In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
The commit e40f514a7a37 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 16eab3aa731c ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 2ba575a761cd ("power: bq27xxx_battery: Add interrupt handling support") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: dd2dd2078771 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: a1c7f7f219bf ("power_supply: Add new LED trigger charging-blink-solid-full") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: f57843b84709 ("[IPV6]: Find option offset by type.") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A narrow load from a 64-bit context field results in a 64-bit load
followed potentially by a 64-bit right-shift and then a bitwise AND
operation to extract the relevant data.
In the case of a 32-bit access, an immediate mask of 0xffffffff is used
to construct a 64-bit BPP_AND operation which then sign-extends the mask
value and effectively acts as a glorified no-op. For example:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
results in the following code generation for a 64-bit field:
In the end of the test, there will be an error message induced by the
`ip netns del ns1` command in cleanup()
Tests passed: 201
Tests failed: 0
Cannot remove namespace file "/run/netns/ns1": No such file or directory
This can even be reproduced with just `./fib_tests.sh -h` as we're
calling cleanup() on exit.
Redirect the error message to /dev/null to mute it.
V2: Update commit message and fixes tag.
V3: resubmit due to missing netdev ML in V2
Fixes: b60417a9f2b8 ("selftest: fib_tests: Always cleanup before exit") Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
these endpoints (and similarly for the radio-shark driver).
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
the endpoints.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
syzbot reported [0] a null-ptr-deref in sk_get_rmem0() while using
IPPROTO_UDPLITE (0x88):
14:25:52 executing program 1:
r0 = socket$inet6(0xa, 0x80002, 0x88)
We had a similar report [1] for probably sk_memory_allocated_add()
in __sk_mem_raise_allocated(), and commit 095fa7ce76f9 ("udplite: fix
NULL pointer dereference") fixed it by setting .memory_allocated for
udplite_prot and udplitev6_prot.
To fix the variant, we need to set either .sysctl_wmem_offset or
.sysctl_rmem.
Now UDP and UDPLITE share the same value for .memory_allocated, so we
use the same .sysctl_wmem_offset for UDP and UDPLITE.
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com Fixes: 8e74e15a285b ("net/core: generic support for disabling netdev features down stack") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer detected a problem in the udlfb driver, caused by an
endpoint not having the expected type:
usb 1-1: Read EDID byte 0 failed: -71
usb 1-1: Unable to get valid EDID from device/display
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 9 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880
drivers/usb/core/urb.c:504
Modules linked in:
CPU: 0 PID: 9 Comm: kworker/0:1 Not tainted 6.4.0-rc1-syzkaller-00016-ga4422ff22142 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
04/28/2023
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
dlfb_submit_urb+0x92/0x180 drivers/video/fbdev/udlfb.c:1980
dlfb_set_video_mode+0x21f0/0x2950 drivers/video/fbdev/udlfb.c:315
dlfb_ops_set_par+0x2a7/0x8d0 drivers/video/fbdev/udlfb.c:1111
dlfb_usb_probe+0x149a/0x2710 drivers/video/fbdev/udlfb.c:1743
The current approach for this issue failed to catch the problem
because it only checks for the existence of a bulk-OUT endpoint; it
doesn't check whether this endpoint is the one that the driver will
actually use.
We can fix the problem by instead checking that the endpoint used by
the driver does exist and is bulk-OUT.
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation.
Traditionally, all CPUs in a system have identical numbers of SMT
siblings. That changes with hybrid processors where some logical CPUs
have a sibling and others have none.
Today, the CPU boot code sets the global variable smp_num_siblings when
every CPU thread is brought up. The last thread to boot will overwrite
it with the number of siblings of *that* thread. That last thread to
boot will "win". If the thread is a Pcore, smp_num_siblings == 2. If it
is an Ecore, smp_num_siblings == 1.
smp_num_siblings describes if the *system* supports SMT. It should
specify the maximum number of SMT threads among all cores.
Ensure that smp_num_siblings represents the system-wide maximum number
of siblings by always increasing its value. Never allow it to decrease.
On MeteorLake-P platform, this fixes a problem that the Ecore CPUs are
not updated in any cpu sibling map because the system is treated as an
UP system when probing Ecore CPUs.
Below shows part of the CPU topology information before and after the
fix, for both Pcore and Ecore CPU (cpu0 is Pcore, cpu 12 is Ecore).
...
-/sys/devices/system/cpu/cpu0/topology/package_cpus:000fff
-/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-11
+/sys/devices/system/cpu/cpu0/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu0/topology/package_cpus_list:0-21
...
-/sys/devices/system/cpu/cpu12/topology/package_cpus:001000
-/sys/devices/system/cpu/cpu12/topology/package_cpus_list:12
+/sys/devices/system/cpu/cpu12/topology/package_cpus:3fffff
+/sys/devices/system/cpu/cpu12/topology/package_cpus_list:0-21
Notice that the "before" 'package_cpus_list' has only one CPU. This
means that userspace tools like lscpu will see a little laptop like
an 11-socket system:
-Core(s) per socket: 1
-Socket(s): 11
+Core(s) per socket: 16
+Socket(s): 1
This is also expected to make the scheduler do rather wonky things
too.
[ dhansen: remove CPUID detail from changelog, add end user effects ]
CC: stable@kernel.org Fixes: 197c15c68a0c ("x86: use cpuid vector 0xb when available for detecting cpu topology") Fixes: 1eabe5c2323d ("x86/cpu/topology: Provide detect_extended_topology_early()") Suggested-by: Len Brown <len.brown@intel.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/all/20230323015640.27906-1-rui.zhang%40intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardik Garg [Fri, 26 May 2023 23:21:36 +0000 (16:21 -0700)]
selftests/memfd: Fix unknown type name build failure
Partially backport v6.3 commit 11f75a01448f ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:
fuse_test.c:64:8: error: unknown type name '__u64'
64 | static __u64 mfd_assert_get_seals(int fd)
This header includes the __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.
The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)
Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.
As a workaround, never enable PCIDs on affected processors.
I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.
Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because when we abort the transaction in the transaction
commit path we call invalidate_inode_pages2_range on our block group
cache inodes (if we have space cache v1) and any delalloc inodes we may
have. The plain invalidate_inode_pages2_range() call passes through
GFP_KERNEL, which makes sense in most cases, but not here. Wrap these
two invalidate callees with memalloc_nofs_save/memalloc_nofs_restore to
make sure we don't end up with the fs reclaim dependency under the
transaction dependency.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's debugfs files have had a read operation since commit 4ed6199559fe ("gpio: mockup: rework debugfs interface"), but were
still being created with write-only mode bits. Update them to
indicate that the files can also be read.
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
Some compilers (tested with 4.8.5 from CentOS 7) fail properly process
FIELD_GET inside an inline function, which ends up in a BUILD_BUG_ON.
Convert inline function to a macro.
Fixes commit c45085ce7cf8 ("mt76: mt7615: add support for per-chain
signal strength reporting")
Reported in https://lkml.org/lkml/2019/9/21/146
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Pablo Greco <pgreco@centosproject.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Cc: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
The watchdog countdown is supposed to begin when the device file is
opened. Instead, it would begin countdown upon the first write to or
close of the device file. Now, the ping operation is called within the
start operation which ensures the countdown begins. From experimenation,
it does not appear possible to do this with a single write including
both the start bit and the trigger bit. So, it is done as two distinct
writes.
Use "a" constraint instead of "d" constraint to pass the state parameter to
the do_sqbs() inline assembly. This prevents that general purpose register
zero is used for the state parameter.
If the compiler would select general purpose register zero this would be
problematic for the used instruction in rsy format: the register used for
the state parameter is a base register. If the base register is general
purpose register zero the contents of the register are unexpectedly ignored
when the instruction is executed.
This only applies to z/VM guests using QIOASSIST with dedicated (pass through)
QDIO-based devices such as FCP [zfcp driver] as well as real OSA or
HiperSockets [qeth driver].
A possible symptom for this case using zfcp is the following repeating kernel
message pattern:
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: qdio: ZFCP on SC <sc> using AI:1 QEBSM:1 PRI:1 TDD:1 SIGA: W
zfcp <devbusid>: A QDIO problem occurred
zfcp <devbusid>: A QDIO problem occurred
Each of the qdio problem message can be accompanied by the following entries
for the affected subchannel <sc> in
/sys/kernel/debug/s390dbf/qdio_error/hex_ascii for zfcp or qeth:
After a call to console_unlock() in vcs_write() the vc_data struct can be
freed by vc_port_destruct(). Because of that, the struct vc_data pointer
must be reloaded in the while loop in vcs_write() after console_lock() to
avoid a UAF when vcs_size() is called.
Syzkaller reported a UAF in vcs_size().
BUG: KASAN: slab-use-after-free in vcs_size (drivers/tty/vt/vc_screen.c:215)
Read of size 4 at addr ffff8880beab89a8 by task repro_vcs_size/4119
The buggy address belongs to the object at ffff8880beab8800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 424 bytes inside of
freed 1024-byte region [ffff8880beab8800, ffff8880beab8c00)
It is weird to fetch the information from the inode over and over. Read
and write already have the needed information, so rewrite vcs_size to
accept a vc, attr and unicode and adapt vcs_lseek to that.
Also make sure all sites check the return value of vcs_size for errors.
And document it using kernel-doc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20200818085706.12163-5-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 8fb9ea65c9d1 ("vc_screen: reload load of struct vc_data pointer in vcs_write() to avoid UAF") Signed-off-by: Sasha Levin <sashal@kernel.org>
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
The USB ethernet gadget driver implements its own print macros which
call printk. Device drivers should use the device prints that print the
device name. Fortunately, the same macro names are defined in the header
file 'linux/usb/composite.h' and these use the device prints. Therefore,
remove the local definitions in the USB ethernet gadget driver and use
those in 'linux/usb/composite.h'. The only difference is that now the
device name is printed instead of the ethernet interface name.
Tested using ethernet gadget on Jetson AGX Orin.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20230209125319.18589-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3c0f4f09c063 ("usb: gadget: u_ether: Fix host MAC address case") Signed-off-by: Sasha Levin <sashal@kernel.org>
Prox-out events may not be reliably sent by some AES firmware. This can
cause problems for users, particularly due to arbitration logic disabling
touch input while the pen is in prox.
This commit adds a timer which is reset every time a new prox event is
received. When the timer expires we check to see if the pen is still in
prox and force it out if necessary. This is patterend off of the same
solution used by 'hid-letsketch' driver which has a similar problem.
clean_net() runs in workqueue while walking over the lists, grab mutex.
Fixes: 815fac68e781 ("netfilter: nftables: fix possible UAF over chains from packet path in netns") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add helper function to parse the set element key netlink attribute.
v4: No changes
v3: New patch
[sbrivio: refactor error paths and labels; use NFT_DATA_VALUE_MAXLEN
instead of sizeof(*key) in helper, value can be longer than that;
rebase] Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached.
It was reported that soft dirty tracking doesn't work when using the
Radix MMU.
The tracking is supposed to work by clearing the soft dirty bit for a
mapping and then write protecting the PTE. If/when the page is written
to, a page fault occurs and the soft dirty bit is added back via
pte_mkdirty(). For example in wp_page_reuse():
Unfortunately on radix _PAGE_SOFTDIRTY is being dropped by
radix__ptep_set_access_flags(), called from ptep_set_access_flags(),
meaning the soft dirty bit is not set even though the page has been
written to.
Fix it by adding _PAGE_SOFTDIRTY to the set of bits that are able to be
changed in radix__ptep_set_access_flags().
The P360 Tiny suffers from an irq storm issue like the T490s, so add
an entry for it to tpm_tis_dmi_table, and force polling. There also
previously was a report from the previous attempt to enable interrupts
that involved a ThinkPad L490. So an entry is added for it as well.
Cc: stable@vger.kernel.org Reported-by: Peter Zijlstra <peterz@infradead.org> # P360 Tiny Closes: https://lore.kernel.org/linux-integrity/20230505130731.GO83892@hirez.programming.kicks-ass.net/ Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the MClientSnap reqeust's op is not CEPH_SNAP_OP_SPLIT the
request may still contain a list of 'split_realms', and we need
to skip it anyway. Or it will be parsed as a corrupt snaptrace.
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
If a vCPU is outside guest mode and is scheduled out, it might be in the
process of making a memory access. A problem occurs if another vCPU uses
the PV TLB flush feature during the period when the vCPU is scheduled
out, and a virtual address has already been translated but has not yet
been accessed, because this is equivalent to using a stale TLB entry.
To avoid this, only report a vCPU as preempted if sure that the guest
is at an instruction boundary. A rescheduling request will be delivered
to the host physical CPU as an external interrupt, so for simplicity
consider any vmexit *not* instruction boundary except for external
interrupts.
It would in principle be okay to report the vCPU as preempted also
if it is sleeping in kvm_vcpu_block(): a TLB flush IPI will incur the
vmentry/vmexit overhead unnecessarily, and optimistic spinning is
also unlikely to succeed. However, leave it for later because right
now kvm_vcpu_check_block() is doing memory accesses. Even
though the TLB flush issue only applies to virtual memory address,
it's very much preferrable to be conservative.
Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[OP: use VCPU_STAT() for debugfs entries] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: ea3f54dd9351 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices") Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control message provided by J1939 support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.
Link: https://github.com/hartkopp/can-isotp/issues/59 Cc: Oleksij Rempel <o.rempel@pengutronix.de> Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Fixes: 877b9bba3266 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/20230505110308.81087-3-mkl@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_line_out_pfx() may trigger an Oops by overflowing the static array
with more than 8 channels. This was reported for MacBookPro 12,1 with
Cirrus codec.
As a workaround, extend for the 9.1 channels and also fix the
potential Oops by unifying the code paths accessing the same array
with the proper size check.
This patch fixes negative indexing of buf array in pin_assignment_show
when get_current_pin_assignments returns 0 i.e. no compatible pin
assignments are found.
When the dwc3 device is runtime suspended, various required clocks are in
disabled state and it is not guaranteed that access to any registers would
work. Depending on the SoC glue, a register read could be as benign as
returning 0 or be fatal enough to hang the system.
In order to prevent such scenarios of fatal errors, make sure to resume
dwc3 then allow the function to proceed.
OverCurrent condition is not standardized in the UHCI spec.
Zhaoxin UHCI controllers report OverCurrent bit active off.
In order to handle OverCurrent condition correctly, the uhci-hcd
driver needs to be told to expect the active-off behavior.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20230423105952.4526-1-WeitaoWang-oc@zhaoxin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
The syzbot fuzzer found a problem in the usbtmc driver: When a user
submits an ioctl for a 0-length control transfer, the driver does not
check that the direction is set to OUT:
CPU: 0 PID: 29770 Comm: syz-executor.0 Not tainted 6.3.0-rc6-syzkaller-gc478e5b17829 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: d49a2a41710f ("igb: PCI-Express 82575 Gigabit Ethernet driver") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: c4897a27ebe9 ("cassini: use request_firmware") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: 6601d5a7c259 ("net: bcmgenet: connect and disconnect from the PHY state machine") Fixes: 93e0401e0fc0 ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: 6601d5a7c259 ("net: bcmgenet: connect and disconnect from the PHY state machine") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
The empty stub functions are defined as global functions, which
causes a warning because of missing prototypes:
drivers/gpu/drm/exynos/exynos_drm_g2d.h:37:5: error: no previous prototype for 'g2d_open'
drivers/gpu/drm/exynos/exynos_drm_g2d.h:42:5: error: no previous prototype for 'g2d_close'
Mark them as 'static inline' to avoid the warning and to make
them behave as intended.
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 396acb0485ed ("net: hns3: Add support to reset the enet/ring mgmt layer") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 211c0939a183 ("net: hns3: adjust the process of PF reset") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit f6ed7126ce09 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: f6ed7126ce09 ("erspan: build the header with the right proto according to erspan_ver") Fixes: f2bf205dab51 ("ip6_gre: add erspan v2 support") Reported-by: Kevin Traynor <ktraynor@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the
following sequence of events:
1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
add ... external". "ip" ignores "[o]seq" if "external" is specified,
so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:
Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by
making o_seqno atomic_t.
As mentioned by Eric Dumazet in commit 6f5ce4d7ff17 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.
Maybe a better fix would be:
1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if
they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
with "oseq".
Unfortunately, that would break userspace.
We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 359dae890f7b ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode. According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.
Fixes: 3d8fd70921d8 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
1. During ip6gretap device initialization, tunnel->tun_hlen (e.g. 4) is
calculated based on old flags (see ip6gre_calc_hlen());
2. packet_snd() reserves header room for skb A, assuming
tunnel->tun_hlen is 4;
3. Later (in clsact Qdisc), the eBPF program sets a new tunnel key for
skb A using bpf_skb_set_tunnel_key() (see _ip6gretap_set_tunnel());
4. __gre6_xmit() detects the new tunnel key, and recalculates
"tun_hlen" (e.g. 12) based on new flags (e.g. TUNNEL_KEY and
TUNNEL_SEQ);
5. gre_build_header() calls skb_push() with insufficient reserved header
room, triggering the BUG.
As sugguested by Cong, fix it by moving the call to skb_cow_head() after
the recalculation of tun_hlen.
ip netns add at_ns0
ip link add veth0 type veth peer name veth1
ip link set veth0 netns at_ns0
ip netns exec at_ns0 ip addr add 172.16.1.100/24 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip link set dev veth1 up mtu 1500
ip addr add dev veth1 172.16.1.200/24
ip netns exec at_ns0 ip addr add ::11/96 dev veth0
ip netns exec at_ns0 ip link set dev veth0 up
ip addr add dev veth1 ::22/96
ip link set dev veth1 up
ip netns exec at_ns0 \
ip link add dev ip6gretap00 type ip6gretap seq flowlabel 0xbcdef key 2 \
local ::11 remote ::22
ip netns exec at_ns0 ip addr add dev ip6gretap00 10.1.1.100/24
ip netns exec at_ns0 ip addr add dev ip6gretap00 fc80::100/96
ip netns exec at_ns0 ip link set dev ip6gretap00 up
ip link add dev ip6gretap11 type ip6gretap external
ip addr add dev ip6gretap11 10.1.1.200/24
ip addr add dev ip6gretap11 fc80::200/24
ip link set dev ip6gretap11 up
tc qdisc add dev ip6gretap11 clsact
tc filter add dev ip6gretap11 egress bpf da obj $OBJ sec ip6gretap_set_tunnel
tc filter add dev ip6gretap11 ingress bpf da obj $OBJ sec ip6gretap_get_tunnel
ping6 -c 3 -w 10 -q ::11
Fixes: 4469230eef55 ("ip6_gre: add ip6 gre and gretap collect_md mode") Reported-by: Feng Zhou <zhoufeng.zf@bytedance.com> Co-developed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d80fc101d2eb ("erspan: get the proto with the md version for collect_md") Signed-off-by: Sasha Levin <sashal@kernel.org>
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: e9d736dd26b5 ("VSOCK: Introduce VM Sockets") Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This code was supposed to return an error code if init_stream()
failed, but it instead freed dg00x->rx_stream and returned success.
This potentially leads to a use after free.
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
projects / kernel.git / log