.koenig@amd.com> Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: hersen wu <hersenxs.wu@amd.com> Cc: Wenjing Liu <wenjing.liu@amd.com> Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Cc: Thelford Williams <tdwilliamsiv@gmail.com> Cc: Fangzhi Zuo <Jerry.Zuo@amd.com> Cc: Yongzhi Liu <lyz_cs@pku.edu.cn> Cc: Mikita Lipski <mikita.lipski@amd.com> Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Cc: Bhanuprakash Modem <bhanuprakash.modem@intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: amd-gfx@lists.freedesktop.org Cc: dri-devel@lists.freedesktop.org Cc: stable@vger.kernel.org Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Matthew Auld [Mon, 5 Sep 2022 10:53:29 +0000 (11:53 +0100)]
drm/i915: consider HAS_FLAT_CCS() in needs_ccs_pages
Just move the HAS_FLAT_CCS() check into needs_ccs_pages. This also then
fixes i915_ttm_memcpy_allowed() which was incorrectly reporting true on
DG1, even though it doesn't have small-BAR or flat-CCS.
Ville Syrjälä [Fri, 2 Sep 2022 07:03:18 +0000 (10:03 +0300)]
drm/i915: Implement WaEdpLinkRateDataReload
A lot of modern laptops use the Parade PS8461E MUX for eDP
switching. The MUX can operate in jitter cleaning mode or
redriver mode, the first one resulting in higher link
quality. The jitter cleaning mode needs to know the link
rate used and the MUX achieves this by snooping the
LINK_BW_SET, LINK_RATE_SELECT and SUPPORTED_LINK_RATES
DPCD accesses.
When the MUX is powered down (seems this can happen whenever
the display is turned off) it loses track of the snooped
link rates so when we do the LINK_RATE_SELECT write it no
longer knowns which link rate we're selecting, and thus it
falls back to the lower quality redriver mode. This results
in unstable high link rates (eg. usually 8.1Gbps link rate
no longer works correctly).
In order to avoid all that let's re-snoop SUPPORTED_LINK_RATES
from the sink at the start of every link training.
Unfortunately we don't have a way to detect the presence of
the MUX. It looks like the set of laptops equipped with this
MUX is fairly large and contains devices from multiple
manufacturers. It may also still be growing with new models.
So a quirk doesn't seem like a very easily maintainable
option, thus we shall attempt to do this unconditionally on
all machines that use LINK_RATE_SELECT. Hopefully this extra
DPCD read doesn't cause issues for any unaffected machine.
If that turns out to be the case we'll need to convert this
into a quirk in the future.
Cc: stable@vger.kernel.org Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6205 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220902070319.15395-1-ville.syrjala@linux.intel.com Tested-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 25899c590cb5ba9b9f284c6ca8e7e9086793d641) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rodrigo Vivi [Wed, 31 Aug 2022 21:45:38 +0000 (17:45 -0400)]
drm/i915/slpc: Let's fix the PCODE min freq table setup for SLPC
We need to inform PCODE of a desired ring frequencies so PCODE update
the memory frequencies to us. rps->min_freq and rps->max_freq are the
frequencies used in that request. However they were unset when SLPC was
enabled and PCODE never updated the memory freq.
v2 (as Suggested by Ashutosh): if SLPC is in use, let's pick the right
frequencies from the get_ia_constants instead of the fake init of
rps' min and max.
v3: don't forget the max <= min return
v4: Move all the freq conversion to intel_rps.c. And the max <= min
check to where it belongs.
v5: (Ashutosh) Fix old comment s/50 HZ/50 MHz and add a doc explaining
the "raw format"
Fixes: 7ba79a671568 ("drm/i915/guc/slpc: Gate Host RPS when SLPC is enabled") Cc: <stable@vger.kernel.org> # v5.15+ Cc: Ashutosh Dixit <ashutosh.dixit@intel.com> Tested-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220831214538.143950-1-rodrigo.vivi@intel.com
(cherry picked from commit 018a7bdbb090b9155a6509a0d1a684db4afaa5b1) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Ville Syrjälä [Mon, 29 Aug 2022 13:58:34 +0000 (16:58 +0300)]
drm/i915/bios: Copy the whole MIPI sequence block
Turns out the MIPI sequence block version number and
new block size fields are considered part of the block
header and are not included in the reported new block size
field itself. Bump up the block size appropriately so that
we'll copy over the last five bytes of the block as well.
For this particular machine those last five bytes included
parts of the GPIO op for the backlight on sequence, causing
the backlight no longer to turn back on:
Sequence 6 - MIPI_SEQ_BACKLIGHT_ON
Delay: 20000 us
- GPIO index 0, number 0, set 0 (0x00)
+ GPIO index 1, number 70, set 1 (0x01)
[Why]
Ghost BO is released with non-empty bulk move object. There is a
warning trace:
WARNING: CPU: 19 PID: 1582 at ttm/ttm_bo.c:366 ttm_bo_release+0x2e1/0x2f0 [amdttm]
Call Trace:
amddma_resv_reserve_fences+0x10d/0x1f0 [amdkcl]
amdttm_bo_put+0x28/0x30 [amdttm]
amdttm_bo_move_accel_cleanup+0x126/0x200 [amdttm]
amdgpu_bo_move+0x1a8/0x770 [amdgpu]
ttm_bo_handle_move_mem+0xb0/0x140 [amdttm]
amdttm_bo_validate+0xbf/0x100 [amdttm]
[How]
The resource of ghost BO should be moved to LRU directly, instead of
using bulk move. The bulk move object of ghost BO should set to NULL
before function ttm_bo_move_to_lru_tail_unlocked.
v2: set bulk move to NULL manually if no resource associated with ghost BO
Merge tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix handling of PCI domains in /proc on 32-bit systems using the
recently added support for numbering buses from zero for each domain.
- A fix and a revert for some changes to use READ/WRITE_ONCE() which
caused problems with KASAN enabled due to sanitisation calls being
introduced in low-level paths that can't cope with it.
- Fix build errors on 32-bit caused by the syscall table being
misaligned sometimes.
- Two fixes to get IBM Cell native machines booting again, which had
bit-rotted while my QS22 was temporarily out of action.
- Fix the papr_scm driver to not assume the order of events returned by
the hypervisor is stable, and a related compile fix.
Thanks to Aneesh Kumar K.V, Christophe Leroy, Jordan Niethe, Kajol Jain,
Masahiro Yamada, Nathan Chancellor, Pali Rohár, Vaibhav Jain, and Zhouyi
Zhou.
* tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
Revert "powerpc/irq: Don't open code irq_soft_mask helpers"
powerpc: Fix hard_irq_disable() with sanitizer
powerpc/rtas: Fix RTAS MSR[HV] handling for Cell
Revert "powerpc: Remove unused FW_FEATURE_NATIVE references"
powerpc: align syscall table for ppc32
powerpc/pci: Enable PCI domains in /proc when PCI bus numbers are not unique
powerpc/papr_scm: Fix nvdimm event mappings
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"s390:
- PCI interpretation compile fixes
RISC-V:
- fix unused variable warnings in vcpu_timer.c
- move extern sbi_ext declarations to a header
x86:
- check validity of argument to KVM_SET_MP_STATE
- use guest's global_ctrl to completely disable guest PEBS
- fix a memory leak on memory allocation failure
- mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
- fix build failure with Clang integrated assembler
- fix MSR interception
- always flush TLBs when enabling dirty logging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check validity of argument to KVM_SET_MP_STATE
perf/x86/core: Completely disable guest PEBS via guest's global_ctrl
KVM: x86: fix memoryleak in kvm_arch_vcpu_create()
KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
KVM: s390: pci: Hook to access KVM lowlevel from VFIO
riscv: kvm: move extern sbi_ext declarations to a header
riscv: kvm: vcpu_timer: fix unused variable warnings
KVM: selftests: Fix ambiguous mov in KVM_ASM_SAFE()
KVM: selftests: Fix KVM_EXCEPTION_MAGIC build with Clang
KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
kvm: x86: mmu: Always flush TLBs when enabling dirty logging
kvm: x86: mmu: Drop the need_remote_flush() function
Makefile.extrawarn: re-enable -Wformat for clang; take 2
-Wformat was recently re-enabled for builds with clang, then quickly
re-disabled, due to concerns stemming from the frequency of default
argument promotion related warning instances.
commit 258fafcd0683 ("Makefile.extrawarn: re-enable -Wformat for clang")
commit 21f9c8a13bb2 ("Revert "Makefile.extrawarn: re-enable -Wformat for clang"")
ISO WG14 has ratified N2562 to address default argument promotion
explicitly for printf, as part of the upcoming ISO C2X standard.
The behavior of clang was changed in clang-16 to not warn for the cited
cases in all language modes.
Add a version check, so that users of clang-16 now get the full effect
of -Wformat. For older clang versions, re-enable flags under the
-Wformat group that way users still get some useful checks related to
format strings, without noisy default argument promotion warnings. I
intentionally omitted -Wformat-y2k and -Wformat-security from being
re-enabled, which are also part of -Wformat in clang-16.
Merge tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A a set of fixes from the GPIO subsystem.
Most are small driver fixes except the realtek-otto driver patch which
is pretty big but addresses a significant flaw that can cause the CPU
to stay infinitely busy on uncleared ISR on some platforms.
Summary:
- MAINTAINERS update
- fix resource leaks in gpio-mockup and gpio-pxa
- add missing locking in gpio-pca953x
- use 32-bit I/O in gpio-realtek-otto
- make irq_chip structures immutable in four more drivers"
* tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ws16c48: Make irq_chip immutable
gpio: 104-idio-16: Make irq_chip immutable
gpio: 104-idi-48: Make irq_chip immutable
gpio: 104-dio-48e: Make irq_chip immutable
gpio: realtek-otto: switch to 32-bit I/O
gpio: pca953x: Add mutex_lock for regcache sync in PM
gpio: mockup: remove gpio debugfs when remove device
gpio: pxa: use devres for the clock struct
MAINTAINERS: rectify entry for XILINX GPIO DRIVER
Merge tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a minor fix for the Xen grant driver
- a small series fixing a recently introduced problem in the Xen
blkfront/blkback drivers with negotiation of feature usage
* tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
xen-blkfront: Cache feature_persistent value before advertisement
xen-blkfront: Advertise feature-persistent as user requested
xen-blkback: Advertise feature-persistent as user requested
Merge tag 'loongarch-fixes-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors or warnings, cleanup some code, and adjust
arch_do_signal_or_restart() to adapt generic entry"
* tag 'loongarch-fixes-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: mm: Remove the unneeded result variable
LoongArch: Fix arch_remove_memory() undefined build error
LoongArch: Fix section mismatch due to acpi_os_ioremap()
LoongArch: Improve dump_tlb() output messages
LoongArch: Adjust arch_do_signal_or_restart() to adapt generic entry
LoongArch: Avoid orphan input sections
Merge tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
* tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add support for Boeder Force Feedback Wheel
Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
Input: goodix - add compatible string for GT1158
MAINTAINERS: add include/dt-bindings/input to INPUT DRIVERS
Input: rk805-pwrkey - fix module autoloading
Input: goodix - add support for GT1158
dt-bindings: input: touchscreen: add compatible string for Goodix GT1158
Merge tag 'tty-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial/vt driver fixes for 6.0-rc4 that
resolve a number of reported issues:
- n_gsm fixups for previous changes that caused problems
- much-reported serdev crash fix that showed up in 6.0-rc1
- vt font selection bugfix
- kerneldoc build warning fixes
- other tiny serial core fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: n_gsm: avoid call of sleeping functions from atomic context
tty: n_gsm: replace kicktimer with delayed_work
tty: n_gsm: initialize more members at gsm_alloc_mux()
tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
tty: serial: atmel: Preserve previous USART mode if RS485 disabled
tty: serial: lpuart: disable flow control while waiting for the transmit engine to complete
tty: Fix lookahead_buf crash with serdev
serial: fsl_lpuart: RS485 RTS polariy is inverse
vt: Clear selection before changing the font
serial: document start_rx member at struct uart_ops
Merge tag 'staging-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three small staging driver fixes for 6.0-rc4 that resolve
some reported problems and add some a device id:
- new device id for r8188eu driver
- use-after-free bugfixes for the rtl8712 driver
- fix up firmware dependency problem for the r8188eu driver
All of these have been in linux-next for a while with no reported
problems"
* tag 'staging-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix use after free bugs
staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
staging: r8188eu: add firmware dependency
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's a collection of primarily clk driver fixes, with a couple fixes
to the core framework.
We had to revert out a commit that affected boot on some devices that
have the CLK_OPS_PARENT_ENABLE flag set. It isn't critical to have
that fix so we'll try again next time.
Driver side fixes include:
- Plug an OF-node refcount bug in the TI clk driver
- Fix the error handling in the raspberry pi firmware get_rate so
that errors don't look like valid frequencies
- Avoid going out of bounds in the raspberry pi driver too if the
video firmware returns something we're not expecting"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
clk: bcm: rpi: Show clock id limit in error case
clk: bcm: rpi: Add missing newline
clk: bcm: rpi: Prevent out-of-bounds access
clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
clk: core: Fix runtime PM sequence in clk_core_unprepare()
clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
clk: ti: Fix missing of_node_get() ti_find_clock_provider()
Merge tag 'hwmon-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix out of bounds access in gpio-fan driver
- Fix VOUT margin caching in PMBus core
- Avoid error message after -EPROBE_DEFER from devm_regulator_register()
* tag 'hwmon-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Fix array out of bounds access
hwmon: (pmbus) Fix vout margin caching
hwmon: (pmbus) Use dev_err_probe() to filter -EPROBE_DEFER error messages
Steven Price [Fri, 2 Sep 2022 11:26:12 +0000 (12:26 +0100)]
mm: pagewalk: Fix race between unmap and page walker
The mmap lock protects the page walker from changes to the page tables
during the walk. However a read lock is insufficient to protect those
areas which don't have a VMA as munmap() detaches the VMAs before
downgrading to a read lock and actually tearing down PTEs/page tables.
For users of walk_page_range() the solution is to simply call pte_hole()
immediately without checking the actual page tables when a VMA is not
present. We now never call __walk_page_range() without a valid vma.
For walk_page_range_novma() the locking requirements are tightened to
require the mmap write lock to be taken, and then walking the pgd
directly with 'no_vma' set.
This in turn means that all page walkers either have a valid vma, or
it's that special 'novma' case for page table debugging. As a result,
all the odd '(!walk->vma && !walk->no_vma)' tests can be removed.
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Steven Price <steven.price@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LoongArch: Fix section mismatch due to acpi_os_ioremap()
Now acpi_os_ioremap() is marked with __init because it calls memblock_
is_memory() which is also marked with __init in the !ARCH_KEEP_MEMBLOCK
case. However, acpi_os_ioremap() is called by ordinary functions such
as acpi_os_{read, write}_memory() and causes section mismatch warnings:
Fix these warnings by selecting ARCH_KEEP_MEMBLOCK unconditionally and
removing the __init modifier of acpi_os_ioremap(). This can also give a
chance to track "memory" and "reserved" memblocks after early boot.
Huacai Chen [Wed, 31 Aug 2022 03:19:27 +0000 (11:19 +0800)]
LoongArch: Adjust arch_do_signal_or_restart() to adapt generic entry
Commit 8ba62d37949e248c69 ("task_work: Call tracehook_notify_signal from
get_signal on all architectures") adjust arch_do_signal_or_restart() for
all architectures. LoongArch hasn't been upstream yet at that time and
can be still built successfully without adjustment because this function
has a weak version with the correct prototype. It is obviously that we
should convert LoongArch to use new API, otherwise some signal handlings
will be lost.
Ard Biesheuvel [Wed, 24 Aug 2022 15:31:10 +0000 (17:31 +0200)]
LoongArch: Avoid orphan input sections
Ensure that all input sections are listed explicitly in the linker
script, and issue a warning otherwise. This ensures that the binary
image matches the PE/COFF and other image metadata exactly, which is
important for things like code signing.
Merge tag 'block-6.0-2022-09-02' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- error handling fix for the new auth code (Hannes Reinecke)
- fix unhandled tcp states in nvmet_tcp_state_change (Maurizio
Lombardi)
- add NVME_QUIRK_BOGUS_NID for Lexar NM610 (Shyamin Ayesh)
- Add documentation for the ublk driver merged in this merge window
(Ming)
* tag 'block-6.0-2022-09-02' of git://git.kernel.dk/linux-block:
Documentation: document ublk
nvmet-tcp: fix unhandled tcp states in nvmet_tcp_state_change()
nvmet-auth: add missing goto in nvmet_setup_auth()
nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM610
Merge tag 'io_uring-6.0-2022-09-02' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- A single fix for over-eager retries for networking (Pavel)
- Revert the notification slot support for zerocopy sends.
It turns out that even after more than a year or development and
testing, there's not full agreement on whether just using plain
ordered notifications is Good Enough to avoid the complexity of using
the notifications slots. Because of that, we decided that it's best
left to a future final decision.
We can always bring back this feature, but we can't really change it
or remove it once we've released 6.0 with it enabled. The reverts
leave the usual CQE notifications as the primary interface for
knowing when data was sent, and when it was acked. (Pavel)
* tag 'io_uring-6.0-2022-09-02' of git://git.kernel.dk/linux-block:
selftests/net: return back io_uring zc send tests
io_uring/net: simplify zerocopy send user API
io_uring/notif: remove notif registration
Revert "io_uring: rename IORING_OP_FILES_UPDATE"
Revert "io_uring: add zc notification flush requests"
selftests/net: temporarily disable io_uring zc test
io_uring/net: fix overexcessive retries
Merge tag '6.0-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five fixes, all also marked for stable:
- fixes for collapse range and insert range (also fixes xfstest
generic/031)
- memory leak fix"
* tag '6.0-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix small mempool leak in SMB2_negotiate()
smb3: use filemap_write_and_wait_range instead of filemap_write_and_wait
smb3: fix temporary data corruption in insert range
smb3: fix temporary data corruption in collapse range
smb3: Move the flush out of smb2_copychunk_range() into its callers
Merge tag 'landlock-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux
Pull landlock fix from Mickaël Salaün:
"This fixes a mis-handling of the LANDLOCK_ACCESS_FS_REFER right when
multiple rulesets/domains are stacked.
The expected behaviour was that an additional ruleset can only
restrict the set of permitted operations, but in this particular case,
it was potentially possible to re-gain the LANDLOCK_ACCESS_FS_REFER
right"
* tag 'landlock-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Fix file reparenting without explicit LANDLOCK_ACCESS_FS_REFER
Merge tag 'drm-fixes-2022-09-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull. One core dma-buf fix, then two weeks of i915
fixes, a lot of amdgpu fixes mostly for new IP, and a bunch of msm
fixes, mostly modesetting ones.
Nothing seems too bad at this point.
dma-buf/dma-resv:
- Fence-handling fix
i915:
- GVT fixes including fix for a CommetLake regression in mmio table
and misc doc and typo fixes
- Fix CCS handling
- Fix for guc requests after reset
- Display DSI related fixes
- Display backlight related fixes
- Fix for a null pointer dereference
- HDMI related quirk for ECS Liva Q2 with GLK graphics
- Skip wm/ddb readout for disabled pipes
amdgpu:
- FRU error message fix
- MES 11 updates
- DCN 3.2.x fixes
- DCN 3.1.4 fixes
- Fix possible use after free in CS IOCTL
- SMU 13.0.x fixes
- Fix iolink reporting on devices with direct connections to CPU
- GFX10 tap delay firmware fixes
msm:
- Fix for inconsistent indenting in msm_dsi_dphy_timing_calc_v3().
- Fix to make eDP the first connector in the connected list.
- Fix to populate intf_cfg correctly before calling reset_intf_cfg().
- Specify the correct number of DSI regulators for SDM660.
- Specify the correct number of DSI regulators for MSM8996.
- Fix for removing DP_RECOVERED_CLOCK_OUT_EN bit for tps4 link training
- Fix probe-deferral crash in gpu devfreq
- Fix gpu debugfs deadlock"
* tag 'drm-fixes-2022-09-02' of git://anongit.freedesktop.org/drm/drm: (51 commits)
drm/amd/amdgpu: skip ucode loading if ucode_size == 0
drm/amdgpu: only init tap_delay ucode when it's included in ucode binary
drm/amd/display: Fix black flash when switching from ODM2to1 to ODMBypass
drm/amd/display: Fix check for stream and plane
drm/amd/display: Re-initialize viewport after pipe merge
drm/amd/display: Use correct plane for CAB cursor size allocation
drm/amdgpu: ensure no PCIe peer access for CPU XGMI iolinks
drm/amd/pm: bump SMU 13.0.0 driver_if header version
drm/amd/pm: use vbios carried pptable for all SMU13.0.7 SKUs
drm/amd/pm: use vbios carried pptable for those supported SKUs
drm/amd/display: fix wrong register access
drm/amd/display: use actual cursor size instead of max for CAB allocation
drm/amd/display: disable display fresh from MALL on an edge case for DCN321
drm/amd/display: Fix CAB cursor size allocation for DCN32/321
drm/amd/display: Missing HPO instance added
drm/amd/display: set dig fifo read start level to 7 before dig fifo reset
drm/amdgpu: Fix use-after-free in amdgpu_cs_ioctl
drm/amd/display: Fix OTG H timing reset for dcn314
drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programming
drm/amdgpu: Update mes_v11_api_def.h
...
Merge tag 'char-misc-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc and other driver fixes for 6.0-rc4.
Included in here are:
- binder fixes for previous fixes, and a few more fixes uncovered by
them.
- iio driver fixes
- soundwire driver fixes
- fastrpc driver fixes for memory corruption on some hardware
- peci driver fix
- mhi driver fix
All of these have been in linux-next with no reported problems"
* tag 'char-misc-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix alloc->vma_vm_mm null-ptr dereference
misc: fastrpc: increase maximum session count
misc: fastrpc: fix memory corruption on open
misc: fastrpc: fix memory corruption on probe
soundwire: qcom: fix device status array range
bus: mhi: host: Fix up null pointer access in mhi_irq_handler
soundwire: qcom: remove duplicate reset control get
iio: light: cm32181: make cm32181_pm_ops static
iio: ad7292: Prevent regulator double disable
dt-bindings: iio: gyroscope: bosch,bmg160: correct number of pins
iio: adc: mcp3911: use correct formula for AD conversion
iio: adc: mcp3911: correct "microchip,device-addr" property
Revert "binder_alloc: Add missing mmap_lock calls when using the VMA"
binder_alloc: Add missing mmap_lock calls when using the VMA
binder: fix UAF of ref->proc caused by race condition
iio: light: cm3605: Fix an error handling path in cm3605_probe()
iio: adc: mcp3911: make use of the sign bit
peci: cpu: Fix use-after-free in adev_release()
peci: aspeed: fix error check return value of platform_get_irq()
Merge tag 'usb-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt driver fixes from Greg KH:
"Here are a lot of small USB and Thunderbolt driver fixes for 6.0-rc4
for reported problems. Included in here are:
- new usb-serial driver ids
- dwc3 driver bugfixes for reported problems with 6.0-rc1
- new device quirks, and reverts of some quirks that were incorrect
- gadget driver bugfixes for reported problems
- USB host controller bugfixes (xhci and others)
- other small USB fixes, details in the shortlog
- small thunderbolt driver fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (51 commits)
Revert "usb: gadget: udc-xilinx: replace memcpy with memcpy_toio"
usb: storage: Add ASUS <0x0b05:0x1932> to IGNORE_UAS
USB: serial: ch341: fix disabled rx timer on older devices
USB: serial: ch341: fix lost character on LCR updates
USB: serial: cp210x: add Decagon UCA device id
Revert "usb: add quirks for Lenovo OneLink+ Dock"
usb: cdns3: fix issue with rearming ISO OUT endpoint
usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transfer
usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OS
media: mceusb: Use new usb_control_msg_*() routines
USB: core: Prevent nested device-reset calls
USB: gadget: Fix obscure lockdep violation for udc_mutex
usb: dwc2: fix wrong order of phy_power_on and phy_init
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: typec: Remove retimers properly
usb: dwc3: disable USB core PHY management
usb: add quirks for Lenovo OneLink+ Dock
USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
USB: serial: option: add Quectel EM060K modem
...
Merge tag 'platform-drivers-x86-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Various small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: p2sb: Fix UAF when caller uses resource name
platform/x86: asus-wmi: Increase FAN_CURVE_BUF_LEN to 32
platform/mellanox: Remove redundant 'NULL' check
platform/mellanox: Remove unnecessary code
platform/mellanox: mlxreg-lc: Fix locking issue
platform/mellanox: mlxreg-lc: Fix coverity warning
platform/x86: acer-wmi: Acer Aspire One AOD270/Packard Bell Dot keymap fixes
platform/x86: thinkpad_acpi: Explicitly set to balanced mode on startup
platform/x86: asus-wmi: Fix the name of the mic-mute LED classdev
platform/surface: aggregator_registry: Add HID devices for sensors and UCSI client to SP8
platform/surface: aggregator_registry: Rename HID device nodes based on new findings
platform/surface: aggregator_registry: Rename HID device nodes based on their function
platform/surface: aggregator_registry: Add support for Surface Laptop Go 2
platform/x86: x86-android-tablets: Fix broken touchscreen on Chuwi Hi8 with Windows BIOS
platform/x86: pmc_atom: Fix SLP_TYPx bitfield mask
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's a lot smaller than last week, with the star of the show being a
couple of fixes to head.S addressing a boot regression introduced by
the recent overhaul of that code in non-default configurations (i.e.
KASLR disabled).
The first of those two resolves the issue reported (and bisected) by
Mikulus in the wait_on_bit() thread.
Summary:
- Fix two boot issues caused by the recent head.S rework when !KASLR
- Fix calculation of crashkernel memory reservation
- Fix bogus error check in PMU IRQ probing code"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Reserve enough pages for the initial ID map
perf/arm_pmu_platform: fix tests for platform_get_irq() failure
arm64: head: Ignore bogus KASLR displacement on non-relocatable kernels
arm64/kexec: Fix missing extra range for crashkres_low.
Ville Syrjälä [Fri, 26 Aug 2022 21:34:51 +0000 (00:34 +0300)]
drm/edid: Handle EDID 1.4 range descriptor h/vfreq offsets
EDID 1.4 introduced some extra flags in the range
descriptor to support min/max h/vfreq >= 255. Consult them
to correctly parse the vfreq limits.
Note that some combinations of the flags are documented
as "reserved" (as are some other values in the descriptor)
but explicitly checking for those doesn't seem particularly
worthwile since we end up with bogus results whether we
decode them or not.
v2: Increase the storage to u16 to make it work (Jani)
Note the "reserved" values situation (Jani)
v3: Document the EDID version number in the defines
Drop some bogus (u8) casts
Cc: stable@vger.kernel.org Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6519
References: https://gitlab.freedesktop.org/drm/intel/-/issues/6484 Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220826213501.31490-2-ville.syrjala@linux.intel.com Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Mickaël Salaün [Wed, 31 Aug 2022 20:38:40 +0000 (22:38 +0200)]
landlock: Fix file reparenting without explicit LANDLOCK_ACCESS_FS_REFER
This change fixes a mis-handling of the LANDLOCK_ACCESS_FS_REFER right
when multiple rulesets/domains are stacked. The expected behaviour was
that an additional ruleset can only restrict the set of permitted
operations, but in this particular case, it was potentially possible to
re-gain the LANDLOCK_ACCESS_FS_REFER right.
With the introduction of LANDLOCK_ACCESS_FS_REFER, we added the first
globally denied-by-default access right. Indeed, this lifted an initial
Landlock limitation to rename and link files, which was initially always
denied when the source or the destination were different directories.
This led to an inconsistent backward compatibility behavior which was
only taken into account if no domain layer were using the new
LANDLOCK_ACCESS_FS_REFER right. However, when restricting a thread with
a new ruleset handling LANDLOCK_ACCESS_FS_REFER, all inherited parent
rulesets/layers not explicitly handling LANDLOCK_ACCESS_FS_REFER would
behave as if they were handling this access right and with all their
rules allowing it. This means that renaming and linking files could
became allowed by these parent layers, but all the other required
accesses must also be granted: all layers must allow file removal or
creation, and renaming and linking operations cannot lead to privilege
escalation according to the Landlock policy. See detailed explanation
in commit b91c3e4ea756 ("landlock: Add support for file reparenting with
LANDLOCK_ACCESS_FS_REFER").
To say it another way, this bug may lift the renaming and linking
limitations of the initial Landlock version, and a same ruleset can
enforce different restrictions depending on previous or next enforced
ruleset (i.e. inconsistent behavior). The LANDLOCK_ACCESS_FS_REFER right
cannot give access to data not already allowed, but this doesn't follow
the contract of the first Landlock ABI. This fix puts back the
limitation for sandboxes that didn't opt-in for this additional right.
For instance, if a first ruleset allows LANDLOCK_ACCESS_FS_MAKE_REG on
/dst and LANDLOCK_ACCESS_FS_REMOVE_FILE on /src, renaming /src/file to
/dst/file is denied. However, without this fix, stacking a new ruleset
which allows LANDLOCK_ACCESS_FS_REFER on / would now permit the
sandboxed thread to rename /src/file to /dst/file .
This change fixes the (absolute) rule access rights, which now always
forbid LANDLOCK_ACCESS_FS_REFER except when it is explicitly allowed
when creating a rule.
Making all domain handle LANDLOCK_ACCESS_FS_REFER was an initial
approach but there is two downsides:
* it makes the code more complex because we still want to check that a
rule allowing LANDLOCK_ACCESS_FS_REFER is legitimate according to the
ruleset's handled access rights (i.e. ABI v1 != ABI v2);
* it would not allow to identify if the user created a ruleset
explicitly handling LANDLOCK_ACCESS_FS_REFER or not, which will be an
issue to audit Landlock.
Instead, this change adds an ACCESS_INITIALLY_DENIED list of
denied-by-default rights, which (only) contains
LANDLOCK_ACCESS_FS_REFER. All domains are treated as if they are also
handling this list, but without modifying their fs_access_masks field.
A side effect is that the errno code returned by rename(2) or link(2)
*may* be changed from EXDEV to EACCES according to the enforced
restrictions. Indeed, we now have the mechanic to identify if an access
is denied because of a required right (e.g. LANDLOCK_ACCESS_FS_MAKE_REG,
LANDLOCK_ACCESS_FS_REMOVE_FILE) or if it is denied because of missing
LANDLOCK_ACCESS_FS_REFER rights. This may result in different errno
codes than for the initial Landlock version, but this approach is more
consistent and better for rename/link compatibility reasons, and it
wasn't possible before (hence no backport to ABI v1). The
layout1.rename_file test reflects this change.
Add 4 layout1.refer_denied_by_default* test suites to check that the
behavior of a ruleset not handling LANDLOCK_ACCESS_FS_REFER (ABI v1) is
unchanged even if another layer handles LANDLOCK_ACCESS_FS_REFER (i.e.
ABI v1 precedence). Make sure rule's absolute access rights are correct
by testing with and without a matching path. Add test_rename() and
test_exchange() helpers.
Extend layout1.inval tests to check that a denied-by-default access
right is not necessarily part of a domain's handled access rights.
Test coverage for security/landlock is 95.3% of 599 lines according to
gcc/gcov-11.
Fixes: b91c3e4ea756 ("landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER") Reviewed-by: Paul Moore <paul@paul-moore.com> Reviewed-by: Günther Noack <gnoack3000@gmail.com> Link: https://lore.kernel.org/r/20220831203840.1370732-1-mic@digikod.net Cc: stable@vger.kernel.org
[mic: Constify and slightly simplify test helpers] Signed-off-by: Mickaël Salaün <mic@digikod.net>
Dan Carpenter [Thu, 1 Sep 2022 15:35:20 +0000 (18:35 +0300)]
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
The change from kcalloc() to kvmalloc() means that arg->nr_pages
might now be large enough that the "args->nr_pages << PAGE_SHIFT" can
result in an integer overflow.
Fixes: b3f7931f5c61 ("xen/gntdev: switch from kcalloc() to kvcalloc()") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/YxDROJqu/RPvR0bi@kili Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:24 +0000 (16:58 +0000)]
xen-blkfront: Cache feature_persistent value before advertisement
Xen blkfront advertises its support of the persistent grants feature
when it first setting up and when resuming in 'talk_to_blkback()'.
Then, blkback reads the advertised value when it connects with blkfront
and decides if it will use the persistent grants feature or not, and
advertises its decision to blkfront. Blkfront reads the blkback's
decision and it also makes the decision for the use of the feature.
Commit 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter
when connect"), however, made the blkfront's read of the parameter for
disabling the advertisement, namely 'feature_persistent', to be done
when it negotiate, not when advertise. Therefore blkfront advertises
without reading the parameter. As the field for caching the parameter
value is zero-initialized, it always advertises as the feature is
disabled, so that the persistent grants feature becomes always disabled.
This commit fixes the issue by making the blkfront does parmeter caching
just before the advertisement.
Fixes: 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter when connect") Cc: <stable@vger.kernel.org> # 5.10.x Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-4-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:23 +0000 (16:58 +0000)]
xen-blkfront: Advertise feature-persistent as user requested
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent
grants") made a field of blkfront, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkfront saves
the parameter value in a separate place and advertises the support based
on only the saved value.
Fixes: 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-3-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:22 +0000 (16:58 +0000)]
xen-blkback: Advertise feature-persistent as user requested
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent
grants") made a field of blkback, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkback saves the
parameter value in a separate place and advertises the support based on
only the saved value.
Fixes: aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-2-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com>
powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
Clang warns:
arch/powerpc/platforms/pseries/papr_scm.c:492:6: warning: variable 'rc' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!p->stat_buffer_len)
^~~~~~~~~~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:523:64: note: uninitialized use occurs here
dev_info(&p->pdev->dev, "nvdimm pmu didn't register rc=%d\n", rc);
^~
include/linux/dev_printk.h:150:67: note: expanded from macro 'dev_info'
dev_printk_index_wrap(_dev_info, KERN_INFO, dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:492:2: note: remove the 'if' if its condition is always false
if (!p->stat_buffer_len)
^~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:484:8: note: initialize the variable 'rc' to silence this warning
int rc, nodeid;
^
= 0
1 warning generated.
The call to papr_scm_pmu_check_events() was eliminated but a return code
was not added to the if statement. Add the same return code from
papr_scm_pmu_check_events() for this condition so there is no more
warning.
If there is a context switch before "stb r9,2354(r31)", r31 may
not equal to r13, in such case, irq soft mask will not work.
The usual solution of marking the code ineligible for instrumentation
forces the code out-of-line, which we would prefer to avoid. Christophe
proposed a partial revert, but Nick raised some concerns with that. So
for now do a full revert.
Merge tag 'soundwire-6.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
"soundwire fixes for v6.0
This contains two fixes to qcom sdw driver which resolve duplicate reset
control get and second one fixes device array indices."
* tag 'soundwire-6.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: qcom: fix device status array range
soundwire: qcom: remove duplicate reset control get
Dave Airlie [Fri, 2 Sep 2022 01:26:29 +0000 (11:26 +1000)]
Merge tag 'drm-intel-fixes-2022-09-01' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for a null pointer dereference (Lukasz)
- HDMI related quirk for ECS Liva Q2 with GLK graphics (Diego)
- Skip wm/ddb readout for disabled pipes (Ville)
Paolo Bonzini [Thu, 11 Aug 2022 16:41:25 +0000 (12:41 -0400)]
KVM: x86: check validity of argument to KVM_SET_MP_STATE
An invalid argument to KVM_SET_MP_STATE has no effect other than making the
vCPU fail to run at the next KVM_RUN. Since it is extremely unlikely that
any userspace is relying on it, fail with -EINVAL just like for other
architectures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like Xu [Wed, 31 Aug 2022 03:35:24 +0000 (11:35 +0800)]
perf/x86/core: Completely disable guest PEBS via guest's global_ctrl
When a guest PEBS counter is cross-mapped by a host counter, software
will remove the corresponding bit in the arr[global_ctrl].guest and
expect hardware to perform a change of state "from enable to disable"
via the msr_slot[] switch during the vmx transaction.
The real world is that if user adjust the counter overflow value small
enough, it still opens a tiny race window for the previously PEBS-enabled
counter to write cross-mapped PEBS records into the guest's PEBS buffer,
when arr[global_ctrl].guest has been prioritised (switch_msr_special stuff)
to switch into the enabled state, while the arr[pebs_enable].guest has not.
Close this window by clearing invalid bits in the arr[global_ctrl].guest.
Cc: linux-perf-users@vger.kernel.org Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sean Christopherson <seanjc@google.com> Fixes: 854250329c02 ("KVM: x86/pmu: Disable guest PEBS temporarily in two rare situations") Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220831033524.58561-1-likexu@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Miaohe Lin [Thu, 1 Sep 2022 12:23:00 +0000 (20:23 +0800)]
KVM: x86: fix memoryleak in kvm_arch_vcpu_create()
When allocating memory for mci_ctl2_banks fails, KVM doesn't release
mce_banks leading to memoryleak. Fix this issue by calling kfree()
for it when kcalloc() fails.
Fixes: 281b52780b57 ("KVM: x86: Add emulation for MSR_IA32_MCx_CTL2 MSRs.") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Message-Id: <20220901122300.22298-1-linmiaohe@huawei.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jim Mattson [Tue, 30 Aug 2022 17:49:47 +0000 (10:49 -0700)]
KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
KVM should not claim to virtualize unknown IA32_ARCH_CAPABILITIES
bits. When kvm_get_arch_capabilities() was originally written, there
were only a few bits defined in this MSR, and KVM could virtualize all
of them. However, over the years, several bits have been defined that
KVM cannot just blindly pass through to the guest without additional
work (such as virtualizing an MSR promised by the
IA32_ARCH_CAPABILITES feature bit).
Define a mask of supported IA32_ARCH_CAPABILITIES bits, and mask off
any other bits that are set in the hardware MSR.
Cc: Paolo Bonzini <pbonzini@redhat.com> Fixes: 5b76a3cff011 ("KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Vipin Sharma <vipinsh@google.com> Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20220830174947.2182144-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
projects / kernel.git / log