Andrew Lunn [Sun, 26 Sep 2021 17:41:26 +0000 (19:41 +0200)]
dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: bf90e25f24c4 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 26 Sep 2021 17:41:25 +0000 (19:41 +0200)]
dsa: mv88e6xxx: Fix MTU definition
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: bf90e25f24c4 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 26 Sep 2021 17:41:24 +0000 (19:41 +0200)]
dsa: mv88e6xxx: 6161: Use chip wide MAX MTU
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: bf90e25f24c4 ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Hagan [Sat, 25 Sep 2021 11:36:27 +0000 (11:36 +0000)]
net: bgmac-platform: handle mac-address deferral
This patch is a replication of Christian Lamparter's "net: bgmac-bcma:
handle deferred probe error due to mac-address" patch for the
bgmac-platform driver [1].
As is the case with the bgmac-bcma driver, this change is to cover the
scenario where the MAC address cannot yet be discovered due to reliance
on an nvmem provider which is yet to be instantiated, resulting in a
random address being assigned that has to be manually overridden.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We observed below report when playing with netlink sock:
UBSAN: shift-out-of-bounds in net/sched/sch_api.c:580:10
shift exponent 249 is too large for 32-bit type
CPU: 0 PID: 685 Comm: a.out Not tainted
Call Trace:
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x4e
__ubsan_handle_shift_out_of_bounds+0x161/0x182
__qdisc_calculate_pkt_len+0xf0/0x190
__dev_queue_xmit+0x2ed/0x15b0
it seems like kernel won't check the stab log value passing from
user, and will use the insane value later to calculate pkt_len.
This patch just add a check on the size/cell_log to avoid insane
calculation.
Reported-by: Abaci <abaci@linux.alibaba.com> Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) ipset limits the max allocatable memory via kvmalloc() to MAX_INT,
from Jozsef Kadlecsik.
2) Check ip_vs_conn_tab_bits value to be in the range specified
in Kconfig, from Andrea Claudi.
3) Initialize fragment offset in ip6tables, from Jeremy Sowden.
4) Make conntrack hash chain length random, from Florian Westphal.
5) Add zone ID to conntrack and NAT hashtuple again, also from Florian.
6) Add selftests for bidirectional zone support and colliding tuples,
from Florian Westphal.
7) Unlink table before synchronize_rcu when cleaning tables with
owner, from Florian.
8) ipset limits the max allocatable memory via kvmalloc() to MAX_INT.
9) Release conntrack entries via workqueue in masquerade, from Florian.
10) Fix bogus net_init in iptables raw table definition, also from Florian.
11) Work around missing softdep in log extensions, from Florian Westphal.
12) Serialize hash resizes and cleanups with mutex, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: conntrack: serialize hash resizes and cleanups
netfilter: log: work around missing softdep backend module
netfilter: iptable_raw: drop bogus net_init annotation
netfilter: nf_nat_masquerade: defer conntrack walk to work queue
netfilter: nf_nat_masquerade: make async masq_inet6_event handling generic
netfilter: nf_tables: Fix oversized kvmalloc() calls
netfilter: nf_tables: unlink table before deleting it
selftests: netfilter: add zone stress test with colliding tuples
selftests: netfilter: add selftest for directional zone support
netfilter: nat: include zone id in nat table hash again
netfilter: conntrack: include zone id in tuple hash again
netfilter: conntrack: make max chain length random
netfilter: ip6_tables: zero-initialize fragment offset
ipvs: check that ip_vs_conn_tab_bits is between 8 and 20
netfilter: ipset: Fix oversized kvmalloc() calls
====================
Aaro Koskinen [Thu, 23 Sep 2021 22:00:16 +0000 (01:00 +0300)]
smsc95xx: fix stalled rx after link change
After commit aba6c7f83541 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: aba6c7f83541 ("smsc95xx: add phylib support") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: Fix rtnexthop len when RTA_FLOW is present
Multipath RTA_FLOW is embedded in nexthop. Dump it in fib_add_nexthop()
to get the length of rtnexthop correct.
Fixes: e2adcfc95725 ("ipv4: Refactor nexthop attributes in fib_dump_info") Signed-off-by: Xiao Liang <shaw.leon@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 23 Sep 2021 13:23:33 +0000 (16:23 +0300)]
net: enetc: fix the incorrect clearing of IF_MODE bits
The enetc phylink .mac_config handler intends to clear the IFMODE field
(bits 1:0) of the PM0_IF_MODE register, but incorrectly clears all the
other fields instead.
For normal operation, the bug was inconsequential, due to the fact that
we write the PM0_IF_MODE register in two stages, first in
phylink .mac_config (which incorrectly cleared out a bunch of stuff),
then we update the speed and duplex to the correct values in
phylink .mac_link_up.
Judging by the code (not tested), it looks like maybe loopback mode was
broken, since this is one of the settings in PM0_IF_MODE which is
incorrectly cleared.
Fixes: 8ec0e3600a8d ("net: enetc: force the RGMII speed and duplex instead of operating in inband mode") Reported-by: Pavel Machek (CIP) <pavel@denx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 24 Sep 2021 09:51:36 +0000 (10:51 +0100)]
Merge branch 'mptcp-fixes'
Mat Martineau says:
====================
mptcp: Bug fixes
This patch set includes two separate fixes for the net tree:
Patch 1 makes sure that MPTCP token searches are always limited to the
appropriate net namespace.
Patch 2 allows userspace to always change the backup settings for
configured endpoints even if those endpoints are not currently in use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp: allow changing the 'backup' bit when no sockets are open
current Linux refuses to change the 'backup' bit of MPTCP endpoints, i.e.
using MPTCP_PM_CMD_SET_FLAGS, unless it finds (at least) one subflow that
matches the endpoint address. There is no reason for that, so we can just
ignore the return value of mptcp_nl_addr_backup(). In this way, endpoints
can reconfigure their 'backup' flag even if no MPTCP sockets are open (or
more generally, in case the MP_PRIO message is not sent out).
Fixes: fb1bfe931400 ("mptcp: add set_flags command in PM netlink") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp_token_get_sock() may return a mptcp socket that is in
a different net namespace than the socket that received the token value.
The mptcp syncookie code path had an explicit check for this,
this moves the test into mptcp_token_get_sock() function.
Eventually token.c should be converted to pernet storage, but
such change is not suitable for net tree.
Fixes: 43daacf018af7 ("mptcp: refactor token container") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ad0fcb1ce11c ("sctp: delay as much as possible skb_linearize") Reported-by: syzbot+581aff2ae6b860625116@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- dsa: bcm_sf2: fix array overrun in bcm_sf2_num_active_ports()
Previous releases - regressions:
- introduce a shutdown method to mdio device drivers, and make DSA
switch drivers compatible with masters disappearing on shutdown;
preventing infinite reference wait
- fix issues in mdiobus users related to ->shutdown vs ->remove
- virtio-net: fix pages leaking when building skb in big mode
- xen-netback: correct success/error reporting for the
SKB-with-fraglist
- dsa: tear down devlink port regions when tearing down the devlink
port on error
- nexthop: fix division by zero while replacing a resilient group
- hns3: check queue, vf, vlan ids range before using
Previous releases - always broken:
- napi: fix race against netpoll causing NAPI getting stuck
- mlx4_en: ensure link operstate is updated even if link comes up
before netdev registration
- bnxt_en: fix TX timeout when TX ring size is set to the smallest
- enetc: fix illegal access when reading affinity_hint; prevent oops
on sysfs access
- core: correct the sock::sk_lock.owned lockdep annotations"
* tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
atlantic: Fix issue in the pm resume flow.
net/mlx4_en: Don't allow aRFS for encapsulated packets
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries
nfc: st-nci: Add SPI ID matching DT compatible
MAINTAINERS: remove Guvenc Gulce as net/smc maintainer
nexthop: Fix memory leaks in nexthop notification chain listeners
mptcp: ensure tx skbs always have the MPTCP ext
qed: rdma - don't wait for resources under hw error recovery flow
s390/qeth: fix deadlock during failing recovery
s390/qeth: Fix deadlock in remove_discipline
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
net: dsa: realtek: register the MDIO bus under devres
net: dsa: don't allocate the slave_mii_bus using devres
Doc: networking: Fox a typo in ice.rst
net: dsa: fix dsa_tree_setup error path
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
net/smc: add missing error check in smc_clc_prfx_set()
net: hns3: fix a return value error in hclge_get_reset_status()
net: hns3: check vlan id before using it
...
Prior to the commit 8c9787b569d0 ("memcg: switch lruvec stats to rstat")
and the commit 8604faa3af29 ("memcg: infrastructure to flush memcg
stats"), each lruvec memcg stats can be off by (nr_cgroups * nr_cpus *
32) at worst and for unbounded amount of time. The commit 8604faa3af29
moved the lruvec stats to rstat infrastructure and the commit 8c9787b569d0 bounded the error for all the lruvec stats to (nr_cpus *
32) at worst for at most 2 seconds. More specifically it decoupled the
number of stats and the number of cgroups from the error rate.
However this reduction in error comes with the cost of triggering the
slowpath of stats update more frequently. Previously in the slowpath
the kernel adds the stats up the memcg tree. After 8604faa3af29, the
kernel triggers the asyn lruvec stats flush through queue_work(). This
causes regression reports from 0day kernel bot [1] as well as from
phoronix test suite [2].
We tried two options to fix the regression:
1) Increase the threshold to trigger the slowpath in lruvec stats
update codepath from 32 to 512.
2) Remove the slowpath from lruvec stats update codepath and instead
flush the stats in the page refault codepath. The assumption is that
the kernel timely flush the stats, so, the update tree would be
small in the refault codepath to not cause the preformance impact.
Following are the results of will-it-scale/page_fault[1|2|3] benchmark
on four settings i.e. (1) 5.15-rc1 as baseline (2) 5.15-rc1 with 8604faa3af29 and 8c9787b569d0 reverted (3) 5.15-rc1 with option-1
(4) 5.15-rc1 with option-2.
From the above result, it seems like the option-2 not only solves the
regression but also improves the performance for at least these
benchmarks.
Feng Tang (intel) ran the aim7 benchmark with these two options and
confirms that option-1 reduces the regression but option-2 removes the
regression.
Michael Larabel (phoronix) ran multiple benchmarks with these options
and reported the results at [3] and it shows for most benchmarks
option-2 removes the regression introduced by the commit 8604faa3af29
("memcg: infrastructure to flush memcg stats").
Based on the experiment results, this patch proposed the option-2 as the
solution to resolve the regression.
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 6f235d164bcc ("atlantic: Fix driver resume flow.") Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Thu, 23 Sep 2021 06:51:45 +0000 (09:51 +0300)]
net/mlx4_en: Don't allow aRFS for encapsulated packets
Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.
Fixes: 1e39d780db50 ("net/mlx4_en: Add accelerated RFS support") Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 23 Sep 2021 02:03:38 +0000 (19:03 -0700)]
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
The blamed commit made the fatally incorrect assumption that ports which
aren't in the FORWARDING STP state should not have packets forwarded
towards them, and that is all that needs to be done.
However, that logic alone permits BLOCKING ports to forward to
FORWARDING ports, which of course allows packet storms to occur when
there is an L2 loop.
The ocelot_get_bridge_fwd_mask should not only ask "what can the bridge
do for you", but "what can you do for the bridge". This way, only
FORWARDING ports forward to the other FORWARDING ports from the same
bridging domain, and we are still compatible with the idea of multiple
bridges.
Fixes: 4b0c7c054d34 ("net: ocelot: support multiple bridges") Suggested-by: Colin Foster <colin.foster@in-advantage.com> Reported-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes multiple CLS_REPLACE calls are issued for the same connection.
rhashtable_insert_fast does not check for these duplicates, so multiple
hardware flow entries can be created.
Fix this by checking for an existing entry early
Fixes: f00009ff5a32 ("net: ethernet: mtk_eth_soc: add flow offloading support") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Wed, 22 Sep 2021 18:30:37 +0000 (19:30 +0100)]
nfc: st-nci: Add SPI ID matching DT compatible
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding the part name used in
the compatible to the list of SPI IDs.
Fixes: 0ce7936ceffc ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
nexthop: Fix memory leaks in nexthop notification chain listeners
syzkaller discovered memory leaks [1] that can be reduced to the
following commands:
# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0
As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.
One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.
Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.
The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.
Fixes: 4e45b8605c99 ("mlxsw: spectrum_router: Add support for nexthop objects") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
init: Revert accidental changes to print irqs_disabled()
Commit 5e8775a8e8f3 ("xsurf100: drop include of lib8390.c") accidentally
changed init/main.c. Revert that part.
Fixes: 5e8775a8e8f3 ("xsurf100: drop include of lib8390.c") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.
Merge tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi modalias fix from Mark Brown:
"Fix modalias issues
As reported by Russell King the change to use OF style modaliases for
DT enumerated broke at least the spi-nor driver, the patch here
reverts that change to fix the regression.
Sadly this will mean that anything that started loading since the
change to OF modaliases will run into issues, there doesn't seem to be
any approach which doesn't cause some problems and thi seems like the
least bad approach - gory details are in the commit log for the
change.
I'm currently working through the SPI drivers to add ID tables and
missing IDs to tables which should address things from the other end,
this seems more straightforward and robust than any other options"
* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Revert modalias changes
Merge tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Critical bug fixes:
- Fix crash in NLM TEST procedure
- NFSv4.1+ backchannel not restored after PATH_DOWN"
* tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: back channel stuck in SEQ4_STATUS_CB_PATH_DOWN
NLM: Fix svcxdr_encode_owner()
Merge tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The first round of bug-fixes for platform-drivers-x86 for 5.15,
highlights:
- amd-pmc fix for some suspend/resume issues
- intel-hid fix to avoid false-positive SW_TABLET_MODE=1 reporting
- some build error/warning fixes
- various DMI quirk additions"
* tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
platform/x86/intel: hid: Add DMI switches allow list
platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
platform/x86: amd-pmc: Increase the response register timeout
platform/x86: touchscreen_dmi: Update info for the Chuwi Hi10 Plus (CWI527) tablet
platform/x86: touchscreen_dmi: Add info for the Chuwi HiBook (CWI514) tablet
lg-laptop: Correctly handle dmi_get_system_info() returning NULL
platform/x86/intel: punit_ipc: Drop wrong use of ACPI_PTR()
Paolo Abeni [Wed, 22 Sep 2021 11:12:17 +0000 (13:12 +0200)]
mptcp: ensure tx skbs always have the MPTCP ext
Due to signed/unsigned comparison, the expression:
info->size_goal - skb->len > 0
evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.
Due to the above, syzbot is able to trigger the following WARN_ON():
Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.
Additionally, ensure that the skb in the tx cache always carries
the relevant extension.
Reported-and-tested-by: syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com Fixes: 2668d5738ac7 ("mptcp: fix possible divide by zero") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: rdma - don't wait for resources under hw error recovery flow
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 5f29a8eff7c5 ("qed: Add infrastructure for error detection and recovery") Signed-off-by: Michal Kalderon <mkalderon@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: Shai Malin <smalin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 22 Sep 2021 03:02:27 +0000 (20:02 -0700)]
Merge branch 's390-qeth-fixes-2021-09-21'
Julian Wiedmann says:
====================
s390/qeth: fixes 2021-09-21
This brings two fixes for deadlocks when a device is removed while it
has certain types of async work pending. And one additional fix for a
missing NULL check in an error case.
====================
Alexandra Winter [Tue, 21 Sep 2021 14:52:17 +0000 (16:52 +0200)]
s390/qeth: fix deadlock during failing recovery
Commit 0b42b521db58 ("s390/qeth: fix deadlock during recovery") removed
taking discipline_mutex inside qeth_do_reset(), fixing potential
deadlocks. An error path was missed though, that still takes
discipline_mutex and thus has the original deadlock potential.
Intermittent deadlocks were seen when a qeth channel path is configured
offline, causing a race between qeth_do_reset and ccwgroup_remove.
Call qeth_set_offline() directly in the qeth_do_reset() error case and
then a new variant of ccwgroup_set_offline(), without taking
discipline_mutex.
Fixes: aec9f46caab2 ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandra Winter [Tue, 21 Sep 2021 14:52:16 +0000 (16:52 +0200)]
s390/qeth: Fix deadlock in remove_discipline
Problem: qeth_close_dev_handler is a worker that tries to acquire
card->discipline_mutex via drv->set_offline() in ccwgroup_set_offline().
Since commit aec9f46caab2
("s390/qeth: fix locking for discipline setup / removal")
qeth_remove_discipline() is called under card->discipline_mutex and
cancels the work and waits for it to finish.
STOPLAN reception with reason code IPA_RC_VEPA_TO_VEB_TRANSITION is the
only situation that schedules close_dev_work. In that situation scheduling
qeth recovery will also result in an offline interface, when resetting the
isolation mode fails, if the external switch is still set to VEB.
And since commit 0b42b521db58 ("s390/qeth: fix deadlock during recovery")
qeth recovery does not aquire card->discipline_mutex anymore.
So we accept the longer pathlength of qeth_schedule_recovery in this
error situation and re-use the existing function.
As a side-benefit this changes the hwtrap to behave like during recovery
instead of like during a user-triggered set_offline.
Fixes: aec9f46caab2 ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Acked-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Fixes: c4463a45afb7 ("s390/qeth: tolerate pre-filled RX buffer") Reported-by: Stefan Raspl <raspl@linux.ibm.com> Root-caused-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mark Brown [Tue, 21 Sep 2021 14:44:06 +0000 (15:44 +0100)]
spi: Revert modalias changes
During the v5.13 cycle we updated the SPI subsystem to generate OF style
modaliases for SPI devices, replacing the old Linux style modalises we
used to generate based on spi_device_id which are the DT style name with
the vendor removed. Unfortunately this means that we start only
reporting OF style modalises and not the old ones and there is nothing
that ensures that drivers list every possible OF compatible string in
their OF ID table. The result is that there are systems which have been
relying on loading modules based on the old style that are now broken,
as found by Russell King with spi-nor on Macchiatobin.
spi-nor is a particularly problematic case for this, it only lists a
single generic DT compatible jedec,spi-nor in the driver but supports a
huge raft of device specific compatibles, with a large set of part
numbers many of which are offered by multiple vendors. Russell's
searches of upstream device trees has turned up examples with vendor
names written in non-standard ways too. To make matters worse up until 79209a6754e5 ("Documentation: devicetree: m25p80: add "nor-jedec"
binding") the generic compatible was not part of the binding so there
are device trees out there written to that binding version which don't
list it all. The sheer number of parts supported together with our
previous approach of ignoring the vendor ID makes robustly fixing this
by adding compatibles to the spi-nor driver seem problematic, the
current DT binding document does not list all the parts supported by the
driver at the minute (further patches will fix this).
I've also investigated supporting both formats of modalias
simultaneously but that doesn't seem possible, especially without
breaking our userspace ABI which is obviously not viable.
This will unfortunately mean that any system which had started having
modules autoload based on the OF compatibles for drivers that list
things there but not in the spi_device_ids will now not have those
modules load which is itself a regression. Since it affects a narrower
time window and the particularly problematic spi-nor driver may be
critical to system boot on smaller systems this seems the best of a
series of bad options. I will start an audit of SPI drivers to identify
and fix cases where things won't autoload using spi_device_id, this is
not great but seems to be the best way forward that anyone has been able
to identify.
Thanks to Russell for both his report and the additional diagnostic and
analysis work he has done here, the detailed research above was his
work.
Fixes: c759c40fe9ae ("spi: update modalias_show after of_device_uevent_modalias support") Fixes: 9e0f5c3de2e0 ("spi: add of_device_uevent_modalias support") Reported-by: Russell King (Oracle) <linux@armlinux.org.uk> Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Mark Brown <broonie@kernel.org> Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Cc: Andreas Schwab <schwab@suse.de> Cc: Marco Felsch <m.felsch@pengutronix.de>
Merge tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 eBPF fixes from Vasily Gorbik:
"Johan Almbladh has implemented a number of new testcases for eBPF [1],
which uncovered three miscompilation issues in the s390 eBPF JIT"
Link: https://lore.kernel.org/bpf/20210902185229.1840281-1-johan.almbladh@anyfinetworks.com/
* tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/bpf: Fix optimizing out zero-extensions
s390/bpf: Fix 64-bit subtraction of the -0x80000000 constant
s390/bpf: Fix branch shortening during codegen pass
In commit d7c5d281d45c ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag. It made the code clearer,
and it seemed to make gcc happy.
However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens. And not necessarily
the rigth one.
End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:
because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it. Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.
This is clearly a gcc bug, but we can work around it fairly easily. The
biggest thing here is the big honking comment about why we do what we
do.
José Expósito [Mon, 20 Sep 2021 16:03:12 +0000 (18:03 +0200)]
platform/x86/intel: hid: Add DMI switches allow list
Some devices, even non convertible ones, can send incorrect
SW_TABLET_MODE reports.
Add an allow list and accept such reports only from devices in it.
Bug reported for Dell XPS 17 9710 on:
https://gitlab.freedesktop.org/libinput/libinput/-/issues/662
Reported-by: Tobias Gurtzick <magic@wizardtales.com> Suggested-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Tobias Gurtzick <magic@wizardtales.com> Signed-off-by: José Expósito <jose.exposito89@gmail.com> Link: https://lore.kernel.org/r/20210920160312.9787-1-jose.exposito89@gmail.com
[hdegoede@redhat.com: Check dmi_switches_auto_add_allow_list only once] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.
ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'
Fixes: cde9c53c2663 ("platform/x86: dell-privacy: Add support for Dell hardware privacy") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Perry Yuan <Perry.Yuan@dell.com> Cc: Dell.Client.Kernel@dell.com Cc: platform-driver-x86@vger.kernel.org Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <mgross@linux.intel.com> Link: https://lore.kernel.org/r/20210918044829.19222-1-rdunlap@infradead.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
David S. Miller [Tue, 21 Sep 2021 12:52:16 +0000 (13:52 +0100)]
Merge branch 'dsa-devres'
Vladimir Oltean says:
====================
Fix mdiobus users with devres
Commit 50298441a391 ("net: phy: don't abuse devres in
devm_mdiobus_register()") by Bartosz Golaszewski has introduced two
classes of potential bugs by making the devres callback of
devm_mdiobus_alloc stop calling mdiobus_unregister.
The exact buggy circumstances are presented in the individual commit
messages. I have searched the tree for other occurrences, but at the
moment:
- for issue (a) I have no concrete proof that other buses except SPI and
I2C suffer from it, and the only SPI or I2C device drivers that call
of_mdiobus_alloc are the DSA drivers that leave a NULL
ds->slave_mii_bus and a non-NULL ds->ops->phy_read, aka ksz9477,
ksz8795, lan9303_i2c, vsc73xx-spi.
- for issue (b), all drivers which call of_mdiobus_alloc either use
of_mdiobus_register too, or call mdiobus_unregister sometime within
the ->remove path.
Although at this point I've seen enough strangeness caused by this
"device_del during ->shutdown" that I'm just going to copy the SPI and
I2C subsystem maintainers to this patch series, to get their feedback
whether they've had reports about things like this before. I don't think
other buses behave in this way, it forces SPI and I2C devices to have to
protect themselves from a really strange set of issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 21:42:09 +0000 (00:42 +0300)]
net: dsa: realtek: register the MDIO bus under devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes: 50298441a391 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 21:42:08 +0000 (00:42 +0300)]
net: dsa: don't allocate the slave_mii_bus using devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: 50298441a391 ("net: phy: don't abuse devres in devm_mdiobus_register()") Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 20 Sep 2021 22:49:18 +0000 (01:49 +0300)]
net: dsa: fix dsa_tree_setup error path
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes: 654b5502be55 ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: e11c5a689e7e ("net/smc: handle incoming CDC validation message") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: log: work around missing softdep backend module
iptables/nftables has two types of log modules:
1. backend, e.g. nf_log_syslog, which implement the functionality
2. frontend, e.g. xt_LOG or nft_log, which call the functionality
provided by backend based on nf_tables or xtables rule set.
Problem is that the request_module() call to load the backed in
nf_logger_find_get() might happen with nftables transaction mutex held
in case the call path is via nf_tables/nft_compat.
This can cause deadlocks (see 'Fixes' tags for details).
The chosen solution as to let modprobe deal with this by adding 'pre: '
soft dep tag to xt_LOG (to load the syslog backend) and xt_NFLOG (to
load nflog backend).
Eric reports that this breaks on systems with older modprobe that
doesn't support softdeps.
Another, similar issue occurs when someone either insmods xt_(NF)LOG
directly or unloads the backend module (possible if no log frontend
is in use): because the frontend module is already loaded, modprobe is
not invoked again so the softdep isn't evaluated.
Add a workaround: If nf_logger_find_get() returns -ENOENT and call
is not via nft_compat, load the backend explicitly and try again.
Else, let nft_compat ask for deferred request_module via nf_tables
infra.
Softdeps are kept in-place, so with newer modprobe the dependencies
are resolved from userspace.
Fixes: 27b54025fed7 ("netfilter: nft_log: perform module load from nf_tables") Fixes: f7d77a26bb74 ("netfilter: nf_log: add module softdeps") Reported-and-tested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_nat_masquerade: make async masq_inet6_event handling generic
masq_inet6_event is called asynchronously from system work queue,
because the inet6 notifier is atomic and nf_iterate_cleanup can sleep.
The ipv4 and device notifiers call nf_iterate_cleanup directly.
This is legal, but these notifiers are called with RTNL mutex held.
A large conntrack table with many devices coming and going will have severe
impact on the system usability, with 'ip a' blocking for several seconds.
This change places the defer code into a helper and makes it more
generic so ipv4 and ifdown notifiers can be converted to defer the
cleanup walk as well in a follow patch.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Problem is that all get operations are lockless, so the commit_mutex
held by nft_rcv_nl_event() isn't enough to stop a parallel GET request
from doing read-accesses to the table object even after synchronize_rcu().
To avoid this, unlink the table first and store the table objects in
on-stack scratch space.
selftests: netfilter: add zone stress test with colliding tuples
Add 20k entries to the connection tracking table, once from the
data plane, once via ctnetlink.
In both cases, each entry lives in a different conntrack zone
and addresses/ports are identical.
Expectation is that insertions work and occurs in constant time:
PASS: added 10000 entries in 1215 ms (now 10000 total, loop 1)
PASS: added 10000 entries in 1214 ms (now 20000 total, loop 2)
PASS: inserted 20000 entries from packet path in 2434 ms total
PASS: added 10000 entries in 57631 ms (now 10000 total)
PASS: added 10000 entries in 58572 ms (now 20000 total)
PASS: inserted 20000 entries via ctnetlink in 116205 ms
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
selftests: netfilter: add selftest for directional zone support
Add a script to exercise NAT port clash resolution with directional zones.
Add net namespaces that use the same IP address and connect them to a
gateway.
Gateway uses policy routing based on iif/mark and conntrack zones to
isolate the client namespaces. In server direction, same zone with NAT
to single address is used.
Then, connect to a server from each client netns, using identical
connection id, i.e. saddr:sport -> daddr:dport.
Expectation is for all connections to succeeed: NAT gatway is
supposed to do port reallocation for each of the (clashing) connections.
This is based on the description/use case provided in the commit message of beb5cbd91fb55d ("netfilter: nf_conntrack: add direction support for zones").
Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: conntrack: include zone id in tuple hash again
commit beb5cbd91fb55d ("netfilter: nf_conntrack: add direction support for zones")
removed the zone id from the hash value.
This has implications on hash chain lengths with overlapping tuples, which
can hit 64k entries on released kernels, before upper droplimit was added
in 280638bee62 ("netfilter: refuse insertion if chain has grown too large").
With that change reverted, test script coming with this series shows
linear insertion time growth:
10000 entries in 3737 ms (now 10000 total, loop 1)
10000 entries in 16994 ms (now 20000 total, loop 2)
10000 entries in 47787 ms (now 30000 total, loop 3)
10000 entries in 72731 ms (now 40000 total, loop 4)
10000 entries in 95761 ms (now 50000 total, loop 5)
10000 entries in 96809 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 333825 ms
There are three supported zone use cases:
1. Connection is in the default zone (zone 0).
This means to special config (the default).
2. Connection is in a different zone (1 to 2**16).
This means rules are in place to put packets in
the desired zone, e.g. derived from vlan id or interface.
3. Original direction is in zone X and Reply is in zone 0.
3) allows to use of the existing NAT port collision avoidance to provide
connectivity to internet/wan even when the various zones have overlapping
source networks separated via policy routing.
In case the original zone is 0 all three cases are identical.
There is no way to place original direction in zone x and reply in
zone y (with y != 0).
Zones need to be assigned manually via the iptables/nftables ruleset,
before conntrack lookup occurs (raw table in iptables) using the
"CT" target conntrack template support
(-j CT --{zone,zone-orig,zone-reply} X).
Normally zone assignment happens based on incoming interface, but could
also be derived from packet mark, vlan id and so on.
This means that when case 3 is used, the ruleset will typically not even
assign a connection tracking template to the "reply" packets, so lookup
happens in zone 0.
However, it is possible that reply packets also match a ct zone
assignment rule which sets up a template for zone X (X > 0) in original
direction only.
Therefore, after making the zone id part of the hash, we need to do a
second lookup using the reply zone id if we did not find an entry on
the first lookup.
In practice, most deployments will either not use zones at all or the
origin and reply zones are the same, no second lookup is required in
either case.
After this change, packet path insertion test passes with constant
insertion times:
10000 entries in 1064 ms (now 10000 total, loop 1)
10000 entries in 1074 ms (now 20000 total, loop 2)
10000 entries in 1066 ms (now 30000 total, loop 3)
10000 entries in 1079 ms (now 40000 total, loop 4)
10000 entries in 1081 ms (now 50000 total, loop 5)
10000 entries in 1082 ms (now 60000 total, loop 6)
inserted 60000 entries from packet path in 6452 ms
Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Merge tag 'afs-fixes-20210913' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
"Fixes for AFS problems that can cause data corruption due to
interaction with another client modifying data cached locally:
- When d_revalidating a dentry, don't look at the inode to which it
points. Only check the directory to which the dentry belongs. This
was confusing things and causing the silly-rename cleanup code to
remove the file now at the dentry of a file that got deleted.
- Fix mmap data coherency. When a callback break is received that
relates to a file that we have cached, the data content may have
been changed (there are other reasons, such as the user's rights
having been changed). However, we're checking it lazily, only on
entry to the kernel, which doesn't happen if we have a writeable
shared mapped page on that file.
We make the kernel keep track of mmapped files and clear all PTEs
mapping to that file as soon as the callback comes in by calling
unmap_mapping_pages() (we don't necessarily want to zap the
pagecache). This causes the kernel to be reentered when userspace
tries to access the mmapped address range again - and at that point
we can query the server and, if we need to, zap the page cache.
Ideally, I would check each file at the point of notification, but
that involves poking the server[*] - which is holding an exclusive
lock on the vnode it is changing, waiting for all the clients it
notified to reply. This could then deadlock against the server.
Further, invalidating the pagecache might call ->launder_page(),
which would try to write to the file, which would definitely
deadlock. (AFS doesn't lease file access).
[*] Checking to see if the file content has changed is a matter of
comparing the current data version number, but we have to ask
the server for that. We also need to get a new callback promise
and we need to poke the server for that too.
- Add some more points at which the inode is validated, since we're
doing it lazily, notably in ->read_iter() and ->page_mkwrite(), but
also when performing some directory operations.
Ideally, checking in ->read_iter() would be done in some derivation
of filemap_read(). If we're going to call the server to read the
file, then we get the file status fetch as part of that.
- The above is now causing us to make a lot more calls to
afs_validate() to check the inode - and afs_validate() takes the
RCU read lock each time to make a quick check (ie.
afs_check_validity()). This is entirely for the purpose of checking
cb_s_break to see if the server we're using reinitialised its list
of callbacks - however this isn't a very common event, so most of
the time we're taking this needlessly.
Add a new cell-wide counter to count the number of
reinitialisations done by any server and check that - and only if
that changes, take the RCU read lock and check the server list (the
server list may change, but the cell a file is part of won't).
- Don't update vnode->cb_s_break and ->cb_v_break inside the validity
checking loop. The cb_lock is done with read_seqretry, so we might
go round the loop a second time after resetting those values - and
that could cause someone else checking validity to miss something
(I think).
Also included are patches for fixes for some bugs encountered whilst
debugging this:
- Fix a leak of afs_read objects and fix a leak of keys hidden by
that.
- Fix a leak of pages that couldn't be added to extend a writeback.
- Fix the maintenance of i_blocks when i_size is changed by a local
write or a local dir edit"
Merge tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd
Pull ksmbd server fixes from Steve French:
"Three ksmbd fixes, including an important security fix for path
processing, and a buffer overflow check, and a trivial fix for
incorrect header inclusion"
* tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd:
ksmbd: add validation for FILE_FULL_EA_INFORMATION of smb2_get_info
ksmbd: prevent out of share access
ksmbd: transport_rdma: Don't include rwlock.h directly
Merge tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
- two deferred close fixes (for bugs found with xfstests 478 and 461)
- a deferred close improvement in rename
- two trivial fixes for incorrect Linux comment formatting of multiple
cifs files (pointed out by automated kernel test robot and
checkpatch)
* tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Not to defer close on file when lock is set
cifs: Fix soft lockup during fsstress
cifs: Deferred close performance improvements
cifs: fix incorrect kernel doc comments
cifs: remove pathname for file from SPDX header
Merge tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark BrownL
"This contains a couple of fixes, one fix for handling of zero length
transfers on Rockchip devices and a warning fix which will conflict
with a version you did but cleans up some extra unneeded forward
declarations as well which seems a bit neater"
* tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: tegra20-slink: Declare runtime suspend and resume functions conditionally
spi: rockchip: handle zero length transfers without timing out
Merge tag 'regulator-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small device specific fixes that have been sent since the
merge window, neither of which stands out particularly"
* tag 'regulator-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max14577: Revert "regulator: max14577: Add proper module aliases strings"
regulator: qcom-rpmh-regulator: fix pm8009-1 ldo7 resource name
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: cbcba4a359a0 ("drm/nouveau: expose pstate selection per-power source in sysfs") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparc64: fix pci_iounmap() when CONFIG_PCI is not set
Guenter reported [1] that the pci_iounmap() changes remain problematic,
with sparc64 allnoconfig and tinyconfig still not building due to the
header file changes and confusion with the arch-specific pci_iounmap()
implementation.
I'm pretty convinced that sparc should just use GENERIC_IOMAP instead of
doing its own thing, since it turns out that the sparc64 version of
pci_iounmap() is somewhat buggy (see [2]). But in the meantime, this
just fixes the build by avoiding the trivial re-definition of the empty
case.
Yufeng Mo [Wed, 15 Sep 2021 13:52:11 +0000 (21:52 +0800)]
net: hns3: fix a return value error in hclge_get_reset_status()
hclge_get_reset_status() should return the tqp reset status.
However, if the CMDQ fails, the caller will take it as tqp reset
success status by mistake. Therefore, uses a parameters to get
the tqp reset status instead.
Fixes: 575d84053c84 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The input parameters may not be reliable, so check the vlan id before
using it, otherwise may set wrong vlan id into hardware.
Fixes: 87d9446f883d ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls") Signed-off-by: liaoguojia <liaoguojia@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 15 Sep 2021 13:52:09 +0000 (21:52 +0800)]
net: hns3: check queue id range before using
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes: 66f95ea3ecc3 ("net: hns3: refactor the mailbox message between PF and VF") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: fix misuse vf id and vport id in some logs
vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs.
So the actual vf id is equal to vport_id minus 1.
Some VF print logs are actually vport, and logs of vf id actually use
vport id, so this patch fixes them.
Fixes: d2b36c04638e ("net: hns3: change print level of RAS error log from warning to error") Fixes: d143a4dedad4 ("net: hns3: cleanup some print format warning") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The vf id from ethtool is added 1 before configured to driver.
So it's necessary to minus 1 when printing it, in order to
keep consistent with user's configuration.
Fixes: 20dd70e1a57b ("net: hns3: Add support for rule add/delete for flow director") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes: 575d84053c84 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: bd63e1a195d2 ("net: hns3: Add RSS general configuration support for VF") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_register_i2c':
ptp_ocp.c:(.text+0xcc0): undefined reference to `__clk_hw_register_fixed_rate'
arm-linux-gnueabi-ld: ptp_ocp.c:(.text+0xcf4): undefined reference to `devm_clk_hw_register_clkdev'
arm-linux-gnueabi-ld: drivers/ptp/ptp_ocp.o: in function `ptp_ocp_detach':
ptp_ocp.c:(.text+0x1c24): undefined reference to `clk_hw_unregister_fixed_rate'
Fixes: 522a6dc2376f ("ptp: Add clock driver for the OpenCompute TimeCard.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 20 Sep 2021 06:51:52 +0000 (02:51 -0400)]
bnxt_en: Fix TX timeout when TX ring size is set to the smallest
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: 93658deae41f ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadocm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nexthop: Fix division by zero while replacing a resilient group
The resilient nexthop group torture tests in fib_nexthop.sh exposed a
possible division by zero while replacing a resilient group [1]. The
division by zero occurs when the data path sees a resilient nexthop
group with zero buckets.
The tests replace a resilient nexthop group in a loop while traffic is
forwarded through it. The tests do not specify the number of buckets
while performing the replacement, resulting in the kernel allocating a
stub resilient table (i.e, 'struct nh_res_table') with zero buckets.
This table should never be visible to the data path, but the old nexthop
group (i.e., 'oldg') might still be used by the data path when the stub
table is assigned to it.
Fix this by only assigning the stub table to the old nexthop group after
making sure the group is no longer used by the data path.
Cc: stable@vger.kernel.org Fixes: a1797fef5912 ("nexthop: Add implementation of resilient next-hop groups") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
(1) Here return direct. Because of NAPI_STATE_NPSVC exists.
(2) NAPI_STATE_SCHED exists. So not add napi.poll_list to sd->poll_list
Since NAPI_STATE_SCHED already exists and napi is not in the
sd->poll_list queue, NAPI_STATE_SCHED cannot be cleared and will always
exist.
1. This will cause this queue to no longer receive packets.
2. If you encounter napi_disable under the protection of rtnl_lock, it
will cause the entire rtnl_lock to be locked, affecting the overall
system.
This patch uses cmpxchg to implement napi_enable(), which ensures that
there will be no race due to the separation of clear two bits.
Fixes: 8df8097a7ef95b ("netpoll: Close race condition between poll_one_napi and napi_disable") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
pci_iounmap'2: Electric Boogaloo: try to make sense of it all
Nathan Chancellor reports that the recent change to pci_iounmap in
commit 5c1ac0686664 ("parisc: Declare pci_iounmap() parisc version only
when CONFIG_PCI enabled") causes build errors on arm64.
It took me about two hours to convince myself that I think I know what
the logic of that mess of #ifdef's in the <asm-generic/io.h> header file
really aim to do, and rewrite it to be easier to follow.
Famous last words.
Anyway, the code has now been lifted from that grotty header file into
lib/pci_iomap.c, and has fairly extensive comments about what the logic
is. It also avoids indirecting through another confusing (and badly
named) helper function that has other preprocessor config conditionals.
Let's see what odd architecture did something else strange in this area
to break things. But my arm64 cross build is clean.
Fixes: 5c1ac0686664 ("parisc: Declare pci_iounmap() parisc version only when CONFIG_PCI enabled") Reported-by: Nathan Chancellor <nathan@kernel.org> Cc: Helge Deller <deller@gmx.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Ulrich Teichert <krypton@ulrich-teichert.org> Cc: James Bottomley <James.Bottomley@hansenpartnership.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'x86_urgent_for_v5.15_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Prevent a infinite loop in the MCE recovery on return to user space,
which was caused by a second MCE queueing work for the same page and
thereby creating a circular work list.
- Make kern_addr_valid() handle existing PMD entries, which are marked
not present in the higher level page table, correctly instead of
blindly dereferencing them.
- Pass a valid address to sanitize_phys(). This was caused by the
mixture of inclusive and exclusive ranges. memtype_reserve() expect
'end' being exclusive, but sanitize_phys() wants it inclusive. This
worked so far, but with end being the end of the physical address
space the fail is exposed.
- Increase the maximum supported GPIO numbers for 64bit. Newer SoCs
exceed the previous maximum.
* tag 'x86_urgent_for_v5.15_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Avoid infinite loop for copy from user recovery
x86/mm: Fix kern_addr_valid() to cope with existing but not present entries
x86/platform: Increase maximum GPIO number for X86_64
x86/pat: Pass valid address to sanitize_phys()
Merge tag 'perf-urgent-2021-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf event fix from Thomas Gleixner:
"A single fix for the perf core where a value read with READ_ONCE() was
checked and then reread which makes all the checks invalid. Reuse the
already read value instead"
* tag 'perf-urgent-2021-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
events: Reuse value read using READ_ONCE instead of re-reading it
Merge tag 'locking-urgent-2021-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of updates for the RT specific reader/writer locking base code:
- Make the fast path reader ordering guarantees correct.
- Code reshuffling to make the fix simpler"
[ This plays ugly games with atomic_add_return_release() because we
don't have a plain atomic_add_release(), and should really be cleaned
up, I think - Linus ]
* tag 'locking-urgent-2021-09-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwbase: Take care of ordering guarantee for fastpath reader
locking/rwbase: Extract __rwbase_write_trylock()
locking/rwbase: Properly match set_and_save_state() to restore_state()
Merge tag 'powerpc-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix crashes when scv (System Call Vectored) is used to make a syscall
when a transaction is active, on Power9 or later.
- Fix bad interactions between rfscv (Return-from scv) and Power9
fake-suspend mode.
- Fix crashes when handling machine checks in LPARs using the Hash MMU.
- Partly revert a recent change to our XICS interrupt controller code,
which broke the recently added Microwatt support.
Thanks to Cédric Le Goater, Eirik Fuller, Ganesh Goudar, Gustavo Romero,
Joel Stanley, Nicholas Piggin.
* tag 'powerpc-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/xics: Set the IRQ chip data for the ICS native backend
powerpc/mce: Fix access error in mce handler
KVM: PPC: Book3S HV: Tolerate treclaim. in fake-suspend mode changing registers
powerpc/64s: system call rfscv workaround for TM bugs
selftests/powerpc: Add scv versions of the basic TM syscall tests
powerpc/64s: system call scv tabort fix for corrupt irq soft-mask state
Merge tag 'kbuild-fixes-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix bugs in checkkconfigsymbols.py
- Fix missing sys import in gen_compile_commands.py
- Fix missing FORCE warning for ARCH=sh builds
- Fix -Wignored-optimization-argument warnings for Clang builds
- Turn -Wignored-optimization-argument into an error in order to stop
building instead of sprinkling warnings
* tag 'kbuild-fixes-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Add -Werror=ignored-optimization-argument to CLANG_FLAGS
x86/build: Do not add -falign flags unconditionally for clang
kbuild: Fix comment typo in scripts/Makefile.modpost
sh: Add missing FORCE prerequisites in Makefile
gen_compile_commands: fix missing 'sys' package
checkkconfigsymbols.py: Remove skipping of help lines in parse_kconfig_file
checkkconfigsymbols.py: Forbid passing 'HEAD' to --commit
Merge tag 'perf-tools-fixes-for-v5.15-2021-09-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix ip display in 'perf script' when output type != attr->type.
- Ignore deprecation warning when using libbpf'sg btf__get_from_id(),
fixing the build with libbpf v0.6+.
- Make use of FD() robust in libperf, fixing a segfault with 'perf stat
--iostat list'.
- Initialize addr_location:srcline pointer to NULL when resolving
callchain addresses.
- Fix fused instruction logic for assembly functions in 'perf
annotate'.
* tag 'perf-tools-fixes-for-v5.15-2021-09-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf bpf: Ignore deprecation warning when using libbpf's btf__get_from_id()
libperf evsel: Make use of FD robust.
perf machine: Initialize srcline string member in add_location struct
perf script: Fix ip display when type != attr->type
perf annotate: Fix fused instr logic for assembly functions
dmascc: use proper 'virt_to_bus()' rather than casting to 'int'
The old dmascc driver depends on the legacy ISA_DMA_API, and blindly
just casts the kernel virtual address to 'int' for set_dma_addr().
That works only incidentally, and because the high bits of the address
will be ignored anyway. And on 64-bit architectures it causes warnings.
Admittedly, 64-bit architectures with ISA are basically dead - I think
the only example of this is alpha, and nobody would ever use the dmascc
driver there. But hey, the fix is easy enough, the end result is
cleaner, and it's yet another configuration that now builds without
warnings.
If somebody actually uses this driver on an alpha and this fixes it for
you, please email me. Because that is just incredibly bizarre.
With the previous commit (5c1ac0686664: "parisc: Declare pci_iounmap()
parisc version only when CONFIG_PCI enabled") we can now enable
GENERIC_PCI_IOMAP unconditionally on alpha, and if PCI is not enabled we
will just get the nice empty helper functions that allow mixed-bus
drivers to build.
Example driver: the old 3com/3c59x.c driver works with either the PCI or
the EISA version of the 3x59x card, but wouldn't build in an EISA-only
configuration because of missing pci_iomap() and pci_iounmap() dummy
wrappers.
Most of the other PCI infrastructure just becomes empty wrappers even
without GENERIC_PCI_IOMAP, and it's not obvious that the pci_iomap
functionality shouldn't do the same, but this works.
parisc: Declare pci_iounmap() parisc version only when CONFIG_PCI enabled
Linus noticed odd declaration rules for pci_iounmap() in iomap.h and
pci_iomap.h, where it dependend on either NO_GENERIC_PCI_IOPORT_MAP or
GENERIC_IOMAP when CONFIG_PCI was disabled.
Testing on parisc seems to indicate that we need pci_iounmap() only when
CONFIG_PCI is enabled, so the declaration of pci_iounmap() can be moved
cleanly into pci_iomap.h in sync with the declarations of pci_iomap().
Sudip Mukherjee reports that this broke pulseaudio with a NULL pointer
dereference in vc4_hdmi_audio_prepare(), bisected it to this commit, and
confirmed that a revert fixed the problem.
de7105a4047d ("drm/vc4: hdmi: Make sure the controller is powered in detect") 594db0d6bbe4 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
as Michael Stapelberg reports that the new runtime PM changes cause his
Raspberry Pi 3 to hang on boot, probably due to interactions with other
changes in the DRM tree (because a bisect points to the merge in commit 3f9a1b8768b0: "Merge tag 'drm-next-2021-07-01' of git://.../drm").
Revert these two commits until it's been resolved.
selftests: net: af_unix: Fix makefile to use TEST_GEN_PROGS
Makefile uses TEST_PROGS instead of TEST_GEN_PROGS to define
executables. TEST_PROGS is for shell scripts that need to be
installed and run by the common lib.mk framework. The common
framework doesn't touch TEST_PROGS when it does build and clean.
As a result "make kselftest-clean" and "make clean" fail to remove
executables. Run and install work because the common framework runs
and installs TEST_PROGS. Build works because the Makefile defines
"all" rule which is unnecessary if TEST_GEN_PROGS is used.
Use TEST_GEN_PROGS so the common framework can handle build/run/
install/clean properly.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Lama Kayal [Sun, 19 Sep 2021 11:55:45 +0000 (14:55 +0300)]
net/mlx4_en: Resolve bad operstate value
Any link state change that's done prior to net device registration
isn't reflected on the state, thus the operational state is left
obsolete, with 'UNKNOWN' status.
To resolve the issue, query link state from FW upon open operations
to ensure operational state is updated.
Fixes: eebe24d1aff7 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC") Signed-off-by: Lama Kayal <lkayal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: net: af_unix: Fix incorrect args in test result msg
Fix the args to fprintf(). Splitting the message ends up passing
incorrect arg for "sigurg %d" and an extra arg overall. The test
result message ends up incorrect.
test_unix_oob.c: In function ‘main’:
test_unix_oob.c:274:43: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘char *’ [-Wformat=]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
| ~^
| |
| int
| %s
275 | "atmark %d\n", signal_recvd, len, oob, atmark);
| ~~~~~~~~~~~~~
| |
| char *
test_unix_oob.c:274:19: warning: too many arguments for format [-Wformat-extra-args]
274 | fprintf(stderr, "Test 3 failed, sigurg %d len %d OOB %c ",
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log