Like Xu [Sat, 9 Apr 2022 01:52:26 +0000 (09:52 +0800)]
KVM: x86/pmu: Update AMD PMC sample period to fix guest NMI-watchdog
NMI-watchdog is one of the favorite features of kernel developers,
but it does not work in AMD guest even with vPMU enabled and worse,
the system misrepresents this capability via /proc.
This is a PMC emulation error. KVM does not pass the latest valid
value to perf_event in time when guest NMI-watchdog is running, thus
the perf_event corresponding to the watchdog counter will enter the
old state at some point after the first guest NMI injection, forcing
the hardware register PMC0 to be constantly written to 0x800000000001.
Meanwhile, the running counter should accurately reflect its new value
based on the latest coordinated pmc->counter (from vPMC's point of view)
rather than the value written directly by the guest.
Fixes: 44ab0217af7f ("KVM: x86: Adjust counter sample period after a wrmsr") Reported-by: Dongli Cao <caodongli@kingsoft.com> Signed-off-by: Like Xu <likexu@tencent.com> Reviewed-by: Yanan Wang <wangyanan55@huawei.com> Tested-by: Yanan Wang <wangyanan55@huawei.com> Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220409015226.38619-1-likexu@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Wanpeng Li [Mon, 18 Apr 2022 07:42:32 +0000 (00:42 -0700)]
x86/kvm: Preserve BSP MSR_KVM_POLL_CONTROL across suspend/resume
MSR_KVM_POLL_CONTROL is cleared on reset, thus reverting guests to
host-side polling after suspend/resume. Non-bootstrap CPUs are
restored correctly by the haltpoll driver because they are hot-unplugged
during suspend and hot-plugged during resume; however, the BSP
is not hotpluggable and remains in host-sde polling mode after
the guest resume. The makes the guest pay for the cost of vmexits
every time the guest enters idle.
Fix it by recording BSP's haltpoll state and resuming it during guest
resume.
Cc: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1650267752-46796-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: Skip KVM_GUESTDBG_BLOCKIRQ APICv update if APICv is disabled
Skip the APICv inhibit update for KVM_GUESTDBG_BLOCKIRQ if APICv is
disabled at the module level to avoid having to acquire the mutex and
potentially process all vCPUs. The DISABLE inhibit will (barring bugs)
never be lifted, so piling on more inhibits is unnecessary.
Fixes: 4fe180dc1b9a ("KVM: x86: inhibit APICv when KVM_GUESTDBG_BLOCKIRQ active") Cc: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220420013732.3308816-5-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: Pend KVM_REQ_APICV_UPDATE during vCPU creation to fix a race
Make a KVM_REQ_APICV_UPDATE request when creating a vCPU with an
in-kernel local APIC and APICv enabled at the module level. Consuming
kvm_apicv_activated() and stuffing vcpu->arch.apicv_active directly can
race with __kvm_set_or_clear_apicv_inhibit(), as vCPU creation happens
before the vCPU is fully onlined, i.e. it won't get the request made to
"all" vCPUs. If APICv is globally inhibited between setting apicv_active
and onlining the vCPU, the vCPU will end up running with APICv enabled
and trigger KVM's sanity check.
Mark APICv as active during vCPU creation if APICv is enabled at the
module level, both to be optimistic about it's final state, e.g. to avoid
additional VMWRITEs on VMX, and because there are likely bugs lurking
since KVM checks apicv_active in multiple vCPU creation paths. While
keeping the current behavior of consuming kvm_apicv_activated() is
arguably safer from a regression perspective, force apicv_active so that
vCPU creation runs with deterministic state and so that if there are bugs,
they are found sooner than later, i.e. not when some crazy race condition
is hit.
KVM: nVMX: Defer APICv updates while L2 is active until L1 is active
Defer APICv updates that occur while L2 is active until nested VM-Exit,
i.e. until L1 regains control. vmx_refresh_apicv_exec_ctrl() assumes L1
is active and (a) stomps all over vmcs02 and (b) neglects to ever updated
vmcs01. E.g. if vmcs12 doesn't enable the TPR shadow for L2 (and thus no
APICv controls), L1 performs nested VM-Enter APICv inhibited, and APICv
becomes unhibited while L2 is active, KVM will set various APICv controls
in vmcs02 and trigger a failed VM-Entry. The kicker is that, unless
running with nested_early_check=1, KVM blames L1 and chaos ensues.
In all cases, ignoring vmcs02 and always deferring the inhibition change
to vmcs01 is correct (or at least acceptable). The ABSENT and DISABLE
inhibitions cannot truly change while L2 is active (see below).
IRQ_BLOCKING can change, but it is firmly a best effort debug feature.
Furthermore, only L2's APIC is accelerated/virtualized to the full extent
possible, e.g. even if L1 passes through its APIC to L2, normal MMIO/MSR
interception will apply to the virtual APIC managed by KVM.
The exception is the SELF_IPI register when x2APIC is enabled, but that's
an acceptable hole.
Lastly, Hyper-V's Auto EOI can technically be toggled if L1 exposes the
MSRs to L2, but for that to work in any sane capacity, L1 would need to
pass through IRQs to L2 as well, and IRQs must be intercepted to enable
virtual interrupt delivery. I.e. exposing Auto EOI to L2 and enabling
VID for L2 are, for all intents and purposes, mutually exclusive.
Lack of dynamic toggling is also why this scenario is all but impossible
to encounter in KVM's current form. But a future patch will pend an
APICv update request _during_ vCPU creation to plug a race where a vCPU
that's being created doesn't get included in the "all vCPUs request"
because it's not yet visible to other vCPUs. If userspaces restores L2
after VM creation (hello, KVM selftests), the first KVM_RUN will occur
while L2 is active and thus service the APICv update request made during
VM creation.
Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220420013732.3308816-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: Tag APICv DISABLE inhibit, not ABSENT, if APICv is disabled
Set the DISABLE inhibit, not the ABSENT inhibit, if APICv is disabled via
module param. A recent refactoring to add a wrapper for setting/clearing
inhibits unintentionally changed the flag, probably due to a copy+paste
goof.
Fixes: bc691fca4628 ("KVM: x86: Trace all APICv inhibit changes and capture overall status") Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220420013732.3308816-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: Initialize debugfs_dentry when a VM is created to avoid NULL deref
Initialize debugfs_entry to its semi-magical -ENOENT value when the VM
is created. KVM's teardown when VM creation fails is kludgy and calls
kvm_uevent_notify_change() and kvm_destroy_vm_debugfs() even if KVM never
attempted kvm_create_vm_debugfs(). Because debugfs_entry is zero
initialized, the IS_ERR() checks pass and KVM derefs a NULL pointer.
Fixes: c3d82a65b83c ("KVM: Don't create VM debugfs files outside of the VM directory") Cc: stable@vger.kernel.org Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oupton@google.com> Reported-by: syzbot+df6fbbd2ee39f21289ef@syzkaller.appspotmail.com Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Oliver Upton <oupton@google.com>
Message-Id: <20220415004622.2207751-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: Add helpers to wrap vcpu->srcu_idx and yell if it's abused
Add wrappers to acquire/release KVM's SRCU lock when stashing the index
in vcpu->src_idx, along with rudimentary detection of illegal usage,
e.g. re-acquiring SRCU and thus overwriting vcpu->src_idx. Because the
SRCU index is (currently) either 0 or 1, illegal nesting bugs can go
unnoticed for quite some time and only cause problems when the nested
lock happens to get a different index.
Wrap the WARNs in PROVE_RCU=y, and make them ONCE, otherwise KVM will
likely yell so loudly that it will bring the kernel to its knees.
Signed-off-by: Sean Christopherson <seanjc@google.com> Tested-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20220415004343.2203171-4-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: RISC-V: Use kvm_vcpu.srcu_idx, drop RISC-V's unnecessary copy
Use the generic kvm_vcpu's srcu_idx instead of using an indentical field
in RISC-V's version of kvm_vcpu_arch. Generic KVM very intentionally
does not touch vcpu->srcu_idx, i.e. there's zero chance of running afoul
of common code.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220415004343.2203171-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86: Don't re-acquire SRCU lock in complete_emulated_io()
Don't re-acquire SRCU in complete_emulated_io() now that KVM acquires the
lock in kvm_arch_vcpu_ioctl_run(). More importantly, don't overwrite
vcpu->srcu_idx. If the index acquired by complete_emulated_io() differs
from the one acquired by kvm_arch_vcpu_ioctl_run(), KVM will effectively
leak a lock and hang if/when synchronize_srcu() is invoked for the
relevant grace period.
Fixes: a7b7f3d93b37 ("KVM: x86: pull kvm->srcu read-side to kvm_arch_vcpu_ioctl_run") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220415004343.2203171-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
RISC-V: KVM: Restrict the extensions that can be disabled
Currently, the config isa register allows us to disable all allowed
single letter ISA extensions. It shouldn't be the case as vmm shouldn't
be able to disable base extensions (imac).
These extensions should always be enabled as long as they are enabled
in the host ISA.
RISC-V: KVM: Remove 's' & 'u' as valid ISA extension
There are no ISA extension defined as 's' & 'u' in RISC-V specifications.
The misa register defines 's' & 'u' bit as Supervisor/User privilege mode
enabled. But it should not appear in the ISA extension in the device tree.
Remove those from the allowed ISA extension for kvm.
Merge tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixlet from Juergen Gross:
"A single cleanup patch for the Xen balloon driver"
* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: don't use PV mode extra memory for zone device allocations
Merge tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Two x86 fixes related to TSX:
- Use either MSR_TSX_FORCE_ABORT or MSR_IA32_TSX_CTRL to disable TSX
to cover all CPUs which allow to disable it.
- Disable TSX development mode at boot so that a microcode update
which provides TSX development mode does not suddenly make the
system vulnerable to TSX Asynchronous Abort"
* tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsx: Disable TSX development mode at boot
x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits
Merge tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for the timers core:
- Fix the warning condition in __run_timers() which does not take
into account that a CPU base (especially the deferrable base) never
has a timer armed on it and therefore the next_expiry value can
become stale.
- Replace a WARN_ON() in the NOHZ code with a WARN_ON_ONCE() to
prevent endless spam in dmesg.
- Remove the double star from a comment which is not meant to be in
kernel-doc format"
* tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/sched: Fix non-kernel-doc comment
tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
timers: Fix warning condition in __run_timers()
Merge tag 'smp-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP fixes from Thomas Gleixner:
"Two fixes for the SMP core:
- Make the warning condition in flush_smp_call_function_queue()
correct, which checked a just emptied list head for being empty
instead of validating that there was no pending entry on the
offlined CPU at all.
- The @cpu member of struct cpuhp_cpu_state is initialized when the
CPU hotplug thread for the upcoming CPU is created. That's too late
because the creation of the thread can fail and then the following
rollback operates on CPU0. Get rid of the CPU member and hand the
CPU number to the involved functions directly"
* tag 'smp-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
smp: Fix offline cpu check in flush_smp_call_function_queue()
Merge tag 'irq-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for the interrupt affinity spreading logic to take into
account that there can be an imbalance between present and possible
CPUs, which causes already assigned bits to be overwritten"
* tag 'irq-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Consider that CPUs on nodes can be unbalanced
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Regular set of fixes for drivers and the dev-interface"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: Fix undefined behavior due to shift overflowing the constant
i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
i2c: dev: check return value when calling dev_set_name()
i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
i2c: pasemi: Wait for write xfers to finish
Merge tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A single fix for gpio-sim and two patches for GPIO ACPI pulled from
Andy:
- fix the set/get_multiple() callbacks in gpio-sim
- use correct format characters in gpiolib-acpi
- use an unsigned type for pins in gpiolib-acpi"
* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sim: fix setting and getting multiple lines
gpiolib: acpi: Convert type for pin to be unsigned
gpiolib: acpi: use correct format characters
Merge tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Per your suggestion, random reads now won't fail if there's a page
fault after some non-zero amount of data has been read, which makes
the behavior consistent with all other reads in the kernel.
- Rather than an inconsistent mix of random_get_entropy() returning an
unsigned long or a cycles_t, now it just returns an unsigned long.
- A memcpy() was replaced with an memmove(), because the addresses are
sometimes overlapping. In practice the destination is always before
the source, so not really an issue, but better to be correct than
not.
* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: use memmove instead of memcpy for remaining 32 bytes
random: make random_get_entropy() return an unsigned long
random: allow partial reads if later user copies fail
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"13 fixes, all in drivers.
The most extensive changes are in the iscsi series (affecting drivers
qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
simple revert and then minor updates to pm80xx"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
scsi: qedi: Fix failed disconnect handling
scsi: iscsi: Fix NOP handling during conn recovery
scsi: iscsi: Merge suspend fields
scsi: iscsi: Fix unbound endpoint error handling
scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
scsi: iscsi: Fix endpoint reuse regression
scsi: iscsi: Release endpoint ID when its freed
scsi: iscsi: Fix offload conn cleanup when iscsid restarts
scsi: iscsi: Move iscsi_ep_disconnect()
scsi: pm80xx: Enable upper inbound, outbound queues
scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
Revert "scsi: scsi_debug: Address races following module load"
random: use memmove instead of memcpy for remaining 32 bytes
In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Subsystems affected by this patch series: MAINTAINERS, binfmt, and
mm (tmpfs, secretmem, kasan, kfence, pagealloc, zram, compaction,
hugetlb, vmalloc, and kmemleak)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore
revert "fs/binfmt_elf: use PT_LOAD p_align values for static PIE"
revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"
hugetlb: do not demote poisoned hugetlb pages
mm: compaction: fix compiler warning when CONFIG_COMPACTION=n
mm: fix unexpected zeroed page mapping with zram swap
mm, page_alloc: fix build_zonerefs_node()
mm, kfence: support kmem_dump_obj() for KFENCE objects
kasan: fix hw tags enablement when KUNIT tests are disabled
irq_work: use kasan_record_aux_stack_noalloc() record callstack
mm/secretmem: fix panic when growing a memfd_secret
tmpfs: fix regressions from wider use of ZERO_PAGE
MAINTAINERS: Broadcom internal lists aren't maintainers
Merge tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix memory corruption in DM integrity target when tag_size is less
than digest size.
- Fix DM multipath's historical-service-time path selector to not use
sched_clock() and ktime_get_ns(); only use ktime_get_ns().
- Fix dm_io->orig_bio NULL pointer dereference in dm_zone_map_bio() due
to 5.18 changes that overlooked DM zone's use of ->orig_bio
- Fix for regression that broke the use of dm_accept_partial_bio() for
"abnormal" IO (e.g. WRITE ZEROES) that does not need duplicate bios
- Fix DM's issuing of empty flush bio so that it's size is 0.
* tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix bio length of empty flush
dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
dm zone: fix NULL pointer dereference in dm_zone_map_bio
dm mpath: only use ktime_get_ns() in historical selector
dm integrity: fix memory corruption when tag_size is less than digest size
Patrick Wang [Fri, 15 Apr 2022 02:14:04 +0000 (19:14 -0700)]
mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
The kmemleak_*_phys() apis do not check the address for lowmem's min
boundary, while the caller may pass an address below lowmem, which will
trigger an oops:
The callers may not quite know the actual address they pass(e.g. from
devicetree). So the kmemleak_*_phys() apis should guarantee the address
they finally use is in lowmem range, so check the address for lowmem's
min boundary.
Link: https://lkml.kernel.org/r/20220413122925.33856-1-patrick.wang.shcn@gmail.com Signed-off-by: Patrick Wang <patrick.wang.shcn@gmail.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore
Commit 4ff07ace5097 ("mm, x86: Saving vmcore with non-lazy freeing of
vmas") introduced set_iounmap_nonlazy(), which sets vmap_lazy_nr to
lazy_max_pages() + 1, ensuring that any future vunmaps() immediately
purge the vmap areas instead of doing it lazily.
Commit 9771b8084548 ("mm/vmalloc: Move draining areas out of caller
context") moved the purging from the vunmap() caller to a worker thread.
Unfortunately, set_iounmap_nonlazy() can cause the worker thread to spin
(possibly forever). For example, consider the following scenario:
1. Thread reads from /proc/vmcore. This eventually calls
__copy_oldmem_page() -> set_iounmap_nonlazy(), which sets
vmap_lazy_nr to lazy_max_pages() + 1.
2. Then it calls free_vmap_area_noflush() (via iounmap()), which adds 2
pages (one page plus the guard page) to the purge list and
vmap_lazy_nr. vmap_lazy_nr is now lazy_max_pages() + 3, so the
drain_vmap_work is scheduled.
3. Thread returns from the kernel and is scheduled out.
4. Worker thread is scheduled in and calls drain_vmap_area_work(). It
frees the 2 pages on the purge list. vmap_lazy_nr is now
lazy_max_pages() + 1.
5. This is still over the threshold, so it tries to purge areas again,
but doesn't find anything.
6. Repeat 5.
If the system is running with only one CPU (which is typicial for kdump)
and preemption is disabled, then this will never make forward progress:
there aren't any more pages to purge, so it hangs. If there is more
than one CPU or preemption is enabled, then the worker thread will spin
forever in the background. (Note that if there were already pages to be
purged at the time that set_iounmap_nonlazy() was called, this bug is
avoided.)
This can be reproduced with anything that reads from /proc/vmcore
multiple times. E.g., vmcore-dmesg /proc/vmcore.
It turns out that improvements to vmap() over the years have obsoleted
the need for this "optimization". I benchmarked `dd if=/proc/vmcore
of=/dev/null` with 4k and 1M read sizes on a system with a 32GB vmcore.
The test was run on 5.17, 5.18-rc1 with a fix that avoided the hang, and
5.18-rc1 with set_iounmap_nonlazy() removed entirely:
Andrew Morton [Fri, 15 Apr 2022 02:13:55 +0000 (19:13 -0700)]
revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"
Commit 56af6cb2b2c083 ("fs/binfmt_elf: fix PT_LOAD p_align values for
loaders") was an attempt to fix regressions due to 0303e713e7a4f1
("fs/binfmt_elf: use PT_LOAD p_align values for static PIE").
Mike Kravetz [Fri, 15 Apr 2022 02:13:52 +0000 (19:13 -0700)]
hugetlb: do not demote poisoned hugetlb pages
It is possible for poisoned hugetlb pages to reside on the free lists.
The huge page allocation routines which dequeue entries from the free
lists make a point of avoiding poisoned pages. There is no such check
and avoidance in the demote code path.
If a hugetlb page on the is on a free list, poison will only be set in
the head page rather then the page with the actual error. If such a
page is demoted, then the poison flag may follow the wrong page. A page
without error could have poison set, and a page with poison could not
have the flag set.
Check for poison before attempting to demote a hugetlb page. Also,
return -EBUSY to the caller if only poisoned pages are on the free list.
mm: compaction: fix compiler warning when CONFIG_COMPACTION=n
The below warning is reported when CONFIG_COMPACTION=n:
mm/compaction.c:56:27: warning: 'HPAGE_FRAG_CHECK_INTERVAL_MSEC' defined but not used [-Wunused-const-variable=]
56 | static const unsigned int HPAGE_FRAG_CHECK_INTERVAL_MSEC = 500;
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by moving 'HPAGE_FRAG_CHECK_INTERVAL_MSEC' under
CONFIG_COMPACTION defconfig.
Also since this is just a 'static const int' type, use #define for it.
Link: https://lkml.kernel.org/r/1647608518-20924-1-git-send-email-quic_charante@quicinc.com Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com> Reported-by: kernel test robot <lkp@intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Nitin Gupta <nigupta@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minchan Kim [Fri, 15 Apr 2022 02:13:46 +0000 (19:13 -0700)]
mm: fix unexpected zeroed page mapping with zram swap
Two processes under CLONE_VM cloning, user process can be corrupted by
seeing zeroed page unexpectedly.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage valid data
swap_slot_free_notify
delete zram entry
swap_readpage zeroed(invalid) data
pte_lock
map the *zero data* to userspace
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return and next refault will
read zeroed data
The swap_slot_free_notify is bogus for CLONE_VM case since it doesn't
increase the refcount of swap slot at copy_mm so it couldn't catch up
whether it's safe or not to discard data from backing device. In the
case, only the lock it could rely on to synchronize swap slot freeing is
page table lock. Thus, this patch gets rid of the swap_slot_free_notify
function. With this patch, CPU A will see correct data.
CPU A CPU B
do_swap_page do_swap_page
SWP_SYNCHRONOUS_IO path SWP_SYNCHRONOUS_IO path
swap_readpage original data
pte_lock
map the original data
swap_free
swap_range_free
bd_disk->fops->swap_slot_free_notify
swap_readpage read zeroed data
pte_unlock
pte_lock
if (!pte_same)
goto out_nomap;
pte_unlock
return
on next refault will see mapped data by CPU B
The concern of the patch would increase memory consumption since it
could keep wasted memory with compressed form in zram as well as
uncompressed form in address space. However, most of cases of zram uses
no readahead and do_swap_page is followed by swap_free so it will free
the compressed form from in zram quickly.
Link: https://lkml.kernel.org/r/YjTVVxIAsnKAXjTd@google.com Fixes: 86551ac92432 ("mm, swap: skip swapcache for swapin of synchronous device") Reported-by: Ivan Babrou <ivan@cloudflare.com> Tested-by: Ivan Babrou <ivan@cloudflare.com> Signed-off-by: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 7f7a1f9d2a83 ("mm, vmscan: only allocate and reclaim from
zones with pages managed by the buddy allocator") only zones with free
memory are included in a built zonelist. This is problematic when e.g.
all memory of a zone has been ballooned out when zonelists are being
rebuilt.
The decision whether to rebuild the zonelists when onlining new memory
is done based on populated_zone() returning 0 for the zone the memory
will be added to. The new zone is added to the zonelists only, if it
has free memory pages (managed_zone() returns a non-zero value) after
the memory has been onlined. This implies, that onlining memory will
always free the added pages to the allocator immediately, but this is
not true in all cases: when e.g. running as a Xen guest the onlined new
memory will be added only to the ballooned memory list, it will be freed
only when the guest is being ballooned up afterwards.
Another problem with using managed_zone() for the decision whether a
zone is being added to the zonelists is, that a zone with all memory
used will in fact be removed from all zonelists in case the zonelists
happen to be rebuilt.
Use populated_zone() when building a zonelist as it has been done before
that commit.
There was a report that QubesOS (based on Xen) is hitting this problem.
Xen has switched to use the zone device functionality in kernel 5.9 and
QubesOS wants to use memory hotplugging for guests in order to be able
to start a guest with minimal memory and expand it as needed. This was
the report leading to the patch.
Link: https://lkml.kernel.org/r/20220407120637.9035-1-jgross@suse.com Fixes: 7f7a1f9d2a83 ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator") Signed-off-by: Juergen Gross <jgross@suse.com> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Wei Yang <richard.weiyang@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marco Elver [Fri, 15 Apr 2022 02:13:40 +0000 (19:13 -0700)]
mm, kfence: support kmem_dump_obj() for KFENCE objects
Calling kmem_obj_info() via kmem_dump_obj() on KFENCE objects has been
producing garbage data due to the object not actually being maintained
by SLAB or SLUB.
Fix this by implementing __kfence_obj_info() that copies relevant
information to struct kmem_obj_info when the object was allocated by
KFENCE; this is called by a common kmem_obj_info(), which also calls the
slab/slub/slob specific variant now called __kmem_obj_info().
For completeness, kmem_dump_obj() now displays if the object was
allocated by KFENCE.
Link: https://lore.kernel.org/all/20220323090520.GG16885@xsang-OptiPlex-9020/ Link: https://lkml.kernel.org/r/20220406131558.3558585-1-elver@google.com Fixes: 592e91c79f9e ("mm, kfence: insert KFENCE hooks for SLUB") Fixes: 97b051559488 ("mm, kfence: insert KFENCE hooks for SLAB") Signed-off-by: Marco Elver <elver@google.com> Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com> Reported-by: kernel test robot <oliver.sang@intel.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> [slab] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kasan: fix hw tags enablement when KUNIT tests are disabled
Kasan enables hw tags via kasan_enable_tagging() which based on the mode
passed via kernel command line selects the correct hw backend.
kasan_enable_tagging() is meant to be invoked indirectly via the cpu
features framework of the architectures that support these backends.
Currently the invocation of this function is guarded by
CONFIG_KASAN_KUNIT_TEST which allows the enablement of the correct backend
only when KUNIT tests are enabled in the kernel.
This inconsistency was introduced in commit:
305bbe44d9bb ("kasan: test: support async (again) and asymm modes for HW_TAGS")
... and prevents to enable MTE on arm64 when KUNIT tests for kasan hw_tags are
disabled.
Fix the issue making sure that the CONFIG_KASAN_KUNIT_TEST guard does not
prevent the correct invocation of kasan_enable_tagging().
Link: https://lkml.kernel.org/r/20220408124323.10028-1-vincenzo.frascino@arm.com Fixes: 305bbe44d9bb ("kasan: test: support async (again) and asymm modes for HW_TAGS") Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
irq_work: use kasan_record_aux_stack_noalloc() record callstack
On PREEMPT_RT kernel and KASAN is enabled. the kasan_record_aux_stack()
may call alloc_pages(), and the rt-spinlock will be acquired, if currently
in atomic context, will trigger warning:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 239, name: bootlogd
Preemption disabled at:
[<ffffffffbab1a531>] rt_mutex_slowunlock+0xa1/0x4e0
CPU: 3 PID: 239 Comm: bootlogd Tainted: G W 5.17.1-rt17-yocto-preempt-rt+ #105
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
Call Trace:
__might_resched.cold+0x13b/0x173
rt_spin_lock+0x5b/0xf0
get_page_from_freelist+0x20c/0x1610
__alloc_pages+0x25e/0x5e0
__stack_depot_save+0x3c0/0x4a0
kasan_save_stack+0x3a/0x50
__kasan_record_aux_stack+0xb6/0xc0
kasan_record_aux_stack+0xe/0x10
irq_work_queue_on+0x6a/0x1c0
pull_rt_task+0x631/0x6b0
do_balance_callbacks+0x56/0x80
__balance_callbacks+0x63/0x90
rt_mutex_setprio+0x349/0x880
rt_mutex_slowunlock+0x22a/0x4e0
rt_spin_unlock+0x49/0x80
uart_write+0x186/0x2b0
do_output_char+0x2e9/0x3a0
n_tty_write+0x306/0x800
file_tty_write.isra.0+0x2af/0x450
tty_write+0x22/0x30
new_sync_write+0x27c/0x3a0
vfs_write+0x3f7/0x5d0
ksys_write+0xd9/0x180
__x64_sys_write+0x43/0x50
do_syscall_64+0x44/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fix it by using kasan_record_aux_stack_noalloc() to avoid the call to
alloc_pages().
The basic reason for this is, when we grow with ftruncate, we call down
into simple_setattr, and then truncate_inode_pages_range, and eventually
we try to zero part of the memory. The normal truncation code does this
via the direct map (i.e., it calls page_address() and hands that to
memset()).
For memfd_secret though, we specifically don't map our pages via the
direct map (i.e. we call set_direct_map_invalid_noflush() on every
fault). So the address returned by page_address() isn't useful, and
when we try to memset() with it we panic.
This patch avoids the panic by implementing a custom setattr for
memfd_secret, which detects resizes specifically (setting the size for
the first time works just fine, since there are no existing pages to try
to zero), and rejects them with EINVAL.
One could argue growing should be supported, but I think that will
require a significantly more lengthy change. So, I propose a minimal
fix for the benefit of stable kernels, and then perhaps to extend
memfd_secret to support growing in a separate patch.
tmpfs: fix regressions from wider use of ZERO_PAGE
Chuck Lever reported fsx-based xfstests generic 075 091 112 127 failing
when 5.18-rc1 NFS server exports tmpfs: bisected to recent tmpfs change.
Whilst nfsd_splice_action() does contain some questionable handling of
repeated pages, and Chuck was able to work around there, history from
Mark Hemment makes clear that there might be similar dangers elsewhere:
it was not a good idea for me to pass ZERO_PAGE down to unknown actors.
Revert shmem_file_read_iter() to using ZERO_PAGE for holes only when
iter_is_iovec(); in other cases, use the more natural iov_iter_zero()
instead of copy_page_to_iter().
We would use iov_iter_zero() throughout, but the x86 clear_user() is not
nearly so well optimized as copy to user (dd of 1T sparse tmpfs file
takes 57 seconds rather than 44 seconds).
And now pagecache_init() does not need to SetPageUptodate(ZERO_PAGE(0)):
which had caused boot failure on arm noMMU STM32F7 and STM32H7 boards
Link: https://lkml.kernel.org/r/9a978571-8648-e830-5735-1f4748ce2e30@google.com Fixes: 16ab34ae02c1 ("tmpfs: do not allocate pages on read") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-by: Patrice CHOTARD <patrice.chotard@foss.st.com> Reported-by: Chuck Lever III <chuck.lever@oracle.com> Tested-by: Chuck Lever III <chuck.lever@oracle.com> Cc: Mark Hemment <markhemm@googlemail.com> Cc: Patrice CHOTARD <patrice.chotard@foss.st.com> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Lukas Czerner <lczerner@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: "Darrick J. Wong" <djwong@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2c: ismt: Fix undefined behavior due to shift overflowing the constant
Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Andy Shevchenko [Mon, 11 Apr 2022 18:07:51 +0000 (21:07 +0300)]
i2c: dev: check return value when calling dev_set_name()
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 716178cba346 ("i2c: dev: Fix the race between the release of i2c_dev and cdev") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Marek Vasut [Fri, 8 Apr 2022 17:15:24 +0000 (19:15 +0200)]
i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
Martin Povišer [Tue, 29 Mar 2022 18:38:17 +0000 (20:38 +0200)]
i2c: pasemi: Wait for write xfers to finish
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: a04f225eb00d ("i2c: PA Semi SMBus driver") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Reviewed-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Wolfram Sang <wsa@kernel.org>
The commit 4b8796317ce3 ("dm: use bio_clone_fast in alloc_io/alloc_tio")
removed bio_clone_fast() call from alloc_tio() when ci->io->tio is
available. In this case, ci->bio is not copied to ci->io->tio.clone.
This is fine since init_clone_info() sets same values to ci->bio and
ci->io->tio.clone.
However, when incoming bios have REQ_PREFLUSH flag, __send_empty_flush()
prepares a zero length bio on stack and set it to ci->bio. At this time,
ci->io->tio.clone still keeps non-zero length. When alloc_tio() chooses
this ci->io->tio.clone as the bio to map, it is passed to targets as
non-empty flush bio. It causes bio length check failure in dm-zoned and
unexpected operation such as dm_accept_partial_bio() call.
To avoid the non-empty flush bio, set zero length to ci->io->tio.clone
in __send_empty_flush().
Fixes: 4b8796317ce3 ("dm: use bio_clone_fast in alloc_io/alloc_tio") Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Merge tag 'block-5.18-2022-04-15' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Moving of lower_48_bits() to the block layer and a fix for the
unaligned_be48 added with that originally (Alexander, Keith)
- Fix a bad WARN_ON() for trim size checking (Ming)
- A polled IO timeout fix for null_blk (Ming)
- Silence IO error printing for dead disks (Christoph)
- Compat mode range fix (Khazhismel)
- NVMe pull request via Christoph:
- Tone down the error logging added this merge window a bit
(Chaitanya Kulkarni)
- Quirk devices with non-unique unique identifiers (Christoph)
* tag 'block-5.18-2022-04-15' of git://git.kernel.dk/linux-block:
block: don't print I/O error warning for dead disks
block/compat_ioctl: fix range check in BLKGETSIZE
nvme-pci: disable namespace identifiers for Qemu controllers
nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
nvme: add a quirk to disable namespace identifiers
nvme: don't print verbose errors for internal passthrough requests
block: null_blk: end timed out poll request
block: fix offset/size check in bio_trim()
asm-generic: fix __get_unaligned_be48() on 32 bit platforms
block: move lower_48_bits() to block
Merge tag 'io_uring-5.18-2022-04-14' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Ensure we check and -EINVAL any use of reserved or struct padding.
Although we generally always do that, it's missed in two spots for
resource updates, one for the ring fd registration from this merge
window, and one for the extended arg. Make sure we have all of them
handled. (Dylan)
- A few fixes for the deferred file assignment (me, Pavel)
- Add a feature flag for the deferred file assignment so apps can tell
we handle it correctly (me)
- Fix a small perf regression with the current file position fix in
this merge window (me)
* tag 'io_uring-5.18-2022-04-14' of git://git.kernel.dk/linux-block:
io_uring: abort file assignment prior to assigning creds
io_uring: fix poll error reporting
io_uring: fix poll file assign deadlock
io_uring: use right issue_flags for splice/tee
io_uring: verify pad field is 0 in io_get_ext_arg
io_uring: verify resv is 0 in ringfd register/unregister
io_uring: verify that resv2 is 0 in io_uring_rsrc_update2
io_uring: move io_uring_rsrc_update2 validation
io_uring: fix assign file locking issue
io_uring: stop using io_wq_work as an fd placeholder
io_uring: move apoll->events cache
io_uring: io_kiocb_update_pos() should not touch file for non -1 offset
io_uring: flag the fact that linked file assignment is sane
Merge tag 'linux-kselftest-fixes-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"A mqueue perf test memory leak bug fix.
mq_perf_tests failed to call CPU_FREE to free memory allocated by
CPU_SET"
* tag 'linux-kselftest-fixes-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
testing/selftests/mqueue: Fix mq_perf_tests to free the allocated cpu set
Merge tag 'perf-tools-fixes-for-v5.18-2022-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- 'perf record --per-thread' mode doesn't have the CPU mask setup, so
it can use it to figure out the number of mmaps, fix it.
- Fix segfault accessing sample_id xyarray out of bounds, noticed while
using Intel PT where we have a dummy event to capture text poke perf
metadata events and we mixup the set of CPUs specified by the user
with the all CPUs map needed for text poke.
- Fix 'perf bench numa' to check if CPU used to bind task is online.
- Fix 'perf bench numa' usage of affinity for machines with more than
1000 CPUs.
- Fix misleading add event PMU debug message, noticed while using the
'intel_pt' PMU.
- Fix error check return value of hashmap__new() in 'perf stat', it
must use IS_ERR().
* tag 'perf-tools-fixes-for-v5.18-2022-04-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf bench: Fix numa bench to fix usage of affinity for machines with #CPUs > 1K
perf bench: Fix numa testcase to check if CPU used to bind task is online
perf record: Fix per-thread option
perf tools: Fix segfault accessing sample_id xyarray
perf stat: Fix error check return value of hashmap__new(), must use IS_ERR()
perf tools: Fix misleading add event PMU debug message
Merge tag 'nvme-5.18-2022-04-15' of git://git.infradead.org/nvme into block-5.18
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.18
- tone down the error logging added this merge window a bit
(Chaitanya Kulkarni)
- quirk devices with non-unique unique identifiers (me)"
* tag 'nvme-5.18-2022-04-15' of git://git.infradead.org/nvme:
nvme-pci: disable namespace identifiers for Qemu controllers
nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
nvme: add a quirk to disable namespace identifiers
nvme: don't print verbose errors for internal passthrough requests
nvme-pci: disable namespace identifiers for Qemu controllers
Qemu unconditionally reports a UUID, which depending on the qemu version
is either all-null (which is incorrect but harmless) or contains a single
bit set for all controllers. In addition it can also optionally report
a eui64 which needs to be manually set. Disable namespace identifiers
for Qemu controlles entirely even if in some cases they could be set
correctly through manual intervention.
Reported-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
The MAXIO MAP1002/1202 controllers reports completely bogus Namespace
identifiers that even change after suspend cycles. Disable using
the Identifiers entirely.
Reported-by: 金韬 <me@kingtous.cn> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Tested-by: 金韬 <me@kingtous.cn>
nvme: add a quirk to disable namespace identifiers
Add a quirk to disable using and exporting namespace identifiers for
controllers where they are broken beyond repair.
The most directly visible problem with non-unique namespace identifiers
is that they break the /dev/disk/by-id/ links, with the link for a
supposedly unique identifier now pointing to one of multiple possible
namespaces that share the same ID, and a somewhat random selection of
which one actually shows up.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
nvme: don't print verbose errors for internal passthrough requests
Use the RQF_QUIET flag to skip the newly added verbose error reporting,
and set the flag in __nvme_submit_sync_cmd, which is used for most
internal passthrough requests where we do expect errors (e.g. due to
probing for optional functionality). This is similar to what the SCSI
verbose error logging does.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Alan Adamson <alan.adamson@oracle.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Tested-by: Alan Adamson <alan.adamson@oracle.com> Tested-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
io_uring: abort file assignment prior to assigning creds
We need to either restore creds properly if we fail on the file
assignment, or just do the file assignment first instead. Let's do
the latter as it's simpler, should make no difference here for
file assignment.
Mike Snitzer [Thu, 14 Apr 2022 15:52:54 +0000 (11:52 -0400)]
dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
The intent behind commit 17737b8c33a7 ("dm: flag clones created by
__send_duplicate_bios") was to formally disallow the use of
dm_accept_partial_bio() where it simply isn't possible -- due to
constraint that multiple bios cannot meaningfully update a shared
tio->len_ptr.
But that commit went too far and disallowed the case where "abormal"
IO (e.g. WRITE_ZEROES) is only using a single bio. Fix this by
not marking a dm_io with a single dm_target_io (and bio), that happens
to be created by __send_duplicate_bios, as DM_TIO_IS_DUPLICATE_BIO.
Also remove 'unsigned *len' parameter from alloc_multiple_bios().
This commit fixes a dm_accept_partial_bio() BUG_ON() with dm-zoned
when a WRITE_ZEROES bio is issued.
Fixes: 6ff7b693e3ae ("dm: switch dm_target_io booleans over to proper flags") Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
amdgpu:
- Fix for alpha properly in pre-multiplied mode
- Fix VCN 3.1.2 firmware name
- Suspend/resume fix
- Add a gfxoff quirk for Mac vega20 board
- DCN 3.1.6 spread spectrum fix"
* tag 'drm-fixes-2022-04-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: remove dtbclk_ss compensation for dcn316
drm/amdgpu: Enable gfxoff quirk on MacBook Pro
drm/amdgpu: Ensure HDA function is suspended before ASIC reset
drm/amdgpu: fix VCN 3.1.2 firmware name
drm/amd/display: don't ignore alpha property on pre-multiplied mode
drm/msm/gpu: Avoid -Wunused-function with !CONFIG_PM_SLEEP
drm/msm/dp: add fail safe mode outside of event_mutex context
drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
drm/msm: Stop using iommu_present()
drm/msm/mdp5: check the return of kzalloc()
drm/msm: Fix range size vs end confusion
drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
drm/msm/dpu: Use indexed array initializer to prevent mismatches
drm/msm/disp: check the return value of kzalloc()
dt-bindings: display/msm: another fix for the dpu-qcm2290 example
drm/msm: Add missing put_task_struct() in debugfs path
drm/msm/gpu: Remove mutex from wait_event condition
drm/msm/gpu: Park scheduler threads for system suspend
drm/msm/gpu: Rename runtime suspend/resume functions
Merge tag '5.18-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
- two fixes related to unmount
- symlink overflow fix
- minor netfs fix
- improved tracing for crediting (flow control)
* tag '5.18-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: verify that tcon is valid before dereference in cifs_kill_sb
cifs: potential buffer overflow in handling symlinks
cifs: Split the smb3_add_credits tracepoint
cifs: release cached dentries only if mount is complete
cifs: Check the IOCB_DIRECT flag, not O_DIRECT
When asked to create a path ending '/', but which is not to be a
directory (LOOKUP_DIRECTORY not set), filename_create() will never try
to create the file. If it doesn't exist, -ENOENT is reported.
However, it still passes LOOKUP_CREATE|LOOKUP_EXCL to the filesystems
->lookup() function, even though there is no intent to create. This is
misleading and can cause incorrect behaviour.
If you try
ln -s foo /path/dir/
where 'dir' is a directory on an NFS filesystem which is not currently
known in the dcache, this will fail with ENOENT.
But as the name is not in the dcache, nfs_lookup gets called with
LOOKUP_CREATE|LOOKUP_EXCL and so it returns NULL without performing any
lookup, with the expectation that a subsequent call to create the target
will be made, and the lookup can be combined with the creation. In the
case with a trailing '/' and no LOOKUP_DIRECTORY, that call is never
made. Instead filename_create() sees that the dentry is not (yet)
positive and returns -ENOENT - even though the directory actually
exists.
So only set LOOKUP_CREATE|LOOKUP_EXCL if there really is an intent to
create, and use the absence of these flags to decide if -ENOENT should
be returned.
Note that filename_parentat() is only interested in LOOKUP_REVAL, so we
split that out and store it in 'reval_flag'. __lookup_hash() then gets
reval_flag combined with whatever create flags were determined to be
needed.
Reviewed-by: David Disseldorp <ddiss@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: NeilBrown <neilb@suse.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rob Herring [Wed, 13 Apr 2022 14:00:15 +0000 (09:00 -0500)]
dt-bindings: display: panel-timing: Define a single type for properties
It's not good practice to define multiple types for the same property, so
factor out the type reference making the properties always an uint32-array
with a length of 1 or 3 items.
The Gemini defconfig needs to be updated due to DSA driver
Kconfig changes in the v5.18 merge window:
CONFIG_NET_DSA_REALTEK_SMI is now behind
CONFIG_NET_DSA_REALTEK and the desired DSA switch need
to be selected explicitly with
CONFIG_NET_DSA_REALTEK_RTL8366RB.
Take this opportunity to update some other minor config
options:
- CONFIG_MARVELL_PHY moved around because of Kconfig
changes.
- CONFIG_SENSORS_DRIVETEMP should be selected since is
regulates the system critical alert temperature on
some devices, which is nice if it is handled even
if initramfs or root fails to mount.
Fixes: f938a011e265 ("net: dsa: realtek-smi: move to subdirectory") Fixes: 5f47fb4940dd ("net: dsa: realtek: convert subdrivers into modules") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Thu, 7 Apr 2022 22:52:54 +0000 (17:52 -0500)]
arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzk+dt@kernel.org> Cc: linux-arm-msm@vger.kernel.org Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rob Herring [Thu, 7 Apr 2022 22:51:07 +0000 (17:51 -0500)]
ARM: dts: Fix more boolean properties with values
Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.
It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Krzysztof Kozlowski <krzk+dt@kernel.org> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: "Benoît Cousson" <bcousson@baylibre.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-arm-msm@vger.kernel.org Link: https://lore.kernel.org/r/20220407225107.2175958-1-robh@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge tag 's390-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Heiko Carstens:
- Convert current_stack_pointer to a register alias like it is assumed
if ARCH_HAS_CURRENT_STACK_POINTER is selected. The existing
implementation as a function breaks CONFIG_HARDENED_USERCOPY
sanity-checks
- Get rid of -Warray-bounds warning within kexec code
- Add minimal IBM z16 support by reporting a proper elf platform, and
adding compile options
- Update defconfigs
* tag 's390-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: enable CONFIG_HARDENED_USERCOPY in debug_defconfig
s390: current_stack_pointer shouldn't be a function
s390: update defconfigs
s390/kexec: silence -Warray-bounds warning
s390: allow to compile with z16 optimizations
s390: add z16 elf platform
Merge tag 'net-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from wireless and netfilter.
Current release - regressions:
- smc: fix af_ops of child socket pointing to released memory
- wifi: ath9k: fix usage of driver-private space in tx_info
Previous releases - regressions:
- ipv6: fix panic when forwarding a pkt with no in6 dev
- sctp: use the correct skb for security_sctp_assoc_request
- smc: fix NULL pointer dereference in smc_pnet_find_ib()
- sched: fix initialization order when updating chain 0 head
- phy: don't defer probe forever if PHY IRQ provider is missing
- dsa: revert "net: dsa: setup master before ports"
- dsa: felix: fix tagging protocol changes with multiple CPU ports
- eth: ice:
- fix use-after-free when freeing @rx_cpu_rmap
- revert "iavf: fix deadlock occurrence during resetting VF
interface"
- eth: lan966x: stop processing the MAC entry is port is wrong
Previous releases - always broken:
- sched:
- flower: fix parsing of ethertype following VLAN header
- taprio: check if socket flags are valid
- nfc: add flush_workqueue to prevent uaf
- veth: ensure eth header is in skb's linear part
- eth: stmmac: fix altr_tse_pcs function when using a fixed-link
- eth: macb: restart tx only if queue pointer is lagging
- eth: macvlan: fix leaking skb in source mode with nodst option"
* tag 'net-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
rtnetlink: Fix handling of disabled L3 stats in RTM_GETSTATS replies
net: dsa: felix: fix tagging protocol changes with multiple CPU ports
tun: annotate access to queue->trans_start
nfc: nci: add flush_workqueue to prevent uaf
net: dsa: realtek: don't parse compatible string for RTL8366S
net: dsa: realtek: fix Kconfig to assure consistent driver linkage
net: ftgmac100: access hardware register after clock ready
Revert "net: dsa: setup master before ports"
macvlan: Fix leaking skb in source mode with nodst option
netfilter: nf_tables: nft_parse_register can return a negative value
net: lan966x: Stop processing the MAC entry is port is wrong.
net: lan966x: Fix when a port's upper is changed.
net: lan966x: Fix IGMP snooping when frames have vlan tag
net: lan966x: Update lan966x_ptp_get_nominal_value
sctp: Initialize daddr on peeled off socket
net/smc: Fix af_ops of child socket pointing to released memory
net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
net/smc: use memcpy instead of snprintf to avoid out of bounds read
net: macb: Restart tx only if queue pointer is lagging
...
Merge tag 'sound-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became an unexpectedly large pull request due to various
regression fixes in the previous kernels.
The majority of fixes are a series of patches to address the
regression at probe errors in devres'ed drivers, while there are yet
more fixes for the x86 SG allocations and for USB-audio buffer
management. In addition, a few HD-audio quirks and other small fixes
are found"
* tag 'sound-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (52 commits)
ALSA: usb-audio: Limit max buffer and period sizes per time
ALSA: memalloc: Add fallback SG-buffer allocations for x86
ALSA: nm256: Don't call card private_free at probe error path
ALSA: mtpav: Don't call card private_free at probe error path
ALSA: rme9652: Fix the missing snd_card_free() call at probe error
ALSA: hdspm: Fix the missing snd_card_free() call at probe error
ALSA: hdsp: Fix the missing snd_card_free() call at probe error
ALSA: oxygen: Fix the missing snd_card_free() call at probe error
ALSA: lx6464es: Fix the missing snd_card_free() call at probe error
ALSA: cmipci: Fix the missing snd_card_free() call at probe error
ALSA: aw2: Fix the missing snd_card_free() call at probe error
ALSA: als300: Fix the missing snd_card_free() call at probe error
ALSA: lola: Fix the missing snd_card_free() call at probe error
ALSA: bt87x: Fix the missing snd_card_free() call at probe error
ALSA: sis7019: Fix the missing error handling
ALSA: intel_hdmi: Fix the missing snd_card_free() call at probe error
ALSA: via82xx: Fix the missing snd_card_free() call at probe error
ALSA: sonicvibes: Fix the missing snd_card_free() call at probe error
ALSA: rme96: Fix the missing snd_card_free() call at probe error
ALSA: rme32: Fix the missing snd_card_free() call at probe error
...
Rob Herring [Wed, 13 Apr 2022 14:01:21 +0000 (09:01 -0500)]
dt-bindings: Fix array constraints on scalar properties
Scalar properties shouldn't have array constraints (minItems, maxItems,
items). These constraints can simply be dropped with any constraints under
'items' moved up a level.
Cc: Agathe Porte <agathe.porte@nokia.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jean Delvare <jdelvare@suse.com> Cc: Krzysztof Kozlowski <krzk+dt@kernel.org> Cc: Olivier Moysan <olivier.moysan@foss.st.com> Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Cc: Yunfei Dong <yunfei.dong@mediatek.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: linux-hwmon@vger.kernel.org Cc: alsa-devel@alsa-project.org Cc: linux-iio@vger.kernel.org Cc: linux-media@vger.kernel.org Cc: linux-remoteproc@vger.kernel.org Cc: linux-spi@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Mark Brown <broonie@kernel.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20220413140121.3132837-1-robh@kernel.org
Merge tag 'for-5.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more code and warning fixes.
There's one feature ioctl removal patch slated for 5.18 that did not
make it to the main pull request. It's just a one-liner and the ioctl
has a v2 that's in use for a long time, no point to postpone it to
5.19.
Late update:
- remove balance v1 ioctl, superseded by v2 in 2012
Fixes:
- add back cgroup attribution for compressed writes
- add super block write start/end annotations to asynchronous balance
- fix root reference count on an error handling path
- in zoned mode, activate zone at the chunk allocation time to avoid
ENOSPC due to timing issues
- fix delayed allocation accounting for direct IO
Warning fixes:
- simplify assertion condition in zoned check
- remove an unused variable"
* tag 'for-5.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix btrfs_submit_compressed_write cgroup attribution
btrfs: fix root ref counts in error handling in btrfs_get_root_ref
btrfs: zoned: activate block group only for extent allocation
btrfs: return allocated block group from do_chunk_alloc()
btrfs: mark resumed async balance as writing
btrfs: remove support of balance v1 ioctl
btrfs: release correct delalloc amount in direct IO write path
btrfs: remove unused variable in btrfs_{start,write}_dirty_block_groups()
btrfs: zoned: remove redundant condition in btrfs_run_delalloc_range
Merge tag 'fscache-fixes-20220413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache fixes from David Howells:
"Here's a collection of fscache and cachefiles fixes and misc small
cleanups. The two main fixes are:
- Add a missing unmark of the inode in-use mark in an error path.
- Fix a KASAN slab-out-of-bounds error when setting the xattr on a
cachefiles volume due to the wrong length being given to memcpy().
In addition, there's the removal of an unused parameter, removal of an
unused Kconfig option, conditionalising a bit of procfs-related stuff
and some doc fixes"
* tag 'fscache-fixes-20220413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
fscache: remove FSCACHE_OLD_API Kconfig option
fscache: Use wrapper fscache_set_cache_state() directly when relinquishing
fscache: Move fscache_cookies_seq_ops specific code under CONFIG_PROC_FS
fscache: Remove the cookie parameter from fscache_clear_page_bits()
docs: filesystems: caching/backend-api.rst: fix an object withdrawn API
docs: filesystems: caching/backend-api.rst: correct two relinquish APIs use
cachefiles: Fix KASAN slab-out-of-bounds in cachefiles_set_volume_xattr
cachefiles: unmark inode in use in error path
bind_to_node() uses "sched_getaffinity" to save the original cpumask and
this call is returning EINVAL ((invalid argument).
This happens because the default mask size in glibc is 1024. To
overcome this 1024 CPUs mask size limitation of cpu_set_t, change the
mask size using the CPU_*_S macros ie, use CPU_ALLOC to allocate
cpumask, CPU_ALLOC_SIZE for size.
Apart from fixing this for "orig_mask", apply same logic to "mask" as
well which is used to setaffinity so that mask size is large enough to
represent number of possible CPU's in the system.
sched_getaffinity is used in one more place in perf numa bench. It is in
"bind_to_cpu" function. Apply the same logic there also. Though
currently no failure is reported from there, it is ideal to change
getaffinity to work with such system configurations having CPU's more
than default mask size supported by glibc.
Also fix "sched_setaffinity" to use mask size which is large enough to
represent number of possible CPU's in the system.
Fixed all places where "bind_cpumask" which is part of "struct
thread_data" is used such that bind_cpumask works in all configuration.
Reported-by: Disha Goel <disgoel@linux.vnet.ibm.com> Signed-off-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nageswara R Sastry <rnsastry@linux.ibm.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: linuxppc-dev@lists.ozlabs.org Link: https://lore.kernel.org/r/20220412164059.42654-3-atrajeev@linux.vnet.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The Testcases uses CPU's 0 and 8. In function "parse_setup_cpu_list",
There is check to see if cpu number is greater than max cpu's possible
in the system ie via "if (bind_cpu_0 >= g->p.nr_cpus || bind_cpu_1 >=
g->p.nr_cpus) {".
But it could happen that system has say 48 CPU's, but only number of
online CPU's is 0-7. Other CPU's are offlined. Since "g->p.nr_cpus" is
48, so function will go ahead and set bit for CPU 8 also in cpumask (
td->bind_cpumask).
bind_to_cpumask function is called to set affinity using
sched_setaffinity and the cpumask. Since the CPU8 is not present, set
affinity will fail here with EINVAL.
Fix this issue by adding a check to make sure that, CPU's provided in
the input argument values are online before proceeding further and skip
the test. For this, include new helper function "is_cpu_online" in
"tools/perf/util/header.c".
Since "BIT(x)" definition will get included from header.h, remove
that from bench/numa.c
Jeremy Linton [Tue, 12 Apr 2022 21:04:20 +0000 (16:04 -0500)]
net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
It turns out after digging deeper into this bug, that it was being
triggered by GCC12 failing to call the bcmgenet_enable_dma()
routine. Given that a gcc12 fix has been merged [1] and the genet
driver now works properly when built with gcc12, this commit should
be reverted.
Petr Machata [Tue, 12 Apr 2022 20:25:06 +0000 (22:25 +0200)]
rtnetlink: Fix handling of disabled L3 stats in RTM_GETSTATS replies
When L3 stats are disabled, rtnl_offload_xstats_get_size_stats() returns
size of 0, which is supposed to be an indication that the corresponding
attribute should not be emitted. However, instead, the current code
reserves a 0-byte attribute.
The reason this does not show up as a citation on a kasan kernel is that
netdev_offload_xstats_get(), which is supposed to fill in the data, never
ends up getting called, because rtnl_offload_xstats_get_stats() notices
that the stats are not actually used and skips the call.
Thus a zero-length IFLA_OFFLOAD_XSTATS_L3_STATS attribute ends up in a
response, confusing the userspace.
Fix by skipping the L3-stats related block in rtnl_offload_xstats_fill().
Vladimir Oltean [Tue, 12 Apr 2022 17:22:09 +0000 (20:22 +0300)]
net: dsa: felix: fix tagging protocol changes with multiple CPU ports
When the device tree has 2 CPU ports defined, a single one is active
(has any dp->cpu_dp pointers point to it). Yet the second one is still a
CPU port, and DSA still calls ->change_tag_protocol on it.
On the NXP LS1028A, the CPU ports are ports 4 and 5. Port 4 is the
active CPU port and port 5 is inactive.
traffic is now broken, because the driver has moved the NPI port from
port 4 to port 5, unbeknown to DSA.
The problem can be avoided by detecting that the second CPU port is
unused, and not doing anything for it. Further rework will be needed
when proper support for multiple CPU ports is added.
Treat this as a bug and prepare current kernels to work in single-CPU
mode with multiple-CPU DT blobs.
Antoine Tenart [Tue, 12 Apr 2022 13:58:52 +0000 (15:58 +0200)]
tun: annotate access to queue->trans_start
Commit 1db7b89a838a ("net: annotate accesses to queue->trans_start")
introduced a new helper, txq_trans_cond_update, to update
queue->trans_start using WRITE_ONCE. One snippet in drivers/net/tun.c
was missed, as it was introduced roughly at the same time.
Fixes: 1db7b89a838a ("net: annotate accesses to queue->trans_start") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Antoine Tenart <atenart@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220412135852.466386-1-atenart@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ronnie Sahlberg [Wed, 13 Apr 2022 00:02:17 +0000 (10:02 +1000)]
cifs: verify that tcon is valid before dereference in cifs_kill_sb
On umount, cifs_sb->tlink_tree might contain entries that do not represent
a valid tcon.
Check the tcon for error before we dereference it.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Reported-by: Xiaoli Feng <xifeng@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com>
dma-direct: avoid redundant memory sync for swiotlb
When we looked into FIO performance with swiotlb enabled in VM, we found
swiotlb_bounce() is always called one more time than expected for each DMA
read request.
It turns out that the bounce buffer is copied to original DMA buffer twice
after the completion of a DMA request (one is done by in
dma_direct_sync_single_for_cpu(), the other by swiotlb_tbl_unmap_single()).
But the content in bounce buffer actually doesn't change between the two
rounds of copy. So, one round of copy is redundant.
Pass DMA_ATTR_SKIP_CPU_SYNC flag to swiotlb_tbl_unmap_single() to
skip the memory copy in it.
This fix increases FIO 64KB sequential read throughput in a guest with
swiotlb=force by 5.6%.
Fixes: e090aad6eb58 ("dma-direct: merge swiotlb_dma_ops into the dma_direct code") Reported-by: Wang Zhaoyang1 <zhaoyang1.wang@intel.com> Reported-by: Gao Liang <liang.gao@intel.com> Signed-off-by: Chao Gao <chao.gao@intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Charlene Liu [Wed, 30 Mar 2022 19:25:00 +0000 (15:25 -0400)]
drm/amd/display: remove dtbclk_ss compensation for dcn316
[why]
dcn316's dtbclk is from non_ss clock source.
no compensation required here.
Reviewed-by: Chris Park <Chris.Park@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Charlene Liu <Charlene.Liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / kernel.git / log