Jose Abreu [Sat, 17 Aug 2019 18:54:43 +0000 (20:54 +0200)]
net: stmmac: Add Split Header support and enable it in XGMAC cores
Add the support for Split Header feature in the RX path and enable it in
XGMAC cores.
This does not impact neither beneficts bandwidth but it does reduces CPU
usage because without the feature all the entire packet is memcpy'ed,
while that with the feature only the header is.
With Split Header disabled 'perf stat -d' gives:
86870.624945 task-clock (msec) # 0.429 CPUs utilized 1073352 context-switches # 0.012 M/sec
1 cpu-migrations # 0.000 K/sec
213 page-faults # 0.002 K/sec 327113872376 cycles # 3.766 GHz (62.53%) 56618161216 instructions # 0.17 insn per cycle (75.06%) 10742205071 branches # 123.658 M/sec (75.36%) 584309242 branch-misses # 5.44% of all branches (75.19%) 17594787965 L1-dcache-loads # 202.540 M/sec (74.88%) 4003773131 L1-dcache-load-misses # 22.76% of all L1-dcache hits (74.89%) 1313301468 LLC-loads # 15.118 M/sec (49.75%) 355906510 LLC-load-misses # 27.10% of all LL-cache hits (49.92%)
With Split Header enabled 'perf stat -d' gives:
49324.456539 task-clock (msec) # 0.245 CPUs utilized 2542387 context-switches # 0.052 M/sec
1 cpu-migrations # 0.000 K/sec
213 page-faults # 0.004 K/sec 177092791469 cycles # 3.590 GHz (62.30%) 68555756017 instructions # 0.39 insn per cycle (75.16%) 12697019382 branches # 257.418 M/sec (74.81%) 442081897 branch-misses # 3.48% of all branches (74.79%) 20337958358 L1-dcache-loads # 412.330 M/sec (75.46%) 3820210140 L1-dcache-load-misses # 18.78% of all L1-dcache hits (75.35%) 1257719198 LLC-loads # 25.499 M/sec (49.73%) 685543923 LLC-load-misses # 54.51% of all LL-cache hits (49.86%)
Changes from v2:
- Reword commit message (Jakub)
Changes from v1:
- Add performance info (David)
- Add misssing dma_sync_single_for_device()
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Aug 2019 19:40:09 +0000 (12:40 -0700)]
Merge branch 'drop_monitor-for-offloaded-paths'
Ido Schimmel says:
====================
Add drop monitor for offloaded data paths
Users have several ways to debug the kernel and understand why a packet
was dropped. For example, using drop monitor and perf. Both utilities
trace kfree_skb(), which is the function called when a packet is freed
as part of a failure. The information provided by these tools is
invaluable when trying to understand the cause of a packet loss.
In recent years, large portions of the kernel data path were offloaded
to capable devices. Today, it is possible to perform L2 and L3
forwarding in hardware, as well as tunneling (IP-in-IP and VXLAN).
Different TC classifiers and actions are also offloaded to capable
devices, at both ingress and egress.
However, when the data path is offloaded it is not possible to achieve
the same level of introspection since packets are dropped by the
underlying device and never reach the kernel.
This patchset aims to solve this by allowing users to monitor packets
that the underlying device decided to drop along with relevant metadata
such as the drop reason and ingress port.
The above is achieved by exposing a fundamental capability of devices
capable of data path offloading - packet trapping. In much the same way
as drop monitor registers its probe function with the kfree_skb()
tracepoint, the device is instructed to pass to the CPU (trap) packets
that it decided to drop in various places in the pipeline.
The configuration of the device to pass such packets to the CPU is
performed using devlink, as it is not specific to a port, but rather to
a device. In the future, we plan to control the policing of such packets
using devlink, in order not to overwhelm the CPU.
While devlink is used as the control path, the dropped packets are
passed along with metadata to drop monitor, which reports them to
userspace as netlink events. This allows users to use the same interface
for the monitoring of both software and hardware drops.
In order to reduce the patch count, this patchset only includes
integration with netdevsim. A follow-up patchset will add devlink-trap
support in mlxsw.
Patches #1-#7 extend drop monitor to also monitor hardware originated
drops.
Patches #8-#10 add the devlink-trap infrastructure.
Patches #11-#12 add devlink-trap support in netdevsim.
Patches #13-#16 add tests for the generic infrastructure over netdevsim.
Example
=======
Instantiate netdevsim
---------------------
List supported traps
--------------------
netdevsim/netdevsim10:
name source_mac_is_multicast type drop generic true action drop group l2_drops
name vlan_tag_mismatch type drop generic true action drop group l2_drops
name ingress_vlan_filter type drop generic true action drop group l2_drops
name ingress_spanning_tree_filter type drop generic true action drop group l2_drops
name port_list_is_empty type drop generic true action drop group l2_drops
name port_loopback_filter type drop generic true action drop group l2_drops
name fid_miss type exception generic false action trap group l2_drops
name blackhole_route type drop generic true action drop group l3_drops
name ttl_value_is_too_small type exception generic true action trap group l3_drops
name tail_drop type drop generic true action drop group buffer_drops
Enable a trap
-------------
Query statistics
----------------
netdevsim/netdevsim10:
name blackhole_route type drop generic true action trap group l3_drops
stats:
rx:
bytes 7384 packets 52
Monitor dropped packets
-----------------------
dropwatch> set alertmode packet
Setting alert mode
Alert mode successfully set
dropwatch> set sw true
setting software drops monitoring to 1
dropwatch> set hw true
setting hardware drops monitoring to 1
dropwatch> start
Enabling monitoring...
Kernel monitoring activated.
Issue Ctrl-C to stop monitoring
drop at: ttl_value_is_too_small (l3_drops)
origin: hardware
input port ifindex: 55
input port name: eth0
timestamp: Mon Aug 12 10:52:20 2019 445911505 nsec
protocol: 0x800
length: 142
original length: 142
drop at: ip6_mc_input+0x8b8/0xef8 (0xffffffff9e2bb0e8)
origin: software
input port ifindex: 4
timestamp: Mon Aug 12 10:53:37 2019 024444587 nsec
protocol: 0x86dd
length: 110
original length: 110
Future plans
============
* Provide more drop reasons as well as more metadata
* Add dropmon support to libpcap, so that tcpdump/tshark could
specifically listen on dropmon traffic, instead of capturing all
netlink packets via nlmon interface
Changes in v3:
* Place test with the rest of the netdevsim tests
* Fix test to load netdevsim module
* Move devlink helpers from the test to devlink_lib.sh. Will be used
by mlxsw tests
* Re-order netdevsim includes in alphabetical order
* Fix reverse xmas tree in netdevsim
* Remove double include in netdevsim
Changes in v2:
* Use drop monitor to report dropped packets instead of devlink
* Add drop monitor patches
* Add test cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:24 +0000 (16:28 +0300)]
selftests: devlink_trap: Add test cases for devlink-trap
Add test cases for devlink-trap on top of the netdevsim implementation.
The tests focus on the devlink-trap core infrastructure and user space
API. They test both good and bad flows and also dismantle of the netdev
and devlink device used to report trapped packets.
This allows device drivers to focus their tests on device-specific
functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:22 +0000 (16:28 +0300)]
selftests: forwarding: devlink_lib: Allow tests to define devlink device
For tests that create their network interfaces dynamically or do not use
interfaces at all (as with netdevsim) it is useful to define their own
devlink device instead of deriving it from the first network interface.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:20 +0000 (16:28 +0300)]
netdevsim: Add devlink-trap support
Have netdevsim register its trap groups and traps with devlink during
initialization and periodically report trapped packets to devlink core.
Since netdevsim is not a real device, the trapped packets are emulated
using a workqueue that periodically reports a UDP packet with a random
5-tuple from each active packet trap and from each running netdev.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:17 +0000 (16:28 +0300)]
devlink: Add packet trap infrastructure
Add the basic packet trap infrastructure that allows device drivers to
register their supported packet traps and trap groups with devlink.
Each driver is expected to provide basic information about each
supported trap, such as name and ID, but also the supported metadata
types that will accompany each packet trapped via the trap. The
currently supported metadata type is just the input port, but more will
be added in the future. For example, output port and traffic class.
Trap groups allow users to set the action of all member traps. In
addition, users can retrieve per-group statistics in case per-trap
statistics are too narrow. In the future, the trap group object can be
extended with more attributes, such as policer settings which will limit
the amount of traffic generated by member traps towards the CPU.
Beside registering their packet traps with devlink, drivers are also
expected to report trapped packets to devlink along with relevant
metadata. devlink will maintain packets and bytes statistics for each
packet trap and will potentially report the trapped packet with its
metadata to user space via drop monitor netlink channel.
The interface towards the drivers is simple and allows devlink to set
the action of the trap. Currently, only two actions are supported:
'trap' and 'drop'. When set to 'trap', the device is expected to provide
the sole copy of the packet to the driver which will pass it to devlink.
When set to 'drop', the device is expected to drop the packet and not
send a copy to the driver. In the future, more actions can be added,
such as 'mirror'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:16 +0000 (16:28 +0300)]
drop_monitor: Allow user to start monitoring hardware drops
Drop monitor has start and stop commands, but so far these were only
used to start and stop monitoring of software drops.
Now that drop monitor can also monitor hardware drops, we should allow
the user to control these as well.
Do that by adding SW and HW flags to these commands. If no flag is
specified, then only start / stop monitoring software drops. This is
done in order to maintain backward-compatibility with existing user
space applications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:15 +0000 (16:28 +0300)]
drop_monitor: Add support for summary alert mode for hardware drops
In summary alert mode a notification is sent with a list of recent drop
reasons and a count of how many packets were dropped due to this reason.
To avoid expensive operations in the context in which packets are
dropped, each CPU holds an array whose number of entries is the maximum
number of drop reasons that can be encoded in the netlink notification.
Each entry stores the drop reason and a count. When a packet is dropped
the array is traversed and a new entry is created or the count of an
existing entry is incremented.
Later, in process context, the array is replaced with a newly allocated
copy and the old array is encoded in a netlink notification. To avoid
breaking user space, the notification includes the ancillary header,
which is 'struct net_dm_alert_msg' with number of entries set to '0'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:14 +0000 (16:28 +0300)]
drop_monitor: Add support for packet alert mode for hardware drops
In a similar fashion to software drops, extend drop monitor to send
netlink events when packets are dropped by the underlying hardware.
The main difference is that instead of encoding the program counter (PC)
from which kfree_skb() was called in the netlink message, we encode the
hardware trap name. The two are mostly equivalent since they should both
help the user understand why the packet was dropped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:11 +0000 (16:28 +0300)]
drop_monitor: Initialize hardware per-CPU data
Like software drops, hardware drops also need the same type of per-CPU
data. Therefore, initialize it during module initialization and
de-initialize it during module exit.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sat, 17 Aug 2019 13:28:10 +0000 (16:28 +0300)]
drop_monitor: Move per-CPU data init/fini to separate functions
Currently drop monitor only reports software drops to user space, but
subsequent patches are going to add support for hardware drops.
Like software drops, the per-CPU data of hardware drops needs to be
initialized and de-initialized upon module initialization and exit. To
avoid code duplication, break this code into separate functions, so that
these could be re-used for hardware drops.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 17 Aug 2019 19:36:57 +0000 (12:36 -0700)]
Merge branch 'bridge-mdb'
Nikolay Aleksandrov says:
====================
net: bridge: mdb: allow dump/add/del of host-joined entries
This set makes the bridge dump host-joined mdb entries, they should be
treated as normal entries since they take a slot and are aging out.
We already have notifications for them but we couldn't dump them until
now so they remained hidden. We dump them similar to how they're
notified, in order to keep user-space compatibility with the dumped
objects (e.g. iproute2 dumps mdbs in a format which can be fed into
add/del commands) we allow host-joined groups also to be added/deleted via
mdb commands. That can later be used for L2 mcast MAC manipulation as
was recently discussed. Note that iproute2 changes are not necessary,
this set will work with the current user-space mdb code.
Patch 01 - a trivial comment move
Patch 02 - factors out the mdb filling code so it can be
re-used for the host-joined entries
Patch 03 - dumps host-joined entries
Patch 04 - allows manipulation of host-joined entries via standard mdb
calls
v3: fix compiler warning in patch 04 (DaveM)
v2: change patch 04 to avoid double notification and improve host group
manual removal if no ports are present in the group
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mdb: allow add/delete for host-joined groups
Currently this is needed only for user-space compatibility, so similar
object adds/deletes as the dumped ones would succeed. Later it can be
used for L2 mcast MAC add/delete.
v3: fix compiler warning (DaveM)
v2: don't send a notification when used from user-space, arm the group
timer if no ports are left after host entry del
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: mdb: dump host-joined entries as well
Currently we dump only the port mdb entries but we can have host-joined
entries on the bridge itself and they should be treated as normal temp
mdbs, they're already notified:
$ bridge monitor all
[MDB]dev br0 port br0 grp ff02::8 temp
The group will not be shown in the bridge mdb output, but it takes 1 slot
and it's timing out. If it's only host-joined then the mdb show output
can even be empty.
After this patch we show the host-joined groups:
$ bridge mdb show
dev br0 port br0 grp ff02::8 temp
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove genphy_config_init.
v2:
- remove call also from new adin driver
v3:
- pass NULL as config_init function pointer for dp83848
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 17 Aug 2019 10:29:25 +0000 (12:29 +0200)]
net: phy: remove calls to genphy_config_init
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.
v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bill Sommerfeld [Thu, 15 Aug 2019 00:10:43 +0000 (17:10 -0700)]
ipvlan: set hw_enc_features like macvlan
Allow encapsulated packets sent to tunnels layered over ipvlan to use
offloads rather than forcing SW fallbacks.
Since commit 9ac9361d2fa7c59478b8 ("macvlan: add offload features for
encapsulation"), macvlan has set dev->hw_enc_features to include
everything in dev->features; do likewise in ipvlan.
Signed-off-by: Bill Sommerfeld <wsommerfeld@google.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 14 Aug 2019 17:11:51 +0000 (10:11 -0700)]
selftests: Fix get_ifidx and callers in nettest.c
Dan reported:
The patch ec491d6e4b01: "selftests: Add nettest" from Aug 1, 2019,
leads to the following static checker warning:
./tools/testing/selftests/net/nettest.c:1690 main()
warn: unsigned 'tmp' is never less than zero.
./tools/testing/selftests/net/nettest.c
1680 case '1':
1681 args.has_expected_raddr = 1;
1682 if (convert_addr(&args, optarg,
1683 ADDR_TYPE_EXPECTED_REMOTE))
1684 return 1;
1685
1686 break;
1687 case '2':
1688 if (str_to_uint(optarg, 0, 0x7ffffff, &tmp) != 0) {
1689 tmp = get_ifidx(optarg);
1690 if (tmp < 0) {
"tmp" is unsigned so it can't be negative. Also all the callers assume
that get_ifidx() returns negatives on error but it looks like it really
returns zero on error so it's a bit unclear to me.
Update get_ifidx to return -1 on errors and cleanup callers of it.
Fixes: ec491d6e4b01 ("selftests: Add nettest") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Wed, 14 Aug 2019 14:40:24 +0000 (16:40 +0200)]
net: dsa: mv88e6xxx: check for mode change in port_setup_mac
The mv88e6xxx_port_setup_mac checks if the requested MAC settings are
different from the current ones, and if not, does nothing (since chaning
them requires putting the link down).
In this check it only looks if the triplet [link, speed, duplex] is
being changed.
This patch adds support to also check if the mode parameter (of type
phy_interface_t) is requested to be changed. The current mode is
computed by the ->port_link_state() method, and if it is different from
PHY_INTERFACE_MODE_NA, we check for equality with the requested mode.
In the implementations of the mv88e6250_port_link_state() method we set
the current mode to PHY_INTERFACE_MODE_NA - so the code does not check
for mode change on 6250.
In the mv88e6352_port_link_state() method, we use the cached cmode of
the port to determine the mode as phy_interface_t (and if it is not
enough, eg. for RGMII, we also look at the port control register for
RX/TX timings).
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: phy: adin: add support for Analog Devices PHYs
This changeset adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main
difference being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec, i.e. no extra SW configuration
required.
This changeset also implements the ability to configure the chips via SW
registers.
dt-bindings: net: add bindings for ADIN PHY driver
This change adds bindings for the Analog Devices ADIN PHY driver, detailing
all the properties implemented by the driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change implements retrieving all the error counters from the PHY.
The counters require that the RxErrCnt register (0x0014) be read first,
after which copies of the counters are latched into the registers. This
ensures that all registers read after RxErrCnt are synchronized at the
moment that they are read.
The counter values need to be accumulated by the driver, as each time that
RxErrCnt is read, the values that are latched are the ones that have
incremented from the last read.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: implement downshift configuration via phy-tunable
Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs
Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.
This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).
Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.
In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: add EEE translation layer from Clause 45 to Clause 22
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.
The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.
For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: add support MDI/MDIX/Auto-MDI selection
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: make RGMII internal delays configurable
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: configure RGMII/RMII/MII modes on config
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This change hooks link-status-change interrupts to phylib.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: hook genphy_{suspend, resume} into the driver
The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: adin: add support for Analog Devices PHYs
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Aug 2019 23:31:12 +0000 (16:31 -0700)]
Merge branch 'mscc-PTP-support'
Antoine Tenart says:
====================
net: mscc: PTP Hardware Clock (PHC) support
This series introduces the PTP Hardware Clock (PHC) support to the Mscc
Ocelot switch driver. In order to make use of this, a new register bank
is added and described in the device tree, as well as a new interrupt.
The use this bank and interrupt was made optional in the driver for dt
compatibility reasons.
Thanks!
Antoine
Since v5:
- Made sure both the PTP interrupt and register bank were available to
enable supporting h/w timestamping.
- Added a check after a kzalloc.
- Add Reviewed-by tags from Andrew.
Since v4:
- Added SKBTX_IN_PROGRESS.
- Fixed two xmas trees.
- Rework the loop condition in ocelot_ptp_rdy_irq_handler.
Since v3:
- Fixed a spin_unlock_irqrestore issue.
Since v2:
- Prevented from a possible infinite loop when reading the h/w
timestamps.
- s/GFP_KERNEL/GFP_ATOMIC/ in the Tx path.
- Set rx_filter to HWTSTAMP_FILTER_PTP_V2_EVENT at probe.
- Fixed s/w timestamping dependencies.
- Added Paul Burton's Acked-by on patches 2 and 4.
Since v1:
- Used list_for_each_safe() in ocelot_deinit().
- Fixed a memory leak in ocelot_deinit() by calling
dev_kfree_skb_any().
- Fixed a locking issue in get_hwtimestamp().
- Handled the NULL case of ptp_clock_register().
- Added comments on optional dt properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 12 Aug 2019 14:45:37 +0000 (16:45 +0200)]
net: mscc: PTP Hardware Clock (PHC) support
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 12 Aug 2019 14:45:36 +0000 (16:45 +0200)]
net: mscc: remove the frame_info cpuq member
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 12 Aug 2019 14:45:34 +0000 (16:45 +0200)]
net: mscc: describe the PTP register range
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 12 Aug 2019 14:45:33 +0000 (16:45 +0200)]
Documentation/bindings: net: ocelot: document the PTP ready IRQ
One additional interrupt needs to be described within the Ocelot device
tree node: the PTP ready one. This patch documents the binding needed to
do so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Mon, 12 Aug 2019 14:45:32 +0000 (16:45 +0200)]
Documentation/bindings: net: ocelot: document the PTP bank
One additional register range needs to be described within the Ocelot
device tree node: the PTP. This patch documents the binding needed to do
so.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Aug 2019 19:54:45 +0000 (12:54 -0700)]
Merge branch 'qed-NVM'
Sudarsana Reddy Kalluru says:
====================
qed*: Support for NVM config attributes.
The patch series adds support for managing the NVM config attributes.
Patch (1) adds functionality to update config attributes via MFW.
Patch (2) adds driver interface for updating the config attributes.
Changes from previous versions:
-------------------------------
v4: Added more details on the functionality and its usage.
v3: Removed unused variable.
v2: Removed unused API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add driver API for flashing the config attributes.
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds API for configuring the NVM config attributes using
Management FW (MFW) interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request for net-next/master consisting of 41 patches.
The first two patches are for the kvaser_pciefd driver: Christer Beskow
removes unnecessary code in the kvaser_pciefd_pwm_stop() function,
YueHaibing removes the unused including of <linux/version.h>.
In the next patch YueHaibing also removes the unused including of
<linux/version.h> in the f81601 driver.
In the ti_hecc driver the next 6 patches are by me and fix checkpatch
warnings. YueHaibing's patch removes an unused variable in the
ti_hecc_mailbox_read() function.
The next 6 patches all target the xilinx_can driver. Anssi Hannula's
patch fixes a chip start failure with an invalid bus. The patch by
Venkatesh Yadav Abbarapu skips an error message in case of a deferred
probe. The 3 patches by Appana Durga Kedareswara rao fix the RX and TX
path for CAN-FD frames. Srinivas Neeli's patch fixes the bit timing
calculations for CAN-FD.
The next 12 patches are by me and several checkpatch warnings in the
af_can, raw and bcm components.
Thomas Gleixner provides a patch for the bcm, which switches the timer
to HRTIMER_MODE_SOFT and removes the hrtimer_tasklet.
Then 6 more patches by me for the gw component, which fix checkpatch
warnings, followed by 2 patches by Oliver Hartkopp to add CAN-FD
support.
The vcan driver gets 3 patches by me, fixing checkpatch warnings.
And finally a patch by Andre Hartmann to fix typos in CAN's netlink
header.
====================
Jonathan Lemon [Tue, 13 Aug 2019 17:45:09 +0000 (10:45 -0700)]
page_pool: fix logic in __page_pool_get_cached
__page_pool_get_cached() will return NULL when the ring is
empty, even if there are pages present in the lookaside cache.
It is also possible to refill the cache, and then return a
NULL page.
Restructure the logic so eliminate both cases.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Aug 2019 19:04:24 +0000 (12:04 -0700)]
Merge branch 'rds-next'
Gerd Rausch says:
====================
net/rds: Fixes from internal Oracle repo
This is the first set of (mostly old) patches from our internal repository
in an effort to synchronize what Oracle had been using internally
with what is shipped with the Linux kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 13 Jan 2011 19:40:31 +0000 (11:40 -0800)]
rds: check for excessive looping in rds_send_xmit
Original commit from 2011 updated to include a change by
Yuval Shaia <yuval.shaia@oracle.com>
that adds a new statistic counter "send_stuck_rm"
to capture the messages looping exessively
in the send path.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 8fbe2d4485b7 ("RDS: add stat for socket recv memory usage") Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Mason [Fri, 3 Feb 2012 16:08:51 +0000 (11:08 -0500)]
RDS: don't use GFP_ATOMIC for sk_alloc in rds_create
Signed-off-by: Chris Mason <chris.mason@oracle.com> Signed-off-by: Bang Nguyen <bang.nguyen@oracle.com> Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com> Signed-off-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Mason [Fri, 3 Feb 2012 16:07:54 +0000 (11:07 -0500)]
RDS: limit the number of times we loop in rds_send_xmit
This will kick the RDS worker thread if we have been looping
too long.
Original commit from 2012 updated to include a change by
Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
that triggers "must_wake" if "rds_ib_recv_refill_one" fails.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Aug 2019 13:46:34 +0000 (15:46 +0200)]
selftests: netdevsim: add devlink regions tests
Test netdevsim devlink region implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Aug 2019 13:46:33 +0000 (15:46 +0200)]
netdevsim: implement support for devlink region and snapshots
Implement dummy region of size 32K and allow user to create snapshots
or random data using debugfs file trigger.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 15 Aug 2019 13:42:29 +0000 (15:42 +0200)]
selftests: netdevsim: add devlink params tests
Test recently added netdevsim devlink param implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 15 Aug 2019 12:41:00 +0000 (20:41 +0800)]
page_pool: remove unnecessary variable init
Remove variable initializations in functions that
are followed by assignments before use
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Aug 2019 18:48:30 +0000 (11:48 -0700)]
Merge branch 'realtek-EEE'
Heiner Kallweit says:
====================
net: phy: realtek: map vendor-specific EEE registers to standard MMD registers
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control and to significantly simplify
the r8169 driver.
v2:
- rebase patch 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 15 Aug 2019 12:14:18 +0000 (14:14 +0200)]
r8169: use the generic EEE management functions
Now that the Realtek PHY driver maps the vendor-specific EEE registers
to the standard MMD registers, we can remove all special handling and
use the generic functions phy_ethtool_get/set_eee.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 15 Aug 2019 12:12:55 +0000 (14:12 +0200)]
net: phy: realtek: add support for EEE registers on integrated PHY's
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 15 Aug 2019 11:19:22 +0000 (13:19 +0200)]
net: phy: swphy: emulate register MII_ESTATUS
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 15 Aug 2019 11:15:19 +0000 (13:15 +0200)]
net: phy: read MII_CTRL1000 in genphy_read_status only if needed
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ka-Cheong Poon [Thu, 15 Aug 2019 09:36:43 +0000 (02:36 -0700)]
net/rds: Add RDS6_INFO_SOCKETS and RDS6_INFO_RECV_MESSAGES options
Add support of the socket options RDS6_INFO_SOCKETS and
RDS6_INFO_RECV_MESSAGES which update the RDS_INFO_SOCKETS and
RDS_INFO_RECV_MESSAGES options respectively. The old options work
for IPv4 sockets only.
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Tue, 13 Aug 2019 08:00:25 +0000 (10:00 +0200)]
net/mvpp2: Replace tasklet with softirq hrtimer
The tx_done_tasklet tasklet is used in invoke the hrtimer
(mvpp2_hr_timer_cb) in softirq context. This can be also achieved without
the tasklet but with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nft_bitwise: Adjust parentheses to fix memcmp size argument
clang warns:
net/netfilter/nft_bitwise.c:138:50: error: size argument in 'memcmp'
call is a comparison [-Werror,-Wmemsize-comparison]
if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
~~~~~~~~~~~~~~~~~~^~
net/netfilter/nft_bitwise.c:138:6: note: did you mean to compare the
result of 'memcmp' instead?
if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
^
)
net/netfilter/nft_bitwise.c:138:32: note: explicitly cast the argument
to size_t to silence this warning
if (memcmp(&priv->xor, &zero, sizeof(priv->xor) ||
^
(size_t)(
1 error generated.
Adjust the parentheses so that the result of the sizeof is used for the
size argument in memcmp, rather than the result of the comparison (which
would always be true because sizeof is a non-zero number).
Fixes: f0475442fa5f ("netfilter: nft_bitwise: add offload support") Link: https://github.com/ClangBuiltLinux/linux/issues/638 Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jeremy Sowden [Wed, 14 Aug 2019 08:01:28 +0000 (09:01 +0100)]
netfilter: remove deprecation warnings from uapi headers.
There are two netfilter userspace headers which contain deprecation
warnings. While these headers are not used within the kernel, they are
compiled stand-alone for header-testing.
Pablo informs me that userspace iptables still refer to these headers,
and the intention was to use xt_LOG.h instead and remove these, but
userspace was never updated.
Remove the warnings.
Fixes: ab99177269bf ("kbuild: remove all netfilter headers from header-test blacklist.") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Heiner Kallweit [Tue, 13 Aug 2019 06:09:32 +0000 (08:09 +0200)]
net: phy: realtek: add NBase-T PHY auto-detection
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 12 Aug 2019 18:47:40 +0000 (20:47 +0200)]
r8169: fix sporadic transmit timeout issue
Holger reported sporadic transmit timeouts and it turned out that one
path misses ringing the doorbell. Fix was suggested by Eric.
Fixes: 8f1e9cfbbd4a ("r8169: make use of xmit_more") Suggested-by: Eric Dumazet <edumazet@google.com> Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Rename mss field to mss_option field in synproxy, from Fernando Mancera.
2) Use SYSCTL_{ZERO,ONE} definitions in conntrack, from Matteo Croce.
3) More strict validation of IPVS sysctl values, from Junwei Hu.
4) Remove unnecessary spaces after on the right hand side of assignments,
from yangxingwu.
5) Add offload support for bitwise operation.
6) Extend the nft_offload_reg structure to store immediate date.
7) Collapse several ip_set header files into ip_set.h, from
Jeremy Sowden.
8) Make netfilter headers compile with CONFIG_KERNEL_HEADER_TEST=y,
from Jeremy Sowden.
9) Fix several sparse warnings due to missing prototypes, from
Valdis Kletnieks.
10) Use static lock initialiser to ensure connlabel spinlock is
initialized on boot time to fix sched/act_ct.c, patch
from Florian Westphal.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Hayes Wang [Tue, 13 Aug 2019 03:42:06 +0000 (11:42 +0800)]
r8152: replace array with linking list for rx information
The original method uses an array to store the rx information. The
new one uses a list to link each rx structure. Then, it is possible
to increase/decrease the number of rx structure dynamically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Heiner Kallweit [Mon, 12 Aug 2019 21:52:19 +0000 (23:52 +0200)]
net: phy: let phy_speed_down/up support speeds >1Gbps
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Heiner Kallweit [Mon, 12 Aug 2019 21:51:27 +0000 (23:51 +0200)]
net: phy: add phy_speed_down_core and phy_resolve_min_speed
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Vlad Buslov [Mon, 12 Aug 2019 17:02:02 +0000 (20:02 +0300)]
net: devlink: remove redundant rtnl lock assert
It is enough for caller of devlink_compat_switch_id_get() to hold the net
device to guarantee that devlink port is not destroyed concurrently. Remove
rtnl lock assertion and modify comment to warn user that they must hold
either rtnl lock or reference to net device. This is necessary to
accommodate future implementation of rtnl-unlocked TC offloads driver
callbacks.
====================
The following pull-request contains BPF updates for your *net-next* tree.
There is a small merge conflict in libbpf (Cc Andrii so he's in the loop
as well):
for (i = 1; i <= btf__get_nr_types(btf); i++) {
t = (struct btf_type *)btf__type_by_id(btf, i);
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
<<<<<<< HEAD
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t+1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && kind == BTF_KIND_DATASEC) {
=======
t->size = sizeof(int);
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 32);
} else if (!has_datasec && btf_is_datasec(t)) {
>>>>>>> 73d55cf00658e20c495f10b6c0c365f844219c5a
/* replace DATASEC with STRUCT */
Conflict is between the two commits d1241e51cb34 ("libbpf: sanitize VAR to
conservative 1-byte INT") and b604d87c05ba ("libbpf: convert libbpf code to
use new btf helpers"), so we need to pick the sanitation fixup as well as
use the new btf_is_datasec() helper and the whitespace cleanup. Looks like
the following:
[...]
if (!has_datasec && btf_is_var(t)) {
/* replace VAR with INT */
t->info = BTF_INFO_ENC(BTF_KIND_INT, 0, 0);
/*
* using size = 1 is the safest choice, 4 will be too
* big and cause kernel BTF validation failure if
* original variable took less than 4 bytes
*/
t->size = 1;
*(int *)(t + 1) = BTF_INT_ENC(0, 0, 8);
} else if (!has_datasec && btf_is_datasec(t)) {
/* replace DATASEC with STRUCT */
[...]
The main changes are:
1) Addition of core parts of compile once - run everywhere (co-re) effort,
that is, relocation of fields offsets in libbpf as well as exposure of
kernel's own BTF via sysfs and loading through libbpf, from Andrii.
More info on co-re: http://vger.kernel.org/bpfconf2019.html#session-2
and http://vger.kernel.org/lpc-bpf2018.html#session-2
2) Enable passing input flags to the BPF flow dissector to customize parsing
and allowing it to stop early similar to the C based one, from Stanislav.
3) Add a BPF helper function that allows generating SYN cookies from XDP and
tc BPF, from Petar.
4) Add devmap hash-based map type for more flexibility in device lookup for
redirects, from Toke.
5) Improvements to XDP forwarding sample code now utilizing recently enabled
devmap lookups, from Jesper.
6) Add support for reporting the effective cgroup progs in bpftool, from Jakub
and Takshak.
7) Fix reading kernel config from bpftool via /proc/config.gz, from Peter.
8) Fix AF_XDP umem pages mapping for 32 bit architectures, from Ivan.
9) Follow-up to add two more BPF loop tests for the selftest suite, from Alexei.
10) Add perf event output helper also for other skb-based program types, from Allan.
11) Fix a co-re related compilation error in selftests, from Yonghong.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
projects / kernel.git / log