Russell King [Mon, 9 Dec 2019 14:16:00 +0000 (14:16 +0000)]
net: sfp: rename sm_retries
Rename sm_retries as sm_fault_retries, as this is what this member is
tracking.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 9 Dec 2019 14:15:55 +0000 (14:15 +0000)]
net: sfp: use a definition for the fault recovery attempts
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 11 Dec 2019 19:53:42 +0000 (11:53 -0800)]
Merge branch 'sfp-copper-modules'
Russell King says:
====================
Add support for SFP+ copper modules
This series adds support for Copper SFP+ modules with Clause 45 PHYs.
Specifically the patches:
1. drop support for the probably never tested 100BASE-*X modules.
2. drop EEPROM ID from sfp_select_interface()
3. add more compliance code definitions from SFF-8024, renaming the
existing definitions.
4. add module start/stop methods so phylink knows when a module is
about to become active. The module start method is called after
we have probed for a PHY on the module.
5. move start/stop of module PHY down into phylink using the new
module start/stop methods.
6. add support for Clause 45 I2C accesses, tested with Methode DM7052.
Other modules appear to use the same protocol, but slight
differences, but I do not have those modules to test with.
(if someone does, please holler!)
7. rearrange how we attach to PHYs so that we can support Clause 45
PHYs with indeterminant interface modes. (Clause 45 PHYs appear
to like to change their PHY interface mode depending on the
negotiated speed.)
8. add support for phylink to connect to a clause 45 PHY on a SFP
module.
9. split the link_an_mode between the configured value and the
currently selected mode value; some clause 45 PHYs have no
capability to provide in-band negotiation.
10. split the link configuration on SFP module insertion in phylink
so we can use it in other code paths.
11. delay MAC configuration for copper modules without a PHY to the
module start method - after any module PHY has been probed. If
the module has a PHY, then we setup the MAC when the PHY is
detected.
12. the Broadcom 84881 PHY does not support in-band negotiation even
though it uses SGMII and 2500BASE-X. Having the MAC operating
with in-band negotiation enabled, even with AN bypass enabled,
results in no link - Broadcom say that the host MAC must always
be forced.
13. add support for the Broadcom 84881 PHY found on the Methode
DM7052 module.
14. add support to SFP to probe for a Clause 45 PHY on copper SFP+
modules.
v3: now bisectable!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:57:01 +0000 (10:57 +0000)]
net: sfp: add support for Clause 45 PHYs
Some SFP+ modules have a Clause 45 PHY onboard, which is accessible via
the normal I2C address. Detect 10G BASE-T PHYs which may have an
accessible PHY and probe for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:56 +0000 (10:56 +0000)]
net: phy: add Broadcom BCM84881 PHY driver
Add a rudimentary Clause 45 driver for the BCM84881 PHY, found on
Methode DM7052 SFPs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:50 +0000 (10:56 +0000)]
net: phylink: make Broadcom BCM84881 based SFPs work
The Broadcom BCM84881 does not appear to send the SGMII control word
when operating in SGMII mode, which causes network adapters to fail
to link with the PHY, or decide to operate at fixed 1G speed, even if
the PHY negotiated 100M.
Work around this by detecting the Broadcom BCM84881 and switch to phy
mode rather than inband mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:45 +0000 (10:56 +0000)]
net: phylink: delay MAC configuration for copper SFP modules
Knowing whether we need to delay the MAC configuration because a module
may have a PHY is useful to phylink to allow NBASE-T modules to work on
systems supporting no more than 2.5G speeds.
This commit allows us to delay such configuration until after the PHY
has been probed by recording the parsed capabilities, and if the module
may have a PHY, doing no more until the module_start() notification is
called. At that point, we either have a PHY, or we don't.
We move the PHY-based setup a little later, and use the PHYs support
capabilities rather than the EEPROM parsed capabilities to determine
whether we can support the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:40 +0000 (10:56 +0000)]
net: phylink: split phylink_sfp_module_insert()
Split out the configuration step from phylink_sfp_module_insert() so
we can re-use this later.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:35 +0000 (10:56 +0000)]
net: phylink: split link_an_mode configured and current settings
Split link_an_mode between the configured setting and the current
operating setting. This is an important distinction to make when we
need to configure PHY mode for a plugged SFP+ module that does not
use in-band signalling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:30 +0000 (10:56 +0000)]
net: phylink: support Clause 45 PHYs on SFP+ modules
Some SFP+ modules have Clause 45 PHYs embedded on them, which need a
little more handling in order to ensure that they are correctly setup,
as they switch the PHY link mode according to the negotiated speed.
With Clause 22 PHYs, we assumed that they would operate in SGMII mode,
but this assumption is now false. Adapt phylink to support Clause 45
PHYs on SFP+ modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:25 +0000 (10:56 +0000)]
net: phylink: re-split __phylink_connect_phy()
In order to support Clause 45 PHYs on SFP+ modules, which have an
indeterminant phy interface mode, we need to be able to call
phylink_bringup_phy() with a different interface mode to that used when
binding the PHY. Reduce __phylink_connect_phy() to an attach operation,
and move the call to phylink_bringup_phy() to its call sites.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:20 +0000 (10:56 +0000)]
net: mdio-i2c: add support for Clause 45 accesses
Some SFP+ modules have PHYs on them just like SFP modules do, except
they are Clause 45 PHYs. The I2C protocol used to access them is
modified slightly in order to send the device address and 16-bit
register index.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:14 +0000 (10:56 +0000)]
net: sfp: move phy_start()/phy_stop() to phylink
Move phy_start() and phy_stop() into the module_start and module_stop
notifications in phylink, rather than having them in the SFP code.
This gives phylink responsibility for controlling the PHY, rather
than having SFP start and stop the PHY state machine.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with some copper modules, we can't positively know the
module capabilities are until we have probed the PHY. Without the full
capabilities, we may end up failing a module that we could otherwise
drive with a restricted set of capabilities.
An example of this would be a module with a NBASE-T PHY plugged into
a host that supports phy interface modes 2500BASE-X and SGMII. The
PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes,
which means a subset of the capabilities are compatible with the host.
However, reading the module EEPROM leads us to believe that the module
only supports ethtool link mode 10GBASE-T, which is incompatible with
the host - and thus results in the module being rejected.
This patch adds an extra notification which are triggered after the
SFP module's PHY probe, and a corresponding notification just before
the PHY is removed.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:56:04 +0000 (10:56 +0000)]
net: sfp: add more extended compliance codes
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications. Split these constants from the enum, and
rename them to indicate that they're defined by SFF-8024.
Add and use updated SFF-8024 extended compliance code definitions for
10GBASE-T, 5GBASE-T and 2.5GBASE-T modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:55:59 +0000 (10:55 +0000)]
net: sfp: derive interface mode from ethtool link modes
We don't need the EEPROM ID to derive the phy interface mode as we can
derive it merely from the ethtool link modes. Remove the EEPROM ID
argument to sfp_select_interface().
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 11 Dec 2019 10:55:54 +0000 (10:55 +0000)]
net: sfp: remove incomplete 100BASE-FX and 100BASE-LX support
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this
is probably an incorrect assumption. In any case, sfp_parse_support()
will fail such a module. Let's stop pretending we support these
modules.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
T6 has a separate region known as high priority filter region
that allows classifying packets going through ULD path. So,
query firmware for HPFILTER resources and enable the high
priority offload filter support when it is available.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen Wandun [Tue, 10 Dec 2019 10:24:50 +0000 (18:24 +0800)]
enetc: remove variable 'tc_max_sized_frame' set but not used
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]
Fixes: c431047c4efe ("enetc: add support Credit Based Shaper(CBS) for hardware offload") Signed-off-by: Chen Wandun <chenwandun@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 10 Dec 2019 05:04:01 +0000 (21:04 -0800)]
nfp: add support for TLV device stats
Device stats are currently hard coded in the PCI BAR0 layout.
Add a ability to read them from the TLV area instead.
Names for the stats are maintained by the driver, and their
meaning documented. This allows us to more easily add and
remove device stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: Cleanup duplicate initialization of sk->sk_state.
When a TCP socket is created, sk->sk_state is initialized twice as
TCP_CLOSE in sock_init_data() and tcp_init_sock(). The tcp_init_sock() is
always called after the sock_init_data(), so it is not necessary to update
sk->sk_state in the tcp_init_sock().
Before v2.1.8, the code of the two functions was in the inet_create(). In
the patch of v2.1.8, the tcp_v4/v6_init_sock() were added and the code of
initialization of sk->state was duplicated.
Signed-off-by: Kuniyuki Iwashima <kuni1840@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Mon, 9 Dec 2019 23:52:46 +0000 (00:52 +0100)]
tipc: introduce variable window congestion control
We introduce a simple variable window congestion control for links.
The algorithm is inspired by the Reno algorithm, covering both 'slow
start', 'congestion avoidance', and 'fast recovery' modes.
- We introduce hard lower and upper window limits per link, still
different and configurable per bearer type.
- We introduce a 'slow start theshold' variable, initially set to
the maximum window size.
- We let a link start at the minimum congestion window, i.e. in slow
start mode, and then let is grow rapidly (+1 per rceived ACK) until
it reaches the slow start threshold and enters congestion avoidance
mode.
- In congestion avoidance mode we increment the congestion window for
each window-size number of acked packets, up to a possible maximum
equal to the configured maximum window.
- For each non-duplicate NACK received, we drop back to fast recovery
mode, by setting the both the slow start threshold to and the
congestion window to (current_congestion_window / 2).
- If the timeout handler finds that the transmit queue has not moved
since the previous timeout, it drops the link back to slow start
and forces a probe containing the last sent sequence number to the
sent to the peer, so that this can discover the stale situation.
This change does in reality have effect only on unicast ethernet
transport, as we have seen that there is no room whatsoever for
increasing the window max size for the UDP bearer.
For now, we also choose to keep the limits for the broadcast link
unchanged and equal.
This algorithm seems to give a 50-100% throughput improvement for
messages larger than MTU.
Suggested-by: Xin Long <lucien.xin@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Mon, 9 Dec 2019 23:52:45 +0000 (00:52 +0100)]
tipc: eliminate more unnecessary nacks and retransmissions
When we increase the link tranmsit window we often observe the following
scenario:
1) A STATE message bypasses a sequence of traffic packets and arrives
far ahead of those to the receiver. STATE messages contain a
'peers_nxt_snt' field to indicate which was the last packet sent
from the peer. This mechanism is intended as a last resort for the
receiver to detect missing packets, e.g., during very low traffic
when there is no packet flow to help early loss detection.
3) The receiving link compares the 'peer_nxt_snt' field to its own
'rcv_nxt', finds that there is a gap, and immediately sends a
NACK message back to the peer.
4) When this NACKs arrives at the sender, all the requested
retransmissions are performed, since it is a first-time request.
Just like in the scenario described in the previous commit this leads
to many redundant retransmissions, with decreased throughput as a
consequence.
We fix this by adding two more conditions before we send a NACK in
this sitution. First, the deferred queue must be empty, so we cannot
assume that the potential packet loss has already been detected by
other means. Second, we check the 'peers_snd_nxt' field only in probe/
probe_reply messages, thus turning this into a true mechanism of last
resort as it was really meant to be.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy [Mon, 9 Dec 2019 23:52:44 +0000 (00:52 +0100)]
tipc: eliminate gap indicator from ACK messages
When we increase the link send window we sometimes observe the
following scenario:
1) A packet #N arrives out of order far ahead of a sequence of older
packets which are still under way. The packet is added to the
deferred queue.
2) The missing packets arrive in sequence, and for each 16th of them
an ACK is sent back to the receiver, as it should be.
3) When building those ACK messages, it is checked if there is a gap
between the link's 'rcv_nxt' and the first packet in the deferred
queue. This is always the case until packet number #N-1 arrives, and
a 'gap' indicator is added, effectively turning them into NACK
messages.
4) When those NACKs arrive at the sender, all the requested
retransmissions are done, since it is a first-time request.
This sometimes leads to a huge amount of redundant retransmissions,
causing a drop in max throughput. This problem gets worse when we
in a later commit introduce variable window congestion control,
since it drops the link back to 'fast recovery' much more often
than necessary.
We now fix this by not sending any 'gap' indicator in regular ACK
messages. We already have a mechanism for sending explicit NACKs
in place, and this is sufficient to keep up the packet flow.
Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
../drivers/net/ppp/ppp_async.c:877:6: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
ap->rpkt = skb;
^
../drivers/net/ppp/ppp_async.c:875:5: note: previous statement is here
if (!skb)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Clean up this entire block's indentation so that it is consistent
with the Linux kernel coding style and clang no longer warns.
Fixes: 6722e78c9005 ("[PPP]: handle misaligned accesses") Link: https://github.com/ClangBuiltLinux/linux/issues/800 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: smc911x: Adjust indentation in smc911x_phy_configure
Clang warns:
../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if (!lp->ctl_rfduplx)
^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
if (lp->ctl_rspeed != 100)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 0a0c72c9118c ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips") Link: https://github.com/ClangBuiltLinux/linux/issues/796 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: tulip: Adjust indentation in {dmfe, uli526x}_init_module
Clang warns:
../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch (mode) {
^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
switch(mode) {
^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
if (cr6set)
^
1 warning generated.
This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.
Fixes: e1c3e5014040 ("[PATCH] initialisation cleanup for ULI526x-net-driver") Link: https://github.com/ClangBuiltLinux/linux/issues/795 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 Dec 2019 04:19:10 +0000 (20:19 -0800)]
Merge branch 'dp83867-fix-fifo-depth'
Dan Murphy says:
====================
Fix Tx/Rx FIFO depth for DP83867
The DP83867 supports both the RGMII and SGMII modes. The Tx and Rx FIFO depths
are configurable in these modes but may not applicable for both modes.
When the device is configured for RGMII mode the Tx FIFO depth is applicable
and for SGMII mode both Tx and Rx FIFO depth settings are applicable. When
the driver was originally written only the RGMII device was available and there
were no standard fifo-depth DT properties.
The patchset converts the special ti,fifo-depth property to the standard
tx-fifo-depth property while still allowing the ti,fifo-depth property to be
set as to maintain backward compatibility.
In addition to this change the rx-fifo-depth property support was added and only
written when the device is configured for SGMII mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Mon, 9 Dec 2019 20:10:25 +0000 (14:10 -0600)]
net: phy: dp83867: Add rx-fifo-depth and tx-fifo-depth
This code changes the TI specific ti,fifo-depth to the common
tx-fifo-depth property. The tx depth is applicable for both RGMII and
SGMII modes of operation.
rx-fifo-depth was added as well but this is only applicable for SGMII
mode.
So in summary
if RGMII mode write tx fifo depth only
if SGMII mode write both rx and tx fifo depths
If the property is not populated in the device tree then set the value
to the default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy [Mon, 9 Dec 2019 20:10:24 +0000 (14:10 -0600)]
dt-bindings: dp83867: Convert fifo-depth to common fifo-depth and make optional
Convert the ti,fifo-depth from a TI specific property to the common
tx-fifo-depth property. Also add support for the rx-fifo-depth.
These are optional properties for this device and if these are not
available then the fifo depths are set to device default values.
Signed-off-by: Dan Murphy <dmurphy@ti.com> Reported-by: Adrian Bunk <bunk@kernel.org> CC: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net-tcp: Disable TCP ssthresh metrics cache by default
This patch introduces a sysctl knob "net.ipv4.tcp_no_ssthresh_metrics_save"
that disables TCP ssthresh metrics cache by default. Other parts of TCP
metrics cache, e.g. rtt, cwnd, remain unchanged.
As modern networks becoming more and more dynamic, TCP metrics cache
today often causes more harm than benefits. For example, the same IP
address is often shared by different subscribers behind NAT in residential
networks. Even if the IP address is not shared by different users,
caching the slow-start threshold of a previous short flow using loss-based
congestion control (e.g. cubic) often causes the future longer flows of
the same network path to exit slow-start prematurely with abysmal
throughput.
Caching ssthresh is very risky and can lead to terrible performance.
Therefore it makes sense to make disabling ssthresh caching by
default and opt-in for specific networks by the administrators.
This practice also has worked well for several years of deployment with
CUBIC congestion control at Google.
Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Kevin(Yudong) Yang <yyd@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 9 Dec 2019 05:45:18 +0000 (13:45 +0800)]
sctp: get netns from asoc and ep base
Commit 312434617cb1 ("sctp: cache netns in sctp_ep_common") set netns
in asoc and ep base since they're created, and it will never change.
It's a better way to get netns from asoc and ep base, comparing to
calling sock_net().
This patch is to replace them.
v1->v2:
- no change.
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 9 Dec 2019 13:40:23 +0000 (13:40 +0000)]
net: sfp: avoid tx-fault with Nokia GPON module
The Nokia GPON module can hold tx-fault active while it is initialising
which can take up to 60s. Avoid this causing the module to be declared
faulty after the SFP MSA defined non-cooled module timeout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 9 Dec 2019 13:16:07 +0000 (13:16 +0000)]
qed: remove redundant assignments to rc
The variable rc is assigned with a value that is never read and
it is re-assigned a new value later on. The assignment is redundant
and can be removed. Clean up multiple occurrances of this pattern.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the first bluetooth-next pull request for 5.6:
- Devicetree bindings updates for Broadcom controllers
- Add support for PCM configuration for Broadcom controllers
- btusb: Fixes for Realtek devices
- butsb: A few other smaller fixes (mem leak & non-atomic allocation issue)
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WireGuard is a layer 3 secure networking tunnel made specifically for
the kernel, that aims to be much simpler and easier to audit than IPsec.
Extensive documentation and description of the protocol and
considerations, along with formal proofs of the cryptography, are
available at:
This commit implements WireGuard as a simple network device driver,
accessible in the usual RTNL way used by virtual network drivers. It
makes use of the udp_tunnel APIs, GRO, GSO, NAPI, and the usual set of
networking subsystem APIs. It has a somewhat novel multicore queueing
system designed for maximum throughput and minimal latency of encryption
operations, but it is implemented modestly using workqueues and NAPI.
Configuration is done via generic Netlink, and following a review from
the Netlink maintainer a year ago, several high profile userspace tools
have already implemented the API.
This commit also comes with several different tests, both in-kernel
tests and out-of-kernel tests based on network namespaces, taking profit
of the fact that sockets used by WireGuard intentionally stay in the
namespace the WireGuard interface was originally created, exactly like
the semantics of userspace tun devices. See wireguard.com/netns/ for
pictures and examples.
The source code is fairly short, but rather than combining everything
into a single file, WireGuard is developed as cleanly separable files,
making auditing and comprehension easier. Things are laid out as
follows:
* noise.[ch], cookie.[ch], messages.h: These implement the bulk of the
cryptographic aspects of the protocol, and are mostly data-only in
nature, taking in buffers of bytes and spitting out buffers of
bytes. They also handle reference counting for their various shared
pieces of data, like keys and key lists.
* ratelimiter.[ch]: Used as an integral part of cookie.[ch] for
ratelimiting certain types of cryptographic operations in accordance
with particular WireGuard semantics.
* allowedips.[ch], peerlookup.[ch]: The main lookup structures of
WireGuard, the former being trie-like with particular semantics, an
integral part of the design of the protocol, and the latter just
being nice helper functions around the various hashtables we use.
* device.[ch]: Implementation of functions for the netdevice and for
rtnl, responsible for maintaining the life of a given interface and
wiring it up to the rest of WireGuard.
* peer.[ch]: Each interface has a list of peers, with helper functions
available here for creation, destruction, and reference counting.
* socket.[ch]: Implementation of functions related to udp_socket and
the general set of kernel socket APIs, for sending and receiving
ciphertext UDP packets, and taking care of WireGuard-specific sticky
socket routing semantics for the automatic roaming.
* netlink.[ch]: Userspace API entry point for configuring WireGuard
peers and devices. The API has been implemented by several userspace
tools and network management utility, and the WireGuard project
distributes the basic wg(8) tool.
* queueing.[ch]: Shared function on the rx and tx path for handling
the various queues used in the multicore algorithms.
* send.c: Handles encrypting outgoing packets in parallel on
multiple cores, before sending them in order on a single core, via
workqueues and ring buffers. Also handles sending handshake and cookie
messages as part of the protocol, in parallel.
* receive.c: Handles decrypting incoming packets in parallel on
multiple cores, before passing them off in order to be ingested via
the rest of the networking subsystem with GRO via the typical NAPI
poll function. Also handles receiving handshake and cookie messages
as part of the protocol, in parallel.
* timers.[ch]: Uses the timer wheel to implement protocol particular
event timeouts, and gives a set of very simple event-driven entry
point functions for callers.
* main.c, version.h: Initialization and deinitialization of the module.
* selftest/*.h: Runtime unit tests for some of the most security
sensitive functions.
* tools/testing/selftests/wireguard/netns.sh: Aforementioned testing
script using network namespaces.
This commit aims to be as self-contained as possible, implementing
WireGuard as a standalone module not needing much special handling or
coordination from the network subsystem. I expect for future
optimizations to the network stack to positively improve WireGuard, and
vice-versa, but for the time being, this exists as intentionally
standalone.
We introduce a menu option for CONFIG_WIREGUARD, as well as providing a
verbose debug log and self-tests via CONFIG_WIREGUARD_DEBUG.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: David Miller <davem@davemloft.net> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
1) More jumbo frame fixes in r8169, from Heiner Kallweit.
2) Fix bpf build in minimal configuration, from Alexei Starovoitov.
3) Use after free in slcan driver, from Jouni Hogander.
4) Flower classifier port ranges don't work properly in the HW offload
case, from Yoshiki Komachi.
5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.
6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.
7) Fix flow dissection in dsa TX path, from Alexander Lobakin.
8) Stale syncookie timestampe fixes from Guillaume Nault.
[ Did an evil merge to silence a warning introduced by this pull - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
r8169: add missing RX enabling for WoL on RTL8125
vhost/vsock: accept only packets with the right dst_cid
net: phy: dp83867: fix hfs boot in rgmii mode
net: ethernet: ti: cpsw: fix extra rx interrupt
inet: protect against too small mtu values.
gre: refetch erspan header from skb->data after pskb_may_pull()
pppoe: remove redundant BUG_ON() check in pppoe_pernet
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
tcp: tighten acceptance of ACKs not matching a child socket
tcp: fix rejected syncookies due to stale timestamps
lpc_eth: kernel BUG on remove
tcp: md5: fix potential overestimation of TCP option space
net: sched: allow indirect blocks to bind to clsact in TC
net: core: rename indirect block ingress cb function
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
net: dsa: fix flow dissection on Tx path
net/tls: Fix return values to avoid ENOTSUPP
net: avoid an indirect call in ____sys_recvmsg()
...
Linus Torvalds [Sun, 8 Dec 2019 20:23:42 +0000 (12:23 -0800)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Eleven patches, all in drivers (no core changes) that are either minor
cleanups or small fixes.
They were late arriving, but still safe for -rc1"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
scsi: megaraid_sas: Make poll_aen_lock static
scsi: sd_zbc: Improve report zones error printout
scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
scsi: qla2xxx: unregister ports after GPN_FT failure
scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
scsi: pm80xx: Remove unused include of linux/version.h
scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
scsi: scsi_transport_sas: Fix memory leak when removing devices
scsi: lpfc: size cpu map by last cpu id set
scsi: ibmvscsi_tgt: Remove unneeded variable rc
Linus Torvalds [Sun, 8 Dec 2019 20:12:18 +0000 (12:12 -0800)]
Merge tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Nine cifs/smb3 fixes:
- one fix for stable (oops during oplock break)
- two timestamp fixes including important one for updating mtime at
close to avoid stale metadata caching issue on dirty files (also
improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
wire)
- two fixes for "modefromsid" mount option for file create (now
allows mode bits to be set more atomically and accurately on create
by adding "sd_context" on create when modefromsid specified on
mount)
- two fixes for multichannel found in testing this week against
different servers
- two small cleanup patches"
* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: improve check for when we send the security descriptor context on create
smb3: fix mode passed in on create for modetosid mount option
cifs: fix possible uninitialized access and race on iface_list
cifs: Fix lookup of SMB connections on multichannel
smb3: query attributes on file close
smb3: remove unused flag passed into close functions
cifs: remove redundant assignment to pointer pneg_ctxt
fs: cifs: Fix atime update check vs mtime
CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks
Linus Torvalds [Sun, 8 Dec 2019 19:08:28 +0000 (11:08 -0800)]
Merge branch 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"No common topic, just three cleanups".
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
make __d_alloc() static
fs/namespace: add __user to open_tree and move_mount syscalls
fs/fnctl: fix missing __user in fcntl_rw_hint()
Linus Torvalds [Sun, 8 Dec 2019 01:07:18 +0000 (17:07 -0800)]
Merge tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap fixes from Darrick Wong:
"Fix a race condition and a use-after-free error:
- Fix a UAF when reporting writeback errors
- Fix a race condition when handling page uptodate on fragmented file
with blocksize < pagesize"
* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: stop using ioend after it's been freed in iomap_finish_ioend()
iomap: fix sub-page uptodate handling
Linus Torvalds [Sun, 8 Dec 2019 01:05:33 +0000 (17:05 -0800)]
Merge tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Fix a couple of resource management errors and a hang:
- fix a crash in the log setup code when log mounting fails
- fix a hang when allocating space on the realtime device
- fix a block leak when freeing space on the realtime device"
* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix mount failure crash on invalid iclog memory access
xfs: don't check for AG deadlock for realtime files in bunmapi
xfs: fix realtime file data space leak
Linus Torvalds [Sun, 8 Dec 2019 00:59:25 +0000 (16:59 -0800)]
Merge tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs update from Mike Marshall:
"orangefs: posix open permission checking...
Orangefs has no open, and orangefs checks file permissions on each
file access. Posix requires that file permissions be checked on open
and nowhere else. Orangefs-through-the-kernel needs to seem posix
compliant.
The VFS opens files, even if the filesystem provides no method. We can
see if a file was successfully opened for read and or for write by
looking at file->f_mode.
When writes are flowing from the page cache, file is no longer
available. We can trust the VFS to have checked file->f_mode before
writing to the page cache.
The mode of a file might change between when it is opened and IO
commences, or it might be created with an arbitrary mode.
We'll make sure we don't hit EACCES during the IO stage by using
UID 0"
[ This is "posixish", but not a great solution in the long run, since a
proper secure network server shouldn't really trust the client like this.
But proper and secure POSIX behavior requires an open method and a
resulting cookie for IO of some kind, or similar. - Linus ]
* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: posix open permission checking...
Linus Torvalds [Sun, 8 Dec 2019 00:56:00 +0000 (16:56 -0800)]
Merge tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"This is a relatively quiet cycle for nfsd, mainly various bugfixes.
Possibly most interesting is Trond's fixes for some callback races
that were due to my incomplete understanding of rpc client shutdown.
Unfortunately at the last minute I've started noticing a new
intermittent failure to send callbacks. As the logic seems basically
correct, I'm leaving Trond's patches in for now, and hope to find a
fix in the next week so I don't have to revert those patches"
* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
nfsd: depend on CRYPTO_MD5 for legacy client tracking
NFSD fixing possible null pointer derefering in copy offload
nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
nfsd: Ensure CLONE persists data and metadata changes to the target file
SUNRPC: Fix backchannel latency metrics
nfsd: restore NFSv3 ACL support
nfsd: v4 support requires CRYPTO_SHA256
nfsd: Fix cld_net->cn_tfm initialization
lockd: remove __KERNEL__ ifdefs
sunrpc: remove __KERNEL__ ifdefs
race in exportfs_decode_fh()
nfsd: Drop LIST_HEAD where the variable it declares is never used.
nfsd: document callback_wq serialization of callback code
nfsd: mark cb path down on unknown errors
nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
nfsd: minor 4.1 callback cleanup
SUNRPC: Fix svcauth_gss_proxy_init()
SUNRPC: Trace gssproxy upcall results
sunrpc: fix crash when cache_head become valid before update
nfsd: remove private bin2hex implementation
...
Linus Torvalds [Sun, 8 Dec 2019 00:50:55 +0000 (16:50 -0800)]
Merge tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- NFSv4.2 now supports cross device offloaded copy (i.e. offloaded
copy of a file from one source server to a different target
server).
- New RDMA tracepoints for debugging congestion control and Local
Invalidate WRs.
Bugfixes and cleanups
- Drop the NFSv4.1 session slot if nfs4_delegreturn_prepare waits for
layoutreturn
- Handle bad/dead sessions correctly in nfs41_sequence_process()
- Various bugfixes to the delegation return operation.
- Various bugfixes pertaining to delegations that have been revoked.
- Cleanups to the NFS timespec code to avoid unnecessary conversions
between timespec and timespec64.
- Fix unstable RDMA connections after a reconnect
- Close race between waking an RDMA sender and posting a receive
- Wake pending RDMA tasks if connection fails
- Fix MR list corruption, and clean up MR usage
- Fix another RPCSEC_GSS issue with MIC buffer space"
* tag 'nfs-for-5.5-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
SUNRPC: Capture completion of all RPC tasks
SUNRPC: Fix another issue with MIC buffer space
NFS4: Trace lock reclaims
NFS4: Trace state recovery operation
NFSv4.2 fix memory leak in nfs42_ssc_open
NFSv4.2 fix kfree in __nfs42_copy_file_range
NFS: remove duplicated include from nfs4file.c
NFSv4: Make _nfs42_proc_copy_notify() static
NFS: Fallocate should use the nfs4_fattr_bitmap
NFS: Return -ETXTBSY when attempting to write to a swapfile
fs: nfs: sysfs: Remove NULL check before kfree
NFS: remove unneeded semicolon
NFSv4: add declaration of current_stateid
NFSv4.x: Drop the slot if nfs4_delegreturn_prepare waits for layoutreturn
NFSv4.x: Handle bad/dead sessions correctly in nfs41_sequence_process()
nfsv4: Move NFSPROC4_CLNT_COPY_NOTIFY to end of list
SUNRPC: Avoid RPC delays when exiting suspend
NFS: Add a tracepoint in nfs_fh_to_dentry()
NFSv4: Don't retry the GETATTR on old stateid in nfs4_delegreturn_done()
NFSv4: Handle NFS4ERR_OLD_STATEID in delegreturn
...
Steve French [Sat, 7 Dec 2019 23:38:22 +0000 (17:38 -0600)]
smb3: improve check for when we send the security descriptor context on create
We had cases in the previous patch where we were sending the security
descriptor context on SMB3 open (file create) in cases when we hadn't
mounted with with "modefromsid" mount option.
Add check for that mount flag before calling ad_sd_context in
open init.
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Linus Torvalds [Sat, 7 Dec 2019 22:51:04 +0000 (14:51 -0800)]
Merge tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Remove hugepage checks for reserved pfns (Ben Luo)
- Fix irq-bypass unregister ordering (Jiang Yi)
* tag 'vfio-v5.5-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: call irq_bypass_unregister_producer() before freeing irq
vfio/type1: remove hugepage checks in is_invalid_reserved_pfn()
Linus Torvalds [Sat, 7 Dec 2019 22:49:20 +0000 (14:49 -0800)]
Merge tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- a patch to fix a build warning
- a cleanup of no longer needed code in the Xen event handling
- a small series for the Xen grant driver avoiding high order
allocations and replacing an insane global limit by a per-call one
- a small series fixing Xen frontend/backend module referencing
* tag 'for-linus-5.5b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-blkback: allow module to be cleanly unloaded
xen/xenbus: reference count registered modules
xen/gntdev: switch from kcalloc() to kvcalloc()
xen/gntdev: replace global limit of mapped pages by limit per call
xen/gntdev: remove redundant non-zero check on ret
xen/events: remove event handling recursion detection
Linus Torvalds [Sat, 7 Dec 2019 22:43:46 +0000 (14:43 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc Kconfig updates from Andrew Morton:
"A number of changes to Kconfig files under lib/ from Changbin Du and
Krzysztof Kozlowski"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/: fix Kconfig indentation
kernel-hacking: move DEBUG_FS to 'Generic Kernel Debugging Instruments'
kernel-hacking: move DEBUG_BUGVERBOSE to 'printk and dmesg options'
kernel-hacking: create a submenu for scheduler debugging options
kernel-hacking: move SCHED_STACK_END_CHECK after DEBUG_STACK_USAGE
kernel-hacking: move Oops into 'Lockups and Hangs'
kernel-hacking: move kernel testing and coverage options to same submenu
kernel-hacking: group kernel data structures debugging together
kernel-hacking: create submenu for arch special debugging options
kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'
Heiner Kallweit [Sat, 7 Dec 2019 21:21:52 +0000 (22:21 +0100)]
r8169: fix rtl_hw_jumbo_disable for RTL8168evl
In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().
v2: fix referenced commit id
Fixes: 14012c9f3bb9 ("r8169: fix jumbo configuration for RTL8168evl") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 7 Dec 2019 21:53:09 +0000 (13:53 -0800)]
pipe: don't use 'pipe_wait() for basic pipe IO
pipe_wait() may be simple, but since it relies on the pipe lock, it
means that we have to do the wakeup while holding the lock. That's
unfortunate, because the very first thing the waked entity will want to
do is to get the pipe lock for itself.
So get rid of the pipe_wait() usage by simply releasing the pipe lock,
doing the wakeup (if required) and then using wait_event_interruptible()
to wait on the right condition instead.
wait_event_interruptible() handles races on its own by comparing the
wakeup condition before and after adding itself to the wait queue, so
you can use an optimistic unlocked condition for it.
Cc: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Dec 2019 21:21:01 +0000 (13:21 -0800)]
pipe: remove 'waiting_writers' merging logic
This code is ancient, and goes back to when we only had a single page
for the pipe buffers. The exact history is hidden in the mists of time
(ie "before git", and in fact predates the BK repository too).
At that long-ago point in time, it actually helped to try to merge big
back-and-forth pipe reads and writes, and not limit pipe reads to the
single pipe buffer in length just because that was all we had at a time.
However, since then we've expanded the pipe buffers to multiple pages,
and this logic really doesn't seem to make sense. And a lot of it is
somewhat questionable (ie "hmm, the user asked for a non-blocking read,
but we see that there's a writer pending, so let's wait anyway to get
the extra data that the writer will have").
But more importantly, it makes the "go to sleep" logic much less
obvious, and considering the wakeup issues we've had, I want to make for
less of those kinds of things.
Cc: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Dec 2019 20:54:26 +0000 (12:54 -0800)]
pipe: fix and clarify pipe read wakeup logic
This is the read side version of the previous commit: it simplifies the
logic to only wake up waiting writers when necessary, and makes sure to
use a synchronous wakeup. This time not so much for GNU make jobserver
reasons (that pipe never fills up), but simply to get the writer going
quickly again.
A bit less verbose commentary this time, if only because I assume that
the write side commentary isn't going to be ignored if you touch this
code.
Cc: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Dec 2019 20:14:28 +0000 (12:14 -0800)]
pipe: fix and clarify pipe write wakeup logic
The pipe rework ends up having been extra painful, partly becaused of
actual bugs with ordering and caching of the pipe state, but also
because of subtle performance issues.
In particular, the pipe rework caused the kernel build to inexplicably
slow down.
The reason turns out to be that the GNU make jobserver (which limits the
parallelism of the build) uses a pipe to implement a "token" system: a
parallel submake will read a character from the pipe to get the job
token before starting a new job, and will write a character back to the
pipe when it is done. The overall job limit is thus easily controlled
by just writing the appropriate number of initial token characters into
the pipe.
But to work well, that really means that the old behavior of write
wakeups being synchronous (WF_SYNC) is very important - when the pipe
writer wakes up a reader, we want the reader to actually get scheduled
immediately. Otherwise you lose the parallelism of the build.
The pipe rework lost that synchronous wakeup on write, and we had
clearly all forgotten the reasons and rules for it.
This rewrites the pipe write wakeup logic to do the required Wsync
wakeups, but also clarifies the logic and avoids extraneous wakeups.
It also ends up addign a number of comments about what oit does and why,
so that we hopefully don't end up forgetting about this next time we
change this code.
Cc: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiner Kallweit [Fri, 6 Dec 2019 22:27:15 +0000 (23:27 +0100)]
r8169: add missing RX enabling for WoL on RTL8125
RTL8125 also requires to enable RX for WoL.
v2: add missing Fixes tag
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe")
causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is
used in "rgmii-id" mode - the networking stops working.
Unfortunately, it's not enough to just move DT parsing code to .probe() as
it depends on phydev->interface value, which is set to correct value abter
the .probe() is completed and before calling .config_init(). So, RGMII
configuration can't be loaded from DT.
To fix and issue
- move RGMII validation code to .config_init()
- parse RGMII parameters in dp83867_of_init(), but consider them as
optional.
Fixes: ef87f7da6b28 ("net: phy: dp83867: move dt parsing to probe") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feabdc ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 6 Dec 2019 04:43:46 +0000 (20:43 -0800)]
inet: protect against too small mtu values.
syzbot was once again able to crash a host by setting a very small mtu
on loopback device.
Let's make inetdev_valid_mtu() available in include/net/ip.h,
and use it in ip_setup_cork(), so that we protect both ip_append_page()
and __ip_append_data()
Also add a READ_ONCE() when the device mtu is read.
Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(),
even if other code paths might write over this field.
Add a big comment in include/linux/netdevice.h about dev->mtu
needing READ_ONCE()/WRITE_ONCE() annotations.
Hopefully we will add the missing ones in followup patches.
Fixes: 1470ddf7f8ce ("inet: Remove explicit write references to sk/inet in ip_append_data") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Fri, 6 Dec 2019 03:39:02 +0000 (19:39 -0800)]
gre: refetch erspan header from skb->data after pskb_may_pull()
After pskb_may_pull() we should always refetch the header
pointers from the skb->data in case it got reallocated.
In gre_parse_header(), the erspan header is still fetched
from the 'options' pointer which is fetched before
pskb_may_pull().
Found this during code review of a KMSAN bug report.
Fixes: cb73ee40b1b3 ("net: ip_gre: use erspan key field for tunnel lookup") Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: William Tu <u9012063@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aditya Pakki [Thu, 5 Dec 2019 23:04:49 +0000 (17:04 -0600)]
pppoe: remove redundant BUG_ON() check in pppoe_pernet
Passing NULL to pppoe_pernet causes a crash via BUG_ON.
Dereferencing net in net_generici() also has the same effect. This patch
removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Changbin Du [Sat, 7 Dec 2019 01:03:42 +0000 (17:03 -0800)]
kernel-hacking: group sysrq/kgdb/ubsan into 'Generic Kernel Debugging Instruments'
Patch series "hacking: make 'kernel hacking' menu better structurized", v3.
This series is a trivial improvment for the layout of 'kernel hacking'
configuration menu. Now we have many items in it which makes takes a
little time to look up them since they are not well structurized yet.
Early discussion is here:
https://lkml.org/lkml/2019/9/1/39
This patch (of 9):
Group generic kernel debugging instruments sysrq/kgdb/ubsan together
into a new submenu.
Link: http://lkml.kernel.org/r/20190909144453.3520-2-changbin.du@gmail.com Signed-off-by: Changbin Du <changbin.du@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 7 Dec 2019 18:41:17 +0000 (10:41 -0800)]
pipe: fix poll/select race introduced by the pipe rework
The kernel wait queues have a basic rule to them: you add yourself to
the wait-queue first, and then you check the things that you're going to
wait on. That avoids the races with the event you're waiting for.
The same goes for poll/select logic: the "poll_wait()" goes first, and
then you check the things you're polling for.
Of course, if you use locking, the ordering doesn't matter since the
lock will serialize with anything that changes the state you're looking
at. That's not the case here, though.
So move the poll_wait() first in pipe_poll(), before you start looking
at the pipe state.
Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length") Cc: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nfsd: depend on CRYPTO_MD5 for legacy client tracking
The legacy client tracking infrastructure of nfsd makes use of MD5 to
derive a client's recovery directory name. As the nfsd module doesn't
declare any dependency on CRYPTO_MD5, though, it may fail to allocate
the hash if the kernel was compiled without it. As a result, generation
of client recovery directories will fail with the following error:
NFSD: unable to generate recoverydir name
The explicit dependency on CRYPTO_MD5 was removed as redundant back in 6aaa67b5f3b9 (NFSD: Remove redundant "select" clauses in fs/Kconfig
2008-02-11) as it was already implicitly selected via RPCSEC_GSS_KRB5.
This broke when RPCSEC_GSS_KRB5 was made optional for NFSv4 in commit df486a25900f (NFS: Fix the selection of security flavours in Kconfig) at
a later point.
Fix the issue by adding back an explicit dependency on CRYPTO_MD5.
Fixes: df486a25900f (NFS: Fix the selection of security flavours in Kconfig) Signed-off-by: Patrick Steinhardt <ps@pks.im> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
NFSD fixing possible null pointer derefering in copy offload
Static checker revealed possible error path leading to possible
NULL pointer dereferencing.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: e0639dc5805a: ("NFSD introduce async copy feature") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
====================
tcp: fix handling of stale syncookies timestamps
The synflood timestamps (->ts_recent_stamp and ->synq_overflow_ts) are
only refreshed when the syncookie protection triggers. Therefore, their
value can become very far apart from jiffies if no synflood happens for
a long time.
If jiffies grows too much and wraps while the synflood timestamp isn't
refreshed, then time_after32() might consider the later to be in the
future. This can trick tcp_synq_no_recent_overflow() into returning
erroneous values and rejecting valid ACKs.
Patch 1 handles the case of ACKs using legitimate syncookies.
Patch 2 handles the case of stray ACKs.
Patch 3 annotates lockless timestamp operations with READ_ONCE() and
WRITE_ONCE().
Changes from v3:
- Fix description of time_between32() (found by Eric Dumazet).
- Use more accurate Fixes tag in patch 3 (suggested by Eric Dumazet).
Changes from v2:
- Define and use time_between32() instead of a pair of
time_before32/time_after32 (suggested by Eric Dumazet).
- Use 'last_overflow - HZ' as lower bound in
tcp_synq_no_recent_overflow(), to accommodate for concurrent
timestamp updates (found by Eric Dumazet).
- Add a third patch to annotate lockless accesses to .ts_recent_stamp.
Changes from v1:
- Initialising timestamps at socket creation time is not enough
because jiffies wraps in 24 days with HZ=1000 (Eric Dumazet).
Handle stale timestamps in tcp_synq_overflow() and
tcp_synq_no_recent_overflow() instead.
- Rework commit description.
- Add a second patch to handle the case of stray ACKs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:49 +0000 (12:38 +0100)]
tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the
timestamp of the last synflood. Protect them with READ_ONCE() and
WRITE_ONCE() since reads and writes aren't serialised.
Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was
introduced by a0f82f64e269 ("syncookies: remove last_synq_overflow from
struct tcp_sock"). But unprotected accesses were already there when
timestamp was stored in .last_synq_overflow.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:43 +0000 (12:38 +0100)]
tcp: tighten acceptance of ACKs not matching a child socket
When no synflood occurs, the synflood timestamp isn't updated.
Therefore it can be so old that time_after32() can consider it to be
in the future.
That's a problem for tcp_synq_no_recent_overflow() as it may report
that a recent overflow occurred while, in fact, it's just that jiffies
has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31.
Spurious detection of recent overflows lead to extra syncookie
verification in cookie_v[46]_check(). At that point, the verification
should fail and the packet dropped. But we should have dropped the
packet earlier as we didn't even send a syncookie.
Let's refine tcp_synq_no_recent_overflow() to report a recent overflow
only if jiffies is within the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This
way, no spurious recent overflow is reported when jiffies wraps and
'last_overflow' becomes in the future from the point of view of
time_after32().
However, if jiffies wraps and enters the
[last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with
'last_overflow' being a stale synflood timestamp), then
tcp_synq_no_recent_overflow() still erroneously reports an
overflow. In such cases, we have to rely on syncookie verification
to drop the packet. We unfortunately have no way to differentiate
between a fresh and a stale syncookie timestamp.
In practice, using last_overflow as lower bound is problematic.
If the synflood timestamp is concurrently updated between the time
we read jiffies and the moment we store the timestamp in
'last_overflow', then 'now' becomes smaller than 'last_overflow' and
tcp_synq_no_recent_overflow() returns true, potentially dropping a
valid syncookie.
Reading jiffies after loading the timestamp could fix the problem,
but that'd require a memory barrier. Let's just accommodate for
potential timestamp growth instead and extend the interval using
'last_overflow - HZ' as lower bound.
Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 6 Dec 2019 11:38:36 +0000 (12:38 +0100)]
tcp: fix rejected syncookies due to stale timestamps
If no synflood happens for a long enough period of time, then the
synflood timestamp isn't refreshed and jiffies can advance so much
that time_after32() can't accurately compare them any more.
Therefore, we can end up in a situation where time_after32(now,
last_overflow + HZ) returns false, just because these two values are
too far apart. In that case, the synflood timestamp isn't updated as
it should be, which can trick tcp_synq_no_recent_overflow() into
rejecting valid syncookies.
For example, let's consider the following scenario on a system
with HZ=1000:
* The synflood timestamp is 0, either because that's the timestamp
of the last synflood or, more commonly, because we're working with
a freshly created socket.
* We receive a new SYN, which triggers synflood protection. Let's say
that this happens when jiffies == 2147484649 (that is,
'synflood timestamp' + HZ + 2^31 + 1).
* Then tcp_synq_overflow() doesn't update the synflood timestamp,
because time_after32(2147484649, 1000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 1000: the value of 'last_overflow' + HZ.
* A bit later, we receive the ACK completing the 3WHS. But
cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow()
says that we're not under synflood. That's because
time_after32(2147484649, 120000) returns false.
With:
- 2147484649: the value of jiffies, aka. 'now'.
- 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID.
Of course, in reality jiffies would have increased a bit, but this
condition will last for the next 119 seconds, which is far enough
to accommodate for jiffie's growth.
Fix this by updating the overflow timestamp whenever jiffies isn't
within the [last_overflow, last_overflow + HZ] range. That shouldn't
have any performance impact since the update still happens at most once
per second.
Now we're guaranteed to have fresh timestamps while under synflood, so
tcp_synq_no_recent_overflow() can safely use it with time_after32() in
such situations.
Stale timestamps can still make tcp_synq_no_recent_overflow() return
the wrong verdict when not under synflood. This will be handled in the
next patch.
For 64 bits architectures, the problem was introduced with the
conversion of ->tw_ts_recent_stamp to 32 bits integer by commit cca9bab1b72c ("tcp: use monotonic timestamps for PAWS").
The problem has always been there on 32 bits architectures.
Fixes: cca9bab1b72c ("tcp: use monotonic timestamps for PAWS") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull and let me know if there is any problem.
For -stable v4.19:
('net/mlx5e: Query global pause state before setting prio2buffer')
For -stable v5.3
('net/mlx5e: Fix SFF 8472 eeprom length')
('net/mlx5e: Fix translation of link mode into speed')
('net/mlx5e: Fix freeing flow with kfree() and not kvfree()')
('net/mlx5e: ethtool, Fix analysis of speed setting')
('net/mlx5e: Fix TXQ indices to be sequential')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: Daniel Martinez <linux@danielsmartinez.com> Signed-off-by: Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Dec 2019 04:45:09 +0000 (20:45 -0800)]
Merge branch 'net-tc-indirect-block-relay'
John Hurley says:
====================
Ensure egress un/bind are relayed with indirect blocks
On register and unregister for indirect blocks, a command is called that
sends a bind/unbind event to the registering driver. This command assumes
that the bind to indirect block will be on ingress. However, drivers such
as NFP have allowed binding to clsact qdiscs as well as ingress qdiscs
from mainline Linux 5.2. A clsact qdisc binds to an ingress and an egress
block.
Rather than assuming that an indirect bind is always ingress, modify the
function names to remove the ingress tag (patch 1). In cls_api, which is
used by NFP to offload TC flower, generate bind/unbind message for both
ingress and egress blocks on the event of indirectly
registering/unregistering from that block. Doing so mimics the behaviour
of both ingress and clsact qdiscs on initialise and destroy.
This now ensures that drivers such as NFP receive the correct binder type
for the indirect block registration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 5 Dec 2019 17:03:35 +0000 (17:03 +0000)]
net: sched: allow indirect blocks to bind to clsact in TC
When a device is bound to a clsact qdisc, bind events are triggered to
registered drivers for both ingress and egress. However, if a driver
registers to such a device using the indirect block routines then it is
assumed that it is only interested in ingress offload and so only replays
ingress bind/unbind messages.
The NFP driver supports the offload of some egress filters when
registering to a block with qdisc of type clsact. However, on unregister,
if the block is still active, it will not receive an unbind egress
notification which can prevent proper cleanup of other registered
callbacks.
Modify the indirect block callback command in TC to send messages of
ingress and/or egress bind depending on the qdisc in use. NFP currently
supports egress offload for TC flower offload so the changes are only
added to TC.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports") Signed-off-by: John Hurley <john.hurley@netronome.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 5 Dec 2019 17:03:34 +0000 (17:03 +0000)]
net: core: rename indirect block ingress cb function
With indirect blocks, a driver can register for callbacks from a device
that is does not 'own', for example, a tunnel device. When registering to
or unregistering from a new device, a callback is triggered to generate
a bind/unbind event. This, in turn, allows the driver to receive any
existing rules or to properly clean up installed rules.
When first added, it was assumed that all indirect block registrations
would be for ingress offloads. However, the NFP driver can, in some
instances, support clsact qdisc binds for egress offload.
Change the name of the indirect block callback command in flow_offload to
remove the 'ingress' identifier from it. While this does not change
functionality, a follow up patch will implement a more more generic
callback than just those currently just supporting ingress offload.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports") Signed-off-by: John Hurley <john.hurley@netronome.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jouni Hogander [Thu, 5 Dec 2019 13:57:07 +0000 (15:57 +0200)]
net-sysfs: Call dev_hold always in netdev_queue_add_kobject
Dev_hold has to be called always in netdev_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject") Reported-by: Hulk Robot <hulkci@huawei.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: David Miller <davem@davemloft.net> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 43e665287f93 ("net-next: dsa: fix flow dissection") added an
ability to override protocol and network offset during flow dissection
for DSA-enabled devices (i.e. controllers shipped as switch CPU ports)
in order to fix skb hashing for RPS on Rx path.
However, skb_hash() and added part of code can be invoked not only on
Rx, but also on Tx path if we have a multi-queued device and:
- kernel is running on UP system or
- XPS is not configured.
The call stack in this two cases will be like: dev_queue_xmit() ->
__dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() ->
skb_tx_hash() -> skb_get_hash().
The problem is that skbs queued for Tx have both network offset and
correct protocol already set up even after inserting a CPU tag by DSA
tagger, so calling tag_ops->flow_dissect() on this path actually only
breaks flow dissection and hashing.
This can be observed by adding debug prints just before and right after
tag_ops->flow_dissect() call to the related block of code:
In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)'
to prevent code from calling tag_ops->flow_dissect() on Tx.
I also decided to initialize 'offset' variable so tagger callbacks can
now safely leave it untouched without provoking a chaos.
Fixes: 43e665287f93 ("net-next: dsa: fix flow dissection") Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Valentin Vidic [Thu, 5 Dec 2019 06:41:18 +0000 (07:41 +0100)]
net/tls: Fix return values to avoid ENOTSUPP
ENOTSUPP is not available in userspace, for example:
setsockopt failed, 524, Unknown error 524
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 7 Dec 2019 00:12:39 +0000 (16:12 -0800)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- fix CPU topology setup for SCHED_MC case
- fix VDSO regression
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8947/1: Fix __arch_get_hw_counter() access to CNTVCT
ARM: 8943/1: Fix topology setup in case of CPU hotplug for CONFIG_SCHED_MC
Linus Torvalds [Fri, 6 Dec 2019 22:19:37 +0000 (14:19 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that we've merged late, but for the most part that have
been sitting in -next for a while through platform maintainer trees:
- Fixes to suspend/resume on Tegra, caused by the added features this
merge window
- Cleanups and minor fixes to TI additions this merge window
- Tee fixes queued up late before the merge window, included here.
- A handful of other fixlets
There's also a refresh of the shareed config files (multi_v* on
32-bit, and defconfig on 64-bit), to avoid conflicts when we get new
contributions"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: multi_v7_defconfig: Restore debugfs support
ARM: defconfig: re-run savedefconfig on multi_v* configs
arm64: defconfig: re-run savedefconfig
ARM: pxa: Fix resource properties
soc: mediatek: cmdq: fixup wrong input order of write api
soc: aspeed: Fix snoop_file_poll()'s return type
MAINTAINERS: Switch to Marvell addresses
MAINTAINERS: update Cavium ThunderX drivers
Revert "arm64: dts: juno: add dma-ranges property"
MAINTAINERS: Make Nicolas Saenz Julienne the new bcm2835 maintainer
firmware: arm_scmi: Avoid double free in error flow
arm64: dts: juno: Fix UART frequency
ARM: dts: Fix sgx sysconfig register for omap4
arm: socfpga: execute cold reboot by default
ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
ARM: dts: dra7: fix cpsw mdio fck clock
ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
soc/tegra: pmc: Add reset sources and levels on Tegra194
soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
...
Linus Torvalds [Fri, 6 Dec 2019 22:18:01 +0000 (14:18 -0800)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- ZONE_DMA32 initialisation fix when memblocks fall entirely within the
first GB (used by ZONE_DMA in 5.5 for Raspberry Pi 4).
- Couple of ftrace fixes following the FTRACE_WITH_REGS patchset.
- access_ok() fix for the Tagged Address ABI when called from from a
kernel thread (asynchronous I/O): the kthread does not have the TIF
flags of the mm owner, so untag the user address unconditionally.
- KVM compute_layout() called before the alternatives code patching.
- Minor clean-ups.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry: refine comment of stack overflow check
arm64: ftrace: fix ifdeffery
arm64: KVM: Invoke compute_layout() before alternatives are applied
arm64: Validate tagged addresses in access_ok() called from kernel threads
arm64: mm: Fix column alignment for UXN in kernel_page_tables
arm64: insn: consistently handle exit text
arm64: mm: Fix initialisation of DMA zones on non-NUMA systems
David Howells [Fri, 6 Dec 2019 21:34:51 +0000 (21:34 +0000)]
pipe: Fix iteration end check in fuse_dev_splice_write()
Fix the iteration end check in fuse_dev_splice_write(). The iterator
position can only be compared with == or != since wrappage may be involved.
Fixes: 8cefc107ca54 ("pipe: Use head and tail pointers for the ring, not cursor and length") Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 6 Dec 2019 21:36:31 +0000 (13:36 -0800)]
Merge tag 'powerpc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"A few commits splitting the KASAN instrumented bitops header in three,
to match the split of the asm-generic bitops headers.
This is needed on powerpc because we use the generic bitops for the
non-atomic case only, whereas the existing KASAN instrumented bitops
assume all the underlying operations are provided by the arch as
arch_foo() versions.
Thanks to: Daniel Axtens & Christophe Leroy"
* tag 'powerpc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
docs/core-api: Remove possibly confusing sub-headings from Bit Operations
powerpc: support KASAN instrumentation of bitops
kasan: support instrumented bitops combined with generic bitops
projects / kernel.git / log