Linus Torvalds [Sat, 9 Oct 2021 17:17:17 +0000 (10:17 -0700)]
Merge tag '5.15-rc4-ksmbd-fixes' of git://git.samba.org/ksmbd
Pull ksmbd fixes from Steve French:
"Six fixes for the ksmbd kernel server, including two additional
overflow checks, a fix for oops, and some cleanup (e.g. remove dead
code for less secure dialects that has been removed)"
* tag '5.15-rc4-ksmbd-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix oops from fuse driver
ksmbd: fix version mismatch with out of tree
ksmbd: use buf_data_size instead of recalculation in smb3_decrypt_req()
ksmbd: remove the leftover of smb2.0 dialect support
ksmbd: check strictly data area in ksmbd_smb2_check_message()
ksmbd: add the check to vaildate if stream protocol length exceeds maximum value
Linus Torvalds [Sat, 9 Oct 2021 16:07:58 +0000 (09:07 -0700)]
Merge tag 'riscv-for-linus-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of fixes (along with the necessory cleanup) to our VDSO, to
avoid a locking during OOM and to prevent the text from overflowing
into the data page
- A fix to checksyscalls to teach it about our rv32 UABI
- A fix to add clone3() to the rv32 UABI, which was pointed out by
checksyscalls
- A fix to properly flush the icache on the local CPU in addition to
the remote CPUs
* tag 'riscv-for-linus-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
checksyscalls: Unconditionally ignore fstat{,at}64
riscv: Flush current cpu icache before other cpus
RISC-V: Include clone3() on rv32
riscv/vdso: make arch_setup_additional_pages wait for mmap_sem for write killable
riscv/vdso: Move vdso data page up front
riscv/vdso: Refactor asm/vdso.h
Linus Torvalds [Fri, 8 Oct 2021 23:46:09 +0000 (16:46 -0700)]
Merge tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix potential memory leak on a error path in eBPF
- Fix handling of zpci device on reserve
* tag 's390-5.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix zpci_zdev_put() on reserve
bpf, s390: Fix potential memory leak about jit_data
Linus Torvalds [Fri, 8 Oct 2021 20:05:39 +0000 (13:05 -0700)]
Merge tag 'xtensa-20211008' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix build/boot issues caused by CONFIG_OF vs CONFIC_USE_OF usage
- fix reset handler for xtfpga boards
* tag 'xtensa-20211008' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: xtfpga: Try software restart before simulating CPU reset
xtensa: xtfpga: use CONFIG_USE_OF instead of CONFIG_OF
xtensa: call irqchip_init only when CONFIG_USE_OF is selected
xtensa: use CONFIG_USE_OF instead of CONFIG_OF
Linus Torvalds [Fri, 8 Oct 2021 19:55:23 +0000 (12:55 -0700)]
Merge tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- fix two minor issues in the Xen privcmd driver plus a cleanup patch
for that driver
- fix multiple issues related to running as PVH guest and some related
earlyprintk fixes for other Xen guest types
- fix an issue introduced in 5.15 the Xen balloon driver
* tag 'for-linus-5.15b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix cancelled balloon action
xen/x86: adjust data placement
x86/PVH: adjust function/data placement
xen/x86: hook up xen_banner() also for PVH
xen/x86: generalize preferred console model from PV to PVH Dom0
xen/x86: make "earlyprintk=xen" work for HVM/PVH DomU
xen/x86: allow "earlyprintk=xen" to work for PV Dom0
xen/x86: make "earlyprintk=xen" work better for PVH Dom0
xen/x86: allow PVH Dom0 without XEN_PV=y
xen/x86: prevent PVH type from getting clobbered
xen/privcmd: drop "pages" parameter from xen_remap_pfn()
xen/privcmd: fix error handling in mmap-resource processing
xen/privcmd: replace kcalloc() by kvcalloc() when allocating empty pages
Linus Torvalds [Fri, 8 Oct 2021 18:57:54 +0000 (11:57 -0700)]
Merge tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Linus Torvalds [Fri, 8 Oct 2021 18:49:30 +0000 (11:49 -0700)]
Merge tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent ACPI-related regression in the PCI subsystem that
introduced a NULL pointer dereference possible to trigger from
user space via sysfs on some systems"
* tag 'acpi-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
Linus Torvalds [Fri, 8 Oct 2021 17:08:58 +0000 (10:08 -0700)]
Merge tag 'mmc-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes:
- meson-gx: Fix read/write access for dram-access-quirk
- sdhci-of-at91: Fix calibration sequence"
* tag 'mmc-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: meson-gx: do not use memcpy_to/fromio for dram-access-quirk
mmc: sdhci-of-at91: replace while loop with read_poll_timeout
mmc: sdhci-of-at91: wait for calibration done before proceed
Linus Torvalds [Fri, 8 Oct 2021 16:58:50 +0000 (09:58 -0700)]
Merge tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"I've returned from my tropical island retreat, even managed to bring
one of my kids on a dive with some turtles. Thanks to Daniel for doing
last week's work.
Otherwise this is the weekly fixes pull, it's a bit bigger because the
vc4 reverts in your tree caused some problems with fixes in the
drm-misc tree so it got left out last week, so this week has the misc
fixes rebased without the vc4 pieces.
Otherwise it's i915, amdgpu with the usual fixes and a scattering over
other drivers.
I expect things should calm down a bit more next week.
core:
- Kconfig fix for fb_simple vs simpledrm.
i915:
- Fix RKL HDMI audio
- Fix runtime pm imbalance on i915_gem_shrink() error path
- Fix Type-C port access before hw/sw state sync
- Fix VBT backlight struct version/size check
- Fix VT-d async flip on SKL/BXT with plane stretch workaround
* tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drm: (33 commits)
drm/amd/display: Fix detection of 4 lane for DPALT
drm/amd/display: Limit display scaling to up to 4k for DCN 3.1
drm/amd/display: Skip override for preferred link settings during link training
drm/nouveau/debugfs: fix file release memory leak
drm/nouveau/kms/nv50-: fix file release memory leak
drm/nouveau: avoid a use-after-free when BO init fails
DRM: delete DRM IRQ legacy midlayer docs
video: fbdev: gbefb: Only instantiate device when built for IP32
fbdev: simplefb: fix Kconfig dependencies
drm/panel: abt-y030xx067a: yellow tint fix
dt-bindings: panel: ili9341: correct indentation
drm/nouveau/fifo/ga102: initialise chid on return from channel creation
drm/rockchip: Update crtc fixup to account for fractional clk change
drm/nouveau/ga102-: support ttm buffer moves via copy engine
drm/nouveau/kms/tu102-: delay enabling cursor until after assign_windows
drm/sun4i: dw-hdmi: Fix HDMI PHY clock setup
drm/vc4: hdmi: Remove unused struct
drm/kmb: Enable alpha blended second plane
drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume
drm/amdgpu: init iommu after amdkfd device init
...
Dave Airlie [Fri, 8 Oct 2021 01:34:31 +0000 (11:34 +1000)]
Merge tag 'drm-misc-fixes-2021-10-06' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Rebased drm-misc-fixes for v5.15-rc5:
- Dropped vc4 patches.
- Compiler fix for vc4.
- Cursor fix for nouveau.
- Fix ttm buffer moves for ampere gpu's by adding minimal acceleration support.
- Small rockchip fixes.
- Fix DT bindings indent for ili9341.
- Fix y030xx067a init sequence to not get a yellow tint.
- Kconfig fix for fb_simple vs simpledrm.
- Assorted nouvaeu memory leaks.
- Fix gbefb when built with COMPILE_TEST.
These can be replaced by statx(). Since rv32 has a 64-bit time_t we
just never ended up with them in the first place. This is now an error
due to -Werror.
Linus Torvalds [Thu, 7 Oct 2021 21:11:40 +0000 (14:11 -0700)]
Merge tag 'nfsd-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Bug fixes for NFSD error handling paths"
* tag 'nfsd-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Keep existing listeners on portlist error
SUNRPC: fix sign error causing rpcsec_gss drops
nfsd: Fix a warning for nfsd_file_close_inode
nfsd4: Handle the NFSv4 READDIR 'dircount' hint being zero
nfsd: fix error handling of register_pernet_subsys() in init_nfsd()
Linus Torvalds [Thu, 7 Oct 2021 21:01:29 +0000 (14:01 -0700)]
Merge tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
Arnd Bergmann [Thu, 7 Oct 2021 19:14:12 +0000 (21:14 +0200)]
Merge tag 'asahi-soc-fixes-5.15' of https://github.com/AsahiLinux/linux into arm/fixes
Apple SoC fixes for 5.15; just two MAINTAINERS updates.
- MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
- MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
* tag 'asahi-soc-fixes-5.15' of https://github.com/AsahiLinux/linux:
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
Arnd Bergmann [Thu, 7 Oct 2021 19:14:03 +0000 (21:14 +0200)]
Merge tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
SCMI fixes for v5.15
A few fixes addressing:
- Kconfig dependency between VIRTIO and ARM_SCMI_PROTOCOL
- Link-time error with __exit annotation for virtio_scmi_exit
- Unnecessary nested irqsave/irqrestore spinlocks in virtio transport
- Missing SMP barriers to protect accesses to SCMI virtio device
* tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
firmware: arm_scmi: Remove __exit annotation
firmware: arm_scmi: Fix virtio transport Kconfig dependency
Arnd Bergmann [Thu, 7 Oct 2021 19:13:57 +0000 (21:13 +0200)]
Merge tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.15
Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:
- Fix compiler warning for sysc_init_soc() that got recently introduced
- Fix external abort for am335x pruss as otherwise some am335x will hang
- Use CLKDM_NOAUTO quirk also for dra7 dcan1
- Fix older NAND device node regression for omap3-sdp
* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
soc: ti: omap-prm: Fix external abort for am335x pruss
bus: ti-sysc: Add break in switch statement in sysc_init_soc()
Linus Torvalds [Thu, 7 Oct 2021 18:20:08 +0000 (11:20 -0700)]
Merge tag 'misc-fixes-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfslib, cachefiles and afs fixes from David Howells:
- Fix another couple of oopses in cachefiles tracing stemming from the
possibility of passing in a NULL object pointer
- Fix netfs_clear_unread() to set READ on the iov_iter so that source
it is passed to doesn't do the wrong thing (some drivers look at the
flag on iov_iter rather than other available information to determine
the direction)
- Fix afs_launder_page() to write back at the correct file position on
the server so as not to corrupt data
* tag 'misc-fixes-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix afs_launder_page() to set correct start file position
netfs: Fix READ/WRITE confusion when calling iov_iter_xarray()
cachefiles: Fix oops with cachefiles_cull() due to NULL object
Linus Torvalds [Thu, 7 Oct 2021 17:58:42 +0000 (10:58 -0700)]
Merge tag 'perf-tools-fixes-for-v5.15-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix plugin static linking with libopencsd on ARM and ARM64
- Add missing -lstdc++ when linking with libopencsd
- Add missing topdown metrics events to 'perf test attr'
- Plug leak sys_event_tables list after processing JSON vendor events
entries
- Sync sound/asound.h copy with the kernel sources
* tag 'perf-tools-fixes-for-v5.15-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tests attr: Add missing topdown metrics events
tools include UAPI: Sync sound/asound.h copy with the kernel sources
perf build: Fix plugin static linking with libopencsd on ARM and ARM64
perf build: Add missing -lstdc++ when linking with libopencsd
perf jevents: Free the sys_event_tables list after processing entries
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
Linus Torvalds [Thu, 7 Oct 2021 16:44:48 +0000 (09:44 -0700)]
Merge tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Replace uuid.h with types.h in a header (Andy Shevchenko)
- Avoid sleeping in atomic context in PCI driver (Long Li)
- Avoid sending IPI to self when it shouldn't (Vitaly Kuznetsov)
* tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Avoid erroneously sending IPI to 'self'
hyper-v: Replace uuid.h with types.h
PCI: hv: Fix sleep while in non-sleep context when removing child devices from the bus
PCI: ACPI: Check parent pointer in acpi_pci_find_companion()
If acpi_pci_find_companion() is called for a device whose parent
pointer is NULL, it will crash when attempting to get the ACPI
companion of the parent due to a NULL pointer dereference in
the ACPI_COMPANION() macro.
This was not a problem before commit 57920fc69c1f ("PCI: Setup ACPI
fwnode early and at the same time with OF") that made pci_setup_device()
call pci_set_acpi_fwnode() and so it allowed devices with NULL parent
pointers to be passed to acpi_pci_find_companion() which is the case
in pci_iov_add_virtfn(), for instance.
Fix this issue by making acpi_pci_find_companion() check the device's
parent pointer upfront and bail out if it is NULL.
While pci_iov_add_virtfn() can be changed to set the device's parent
pointer before calling pci_setup_device() for it, checking pointers
against NULL before dereferencing them is prudent anyway and looking
for ACPI companions of virtual functions isn't really useful.
Fixes: 57920fc69c1f ("PCI: Setup ACPI fwnode early and at the same time with OF") Link: https://lore.kernel.org/linux-acpi/8e4bbd5c59de31db71f718556654c0aa077df03d.camel@linux.ibm.com/ Reported-by: Niklas Schnelle <schnelle@linux.ibm.com> Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Add myself as a reviewer for Asahi Linux (Apple M1) patches.
I would like to be CC'ed on Asahi Linux patches for review and testing.
I am also collecting Asahi Linux patches downstream, rebasing on
linux-next periodically, and would like to be notified of what to
cherry-pick from lists.
Cc: Hector Martin <marcan@marcan.st> Cc: Sven Peter <sven@svenpeter.dev> Acked-by: Hector Martin <marcan@marcan.st> Acked-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Namjae Jeon [Sun, 3 Oct 2021 04:19:00 +0000 (13:19 +0900)]
ksmbd: fix oops from fuse driver
Marios reported kernel oops from fuse driver when ksmbd call
mark_inode_dirty(). This patch directly update ->i_ctime after removing
mark_inode_ditry() and notify_change will put inode to dirty list.
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Cc: Hyunchul Lee <hyc.lee@gmail.com> Reported-by: Marios Makassikis <mmakassikis@freebox.fr> Tested-by: Marios Makassikis <mmakassikis@freebox.fr> Acked-by: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Namjae Jeon [Fri, 1 Oct 2021 02:53:49 +0000 (11:53 +0900)]
ksmbd: fix version mismatch with out of tree
Fix version mismatch with out of tree, This updated version will be
matched with ksmbd-tools.
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Cc: Steve French <smfrench@gmail.com> Cc: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Namjae Jeon [Mon, 4 Oct 2021 11:44:52 +0000 (20:44 +0900)]
ksmbd: use buf_data_size instead of recalculation in smb3_decrypt_req()
Tom suggested to use buf_data_size that is already calculated, to verify
these offsets.
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Suggested-by: Tom Talpey <tom@talpey.com> Acked-by: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
ksmbd: remove the leftover of smb2.0 dialect support
Although ksmbd doesn't send SMB2.0 support in supported dialect list of smb
negotiate response, There is the leftover of smb2.0 dialect.
This patch remove it not to support SMB2.0 in ksmbd.
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Cc: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
ksmbd: check strictly data area in ksmbd_smb2_check_message()
When invalid data offset and data length in request,
ksmbd_smb2_check_message check strictly and doesn't allow to process such
requests.
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Acked-by: Hyunchul Lee <hyc.lee@gmail.com> Reviewed-by: Ralph Boehme <slow@samba.org> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Alex Elder <elder@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
firmware: include drivers/firmware/Kconfig unconditionally
Compile-testing drivers that require access to a firmware layer
fails when that firmware symbol is unavailable. This happened
twice this week:
- My proposed to change to rework the QCOM_SCM firmware symbol
broke on ppc64 and others.
- The cs_dsp firmware patch added device specific firmware loader
into drivers/firmware, which broke on the same set of
architectures.
We should probably do the same thing for other subsystems as well,
but fix this one first as this is a dependency for other patches
getting merged.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Mark Brown <broonie@kernel.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: Simon Trimmer <simont@opensource.cirrus.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Mark Brown <broonie@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mike Manning [Tue, 5 Oct 2021 13:03:42 +0000 (14:03 +0100)]
net: prefer socket bound to interface when not in VRF
The commit 9a8b1e4afec4 ("net: ensure unbound datagram socket to be
chosen when not in a VRF") modified compute_score() so that a device
match is always made, not just in the case of an l3mdev skb, then
increments the score also for unbound sockets. This ensures that
sockets bound to an l3mdev are never selected when not in a VRF.
But as unbound and bound sockets are now scored equally, this results
in the last opened socket being selected if there are matches in the
default VRF for an unbound socket and a socket bound to a dev that is
not an l3mdev. However, handling prior to this commit was to always
select the bound socket in this case. Reinstate this handling by
incrementing the score only for bound sockets. The required isolation
due to choosing between an unbound socket and a socket bound to an
l3mdev remains in place due to the device match always being made.
The same approach is taken for compute_score() for stream sockets.
Fixes: 9a8b1e4afec4 ("net: ensure unbound datagram socket to be chosen when not in a VRF") Fixes: 3af4247eb430 ("net: ensure unbound stream socket to be chosen when not in a VRF") Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/cf0a8523-b362-1edf-ee78-eef63cbbb428@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 7 Oct 2021 01:26:36 +0000 (18:26 -0700)]
Merge tag 'devicetree-fixes-for-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Add another allowed address for TI sn65dsi86
- Drop more redundant minItems/maxItems
- Fix more graph 'unevaluatedProperties' warnings in media bindings
* tag 'devicetree-fixes-for-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: drm/bridge: ti-sn65dsi86: Fix reg value
dt-bindings: Drop more redundant 'maxItems/minItems'
dt-bindings: media: Fix more graph 'unevaluatedProperties' related warnings
George Shen [Fri, 1 Oct 2021 14:36:09 +0000 (22:36 +0800)]
drm/amd/display: Skip override for preferred link settings during link training
[Why]
Overriding link setting inside override_training_settings
result in fallback link settings being ignored. This can
potentially cause link training to always fail and consequently
result in an infinite loop of link training to occur in
dp_verify_link_cap during detection.
[How]
Since preferred link settings are already considered inside
decide_link_settings, skip the check in override_training_settings
to avoid infinite link training loops.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If nfsd has existing listening sockets without any processes, then an error
returned from svc_create_xprt() for an additional transport will remove
those existing listeners. We're seeing this in practice when userspace
attempts to create rpcrdma transports without having the rpcrdma modules
present before creating nfsd kernel processes. Fix this by checking for
existing sockets before calling nfsd_destroy().
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stefan Assmann [Tue, 24 Aug 2021 10:06:39 +0000 (12:06 +0200)]
iavf: fix double unlock of crit_lock
The crit_lock mutex could be unlocked twice as reported here
https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20210823/025525.html
Remove the superfluous unlock. Technically the problem was already
present before 3e0a61a5b57d as that commit only replaced the locking
primitive, but no functional change.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 3e0a61a5b57d ("iavf: use mutexes for locking of critical sections") Fixes: 174bee62d924 ("iavf: Refactor the watchdog state machine") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e: Fix freeing of uninitialized misc IRQ vector
When VSI set up failed in i40e_probe() as part of PF switch set up
driver was trying to free misc IRQ vectors in
i40e_clear_interrupt_scheme and produced a kernel Oops:
The problem is that at that point misc IRQ vectors
were not allocated yet and we get a call trace
that driver is trying to free already free IRQ vectors.
Add a check in i40e_clear_interrupt_scheme for __I40E_MISC_IRQ_REQUESTED
PF state before calling i40e_free_misc_vector. This state is set only if
misc IRQ vectors were properly initialized.
Fixes: d1f935ddb561 ("i40e: use separate state bit for miscellaneous IRQ setup") Reported-by: PJ Waskiewicz <pwaskiewicz@jumptrading.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The loop in i40e_get_capabilities can never end. The problem is that
although i40e_aq_discover_capabilities returns with an error if there's
a firmware problem, the returned error is not checked. There is a check for
pf->hw.aq.asq_last_status but that value is set to I40E_AQ_RC_OK on most
firmware problems.
When i40e_aq_discover_capabilities encounters a firmware problem, it will
encounter the same problem on its next invocation. As the result, the loop
becomes endless. We hit this with I40E_ERR_ADMIN_QUEUE_TIMEOUT but looking
at the code, it can happen with a range of other firmware errors.
I don't know what the correct behavior should be: whether the firmware
should be retried a few times, or whether pf->hw.aq.asq_last_status should
be always set to the encountered firmware error (but then it would be
pointless and can be just replaced by the i40e_aq_discover_capabilities
return value). However, the current behavior with an endless loop under the
rtnl mutex(!) is unacceptable and Intel has not submitted a fix, although we
explained the bug to them 7 months ago.
This may not be the best possible fix but it's better than hanging the whole
system on a firmware bug.
Fixes: a948f4ab6b67 ("i40e: init code and hardware support") Tested-by: Stefan Assmann <sassmann@redhat.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
x86/hyperv: Avoid erroneously sending IPI to 'self'
__send_ipi_mask_ex() uses an optimization: when the target CPU mask is
equal to 'cpu_present_mask' it uses 'HV_GENERIC_SET_ALL' format to avoid
converting the specified cpumask to VP_SET. This case was overlooked when
'exclude_self' parameter was added. As the result, a spurious IPI to
'self' can be send.
Reported-by: Thomas Gleixner <tglx@linutronix.de> Fixes: 5994248446c1 ("x86/hyperv: remove on-stack cpumask from hv_send_ipi_mask_allbutself") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20211006125016.941616-1-vkuznets@redhat.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Arnd Bergmann [Wed, 6 Oct 2021 15:36:33 +0000 (17:36 +0200)]
Merge tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.15, round 2:
- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver
starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.
* tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
arm64: dts: imx8: change the spi-nor tx
ARM: dts: imx: change the spi-nor tx
Neil Armstrong [Tue, 28 Sep 2021 07:36:52 +0000 (09:36 +0200)]
mmc: meson-gx: do not use memcpy_to/fromio for dram-access-quirk
The memory at the end of the controller only accepts 32bit read/write
accesses, but the arm64 memcpy_to/fromio implementation only uses 64bit
(which will be split into two 32bit access) and 8bit leading to incomplete
copies to/from this memory when the buffer is not multiple of 8bytes.
Add a local copy using writel/readl accesses to make sure we use the right
memory access width.
The switch to memcpy_to/fromio was done because of 1da677916cf7
("arm64: Import latest memcpy()/memmove() implementation"), but using memcpy
worked before since it mainly used 32bit memory acceses.
Fixes: 679c02c6d867 ("mmc: meson-gx: use memcpy_to/fromio for dram-access-quirk") Reported-by: Christian Hewitt <christianshewitt@gmail.com> Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210928073652.434690-1-narmstrong@baylibre.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marcel Ziswiler [Wed, 6 Oct 2021 06:31:04 +0000 (08:31 +0200)]
dt-bindings: net: dsa: marvell: fix compatible in example
While the MV88E6390 switch chip exists, one is supposed to use a
compatible of "marvell,mv88e6190" for it. Fix this in the given example.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Fixes: 3a17ca7229f7 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Tue, 5 Oct 2021 23:11:05 +0000 (16:11 -0700)]
ionic: move filter sync_needed bit set
Move the setting of the filter-sync-needed bit to the error
case in the filter add routine to be sure we're checking the
live filter status rather than a copy of the pre-sync status.
Fixes: fd39dfc5c5a2 ("ionic: sync the filters in the work task") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 6 Oct 2021 01:01:38 +0000 (18:01 -0700)]
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
Each tx queue maintains a 64bit counter for bytes, there is
no reason to truncate this to 32bit (or this has not been
documented)
Fixes: 396efc7daa79 ("gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yangchun Fu <yangchun@google.com> Cc: Kuo Zhao <kuozhao@google.com> Cc: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 6 Oct 2021 00:30:30 +0000 (17:30 -0700)]
gve: fix gve_get_stats()
gve_get_stats() can report wrong numbers if/when u64_stats_fetch_retry()
returns true.
What is needed here is to sample values in temporary variables,
and only use them after each loop is ended.
Fixes: 17b7b5dff8f1 ("gve: Add transmit and receive support") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Catherine Sullivan <csully@google.com> Cc: Sagi Shahar <sagis@google.com> Cc: Jon Olson <jonolson@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Luigi Rizzo <lrizzo@google.com> Cc: Jeroen de Borst <jeroendb@google.com> Cc: Tao Liu <xliutaox@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: f3c866dc8f2d ("rtnetlink: add new RTM_GETSTATS message to dump link stats") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Roopa Prabhu <roopa@nvidia.com> Acked-by: Roopa Prabhu <roopa@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c783fba247857 ("gve: Add support for raw addressing to the rx path") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Liu [Wed, 6 Oct 2021 02:42:20 +0000 (19:42 -0700)]
gve: Avoid freeing NULL pointer
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: d9d932ac598ab ("gve: Add basic driver framework for Compute Engine Virtual NIC") Signed-off-by: Tao Liu <xliutaox@google.com> Signed-off-by: Catherine Sully <csully@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The qpl_map_size is rounded up to a multiple of sizeof(long), but the
number of qpls doesn't have to be.
Fixes: 17b7b5dff8f1f ("gve: Add transmit and receive support") Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: Jeroen de Borst <jeroendb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiang Wang [Mon, 4 Oct 2021 23:25:28 +0000 (23:25 +0000)]
unix: Fix an issue in unix_shutdown causing the other end read/write failures
Commit 8cee822891d7 ("af_unix: Add unix_stream_proto for sockmap") sets
unix domain socket peer state to TCP_CLOSE in unix_shutdown. This could
happen when the local end is shutdown but the other end is not. Then,
the other end will get read or write failures which is not expected.
Fix the issue by setting the local state to shutdown.
Fixes: 8cee822891d7 ("af_unix: Add unix_stream_proto for sockmap") Reported-by: Casey Schaufler <casey@schaufler-ca.com> Suggested-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Jiang Wang <jiang.wang@bytedance.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Casey Schaufler <casey@schaufler-ca.com> Reviewed-by: Casey Schaufler <casey@schaufler-ca.com> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20211004232530.2377085-1-jiang.wang@bytedance.com
Wong Vee Khee [Tue, 5 Oct 2021 11:51:00 +0000 (19:51 +0800)]
net: stmmac: trigger PCS EEE to turn off on link down
The current implementation enable PCS EEE feature in the event of link
up, but PCS EEE feature is not disabled on link down.
This patch makes sure PCE EEE feature is disabled on link down.
Fixes: ed829fbde9ba ("net: stmmac: fix EEE init issue when paired with EEE capable PHYs") Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wong Vee Khee [Tue, 5 Oct 2021 11:50:59 +0000 (19:50 +0800)]
net: pcs: xpcs: fix incorrect steps on disable EEE
When Energy-Efficient Ethernet(EEE) is disable from the MAC side,
we need to clear the DW_VR_MII_EEE_TRN_LPI bit of DW_VR_MII_EEE_MCTRL1
register.
Fixes: a8fbf22b480a ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet") Cc: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
firmware: arm_scmi: Add proper barriers to scmi virtio device
Only one single SCMI Virtio device is currently supported by this driver
and it is referenced using a static global variable which is initialized
once for all during probing and nullified at virtio device removal.
Add proper SMP barriers to protect accesses to such device reference to
ensure that the initialzation state of such device is correctly observed by
all PEs at any time.
Return -EBUSY, instead of -EINVAL, and a descriptive error message if more
than one SCMI Virtio device is ever found and probed.
Jeremy Cline [Thu, 3 Dec 2020 00:02:20 +0000 (19:02 -0500)]
drm/nouveau: avoid a use-after-free when BO init fails
nouveau_bo_init() is backed by ttm_bo_init() and ferries its return code
back to the caller. On failures, ttm_bo_init() invokes the provided
destructor which should de-initialize and free the memory.
Thus, when nouveau_bo_init() returns an error the gem object has already
been released and the memory freed by nouveau_bo_del_ttm().
Fixes: 26ea454bbfed ("drm/nouveau: Initialize GEM object before TTM object") Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Jeremy Cline <jcline@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201203000220.18238-1-jcline@redhat.com Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Mark Brown [Tue, 21 Sep 2021 21:21:02 +0000 (22:21 +0100)]
video: fbdev: gbefb: Only instantiate device when built for IP32
The gbefb driver not only registers a driver but also the device for that
driver. This is all well and good when run on the IP32 machines that are
supported by the driver but since the driver supports building with
COMPILE_TEST we might also be building on other platforms which do not have
this hardware and will crash instantiating the driver. Add an IS_ENABLED()
check so we compile out the device registration if we don't have the Kconfig
option for the machine enabled.
Fixes: afb7c1efb231f37486 ("video: fbdev: gbefb: add COMPILE_TEST support") Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20210921212102.30803-1-broonie@kernel.org Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Configurations with both CONFIG_FB_SIMPLE=y and CONFIG_DRM_SIMPLEDRM=m
are allowed by Kconfig because the 'depends on !DRM_SIMPLEDRM' dependency
does not disallow FB_SIMPLE as long as SIMPLEDRM is not built-in. This
can however result in a build failure when cfb_fillrect() etc are then
also in loadable modules:
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x1f8): undefined reference to `cfb_fillrect'
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x200): undefined reference to `cfb_copyarea'
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x208): undefined reference to `cfb_imageblit'
To work around this, change FB_SIMPLE to be a 'tristate' symbol,
which still allows both to be =m together, but not one of them to
be =y if the other one is =m. If a distro kernel picks this
configuration, it can be determined by local policy which of
the two modules gets loaded. The 'of_chosen' export is needed
as this is the first loadable module referencing it.
Alternatively, the Kconfig dependency could be changed to
'depends on DRM_SIMPLEDRM=n', which would forbid the configuration
with both drivers.
Fixes: b7390008b818 ("drm: Add simpledrm driver") Acked-by: Rob Herring <robh@kernel.org> # for drivers/of/ Link: https://lore.kernel.org/all/20210721151839.2484245-1-arnd@kernel.org/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> # fbdev support Cc: Maxime Ripard <maxime@cerno.tech> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Borislav Petkov <bp@suse.de> Cc: Javier Martinez Canillas <javierm@redhat.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Peter Collingbourne <pcc@google.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Cc: <stable@vger.kernel.org> # v5.14+ Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210928145243.1098064-1-arnd@kernel.org Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Morgan [Thu, 16 Sep 2021 20:29:07 +0000 (15:29 -0500)]
drm/rockchip: Update crtc fixup to account for fractional clk change
After commit 5a3fe49c2942 ("clk: fractional-divider: Hide
clk_fractional_divider_ops from wide audience") was merged it appears
that the DSI panel on my Odroid Go Advance stopped working. Upon closer
examination of the problem, it looks like it was the fixup in the
rockchip_drm_vop.c file was causing the issue. The changes made to the
clk driver appear to change some assumptions made in the fixup.
After debugging the working 5.14 kernel and the no-longer working
5.15 kernel, it looks like this was broken all along but still
worked, whereas after the fractional clock change it stopped
working despite the issue (it went from sort-of broken to very broken).
In the 5.14 kernel the dclk_vopb_frac was being requested to be set to 17000999 on my board. The clock driver was taking the value of the
parent clock and attempting to divide the requested value from it
(17000000/17000999 = 0), then subtracting 1 from it (making it -1),
and running it through fls_long to get 64. It would then subtract
the value of fd->mwidth from it to get 48, and then bit shift 17000999 to the left by 48, coming up with a very large number of 7649082492112076800. This resulted in a numerator of 65535 and a
denominator of 1 from the clk driver. The driver seemingly would
try again and get a correct 1:1 value later, and then move on.
Output from my 5.14 kernel (with some printfs for good measure):
[ 2.830066] rockchip-drm display-subsystem: bound ff460000.vop (ops vop_component_ops)
[ 2.839431] rockchip-drm display-subsystem: bound ff450000.dsi (ops dw_mipi_dsi_rockchip_ops)
[ 2.855980] Clock is dclk_vopb_frac
[ 2.856004] Scale 64, Rate 7649082492112076800, Oldrate 17000999, Parent Rate 17000000, Best Numerator 65535, Best Denominator 1, fd->mwidth 16
[ 2.903529] Clock is dclk_vopb_frac
[ 2.903556] Scale 0, Rate 17000000, Oldrate 17000000, Parent Rate 17000000, Best Numerator 1, Best Denominator 1, fd->mwidth 16
[ 2.903579] Clock is dclk_vopb_frac
[ 2.903583] Scale 0, Rate 17000000, Oldrate 17000000, Parent Rate 17000000, Best Numerator 1, Best Denominator 1, fd->mwidth 16
Contrast this with 5.15 after the clk change where the rate of 17000999
was getting passed and resulted in numerators/denomiators of 17001/
17000.
Output from my 5.15 kernel (with some printfs added for good measure):
[ 2.817571] rockchip-drm display-subsystem: bound ff460000.vop (ops vop_component_ops)
[ 2.826975] rockchip-drm display-subsystem: bound ff450000.dsi (ops dw_mipi_dsi_rockchip_ops)
[ 2.843430] Rate 17000999, Parent Rate 17000000, Best Numerator 17018, Best Denominator 17017
[ 2.891073] Rate 17001000, Parent Rate 17000000, Best Numerator 17001, Best Denominator 17000
[ 2.891269] Rate 17001000, Parent Rate 17000000, Best Numerator 17001, Best Denominator 17000
[ 2.891281] Rate 17001000, Parent Rate 17000000, Best Numerator 17001, Best Denominator 17000
I have tested the change extensively on my Odroid Go Advance (Rockchip
RK3326) and it appears to work well. However, this change will affect
all Rockchip SoCs that use this driver so I believe further testing
is warranted. Please note that without this change I can confirm
at least all PX30s with DSI panels will stop working with the 5.15
kernel.
Upon advice from Doug Anderson <dianders@chromium.org> it was decided
that we would first check if the clock rate can be set exactly as
requested, and only if it could not would we then add 999 to it and
attempt the process again. This way we can preserve the behavior for
clocks that still need it while resolving the specific issue for the
PX30 and DSI panels (since it is using a fractional clock).
Changes since v2:
- Moved fixes to correct location.
Changes since v1:
- Made the addition of 999 conditional based on whether the clock
subsystem can set the actual clock rate as requested.
- Updated the notes in the fixup routine to reflect this new behavior.
- Added reference to original commit, as this has technically been
broken since then however only now is it an issue due to the clock
changes.
Fixes: 6e76de6a2a97 ("clk: fractional-divider: Export approximation algorithm to the CCF users") Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210916202907.18394-1-macroalpha82@gmail.com Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ben Skeggs [Thu, 16 Sep 2021 22:04:06 +0000 (08:04 +1000)]
drm/nouveau/ga102-: support ttm buffer moves via copy engine
We don't currently have any kind of real acceleration on Ampere GPUs,
but the TTM memcpy() fallback paths aren't really designed to handle
copies between different devices, such as on Optimus systems, and
result in a kernel OOPS.
A few options were investigated to try and fix this, but didn't work
out, and likely would have resulted in a very unpleasant experience
for users anyway.
This commit adds just enough support for setting up a single channel
connected to a copy engine, which the kernel can use to accelerate
the buffer copies between devices. Userspace has no access to this
incomplete channel support, but it's suitable for TTM's needs.
A more complete implementation of host(fifo) for Ampere GPUs is in
the works, but the required changes are far too invasive that they
would be unsuitable to backport to fix this issue on current kernels.
v2: fix GPFIFO length in RAMFC (reported by Karol)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: Lyude Paul <lyude@redhat.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: <stable@vger.kernel.org> # v5.12+ Reviewed-by: Karol Herbst <kherbst@redhat.com> Tested-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210916220406.666454-1-skeggsb@gmail.com Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Recent rework, which made HDMI PHY driver a platform device, inadvertely
reversed clock setup order. HW is very touchy about it. Proper way is to
handle controllers resets and clocks first and HDMI PHYs second.
Currently, without this fix, first mode set completely fails (nothing on
HDMI monitor) on H3 era PHYs. On H6, it still somehow work.
Move HDMI PHY reset & clocks handling to sun8i_hdmi_phy_init() which
will assure that code is executed after controllers reset & clocks are
handled. Additionally, add sun8i_hdmi_phy_deinit() which will deinit
them at controllers driver unload.
Maxime Ripard [Thu, 19 Aug 2021 14:07:53 +0000 (16:07 +0200)]
drm/vc4: hdmi: Remove unused struct
Commitc7d30623540b ("drm/vc4: hdmi: Remove unused struct") removed the
references to the vc4_hdmi_audio_widgets and vc4_hdmi_audio_routes
structures, but not the structures themselves resulting in two warnings.
Remove it.
Fixes: 3aa48ca7177b ("drm/vc4: hdmi: Remove unused struct") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210819140753.930751-1-maxime@cerno.tech Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
ksmbd: add the check to vaildate if stream protocol length exceeds maximum value
This patch add MAX_STREAM_PROT_LEN macro and check if stream protocol
length exceeds maximum value. opencode pdu size check in
ksmbd_pdu_size_has_room().
Cc: Tom Talpey <tom@talpey.com> Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com> Cc: Ralph Böhme <slow@samba.org> Acked-by: Hyunchul Lee <hyc.lee@gmail.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com>
Tony Lindgren [Wed, 8 Sep 2021 05:49:36 +0000 (08:49 +0300)]
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
Commit 4f6a2c0895a7 ("bus: ti-sysc: Implement quirk handling for
CLKDM_NOAUTO") should have also added the quirk for dra7 dcan1 in
addition to dcan2 for errata i893 handling.
Let's also pass the quirk flag for legacy mode booting for if "ti,hwmods"
dts property is used with related dcan hwmod data. This should be only
needed if anybody needs to git bisect earlier stable trees though.
Fixes: 4f6a2c0895a7 ("bus: ti-sysc: Implement quirk handling for CLKDM_NOAUTO") Signed-off-by: Tony Lindgren <tony@atomide.com>
Guenter Roeck [Sun, 1 Aug 2021 17:36:59 +0000 (10:36 -0700)]
xtensa: xtfpga: Try software restart before simulating CPU reset
Rebooting xtensa images loaded with the '-kernel' option in qemu does
not work. When executing a reboot command, the qemu session either hangs
or experiences an endless sequence of error messages.
Kernel panic - not syncing: Unrecoverable error in exception handler
Reset code jumps to the CPU restart address, but Linux can not recover
from there because code and data in the kernel init sections have been
discarded and overwritten at this point.
XTFPGA platforms have a means to reset the CPU by writing 0xdead into a
specific FPGA IO address. When used in QEMU the kernel image loaded with
the '-kernel' option gets restored to its original state allowing the
machine to boot successfully.
Use that mechanism to attempt a platform reset. If it does not work,
fall back to the existing mechanism.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Max Filippov [Tue, 5 Oct 2021 18:36:01 +0000 (11:36 -0700)]
xtensa: xtfpga: use CONFIG_USE_OF instead of CONFIG_OF
Use platform data to initialize xtfpga device drivers when CONFIG_USE_OF
is not selected. This fixes xtfpga networking when CONFIG_USE_OF is not
selected but CONFIG_OF is.
The Topdown metrics events were added as 'perf stat' default events
since commit 1eda7931365c2737 ("perf stat: Add Topdown metrics events as
default events").
However, the perf attr tests were not updated
accordingly.
The perf attr test fails on the platform which supports Topdown metrics.
# perf test 17
17: Setup struct perf_event_attr :FAILED!
Add Topdown metrics events into perf attr test cases. Make them optional
since they are only available on newer platforms.
Fixes: 1eda7931365c2737 ("perf stat: Add Topdown metrics events as default events") Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lore.kernel.org/lkml/1633031566-176517-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Tue, 5 Oct 2021 17:52:53 +0000 (10:52 -0700)]
Merge tag 'warning-fixes-20211005' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull misc fs warning fixes from David Howells:
"The first four patches fix kerneldoc warnings in fscache, afs, 9p and
nfs - they're mostly just comment changes, though there's one place in
9p where a comment got detached from the function it was attached to
(v9fs_fid_add) and has to switch places with a function that got
inserted between (__add_fid).
The patch on the end removes an unused symbol in fscache"
* tag 'warning-fixes-20211005' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
fscache: Remove an unused static variable
fscache: Fix some kerneldoc warnings shown up by W=1
9p: Fix a bunch of kerneldoc warnings shown up by W=1
afs: Fix kerneldoc warning shown up by W=1
nfs: Fix kerneldoc warning shown up by W=1
Which entails no changes in the tooling side as it doesn't introduce new
SNDRV_PCM_IOCTL_ ioctls.
To silence this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
diff -u tools/include/uapi/sound/asound.h include/uapi/sound/asound.h
Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf build: Fix plugin static linking with libopencsd on ARM and ARM64
Filter out -static flag when building plugins as they are always built
as dynamic libraries and -static and -dynamic don't work well together
on arm and arm64.
Signed-off-by: Branislav Rankov <branislav.rankov@arm.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mark Brown <Mark.Brown@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: coresight@lists.linaro.org Cc: nd@arm.com Link: https://lore.kernel.org/r/e88952b3-2470-da96-dee9-e247a1759cd0@arm.com Signed-off-by: Tamas Zsoldos <tamas.zsoldos@arm.com>
[ Split from a larger patch ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Like Xu [Tue, 28 Sep 2021 10:29:38 +0000 (18:29 +0800)]
perf jevents: Free the sys_event_tables list after processing entries
The compiler reports that free_sys_event_tables() is dead code.
But according to the semantics, the "LIST_HEAD(sys_event_tables)" should
also be released, just like we do with 'arch_std_events' in main().
Fixes: 32ccb717bdc87c0d ("perf vendor events: Add support for arch standard events") Signed-off-by: Like Xu <likexu@tencent.com> Reviewed-by: John Garry <john.garry@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210928102938.69681-1-likexu@tencent.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Guchun Chen [Fri, 1 Oct 2021 01:48:50 +0000 (09:48 +0800)]
drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume
In current code, when a PCI error state pci_channel_io_normal is detectd,
it will report PCI_ERS_RESULT_CAN_RECOVER status to PCI driver, and PCI
driver will continue the execution of PCI resume callback report_resume by
pci_walk_bridge, and the callback will go into amdgpu_pci_resume
finally, where write lock is releasd unconditionally without acquiring
such lock first. In this case, a deadlock will happen when other threads
start to acquire the read lock.
To fix this, add a member in amdgpu_device strucutre to cache
pci_channel_state, and only continue the execution in amdgpu_pci_resume
when it's pci_channel_io_frozen.
This patch is to fix clinfo failure in Raven/Picasso:
Number of platforms: 1
Platform Profile: FULL_PROFILE
Platform Version: OpenCL 2.2 AMD-APP (3364.0)
Platform Name: AMD Accelerated Parallel Processing
Platform Vendor: Advanced Micro Devices, Inc.
Platform Extensions: cl_khr_icd cl_amd_event_callback
Platform Name: AMD Accelerated Parallel Processing Number of devices: 0
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: James Zhu <James.Zhu@amd.com> Tested-by: James Zhu <James.Zhu@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: James Zhu <James.Zhu@amd.com> Tested-by: James Zhu <James.Zhu@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lijo Lazar [Fri, 1 Oct 2021 08:49:07 +0000 (16:49 +0800)]
drm/amdgpu: During s0ix don't wait to signal GFXOFF
In the rare event when GFX IP suspend coincides with a s0ix entry, don't
schedule a delayed work, instead signal PMFW immediately to allow GFXOFF
entry. GFXOFF is a prerequisite for s0ix entry. PMFW needs to be
signaled about GFXOFF status before amd-pmc module passes OS HINT
to PMFW telling that everything is ready for a safe s0ix entry.
projects / kernel.git / log