Simon Glass [Sun, 23 Jan 2022 14:04:08 +0000 (07:04 -0700)]
video: Drop references to CONFIG_VIDEO et al
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Han Xu [Fri, 25 Mar 2022 13:36:38 +0000 (08:36 -0500)]
mtd: gpmi: fix the bch setting backward compatible issue
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 9675a86c0b (mtd: gpmi: provide the option to use legacy bch geometry) Fixes: 5045027531 (mtd: gpmi: change the BCH layout setting for large oob NAND) Tested-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Han Xu <han.xu@nxp.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mark Kettenis [Mon, 21 Mar 2022 21:41:18 +0000 (22:41 +0100)]
arm: apple: Fix mem layout
The current approach for setting the environment variables that
describe the memory layout runs the risk of overlapping with
reserved memory regions. Use the lmb code to derive the addresses
for these variables instead.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Up to now the initrddump.efi application has drained the input after
showing the prompt. This works for humans but leads to problems when
automating testing. If the input is drained, this should be done before
showing the prompt.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_loader: nocolor command line attr for initrddump.efi
initrddump.efi uses colored output and clear the screen. This is not
helpful for integration into Python tests. Allow specifying 'nocolor' in
the load option data to suppress color output and clearing the screen.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Andre Przywara [Tue, 15 Mar 2022 23:20:54 +0000 (23:20 +0000)]
sunxi: dts: Update RGMII phy-mode properties
Commit a24fed01fe99 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org>
Andre Przywara [Tue, 15 Mar 2022 00:00:53 +0000 (00:00 +0000)]
sunxi: Fix old GMAC pinmux setup
Commit db9a2b7c1a93 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Billy Tsai [Tue, 8 Mar 2022 03:04:07 +0000 (11:04 +0800)]
ARM: dts: ast2600: Add PWM to device tree
Add the PWM node and enable it for AST2600 EVB
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Billy Tsai [Tue, 8 Mar 2022 03:04:06 +0000 (11:04 +0800)]
pinctrl: Add the pinctrl setting for PWM.
This patchs add the signal description array for PWM pinctrl settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Billy Tsai [Tue, 8 Mar 2022 03:04:05 +0000 (11:04 +0800)]
pwm: Add Aspeed ast2600 PWM support
This patch add the support of PWM controller which can be found at aspeed
ast2600 soc. The pwm supoorts up to 16 channels and it's part function
of multi-function device "pwm-tach controller".
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Pali Rohár [Fri, 18 Feb 2022 12:16:19 +0000 (13:16 +0100)]
pci: Remove duplicate PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* macros
Macros PCI_CLASS_CODE_* and PCI_CLASS_SUB_CODE_* are unused and are
duplication of PCI_CLASS_* macros defined in pci_ids.h header file.
So remove them.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 18 Feb 2022 12:16:18 +0000 (13:16 +0100)]
sandbox: video: Replace PCI_CLASS_* macros by one from pci_ids.h
Replace old macros PCI_CLASS_CODE_COMM and PCI_CLASS_SUB_CODE_COMM_SERIAL
by new macros defined in pci_ids.h. Old macros would be deleted in followup
commit.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Sean Anderson [Tue, 22 Feb 2022 17:19:25 +0000 (12:19 -0500)]
Add option to use -Og
This adds support for using -Og when building U-Boot. According to the
gcc man page:
> -Og should be the optimization level of choice for the standard
> edit-compile-debug cycle, offering a reasonable level of optimization
> while maintaining fast compilation and a good debugging experience.
This optimization level is roughly -O1 minus a few additional
optimizations. It provides a noticably better debugging experience, with
many fewer variables <optimized out>.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Sean Anderson [Tue, 22 Feb 2022 17:19:24 +0000 (12:19 -0500)]
Split CONFIG_CC_OPTIMIZE_FOR_SIZE into two configs
This adds a separate CONFIG_CC_OPTIMIZE_FOR_SPEED option in a choice,
in preparation for adding another optimization option. Also convert SH's
makefile to use this new option.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Wed, 23 Mar 2022 16:19:42 +0000 (17:19 +0100)]
arm: a37xx: espressobin: Fix non-working SPI
Commit 3fc8dc735f22 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 3fc8dc735f22 ("arm: a37xx: Update DTS files to version from upstream Linux kernel") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Tue, 22 Mar 2022 16:17:59 +0000 (17:17 +0100)]
arm: mvebu: dts: turris_mox: fix non-working USB port
Commit 3fc8dc735f22 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 3fc8dc735f22 ("arm: a37xx: Update DTS files to version from upstream Linux kernel") Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Vasut [Wed, 16 Feb 2022 14:27:59 +0000 (15:27 +0100)]
cmd: eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled
With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com> Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tom Rini [Sun, 20 Mar 2022 19:14:59 +0000 (15:14 -0400)]
Merge tag 'efi-2022-04-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Alexander Graf [Sun, 27 Feb 2022 12:18:56 +0000 (13:18 +0100)]
efi_loader: Ignore DT when ACPI is on
For targets that enable ACPI, we should not pass Device Trees into
the payload. However, our distro boot logic always passes the builtin
DT as an argument.
To make it easy to use ACPI with distro boot, let's just ignore the DT
argument to bootefi when ACPI is enabled. That way, we can successfully
distro boot payloads on ACPI enabled targets.
Signed-off-by: Alexander Graf <agraf@csgraf.de> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Simon Glass [Sun, 6 Mar 2022 03:19:12 +0000 (20:19 -0700)]
binman: Support splitting an ELF file into multiple nodes
Some boards need to load an ELF file using the 'loadables' property, but
the file has segments at different memory addresses. This means that it
cannot be supplied as a flat binary.
Allow generating a separate node in the FIT for each segment in the ELF,
with a different load address for each.
Also add checks that the fit,xxx directives are valid.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:11 +0000 (20:19 -0700)]
binman: Keep a separate list of entries for fit
The current implementation sets up the FIT entries but then deletes the
'generator' ones so they don't appear in the final image.
This is a bit clumsy. We cannot build the image more than once, since the
generator entries are lost during the first build. Binman requires that
calling BuildSectionData() multiple times returns a valid result each
time.
Keep a separate, private list which includes the generator nodes and use
that where needed, to correct this problem. Ensure that the missing list
includes removed generator entries too.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:10 +0000 (20:19 -0700)]
binman: Update fit to use node instead of subnode
It doesn't make sense to use 'subnode' as a function parameter since it
is just a 'node' so far as the function is concerned. Update two functions
to use 'node' instead.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:09 +0000 (20:19 -0700)]
binman: Add a consistent way to report errors with fit
Add a new function to handling reporting errors within a particular
subnode of the FIT description. This can be used to make the format of
these errors consistent.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:06 +0000 (20:19 -0700)]
binman: Read the fit entries only once
At present the entries are read twice, once by the entry_Section class
and once by the FIT implementation. This is harmless but can be confusing
when debugging. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:04 +0000 (20:19 -0700)]
binman: Make fake blobs zero-sized by default
On x86 devices having even a small amount of data can cause an overlap
between regions. For example, bayleybay complains when the intel-vga
region overlaps with u-boot-ucode:
Simon Glass [Sun, 6 Mar 2022 03:19:03 +0000 (20:19 -0700)]
binman: Change how faked blobs are created
At present fake blobs are created but internally an empty blob is used.
Change it to use the contents of the faked file. Also return whether the
blob was faked, in case the caller needs to know that.
Add a TODO to put fake blobs in their own directory.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:01 +0000 (20:19 -0700)]
binman: Refactor fit to generate output at the end
At present the fit implementation creates the output tree while
scanning the FIT description. Then it updates the tree later when the
data is known.
This works, but is a bit confusing, since it requires mixing the scanning
code with the generation code, with a fix-up step at the end.
It is actually possible to do this in two phases, one to scan everything
and the other to generate the FIT. Thus the FIT is generated in one pass,
when everything is known.
Update the code accordingly. The only functional change is that the 'data'
property for each node are now last instead of first, which is really a
more natural position. Update the affected test to deal with this.
One wrinkle is that the calculated properties (image-pos, size and offset)
are now added before the FIT is generated. so we must filter these out
when copying properties from the binman description to the FIT.
Most of the change here is splitting out some of the code from the
ReadEntries() implementation into _BuildInput(). So despite the large
diff, most of the code is the same. It is not feasible to split this patch
up, so far as I can tell.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:19:00 +0000 (20:19 -0700)]
binman: Rename ExpandEntries to gen_entries
Leave the 'expand' term for use by entry types which have an expanded
version of themselves. Rename this method to indicate that it generates
subentries.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Mar 2022 03:18:59 +0000 (20:18 -0700)]
binman: Rename ExpandToLimit to extend_to_limit
The word 'expand' is used for entries which generate subentries. It is
also used for entries that can have an '_expanded' version which is used
to break out its contents.
Rather than talking about expanding an entry's size, use the term
'extending'. It is slightly more precise and avoids the above conflicts.
This change renders the old 'expand-size' property invalid, so add an
error check for that.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
projects / uboot.git / log