efi_loader: disk: allow blk devices even without UCLASS_PARTITION
While GPT partition is mandated in UEFI specification, CONFIG_PARTITION is
seen optional under the current implementation.
So modify efi_disk_rw_blocks() to allow accepting UCLASS_BLK devices.
Fixes: commit 5ab1ab597483 ("efi_loader: disk: use udevice instead of blk_desc") Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Mark Kettenis <kettenis@openbsd.org>
Tom Rini [Tue, 26 Apr 2022 11:54:12 +0000 (07:54 -0400)]
Merge tag 'u-boot-at91-2022.07-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the AT91 reset controller,
a new board called sam9x60 curiosity, and several other fixes and
clean-ups (sama7g5ek qspi clock, impedance; remove unused code,
introduce Kconfig symbols for SPL timers)
pci: fsl: Change compatible string for mpc8548 to "fsl, mpc8548-pcie"
Upstream Linux kernel uses for mpc8548-based PCIe controllers compatible
string "fsl,mpc8548-pcie". So change U-Boot fsl PCIe driver and all DTS
files to use "fsl,mpc8548-pcie" instead of "fsl,pcie-mpc8548" to be
compatible with Linux kernel.
powerpc: dts: p2020: Make usb@22000 node compatible for Linux kernel driver
Linux P2020 USB kernel driver uses compatible string fsl-usb2-dr-v1.6 and
needs more DT properties. Copy P2020 usb@22000 properties from upstream
Linux kernel.
powerpc: dts: p2020: Do not automatically disable spi@7000 node in p2020-post.dtsi
Device tree include file p2020-post.dtsi should be included after the board
device tree file and overrides settings of the board. So it should not
disable some node as board cannot enable it via normal way (it has to
enable it after inclusion of p2020-post.dtsi file).
Fix it by removal of explicit disable in p2020-post.dtsi file and then
remove explicit post-post enable in all P2020 board device tree files.
Currently no P2020 board has spi@7000 node disabled.
powerpc: dts: p2020: Add Linux compatible string and property for eSDHC
Linux kernel eSDHC driver for P2020 requires additional compatible string
fsl,p2020-esdhc and interrupts property. Add them to p2020-post.dtsi file
to make U-Boot board DTS files compatible for Linux kernel.
powerpc: dts: p2020: Add ptp_clock@24e00 node via pq3-etsec1-timer-0.dtsi
Import pq3-etsec1-timer-0.dtsi device tree include file from upstream Linux
kernel for P2020. This allows U-Boot to use P2020 device tree files from
upstream Linux kernel which reference ptp_clock@24e00 device.
powerpc: dts: p2020: Make PCIe nodes compatible for Linux kernel driver
Linux P2020 PCIe kernel driver uses compatible string fsl,mpc8548-pcie and
needs more DT properties. Copy P2020 PCIe nodes and definitions from
upstream Linux kernel.
powerpc: dts: p2020: Add gpio-controller@fc00 node via pq3-gpio-0.dtsi
Import pq3-gpio-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference gpio-controller@fc00 device.
Do not stringify env $vscfw_addr two times (once implicitly via string
operator "" and second time explicitly via __stringify() macro) and allow
to compile U-Boot without CONFIG_VSC7385_ENET (when __VSCFW_ADDR was not
defined and so macro name was stringified into CONFIG_EXTRA_ENV_SETTINGS).
board: freescale: p1_p2_rdb_pc: Fix page attributes for second 1G SDRAM map
Like for first 1G SDRAM map, do not enable Caching-inhibited nor Guarded
attribute for second 1G SDRAM mapping. Whole 2G SDRAM should use caches and
also allow speculative loading (by not setting Guarded attribute).
Also enable Memory Coherency attribute for second 1G SDRAM map. In commit 5fe1ab62495c ("powerpc: mpc85xx: Fix static TLB table for SDRAM") it was
enabled for all SDRAM maps on all other boards, just missed this one case.
As a last thing, first 1G SDRAM map has wrong comment, so adjust it.
Currently CONFIG_OF_SEPARATE is completely broken and U-Boot for some
mpc85xx board (e.g. P2020) has to be compiled with CONFIG_OF_EMBED.
Otherwise it crashes during early init.
When debug console is enabled and all debug logging options are turned on
then U-Boot on P2020 with CONFIG_OF_SEPARATE prints following error:
No valid device tree binary found at 110dc300
initcall sequence 110d3560 failed at call 1109535c (err=-1)
### ERROR ### Please RESET the board ###
Problem is with appended DTB. When CONFIG_SYS_MPC85XX_NO_RESETVEC is set
U-Boot binary image without DTB ends immediately after the .u_boot_list
section. At this position is defined _end symbol at which U-Boot expects
start of the appended DTB.
Problem is that after .u_boot_list section are in linker script defined
another sections with 256 byte long padding which are completely empty.
During conversion of U-Boot ELF binary to RAW binary u-boot-nodtb.bin,
objcopy removes trailing zero padding and therefore DTB is appended at
wrong position.
Changing alignment from 256 bytes to 4 bytes fixes this issue. And appended
DTB is finally at he correct position. With this fix U-Boot on P2020 with
CONFIG_OF_SEPARATE option starts working again.
For compatibility with Linux kernel DTS files and also with other U-Boot
powerpc DTS files, rename esdhc@2e000 node to sdhc@2e000 in p1020-post.dtsi
and p2020-post.dtsi include files.
Linux kernel DTS files which include these dtsi files, expect that esdhc
node has name sdhc@2e000 and do not work with other node names.
mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support
QorIQ pre-PBL BootROM scans first 24 SD card sectors (each with fixed 512
bytes length) for boot signature. Implement same redundancy behavior in
fsl_esdhc_spl driver to allow loading proper U-Boot when boot sector is not
the first one.
mtd: rawnand: fsl_elbc: Use ECC configuration from device tree
Initialize ECC configuration after nand_scan_ident() call and only in case
nand_scan_ident() have not done it. nand_scan_ident() fills ECC
configuration from device tree.
Fixes usage of NAND_ECC_SOFT_BCH when it is specified in device tree.
powerpc: dts: p2020: Add serial0 and serial1 via pq3-duart-0.dtsi
Import pq3-duart-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference serial0 or serial1 devices.
powerpc: dts: p2020: Add fsl/p2020si-pre.dtsi and fsl/p2020si-post.dtsi symlinks
P2020 DTS files in upstream Linux kernel use fsl/p2020si-pre.dtsi and
fsl/p2020si-post.dtsi include device tree files.
Add symlinks for these include device tree files into U-Boot powerpc
directory and points them to U-Boot inline device tree files p2020.dtsi and
p2020-post.dtsi.
This allows to use P2020 DTS files from upstream Linux kernel in U-Boot.
board: freescale: p1_p2_rdb_pc: Allow to compile it without env support
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
When env support is disabled then usage of env_get_f() generates linker
errors. So do not compile env_get_f() when env support is disabled (for
example when disabled only in SPL).
When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
mmc: mmc_mode_name() is used also when LOGLEVEL >= LOGL_DEBUG
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.
Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.
So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.
mmc: fsl_esdhc_spl: pre-PBL: check for BOOT signature instead of MBR/DBR
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.
So add check for BOOT signature and remove check for MBR/DBR.
This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.
powerpc: mpc85xx: Rename _start_e500 symbol to _start
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Stephen Carlson [Tue, 29 Mar 2022 21:51:10 +0000 (14:51 -0700)]
armv8/fsl-lsch3: Suppress spurious warning on Layerscape CPUs
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 22 Apr 2022 09:23:27 +0000 (14:53 +0530)]
armv8: layerscape: get rid of smc_call()
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 28 Feb 2022 12:48:37 +0000 (13:48 +0100)]
armv8: include psci_update_dt() unconditionally
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sean Anderson [Fri, 22 Apr 2022 08:31:36 +0000 (14:01 +0530)]
arm: layerscape: Disable erratum A009007 on LS1021A, LS1043A, and LS1046A
This erratum is reported to cause problems on these processors [1-3].
The problem is usually with the clocking, which is supposed to be
configured by the RCW [4]. However, if it is not set, or if the default
clocking is not correct, then this erratum will cause an SError.
However, according to Ran Wang in [1]:
" ... this erratum is used to pass USB compliance test only, you could
disable this workaround on your board if you don't any USB issue on
normal use case, I think it's fine."
So just disable this erratum by default for these processors.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
The impedance of the QSPI PCB lines on the sama7g5ek is 50 Ohms.
Align the output impedance of the QSPI0 HSIOs by setting a medium drive
strength which corresponds to an impedance of 56 Ohms when VDD is in the
3.0V - 3.6V range. The high drive strength setting corresponds to an
output impedance of 42 Ohms on the QSPI0 HSIOs.
This is just a fine tunning. The memory that we have populated on sama7g5ek
works fine even with high drive strength, but it's better to adjust it and
use medium instead, in case some other flashes with higher frequencies are
tested.
Suggested-by: Mihai Sain <mihai.sain@microchip.com> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This commit allows the ATMEL_PIT_TIMER driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 0.3 KBytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Eugen Hristev [Mon, 4 Apr 2022 08:35:50 +0000 (11:35 +0300)]
timers: atmel_tcb: introduce CONFIG_SPL_ATMEL_TCB
This commit allows the ATMEL_TCB driver to be unselected in SPL and be
selected in u-boot proper. The SPL can use a different timer.
By having a separate Kconfig for ATMEL_TCB in SPL, the size of the SPL
decreases by 1 KByte.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
binman: ./tools/binman/binman:12: DeprecationWarning:
The distutils package is deprecated and slated for removal in Python 3.12.
Use setuptools or check PEP 632 for potential alternatives
from distutils.sysconfig import get_python_lib
./tools/binman/binman:12: DeprecationWarning:
The distutils.sysconfig module is deprecated, use sysconfig instead
from distutils.sysconfig import get_python_lib
<unittest.result.TestResult run=428 errors=0 failures=4>
AssertionError: 0 != 468
As we don't use Ubuntu 16.04 for our CI anymore drop the import.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
I ended up learning most of binman internals while trying to add a few
features to it, and I recently started reviewing binman series that
would not affect me personally. I'll keep working on it and try to do
more reviews.
Add myself as a maintainer for binman.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Acked-by: Tom Rini <trini@konsulko.com>
Binman interfaces allow attempts to replace any entry in the image with
arbitrary data. When trying to replace sections, the changes in the
section entry's data are not propagated to its child entries. This,
combined with how sections rebuild their contents from its children,
eventually causes the replaced contents to be silently overwritten by
rebuilt contents equivalent to the original data.
Add a simple test for replacing a section that is currently failing due
to this behaviour, and mark it as an expected failure. Also, raise an
error when replacing a section instead of silently pretending it was
replaced.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Test replacing non-section entries in FIT subsections
A previous patch fixes binman to correctly extract FIT subentries. This
makes it easier to test replacing these entries as we can write tests
using an existing helper function that relies on extracting the replaced
entry.
Add tests that replace leaf entries in FIT subsections with data of
various sizes. Replacing the subsections or the whole FIT section does
not work yet due to the section contents being re-built from unreplaced
subentries' data.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Create FIT subentries in the FIT section, not its parent
When reading images from a file, each entry's data is read from its
parent section as specified in the Entry.Create() call that created it.
The FIT entry type has been creating its subentries under its parent
(their grandparent), as creating them under the FIT entry resulted in an
error until FIT was converted into a proper section.
FIT subentries have their offsets relative to the FIT section, and
reading those offsets in the parent section results in wrong data. The
subentries rightfully belong under the FIT entries, so create them
there. Add tests checking that we can extract the correct data for a FIT
entry and its subentries.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Remove '/images/' fragment from FIT subentry paths
Binman FIT entry nodes describe their subentries in an 'images' subnode,
same as how they would be written for the mkimage executable. The entry
type initially manually managed its subentries keyed by their node paths
relative to its base node. It was later converted to a proper section
while still keeping the same keys for subentries.
These subentry keys of sections are used as path fragments, so they must
not contain the path separator character '/'. Otherwise, they won't be
addressable by binman extract/replace commands. Change these keys from
the '/images/foo' forms to the subentry node names. Extend the simple
FIT tests to check for this.
binman: Don't reset offset/size if image doesn't allow repacking
When an image has the 'allow-repack' property, binman includes the
original offset and size properties from the image description in the
fdtmap. These are later used as the packing constraints when replacing
entries in an image, so other unconstrained entries can be freely
positioned.
Replacing an entry in an image without 'allow-repack' (and therefore the
original offsets) follows the same logic and results in entries being
merely concatenated. Instead, skip resetting the calculated offsets and
sizes to the missing originals for these images so that every entry is
constrained to its existing offset/size.
Add tests that replace an entry with smaller or equal-sized data, in an
image that doesn't allow repacking. Attempting to do so with bigger-size
data is already an error that is already being tested.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Collect bintools for images when replacing entries
Binman entries can use other executables to compute their data, usually
in their ObtainContents() methods. Subclasses of Entry_section would use
bintools in their BuildSectionData() method instead, which is called
from several places including their Pack().
These binary tools are resolved correctly while building an image from a
device-tree description so that they can be used from these methods.
However, this is not being done when replacing entries in an image,
which can result in an error as the Pack() methods attempt to use them.
Collect and resolve entries' bintools also when replacing entries to fix
Pack() errors. Add a way to mock bintool usage in the testing entry type
and tests that check bintools are being resolved for such an entry.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Fix unique names having '/.' for images read from files
Binman can embed a copy of the image description into the images it
builds as a fdtmap entry, but it omits the /binman/<image-name> prefix
from the node paths while doing so. When reading an already-built image
file, entries are reconstructed using this fdtmap and their associated
nodes still lack that prefix.
Some entries like fit and vblock create intermediate files whose names
are based on an entry unique name. This name is constructed from their
node's path by concatenating the parents with dots up to the binman
node, e.g. /binman/image/foo/bar becomes 'image.foo.bar'.
However, we don't have this /binman/image prefix when replacing entries
in such an image. The /foo/bar entry we read when doing so erroneously
has the unique name of '/.foo.bar', causing permission errors when the
entry attempts to create files based on that.
Fix the unique-name generation by stopping at the '/' node like how it
stops at the binman node. As the unique names are used as filenames, add
tests that check if they're safe to use as filenames.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 25 Apr 2022 05:31:27 +0000 (23:31 -0600)]
bootstd: Provide a default command
We would like to use bootstd by default when EFI boot manager is not
enabled. But so far bootstd does not support all the of distro-boot
fetures. So for now, add an option to select this.
Simon Glass [Mon, 25 Apr 2022 05:31:25 +0000 (23:31 -0600)]
bootstd: Add setup for the bootflow tests
We need to create a disk image with a partition table and a DOS-format
filesystem containing a few files. Provide a fallback binary for CI since
it does not seem able to detect the loopback partitions.
Add this to a dm_init test so that it happens when needed.
Simon Glass [Mon, 25 Apr 2022 05:31:22 +0000 (23:31 -0600)]
bootstd: Add an implementation of script boot
Add a bootmeth driver which handles distro boot from a disk via a U-Boot
script, so we can boot a bootflow using this commonly used mechanism. This
is required by Armbian, for example.
projects / uboot.git / log