Merge tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, bpf and wireless.
Still no major regressions, the release continues to be calm. An
uptick of fixes this time around due to trivial data race fixes and
patches flowing down from subtrees.
There has been a few driver fixes (particularly a few fixes for false
positives due to f588aa3f3718 which went into -next in May!) that make
me worry the wide testing is not exactly fully through.
So "calm" but not "let's just cut the final ASAP" vibes over here.
Current release - regressions:
- wifi: rtw88: fix write to const table of channel parameters
Current release - new code bugs:
- mac80211: add gfp_t arg to ieeee80211_obss_color_collision_notify
- mlx5:
- TC, allow offload from uplink to other PF's VF
- Lag, decouple FDB selection and shared FDB
- Lag, correct get the port select mode str
- bnxt_en: fix and simplify XDP transmit path
- r8152: fix accessing unset transport header
Previous releases - regressions:
- conntrack: fix crash due to confirmed bit load reordering (after
atomic -> refcount conversion)
- stmmac: dwc-qos: disable split header for Tegra194
Previous releases - always broken:
- mlx5e: ring the TX doorbell on DMA errors
- bpf: make sure mac_header was set before using it
- mac80211: do not wake queues on a vif that is being stopped
- mac80211: fix queue selection for mesh/OCB interfaces
- ip: fix dflt addr selection for connected nexthop
- seg6: fix skb checksums for SRH encapsulation/insertion
- xdp: fix spurious packet loss in generic XDP TX path
- bunch of sysctl data race fixes
- nf_log: incorrect offset to network header
Misc:
- bpf: add flags arg to bpf_dynptr_read and bpf_dynptr_write APIs"
* tag 'net-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
nfp: flower: configure tunnel neighbour on cmsg rx
net/tls: Check for errors in tls_device_init
MAINTAINERS: Add an additional maintainer to the AMD XGBE driver
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
selftests/net: test nexthop without gw
ip: fix dflt addr selection for connected nexthop
net: atlantic: remove aq_nic_deinit() when resume
net: atlantic: remove deep parameter on suspend/resume functions
sfc: fix kernel panic when creating VF
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
sfc: fix use after free when disabling sriov
net: sunhme: output link status with a single print.
r8152: fix accessing unset transport header
net: stmmac: fix leaks in probe
net: ftgmac100: Hold reference returned by of_get_child_by_name()
nexthop: Fix data-races around nexthop_compat_mode.
ipv4: Fix data-races around sysctl_ip_dynaddr.
tcp: Fix a data-race around sysctl_tcp_ecn_fallback.
...
Merge tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three smb3 client fixes:
- two multichannel fixes: fix a potential deadlock freeing a channel,
and fix a race condition on failed creation of a new channel
- mount failure fix: work around a server bug in some common older
Samba servers by avoiding padding at the end of the negotiate
protocol request"
* tag '5.19-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: workaround negprot bug in some Samba servers
cifs: remove unnecessary locking of chan_lock while freeing session
cifs: fix race condition with delayed threads
Merge tag 'nfsd-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable regression fixes:
- Enable SETATTR(time_create) to fix regression with Mac OS clients
- Fix a lockd crasher and broken NLM UNLCK behavior"
* tag 'nfsd-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
lockd: fix nlm_close_files
lockd: set fl_owner when unlocking files
NFSD: Decode NFSv4 birth time attribute
Merge tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity fixes from Mimi Zohar:
"Here are a number of fixes for recently found bugs.
Only 'ima: fix violation measurement list record' was introduced in
the current release. The rest address existing bugs"
* tag 'integrity-v5.19-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: Fix potential memory leak in ima_init_crypto()
ima: force signature verification when CONFIG_KEXEC_SIG is configured
ima: Fix a potential integer overflow in ima_appraise_measurement
ima: fix violation measurement list record
Revert "evm: Fix memleak in init_desc"
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- quieten the spectre-bhb prints
- mark flattened device tree sections as shareable
- remove some obsolete CPU domain code and help text
- fix thumb unaligned access abort emulation
- fix amba_device_add() refcount underflow
- fix literal placement
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
ARM: 9213/1: Print message about disabled Spectre workarounds only once
ARM: 9212/1: domain: Modify Kconfig help text
ARM: 9211/1: domain: drop modify_domain()
ARM: 9210/1: Mark the FDT_FIXED sections as shareable
ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
um: Replace to_phys() and to_virt() with less generic function names
The UML function names to_virt() and to_phys() are exposed by UML
headers, and are very generic and may be defined by drivers. As it
turns out, commit 52dffcc0903f ("pmem: refactor pmem_clear_poison()")
did exactly that.
This results in build errors such as the following when trying to build
um:allmodconfig:
drivers/nvdimm/pmem.c: In function ‘pmem_dax_zero_page_range’:
./arch/um/include/asm/page.h:105:20: error: too few arguments to function ‘to_phys’
105 | #define __pa(virt) to_phys((void *) (unsigned long) (virt))
| ^~~~~~~
Use less generic function names for the um specific to_phys() and
to_virt() functions to fix the problem and to avoid similar problems in
the future.
Fixes: 52dffcc0903f ("pmem: refactor pmem_clear_poison()") Cc: Dan Williams <dan.j.williams@intel.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last one for 5.19. This became bigger than wished, but
all changes are pretty device-specific small fixes, which look less
worrisome.
The majority of changes are about various ASoC fixes, while the usual
HD-audio quirks are included as well"
* tag 'sound-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (28 commits)
ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
ALSA: hda - Add fixup for Dell Latitidue E5430
ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
ALSA: hda/realtek: Fix headset mic for Acer SF313-51
ASoC: Intel: Skylake: Correct the handling of fmt_config flexible array
ASoC: Intel: Skylake: Correct the ssp rate discovery in skl_get_ssp_clks()
ASoC: rt5640: Fix the wrong state of JD1 and JD2
ASoC: Intel: sof_rt5682: fix out-of-bounds array access
ASoC: qdsp6: fix potential memory leak in q6apm_get_audioreach_graph()
ASoC: tas2764: Fix amp gain register offset & default
ASoC: tas2764: Correct playback volume range
ASoC: tas2764: Fix and extend FSYNC polarity handling
ASoC: tas2764: Add post reset delays
ASoC: dt-bindings: Fix description for msm8916
ASoC: doc: Capitalize RESET line name
ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
ASoC: cs47l92: Fix event generation for OUT1 demux
...
nfp: flower: configure tunnel neighbour on cmsg rx
nfp_tun_write_neigh() function will configure a tunnel neighbour when
calling nfp_tun_neigh_event_handler() or nfp_flower_cmsg_process_one_rx()
(with no tunnel neighbour type) from firmware.
When configuring IP on physical port as a tunnel endpoint, no operation
will be performed after receiving the cmsg mentioned above.
Therefore, add a progress to configure tunnel neighbour in this case.
v2: Correct format of fixes tag.
Fixes: 5b89efd39f95 ("nfp: flower: rework tunnel neighbour configuration") Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20220714081915.148378-1-simon.horman@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xen/netback: avoid entering xenvif_rx_next_skb() with an empty rx queue
xenvif_rx_next_skb() is expecting the rx queue not being empty, but
in case the loop in xenvif_rx_action() is doing multiple iterations,
the availability of another skb in the rx queue is not being checked.
amdgpu: disable powerpc support for the newer display engine
The DRM_AMD_DC_DCN display engine support (Raven, Navi, and newer) has
not been building cleanly on powerpc and causes link errors due to
mixing hard- and soft-float object files:
powerpc64-linux-ld: drivers/gpu/drm/amd/amdgpu/../display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o uses soft float
powerpc64-linux-ld: failed to merge target specific data of file drivers/gpu/drm/amd/amdgpu/../display/dc/dcn31/dcn31_resource.o
[..]
and while patches are floating around, it's not exactly obvious what is
going on.
The problem bisects to commit face7150f53c ("powerpc: Book3S 64-bit
outline-only KASAN support") but that is probably more about changing
config variables than the fundamental cause.
Despite the bisection result, a more directly related commit seems to be 478148593acc ("drm/amd/display: move FPU related code from dcn31 to
dml/dcn31 folder"). It's probably a combination of the two.
This has been going on since the merge window, without any final word.
So instead of blindly applying patches that may or may not be the right
thing, let's disable this for now.
As Michael Ellerman says:
"IIUIC this code was never enabled on ppc before, so disabling it seems
like a reasonable fix to get the build clean"
and once we have more actual feedback (and find any potential users) we
can always re-enable it with the patch that fixes the issues and
back-port as necessary.
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:53 +0000 (13:48 +0200)]
selftests/net: test nexthop without gw
This test implement the scenario described in the commit
"ip: fix dflt addr selection for connected nexthop".
The test configures a nexthop object with an output device only (no gateway
address) and a route that uses this nexthop. The goal is to check if the
kernel selects a valid source address.
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:52 +0000 (13:48 +0200)]
ip: fix dflt addr selection for connected nexthop
When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.
When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.
To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.
When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.
Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1
ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0
ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up
ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1
ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument
Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
> cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms
CC: stable@vger.kernel.org Fixes: 0b2837f003c1 ("nexthop: Add support for IPv4 nexthops") Reported-by: Edwin Brossette <edwin.brossette@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ard Biesheuvel [Tue, 31 May 2022 08:49:24 +0000 (09:49 +0100)]
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
LKP reports a build issue on Clang, related to a literal load of
__current issued through the ldr_va macro. This turns out to be due to
the fact that group relocations are disabled when CONFIG_COMPILE_TEST=y,
which means that the ldr_va macro resolves to a pair of LDR
instructions, the first one being a literal load issued too far from its
literal pool.
Due to the introduction of a couple of new uses of this macro in commit 6468297033cf769e ("ARM: 9195/1: entry: avoid explicit literal loads"),
the literal pools end up getting rearranged in a way that causes the
literal for __current to go out of range. Let's fix this up by putting a
.ltorg directive in a suitable place in the code.
Link: https://lore.kernel.org/all/202205290805.1vZLAr36-lkp@intel.com/ Fixes: 6468297033cf769e ("ARM: 9195/1: entry: avoid explicit literal loads") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Wang Kefeng [Tue, 24 May 2022 08:03:46 +0000 (09:03 +0100)]
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
"ARM: 9192/1: amba: fix memory leak in amba_device_try_add()" leads
to a refcount underflow if amba_device_add() fails, which called by
of_amba_device_create(), the of_amba_device_create() already exists
the error handling, so amba_put_device() only need to be added into
amba_deferred_retry().
Fixes: 19051358cbc0 ("ARM: 9192/1: amba: fix memory leak in amba_device_try_add()") Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
aq_nic_deinit() has been called while suspending, so we don't have to call
it again on resume.
Actually, call it again leads to another hang issue when resuming from
S3.
net: atlantic: remove deep parameter on suspend/resume functions
Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit f74dd8aaea2d ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.
When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.
When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
BUG_ON(in_interrupt());
This patch reenables BH to release the buffer.
Log messages when the bug is hit:
kernel BUG at mm/vmalloc.c:2727!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
RIP: 0010:vunmap+0x2e/0x30
...skip...
Call Trace:
__iommu_dma_free+0x96/0x100
efx_nic_free_buffer+0x2b/0x40 [sfc]
efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
efx_ef10_update_stats_vf+0x18/0x40 [sfc]
efx_start_all+0x15e/0x1d0 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xe7/0x1a0
__dev_change_flags+0x1d7/0x240
dev_change_flags+0x21/0x60
...skip...
Fixes: abaa2a47a31d ("sfc: DMA the VF stats only when requested") Reported-by: Ma Yuying <yuma@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
seg6: fix skb checksum for SRH encapsulation/insertion
The Linux kernel supports Segment Routing Header (SRH)
encapsulation/insertion operations by providing the capability to: i)
encapsulate a packet in an outer IPv6 header with a specified SRH; ii)
insert a specified SRH directly after the IPv6 header of the packet.
Note that the insertion operation is also referred to as 'injection'.
The two operations are respectively supported by seg6_do_srh_encap() and
seg6_do_srh_inline(), which operate on the skb associated to the packet as
needed (e.g. adding the necessary headers and initializing them, while
taking care to recalculate the skb checksum).
seg6_do_srh_encap() and seg6_do_srh_inline() do not initialize the payload
length of the IPv6 header, which is carried out by the caller functions.
However, this approach causes the corruption of the skb checksum which
needs to be updated only after initialization of headers is completed
(thanks to Paolo Abeni for detecting this issue).
The patchset fixes the skb checksum corruption by moving the IPv6 header
payload length initialization from the callers of seg6_do_srh_encap() and
seg6_do_srh_inline() directly into these functions.
This patchset is organized as follows:
- patch 1/3, seg6: fix skb checksum evaluation in SRH
encapsulation/insertion;
(* SRH encapsulation/insertion available since v4.10)
- patch 2/3, seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps
behaviors;
(* SRv6 End.B6 and End.B6.Encaps behaviors available since v4.14)
- patch 3/3, seg6: bpf: fix skb checksum in bpf_push_seg6_encap();
(* bpf IPv6 Segment Routing helpers available since v4.18)
Andrea Mayer [Tue, 12 Jul 2022 17:58:37 +0000 (19:58 +0200)]
seg6: bpf: fix skb checksum in bpf_push_seg6_encap()
Both helper functions bpf_lwt_seg6_action() and bpf_lwt_push_encap() use
the bpf_push_seg6_encap() to encapsulate the packet in an IPv6 with Segment
Routing Header (SRH) or insert an SRH between the IPv6 header and the
payload.
To achieve this result, such helper functions rely on bpf_push_seg6_encap()
which, in turn, leverages seg6_do_srh_{encap,inline}() to perform the
required operation (i.e. encap/inline).
This patch removes the initialization of the IPv6 header payload length
from bpf_push_seg6_encap(), as it is now handled properly by
seg6_do_srh_{encap,inline}() to prevent corruption of the skb checksum.
Fixes: 58efdeab0536 ("bpf: Add IPv6 Segment Routing helpers") Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrea Mayer [Tue, 12 Jul 2022 17:58:36 +0000 (19:58 +0200)]
seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps behaviors
The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.
This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.
Fixes: 4afe673f2e87 ("ipv6: sr: implement several seg6local actions") Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrea Mayer [Tue, 12 Jul 2022 17:58:35 +0000 (19:58 +0200)]
seg6: fix skb checksum evaluation in SRH encapsulation/insertion
Support for SRH encapsulation and insertion was introduced with
commit 7ab7a75aa79e ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.
The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.
To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.
Fixes: 7ab7a75aa79e ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels") Reported-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.it Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 14 Jul 2022 03:16:03 +0000 (20:16 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-12
This series contains updates to ice driver only.
Paul fixes detection of E822 devices for firmware update and changes NVM
read for snapshot creation to be done in chunks as some systems cannot
read the entire NVM in the allotted time.
====================
Use after free is detected by kfence when disabling sriov. What was read
after being freed was vf->pci_dev: it was freed from pci_disable_sriov
and later read in efx_ef10_sriov_free_vf_vports, called from
efx_ef10_sriov_free_vf_vswitching.
Set the pointer to NULL at release time to not trying to read it later.
Reproducer and dmesg log (note that kfence doesn't detect it every time):
$ echo 1 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
$ echo 0 > /sys/class/net/enp65s0f0np0/device/sriov_numvfs
BUG: KFENCE: use-after-free read in efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
Use-after-free read at 0x00000000ff3c1ba5 (in kfence-#224):
efx_ef10_sriov_free_vf_vswitching+0x82/0x170 [sfc]
efx_ef10_pci_sriov_disable+0x38/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
allocated by task 6771 on cpu 10 at 3137.860196s:
pci_alloc_dev+0x21/0x60
pci_iov_add_virtfn+0x2a2/0x320
sriov_enable+0x212/0x3e0
efx_ef10_sriov_configure+0x67/0x80 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xba/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
freed by task 6771 on cpu 12 at 3170.991309s:
device_release+0x34/0x90
kobject_cleanup+0x3a/0x130
pci_iov_remove_virtfn+0xd9/0x120
sriov_disable+0x30/0xe0
efx_ef10_pci_sriov_disable+0x57/0x70 [sfc]
efx_pci_sriov_configure+0x24/0x40 [sfc]
sriov_numvfs_store+0xfe/0x140
kernfs_fop_write_iter+0x11c/0x1b0
new_sync_write+0x11f/0x1b0
vfs_write+0x1eb/0x280
ksys_write+0x5f/0xe0
do_syscall_64+0x5c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: f6bd89c2dd99f ("sfc: create vports for VFs and assign random MAC addresses") Reported-by: Yanghang Liu <yanghliu@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220712062642.6915-1-ihuguet@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Steve French [Tue, 12 Jul 2022 05:11:42 +0000 (00:11 -0500)]
smb3: workaround negprot bug in some Samba servers
Mount can now fail to older Samba servers due to a server
bug handling padding at the end of the last negotiate
context (negotiate contexts typically are rounded up to 8
bytes by adding padding if needed). This server bug can
be avoided by switching the order of negotiate contexts,
placing a negotiate context at the end that does not
require padding (prior to the recent netname context fix
this was the case on the client).
Fixes: cc725151f990 ("smb3: fix empty netname context on secondary channels") Reported-by: Julian Sikorski <belegdol@gmail.com> Tested-by: Julian Sikorski <belegdol+github@gmail.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
vf/remap: return the amount of bytes actually deduplicated
When using the FIDEDUPRANGE ioctl, in case of success the requested size
is returned. In some cases this might not be the actual amount of bytes
deduplicated.
This change modifies vfs_dedupe_file_range() to report the actual amount
of bytes deduplicated, instead of the requested amount.
Link: https://lore.kernel.org/linux-fsdevel/5548ef63-62f9-4f46-5793-03165ceccacc@tu-darmstadt.de/ Reported-by: Ansgar Lößer <ansgar.loesser@kom.tu-darmstadt.de> Reported-by: Max Schlecht <max.schlecht@informatik.hu-berlin.de> Reported-by: Björn Scheuermann <scheuermann@kom.tu-darmstadt.de> Cc: Dave Chinner <david@fromorbit.com> Cc: Darrick J Wong <djwong@kernel.org> Signed-off-by: Ansgar Lößer <ansgar.loesser@kom.tu-darmstadt.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'cgroup-for-5.19-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"Fix an old and subtle bug in the migration path.
css_sets are used to track tasks and migrations are tasks moving from
a group of css_sets to another group of css_sets. The migration path
pins all source and destination css_sets in the prep stage.
Unfortunately, it was overloading the same list_head entry to track
sources and destinations, which got confused for migrations which are
partially identity leading to use-after-frees.
Fixed by using dedicated list_heads for tracking sources and
destinations"
* tag 'cgroup-for-5.19-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Use separate src/dst nodes when preloading css_sets for migration
Dave Chinner [Wed, 13 Jul 2022 07:49:15 +0000 (17:49 +1000)]
fs/remap: constrain dedupe of EOF blocks
If dedupe of an EOF block is not constrainted to match against only
other EOF blocks with the same EOF offset into the block, it can
match against any other block that has the same matching initial
bytes in it, even if the bytes beyond EOF in the source file do
not match.
Fix this by constraining the EOF block matching to only match
against other EOF blocks that have identical EOF offsets and data.
This allows "whole file dedupe" to continue to work without allowing
eof blocks to randomly match against partial full blocks with the
same data.
Jianglei Nie [Tue, 12 Jul 2022 01:10:37 +0000 (09:10 +0800)]
ima: Fix potential memory leak in ima_init_crypto()
On failure to allocate the SHA1 tfm, IMA fails to initialize and exits
without freeing the ima_algo_array. Add the missing kfree() for
ima_algo_array to avoid the potential memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com> Fixes: 4ded3392b061 ("ima: Allocate and initialize tfm for each PCR bank") Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
ima: force signature verification when CONFIG_KEXEC_SIG is configured
Currently, an unsigned kernel could be kexec'ed when IMA arch specific
policy is configured unless lockdown is enabled. Enforce kernel
signature verification check in the kexec_file_load syscall when IMA
arch specific policy is configured.
Nick Bowler [Wed, 13 Jul 2022 01:58:35 +0000 (21:58 -0400)]
net: sunhme: output link status with a single print.
This driver currently prints the link status using four separate
printk calls, which these days gets presented to the user as four
distinct messages, not exactly ideal:
[ 32.582778] eth0: Link is up using
[ 32.582828] internal
[ 32.582837] transceiver at
[ 32.582888] 100Mb/s, Full Duplex.
Restructure the display_link_mode function to use a single netdev_info
call to present all this information as a single message, which is much
nicer:
[ 33.640143] hme 0000:00:01.1 eth0: Link is up using internal transceiver at 100Mb/s, Full Duplex.
The display_forced_link_mode function has a similar structure, so adjust
it in a similar fashion.
Signed-off-by: Nick Bowler <nbowler@draconx.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang [Wed, 13 Jul 2022 03:31:11 +0000 (11:31 +0800)]
r8152: fix accessing unset transport header
A warning is triggered by commit f588aa3f3718 ("net: warn if transport
header was not set"). The warning is harmless, because the value from
skb_transport_offset() is only used for skb_is_gso() is true or the
skb->ip_summed is equal to CHECKSUM_PARTIAL.
Fixes: f588aa3f3718 ("net: warn if transport header was not set") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Jul 2022 13:27:38 +0000 (14:27 +0100)]
Merge tag 'wireless-2022-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A small set of fixes for
* queue selection in mesh/ocb
* queue handling on interface stop
* hwsim virtio device vs. some other virtio changes
* dt-bindings email addresses
* color collision memory allocation
* a const variable in rtw88
* shared SKB transmit in the ethernet format path
* P2P client port authorization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 12 Jul 2022 14:42:25 +0000 (17:42 +0300)]
net: stmmac: fix leaks in probe
These two error paths should clean up before returning.
Fixes: 3c7d91cd5f9a ("net: stmmac: Add Ingenic SoCs MAC support.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Liang He [Tue, 12 Jul 2022 06:14:17 +0000 (14:14 +0800)]
net: ftgmac100: Hold reference returned by of_get_child_by_name()
In ftgmac100_probe(), we should hold the refernece returned by
of_get_child_by_name() and use it to call of_node_put() for
reference balance.
Fixes: 11ada22f905c ("net: ftgmac100: Add support for DT phy-handle property") Signed-off-by: Liang He <windhl@126.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nexthop: Fix data-races around nexthop_compat_mode.
While reading nexthop_compat_mode, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: c42c4d1c4809 ("net: ipv4: add sysctl for nexthop api compatibility mode") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
raw: Fix a data-race around sysctl_raw_l3mdev_accept.
While reading sysctl_raw_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: be10a4ae41de ("net: provide a sysctl raw_l3mdev_accept for raw socket lookup with VRFs") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl: Fix data-races in proc_dointvec_ms_jiffies().
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_dointvec_ms_jiffies() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_dointvec_ms_jiffies() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
A sysctl variable is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
This patch changes proc_dou8vec_minmax() to use READ_ONCE() and
WRITE_ONCE() internally to fix data-races on the sysctl side. For now,
proc_dou8vec_minmax() itself is tolerant to a data-race, but we still
need to add annotations on the other subsystem's side.
Fixes: fe2a51c7fe7d ("sysctl: add proc_dou8vec_minmax()") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc221
On a HP 288 Pro G2 MT (X9W02AV), the front mic could not be detected.
In order to get it working, the pin configuration needs to be set
correctly, and the ALC221_FIXUP_HP_288PRO_MIC_NO_PRESENCE fixup needs
to be applied.
Jeremy Szu [Wed, 13 Jul 2022 02:27:04 +0000 (10:27 +0800)]
ALSA: hda/realtek: fix mute/micmute LEDs for HP machines
The HP ProBook 440/450 G9 and EliteBook 640/650 G9 have multiple
motherboard design and they are using different subsystem ID of audio
codec. Add the same quirk for other MBs.
Jakub Kicinski [Wed, 13 Jul 2022 03:36:00 +0000 (20:36 -0700)]
Merge branch 'bnxt_en-5-bug-fixes'
Michael Chan says:
====================
bnxt_en: 5 Bug fixes
This patchset fixes various issues, including SRIOV error unwinding,
one error recovery path, live patch reporting, XDP transmit path,
and PHC clock reading.
====================
The upper 32-bit PHC register is not latched when reading the lower
32-bit PHC register. Current code leaves a small window where we may
not read correct higher order bits if the lower order bits are just about
to wrap around.
This patch fixes this by reading higher order bits twice and makes
sure that final value is correctly paired with its lower 32 bits.
Fixes: bd0bd5797b78 ("bnxt_en: Do not read the PTP PHC during chip reset") Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Tue, 12 Jul 2022 02:26:17 +0000 (22:26 -0400)]
bnxt_en: Fix and simplify XDP transmit path
Fix the missing length hint in the TX BD for the XDP transmit path. The
length hint is required on legacy chips.
Also, simplify the code by eliminating the first_buf local variable.
tx_buf contains the same value. The opaque value only needs to be set
on the first BD. Fix this also for correctness.
Fixes: 4841425dc515 ("bnxt: support transmit and free of aggregation buffers") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan [Tue, 12 Jul 2022 02:26:15 +0000 (22:26 -0400)]
bnxt_en: Fix bnxt_reinit_after_abort() code path
bnxt_reinit_after_abort() is called during ifup when a previous
FW reset sequence has aborted or a previous ifup has failed after
detecting FW reset. In all cases, it is safe to assume that a
previous FW reset has completed and the driver may not have fully
reinitialized.
Prior to this patch, it is assumed that the
FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE flag will always be
set by the firmware in bnxt_hwrm_if_change(). This may not be true if
the driver has already attempted to register with the firmware. The
firmware may not set the RESET_DONE flag again after the driver has
registered, assuming that the driver has seen the flag already.
Fix it to always go through the FW reset initialization path if
the BNXT_STATE_FW_RESET_DET flag is set. This flag is always set
by the driver after successfully going through bnxt_reinit_after_abort().
Fixes: e648c2683d53 ("bnxt_en: attempt to reinitialize after aborted reset") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt_en: reclaim max resources if sriov enable fails
If bnxt_sriov_enable() fails after some resources have been reserved
for the VFs, the current code is not unwinding properly and the
reserved resources become unavailable afterwards. Fix it by
properly unwinding with a call to bnxt_hwrm_func_qcaps() to
reset all maximum resources.
Also, add the missing bnxt_ulp_sriov_cfg() call to let the RDMA
driver know to abort.
Fixes: dfe047769e71 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge tag 'trace-v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Fixes and minor clean ups for tracing:
- Fix memory leak by reverting what was thought to be a double free.
A static tool had gave a false positive that a double free was
possible in the error path, but it was actually a different
location that confused the static analyzer (and those of us that
reviewed it).
- Move use of static buffers by ftrace_dump() to a location that can
be used by kgdb's ftdump(), as it needs it for the same reasons.
- Clarify in the Kconfig description that function tracing has
negligible impact on x86, but may have a bit bigger impact on other
architectures.
- Remove unnecessary extra semicolon in trace event.
- Make a local variable static that is used in the fprobes sample
- Use KSYM_NAME_LEN for length of function in kprobe sample and get
rid of unneeded macro for the same purpose"
* tag 'trace-v5.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
samples: Use KSYM_NAME_LEN for kprobes
fprobe/samples: Make sample_probe static
blk-iocost: tracing: atomic64_read(&ioc->vtime_rate) is assigned an extra semicolon
ftrace: Be more specific about arch impact when function tracer is enabled
tracing: Fix sleeping while atomic in kdb ftdump
tracing/histograms: Fix memory leak problem
sunliming [Mon, 6 Jun 2022 07:56:59 +0000 (15:56 +0800)]
fprobe/samples: Make sample_probe static
This symbol is not used outside of fprobe_example.c, so marks it static.
Fixes the following warning:
sparse warnings: (new ones prefixed by >>)
>> samples/fprobe/fprobe_example.c:23:15: sparse: sparse: symbol 'sample_probe'
was not declared. Should it be static?
Link: https://lkml.kernel.org/r/20220606075659.674556-1-sunliming@kylinos.cn Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: sunliming <sunliming@kylinos.cn> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
ftrace: Be more specific about arch impact when function tracer is enabled
It was brought up that on ARMv7, that because the FUNCTION_TRACER does not
use nops to keep function tracing disabled because of the use of a link
register, it does have some performance impact.
The start of functions when -pg is used to compile the kernel is:
Which just puts the stack back to its normal location. But these two
instructions at the start of every function does incur some overhead.
Be more honest in the Kconfig FUNCTION_TRACER description and specify that
the overhead being in the noise was x86 specific, but other architectures
may vary.
If you drop into kdb and type "ftdump" you'll get a sleeping while
atomic warning from memory allocation in trace_find_next_entry().
This appears to have been caused by commit 7c2a3035d9a2 ("tracing:
Save off entry when peeking at next entry"), which added the
allocation in that path. The problematic commit was already fixed by
commit d2f84cc688f0 ("tracing: Do not allocate buffer in
trace_find_next_entry() in atomic") but that fix missed the kdb case.
The fix here is easy: just move the assignment of the static buffer to
the place where it should have been to begin with:
trace_init_global_iter(). That function is called in two places, once
is right before the assignment of the static buffer added by the
previous fix and once is in kdb.
Note that it appears that there's a second static buffer that we need
to assign that was added in commit ce133cf6c0cd ("tracing: Show real
address for trace event arguments"), so we'll move that too.
As commit 955d06b86ab6 ("tracing: fix double free") said, the
"double free" problem reported by clang static analyzer is:
> In parse_var_defs() if there is a problem allocating
> var_defs.expr, the earlier var_defs.name is freed.
> This free is duplicated by free_var_defs() which frees
> the rest of the list.
However, if there is a problem allocating N-th var_defs.expr:
+ in parse_var_defs(), the freed 'earlier var_defs.name' is
actually the N-th var_defs.name;
+ then in free_var_defs(), the names from 0th to (N-1)-th are freed;
IF ALLOCATING PROBLEM HAPPENED HERE!!! -+
\
|
0th 1th (N-1)-th N-th V
+-------------+-------------+-----+-------------+-----------
var_defs: | name | expr | name | expr | ... | name | expr | name | ///
+-------------+-------------+-----+-------------+-----------
These two frees don't act on same name, so there was no "double free"
problem before. Conversely, after that commit, we get a "memory leak"
problem because the above "N-th var_defs.name" is not freed.
If enable CONFIG_DEBUG_KMEMLEAK and inject a fault at where the N-th
var_defs.expr allocated, then execute on shell like:
$ echo 'hist:key=call_site:val=$v1,$v2:v1=bytes_req,v2=bytes_alloc' > \
/sys/kernel/debug/tracing/events/kmem/kmalloc/trigger
When creating a snapshot of the NVM the driver needs to read the entire
contents from the NVM and store it. The NVM reads are protected by a lock
that is shared between the driver and the firmware.
If the driver takes too long to read the entire NVM (which can happen on
some systems) then the firmware could reclaim the lock and cause subsequent
reads from the driver to fail.
We could fix this by increasing the timeout that we pass to the firmware,
but we could end up in the same situation again if the system is slow.
Instead have the driver break the reading of the NVM into blocks that are
small enough that we have confidence that the read will complete within the
timeout time, but large enough not to cause significant AQ overhead.
Fixes: 5e79cd664497 ("ice: add a devlink region for dumping NVM contents") Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently presumes that the record data in the PLDM header
of the firmware image will match the device ID of the running device.
This is true for E810 devices. It appears that for E822 devices that
this is not guaranteed to be true.
Fix this by adding a check for the generic E822 device.
Fixes: a2e4db181311 ("ice: implement device flash update via devlink") Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Merge tag 'ovl-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fix from Miklos Szeredi:
"Add a temporary fix for posix acls on idmapped mounts introduced in
this cycle. A proper fix will be added in the next cycle"
* tag 'ovl-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: turn off SB_POSIXACL with idmapped layers temporarily
Merge tag 'drm-fixes-2022-07-12' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"I see you picked up one of the fbdev fixes, this is the other stuff
that was queued up last week.
A bit of a scattering of fixes, three for i915, one amdgpu, and a
couple of panfrost, rockchip, panel and bridge ones.
amdgpu:
- Hibernation fix
dma-buf:
- fix use after free of fence
i915:
- Fix a possible refcount leak in DP MST connector (Hangyu)
- Fix on loading guc on ADL-N (Daniele)
- Fix vm use-after-free in vma destruction (Thomas)
* tag 'drm-fixes-2022-07-12' of git://anongit.freedesktop.org/drm/drm:
drm/ssd130x: Fix pre-charge period setting
dma-buf: Fix one use-after-free of fence
drm/i915: Fix vm use-after-free in vma destruction
drm/i915/guc: ADL-N should use the same GuC FW as ADL-S
drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
drm/amdgpu/display: disable prefer_shadow for generic fb helpers
drm/amdgpu: keep fbdev buffers pinned during suspend
drm/panfrost: Fix shrinker list corruption by madvise IOCTL
drm/panfrost: Put mapping instead of shmem obj on panfrost_mmu_map_fault_addr() error
drm/rockchip: Detach from ARM DMA domain in attach_device
drm/bridge: fsl-ldb: Drop DE signal polarity inversion
drm/bridge: fsl-ldb: Enable split mode for LVDS dual link
drm/bridge: fsl-ldb: Fix mode clock rate validation
drm/aperture: Run fbdev removal before internal helpers
drm: panel-orientation-quirks: Add quirk for the Lenovo Yoga Tablet 2 830
cifs: remove unnecessary locking of chan_lock while freeing session
In cifs_put_smb_ses, when we're freeing the last ref count to
the session, we need to free up each channel. At this point,
it is unnecessary to take chan_lock, since we have the last
reference to the ses.
Picking up this lock also introduced a deadlock because it calls
cifs_put_tcp_ses, which locks cifs_tcp_ses_lock.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Acked-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Steve French <stfrench@microsoft.com>
On failure to create a new channel, first cancel the
delayed threads, which could try to search for this
channel, and not find it.
The other option was to put the tcp session for the
channel first, before decrementing chan_count. But
that would leave a reference to the tcp session, when
it has been freed already.
So going with the former option and cancelling the
delayed works first, before rolling back the channel.
Fixes: 31374b92d94a ("cifs: change iface_list from array to sorted linked list") Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Acked-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Steve French <stfrench@microsoft.com>
__static_call_fixup() invokes __static_call_transform() without holding
text_mutex, which causes lockdep to complain in text_poke_bp().
Adding the proper locking cures that, but as this is either used during
early boot or during module finalizing, it's not required to use
text_poke_bp(). Add an argument to __static_call_transform() which tells
it to use text_poke_early() for it.
Fixes: 9bd2b3a6b6f0 ("x86,static_call: Use alternative RET encoding") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de>
ALSA: hda/realtek - Fix headset mic problem for a HP machine with alc671
On a HP 288 Pro G6, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
Merge tag 'x86_bugs_retbleed' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 retbleed fixes from Borislav Petkov:
"Just when you thought that all the speculation bugs were addressed and
solved and the nightmare is complete, here's the next one: speculating
after RET instructions and leaking privileged information using the
now pretty much classical covert channels.
It is called RETBleed and the mitigation effort and controlling
functionality has been modelled similar to what already existing
mitigations provide"
* tag 'x86_bugs_retbleed' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
x86/speculation: Disable RRSBA behavior
x86/kexec: Disable RET on kexec
x86/bugs: Do not enable IBPB-on-entry when IBPB is not supported
x86/entry: Move PUSH_AND_CLEAR_REGS() back into error_entry
x86/bugs: Add Cannon lake to RETBleed affected CPU list
x86/retbleed: Add fine grained Kconfig knobs
x86/cpu/amd: Enumerate BTC_NO
x86/common: Stamp out the stepping madness
KVM: VMX: Prevent RSB underflow before vmenter
x86/speculation: Fill RSB on vmexit for IBRS
KVM: VMX: Fix IBRS handling after vmexit
KVM: VMX: Prevent guest RSB poisoning attacks with eIBRS
KVM: VMX: Convert launched argument to flags
KVM: VMX: Flatten __vmx_vcpu_run()
objtool: Re-add UNWIND_HINT_{SAVE_RESTORE}
x86/speculation: Remove x86_spec_ctrl_mask
x86/speculation: Use cached host SPEC_CTRL value for guest entry/exit
x86/speculation: Fix SPEC_CTRL write on SMT state change
x86/speculation: Fix firmware entry SPEC_CTRL handling
x86/speculation: Fix RSB filling with CONFIG_RETPOLINE=n
...
Dave Airlie [Tue, 12 Jul 2022 00:43:49 +0000 (10:43 +1000)]
Merge tag 'drm-misc-fixes-2022-07-07-1' of ssh://git.freedesktop.org/git/drm/drm-misc into drm-fixes
Three mode setting fixes for fsl-ldb, a fbdev removal use-after-free fix,
a dma-buf fence use-after-free fix, a DMA setup fix for rockchip, an error
path fix and memory corruption fix for panfrost and one more orientation
quirk
Dave Airlie [Tue, 12 Jul 2022 00:40:24 +0000 (10:40 +1000)]
Merge tag 'drm-intel-fixes-2022-07-07' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix a possible refcount leak in DP MST connector (Hangyu)
- Fix on loading guc on ADL-N (Daniele)
- Fix vm use-after-free in vma destruction (Thomas)
Merge tag 'for-5.19-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A more fixes that seem to me to be important enough to get merged
before release:
- in zoned mode, fix leak of a structure when reading zone info, this
happens on normal path so this can be significant
- in zoned mode, revert an optimization added in 5.19-rc1 to finish a
zone when the capacity is full, but this is not reliable in all
cases
- try to avoid short reads for compressed data or inline files when
it's a NOWAIT read, applications should handle that but there are
two, qemu and mariadb, that are affected"
* tag 'for-5.19-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: drop optimization of zone finish
btrfs: zoned: fix a leaked bioc in read_zone_info
btrfs: return -EAGAIN for NOWAIT dio reads/writes on compressed and inline extents
Merge tags 'free-mq_sysctls-for-v5.19' and 'ptrace_unfreeze_fix-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ipc namespace fix from Eric Biederman:
"This fixes a bug with error handling if ipc creation fails that was
reported by syzbot"
For completeness, this also pulls the ptrace_unfreeze_fix tag that
contains the original version of one of the hotfixes that I manually
applied earlier so that it would be fixed in rc6.
* tag 'free-mq_sysctls-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ipc: Free mq_sysctls if ipc namespace creation failed
* tag 'ptrace_unfreeze_fix-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ptrace: fix clearing of JOBCTL_TRACED in ptrace_unfreeze_traced()
Jeff Layton [Mon, 11 Jul 2022 18:30:14 +0000 (14:30 -0400)]
lockd: fix nlm_close_files
This loop condition tries a bit too hard to be clever. Just test for
the two indices we care about explicitly.
Cc: J. Bruce Fields <bfields@fieldses.org> Fixes: 649a9a0eb60a ("Keep read and write fds with each nlm_file") Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Merge tag 'mm-hotfixes-stable-2022-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"Mainly MM fixes. About half for issues which were introduced after
5.18 and the remainder for longer-term issues"
* tag 'mm-hotfixes-stable-2022-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: split huge PUD on wp_huge_pud fallback
nilfs2: fix incorrect masking of permission flags for symlinks
mm/rmap: fix dereferencing invalid subpage pointer in try_to_migrate_one()
riscv/mm: fix build error while PAGE_TABLE_CHECK enabled without MMU
Documentation: highmem: use literal block for code example in highmem.h comment
mm: sparsemem: fix missing higher order allocation splitting
mm/damon: use set_huge_pte_at() to make huge pte old
sh: convert nommu io{re,un}map() to static inline functions
mm: userfaultfd: fix UFFDIO_CONTINUE on fallocated shmem pages
Jeff Layton [Mon, 11 Jul 2022 18:30:13 +0000 (14:30 -0400)]
lockd: set fl_owner when unlocking files
Unlocking a POSIX lock on an inode with vfs_lock_file only works if
the owner matches. Ensure we set it in the request.
Cc: J. Bruce Fields <bfields@fieldses.org> Fixes: 649a9a0eb60a ("Keep read and write fds with each nlm_file") Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Merge tag 'modules-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module fixes from Luis Chamberlain:
"Although most of the move of code in in v5.19-rc1 should have not
introduced a regression patch review on one of the file changes
captured a checkpatch warning which advised to use strscpy() and it
caused a buffer overflow when an incorrect length is passed.
Another change which checkpatch complained about was an odd RCU usage,
but that was properly addressed in a separate patch to the move by
Aaron. That caused a regression with PREEMPT_RT=y due to an unbounded
latency.
This series fixes both and adjusts documentation which we forgot to do
for the move"
* tag 'modules-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module: kallsyms: Ensure preemption in add_kallsyms() with PREEMPT_RT
doc: module: update file references
module: Fix "warning: variable 'exit' set but not used"
module: Fix selfAssignment cppcheck warning
modules: Fix corruption of /proc/kallsyms
Chuck Lever [Sun, 10 Jul 2022 18:46:04 +0000 (14:46 -0400)]
NFSD: Decode NFSv4 birth time attribute
NFSD has advertised support for the NFSv4 time_create attribute
since commit e321c769ecfb ("nfsd: Add support for the birth time
attribute").
Igor Mammedov reports that Mac OS clients attempt to set the NFSv4
birth time attribute via OPEN(CREATE) and SETATTR if the server
indicates that it supports it, but since the above commit was
merged, those attempts now fail.
Table 5 in RFC 8881 lists the time_create attribute as one that can
be both set and retrieved, but the above commit did not add server
support for clients to provide a time_create attribute. IMO that's
a bug in our implementation of the NFSv4 protocol, which this commit
addresses.
Whether NFSD silently ignores the new birth time or actually sets it
is another matter. I haven't found another filesystem service in the
Linux kernel that enables users or clients to modify a file's birth
time attribute.
This commit reflects my (perhaps incorrect) understanding of whether
Linux users can set a file's birth time. NFSD will now recognize a
time_create attribute but it ignores its value. It clears the
time_create bit in the returned attribute bitmask to indicate that
the value was not used.
Reported-by: Igor Mammedov <imammedo@redhat.com> Fixes: e321c769ecfb ("nfsd: Add support for the birth time attribute") Tested-by: Igor Mammedov <imammedo@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
module: kallsyms: Ensure preemption in add_kallsyms() with PREEMPT_RT
The commit 40468939e937 ("module: kallsyms: Fix suspicious rcu usage")
under PREEMPT_RT=y, disabling preemption introduced an unbounded
latency since the loop is not fixed. This change caused a regression
since previously preemption was not disabled and we would dereference
RCU-protected pointers explicitly. That being said, these pointers
cannot change.
Before kallsyms-specific data is prepared/or set-up, we ensure that
the unformed module is known to be unique i.e. does not already exist
(see load_module()). Therefore, we can fix this by using the common and
more appropriate RCU flavour as this section of code can be safely
preempted.
Reported-by: Steven Rostedt <rostedt@goodmis.org> Fixes: 40468939e937 ("module: kallsyms: Fix suspicious rcu usage") Signed-off-by: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
fix race between exit_itimers() and /proc/pid/timers
As Chris explains, the comment above exit_itimers() is not correct,
we can race with proc_timers_seq_ops. Change exit_itimers() to clear
signal->posix_timers with ->siglock held.
ALSA: hda/conexant: Apply quirk for another HP ProDesk 600 G3 model
There is another HP ProDesk 600 G3 model with the PCI SSID 103c:82b4
that requires the quirk HP_MIC_NO_PRESENCE. Add the corresponding
entry to the quirk table.
ALSA: hda/realtek: Fix headset mic for Acer SF313-51
The issue on Acer SWIFT SF313-51 is that headset microphone
doesn't work. The following quirk fixed headset microphone issue.
Note that the fixup of SF314-54/55 (ALC256_FIXUP_ACER_HEADSET_MIC)
was not successful on my SF313-51.
The following patchset contains Netfilter fixes for net:
1) refcount_inc_not_zero() is not semantically equivalent to
atomic_int_not_zero(), from Florian Westphal. My understanding was
that refcount_*() API provides a wrapper to easier debugging of
reference count leaks, however, there are semantic differences
between these two APIs, where refcount_inc_not_zero() needs a barrier.
Reason for this subtle difference to me is unknown.
2) packet logging is not correct for ARP and IP packets, from the
ARP family and netdev/egress respectively. Use skb_network_offset()
to reach the headers accordingly.
3) set element extension length have been growing over time, replace
a BUG_ON by EINVAL which might be triggerable from userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: mptcp: validate userspace PM tests by default
The new script was not listed in the programs to test.
By consequence, some CIs running MPTCP selftests were not validating
these new tests. Note that MPTCP CI was validating it as it executes all
.sh scripts from 'tools/testing/selftests/net/mptcp' directory.
Fixes: 348320406328 ("selftests: mptcp: functional tests for the userspace PM type") Reported-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 8 Jul 2022 23:36:09 +0000 (16:36 -0700)]
mptcp: fix subflow traversal at disconnect time
At disconnect time the MPTCP protocol traverse the subflows
list closing each of them. In some circumstances - MPJ subflow,
passive MPTCP socket, the latter operation can remove the
subflow from the list, invalidating the current iterator.
Address the issue using the safe list traversing helper
variant.
Reported-by: van fantasy <g1042620637@gmail.com> Fixes: 7cc40ad9c3de ("mptcp: full disconnect implementation") Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log